Search Documents

By H. D. Hodges, J. K. Godbey

In order to better understand the fracturing process, bottom-hole pressures were measured during a number of typical fracturing operations. A recently developed system was used that allows simultaneous surface recording of both the bottom-hole and wellhead pressures on the same chart. The results from six fracruring treatments are summarized on the basis of the pressure data obtained. Al-though no complete analysis is attempted, the value of accurate pressure measurements is emphasized. Important characteristics of the bottom-hole pressure record do not appear at the wellhead because of the damping effect of the fluid-filled column. In four of the six treatments described, the formations apparently fractured during the initial surge of pressure with only crude oil in the well. The properties of the fluids used during the treatments are given and the fluid friction losses are obtained directly from the pressure records. This technique is also shown to be adequate for determining when various fluids, used during the process, enter the formation. INTRODUCTION Hydraulic fracturing for the purpose of increasing well productivity is now accepted in many areas as a regular completion and workover practice. Numerous articles have appeared in the literature discussing the various techniques and theories of hydraulic fracturing'. In general, three basic types of formation fractures are recognized today. These are the horizontal fracture, the vertical fracture, and fractures along natural planes of weakness in the formation'. Any one or all three of these fracture types may be present in a fracturing operation. However, with only the wellhead pressure record as a guide, it is difficult at best to determine if the formation actually fractured, and is almost impossible to determine the type of fracture induced. These difficulties arise in part because the wellhead pressure record, especially when fracturing through tubing, does not accurately reflect the pressure variations occurring at the formation. Several factors contribute to this effect and preclude the possibility of using the wellhead pressure as a basis for accurately calculating the bottom-hole pressure. These factors are: 1. The compressibilities of the fluids which damp the pressure variations. 2. The changes in the densities of the fluids or apparent densities of the sand-laden fluids. 3. The flowing friction of the various fluids and mixtures, which is dependent on the flow rates and the condition of the tubing, casing, or wellbore. 4. The non-Newtonian characteristics of a sand-oil mixture and its dependence upon the fluid properties, the concentration of sand, and the mesh size used. 5. The unknown and variable temperatures throughout the fluid column. Because of these reasons it was determined that in order to obtain a more accurate knowledge of the nature of fracturing, the bottom-hole pressure must be measured along with the pressure at the surface during a fracturing treatment. Even with accurate pressure data, a reliable estimate of the nature of fracturing is still dependent upon knowledge of the tectonic conditions. However, the hydraulic pressure on the formation is basic to any approach to a complete analysis. In order to accomplish this objective a system was developed to record the wellhead and bottom-hole pressures simultaneously at the surface. By recording both pressures on a dual pen strip-chart recorder, it was possible to greatly expand the time scale so that rapid pressure variations would be faithfully recorded. By such simultaneous recording, time discrepancies inherent in separate records are eliminated, thus overcoming one of the most difficult problems associated with bottom-hole recording systems. This paper illustrates the results obtained by using this system during six typical fracturing operations. All of these tests were taken in wells that were treated through tubing. By a direct comparison of the wellhead and bottom-hole pressures, the importance of obtaining complete pressure information during a fracturing treatment is emphasized. THE INSTRUMENTATION AND PROCEDURES The bottom-hole pressure measuring instrument consisted of a pressure-sensing element, a telemetering section, and a lead-filled weight or sinker bar. The pressure-sensing element used was an isoelastic Amerada pressure-gauge element. By using an isoelastic element, no temperature compensation was necessary in the tests described, since the temperature was believed to be well below the maximum temperature limit of 270°F. The rotary output shaft of this helical Bourdon tube element was coupled to a precision miniature potentiometer. The rotation of the pressure-gauge shaft thus changed the resistance presented by the potentiometer

ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has five major awards to make annually for excellence in technical papers, as follows: The Robert W. Hunt Medal, The Hadfield Prize, The J. E. Johnson Jr., Award, The Lewisohn Platinum Prize to senior members, and the President's Prize to junior members. ROBERT W. HUNT MEDAL The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes; first of a gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to. a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel. The scope of the term "iron and steel" shall be determined by the sub-committee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3. A sub-committee of three to five including the Chairman of the Iron and Steel Committee, shall be appointed by the iron and Steel Committee annually to adjudge the award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October Meeting, and the. award be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute. 5. The recipient of the award shall be designated "The Hunt Medallist." SIR ROBERT HADFIELD PRIZE Sir Robert Hadfield has offered an Institute prize of $1000 for researches with regard to the different forms of combination of carbon in iron and steel. Until within a few weeks no paper has been submitted which could compete for this prize. If the paper in hand should not meet the requirements, the donor has suggested that the prize be transferred and offered for: (a) the determination of the hardness in metals in connection. with super-hardness, (b) in consideration of questions of fuel economy, (c) in consideration of questions of industrial development and labor. J. E. JOHNSON, JR. AWARD This award is made from the income of a fund of $3000 donated by Mrs. Margaret Hilles Johnson in memory of her husband, J. E. Johnson, Jr., who was a prominent engineer, author of two valuable volumes on iron blast-furnace construction and practise, vice-chairman of the Institute's Iron and Steel Committee, and a frequent contributor of papers to the Institute's TRANSACTIONS.

Jan 1, 1925

By R. B. Porter, R. P. Porter, R. A. Lothrop

Changes became necessary in dredging methods employed in Idaho through passage of the Dredge Mining Protective Act (1954). Among other provisions, the law requires dredge operators to construct settling ponds of sufficient capacity and character to reasonably clarify the water used in the mining process before such water is discharged into the stream. Porter Bros. Corp., a placer mining company with many years operating experience in Oregon and Montana, became interested in strategic mineral placers in Idaho in 1950 when it was learned that prospectors had discovered a radioactive mineral deposit in Bear Valley Creek, 95 miles northeast of Boise. The company acquired mining leases and proceeded with exploration and development work on the property. After extensive research had resulted in the determination of successful separation processes, contracts were negotiated with the federal government and deliveries of columbium-tantalum and uranium concentrates commenced in 1956. The mining operations are located in a primitive area of Idaho among salmon spawning grounds and crystal-clear mountain trout streams. To avoid involvement in a very controversial issue, it appeared advisable for the company to develop water treatment procedures exceeding those requirements stated in the Idaho Dredge Mining Protective Act. Operation: The company operates one 6 cu ft continuous bucketline dredge and one 4 1/4 cu ft continuous bucketline dredge on the property. The dredges are jig-equipped, with feed being screened to 3 in. by trommels. The screening and gravity concentration methods satisfactorily separate the heavy minerals from companion clays, sand, and gravel. However, this separation of the heavy minerals requires water from the dredge pond with a minimum content of silt and colloids; therefore, water for dilution is added continuously to the dredge pond to suppress solids buildup. Discharge of this highly turbid water to maintain the proper pond level would ultimately result in an excessive silt load in Bear Valley Creek. To prohibit the turbid pond water from flowing directly into Bear Valley Creek, it was necessary to isolate the dredging area. Main by-pass canals were constructed along each side of the dredge pond and numerous secondary canals were dug for diverting seepage and snow runoff. One by-pass canal, extending more than two miles along the west side of the valley, diverts the main stream as well as tributaries entering from the west; a canal east of the dredge area diverts streams entering from that direction. At the beginning of operations in 1956, the dredge pond effluent was filtered through tailings and settled by use of coagulents in a series of lagoons. The filtrate was then discharged directly into the stream. Although this procedure gave satisfactory results in conformance with the state law, ice buildup and lagoon freezing hindered the efficiency of the process during periods of low temperature. For this reason, testing began in 1956 on a water treatment process that would operate efficiently under the extreme weather conditions encountered in Bear Valley. Development of Water Treatment System: Porter Bros. Corp. established the following requirements for effective continuous treatment of dredge pond effluent to the stream which, at low flow conditions, effluent to the stream which, at low flow conditions, would not result in a turbidity exceeding 25 ppm in the stream, 2) produce a sludge sufficiently dense to minimize disposal area requirements, 3) be semi-portable to follow dredge movements, 4) be capable of operating at low temperatures, and 5) be capable of handling a variety of capacities and turbidities.

Jan 1, 1961

By C. Chu

An investigation has been made of the radial heat-wave process using a mathematical model in two-dimensional cylindrical coordinates. This model considers combustion, convection and conduction inside the reservoir, but only conduction in the bounding formations. From a study of the general features of the process, an important phenomenon has been revealed, namely, the feedback of heat into the reservoir on the trailing edge of the heat wave. The effects of various process variables on the performance characteristics of the process have also been investigated. It was found that up to the time when the combustion front reaches a given point, the per cent heat loss, provided it is not higher than 40 per cent, is approximately directly proportional to the square root of thermal conductivity arid fuel content, but inversely proportional to the square root of gas-injection rate and oxygen concentration. The effecr of reservoir thickness is more pronounced, since halving the thickness doubles the per cent heat loss. The most decisive factor in determining the center-plane peak temperature is the fuel content of the reservoir. Within the temperature range investigated, doubling the fuel content doubles the peak temperature in the early stage, but the rate of decline of the peak temperature is high. Reservoir thickness is also a very influential factor. The peak temperature is lowered when the thickness is reduced; however, the effect of thickness becomes less pronounced when the thickness is high. Reduction of oxygen concentration increases the peak temperature in the early stage but lowers it afterwards because of the higher rate of decline of the peak temperature. Increase in gas injection rate or decredse in thermal conductivity geives a higher peak temperature which stays high for a longer period. The propagation range of the heat wave is chiefly governed by the fuel content of the reservoir. An increase of 0.2 1b/cu ft in the fuel content increases the propagation range by 100 per cent. The propagation range is more than doubled by doubling the gas injection rate, or reservoir thickness, or by reducing the thermal conductivity by 50 per cent. Comparatively, oxygen concentration has less effect on the propagation range. INTRODUCTION Several investigators have conducted theoretical studies of a radial heat wave. Vogel and Krueger1 studied a system with a moving cylindrical heat source of constant temper- ature, considering conduction in the radial direction only. Ramey2 included conduction in the vertical direction in his studies. Bailey and Larkin2 attacked a more general problem where initial well heating, vertical heat losses and arbitrary frontal velocities were included. In all these studies, however, conduction was considered to be the only means of heat transfer. Bailey and Larkin in a later paper included the effects of convection in a study involving both linear and radial geometries. Vertical heat losses were neglected in the radial case. Katz5 studied a similar problem in a one-dimensional radial model, using a heat-loss coefficient to account for vertical heat losses. Selig and Couch6 mployed a cylindrical model and investigated two limiting cases. In one case they considered no heat loss from the reservoir whereas in the other they assumed a constant temperature at the interface between the reservoir and its bounding formations. Thomas' studied a more general case but assumed a permeable bounding formation so that the convection effect is not confined to the reservoir. In the present work a more realistic and more generalized model is used. It involves a two-dimensional cylindrical system with combustion, convection and conduction inside the reservoir, but only conduction in the bounding formations. The purpose is to establish the temperature distribution both inside and outside the reservoir, to study the general features of the radial heat wave process, and to investigate the effects of various process variables on the performance characteristics of the process. THEORY We fist consider a circular porous reservoir of thickness H extending vertically from y = — H/2 to y = + H/2. The reservoir extends from a well bore radius r, to an external radius re. A stream of oxygen-containing gas is introduced into the reservoir through the wellbore. The oxygen-containing gas reacts with the fuel contained in the reservoir and forms a combustion front wherever the prevailing temperature can support the combustion. It is here assumed that this combustion front constitutes a cylindrical surface source of heat having an infinitesimal thickness in the radial direction and extending vertically throughout the whole thickness H. This is designated as Region I. We next consider a Region II corresponding to the upper and lower formations bounding the reservoir, extending from y = — - to y = — H/2 and from y = + H/2 to y = + m. Since r, is very small, we may assume that the two bounding formations have the same dimensions, symmetric with respect to the center plane of the reservoir. In this way, we may take the upper half of the system alone into consideration. In contrast with

By J. H. Jackson, J. G. Kura, M. C. Udy, L. W. Eastwood

The melting and casting of any commercial metal depends upon the success with which the problems attendant to the handling of the specific metal are overcome. Common difficulties encountered in the handling of commercial metals are tendencies to burn or oxidize excessively, low fluidity, entrapment of dross, hot cracking, cold embrittlement, cold shuts, and un-soundness caused by gas evolution. Beryllium is not only subject to these same difficulties but is generally more sensitive to them than are the more common metals, thus necessitating more exact founding precautions. Characteristics of Beryllium Certain characteristics of beryllium which make it particularly difficult to handle in the plant or laboratory are as follows: 1. The melting point of beryllium is about 2400°F and pouring temperatures vary from 2600 to 2900°F, depending upon the degree of fluidity required. The extreme chemical activity, combined with the high temperatures, makes necessary the use of inert atmospheres, slags, or vacuum for protection during melting and pouring. Furthermore, beryllium tends to react with the melting crucibles, tools, and molds, thus requiring the selection of suitable materials and proper maintenance of these items. 2. The very marked absorption of gas by molten beryllium and the subsequent evolution of gas during solidification causes a great deal of difficulty with unsoundness. Beryllium castings may also be subject to unsoundness as a result of gas formation by chemical reaction with the mold surface during solidification. 3. The very marked chemical affinity between molten beryllium and the normal atmosphere causes the formation of dross. On relatively quiescent melts, this dross forms a very tenacious film which, if carried over to the mold, can cause defects such as the formation of skins or dross in the interior or on the surface of the casting; folds or defects similar to cold shuts may also be found. 4. During the pour and attendant turbulence, the dross may be mixed into the metal and then carried to the casting. There it may be entrapped during freezing and cause internal defects, or it may float to the surface and cause severe dross defects on the cope side of the castings. 5. Solid beryllium is very weak at a temperature near the solidus line; brittleness is also a problem at lower temperatures. Thus, hot and cold cracking must be guarded against. Scope of the Experimental Work All of these problems have been given consideration in the work at Battelle. Before the work was started at Battelle, it was customary to melt beryllium in a vacuum furnace or under flux in graphite-lined induction furnaces. Because of the difficulty of preventing gas unsoundness in beryllium castings, an investigation was undertaken primarily to study this particular problem and, secondarily, to devise methods of overcoming the other difficulties encountered in the founding of beryllium. The objectives of the laboratory work were multifold: 1. To devise a practical method of melting, other than vacuum melting, by means of which consistently sound beryllium castings could be produced. 2. To obtain fundamental data which would promote a better understanding of the causes of gas unsoundness in beryllium. 3. To develop a casting technique which would permit low melt temperatures, minimize dross defects and hot cracking, and eliminate reaction with the mold surface. Up to the present time, a considerable amount of progress has been made on the first and third objectives, with the result that it can now be safely stated that consistently sound castings can be made by the open-pot melting method, using argon as a protective atmosphere and a proper casting technique. There has been some progress on the second objective of the project, but it cannot yet be safely stated that the problem is completely understood. Most of the experimental work has been conducted in an enclosed melting and pouring apparatus in which very-close control of melting variables has been effected. Findings based on the results of the work conducted in this small experimental apparatus have been applied to large-scale melts which have been made by techniques suitable for duplication on a commercial scale.

Jan 1, 1950

By J. T. Norton, J. G. McMullin

The ternary system of gold-silver-copper is characterized by a solid solubility gap and a two phase region in which copper-poor and silver-poor phases coexist. At about 30 pct gold, the two phases become mutually soluble at temperatures below the melting temperature. As the gold content is increased, the solubility temperature of the alloys decreases until at about 80 pct gold, the two phases are soluble down to the lowest temperature at which the alloys will recrystallize. Although the general form of the two phase region is known, its boundaries do not seem to have been investigated extensively. In an X ray diffraction study, Masing and Kloiberl have outlined the boundaries of this two phase field at 400 and 750°C. Using only microscopic techniques, Pickus and Pickus2 determined a vertical section of the ternary diagram showing the 14 kt alloys (58.3 pct gold). These two reports are riot in complete agreement. It has been shown3 that some of the ternary alloys are susceptible to age hardening and that the hardening is caused by the separation of a homogeneous alloy into two phases at the aging temperature. While the gold-copper binary system is an outstanding example of super lattice formation, Hultgren4 has shown that a few per cent of silver added to gold-copper destroys the tendency for ordering. Because of the age hardening possibilities of these alloys, it seemed advisable to investigate the boundaries of the two phase field more in detail using an X ray diffraction method, so as to permit a better understanding of the aging phenomena and enable predictions as to the behavior of other alloys to be made. This is especially true for the 18 kt alloys (75.0 pct Au) at the lower temperatures since they are known to exhibit age hardening. Twelve ternary alloys were prepared having the compositions shown in Table 1 and graphically in Fig 1. The gold used was fine gold bars supplied by Handy and Harmon. The silver was a bar of high purity silver from the U. S. Bureau of Standards. The copper was a bar of vacuum-treated, high conductivity copper from the National Research Corporation. The pure metals in the form of powder were weighed out in proper proportions and melted in graphite in a high frequency induction vacuum furnace. They were heated to 1100°C and slowly cooled. The ingots were then removed from the crucible, inverted, returned to the crucible and remelted. This remelting procedure was intended to reduce segregation in the ingots. After remelting, the ingots were checked for weight loss. The weight loss in each ten gram ingot was held to less than 25 mg. The remelted ingots were cold rolled and then given a homogenizing heat treatment of 16 hr at 760°C to remove any remaining segregation. Powder specimens were prepared by cutting the ingots with a fine file, one half the required amount of powder being taken from each end of the ingots. When the X ray diffraction pattern showed any difference in lattice constant between the ends of the ingot, the ingot was remelted and given an additional homogenization treatment. All powder samples were sealed in evacuated pyrex tubes for heat treatment. Ordinary pyrex proved satisfactory for temperatures up to 650°C but above that temperature it was necessary to use a special high temperature pyrex glass. Annealing at temperatures below 500°C was done in a salt bath whereas for temperatures of 500°C and above an electric muffle furnace was used. In both furnaces the temperature control was ± 5°C. In all annealing treatments samples of cold worked powder were placed in a furnace which was already at temperature. In this manner the specimens recrystallized directly to the equilibrium structure for that temperature. Time at temperature was selected so as to allow complete recrystallization, but very little grain growth. Specimens were quenched from the annealing temperatures by breaking the pyrex tubes in cold water. X ray diffraction photograms were made of all the heat treated powders using copper radiation and a Phragmen

Jan 1, 1950

By Roshan B. Bhappu, Ronald J. Roman, Dexter H. Reynolds

The reaction between manganese dioxide and molybdenite in a water- sulfuric acid medium was studied at atmospheric pressure and from 25° to 103°C. Both solids are dissolved to give, as final products in solution, Mo(VI), S(VI), and Mn(II). Stoichiornetric relationshifis are most simply represented by the equation MoSz + YMnO2 + 15H+ - HMoO-4 + 2HSO-4 + 9Mn++ + 6H20 The rate of this reaction was found to be dependent on temperature, manganese sulfate concentration, acid concentration, and, in a complex way, the surface areas of both manganese dioxide and molybdenite. Both the total amount of manganese dioxide and tnolybdenite and the ratio of manganese dioxide to molybdenite played a part in determining the over-all rate of the reaction. The effect of acid concentration on the rate was also dependent on the ratio of manganese dioxide to molybdenite. SEVERAL reports in the literature describe reactions using manganese dioxide in water-sulfuric acid media as an oxidizing agent. Nearly all previous work describes interactions between an ion and manganese dioxide, such as the oxidation of ferrous to ferric iron,' or the interaction between a molecule in solution and manganese dioxide, such as the oxidation of toluene to benzaldehyde.2 Only a few references describe the use of solid manganese dioxide to oxidize another solid in sulfuric acid. One report3 states, "Manganese dioxide in dilute sulfuric acid solutions had no beneficial effect (in leaching copper from chalcopyrite), but in more concentrated acid solutions the rate of solution was about the same as that for permanganate." In 1902 a German patent4 described a process which used manganese dioxide in strong (50°Be') sulfuric acid for oxidizing chromite ores to soluble iron and chromium salts. The process consisted of mixing the sulfuric acid with the finely ground ore and manganese dioxide. The pulp was then heated to about 120°C and an electric current passed through it. The manganese dioxide apparently dissolved in the strong, hot acid solution, oxidized the iron and chromium and itself was reduced to manganese 11! then was oxidized at the anode back to manganese dioxide, and the cycle repeated. An extensive study5 of the kinetics of the oxidation of pyrite with manganese dioxide indicated that in dilute sulfuric acid solutions (about 0.1 N) and at elevated pressures the dissolution of the pyrite was brought about by air oxidation of the iron to ferrous sulfate, followed by manganese dioxide oxidation of the ferrous sulfate to ferric sulfate. The mechanism proposed by the authors involved the oxidation of the iron at the surface of the manganese dioxide. Also! the oxidation of sulfide sulfur to sulfate was credited to the oxygen in the air, not to the manganese dioxide. Since the metallurgical literature is lacking in information concerning the use of one solid to oxidize another solid. the current investigation was under-

Jan 1, 1965

By Paul L. Burkhart

THOUGH at an earlier period brief studies had been made by the Lehigh Navigation Coal Company Inc., it was not until 1924 that J. B. Warriner, then general manager, called for a comprehensive study of timber treatment, treating solutions, and related operations. Because of the impossibility of procuring accurate costs and other pertinent treating data, the American Wood Preserving Co. agreed to treat a car of mine timber at the Port Reading plant of the Reading Railroad. Fig. I shows the treating data collected at the treating plant on this timber, which was installed in two of the Lehigh mines in 1925. Table i.—Results of Timber Survey in 1925 before Treated Timber Was Introduced Length of tunnels and gangways ft..... 522,987a Length of tunnels and gangways timbered, ft.................................. 224.880 Number of steel mine sets in use......... 2,412 Number of timber sets in use............ 63,834 Number of timber sets with evidence of rot 50: 419 Number of timber sets with evidence of squeeze..... ...................... I3,415 Percentage of all timber sets showing evidence of failure: BY wet rot........................ 6.0 By dry rot........................ 73.0 By squeeze....................... : Average life of wood set in Panther Valley, years............................... 5.3 • 99.05 miles. In the latter part of 1925, a survey of the tunnels and gangways of the company's Panther Valley mines was made to determine the proportion of gangways or tunnels timbered, cause of timber failures, approximate life of the average wood set and the approximate percentage of treated timber that it would be profitable for the company to use. Results of this survey appear in Table I. Because of the high percentage of timber that gave evidence of failure by rot, as noted in Table I, and a further study of the life of the sections where timbering was necessary, it was deemed advisable to fill 25 per cent of the yearly gangway timber requirement with treated timber. Quantities and Treatments OF Treated Timber Purchased In the early days of the program, none of the large treating companies would accept orders for small quantities of treated timber and the company was compelled to state the quantity of timber it would require at each operation in each month of the year. Table 2 is an example of the tabulation given to the various treating companies to assist them in making a yearly bid on the minimum quantity of timber required by the company during the year 1931. A bill of timber was calculated for each car, the weight of which would be between the minimum and maximum weight permitted for railroad-car loading. The treating company was paid for timber upon delivery at the operation specified. As extra cars of timber were required, they were ordered from the treating company, and payment was required On their receipt, on the basis of the piece or tonnage

Jan 1, 1942

By Paul L. Burkhart

THOUGH at an earlier period brief studies had been made by the Lehigh Navigation Coal Company Inc., it was not until 1924 that J. B. Warriner, then general manager, called for a comprehensive study of timber treatment, treating solutions, and related operations. Because of the impossibility of procuring accurate costs and other pertinent treating data, the American Wood Preserving Co. agreed to treat a car of mine timber at the Port Reading plant of the Reading Railroad. Fig. I shows the treating data collected at the treating plant on this timber, which was installed in two of the Lehigh mines in 1925. Table i.—Results of Timber Survey in 1925 before Treated Timber Was Introduced Length of tunnels and gangways ft..... 522,987a Length of tunnels and gangways timbered, ft.................................. 224.880 Number of steel mine sets in use......... 2,412 Number of timber sets in use............ 63,834 Number of timber sets with evidence of rot 50: 419 Number of timber sets with evidence of squeeze..... ...................... I3,415 Percentage of all timber sets showing evidence of failure: BY wet rot........................ 6.0 By dry rot........................ 73.0 By squeeze....................... : Average life of wood set in Panther Valley, years............................... 5.3 • 99.05 miles. In the latter part of 1925, a survey of the tunnels and gangways of the company's Panther Valley mines was made to determine the proportion of gangways or tunnels timbered, cause of timber failures, approximate life of the average wood set and the approximate percentage of treated timber that it would be profitable for the company to use. Results of this survey appear in Table I. Because of the high percentage of timber that gave evidence of failure by rot, as noted in Table I, and a further study of the life of the sections where timbering was necessary, it was deemed advisable to fill 25 per cent of the yearly gangway timber requirement with treated timber. Quantities and Treatments OF Treated Timber Purchased In the early days of the program, none of the large treating companies would accept orders for small quantities of treated timber and the company was compelled to state the quantity of timber it would require at each operation in each month of the year. Table 2 is an example of the tabulation given to the various treating companies to assist them in making a yearly bid on the minimum quantity of timber required by the company during the year 1931. A bill of timber was calculated for each car, the weight of which would be between the minimum and maximum weight permitted for railroad-car loading. The treating company was paid for timber upon delivery at the operation specified. As extra cars of timber were required, they were ordered from the treating company, and payment was required On their receipt, on the basis of the piece or tonnage

Jan 1, 1942

By W. C. Ellis

Growth directions of tin, zinc, and cadmiun whisker crystals grown spontaneously fi-om the solid are summarized. In tin the edge and diagonal directions of the unit cell are jound with the exception oj- the [110] diagonal. In cadmiurn and zinc the usual dip-ections are a or a + c. The c direction has not been ohserwed. The gvouth directions from the solid are for the most part the same as those found for vapor-grozun crystals and are the ohserz:ed glide directions in plastic j-lou. Whisker crystals of these elements grown from the solid are not twinned. Specular lateral reflections are associated with planes of snall crystallographic indices. WHISKER crystals of tin, zinc, or cadmium grow spontaneously at room temperature in periods from months to years from thin electroplates and other prepared films of the respective metals.''2 It has been established that these crystals are single, but the question of twinning, such as occurs in whisker crystals of silicon,3'4 has not been resolved. Studies of morphology have been restricted to determinations of growth directions.5-' Whisker crystals are both straight and kinked. A few studies have been made on kinked whiskers including measurements of kink anglesa and determinations of growth directions,' but unfortunately not both on the same crystals. The kink angles, for the most part, for each species are grouped closely about a few unique values, but these values are not always those between observed growth directions in a single crystal. To supplement existing data, the growth directions, identification of lateral features, and presence or absence of twinning were determined with a Weissenberg goniometer by a method described elsewhereg on eight whisker crystals of tin, five of zinc, and five of cadmium. One kinked cadmium whisker was examined in detail. The specimens were needlelike, a few microns in cross section, and of the order of a millimeter in length. They were removed from electroplated substrates on laboratory specimens and commercial equipment after several years of growth as described in Table I. Since the specimens were less than 10 p in cross section they were ideally strong with no attendant risk of plastic deformation or damage in handling. Only deformation twinning has been reported for these elements. Therefore, twinning probably should not be expected in whisker crystals of these metals, particularly a twin plane containing the growth direction. A twin plane oriented in this direction was the one sought in this study. No examination was made for twinning at the boundary between kink segments except for one cadmium crystal. Well-defined reflections occur as a whisker crystal of tin, zinc, or cadmium is rotated about its growth direction when illuminated by a beam of light Although these reflections had been noted in earlier investigations, no study of them was made, probably because the earlier studies had disclosed also that

Jan 1, 1967

By John Wulff, Robert Kamm, M. A. Steinberg

IN a previous paper1 from this laboratory, the development of a lead grid method for exploring the distribution of strain and density within metal powder compacts was described, In that work thin lead foil with rectangular holes cut at regular intervals was inserted with the powder fill, the arrangement pressed and then radiographed to permit measurement of the deformation of the lead grid. Densities at each grid element obtained in this manner were plotted as a function of the die dimensions. From such plots it was, found that the densest part of a compact pressed from one side (the top) is at the top outer region and the least dense at the bottom outer region -of the specimen. The axial density maximum occurs more often nearer the bottom than at the top. As a result of such exploratory measurements, it appeared reasonable to conclude that variations in density could be attributed in the main to die wall friction. Thus compacts of large diameter appeared relatively uniform in density except where the die fill had been uneven. Finally it was found that lubrication of the finely finished die cavity contributed more to magnitude and uniformity of density within the compact than interparticle lubrication. Since publication of the above results, it was found that circular-hole grids could be more accurately made and, when deformed within the powder, more readily measured and analyzed. Much of the former work was repeated and new results which include the effect of lubrication, compact height, pressure, speed of pressing and vacuum pressing are reported in the present paper. CIRCULAR-HOLE GRIDS AND ANALYSES OF RADIOGRAPHS Commercial lead sheet 0.008 in. in thickness was used in all the work reported. The 0.0938-in. diam holes were punched in the sheet on 1/8-in, centers to an accuracy of 0.001 in. The finished grid used contained eight or more holes in a row and from I to 24 rows. The lead sheet was clamped between two pairs of brass strips bolted to a small milling machine table which was itself bolted to a bench in correct position near a vise which held the punch. Travel of the lead grid in two dimensions was controlled by two steel lead screws calibrated in 0.001-in. divisions. A stripper plate was used on the punch to avoid distortion of the lead foil. A high carbon-high chromium (chrocar) one-piece steel die was used throughout the work. The die cavity was 1,125 in. in diam and the clearance between plungers and die wall was 0.001 in, The die was also used for pressing from both ends with two long plungers. Finally, lapping of die and plungers gave a surface whose rms value on an Abbot profilometer was 5 micro-in. The die walls and plungers were, except where otherwise noted, lubricated with a stearic acid suspension in benzene. This was put on in multiple layers and allowed to dry before filling the die.

Jan 1, 1948

By M. A. Steinberg, J. Wulff, R. Kamm

In a previous paper1 from this laboratory, the development of a lead grid method for exploring the distribution of strain and density within metal powder compacts was described. In that work thin lead foil with rectangular holes cut at regular intervals was inserted with the powder fill, the arrangement pressed and then radiographed to permit measurement of the deformation of the lead grid. Densities at each grid element obtained in this manner were plotted as a function of the die dimensions. From such plots it was found that the densest part of a compact pressed from one side (the top) is at the top outer region and the least dense at the bottom outer region of the specimen. The axial density maximum occurs more often nearer the bottom than at the top. As a result of such exploratory measurements, it appeared reasonable to conclude that variations in density could be attributed in the main to die wall friction. Thus compacts of large diameter appeared relatively uniform in density except where the die fill had been uneven. Finally it was found that lubrication of the finely finished die cavity contributed more to magnitude and uniformity of density within the compact than interparticle lubrication. Since publication of the above results, it was found that circular-hole grids could be more accurately made and, when deformed within the powder, more readily measured and analyzed. Much of the former work was repeated and new results which include the effect of lubrication, compact height, pressure, speed of pressing and vacuum pressing are reported in the present paper. Circular-hole Grids and Analyses OF Radiographs Commercial lead sheet 0.008 in. in thickness was used in all the work reported. The 0.0938-in. diam holes were punched in the sheet on 1/8-in. centers to an accuracy of 0.001 in. The finished grid used contained eight or more holes in a row and from I to 24 rows. The lead sheet was clamped between two pairs of brass strips bolted to a small milling machine table which was itself bolted to a bench in correct position near a vise which held the punch. Travel of the lead grid in two dimensions was controlled by two steel lead screws calibrated in 0.001-in. divisions. A stripper plate was used on the punch to avoid distortion of the lead foil. A high carbon-high chromium (chrocar) one-piece steel die was used throughout the work. The die cavity was 1.125 in. in diam and the clearance between plungers and die wall was 0.001 in. The die was also used for pressing from both ends with two long plungers. Finally, lapping of die and plungers gave a surface whose rms value On an Abbot profilometer was 5 micro-in. The die walls and plungers were, except where otherwise noted, lubricated with a stearic acid suspension in benzene. This was put on in multiple layers and allowed to dry before filling the die.

Jan 1, 1949

By Falih Ergunalp

REGULAR production of chrome in Turkey started in 1860 with the operation of the Bursa deposits (5, Fig. I). Others were discovered at Makri, near Fethiye (3, Fig. I). For 33 years Turkey remained the principal source of this mineral. While new discoveries were coming in elsewhere, Turkey's output declined until 1921, as a result of four successive wars, which ruined the economics of the country. In 1927 a revival came with the production of 18,000 tons. In that year the Société Minière de Fethiye was formed. This company now operates mines in the Vilayets of Aydin, Denizli, Burdur and Mentese, and it has reached a maximum production of between 80,000 and 90,000 tons annually. The Turkish output therefore increased from 29,000 tons in 1930 to 55,000 tons in 1931; and to 119,009 tons in 1934. The second phase in the increase in chrome production in Turkey came about in 1935, when the Government decided to reorganize and control the mineral industry of the country according to the principles of "government control" of the present regime. Up to that time the mineral resources of the country had been exploited by private concerns. In 1935, the M.T.A. (Maden Tetkik ve Arama) Institute (Institute of Mining Research and Geological Survey) was established by the Government to do the geological and geophysical survey work and discover new mineral resources for the country. Before the establishment of the M.T.A. Institute, the chief chrome-producing region was Fethiye (3 and 4, Fig. I). As a result of the extensive work of this bureau, many new chrome deposits have been discovered and are now in production. The operational field of the mineral industry was given to Eti Bank, another Government-sponsored and Government-controlled establishment. Eti Bank gradually took over the exploitation of existing mines by purchasing them from privately operated companies. Attention was first given to the Zonguldak collieries and to the different chrome deposits scattered over the country. The Guleman mines (14, Fig. 1) were developed and put in operation in 1936. Since then the bulk of Turkish chrome output has come from this mine, which yields the highest grade ore in the world (averaging 52 per cent Cr2O3). In 1939, the recently discovered chrome deposits to the north of Eskisehir went into production, yielding ore having a Cr2O3 content of 51 to 52 per cent. Today, more than ever, the efforts of both the M.T.A. Institute and the Eti Bank are concentrated on finding new deposits and placing them in operation. There are still many promising regions of the country that merit systematic surveying and prospecting for chrome ores. Thus it is probable that Turkey will continue to make noteworthy progress in chrome output. As the annual chrome production of

Jan 1, 1944

By J. G. Patchett, R. W. Rausch

Fresh waters and the presence of clay in many Rocky Mountain and West Coast sands require special methods of log analysis. Archie's saturation equation requires addition of a shale correction term, and the SP equation must also be modified to account for clays. Suitable equations were developed several years ago, but have not been widely used due to the algebraic complexity. A computer-oriented method has now been developed to overcome this problem. The basic shaly sand equations are rearranged in four different ways to permit solution for various sets of available input data. Essential to application of the method is the correction of observed SP values to those that would be observed if the resistivity of the formation waters were exactly interchangeable with the activity. A graphic method for doing this is given. Where conditions require consideration of the effect of clay in the sands, the method presented has been found to improve the accuracy of water-saturation determinations. INTRODUCTION Log interpretation in many Rocky Mountain and West Coast basins is complicated by rapid vertical and lateral changes in water resistivity. Calculation of formation water resistivity from the SP curve becomes difficult in zones that contain clay, since changes in SP deflection may be due to changes in either clay content or water salinity. In hydrocarbon-producing reservoirs, the problem is further complicated because hydrocarbon saturation also reduces the SP.1 A log interpretation system using computers has been developed to provide a solution to this problem, based on equations proposed by de Witte.2 Four different simultaneous solutions of de Witte's equations have been made. Each solution method uses a different set of input data as independent variables. Thus, a choice of solution method is possible, depending upon the logs run and the availability of other data. Two of the solutions do not require a knowledge of water resistivity. This system is intended to be used primarily in multiple sandstone-shale sequences of low and moderate resistivities where the principal contaminant in the sandstones is clay. However, where sufficient regional data are available, interpretation in single-zone sandstone reservoirs can also be improved by using the method. THEORY AND HISTORY OF SHALY SAND ANALYSIS The log interpretation formula originally proposed by Archie3 in 1941 is applicable only to rock-fluid systems wherein the rock has negligible electrical conductivity. In 1949, Patnode and Wyllie4 showed that if the rock itself can be considered conductive due to the presence of clay, a different calculation approach is necessary. During the following years, this problem was investigated at great length, as was the related problem of the effect of rock conductivity on the SP.5-11 These investigations established functional relationships between SP, resistivity, water saturation and water resistivity for such a formation. Refs. 2 and 12 provide summaries of these studies. Unfortunately, practical use of these relationships required that water resistivity be known independently from the SP. Although log interpretation methods for rock systems containing clay were proposed at that time,' they were not generally accepted for routine use. There are three principal reasons for this. First, in many field situations involving high-salinity water, rock conductivity may be neglected (even if present) without introducing appreciable error. This may be seen by considering the following expression for waier-saturated rock.' 1/R2=1/R1+1/FRn....(1) where 1/R, is conductivity due to clay. As Rw becomes small, I/FRw becomes much greater than 1/R, which may be neglected. Where 1/R, may be neglected, the sandstone is called clean. If the term may not be neglected, the sandstone is termed dirty or shaly. For resistivity purposes, the classification between clean and shaly sands then depends not only upon the conductivity due to shale in the sand, but also upon the resistivity of the associated water (shale is used here to mean surface condition due to disseminated clay). A sand of given conductivity might safely be treated as clean in association with high-salinity water, but would require shaly sand methods if associated with fresher waters. Shaly sand methods are not required in many areas having saline waters; but in Rocky Mountain and West Coast sands having relatively fresh waters (often more than 0.3 ohm-m resistivity at formation conditions), the shaly sand methods are needed. Errors Rw calculations from the SP due to the presence of shale are likewise related to water salinity. In saline water formations drilled with fresh mud, the ratio of mud filtrate resistivity to water resistivity is high, the SP is large and the presence of shale can introduce large errors in water resistivity calculated by the conventional method. When the resistivity ratio is low, the errors are smaller. At zero SP, no error would result from shale. Thus, from the SP viewpoint, a given rock could be shaly if associated with a saline water, and clean in association with a fresh water, which is the opposite of the resistivity-oriented definition above.

By Jaakko Kajamaa

Neutron diffraction was applied to determine sheet textures by the transmission method. Cold-rolled and recrystallized copper sheets were investigated. The amount of cube texture was determined for three compositions, in which the phosphorus content was, respectively, 0, 0.005, and 0.03 wt pct. The heat treatment was in every case 8 sec at 650°C. In the two latter cases the cube texture was prevented. In addition a comparison with the X-ray diffraction transmission method was made with the 96 pct cold-rolled copper sheet. Outer parts of both (111) pole figures can be considered to be rather identical. This is seen from the fact that the intensity ratio ITD/120" was 0.45 for neutron diffraction and 0.40 for X-ray diffraction. Differences between the methods were discussed in detail. Features peculiar to neutron and X-ray diffraction in texture studies were listed and compared. In this work neutron diffraction was applied to determine sheet textures. Specifically, it was desired to ascertain whether this method can be used to reveal differences when compared to other methods. In addition, the amount of the cube texture in copper sheets was determined as a function of phosphorus content. Previous applications of neutron diffraction to texture problems include the following: nickel wires,' wire of some bcc metals,' and uranium bars.3 In the neutron diffraction technique the greatest difference is in the sample—its method of production and its volume. A sample needs no treatment and its volume is roughly 105 times larger than the volume of an X-ray diffraction sample. The cold-rolled sheet was investigated both by neutron diffraction and by X-ray diffraction, because it is expected that, due to large number of defects, possible differences in the results of the two methods would be revealed. It is a well-known fact that X-ray lines show broadening when cold-worked. Analysis has shown that this is based chiefly on small crystalline size, micro-stresses, and/or faults.4'5 Neutrons are sensitive to the above-mentioned disturbing factors as well, but circumstances in diffraction are different from the X-ray case. Because the sample represents a larger volume, the result is an average over that volume. In addition, it can be assumed that the sample has preserved its original structure, because it needs no special preparation. The particular limitation of neutrons is the relatively low neutron intensity available from nuclear reactors. This decreases the resolution as compared to the X-ray diffraction methods. Furthermore, absorption mainly reduces diffracted X-ray intensity, while multiple scattering effects, i.e., secondary extinction, disturb neutron diffraction. SO neutrons and X-rays behave in a different way when interacting with matter. As in other structural investigations, one can utilize this difference in texture studies as well. One cold-rolled and three recrystallization textures in copper sheets were investigated by neutron diffraction. The samples were produced at the Outokumpu copper factory to the specifications shown in Table I. The paper is divided into five parts. The first deals with the theory of the measurement. In the second, experimental procedures are described. Results are presented in the third part. Both cold-rolled and re-crystallized samples are studied. Discussion is in the fourth part, and finally in the fifth part some conclusions are drawn. 1) THEORETICAL CONSIDERATIONS Properties peculiar to neutron diffraction are the following: a) the scattering length varies greatly between one element and another; b) many of the elements do not absorb neutrons appreciably. In this connection it is of primary interest to know the interaction of neutrons with lattice imperfections. As with X-rays this problem leads to diffraction analysis of deformed and recrystallized metals. From the physical point of view the main difference is that neutrons are scattered by nuclei (magnetic scattering is not considered here), whereas X-rays are scattered by electrons. The features peculiar to neutron and X-ray diffraction methods in texture studies are listed in Table 11. Pole figures are an important tool in performing structural analysis of deformed or recrystallized metal. Present texture research technology requires pole figures which are as precise as possible. The choice between these two methods depends on the technical information which is required. The X-ray diffraction transmission technique may give results which are not necessarily representative of the average physical state of the sample. Although foil samples normally contain enough crystallites for diffraction, they may not necessarily represent the whole structure. An example of this problem is the frequently observed difference between the "surface" and the "inside" texture of a sample. The production of foil samples may disturb the original structure of the parent material. The selection and orientation of the foil from the sample is quite arbitrary. Normally, a highly deformed piece of metal has several texture components. Different components are deformed in a slightly different manner. This is a re-

Jan 1, 1969

By V. Pasupathi, R. E. Hummel, J. W. Koger

Specimens of P1 brass were plastically deformed at room temperature to various degrees of deformation and subsequently cooled in order to transform them to low-temperature martensite. Deformation shifts Ms. A, , and the temperature of minimum resistivity to lower temperatures, and also decreases the temperature coefficient of electrical resistivity. These properties change rapidly up to about 15 pct reduction but vary very little with higher deformation. The possible relationships between martensite formed by deformation and the M, temperature of low-temperature martensite are discussed. Evidence is given that deformation martensite delays the formation of low-temperature martensite. BETA' brass undergoes at least two different types of martensitic transformations. One of these transformations (B1- B2) was first observed by Kaminski and ~urdjumov' and occurs when 81 brass with a zinc content between 38 and 42 wt pct (quenched from the single-phase region) is cooled below room temperature. Jollev and Hull' determined the structure of 0" from X-ray and electron-diffraction data as ortho-rhombic. Kunze came to the conclusion that the super-lattice cell of 0" is one-sided face-centered triclinic (pseudomonoclinic). The second martensitic transformation (B1-A1) occurs when the specimens are deformed at or somewhat above room temperature. This type of martensite will be called deformation martensite. Horn-bogen, Segmuller, and Wassermann4 determined the structure of deformation martensite to be bct. (An intermediate phase, az, occurs before the final phase appears.) At deformations higher than 70 pct, a, transforms into a.4 A critical temperature Md exists above which no transformation occurs during deformation and is estimated to be around 400°C in P1 brass.5 This martensite has elastic properties.6 When the sample is stressed, martensitic plates appear; when the stress is released, the plates disappear. The present paper studies the effect of deformation martensite on the formation of low-temperature martensite. The experiments involved samples of 8, brass which were plastically deformed by various amounts and were subsequently cooled below the transformation temperature. EXPERIMENTAL PROCEDURE The 13 brass investigated was made from 99.999 pct pure copper and 99.9999 pct pure zinc and contained 38.8 wt pct Zn. The specimens, consisting of foils 0.1 mm in thickness, were heat-treated at 8'70°C for 15 min in an argon atmosphere and then quenched into ice water. They were then deformed by cold rolling and subsequently cooled at a rate of 1°C per min. The martensitic transformation that occurred during cooling was followed by electrical resistivity measurements. The resistance measurement technique and its accuracy have been described in a previous paper. Because the transformation 81 —-8" occurs below room temperature, the samples were placed in a cryo-stat which contained isopentane as a cooling medium. The isopentane was cooled by liquid nitrogen pumped under pressure through a 15-ft coil of copper tubing which was immersed in the isopentane. The nitrogen flow was regulated by a temperature controller using two thermistors in the cooling medium. The cryogenic liquid could be heated with an immersion heater. The useful temperature range with this device was from +25° to approximately -155~C. EXPERIMENTAL RESULTS Resistivity Measurements. The following abbreviations are used in this paper to label the characteristic temperatures during the martensitic transformation. M, is the starting point of the martensitic transformation and is defined as that temperature where the resistivity vs temperature curve on cooling first deviates from a straight line. Mf is the temperature at which the martensitic transformation is completed. On reheating, the transformation from martensite to the parent phase starts at a temperature A, and ceases at a temperature Af. Fig. 1 presents five different resistivity vs temperature curves corresponding to the transformation of brass from Dl to 8" after different degrees of reduction in thickness. The following observations can be made from these curves. 1) With increasing degree of deformation the Ms temperature is shifted to lower temperatures. This shift ranges up to 35°C compared to the undeformed state. This is also indicated in Fig. 2, where AM, (the shift of Ms, compared to the undeformed state) is plotted vs the degree of deformation. AM, increases rapidly until a reduction of about 15 pct is reached. With higher deformations, no additional increase in AM, was found. 2) With increasing degree of deformation the temperature of minimum resistivity (M) is also shifted to lower temperatures. The shift, attains a maximum of about 61°C compared to the undeformed state. In Fig. 3, AM is plotted as a function of deformation. It can be seen that, as in 1 above, AM increases rapidly and no further shift of M occurs for deformations greater than 15 pct. 3) The temperature coefficient of resistivity, is given by the slopes (dp/dT) of the linear portions of

Jan 1, 1969

By J. E. Worthington, W. H. Spence, I. T. Kiff

Gold was discovered at the Haile mine in Lancaster County, South Carolina, in 1827 or 1828, and since that time the mine has been worked intermittently by both open-pit and underground methods until its forced closure in 1942 by World War II. Production figures are incomplete, especially for the early years, but the total gold produced is estimated to have been greater than 200,000 oz. Thus, the Haile mine has been the most productive gold mine in the eastern United States. The upper, residually enriched ores were relatively rich, but the bulk of the production has come from the mining of lower grade ores. General Geology The Haile mine is located in late Precambrian or early Paleozoic rocks of the Carolina slate belt at the edge of the Atlantic Coastal Plain [(Fig. 1)]. The metamorphic grade is lower greenschist facies and the rocks have been folded into a sequence of northeast-trending isoclinal folds. The gold is associated with siliceous, pyritic, and kaolinized felsic pyroclastic and tuffaceous rocks in an interbedded volcanic and volcanoclastic sequence of felsic to mafic tuffaceous rocks and argillaceous sediments [(Fig. 2)]. The ore bodies occur in two northeast trending zones approximately 500 m apart; each zone is 30-70 m wide and 600 m or more in length, with possible extensions to the east beneath the Coastal Plain sediments. Mineralogy. Gold in the Haile mine is always associated with siliceous and/or pyritic ores. The gold occurs in at least three states: As native gold as originally deposited; as residual gold derived from the breakdown of pyrite; and as gold included in pyrite. Major associated minerals in addition to quartz and pyrite are kaolinite, sericite, and iron oxides. Minor molybdenite, arsenopyrite, pyrrhotite, copper sulfides, sphalerite, rutile, and topaz are also present. Petrology. The gold-bearing ore zones vary from highly siliceous rocks to pyritic massive sulfide lenses. This variation is most easily seen today along strike from the Haile pit to the Red Hill pit. Ore grade material still exposed in the wall of the Haile pit consists of a highly siliceous and very thinly bedded rock containing minor pyrite. Along strike, the character of the mineralization changes to pyritic massive sulfide lenses occurring interbedded with siliceous horizons at the Red Hill pit. The siliceous rocks vary from the thinly-bedded material as just described from the Haile pit to silicified fragmental-appearing rocks to totally recrystallized cherty rocks lacking any recognizable primary features. Scattered, apparently at random, throughout the very thinly-bedded and very fine-grained ore face of the Haile pit are seemingly anomalous silica-rich clasts or concretions up to 5 cm in diameter which will be discussed later in this paper. Alteration. One of the most striking features of the Haile deposit is the alteration mineral assemblage which is intimately associated with the siliceous and pyritic ores. This altered material has been intersected in drill core at depths greatly exceeding the modern weathering profile and is, therefore, of hydrothermal origin rather than from supergene processes. This "sericite," actually a fine-grained mixture of sericite, kaolinite, and quartz, can be shown to stratigraphically underlie the gold- quartz-pyrite zone, and is well exposed in the open pit just southeast of the Haile and Bumalo pits. Relict textures indicate that this highly altered material was originally a felsic ash flow. Other similar alteration zones have been found in outcrop and drill core underlying the remaining ore bodies. Thus each of the mineralized zones consists of two parts: A siliceous and/or pyritic gold-bearing ore zone which is stratigraphically underlain by a zone of high alumina minerals, in this case sericite and kaolinite along with variable amounts of quartz. A green chrome mica, presumably fuchsite, is present in trace amounts in the high alumina zone. Genesis An adequate model to explain the origin and distribution of the gold deposits in the Carolina slate belt is presently lacking. Worthington and Kiff1 suggested a volcanogenic origin for certain gold deposits in the North Carolina slate belt from the waning exhalations of felsic volcanic piles. They also pointed out that such an origin has similarities to many epithermal precious metal deposits located in more recent volcanic piles in the western United States. A further key to the understanding of the genesis of the gold mineralization at the Haile mine is the close association of the mineralization in siliceous and sulfidic horizons to the genetically related and stratigraphically underlying high alumina alteration. Such high-alumina alteration is common around felsic volcanic centers in the Carolina slate belt and the mineralogy as seen today consists of some combination of kaolinite, sericite, pyrophyllite, kyanite, andalusite or sillimanite depending on the local prevailing grade of metamorphism. Accompanying the high-alumina alteration are large quantities of pyrite and iron-oxide minerals as well as characteristic minor accessory minerals often including base metal sulfides, fluorine-bearing minerals (topaz, fluorite, apatite), titanium-bearing minerals (ilmenite, rutile),

Jan 1, 1981

By A. M. Skov, L. F. Elkins

First response to large-scale water flooding in the fractured very low permeability Spraberry sand has led to a new unique cyclic operation. Capacity water injection is used to restore reservoir pressure. This is followed by marly months production without water irzjection and the cycle repeated. Expansion of the oil, rock and water during pressure decline expels part of the fluids but capillary forces hold much of the injected water in the rock. At least with reservoir pressure restored and with partial water flood development, field performance has proved this cyclic operation is capable of producing oil from the nzatrix rock at least 50 per cent faster and with lower water percentage than is imbibition of water at stable reservoir pressure. INTRODUCTION The Spraberry Field of West Texas presents unusual problems for both primary production and water flooding. Extensive interconnected vertical fractures in the fractional-md sandstone permitted recovery of oil on 160-acre well spacing, but they made capillary end effects dominant. Primary recovery by solution gas drive is less than 10 per cent of oil in place. The concept of displacement of oil from the sand matrix by capillary irnbibition of water has led to field techniques which promise greatly increased oil recovery. Free exchange of laboratory research, reservoir information and results of field pilot tests among the various companies has been very important in development of this technology. Five units covering a total of 170,000 acres have been formed for water flooding, and 10 other areas covering an additional 175,500 acres are in various stages of unitization. Part of the Driver Unit reaching fillup first has demonstrated very unusual waterflood behavior and indicated numerous operating problems that will develop within and among the various units. SPRABERRY ROCK AND PRIMARY PERFORMANCE The Spraberry, discovered in February, 1949, is a 1,000-ft section of sandstones, shales and limestones with two main oil productive members: a 10-15 ft sand near the top and a 10-15 ft sand near the base. In part of the field some thinner intermediate sands are oil productive, and others are water bearing. All sands have permeabilities of 1 md or less and porosities of 8-15 per cent. Ordinary core analysis and electric and radiation logs are ineffective in differentiating between oil productive and nonprcductive sands. Sands capable of containing producible oil are best identified by mercury injection capillary pressure measurement and, in some cases, by core water saturation. About 3,500 wells have been drilled in the 500,000-acre trend. Vertical fractures were observed in practically all Spraberry cores. Continuity and interconnection of fractures were confirmed by pressure interference among wells during early development.' Major fractures trend northeast-southwest as indicated by oriented cores and confirmed by five fluid injection tests, by analysis of the pressure transients observed during development,''' and by three interference tests in the Driver Unit Water Flood reported herein. Fracture spac- ing probably averages inches to a few feet. Spraberry wells typically produced 100-400 BOPD initially after hydrauLic fracture treatments. By 1962 oil production had declined to an average of 12 bbl/well/day, near the economic Limits of operation. Reservoir pressure had declined from 2,300 psi initially in the Upper Spraberry and 2,500 psi in the Lower Spraberry to 500-1,000 psi. Partial closing of the fractures with declining reservoir pressure is believed to be the cause of such low oil production rates at these relatively high reservoir pressures. Cumulative recovery of 208 million bbl of oil is 80 to 90 per cent of that recoverable by primary means. Performance of the entire reservoir is summarized in Fig. 1. IMBIBITION WATER FLOODING By 1952 reservoir performance indicated low primary recoveries. Most engineers, expecting serious channeling of injected fluids through the fractures, held little hope for secondary recovery. With its extensive background of research on the fundamentals of fluid flow within reservoir rocks, Atlantic's Research and Development Division on short notice in 1952 conceived that displacement of oil by capillary imbibition of water into the rock might significantly increase Spraberry recovery. Laboratory data reported by Brownscombe and Dyes scaled to probable reservoir conditions showed potential waterflood recovery equal to or greater than primary recovery with a 10-15 year flood life.= A pilot test using three 40-acre injection wells, one central producing well and 18 surrounding observation wells demonstrated technical feasibility of the process. Injection of 1.5 million bbl of water from November 1952 to August 1955 proved water entered the rock and displaced oil

By S. M. Purdy

Under certain conditions of hot rolling and air cooling from the hot-rolling temperature, bars of a high carbon (0.40 pct C) chrome-nickel austen-itic alloy were found to show magnetism even though no ferrite or martensite could be detected by microscopic or X-yay methods. The appearance of magnetism in such alloys may come from chromium impoverishment of the austenite grains near the precipitated carbide particles. SPORADICALLY, hot-rolled bars of Silchrome 10, an exhaust valve steel, have been found to be magnetic. Because of the analysis of the alloy—0.40 pct C, 18 pct Cr, 8 pct Ni, 3 pct Si —magnetism is unexpected. Preliminary investigation showed neither martensite nor ferrite to be present; only austenite and Cr23C6. Since a literature search was fruitless, a brief study was made of the appearance of magnetism in this alloy. The only basic difference between the two heats is the nitrogen content. Permeability was measured using a Severn magnetic gauge. This instrument consists of a magnet mounted on a counterbalanced arm. A set of calibrated plugs is placed in contact with one pole of the magnet. The specimen is placed close to the other pole of the magnet. If the specimen pulls the magnet away from the plug, it has a permeability greater than that marked on the plug. This technique is swift and reproducible. Previous experience has shown that the permeabilities obtained corresponded to those obtained on a permeater with a field strength of 100 oe. Specimens from both heats were annealed at temperatures between 1700 and 2300°F. One set of specimens was water cooled and another furnace cooled. All the water-quenched specimens were non-magnetic; the furnace cooled ones were magnetic as shown in Table I with no difference being observed between the two heats. Microstructural examination of the specimens showed the expected increase in carbon solubility with increasing temperature. Carbide solution was complete at 2200°F. The specimens heated to 1900°F or below showed some carbide precipitation from the hot-rolled structure. A furnace cooled specimen from a given temperature showed less carbide out of solution than the water-quenched specimen from the next temperature below; e.g., the specimen furnace cooled from 2100°F showed less carbide out of solution than the water-quenched specimen from 2000" F. These studies indicated that the appearance of magnetism was not related to the quantity of carbon in or out of solution and it was related to precipitation at temperatures below 1700" F. A set of samples annealed and water-quenched from 2100° F was aged for 4 hr at temperatures between 1000" and 1600°F; all were non-magnetic. A second set of samples, similarly annealed, was aged 1 to 24 hr at 1200°F with the results shown in Table II. None of the latter set of specimens showed magnetism until they had been aged about 8 hr. Magnetism was quite strong after aging 24 hr. X-ray diffraction studies on several of the magnetic specimens showed that the austenite had a lattice parameter of 3.58A and that the carbide was Cr23C6. Several of these samples were electrolytically digested in 10 pct HCl in ethanol, with a current density of 0.1 amp per sq cm. None of the particles in the residue were magnetic. Accidentally, one cell was run at 1 amp per sq cm; e.g., magnetic particles were found in this residue. After careful separation, the magnetic particles were mounted on a quartz fiber and their diffraction pattern determined using a 5.73-in. Debye-Sherrer camera with CrK radiation. These particles showed a fcc structure with a lattice parameter of 3.57A. Prolonged exposure, up to 16 hr, produced no other lines on the film. The following facts seemed to be established at this time: 1) Austenite was the magnetic phase. 2) Neither ferrite nor martensite could be detected. 3) Magnetization could be produced by aging at 1200°F. One explanation of these data is that the carbide precipitation impoverishes the region immediately around the carbide particle of carbon and chromium and increases the proportion of nickel. All of these serve to increase the Curie temperature of the region around the carbide particle. If the composition change is enough, the Curie temperature will rise above room temperature. If the volume of the affected region is great enough, the magnetism will become detectable. At low aging temperatures, composition changes are great enough but the overall volume of impoverishment is quite small

Jan 1, 1962

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

0. C. Ralston and F. Fraas—Dr. Sun and associates have presented an interesting paper not all of which is comprehended by us. The data assembled measure the deflections of particles in an electrostatic field as a function of a number of independent variables and some dependent variables that are not sharply differentiated. These data are all based on a Johnson type machine of definite, well-described geometry, something not often done in electrostatic separation literature. One new fact brought out by this technique is the effect of coal dust on admixed pyrite and quartz. The effects are opposite in character, as should be expected and we do not agree with the authors that these effects are negligible. Fraas' also used a multiple cell "distribution analyzer" and gives in fig. 5 of his paper a straight line plot with no humps or curves. This is not necessarily at variance with Sun's results because Fraas used a larger gap between electrodes and had no evidence of particles adhering to or dropping off the charged electrode. The section of Sun's paper on effect of surface conductivity contains a speculation that the dielectric constant "represents more or less the electrical conductance of the bulk body instead of the surface of the mineral particles." A simple picture of the meaning of the dielectric constant is that it is the specific inductive capacity of a dielectric when used as the dielectric between the plates of a condenser. It is at once evident that the above speculation confuses capacity with conductance—two definitely independent variables. We ask the authors to state in what group or subdivision their garnet belongs; what method and units were used in calculating the data of col. A, table I and their meaning; what was the temperature of the carrier roll and, finally, has any effort been made to investigate the effects of particle shape on distribution in the electrostatic field? S. B. Hudson—I have read this article with great interest. We have been engaged in research work on the principles of electrostatic separation in this laboratory for some time now, and our findings agree with those of the authors in many respects. The article shows evidence of careful and valuable research in the field of electrostatic separation. A "distribution analyser," very similar to that described in an earlier article by one of the authors," was incorporated in an inclined plate-type electrostatic separator designed and built in the Melbourne University laboratory in 1948 for investigation purposes.22 The actual splitting edges were machined from y! in. per-spex, and the paper hoppers were supported on linen thread immediately below the perspex dividers. These dividers fitted into machined slots in a framework to give accurate Yz-in. spacings. The hoppers (staggered) fed directly into a rack of test tubes, which is supported on a vertical pantograph arrangement. The rack was positioned with guides on the horizontal pantograph stand, and this ensured positive alignment when replacing the rack after making weighings. In later work, when much heavier feed rates were used, of the order of 30 to 40 Ib per in. per hr a rack fitted with rectangular metal containers and similarly aligned was used. Some work was done here on comparing the distributions of minerals when passed separately and when passed as a mixture, and it was found that there was quite an appreciable difference in the two results.= However, in our separator the particles do not pass down the plate in a single layer, and this difference is probably caused by collisions of one mineral particles with the other mineral particles. In most of the investigational work here, the change of the center point of the distribution is measured to establish the effect of a variable, such as voltage. Two minerals (zircon and rutile) have been studied rather exhaustively, and it was found that their distributions are very nearly normal. Owing to the sharpness of the distribution curves, the usual method of obtaining the mean or median was inaccurate, and was not used; instead the mean (also the median), calculated on the assumption of a normal distribution, was used to locate the center point of each distribution and proved satisfactory. The effect of polarity becomes very apparent in the plate-type separator where frictional charges play a very important part when using highly resistive minerals such as zircon. With rutile, a comparatively conductive mineral, polarity of the electrode has little effect. On the other hand, the magnitude of the voltage has a far greater effect on conductive than on resistive minerals. Shiou-Chuan Sun (authors' reply)—Thanks are extended to Drs. Ralston and Fraas for their keen interest in this paper. Their questions concerning coal dust,

Jan 1, 1951