Search Documents

For some time fine coal (-0.5 mm) flot ation has been considered as a bulk flotation problem. Combinations of hydrocarbon oils and frothers have been used as surface active agents in coal flotation. The selectivity of the flotation process has always been poor in such cases. With the increase in fine coal production due to mining methods and coal handling systems, optimisation of fine coal treatment.has become important. Petrographic and mineralogical composit- ions of coal particles have been reported to influence their flotability. The problem becomes more complex due to surface oxidation of coal and the presence of slime forming clay minerals in the run of mine coal. In this paper, the flotation problem is examined on the basis of various constituents of coal and their associated gangue minerals. The selection of reagents has been suggested on the basis of their surface chemical properties. Factors such as surface modific- ation of coal and gangue materials, flotation kinetics and hydrocarbon oil - coal inter- action have been critically evaluated to improve fine coal flotation recovery.

Jan 1, 1978

By T Baumgartl, R Akesseh, M Edraki, B Usher, M Shaygan

With the continuing demand for industrialisation and urbanisation, the rate of mining and processing lower grade ores will also increase, producing large quantities of waste. As extreme weather events associated with global climatic changes are to be expected, the risk from mine tailings management will also increase (Edraki et al., 2014). In sulfide rich tailings, weathering within the critical zone controls the fate and distribution of the contaminants such as copper, zinc, and lead in the environment (Hayes et al., 2014). Tailings evolve geochemically and physically with time as they age under the influence of complex interacting factors. Understanding of the complex interactions between these controlling factors is important for predicting and mitigating the potential risks associated with sulfide tailings such as generation of acid mine drainage (Lindsay et al., 2015). Wetting and drying initiates weathering processes, influencing the hydrological, geochemical and geomechanical properties of the tailings. In semi-arid climates where evaporation exceeds precipitation, salts may precipitate within the pore system as well as on the tailings surface. These salts become the temporal sink of heavy metals until the next episodic rainfall (Nordstrom, 2011, Grover et al., 2016). Therefore, using kinetic and static test to describe the trajectory of these material evolutions without considering the complex interactions could potentially lead to erroneous prediction. In order to understand these relations, the effect of drying and wetting cycles on the hydrological, geochemical and geomechanical properties of ageing tailings was studied to draw conclusions for advanced tailings site rehabilitation and mine closureCITATION:Akesseh, R, Shaygan, M, Usher, B, Edraki, M and Baumgartl, T, 2018. Wetting and drying cycles as a means to determine the effect and consequences of tailings ageing, in Proceedings Life-of-Mine 2018, pp 24–27 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

NEARLY all problems in mining engineering involve the transport and distribution of materials from place to place, and in general the most economically managed mines and plants are those in which the transport of materials has been carried out most efficiently. Of all these transport problems, the hoisting of ore out of the mine and the distribution of same to the various treatment works is perhaps one of the most important. It is proposed in the present paper to traverse the conditions,affecting the location, scale of operations, and design of the main shaft and head gear at the Mount Morgan mine; afterwards describing the designs and workings of the shaft house, winding engine, and transport from the shaft house to the treatment works.LOCATIONWhen the copper-gold ore was developed sufficiently to determine approximately the boundaries of the ore-body, it was found that the existing vertical shafts would be wholly inadequate to deal with the increased quantity of ore required to be handled. It was proposed, therefore, to construct a new shaft, and to handle in this...

Jan 1, 1911

Process variables in flotation circuits are outlined with a view to producing mathematical models of circuits. The nature of the kinetics of flotation are discussed and the effect of process variables on the kinetics considered. An approach for a possible model is briefly outlined.

Jan 1, 1971

The region we call the West Coast is acknowledged as one of the richest and most diverse mineral provinces in the world. It's the most rugged part of Tasmania and our island is one of the most rugged parts of Australia, so that speaks for itself. A hostile land of razorback mountains, deep ravines, dangerous rivers, almost impenetrable rainforests and a climate that can change from mild to freezing in a matter of hours.

Jan 1, 1993

By L H. G McClean

Diversity, equity and inclusion are often cited as ‘important priorities’ by mining companies and industry organisations in their public presentations and reports, but is the minerals industry really making strides forward? The mining industry is the least gender diverse industry in Australia (WEGA, 2023). Women make up just 22 per cent of the mining workforce and mining has a gender pay gap of 15.1 per cent (WEGA, 2024a). Only 8 per cent of the CEO roles are female and 20 per cent of boards have no female members (WEGA, 2023, 2024a). Gender diversity, equity and inclusion is a highly topical issue with the recent release of the Respect@Work report, Western Australia Parliamentary Inquiry as well as the publication of company specific workplace culture reports and the national legislative changes to implement a positive duty for organisations to prevent sexual harassment in the workplace. This comes at a time of a skills and labour shortage in the minerals industry as well as declining geoscience study and participation. This is a perfect storm for our future workforce. Governments, industry associations, networks and companies are developing and supporting initiatives to make strides towards equity and inclusion, with some shining examples on both an industry and company level, but the dial is only moving slowly and, in some ways, going backwards. Every company is unique, but every company can review and support gender diversity, equity and inclusion. Actions to progress gender parity could include establishing a clear company position; ensuring that this position is cascaded throughout the company with appropriate training; reporting and reviewing gender participation as well as supporting positive workforce initiatives and a positive culture with a people-centric issues reporting process. At the industry level, there are clear gaps in the support for gender diversity and inclusion including a national voice and ‘one-stop-shop’ to support women in the industry and provide resources. Recommendations include improved co-ordination and collaboration of support for women as well as improved promotion of the suitability (and safety) of the industry for women. The new independent organisation, Women in Mining and Resources Australia (WIMARA) has the objective to address the challenges of gender diversity and inclusion as well as foster co-ordination, co-operation and collaboration between the different stakeholders and state or territory groups and amplify reach. To deliver the future workforce that the minerals industry needs, the time is now for the industry to make some giant leaps for womankind.

Sep 1, 2024

This paper outlines the advances made in vacuum filtration as developed by Outomec Process Filters and details the results obtained at a number of Australian installations. The first section of the paper details the technical advances made by the use of ceramic media in vacuum filtration and explains the reasons for the use of the technology. The second part of the paper discusses a number of Australian installations of the ceramic vacuum filter and where possible compares the actual experiences with those predicted from the test work which preceded the installations. The Ceramec Capillary Vacuum Filter is a vacuum disc filter which combines the proven mechanical attributes of a disc filter with exciting new ceramic vacuum technology from Outomec of Finland.

Jan 1, 1991

By C T. Portelli

Belt conveyor transfers are the most likely location for high wear rates and failures. Belt transfers are necessary to change the direction of conveyed material and will remain a part of belt conveyor systems into the future. Burden being accelerated due to fall and changes in direction from one system to the next, prevents steady state flow which introduces component fatigue. The conveyor belt is considered the greatest cost item over the life of a belt conveyor system and consumes considerable downtime to replace, therefore a financial incentive exists to preserve this high-cost item. Other issues created at the transfer include health risks of uncontained dust and product losses due to spillage. Additional consideration to support the belt is one way to improve the life of components and contain dust within the transfer chute. The humble impact cradle/bed has changed little over the years whilst conveyor systems have achieved ever greater flow rates. Further development of the impact cradle is an opportunity to reduce maintenance costs and increase uptime. The peak technology on the market for conventional impact belt support is the dynamic impact cradle, which ensures the belt support area under the chute allows for some dynamic travel, whilst also maintaining a consistent skirt board area. The impact energy at a transfer when installed with Kinder Australia’s dynamic impact belt support system was measured to further understand the forces involved and how they compare with static belt support systems. Adding further dynamic capacity to the load zone has been shown to increase belt life by at least 30 per cent. Other components also benefit from reducing impact energy in the transfer and the incorporation of polyurethane bushes at roller supports has been employed further increase roller and frame life. Kinder Australia has developed a unique and innovative range of belt support technologies that further promote dynamic travel whilst maintaining a consistent skirt board area without a significant increase in belt-friction tension. This technology combines slider rails with rollers that can absorb impact independently within the support system and/or utilising exotic slider materials to overcome high belt speeds and/or system capacities. Kinder Australia has a vast library of documented case studies and application data to ensure the future systems being offered will survive, provide better chute sealing and protect the conveyor belt.

Sep 18, 2023

By Mikula PA

This paper presents the results of in-situ and laboratory investigations into a mining method which utilises conventional continuous mining techniques to carry out two passes in thick coal seams, resulting in the development of stable pillars with relatively small width dimensions and heights up to 6 m. Geotechnical investigations included structural mapping, brightness logging and standard laboratory testing. Virgin stress was measured using overcoring techniques. Two approaches to pillar design were used in the study. These were; pillar design based on empirical formulae and laboratory testing, and pillar disign using calibrated mathematical models. A trial panel was developed at 300 m depth to study pillar deformation and stress changes due to mining. The extent of rib deformation was studied using borescopes and extensometers. In-situ geotechnical measurements were used to calibrate displacement discontinuity and finite element mathematical models of the coal seam. These models were then used to predict the behaviour of a small panel of pillars which were to be developed to 6 m height. The mining method was shown to be feasible provided adequate rib support was installed. The benefit of rib support was found to be two-fold, in that it increased confinement of the pillar in zones of low horizontal stress, while reducing horizontal stress relaxation in zones of high horizontal virgin stress. The possiblity of roof control by designing the small pillars to yield on retreat is discussed.

Jan 1, 1986

By Hunter W. H, Wilson I. P, Craig R. W

In September 1988 the Imperial Smelting zinc - lead blast furnace at Avonmouth England, was uprated from its then 52 week annual rated capacity of 90 000 tonnes/year of furnace zinc to 110 000 tonnes. In order to provide sufficient extra feed the sinter plant was likewise uprated in April 1989 by increasing the blowing rate of the sinter/acid plants from 100 000 to 120 000 Nm3/h, effectively a 20 per cent increase. In the 12 months after the uprate zinc production was only 85 000 tonnes. Two years after the uprate zinc production had increased to 100 000 tonnes, but it was not until January 1992 that a rolling 12-month zinc production of 110 000 tonnes was consistently achieved. This paper describes the problems encountered with the uprate and how they have been or are being overcome. It deals chronologically with events starting with the restart of the ISF at the end of 1988 and covers the following issues and their resolution: 1. Initial shortages of sinter due to an offset in uprate timing. 2. Greater difficulties in operating the larger furnace particularly on start-up, the greater tendency for iron production and serious slagging problems. 3. Coincidental timing of deleterious trends in slag chemistry. 4. Refractory problems in the furnace shaft and condenser. 5. Shortages of sinter due to commissioning problems with the wet gas and sinter tip end fans, and difficulties in obtaining sufficient sinter hardness. 6. Unrealised full benefits of the sinter-acid uprate due to a late change in design to dispense with sinter gas recirculation, but offset by successful use of oxygen. In a planned maintenance stop in September 1992 further improvements to the furnace design were carried out to resolve the refractory problems, and with improvements to the sinter plant the furnace zinc output capacity is planned to rise to a rate of 120 000 tonnes/year within two years.

Jan 1, 1993

By R Mann, R Prasad, S Vink, V Nanjappa

The level of salinity that various aquatic organisms can tolerate without incurring any adverse effects is dependent on several environmental and evolutionary factors. These factors include the relative concentrations of different types of dissolved salts in the water that makes up their habitat, the regimes to which organisms are exposed to waters of differing salinity levels (including naturally derived variations), the degree to which an organismÆs life history stages have adapted to salinity, an organismÆs ability or behaviour to avoid adverse levels of salinity and an organismÆs capacity for osmoregulation.Release of saline water into rivers of the Fitzroy catchment has created concern about the impact on aquatic organisms. Not only is salinity itself a stressor on organisms but different ionic compositions will moderate the effects. Ecotoxicology experiments were conducted using artificial saline water based on mine water chemistry using sensitive macroinvertebrates collected from the catchment, as well as a range of laboratory organisms in accordance with the ANZECC and ARMCANZ (2000) guidelines. The 95 per cent ecosystem protection value calculated from species sensitivity distribution derived from the commercial tests was estimated to be ~2.0 mS/cm. For the protection of 99 per cent of the species the salinity has to be reduced by more than 50 per cent to 0.91 mS/cm. The electrical conductivity (EC) values, derived by commercial testing and species sensitivity distribution in this study suggests that salinity contaminant trigger values previously developed using a referential approach for protection of aquatic ecosystems from saline mine water releases in the Fitzroy may be conservative.CITATION:Vink, S, Mann, R, Nanjappa, V and Prasad, R, 2013. Determining the impacts of salinity on freshwater organisms, in Proceedings Water in Mining 2013 , pp 149-154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Brown N. R

This paper attempts to highlight some of the problems encountered in the economic exploitation of the deeper coal seams by opencast mining methods. The major cost elements of three methods of overburden removal are examined in relation to the overall cost of winning coal from deeper-lying coal seams. The three overburden removal methods examined are dragline stripping and two systems combining dragline stripping with shovels and trucks at varying depths of overburden. A dragline is, undoubtedly, the most cost effective system of overburden removal for depths of up to 30 metres but it is suggested that, when dealing with incremental overburden depths in excess of 30 metres, engineers should consider carefully the possibility of using a shovel and truck operation, or other system, to augment the use of a dragline.

Jan 1, 1986

By R Kroukamp, G Rech

CRONIMET Australia in cooperation with Speciality Metals International, the mining lease holder of the Mt Carbine Tungsten mine, have demonstrated the preconcentration and processing of large (>12 million tonnes) tailings and mine waste dumps on site in far north Queensland. The first stage of this project has proven the economic viability of preconcentration using sensor-based particle sorting whilst ensuring high recovery of industry critical tungsten minerals – wolframite and scheelite. Sensor-based sorting technology have enabled the production of a sorter product to feed the existing wet gravity plant ensuring higher recoveries and increasing concentrate production. Processing of 1,000 tonne low grade samples using the TOMRA x-ray transmission (XRT) ore sorter installed on site, has reduced the volume of material entering the downstream wet processing plant by up to 60%. The sorted 10-25mm size range produced the highest upgrade ratio (product/feed) of 24:1 and achieved sorter concentrate grade of 1.52% WO3, sorter waste grades below 0.014% WO3 and metal recoveries of up to 93.4%. The appropriately sized, barren sorter waste material is also sold as aggregate and other quarrying products and thus adding to the overall economic benefit of the project. The utilisation of the sorting technology on site has produced an economically viable project, significantly reduced capital cost, and reduced the time to market of the final tungsten concentrate. The next phase of the project includes design and installation of a larger two sorter plant capable of over 150t/h feedrate.

Nov 10, 2020

By T Kilpatrick

Managing heat stress on Australian mine sites is a complex and enduring challenge due to the combined and variable contribution of environmental conditions, physical activities, and protective equipment. Inappropriately managed, heat stress can place significant physical strain on workers, leading to serious and chronic health issues. Additionally, excessive heat stress can dramatically reduce productivity, with 30 per cent of workers reporting a loss of productivity due to occupational heat strain. In Australia, due to increased absenteeism and reduced work performance, heat strain is estimated to have an annual economic burden of over $8 billion.

May 5, 2022

By J P. Evert

Didipio gold-copper mine operation is situated in the island of Luzon, approximately 270 km north of Manila in the Philippines, in an area of high seasonal rainfall. The hydrogeological water flow model implied that there would be high connectivity between regional structures and underground operations. This model predicted that underground mine groundwater inflows were expected to quickly rise as the decline progressed to a peak of 510 L/s. Designing a capital pump station to deal with 510 L/s has its own challenges, however developing the decline down to the required level, always dealing with 300 L/s of water and constructing the pump station is extremely challenging and required a robust water management plan and mine design. When dealing with expected high volumes of water, underground mine design and scheduling plays a key role in protecting electrical infrastructure, equipment, secondary pumps, and the decline from flooding. A good drainage system and controlled dewatering plan is essential for safety and progress. This paper details the dewatering techniques and mine designs required to accomplish decline development with high water inflows as used in the Didipio project. It will describe the learnings and outcomes that are achievable with a flexible design, as new structures are mapped, and water intersections are increased. It also highlights the potential for adaptability in mine planning to provide evolving improvements or to evade problems that are expected from the constant reconciliation of data recorded during development.

Mar 29, 2023

By M Pyle, R Ch, T Vizcarra, ramohan, G Lane, G Ballantyne

Preconcentration, through gravity separation (Wallace et al, 2015), magnetic separation and particle size (Clout, 2013), has been used in many historical projects to convert low grade material into ore. More recently, pre-concentration technologies such as bulk sorting (Kurth, 2017), screening (Bearman, 2014) and coarse particle flotation (Vollert et al, 2019) have also demonstrated their ability to progressively reject waste through the value chain. These technologies can not only deliver stepchange improvements to the economics of mining operations, but can transform the environmental and social aspects by minimising water and energy consumption and significantly reduce the quantity of fine tailings produced. However, implementing progressive waste rejection requires technologies and approaches to be combined and applied in the right way to capture the value. From a technical perspective, progressive waste rejection introduces challenges related to the orebody, equipment performance, engineering and understanding the value chain from the resource through to final product. From a management perspective, the key issues are related to people and processes, in particular; motivating the business, challenging the paradigms, and introducing new ways of operating within the constraint of existing management structures to manage risks and minimise lost opportunity costs. This combination of technical and management issues means that progressive waste rejection is a complex undertaking for mining companies, yet the reward for the business and other stakeholders is potentially high and should not be ignored. This paper presents how progressive waste rejection can offer step-change improvements to the business case for high and low grade greenfield and brownfield projects based on case studies completed by Ausenco. The paper then outlines different implementation approaches from concept studies to execution to address the various technical and management challenges outlined above.

Nov 10, 2020

The development of present methods of pillar extraction has evolved from the very earliest of hand mining operations which were limited in scope by venti- lation and transport considerations. Conservation and safety considerations also have led to the current shortwall operations with conventional equipment and powered supports. The shortwall methods have had significant effects on safety, costs, con- servation, flexibility, and other aspects of pillar extraction. The present stage falls short of the ideal but is some guide to prediction in what direction may lie the ideal methods for the future.

Jan 1, 1974

Gold mineralisation was first noted in 1983 at the Wapolu Point area of Fergusson Island, Papua New Guinea (PNG) during a follow-up regional reconnaissance program. Subsequent exploration programs through to late 1987 completed 22,147m of costean trench sampling, 553 aircore/RC/diamond core drill holes (16,970.5m total) and metallurgical testwork, predominantly on the Wapolu grid in two mineralised areas.Subsequently in 1988, geostat-istical global and polygonal resources were calculated for the main mineral-ised zones, Didigayagaya and Dagwalala. In 1992, a 'probable total reserve' of 1.9Mf @ 2.4g/t with a 1.2g/t cut-off was calculated for these prospects.

Jan 1, 1994

By Emerson J

Drilling has always been one of the most important parts of the exploration process with most companies spending around 25% of their budget on drilling. Although superficially there appears to be little difference in drills and drilling practice a number of major refinements have taken place over the last decade that have significantly changed the drilling scene. One of the most important advances has been in hydraulic engineering giving rise to the Dual Purpose top drive drilling rigs. These have led to significant productivity increases with the high rotation speeds and longer fleets. Downhole technology has also advanced with better hammers, stronger drill rods, impregnated coring bits and improved drilling fluids. Although geologists continue to measure drilling performance on a cost per metre basis, greater consideration is at last being paid to the quality of sample produced. This is particularly the case with RC drilling where quite sophisticated automatic and semi automatic splitting devices have been developed. Drill operators are now required to be experienced in both Diamond coring and air drilling and be better qualified to maintain the more sophisticated machinery. Management of drilling companies or drilling divisions has also had to change to accommodate both the high capital cost of equipment and the demands of keeping drilling a cost effective exercise.

Jan 1, 1987

The reduction in the number and duration of machinery and equipment failures is an important source of economical efficiency enhancement in the Polish coal mining industry.Non-dismantling methods have been thus developed to evaluate the technical state of machines. Among these viroacoustical methods are the most effectively employed. Two-directional organisation of the testing can be chosen, such as periodical and continuous inspection. The monitoring methods for ball bearing, rope tension uniformity, longwall shearers, main fans and shafts installations etc. Instrumentation for monitoring measurements are either of intrinsically - safe or explosion - proof construction, which enables using them in a gas-hazard atmosphere. The development of these procedures has led to the trials to insert the diagnostic methods into the organisational scheme of a coal mine.

Jan 1, 1991