Search Documents

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

0. C. Ralston and F. Fraas—Dr. Sun and associates have presented an interesting paper not all of which is comprehended by us. The data assembled measure the deflections of particles in an electrostatic field as a function of a number of independent variables and some dependent variables that are not sharply differentiated. These data are all based on a Johnson type machine of definite, well-described geometry, something not often done in electrostatic separation literature. One new fact brought out by this technique is the effect of coal dust on admixed pyrite and quartz. The effects are opposite in character, as should be expected and we do not agree with the authors that these effects are negligible. Fraas' also used a multiple cell "distribution analyzer" and gives in fig. 5 of his paper a straight line plot with no humps or curves. This is not necessarily at variance with Sun's results because Fraas used a larger gap between electrodes and had no evidence of particles adhering to or dropping off the charged electrode. The section of Sun's paper on effect of surface conductivity contains a speculation that the dielectric constant "represents more or less the electrical conductance of the bulk body instead of the surface of the mineral particles." A simple picture of the meaning of the dielectric constant is that it is the specific inductive capacity of a dielectric when used as the dielectric between the plates of a condenser. It is at once evident that the above speculation confuses capacity with conductance—two definitely independent variables. We ask the authors to state in what group or subdivision their garnet belongs; what method and units were used in calculating the data of col. A, table I and their meaning; what was the temperature of the carrier roll and, finally, has any effort been made to investigate the effects of particle shape on distribution in the electrostatic field? S. B. Hudson—I have read this article with great interest. We have been engaged in research work on the principles of electrostatic separation in this laboratory for some time now, and our findings agree with those of the authors in many respects. The article shows evidence of careful and valuable research in the field of electrostatic separation. A "distribution analyser," very similar to that described in an earlier article by one of the authors," was incorporated in an inclined plate-type electrostatic separator designed and built in the Melbourne University laboratory in 1948 for investigation purposes.22 The actual splitting edges were machined from y! in. per-spex, and the paper hoppers were supported on linen thread immediately below the perspex dividers. These dividers fitted into machined slots in a framework to give accurate Yz-in. spacings. The hoppers (staggered) fed directly into a rack of test tubes, which is supported on a vertical pantograph arrangement. The rack was positioned with guides on the horizontal pantograph stand, and this ensured positive alignment when replacing the rack after making weighings. In later work, when much heavier feed rates were used, of the order of 30 to 40 Ib per in. per hr a rack fitted with rectangular metal containers and similarly aligned was used. Some work was done here on comparing the distributions of minerals when passed separately and when passed as a mixture, and it was found that there was quite an appreciable difference in the two results.= However, in our separator the particles do not pass down the plate in a single layer, and this difference is probably caused by collisions of one mineral particles with the other mineral particles. In most of the investigational work here, the change of the center point of the distribution is measured to establish the effect of a variable, such as voltage. Two minerals (zircon and rutile) have been studied rather exhaustively, and it was found that their distributions are very nearly normal. Owing to the sharpness of the distribution curves, the usual method of obtaining the mean or median was inaccurate, and was not used; instead the mean (also the median), calculated on the assumption of a normal distribution, was used to locate the center point of each distribution and proved satisfactory. The effect of polarity becomes very apparent in the plate-type separator where frictional charges play a very important part when using highly resistive minerals such as zircon. With rutile, a comparatively conductive mineral, polarity of the electrode has little effect. On the other hand, the magnitude of the voltage has a far greater effect on conductive than on resistive minerals. Shiou-Chuan Sun (authors' reply)—Thanks are extended to Drs. Ralston and Fraas for their keen interest in this paper. Their questions concerning coal dust,

Jan 1, 1951

By W. L. McMorris, A. H. Brisse

IN the last several years the coal industry has intensified its effort to solve the growing problem of cleaning and recovering fine mesh coals. On one hand these has been increasing civic pressure for cleaner streams, and on the other hand there has been increasing production of fine mesh coal, resulting directly from adoption of the modern mining methods so essential to the economy of the coal mining industry. Cleaning fine coal with the same precision possible with coarser coals is a difficult task, and for coals finer than 200 mesh it has been impractical. Furthermore, the inclusion of —200 mesh material in the final product markedly increases costs of de-watering and thermal drying, which are necessary steps if coal is to meet market requirements. Consequently these extreme fines have generally been wasted. As a result, problems have been created in many districts because there has not been enough area for adequate settling basins. Wasting of coal in the -200 mesh slimes may account for a loss in washer yield equivalent to 2.0 to 2.5 pct of the raw coal input. With rising mining costs the value of such a loss is constantly increasing and a need for a better solution to the fines problem becomes more pressing every day. From an operating viewpoint, also, continuous removal of extreme fines from the washing plant circuit permits good water clarification practice, improving significantly the overall cleaning efficiency. The obvious desirability of recovering a commercially acceptable coal from washery slimes prompted U. S. Steel Corp. to investigate the merits of the Convertol process developed in Germany." Although this process has been used commercially in Europe for some time, little if any consideration has been given to its possible adoption in the U. S. until very recently. Fundamentals of the Convertol Process: In the Convertol process, droplets of dispersed oil are brought into intimate contact with the solids suspended in the coal slurry to be treated. This contact causes oil to displace the water on the surface of the coal by preferential wetting, or phase inversion, after which the coal particles are allowed to agglomerate in a manner permitting their re- moval from the slurry by centrifugal filtration. The clay and other particles of mineral matter suspended in the slurry do not have the affinity for oil the coal particles have. Consequently the oil treatment is preferential to coal to the extent that more than 95 pct of the oil used reports with the clean coal recovered. Figs. 1 through 3 will clarify the steps involved in the process. Fig. 1 shows the suspended material in the slurry to be treated, which is a thickened product containing 40 to 45 pct solids. Oil is now injected into the slurry under vigorous agitation to produce good oil to coal contact conditions, which result in preferential oiling of the coal particles. These coal particles are then permitted to agglomerate by gentle stirring in a conditioner to form flocs, as shown in Fig. 2. At this point in the process the agglomerated oiled coal can be washed and partially dewatered on a vibrating screen, as shown in Fig. 3. Finally, the washed flocculate can be further dewatered in a high-speed screen basket centrifuge or in a solid bowl centrifuge. Commercial Application of the Convertol Process in Germany: The original Convertol process was developed by Bergwerksverband zur Verwertung von Schutzrechten der Kohlentechnik, G.m.b.H., a German research organization controlled by the Coal Operators Assn. of the Ruhr Valley. The process as reduced to commercial practice in Germany' is shown in Fig. 4. In this process a thickened slurry (40 to 45 pct solids) mixed with a predetermined percentage of oil is fed from a surge tank to the phase inversion mill. After the phase inversion step, the slurry is usually discharged directly to a highspeed screen centrifuge. From 3 to 10 pct oil is used, depending on type of oil, size consist of coal to be recovered, and operating temperature. The top size of fine coal cleaned in Germany by the Convertol process is limited by the size of the openings in the centrifuge screen basket. Any mineral matter coarser than the basket opening, which is generally 60 to 80 mesh, must remain with the oiled coal. If the coal fines have been effectively cleaned down to about 80 mesh, the cleaning performance of the process is practically unaffected by the presence of coarse coal particles. However, since recovery of coal much coarser than 80 mesh is mow economical by conventional methods, it normally becomes more costly to allow substantial percentages of this coarse coal in Convertol process feed. Where the general plant layout does not permit effective cleaning of coal sizes down to 80 mesh or lower. there is some justification for a coarser Con-

Jan 1, 1959

By W. W. Whitaker, C. W. Manry, R. H. McLean

In an eccentric annulus, cement may favor the widest side and bypass slower-moving mud in the narrowest side. Tendency of the cement to bypass mud is a function of the geometry of the annulus, the density and flow properties of the mud and cement and the rate of flow. Bypassing can be prevented if the pressure gradient protluced from circulation of the cement and buoyant forces exceeds the pressure gradient necessary to drive the mud through the narrowest side of the annulus at the same velocity as the cement. In the absence of buoyant forces, one requirement for this balance is maintenance of the yield strength of the cement greater than the yield strength of the mud multiplied by the maximum distance from the casing to the wall of the borehole and divided by the minimum distance. If the yield strength of the cement is below this value, bypassing of mud cannot be prevented unless buoyant forces or motion of the casing significantly aid the displacement. INTRODUCTION Successful primary cementing leaves no continuous channels of mud capable of flow during well treatment and production. Prevention of channels requires care. Tep-litz and Hassebroek provide evidence of channels of mud after primary cementing in the field.' Channeling of cement through mud in laboratory experiments has also been reported.'-' Recommendations for improving the displacement of mud include (1) centralizing the casing in the borehole,'-" 2) attaching centralizers and scratchers to the casing and moving it during displacement,18 "3) thinning the isolating the cement by plugs while it is circulated down the casing,%( (5 establishing turbulence in the cement," and (6) holding the cement slurry at least 2 lb/gal heavier than the mud and circulating the cement slurry at a very low rate of flow.' Although much has been written about the above parameters, the relative importance of each has not been well defined. In this investigation, the mechanics of mud displacement are described through results from analytical models and experiments. The model chosen — a single string of casing eccentric in a round, smooth-walled, impermeable borehole — is analagous to casing centralized in a borehole which is not round and to placing more than one string of casing in a borehole. In each, some paths for flow are more restricted than others. A fluid flowing in the borehole may seek the least restricted, or most open, path. This tendency for uneven flow can lead to channeling of cement through mud unless preventive measures are taken. The analytical models describe channeling and give means of balancing the flow. Experimental data test the analytical models and illustrate effects of motion of the casing, differences in density and mud's tendency to gel. Results are encouraging. Piston-like displacement of mud by an equal density cement slurry is possible through proper balance of the flow properties of the mud and cement slurries to the eccentricity of the annulus. The more eccentric the annulus, the thicker must be the cement relative to the mud. If proper balance is not achieved. bypassing of mud by cement cannot be prevented without assistance from motion of the casing or buoyant forces. Increasing the rate of flow can help to start all mud flowing but cannot prevent channeling of cement through slower moving mud in an eccentric annulus. Thinning the cement slurry tends to increase channeling although the extent of turbulence in the annulus may be increased. Description of flow in an eccentric annulus begins in the next section. It is assumed that (1) the casing is eccentric and is stationary, (2) the mud and cement slurries have the same density and (3) the gel structure of the mud has been broken and the mud and cement follow the Bingham flow model. Effects related to these restrictions will be discussed. FLOW PATTERNS SlNGLE FLUID IN ANNULUS Flow of a single fluid through an eccentric annulus is illustrated in Fig. 1. Part A shows laminar flow of a Newtonian fluid. This distribution of flow was calculated by Piercy, Hooper and Winney.' In fully developed turbulent flow, the velocity distribution around the annulus is less distorted, but the flow still favors the widest part of the annulus Parts B, C and D of Fig. 1 are a qualitative representation of the flow of a Bingham fluid. The yield strength of the fluid increases the severity of bypassing compared to Newtonian flow. At a very low rate of flow, all flow is confined to that portion of the annulus which has the minimum perimeter-to-area ratio. The fluid shears on the perimeter of that area when the pressure gradient multiplied by the area just exceeds the yield stress of the fluid multiplied by the perimeter. Whether or not the minimum perimeter-to-area region encompasses all of the annulus or only a part (as shown in Part B) depends on the geometry of the annulus. If only a part begins to flow, increasing the rate of flow increases the area flowing until finally there is flow throughout the annulus.

By R. T. DeHoff

In any structural transfortnation which is driven by surface tension, the geometric variable of fimdamental importance is the local value of the mean surface curvatuve. Acting through the suvface free energy, this quantity determines the magtnitude of both the pressure and the chemical potential that develops in the neighborhood of an arbitrarily curved surface. A metallographic method which would permit the quaniitatiue estinzation of this propevty is of fundarnerztal irztevest to studies of such processes. In the present paper, it is shoun that the average value of the mean surface curvature in a structuve can be estimated from two simple counting measuretnents made upon a vepresentative metallograpIzic section. No simplifyirlg geonzetric assurmptions are necessary to this deviuation. It is further shoum that the result may be applied to parts of interfaces, e.g., interparticle welds in sintering, or the edge of growing platelets in a phase transformation, without loss of validity. In virtually every metallurgical process in which an interface is important, the local value of the mean surface curvature is the key structural property. This is true because the mean curvature determines the chemical potential of material adjacent to the surface, as well as the state of stress of that material. The theoretical description of such broadly different processes as sintering,1,2 grain growth,3 particle redistrib~tion4,5 and growth of Widmanstatten platelets8 all have as a central geometric variable the "local value of the mean surface curvature". The tools of quantitative metallography currently available permit the statistically precise estimation of the total or extensive geometric properties of a structure: the volume fraction of any distinguishable part:-' the total extent of any observable interface,10,11 and the total length of some three-dimensional lineal feature:' and, if some simplifying assumptions about particle shape are allowed, the total number of particles.'2"3 The size of particles in a structure, specified by a distribution or a mean value, can only be estimated if the particles are all the same shape, and if this shape is relatively simple.14-16 The relationships involved in converting measurements made upon a metallographic section to properties of the three dimensional structure of which the section is a sample are now well-established, and their utility amply demonstrated. In the present paper, another fundamental relationship is added to the tools of quantitative metallography. This relationship is fundamental in the sense that its validity depends only upon the observation of an appropriately representative sample of the structure, and not upon the geometric nature of the structure itself. It involves a new sampling procedure, devised by Rhines, called the "area tangent count". It will first be shown that the "area tangent count" is simply related to the average value of the curvature of particle outline in the two-dimensional section upon which the count is performed. The average curvature of such a section will then be shown to be proportional to the average value of the Mean surface curVature of the structure of which the section is a sample. The final result of the development is thus a relationship which permits the evaluation of the average value of the mean surface curvature from relatively simple counting measurements made upon a representative metallographic section. The result is quite independent of the geometric or even topological nature of the interface being studied. QUANTITATNE EVALUATION OF AVERAGE CURVATURE IN TWO DIMENSIONS The Area Tangent Count. Consider a two-dimen-sional structure composed of two different kinds of distinguishable areas (phases), Fig. l(a). If the system is composed of more than two "phases", it is possible to focus attention upon one phase, and consider the remaining structure as the other phase. The reference phase is separated from the rest of the structure by a set of linear boundaries, of arbitrary shapes and sizes. These boundaries may be totally smooth and continuous, or piecewise smooth and continuous. An element of such a boundary, dA, is shown in Fig. l(b). One may define the "angle subtended" by this arbitrarily curved element of arc, dO, as the angle between the normals erected at its ends, Fig. l(c). Now consider the following experiment. Let a line be swept across this two-dimensional structure, and let the number of tangents that this line forms with elements of arc in the structure be counted. This procedure constitutes the Rhines Area Tangent Count. Suppose that this experiment were repeated a large number of times, with the direction of traverse of the sweeping lines distributed uniformly over the semicircle of orientation.' Those test lines which ap- proach from orientations which lie in the range O to O + dO form a tangent with dA; those outside this range do not, see Fig. l(c). Since the lines are presumed to be uniformly distributed in direction of traverse, the fraction of test lines which form a tangent with dA is the fraction of the circumference of a semicircle which is contained in the orientation range, dO; i.e., vdO/nr or dB/n. If the number of test lines is N, the number forming tangents with dA is N(d0/n). Since each test line sweeps the entire area of the sample, the total area traversed by all N test lines is NL2. The number of tangents formed with dA, per unit area of structure sampled, is therefore

Jan 1, 1968

By R. A. Burmeister, G. P. Pighini, P. E. Greene

An open tube vapor phase epitaxial growth system has been used for large area (multiple substrate) growth of GaAs1-xPx on GaAs substrates. The GaCl-GaCl transport reaction is used with either a GaAs or Ga (nonsaturated) source. Selenium and tellurium have been used for donor impurities, and zinc as an acceptor. The useable substrate area in this system is approximately 20 sq cm. The uniformity of thick-ness of the epitaxial layers are typically better than ±5 pct across a given wafer. Electrical and optical measurerments indicute comparable uniformity in electrical and luminescent properties within a wufer. The application of this system to the large scale pro-duction of GaAs1-x Px for display devices, both discrete and arrays, is discussed. Typical electrical and luminescent properties of light emitting diodes fabricated front material produced by this technique are presented. THE most promising materials currently being utilized for visible injection electroluminescence are GaAs1-xPx, Ga1-xAlxAs, and Gap. All have reasonably efficient emissions in the red portion of the visible spectrum at room temperature; Gap also has an efficient green emission.' At present, GaAs1-xPx has a technological advantage over Ga1-xAlxAs and Gap for display applications, since relatively large (several sq cm) areas of GaAs1-xPx suitable for use in electroluminescent devices may be readily grown by vapor phase growth techniques. In contrast, the preparation of Gap and Ga1-xAlxAs for electroluminescent device applications generally employs solution growth techniques which are at present not well suited for the growth of large areas of uniform thickness and doping level. The capability of uniform growth over large substrate areas and the use of multiple substrates is necessary for the practical utilization of electroluminescent devices. This is particularly important when quantity production or monolithic devices are required. Furthermore, in many display applications arrays of light emitting devices are used, the individual elements of which are of a size resolvable by the unaided eye. Thus the overall dimensions of display are substantially larger than those of most semiconductor devices. It is also necessary to achieve a high degree of control over the growth parameters to attain the required degree of reproducibility of materials properties for electroluminescent devices. In the case of GaAs1-xPx it is necessary to accurately and precisely control the phosphorus content of the alloy, both on a macroscopic and microscopic scale, in addition to the parameters generally associated with epitaxial growth such as thickness and doping level. This value is critical, as it has a major effect on the performance of electroluminescent devices. This paper describes the epitaxial growth of GaAsl-xPx suitable for electroluminescent display devices using a system developed specifically for this purpose, and which contains several novel features. The results of studies of selected physical properties of the epitaxial layers are also discussed. Finally, a brief summary is given of the characteristics of display devices fabricated from GaAsl-xPx grown in this system. EXPERIMENTAL A) Reactants. A number of techniques suitable for the vapor phase epitaxial growth of GaAs1-xPx have been reported in the literature.'-' The method selected for this investigation is that in which the Ga is transported by the GaC1-GaCI3 reaction in an open tube process. The results reported here were obtained using either the combination of GaAs, AsC13, and pH3, or Ga, AsH3, pH3, and HC1 as the initial re-actants.* The ASH3 and pH3 were obtained as dilute *Several different sources of supply were used for these reactants, y~elding comparable results._____________________________________________________ mixtures in HZ; the HC1 was obtained from the reduction of AsC13 by Hz at elevated temperatures. Both selenium and tellurium were employed as donor impurities, and zinc as an acceptor impurity. Selenium was introduced in the form of H2Se, tellurium in the form of tellurium-doped GaAs, and zinc in the form of diethy1 zinc. B) Apparatus. The prinicipal difference between the apparatus used in the present study and that of Tietjen and Amick,8 in addition to size and other related design features, is that RE induction heating is utilized in place of resistance heated furnaces. Induction heating was selected for this application because it appears to have several advantages, including: 1) It is possible to keep all fused silica portions of the apparatus at temperatures well below those of the reaction zone, thus minimizing a possible source of contamination. 2) The thermal mass of an induction heated system can be made small, thus reducing the total time required for the growth process. 3) Sharp temperature profiles (desirable for high deposition efficiency) are easily achieved. 4) The volume of the system for a given substrate area can generally be made smaller than a comparable resistance heated unit. This results in shorter time

Jan 1, 1970

By F. W. Schremp, J. W. Chittum, T. S. Arczynski

This paper describes a laboratory study of causes of external casing corrosion and the test work that led to the use of oxygen scavengers to prevent this attack. External casing failures are classified as water-line, casing-casing, collar and body failures. A corrosion mechanism based on principles of differential oxygen availability is developed that is consistent with facts known about each kind of failure. The field use of oxygen scavengers is depicted as a direct result of the laboratory study. A part of the paper is devoted to reporting on the field use of hydra-zine to control external casing corrosion. Results of field measurements made over a period of several years are presented as evidence of the efectiveness of the hydrazine treatment. The first conclusion reached is that the use of hydrazine materially reduces the cathodic protection requirements for treated wells. This result is interpreted to mean that a reduction is taking place in the amount of corrosion on the casing. Results indicate also that hydrazine shows its greatest usefulness within the first 12 to 18 months after a well is completed when pitting corrosion is likely to be most active. INTRODUCTION According to surveys sponsored by the National Association of Corrosion Engineers,' the cost of repairing casing leaks caused by external corrosion may exceed $4 million per year. In addition, well damage and lost production resulting from casing leaks probably costs the petroleum industry an additional $5 to $6 million per year. Concern about the cost of external casing corrosion led to an extensive laboratory study of factors causing this external corrosion and to the development of a new approach to its prevention. This paper presents a discussion of various causes of external casing corrosion, details of laboratory studies and the results of the field use of an oxygen scavenger in well cementing fluids to prevent the external corrosion of oil-string casing. Measurements on test wells over a period of several years show that cathodic-protection current requirements are greatly reduced when hydrazine is used in cementing mud. Reduction of current requirements can be interpreted to mean that removal of oxygen by hydrazine has greatly suppressed corrosion cells on the external surface of the casing and thereby, has reduced corrosion. To date, hydrazine has been used by the Standard Oil Co. of California in more than 200 well completions. KINDS OF CASING FAILURES A survey of a large number of casing leaks disclosed four types of external casing failures — water-line, casing-casing, collar and body failures. These types are identified largely by their location on the casing. Water-line failures are found just below the surface of water or mud in the casing annulus. Casing-casing failures occur on the oil string just below the shoe of the surface string. Collar failures are found in the threaded ends of casing joints where they are screwed into casing collars. Body failures may occur at any point on the body of a casing joint. Ex- amples of each kind of failure have some of the general characteristics that are shown in Fig. 1. Water-line failures usually result in the circumferential severance of an oil-string casing. The corrosive action causing a water-line failure usually is sharply defined and is limited to a short length of the casing. Casing-casing failures usually are accompanied by pitting corrosion distributed around the oil-string casing for distances up to 100-ft below the shoe of the surface string. Casing-casing failures may also sever the casing. Collar failures seem to start on the first thread at the bottom of recesses between collar and casing joint. Corrosion proceeds across the threads by what appears to be a normal pitting mechanism. Both casing and collar are severely attacked. Body failures are the result of highly localized pitting at any point on a casing wall. Besides the pit that perforates a casing, a large number of other pits usually are found along one side of the casing joint. The pits occasionally are filled with corrosion products consisting largely of oxides and sulfides.' Frequently, the mill scale is largely intact on the rest of the casing. Examination of a casing failure does not always reveal the cause of the failure. Frequently, the necessary details are destroyed when the failure occurs. For example, formation water flowing through a perforation at high velocity may enlarge the hole and destroy any remaining evidence of the cause of the failure. One way to obtain undistorted information about a failure is to study the nature of other pits on the casing in the vicinity of the failure. A study of such pits frequently suggests that they are characteristic of an attack resulting from the differential availability of molecular oxygen.

By K. Prins

ONE of the more pressing problems faced by the coal industry today is the development of adequate means for meeting conservation laws, particularly those involving stream pollution, in various parts of the country. Discharge of dirty coal washery water into streams and rivers is almost universally frowned upon. Many states have enacted laws carrying heavy fines to curb the practice. The Prins stream-cleaner is one of the latest machines to enter the market. It is closely related to the cyclone thickener in principle. Eleven stream-cleaners are currently operating, ranging in size from 4 to 16 in. diam. In more recent installations the water enters directly in line and on a tangent with the impeller. The impeller consists of a vertical shaft up through a packing gland and bearings, and a V-belt pulley. The lower part is a tubing fastened to the shaft above, extending through the water intake compartment and provided with six vertical flat bars welded to the tubing. Portholes are situated in the upper end of the tubing, immediately below the point where shaft and tubing join together. The portholes are placed so that they are in open communication with the upper compartment of the stream-cleaner from which the processed water is discharged. The impeller is motor driven with a wide range vari-pitch drive employed between motor and impeller. The motor is mounted vertically, and the mounting provided with a vertical hinge allowing for needed adjustment of the wide range vari-pitch drive. The dirty coal washery water entering the machine under 20 lb psi pressure, flows from the compartment above the impeller, between the impeller blades, and is whirled around in the vertical section of the impeller enclosure. The speed of the impeller supplies centrifugal force and velocity required for separating suspended solids from water. The lower part of the machine consists of a cone, whose action is similar to other machines of the same type. The underflow discharge orifice is a cold rolled steel block machined to correspond with the cone angle and allows insertion of steel tubes of different diam. On 16 in. machines a 1 ¾ in. ID vertical discharge pipe is used. Provision is made for attaching a curved section of the same diam to the vertical pipe, to which, in turn, different lengths of horizontal pipe can be connected. Curved Pipe Advantageous It has been found that a curved pipe offers resistance to discharged material flow. In addition, the rotary motion of the underflow can be easily arrested in a curved pipe. Impeller speed of the 16 in. diam machine is provided from 400 to 800 rpm. A speed of about 474 rpm is suitable for maintenance of a constant underflow in coal slurry. In one installation 5x ¼ in. coal is cleaned in a Jeffrey Baum type washer at a 225 tons per hr rate. Washer installation is of the conventional type and a drag type sludge tank is used for water clarification purposes. Capacity of the water system, including the Baum washer, is about 40,000 gal. Before placing the stream-cleaner in operation, it was necessary to flush out the entire system every five days of two shift operations. The only time the system is drained now is for repair work on the sludge conveyor or the rig. The suction line of the stream-cleaner pump terminates in a number of small branch lines located at a depth of about 4 ft above the sludge conveyor. Each branch line extends the full width of the tank and is provided with four intake ports, each one with a funnel shaped inlet projecting downward. The arrangement provides an extensive pick-up area, for dirty water, and the inlets are arranged for a low rim velocity, preventing the taking in of coarse particles. The funnels are also arranged to extend up or down in the tank. They are set to pick up -60 mesh material exclusively.' The material is a high ash and high sulphur product and thus has to be disposed in the refuse conveyor. The underflow of the stream-cleaner is discharged on top of the washery refuse which is carried in a drag type horizontal conveyor, discharging into another refuse conveyor inclined at 30º with a short horizontal loading section. Some Disadvantages The impeller inherits certain disadvantages because of the nature of its construction. Additional moving parts make it subject to wear and maintenance costs. The advantage of being able to maintain a constant speed, however, to produce desired water velocity in the machine outweighs the drawbacks. Better separation between water and solids can be obtained by regulating time of residence of water through adjustment of valves in the intake and discharge lines. The amount of fines encountered during plant operation will vary because of higher or lower moisture in coal passing over fine coal vibrating screens. Even the amount of fines picked up by underground loading machines will be inconstant. Consequently, the percentage of solids will vary in water to be processed. The velocity in the feedlines to the slurry thickeners will fluctuate, with the required water velocity lacking. Another advantage advanced for the machine is its ability to operate on 15 to 25 lb line pressures at the water intake, reducing pump power required and pump maintenance.

Jan 1, 1952

By R. T. Hukki

John F. Myers (Consulting Engineer, Greenwich, Corm.)—Since the art of comminution has lain practically dormant for many years, it is very interesting that R. T. Hukki approaches the subject with a new concept. One is reminded of the research carried on by A. W. Fahrenwald of Moscow, Idaho, a few years ago. Fahrenwald mounted a steel bowl on a vertical shaft. The balls and ore placed in the bowl were rotated at fast speeds, thus simulating the supercritical speeds used by Hukki. The rolling action of the balls against the smooth shell liner has pretty much the same effect. The action is horizontal in one case and vertical in the other. Both researchers report good grinding activity. It is also constructive that such able investigators give to the students of comminution their interpretation of their laboratory results in terms of large-scale operation. History shows that it takes a lot of time for such radically new ideas to be absorbed by the industry. Typical of this is the present-day activity of cyclone classification in primary grinding circuits. The idea of cyclone classification has been kicking around for 30 or 40 years. Certainly we all suspect that the ponderous grinding mills of today, and their accessory apparatus, large buildings, etc., will ultimately give way to small fast units, just as this has occurred in other industries over the past 50 years. At the moment there is no evidence that ball and liner wear is prohibitively high. In fact, at the time Fahrenwald was demonstrating his high-speed horizontal machine at the meeting of the American Mining Congress, several years ago, he assured this writer that the balls retained their shape much longer than they do in conventional tumbling mills. Rods and balls that slide (as some operators in uranium plants are experiencing) get flat. Apparently the balls have a rolling action. Mr. Hukki's references to the processing capacity of the Tennessee Copper Co. mills is adequate. Those studying this subject will be greatly interested in the paper presented by Richard Smith of the Cleveland-Cliffs Iron Co. at the annual meeting of the Canadian Institute of Mining and Metallurgy in Vancouver April 24, 1958. This paper will be published during the latter part of 1958 in the Canadian Institute of Mining and Metallurgy Bulletin. Hukki's pioneering spirit is to be commended. R. T. Hukki (author's reply)—It has been heartening to read the objective discussion by J. F. Myers. The sincerity of his opinions is further strengthened by the fact that the article he has discussed contradicts in a major way the parallel achievements of his life work. Myers is right in his opinion that in general it takes a long time before new ideas are accepted by the industry. On the other hand, revolutions usually take place at supercritical speeds. There are many indications at present that both the unit operation of grinding and the related subject of size control are now just about ripe for a revolution. In grinding, brute force must ultimately give way to science. Rapid progress can be anticipated in the following fields: 1) Autogenous fine grinding at supercritical speeds will be the first advance and the one that will gain recognition most easily on industrial scale. At this moment, little Finland appears to be leading the world. Crocker recently made a statement that in nine cases out of ten, your own ore can be used as grinding medium more effectively and far more economically than steel balls. This is true. The present author would like to introduce a supplementary idea: In eight cases out of the nine cited above, it can be done at the highest overall efficiency in the supercritical speed range. Fine grinding must be based on attrition, not impact. The path of attrition may be vertical, horizontal, even inclined. 2) In coarse grinding, the conventional use of rods is sound practice. However, even the rods can be replaced by autogenous chunks large enough to offer the same impact momentum as the rods. To obtain the momentum, the chunks must be provided with a free fall through a sufficient height in horizontal mills operated at supercritical speeds. Coarse grinding must be based on impact. Detailed analysis of the subject may be found in a paper entitled "All-autogenous Grinding at Supercritical Speeds" in Mine and Quarry Engineering, July 1958. 3) All conventional methods of classification, including wet and dry cyclones, are inefficient in sharpness of separation. Continuous return of huge tonnages of finished material to the grinding unit with the circulating load is senseless practice. In the near future the present methods will be either replaced or supplemented by precision sizing. These three fields are also the ones to which J. F. Myers has so admirably contributed in the past. Fine Grinding at Supercritical Speeds. By R. T. Hukki (Mining EnGineERInG, May 1958). Eq. 9, page 588, should be as follows: T , c, (a — 6') n D Ltph On page 584 of the article the captions for Figs. 4 and 5 have been placed under the wrong illustrations and should be interchanged.

Jan 1, 1959

By M. V. Lowry

This paper outlines the economic considerations that led to the recent installation of a thickener at St. Joseph LeadCo.'s Balmat, N.Y. mill. To incorporate storage of concentrates, they decided upon a single, unusually deep tank to be used for both storage and thickening. The abnormally high rake lift required was achieved by the novel feature of having the entire drive platform raise and lower. Initial operating problems are described along with the satisfactory solutions. Total costs for concentrate handling before and after installation of the storage thickeners are compared. In Northern New York State, the St. Joseph Lead Co. conducts a 2100 tpd zinc mining and milling operation at its Balmat Plant. Conventional crushing, grinding, and flotation is used to produce a zinc concentrate. For 32 years, from 1930 through 1962, the plant operated with the concentrates going directly from flotation to the filtering, drying, and loading facilities. All of the concentrate handling equipment, therefore, had to operate 24 hrs per day. It also had to accommodate wide fluctuations in tonnage, due to variations in the grade of ore. Many problems were thereby encountered in filtering and drying, but it was never concluded that the cost could be justified for installing a conventional, large diameter thickener. Finally, in 1963, they installed an unconventional thickener that is unusual in several respects. The tank depth is 16 ft instead of the normal 8 ft. The rakes are raised and lowered by having the main drive gear located on a movable platform. Automatic controls are programmed to raise the drive platform and rakes during one shift of storage. During the next two shifts of withdrawal, the controls are programmed to lower the drive platform and rakes. After three years of operating this unique storage-thickener, the conclusion is that a correct choice was made from several alternative schemes for storing concentrates. The various considerations involved in the final selection will here be analyzed, and the design features and installation details will be de- scribed. Operating problems and modifications made to the equipment will next be considered, and finally the effects upon filtering, drying, and loading will be reported. SELECTION CONSIDERATIONS Even without a thickener, concentrate handling had become reasonably efficient at the Balmat Mill by the year 1962. A tonnage that varied between 6 and 25 tph was being handled fairly satisfactorily. The filter cake moisture of 8%% seemed quite respectable, except that two large filters were usually in service. Three filters often had to be operated in order to prevent excessive filter overflow with consequent loss of values. This situation occurred when zinc concentrates from flotation exceeded 20 tph and when filter cloth blinding developed. Over the years, numerous small improvements had been effected, such as: selection of a filter cloth with better flow characteristics; addition of flocculant to the filter feed; and, in 1953, the smallest of three drum filters was replaced by a five disc, 8' 10" diam filter with a bottom agitator and snap blow. As another example of fairly efficient operation, the oil-fired dryer was doing a seemingly satisfactory job of further reducing the moisture content to an average of 3%. However, there were often considerable dust losses when the tonnage suddenly dropped off to 6 tph. At high tonnage rates, the resulting high moistures of 4% and 5% caused difficulties due to concentrates sticking and freezing in chutes leading to the box car loaders. (Drying of concentrates is justified because of the high freight rate for the long shipping distance to the company owned smelter at Josephtown, Pa. near Pittsburgh.) It was long realized that installation of a thickener would permit the subsequent steps of concentrate handling to proceed more smoothly and would alleviate the problems existing in the filtering, drying, and loading operations. It was also realized that even a slightly lower filter cake moisture could mean considerable savings in fuel oil. However, all these factors were never quite sufficient to warrant the expense of a thickener until three more considerations were added to the picture. First, the advent of flocculants meant that a thickener of relatively small area could now be considered. Secondly, a complete renovation of the zinc flotation circuit was made between 1957 and 1961. The

Jan 1, 1967

By B. H. Kear, S. M. Copley

Stress-stvain curves are presented for Ni3Al (y') cvystals in several ovientations, deformed in tension and compression at constant displacement rate, at temperatures from 70° to 2000°F. Both the yield stress and wovk havdening increase with temperature, with the magnilude of the effect dependent on ovientation. The yield stress maximum occurs at 1500°F in [001], at 1400°F in [011], and at 1200°F in [111]. The suppression of the yield stress peak in [011] and [111] orientatiorzs is due to the onset of cube slip, rather than octahedval slip, a1 elerated temperatures. The temperature and orientalion dependence of work hardening in nominal single slip orientations corvelates with changes in the CRSS ratio for octahedral slip and cube slip, in agreement with a model for work hardening based on pinning of screw dislocalions by cross slip from an octahedral plane into a cube plane. It is concluded that the unique plastic properties of y' have a decisive influence on both ductility and strength characleristics of y +y' nickel-base superalloys. It has long been recognized that the strength of y + y' nickel-base superalloys depends on the precipitation of the y' phase [basically Ni3(Al,Ti)]. This paper presents new data on the strength characteristics of single crystals of simple y' (Ni3Al), and forms the first step in a systematic program aimed at elucidating the mechanisms of hardening in the complex commercial alloys. 1) EXPERIMENTAL PROCEDURE Single crystals of off-stoichiometric NiA1 were grown from the melt under vacuum by a modified Bridgman method. The melt was poured into a preheated alumina mold and crystal growth was promoted from one end by gradient cooling. The crystals were homogenized by annealing in hydrogen at 2400° F for 72 hr followed by furnace cooling. Chemical analysis of samples taken from several crystals gave an average composition of 88.2 wt pct Ni. Spectrographic analysis gave as the principal impurities in weight percent— Si (0.02), Mg (0.01), Fe (0.02), Ti (0.002), Cu (0.008), and Co (0.03). Tensile specimens with specifications as in Fig. 1 were prepared by a series of operations involving electrical discharge machining, precision grinding, and electropolishing. Compression specimens with dimensions 1/4 by 1/4 by -3/4 in. were prepared in a similar manner, except for the initial shaping operation using a precision cut-off wheel/two-circle goniometer unit to give selected crystal orientations. Specimens were deformed in a Baldwin-Wiedemann testing machine with furnace attachment, using a strain rate of 5 x 10-4 sec-1. The strain measuring device consisted of extension arms attached to the tensile grips (or compression plattens) at one end and leading out of the furnace to an LVDT at the other. Temperature was controlled by a thermocouple placed in contact with the specimen. According to the known phase diagram for the Ni/A1 system,' when an alloy of the specified composition is cooled from the melt, primary y (nickel solid solution) dendrites grow at the expense of the liquid phase, which becomes enriched in aluminum. At the eutectic composition the remaining liquid freezes as a two-phase mixture of y + y' (Ni3Al). Upon further cooling, a solid state transformation occurs, involving the precipitation of y' in the primary dendrites, and the complete transformation of the eutectic mixture to massive y'. The as-cast structure consists, therefore, of y + y' dendrites with interdendritic regions of massive y', i.e., transformed eutectic, Fig. 2. 2) DISCUSSION OF RESULTS 2.1) Stress-Strain Curves. Fig. 3 shows tensile stress-strain curves for crystals in orientations close to [001] deformed at temperatures from 70° to 2000°F. Both the yield stress and total elongation are strongly temperature-dependent. At 70°F, easy glide is absent, and the work hardening coefficient BIT - G/300. At T > 1500°F, the negative slope of the stress-strain curves is due to pronounced necking in the crystals. The yield stress maximum at 1500° F corresponds with a minimum in the ductility, Fig. 4. The extensive duc-

Jan 1, 1968

By J. P. Hammond, C. J. McHargue

The wire textures for cold rolled and recrystallized iodide titanium and the sheet textures for this material produced by cold and hot rolling, and recrystallization at a series of temperatures were determined. &apos;The effect of the a + ß transformation on the sheet texture was noted. UNTIL recently it was believed that all hexagonal close-packed metals deformed by slip on the basal plane, (0001), and that rolling should tend to rotate this slip plane into the plane of the rolled sheet. The pole figures of cold rolled magnesium&apos; are satisfactorily explained on this basis. There is a tendency for the <1120> directions to align parallel to the rolling direction, and the principal scatter is in the rolling direction. Zinc% as a rolling texture in which the hexagonal axis is inclined 20" to 25" toward the rolling direction. Twinning is believed to account for the moving of the basal plane away from parallelism with the rolling plane. The texture of beryllium3 places the basal plane parallel to the rolling plane with the [1010] direction parallel to the rolling direction, and the scatter from this orientation is primarily in the transverse direction. Cold rolled textures reported for zirconium&apos; and titanium5 how the [1010] directions to lie parallel to the rolling direction and the (0001) plane tilted by approximately 25" to 30" to the rolling plane in the transverse direction. Rosi has recently reported that the mechanisms for deformation in titanium are distinctly different from those commonly reported for hexagonal close-packed metals. The principal slip plane is the prismatic plane, {1010), with some slip also occurring on the pyramidal planes, (1011). However, there is no evidence for basal slip. The slip direction is reported to be the close-packed digonal axis, [1120]. In addition to the twin plane commonly reported for metals of this class, {1012), Rosi found the twin planes (1122) and {1121), with the dominant twin plane being (1121). Information regarding the recrystallization and hot rolling textures of hexagonal close-packed metals is limited. Barrett and Smigelskas report that rolling beryllium at temperatures up to 800°C and recrystallization at 700°C produce textures not differing from the cold rolled sheet texture.3 McGeary and Lustman find that hot rolling at 850°C produces the same basic texture in zirconium as rolling at room temperature.&apos; These investigators also report that the texture for sheet zirconium recrystallized at 650 °C differs from the cold rolled orientation inasmuch as the [1120] direction, instead of the [1010] direction, is parallel to the rolling direction. In the case of titanium, it is not possible to deduce which direction is preferred in the recrystallized state from the pole figures presented by Clark." The purpose of this paper is to report an extensive investigation of the preferred orientations in iodide titanium. Since the deformation mechanisms for titanium are different from those commonly given for hexagonal close-packed metals, it is not surprising to find distinct differences between the textures of titanium and other metals of this class. Materials and Methods This investigation was carried out on iodide titanium obtained from the New Jersey Zinc Co. with an analysis as follows: N2, 0.002 pct; Mn, 0.004; Fe, 0.0065; A1, 0.0065; Pb, 0.0025; Cu, 0.01; Sn, 0.002; and Ti, remainder. The crystallities of titanium were broken from the as-deposited bar and melted to form 20 g buttons on a water-cooled copper block in a vacuum arc-furnace. Hardness tests conducted on the material before and after melting differed by only two or three Vickers Pyramid Numbers, indicating no or insignificant contamination. The buttons were hot forged, ground, and etched to sizes and shapes suitable for the rolling schedule, and vacuum annealed at 1300°F. Specimens for determination of the wire textures were reduced 91 pct in diameter to 0.027 in. in 24 steps using grooved rolls. In order for the orientation of the central region to be studied, portions of these wires were electrolytically reduced to a diameter of 0.005 in. using the procedure described by Sutcliffe and Reynolds.&apos; The sheet textures were determined on titanium cold rolled 97 pct to a thickness of 0.005 in. A reduction of approximately 10 pct per pass was used, and the rolling direction was changed 180" after each pass. Specimens used for determination of the recrystallized textures were annealed in evacuated quartz tubes at 1000°, 1300°, and 1500°F. The grain size of the 1000°F specimen was sufficiently small to give satisfactory X-ray patterns with the specimen stationary. However, it was necessary to scan the surface of the other recrystallized specimens. The microstructure of each annealed specimen was that of a recrystallized material. The diffraction rings all showed the break-up into spots typical of recrystallized structures.

Jan 1, 1954

By Ralph Hultgren, Prodyot Roy

Manganese vapor pressures from 1250° to 1500°K were measured by conventional Knudsen and torsion-effusion methods in twelve Fe-Mn alloys with compositions from 9 to 80 at. pct Mn. The Knudsen re-sults agveed approximately with previous measurements found in the literature which indicated the solutions were nearly ideal. However, except for the higher manganese compositions, the initial torsion readings indicated much (up to 50 pct) higher vapor presszcres than the Knudsen method. These high readings decreased steadily with time. The results are interpreted as due to depletion of surface concentration of manganese during evaporation. Thus the initial torsion readings are the most nearly correct and Knudsen methods on alloys are to be regarded with suspicion unless it can be demonstrated that diffusion rates are rapid enough to replenish surface concentrations depleted by evaporation. For the lowest manganese contents and highest temperatures, depletion causes initial torsion readings to be too low. FEW thermodynamic data are available for alloys of the high-melting transition metals due primarily to experimental difficulties at the high temperatures involved. Measurement of vapor pressure is one of the most promising techniques to be applied to this problem. From the vapor pressure of a component of an alloy phase, its activity or its partial molar Gibbs energy can be directly calculated. From measurements over a sufficient range of temperatures and compositions the partial and integral Gibbs energies, enthalpies, and entropies may be determined through Gibbs-Duhem integration. For solid phases of variable composition, which commonly are found in alloys, measured vapor pressures are low because of depletion of the surface concentration of the more volatile component as it is selectively vaporized. Diffusion from the interior tends to restore the depleted concentration. The seriousness of the effect depends on the relative rates of diffusion and vaporization. Although depletion has been recognized as a factor,&apos; direct measurements of its rate are lacking and quantitative estimates of its effect on measurements are uncertain. In the present work the vapor pressures above a series of Fe-Mn alloys have been measured by the torsion-effusion method. This method permits a measurement of the vapor pressure of manganese as soon as the sample comes to temperature and continuously throughout the run. The rate of decline of the apparent vapor pressure measures the rate of depletion and the torsion reading at zero time should be correct. At high manganese concentrations (70 and 80 at. pct Mn), the torsion reading remained nearly constant; surface depletion was negligible. There was a slow drop in measured pressure due to bulk loss of manganese from the sample. However, for lower manganese contents, especially at high temperatures, the depletion effect was considerable and the apparent vapor pressure decreased steadily with time. For these alloys the Knudsen method should give pressures which are too low. The measurement of pressure in the Knudsen method cannot be made until enough manganese has been vaporized to be weighable. The Knudsen result is therefore an integrated average between the initial and final vapor pressures. To verify this, conventional Knudsen measurements were also made with results in approximate agreement with previously published Knudsen measurements for these alloys. As expected, for the lower manganese contents the initial torsion readings of pressure were as much as 50 pct higher than the Knudsen. THE APPARATUS The apparatus, shown in Fig. 1, is capable of operating to temperatures up to 2000°K. A vacuum of 5 x 10"6 mm Hg can be maintained. Temperatures were measured to +3° by a W-Re thermocouple placed in the dummy cell, N. The torsion cell consisted of two alumina crucibles with holes in their covers. They were placed in the molybdenum holder shown suspended from the torsion wire. Rectangular torsion wires (1 by 4 mm) were found to have superior sensitivity and less residual distortion than circular (2-mm-diameter) wires. The precision of angular measurement was found to be *0.025 deg; the variation is no doubt due to temperature fluctuation and vibration. For the Knudsen experiments the alumina cell was set on the support, N. SAMPLE PREPARATION 800-g samples were prepared by melting together electrolytic iron and electrolytic manganese and pouring the melt into a water-cooled copper mold. Melting and pouring were done under a helium at-

Jan 1, 1965

By F. Weinberg

Measurements have been made of solute segregation during dendrilic growth by using radioactive solute elements and ,measuring the activity of den(12-ites cut from decanted specimens. This has been done for both lead awl tin based binary alloys contaitzing the following solute additions: Ag, T1204, was dependet on ko, the equilibrium distribution coefficient in the following way Fay k &apos;c 0.1, C/C 0.6; for k0 >0.1. 0.6 <c,/c,< I. Qualitative obse?-vations were madc of dendritic segregation, by using autoradiographic techniques, for the Sn + Ag110 and Sn + Tlo4 systems. The observation were found to he in general agreement with the measurements ofCA/Co. Autoradiographic were also obtained of scctiolccl delzr11-iie stalks. These indicated that the stalks had a substructure, dclileated by solute corzetlt?atio?zs nlolg the substructure walls. A new dendrite growth direction <JI2> is reported for tila. SOLUTE segregation in dilute binary alloys has been investigated by Pfann,&apos; Smith, Tiller, and Rut-ter,&apos; and others. They considered the case of a slowly advancing plane solid interface, and derived expressions for the distribution of solute in both solid and liquid during solidification. To determine these expressions, they assumed no diffusion in the solid and either complete mixing in the liquid:&apos; or diffusion controlled solute movements in the liquid without any convective mixing.&apos; The present investigation considers solute segregation during dendritic growth, in which case the solid-liquid interface is not plane, and the growth rates are rapid. Segregation under these growth conditions has not been treated mathematically, because of the relative complexity of the system. It has been suggested by Chalmer, on the basis of preliminary results, that an alternative to the diffusion and heat flow controlled conditions during growth is &apos;diffusionless" dendritic growth in which solid is formed with the same composition as the liquid. He suggests this type of growth may depend upon a solvent-solute relationship that permits some solid solubility without excessive increase in internal energy, as is the case for solutions of tin in lead. On the other hand, Montariol,4 and others, have shown experimentally that some segregation does occur during dendritic growth in metals using etching and radioactive tracer techniques to indicate the concentrations of the solute. The present investigation was undertaken to determine, both qualitatively and quantitatively, the extent of solute segregation associated with dendritic growth in a series of binary alloys, as a function of solute concentration. PROCEDURE The solvent materials used were Vulcan Electrolytic tin (99.997 pct purity) and Tadanac lead (99.998 pct purity). The solute materials were Zn, Sn, and Sb (better than 99.998 pct purity), Ag and Co (99.5 pct purity), and T1 (Fisher "purified" metal sticks). Activation of the solute metals was carried out in the reactor at Chalk River, Canada. Master alloys were prepared by induction heating from the radioactive solute metal and the pure solvent, under argon, in graphite crucibles. Pieces of these alloys were then added to the solvent to give the required solute concentration. Dendrites were grown in essentially the same manner as that described by Weinberg and Chalmer, , in which controlled orientation single crystals were grown dendritically in horizontal graphite boats, and the liquid decanted. The crystals were grown and decanted in an atmosphere of tank argon. Before decanting, a sample of the liquid was drawn up in a glass tube and allowed to solidify rapidly. The orientations of the single crystals were such that <loo> was parallel to the growth direction, and (100) in the horizontal plane for lead, and [1101 and (110) respectively for tin. With these orientations long dendrite stalks formed along the bottom of the boat in the dendrite direction (<100> for lead and [I101 for tin) from which secondary branches grew. Only these secondary branches, which grew freely in the liquid from the dendrite stalk to the liquid surface, were used in the measurements. Accordingly, effects due to substrates and oxides on the surface of the liquid need not be considered. In order to measure the solute concentration C, of the dendrites, individual dendrite stalks were cut from the decanted specimens, remelted, and formed

Jan 1, 1962

By C. E. Lundin, D. T. Klodt

The binary alloy systems, Y-Ti, Y-Zr, and Y-Hf, have been investigated throughout their entire composition regions. There is no compound formation in any of the systems, and each system is characterized by a single eutectic reaction. The eutectic compositions and temperatures are as follows: A eutectoid reaction pct Y and 870°C occurs in the Y-Ti system, whereas a peritectoid reaction,: pct Y and 880°C occurs in the Y-Zr system. Peri-tectic-type reactions at temperatures above the eutectic levels are postulated for the yttrium and hafnium transfovmations. The development of the technology of yttrium has been given considerable attention during the past few years, and studies of binary phase equilibria have, of course, taken a prominent position in this development. In many respects yttrium, in the third group of metals of the periodic table, is similar to the adjacent group of metals, titanium, zirconium, and hafnium, and the knowledge of the phase relationships of yttrium with these metals is basic to their technology. MATERIALS AND EXPERIMENTAL PROCEDURES Materials. The metals for this investigation were supplied by the General Electric Co., Aircraft Nuclear Propulsion Department. The yttrium was in the form of an arc-melted ingot, and the other metals were in the form of high-purity, iodide-Process crystal bar. Table I lists the purities of these materials. Alloy Preparation. Melting was done by conventional techniques in a nonconsumable electrode arc furnace in an atmosphere of purified argon. Melting conditions for each binary system were the same. Each alloy button was inverted and remelted several times to assure homogeneity. Accurate weights of the charges and resultant alloy buttons were obtained to indicate deviations from intended compositions. No chemical analyses were obtained since melting weight losses were consistently in the range of 0.1 to 0.2 pct of the total weight. 10- or 20-g buttons for each 5.0 wt pct composition increment were melted to survey the three individual alloy systems. Additional alloys differing in composition by 1.0 or 0.1 wt pct increments were also melted to study selected regions of the systems. Metallograpllic Techniques. Standard metallo-graphic techniques were followed for mounting and rough grinding. Preliminary polishing was accomplished using 6-u diamond paste as an abrasive on a Metcloth Lap. Final polishing was done on a Microcloth-covered wheel using 1-u diamond abrasive paste. Purified kerosene was used as a lubricant for both polishing stages. • sothermal- Annealing. Alloys were sectioned for as-cast structlure examinations and then homogenized in preparation for isothermal-annealing treatments. Homo{:enization was accomplished by cold pressing the alloy buttons followed by 72-hr anneals at 1100c. The alloys were encapsulated in Vycor or quartz for the homogenization treatments or for isothermal anneals. Resistance-wound or resistance-element tube furnaces were used for the annealing treatments. The homogenized alloy buttons were cold rolled until cracking occurred or until a -in. specimen thickness was obtained. Small -in. square) specimens for the isothermal anneals were then sawed from the alloys. Each specimen was wrapped in tantalum foil before being sealed in the capsule. Temperatures during the anneals were controlled The time at temperature necessary to equilibrate the structures during the anneals was determined for each alloy system by holding triplicate specimens of alloys at a constant temperature for three different periotls. The specimens were quenched and examined microscopically to determine the number and amounts of phases present in the micro-structure as a function of time. Melting Studies. Eutectic temperatures of the three alloy systems were established from the results of incipient-melting studies conducted on as-cast alloys. Specimens to be melted were suspended on a tungsten wire inside a graphite cylinder placed in a glass vacuum chamber. An optical pyrometer was used to follow the temperature of the specimen as it was inductively heated in a high vacuum. The temperatures were corrected for emissivity losses by standardizing the pyrometer with known-melting-point metals. Accuracy of the temperature measurements is estimated to be + 10°C. The melting point of the yttrium was determined to be 1550°C by this technique. The invariant-temperature levels were also checked by an anneal-quench technique. This technique consists of annealing a series of

Jan 1, 1962

By M. Garfinkle

LITERATURE data1&apos;3 have suggested that the resolved shear stress necessary to initiate slip in a particular slip system in tungsten single crystals is strongly dependent on the tensile orientation of the crystals. This orientation dependence is contrary to the critical resolved shear stress criterion. Because the Schmid factors for slip on particular {110}( I l l), {112}(Ill), or {123}(111) slip systems in a (100) oriented tungsten crystal are virtually identical to the respective Schmid factors for a (110) oriented crystal, slip should initiate on the same system in both orientations, independent of the values of the critical resolved shear stresses. Thus, it would be expected that, for a critical resolved shear stress model to hold, the proportional-limit stress for these two orientations must be similar. The expectation of similar proportional -limit stresses has not been borne out by reported experimental observations. Rose et nl.&apos; reported that the proportional-limit stress for crystals near the (110) orientation was 92,000 psi, approximately three times that of (100) oriented crystals (31,000 psi). Garlick and probst2 reported greater than a fourfold difference. Most recently, Beardmore and ~ull~ examined tungsten crystals with orientations along the edge of the standard stereographic triangle and showed a gradual increase in proportional-limit stress from 28,000 psi for the (100) orientation to 93,000 psi for the (110) orientation. Again, the difference was more than threefold. As has been emphasized by these investigators, the apparent gross variation of proportional-limit stress with orientation precludes any meaningful analysis of slip mechanics using a simple critical resolved shear stress relation. The purpose of the present communication is to report that, by use of refined strain-measuring techniques, the proportional-limit stresses for the (100) and (110) orientations are quite similar. Obviously, to determine accurately the value of the proportional-limit stress, which is by definition the stress at which nonlinear stress-strain behavior first occurs, the method of measuring strain must be capable of high accuracy. The investigators cited used as the measured elongation the crosshead displacement of the tensile machine. This method, however, introduces extraneous strain contributions from the load train. Because these extraneous contributions are considerable in the initial portions of loading (as has been well-documented in the literature) the proportional-limit stress measurement, dependent on the deviation of a line from linearity, can be significantly affected. During the course of a recent study, room-temperature strain was measured directly on several (100)-and (110)-oriented tensile specimens axially oriented within 5 deg of the desired direction. Each specimen was fitted with two foil strain gages mounted on opposite sides of the 0.08-in.-diam reduced section. The tensile specimens were loaded at a crosshead speed of 0.01 in. per min on an Instron Universal Testing Machine. Strain was monitored through an external bridge circuit in which the specimen strain gages comprised two arms. The bridge output was recorded against the applied load. A strain of 2 x 10"" could be readily detected by this method. Some specimens were subjected to conventional loading while the load for others was cycled between zero and continually increasing values until the first deviation from linearity was observed. The results of these methods were similar, and the stress at which nonlinear behavior occurred was considered the proportional-limit stress. The proportional-limit stresses measured in this study are approximately 5000 and 6500 psi for the ( 100) - and ( 110) -oriented crystals, respectively, a range of values almost a magnitude less than those reported previously. Representative curves are presented in Fig. 1. Because of the nature of the measurements made, the point of departure of a line from linearity is often debatable. While the load-strain curve for the (100) -oriented crystals made a relatively abrupt deviation from linearity, the curve for the (110) -oriented crystal was more gradual, so that the actual point of tangency may be at a lower load than reported. Thus, the difference in values for the proportional-

Jan 1, 1967

By W. A. Young

Polynomial functions of temperature were obtained for the specific heats, thermal diffusivities, and thermal conductivities of zirconium hydrides containing 4 at. pct U. Three hydrides (H/Zr atom ratios of 1.58, 1.65, and 1.70) were studied over the range a" to 900°C and a fourth (H/Zr = 1.81) was studied over the range 0° to 760°C. The specific heats were determined from enthalpy measurements which were obtained using a unique drop calorimeter specifically designed for use with materials in which high temperature phase transitions and/or high dissociation pressures occur. Thermal diffusivities were measured by the flash method using a pulsed laser. The thermal conductiuities were obtained as the product of specific heat, thermal diffusivity, and density. The specific heats agree, within 10 pct, with values derived using a theoretical model in which the hydrogen and zirconium atoms are treated as Einstein and Debye oscillators, respectively. RELIABLE values of the thermophysical properties of the fuel are required to predict the operating temperatures and temperature response of SNAP nuclear reactors. Among the most important of these properties are the thermal conductivity, specific heat, and thermal diffusivity. A considerable number of investigations1-4 have been made of these properties for the Zr-H and Zr-H-U systems.* However, little of the drides, however, this direct method cannot yield meaningful results, since the hydrogen will redistribute under the influence of the thermal gradient, thus forming a concentration gradient; hence, one has a spectrum of compositions, rather than a homogenous alloy. Although the "average" composition of the material may be identical to the initial uniform concentration, the directly measured value of conductivity will be dependent on the thickness of the specimen, due to the highly sensitive dependence of transport properties on hydrogen content. This dependence is strikingly illustrated by the work of Bickel,5 who found that the electrical conduction of zirconium hydrides ranges from primarily hole conduction to primarily electronic conduction, depending upon the hydrogen content. Fortunately, the direct measurement of thermal conductivity is unnecessary, since it can be expressed as the product of the specific heat, thermal diffusivity, and density, all of which can be directly measured with considerable accuracy. EXPERIMENTAL Specimen Preparation. The combined fuel-moderator material used in SNAP reactors is a hydrided zirconium-uranium alloy containing -10 wt pct U. The alloy used in this work was representative of that used in nuclear reactors except that normal uranium was substituted for the enriched uranium required for reactor usage. It was produced by a triple-arc-melt and double-extrusion process. All specimens were prepared from a single cylindrical extrusion which contained 10.30 pet U, 89,35 pct Zr, and 0.35 pct impurities, The specimens for each composition were hydrided simultaneously with ultrapure hydrogen (10 ppm total impurities) using standard fuel production techniques which routinely yield homogeneous, crack-free fuel with negligible increases in the impurity levels. The hydrogen content of each specimen was determined from its weight gain and the density was measured by liquid displacement, Chemical analyses yielded hydrogen concentrations which agreed with the weight gain data within ±0.02 in H/Zr atom ratio) the concentrations of all other elements agreed almost exactly with the initial values after adjustment for the added hydrogen. The specimens used for the determination of specific heat were centerless ground to 2.00 cm diam after hydriding. A thin slice was carefully removed From each end for metallographic examination. In every case, this examination revealed a uniform structure as evidenced by the appearance and distribution of the two phases present in the fuel at the hydrogen concentrations used. TWO specimens (H/Zr = 1.600 and 1.632) appeared to be entirely 6 phase with equi-axed grains; the specimen with H/Zr = 1.756 showed

Jan 1, 1970

By E. E. Underwood, L. L. Marsh

Aluminum single crystals, alloyed with 0.042 atomic pet Cu and 0.11 and 1.1 atomic pct Mg, were subjected to constant stress creep tests, tensile tests, and hot hardness measurements within a temperature range of 300° to 866OK. Calculations based on Dorn&apos;s temperature-compensated time parameter, 6, gave a value of DH, = 27,000 cal per mol for the activation energy of early creep in aluminum single crystals. Correlations have been obtained for aluminum alloy single crystals with the parameter E for solid solution strengthening, as well as with the parameter F for solid solution hardening, by using a valence of three for aluminum. Limited measurements on tensile specimens show that the slip band density tends to decrease with increasing temperature and with decreasing solute concentration. INCREASING interest is being shown in the mechanisms of plastic deformation in single crystals during tensile and creep testing. The complexity of deformational processes in polycrystalline materials has led to a search for simpler experimental conditions. Numerous creep and tensile investigations have been conducted with pure, metallic single crystals. To a lesser degree, the effects of alloying elements on the tensile properties of single crystals have been determined. However: the literature dealing with the effects of alloying additions in single crystals under creep conditions is vanishingly small. This paper represents an attempt to narrow this gap in the knowledge of the subject. Previous investigations of creep behavior at the Battelle Memorial Institute1-1 have been of great value in the analysis of the present single crystal data. It is equally desirable, however, to ascertain the extent of correspondence between the behavior of single crystal and polycrystalline materials. For this purpose, correlations, similar to those developed for polycrystalline aluminum alloys by Dorn and co-workers, have been made with the single crystal data. The results from this study have tended to confirm and extend those correlations to the case of alloyed single crystals. Materials and Procedures Three dilute binary aluminum alloys were prepared for this investigation from 99.99 + wt pct Al, 99.8 wt pct Mg, and 99.92 wt pct (electrolytic) Cu. The nominal compositions of the alloys were 0.042 atomic pct Cu, and 0.11 and 1.1 atomic pet Mg. Precautions were taken to avoid contamination of the stock during melting and casting of the alloys. After a heat treatment of 8 hr at 925°F the alloys were extruded, then machined into) threaded tensile specimens with a 3 in. reduced section and a 0.505 in. diam. Spectrographic examination showed less than 47 ppm metallic impurities in each alloy. The single crystals were grown by the strain-anneal method, with a critical strain of about 11/4 pet giving the optimum results. In general, 3 in. crystals were obtained with the Al-Cu alloy, but smaller crystals in the magnesium alloys necessitated the use of 2 in. and 1 in. gage lengths with the low and high magnesium alloy specimens, respectively. After an electrolytic polish, the orientation of that portion of the specimen containing the largest single crystal was determined from Laue back-reflection photographs. Tensile tests were conducted at a constant load rate of about 2 lb per min. Creep runs were made in a constant temperature room, under constant stress at the higher creep temperatures, and constant load at the lower temperatures. The eloneation was measured to within ±5 microin. by a specially designed capacitance extensometer. The ex-tensometer arms were attached to the 3 in. specimens at the shoulders of the test piece or, where the crystals were smaller than 3 in., by knife-edge grips.

Jan 1, 1957

By W. M. Parris, P. D. Frost, H. A. Robinson

The effects of hydrogen content and strain rate on the static tensile and notch-rupture properties of the Ti-3Mn-complex alloy heat-treated to differed strength levels were investigated. The extent of embriulement was found to be proportional to the amount of hydrogen present and the strength to which the specimens were heat-treated. The research suggests the possible necessity of specifying lower hydrogen limits than are now allowed when titanium alloys are heat-treated to higher strengths than are presently used. The research also supports a hypothesis advanced earlier for a mechanism of hydrogen embrittlement. MUCH attention has been focused on the effects of hydrogen in in Most of the published in- formation has dealt with the effects of hydrogen on alloys in the annealed or lowest-strength condition. The work of Kotfila and Erbin3 is one of the few exceptions. In view of the fact that heat-treatments are now being used to produce high strength in titanium alloys,&apos; it is necessary that more attention be given to the effects of hydrogen on these alloys in the heat-treated condition. Research was initiated to establish the effects of hydrogen on the properties of the Ti-3Mn-complex alloy at various strength levels. This research, which supplemented that of Kotfila and Erbin, was started because it was found that high-strength tensile specimens of this alloy were strain-rate sensitive. The essential results of the research are summarized in this paper. MATERIALS AND EXPERIMENTAL PROCEDURES Material for this investigation was a 41/2-in.-diam bar forged from a single commercial heat of the Ti-3Mn-complex alloy having the composition given in Table I. The as-received forging was reduced further by forging at 1750°F to 3/4-in. square bars. About one fourth of this material was vacuum annealed at 1400°F for 24 hr to obtain a base hydrogen content of 25 ppm. The remaining bars were hydrogenated to levels of 90, 140, and 260 ppm in a large Sievert&apos;s apparatus in the following manner: Four 3/4-in. square bars, 5 in. long, were placed in the reaction chambzr. The chamber was evacuated, heated to 1400°F, and a measured amount of hydrogen was introduced. When absorbtion was complete, as indicated by the drop in pressure, the reaction tube was cooled and the bars removed. Each batch of bars was then sealed in individual evacuated Vycor containers and heated for 24 hr at 1400°F in order to distribute the hydrogen homogeneously. After vacuum-annealing or hydroge nation, the bars were rolled at a temperature (1400°F) below the ß-transus to 1/2 - in. - diam rounds. Groups of the rolled specimens representing each of the hydrogen levels were given the following heat-treatments: 1) One hr at 1300°F, water-quenched. 2) One hr at 1300°F, water-quenched, and aged 8 hr at 1100°F. 3) One hr at 1300°F, water-quenched, and aged 4 hr at 1000°F. 4) One hr at 1300°F, water-quenched, and aged 48hr at 800°F. Heat-treated bars were machined into standard 0.250-in.-diam tensile specimens having 1-in. gage lengths. Throughout the processing and testing of this material, hydrogen analyses were made by vacuum-fusion methods to check for accuracy of hydrogen additions, homogeneity, and possible losses during processing. A summary of these analyses is given in Table II It may be seen that the actual hydrogen contents were reasonably close to the desired levels. In addition, it was noted that the variation in hydrogen content within any one bar did not exceed

Jan 1, 1959

By Joseph Lindmayer, Karl M. Busen

If silicon is in contact with silicon oxide, a heterojunction is formed which induces an inversion layer ("channel"). Influences of impurities and structural parameters on the channel are discussed. There seems to be no relation between surface damage in silicon and the channel. Phosphorz~s doping of the silicon oxide has no pronounced effect on the channel. Channels which were well above the range predicted by the heterojunction model were related to the action of H* at the silicon/silicon oxide interface. Channels which were well below tlze range predicted by the heterojunc-tion model were related to a transition region in the oxide adjacent to the interface. In support of the assumed transition region and the H+ are the ex-periments described on the paper. Furthermore, the concept of metastable OH groups in silzca, known from other publications, has been used to explain certain channel characteristics by the formation and the accommodation of hydrogen in the silicon oxide. THE electrical characteristics of a semiconductor device in many cases are influenced by the conditions of its surface. Because these conditions often are changing with temperature, time, ambient, or other parameters, numerous attempts have been undertaken to stabilize them by suitable processes. Several years ago Atallal studied the silicon/silicon dioxide interface and since then increasing attention has been given to the silicon dioxide as a means to stabilize silicon surfaces. This led to the evolution of the planar silicon devices where oxide layers are used to protect places at which the junctions are intersecting the surface. The formation of the oxide layers on silicon can be carried out by a variety of processes: high-temperature thermal oxidation (exposing the silicon surface to oxidizing agents such as 02, HzO, COz), evaporation of SiOz, or anodic oxidation of silicon. Originally the oxides were considered able to "passivate" the silicon surface and it was understood that they 1) protected the surface against any influence from the ambient and 2) stabilized surface conditions which were necessary for proper device performance. It soon was realized that the second quality was not always obtainable: Atalla and Tannenbaum showed that, in the process of forming a layer on doped silicon by thermal oxida- tion, electrically active impurities in the silicon near the interface are redistributed, thus giving rise eventually to the formation of unwanted charge distributions. The degradation of planar junctions during reoxidation of silicon was observed by Barson et a. Surface studies with silicon planar junction structures indicated that the breakdown voltage depended on the kind of procedure which was applied during or after oxidation.*" Yamin and worthinge report on charge storage and dielectric properties of SiOz films at elevated temperatures. Another influential parameter on the silicon surface is discussed by Lindmayer and usen,&apos; namely the appearance of a surface potential on silicon as a consequence of the heterojunction formed by the silicon/silicon oxide interface. In the present paper the influence of impurities and structural parameters in silicon oxide in connection with the heterojunction is a particular object of our investigations. I) EXPERIMENTAL The material used was 10 ohm-cm p-type silicon slices with either damaged surfaces (mechanically lapped or polished) or damage-free surfaces (chemically polished). The majority of the slices were oxidized for 1 hr and 20 min at 1250°C in a steam + oxygen atmosphere generated by passing O2 through HzO at 90°C (wet oxygen). This led to oxide layers of about 9000 A. On some slices oxide layers were grown in pure oxygen (dry oxygen). By a photoresist process a set of 20 by 200 mil windows was then etched out from the oxide layer. The pattern of the windows is shown in Fig. 1. In a subsequent process n-type pockets with surface concentrations between 2 x 10" and 5 x 10" cm"3 were formed by phosphorus diffusion. This allowed ohmic contacts between the silicon surface and tungsten probes which for electrical measurements were placed into two adjoining windows and

Jan 1, 1965

By E. T. Hayes, A. H. Roberson, M. H. Davies

ZIRCONIUM has been produced on a pilot-plant scale for only a few years, but the potential uses have led a large number of research establishments to engage in a thorough study of the metal and its alloys. The work described in this paper is part of a cooperative project between the Bureau of Mines and the Air Materiel Command. The Zr-Cr system was one of the first investigated because of the possibilities of improving the properties at elevated temperatures, the chemical corrosion resistance, and the mechanical properties of zirconium in a manner similar to the enhancement of the properties of titanium by additions of chromium. There is no published work on the Zr-Cr system but from the similarity of the metals involved it was expected that it would be similar to the Zr-Fe&apos; and Ti-Cr&apos; systems. The materials used in this investigation were prepared in the Bureau of Mines laboratory at Albany, Ore. Zirconium was produced by magnesium reduction of zirconium tetrachloride, and a typical analysis is as follows: Fe, 0.06 pct; Ox, 0.08; N?, 0.01; C, 0.02; and other impurities such as Al, Pb, Ni, Ti, and Si less than 0.01 pct each. High purity chromium was prepared by treating crushed electrolytic chromium in a stream of dried and purified hydrogen." The resulting powder contained about 0.01 pct 0 and about 0.1 pct total metallic impurities. All alloys were prepared by arc-melting 50 g briquetted compacts of the desired composition in a Kroll-type" arc furnace using an inert atmosphere. The furnace was evacuated twice and backfilled with helium, which was gettered by melting a center zirconium button immediately before the alloys were melted. Alloys were remelted at least once to insure greater uniformity of composition and subsequently were annealed in vacuum at 1250°C for 48 hr. Fairly homogeneous alloys were obtained by this means; a slight loss of chromium from the surface by evaporation during the high temperature homogenization was noted. All alloys were analyzed for chromium and gave results in good agreement with the nominal composition. Spot checks on tungsten and nitrogen showed pick-up of these elements to be negligible. Over 70 alloys were prepared for use in this investigation; only the critical ones are shown in Table I. Alloys containing up to 10 pct Cr were amenable to hot working at 850°C and a number of these were sheath rolled to 1/16 in. thickness. Specimens were cut from the sheet for use as metallographic samples. For the thermal analysis a differential couple was used in conjunction with an X-Y recorder, the temperature of the specimen and the difference in ternperature between it and the standard nickel body were recorded simultaneously. Heating and cooling rates of 5°C per min were used. The sensitivity of the instrument was such that a difference in temperature between the specimen and standard equivalent to 0.1 mv produced a deflection of 1 in. on the recording chart. The chromel-alumel thermocouples were checked against a Bureau of Standards calibrated thermocouple. Melting-point determinations were made in a high vacuum induction furnace using an optical pyrometer. The pyrometer, calibrated against nickel, copper, and zirconium (iodide process) under near black body conditions, was focused on the base of a hole drilled in cylindrical samples. A North American Philips Geiger counter X-ray spectrometer was used for all diffraction studies. This instrument, in addition to supplying precise intensity measurements of planar reflections, has an added advantage in that metallographic specimens mounted in bakelite can be used directly, and this

Jan 1, 1953