Search Documents

By A. H. Larson, R. J. McClincy

The activity of Sb,03 in PbO-Sb,03 slags containing less than 50 mol pct Sb,03 was determined by the inert-gas saturation method at 700°C. In this composition range, the activity gf SbzO3 shows a strong negative deviation from ideality. The activity of PbO in these slags was calculated by application of the Gibbs-Duhem iniegration to the Sb203 activity data. The calculated activity of PbO in slags containing more than 63 mol pct PbO was found to deviate in a positive direction from ideality uthile a negative deviation was found for slags containing less PbO. The standard Gibbs free energies of formation of Sb,03 and PbO. Sb203 have been calculated and compared with existing data in the literature. The activity of Sb203 in PbO-Si0,-Sb203 (PbO/SiO, = 2) slags containing less than 25 mol pct Sb,03 was also determined by the inert-gas saturation method at 700°C. In this composition range, the activity of Sbz03 shows a very large negative deviation from ideality. VERY little experimental work has been published in the past to determine equilibrium data in the oxide systems connected with the refining of lead. These data are of value since impurities such as antimony, arsenic, and tin must be removed from lead and recovered for further treatment. Equilibrium studies on antimony and arsenic systems are also of interest for the design of new processes for lead refining and lead dross treatment. Maier and ~incke' first determined the liquidus curves for the PbO-Sb203 system and identified the compound PbO . Sb203. They found the phase diagram for this system to be two simple eutectics located on either side of the congruent melting compound. They also determined a very limited amount of vapor pressure data for Sb406 abbve PbO-Sba3 melts at 697"~. A second phase diagram investigation on this system was reported by Hennig and Kohlmeyer' who confirmed the existence of the compound PbO . Sb203 as well as the form of the diagram. A disagreement was noticed, however, in that their liquidus temperatures over nearly the entire composition range were higher than those reported by Maier and Hincke. Barthel~ and pelze14 redetermined the liquidus curve at the PbO-rich end of the PbO-Sb@, system and agreed very closely with the results of Maier and Hincke. None of the investigators mentioned above reported any mutual solid solubility in the PbO-SbD3 system. Zunkel and Larson5 have determined the phase diagram for the PbO-rich end of the PbO-Sb203 system by slag-metal equilibrium studies in the Pb-PbO-Sb203 system and by thermal analysis studies in the PbO-Sbz03 system. A maximum solid solubility of 5.6 mol pct Sb203 in PbO was observed at the eutectic temperature of 604°C. Their results for the phase diagram agree favorably with those of Maier and Hincke. The vapor pressure of Sb2O3 in the temperature range from 470" to 800°C has been determined by Hincke, using a modification of the transportation meth~d.~ His results for temperatures below the melting point of Sba3 are the only data reported in the published literature. The predominant vapor species has been shown to be Sb,06 by Norman and staley.? Myzenkov and Klushin,8 using the boiling-point method, have determined the pressure of Sb406 above liquid SbD3 in the temperature range from 715" to 1025°C. The agreement between these two studies is not very close. A portion of the discrepancy lies in the fact that Hincke used silica crucibles, which were attacked by the liquid Sbz03 at high temperatures. This fact does not account, however. for the large difference observed at the melting point. ~aier' gives a brief summary of vapor pressure data for Sb,O, above pure liquid Sbz03 which agree quite well with the data of Myzenkov and Klushin at temperatures near the melting point. This paper describes the determination of Sb2O3 activity data in the PbO-Sb203 and Pb0-Si02-Sb203 (PbO/SiOz = 2) systems by the inert-gas saturation method. These activity data are compared with the data calculated by Zunkel and arson. EXPERIMENTAL Materials. The materials used in this investigation were analytical reagent-grade PbO (99.8 pct PbO, 0.14 pct insoluble in CHsCOOH, 0.02 pct not precipitated by HB, 0.1 pct CaO, and 0.08 pct SiOz), Sbf13 (99.6 pct Sb203, 0.004 PC~ C1-, 0.005 PC~ SO;-, 0.15 p~t AS, 0.001 pct Fe, and 0.03 pct other heavy metals such as Pb), and SiOz (chromatographic grade). Apparatus for Vapor Pressure Determinations. The apparatus used in this investigation consisted of a transportation reaction system with two separate gas trains. The argon transporting gas was first mixed with a small amount of hydrogen, metered, and dried by passage through silica gel and anhydrone drying tubes arranged in series. After this preliminary drying, the argon was passed through copper wool at 500°C to convert the residual oxygen to water vapor which was removed by three anhydrone drying tubes. A second stream of argon was metered and dried and then passed around the outside of the alumina reaction tube to flush away the volatile species to pre-

Jan 1, 1970

By G. L. Tufford, R. L. Bleifuss

Low-grade manganiferous iron ores of Minnesota's Cuyuna Range, in general, do not respond to conventional mineral dressing techniques because of their fine-grained texture. Reducing these ores to magnetite with subsequent magnetic separation and flotation have not given satisfactory results because, in many instances, concentrate grade and manganese recovery are low. Metallization of iron and concurrent reduction of higher manganese oxides to MnO, as in the R-N process, followed by recovery of iron by magnetic separation and manganese by leaching, seems to be a technically feasible process. High-temperature x-ray diffraction studies show that solid-state reactions between iron and manganese, with the formation of intermediate iron-manganese oxides, occur during reduction and affect recovery of both iron and manganese from the final product. Solid state reactions also occur between FeO, MnO, and SiO, at temperatures as low as 900°C. The kinetics of these reactions are such that they become an important factor in the treatment of ores by the R-N process. These investigations suggest a temperature and gas composition cycle that would maximize both iron and manganese recovery. During the past ten years, iron ore shipments from the Cuyuna Range of Minnesota have decreased sharp1y. Because of adverse grade, structure, and cost, many Cuyuna ores are no longer competitive with high-grade foreign ores and domestic pellets. The low-grade manganiferous iron ores from the Cuyuna Range, in general, do not respond to conventional mineral dressing techniques because of their fine-grained texture. Reducing these ores to magnetite for subsequent magnetic separation and flotation has not given satisfactory results because concentrate grade and manganese recovery are often low. However, a technically feasible process appears to be metallization of the iron and concurrent reduction of manganese oxides to MnO with recovery of metallic iron by magnetic separation and extraction of manganese from the tailings by leaching. In 1962 the R-N Corp., with a grant from the Area Redevelopment Administration, conducted an amenability study of the metallization of manganiferous iron ore from the Cuyuna Range. The results of this preliminary investigation were sufficient to interest the Economic Development Administration in sponsoring further studies of the process with emphasis on secondary recovery of manganese from the nonmagnetic tailings. Inasmuch as the metallization process has considerable influence on the final form of the manganese - its texture and distribution between the magnetic concentrate and nonmagnetic tailings-the investigation included a study of metallization of the ore as well. Therefore, the investigation conducted at the Mines Experiment Station covered three interrelated phases: (1) laboratory R-N roasting studies and magnetic separation tests, (2) laboratory chemical extraction experiments of the nonmagnetic tailings, and (3) a mineralogical study of the crude ores and their various roast products. High-temperature x-ray diffraction investigation of the Fe-Mn-Si0,-0, system is the main topic of this paper and an extension of the mineralogical work. GENERAL GEOLOGY The Cuyuna Range is known for its complicated geologic structure, complex orebodies, and generally indifferent response to attempts at conventional beneficiation. Several geologists have made intensive studies of the Cuyuna Range, including Leithl (1907), ~darns' (1910), Zapffe3 (1925), Grout and Wolff4 (1955), and schmidt5 (1963), whose study was the most comprehensive of all. The Range is covered with glacial deposits - till, out-wash, and lake sediments -up to 250 ft thick. Bedrock stratigraphic units of the Cuyuna Range consist of three tightly folded Precambrian sedimentary formations. The lower unit is the Mahnomen formation, composed of 2000 or more feet of argillite, slate, siltstone, and quartzite. The middle unit is the Trommald formation, which varies from 45 to 500 ft in thickness and comprises the major iron-bearing formation. The upper unit is the Rabbit Lake formation, consisting of over 2000 it of argillite, slate, and interbedded lenses of lean iron formation. In the central part of the Cuyuna Range, the units have been folded into a series of

Jan 1, 1969

By W. V. Swarzenski

In its effort to combat waterlogging and soil salinity, the Water and Soils Investigation Division of WAPDA (West Pakistan's Water and Power Development Authority) has carried out an extensive program of test drilling andwater sampling since 1954. Data collected during the past ten years have permitted the delineation of fresh and saline groundwater zones in the Punjab Plain. Fresh groundwater containing generally less than 500 ppm of total dissolved solids is found in wide belts paralleling the major rivers and in other areas of fresh-water recharge. Locally, fresh groundwater extends to depths of 1500 ft and more. Saline groundwater occurs down gradient from sources of recharge, particularly in the lower central parts of the interfluvial areas, and presumably underlies most of the Punjab Plain. The groundwaters of the Punjab are characterized by their evolution from calcium, magnesium bicarbonate waters near sources of recharge to waters containing a dominant proportion of sodium. The highly mineralized waters of the Punjab are generally of the sodium chloride type, whereas in the Dera Ismail Khan District, sodium sulfate waters predominate. The pattern of distribution of saline groundwater zones and the observed gradual increase in mineral content, down gradient from sources of recharge, can be explained best by a hypothesis stressing the process of evaporation from the water table and solution of minerals within the alluvial aquifer. In 1954, detailed groundwater surveys in the Punjab Plain were initiated by WASID, the Water and Soils Investigation Division of West Pakistan's Water and Power Development Authority. The investigations, undertaken under a cooperative agreement between the governments of Pakistan and the United States, were aimed at the formulation of reclamation measures to improve waterlogged and saline soils, and to assess the groundwater potential of the Punjab and other areas of West Pakistan. The nature and urgency of WASID's primary task limited the exploration of the alluvial aquifer generally to its uppermost part. About 1030 test holes drilled in 47,000 sq miles of the Punjab defined the nature of the alluvium to depths of about 600 ft and yielded data on water quality to 400 or 500 ft. A report on the hydrology of the Punjab, based on the results of these investigations was published by WASID in 1963.' The present report incorporates data obtained by WASID since 1962 in a program of deep test drilling in the Punjab and the adjacent areas of Bahawalpur and Dera Ismail Khan District, permitting the definition of fresh and saline groundwater zones to depths of 1500 ft in some areas. Groundwater in the Punjab Plain is contained in alluvial deposits, predominantly sand and silt, which extend almost everywhere to depths of 1000 ft and more. The alluvium has been deposited by the Indus River and its tributaries since late Tertiary time and is contiguous with similar deposits in India. The Indo-Gangetic Plain extends from the foothills of the Himalayas to the ancient rocks of the Peninsular Shield in central India and to the ocean. Gradients are generally very low and range from about 1% ft per mile in the upper part of the plain to less than 1 ft per mile in the south and southwest. The monotony of the alluvial plain is broken by scattered bedrock outcrops in two of the interfluvial areas, Chaj Doab and Rechna Doab. The bedrock hills are projections of the northwest-trending Delhi-Shahpur Ridge that is largely buried by alluvium. The rocks of the buried ridge, presumably of Precambrian age, are essentially impermeable and define the lower limit of the alluvial aquifer in parts of Chaj, Rechna, and Bari doabs. Elsewhere in the Punjab, there are no outcrops of other consolidated rocks and their presence below the alluvium is conjectural. The principal areas of bedrock outcrops, near Kirana and Sangla, are shown diagrammatically in Fig. 1. The movement of groundwater through the alluvial aquifer of the Punjab has been described by Green-man and others.' In most of the area, the pre-irriga-tion water table sloped from the rivers downstream and toward the central axes of the doabs, indicating that the rivers were sources of groundwater recharge. As a result of seepage from irrigation canals, water levels have risen as much as 90 ft. In 1960 they were within 5 to 15 ft of the land surface and above the

Jan 1, 1970

By L. D. Lash, J. R. Ross

Discovery of scandium in the Vitro solvent extraction plant for uranium led to commercial recovery of the byproduct. Micro amounts of scandium were extracted with uranium by dodecyl phosphoric acid, but failed to follow ura-niuminto the hydrochloric acid strip solution and were eventually concentrated in the organic extractant. A fluoride strip system was developed to recover scandium from the solvent in concentrated form. High purity scandium oxide was then prepared in multi-pound lots by chemical separation techniques. The plant recovery operation, final product purification, and analytical procedures are described. Scandium is a pseudo-rare earth which is truly rare and expensive. It has special properties which may make it desirable even at the present price of $2750 per lb. Recently the price was lowered from $5000 per Ib which had prevailed since 1952, and it is anticipated that usage will be stimulated because of the lowered price. This metallic element is distributed widely in trace amounts in the rocks of the earth's crust. In addition to micro-amounts found in most uranium ores, concentrations of 50 to 100 ppm have been found in Colorado ferberite ore, lateritic nickel ore, heavy sandstone from Utah, Wyoming, and New Mexico, and various zircon sands and monazites from the western part of the U. S. Scandium has been found as an essential constituent of very few minerals, the most important being thortveitite, a scandium silicate. At the present time, this mineral commands a price more than twice that of gold. Chemically, scandium is in group 3A of the periodic table. It is closely associated with yttrium and the rare earths which it strongly resembles in its reactions. It has a valence of three and will form an insoluble hydroxide, fluoride, or oxalate under proper conditions, similar to the rare earths. Eight years before its discovery, scandium was predicted by Mendeleef who ascribed his eka-boron with properties nearly identical to the actual properties of scandium. Its position as the element with Atomic No. 21 and Atomic Weight 44.96 places it between calcium and titanium in Period 4 of the chart. The successful commercial application of scandium must depend on unique properties to justify use of this high cost substance. Greater consumption would allow additional price reductions, but scan- dium will remain a relatively high-priced commodity because of its inherent scarcity. Research reportedly has been oriented toward use of scandium as an agent to achieve high-temperature, low-density alloys with magnesium and tantalum.' Also, the U.S. Air Force sponsored a project for production of research amounts of pure scandium metal.' The oxide has been used experimentally in electronics, ceramics, and metallurgy. The various aspects of scandium are well covered in recent publications.s-5 CONCENTRATE RECOVERY Small amounts of scandium exist in uranium ores and are dissolved during an acid leach yielding up to 0.001 gpl Sc2O9. When Vitro converted their uranium plant from phosphate precipitation to solvent extraction: scandium was found to follow the uranium into the dodecyl phosphoric acid solvent (DDPA). However, scandium did not strip with uranium from the DDPA in hydrochloric acid, but remained in the solvent. Therefore, a concentration of scandium built up in the organic phase. Residues from the solvent were spectrographed by the U.S. Bureau of Mines and found to contain scandium. As a result of this discovery, provisions were made in the plant for recovery of scandium-bearing concentrates. Solvent extraction of uranium was added to a conventional acid leach process in a typical installation? The ore was crushed and ground, and then leached with dilute sulfuric acid. Addition of an oxidant such as sodium chlorate insured conversion of uranium minerals to a soluble form. At this point, the slurry was chemically reduced by a sulfide, such as sodium hydrosulfide, to remove substances such as ferric iron and molybdenum which were partially extracted by the solvent. The solids-liquid separation was accomplished by a four-stage counter cur rent decantation (CCD) thickener circuit. The uranium was extracted from pregnant liquor with 0.1M DDPA in kerosene and stripped with ION

Jan 1, 1961

By Alan J. Strauss

The Group IV elements germanium, tin, and lead form nine 1:1 compounds with the Group VI elements sulfur, selenium, and tellurium. This paper reviews the properties of the pseudobinary solid solutions formed by these compounds, including the extent of mutual solid solubility, temperature-composition phase diagrams, transport properties, deviations from stoichiometry, optical properties, and energy band structure. Particular emphasis is placed on the Pbl-xSnxTe and Pb1-xSn,Se alloys with rocksalt structure, because of current interest in these malerials for generating and detecting infrared ,radiation. ThE Group IV elements germanium, tin, and lead form nine 1:1 compounds with the Group VI elements sulfur, selenium, and tellurium. Some of the physical and electronic properties of these compounds, including their melting points1-8 and energy gaps,4'9-12 are listed in Table I. Four compounds (SnTe, PbS, PbSe, and PbTe) have the cubic rocksalt (Bl) structure. At room temperature GeTe has a rhombohedra1 structure closely related to the B1 structure, into which it is transformed at about 400°C. Four compounds (GeS, GeSe, SnS, and SnSe) have the orthorhombic B29 structure. In samples which have not been intentionally doped with impurities, the electrical conductivity is due primarily to electrons or holes produced by the ionization of donor or acceptor lattice defects associated with deviations from stoichiometry. Undoped samples of PbS, PbSe, and PbTe may be either n type or p type, depending on whether they contain excess lead or an excess of the Group VI element, respectively, but only p-type samples of the other compounds have been reported. This paper will review the properties of the pseudo-binary solid solutions formed by the nine 1:l compounds. The topics to be considered include the extent of mutual solid solubility, temperature-composition phase diagrams, transport properties, deviations from stoichiometry, optical properties, and band structure. Particular emphasis will be placed on the Pb]-xSnxTe and Pbl-xSnxSe alloys with B1 structure, which are promising materials for generating and detecting infrared radiation in the 8 to 14 µm atmospheric window and beyond. MUTUAL SOLID SOLUBILITY The extent of mutual solid solubility in the pseudo-binary systems has been investigated for fourteen of the eighteen ternary systems (in which the two terminal compounds have a common element) and for nine of the eighteen quaternary systems. In most cases, X-ray diffraction measurements made at room temperature were used to determine the structure and lattice parameter(s) of the phase(s) present in samples of various compositions prepared by freezing from the melt. In many investigations, including the extensive studies of Krebs and co-workers,13'14 the samples were annealed at elevated temperatures before X-ray measurements were made. In some cases, metallographic examination and thermal analysis have also been employed. The results for the ternary and quaternary systems are summarized in Tables II and III, respectively. (The original references should be consulted for the annealing temperatures.) The solubility of one compound in the other is at least 5 mol pct in all cases, and is often much larger. Complete solid solubility has been observed in all systems so far investigated in which the terminal compounds have the same structure, although in the PbS-PbTe system complete solubility is limited to elevated temperatures. Thus complete solid solubility occurs in five systems where both compounds have the B1 structure (SnTe-PbTe, PbS-PbSe, PbS-PbTe at temperatures above 805°C, PbSe-PbTe, and SnTe-PbSe) and in three where both compounds have the B29 structure (GeS-SnS. GeSe-~n~e-, and SnS-SnSe), as well as in two involving GeTe and a compound with B1 structure (GeTe-SnTe and GeTe-PbTe). On the basis of thermal analysis data, complete solid solubility at sufficiently high temperatures has also been reported for the GeSe-GeTe2 and SnS- pbS22 systems. This seems unlikely, however,

Jan 1, 1969

By A. E. Dwight

Lattice parameters were determined for eighteen equiatornic alloys of the CsCl-type structure, ten of which were previously un-reported. It was found that fomation of the CsCl-type structure in binary alloys of the transition elements is largely dependent on position of the elements in the periodic table. The relative size of the two elements was not found to be a controlling factor. A recent paper by Beck, Darby, and Arora1 corre-lates the occurrence of CsC1-type ordered structures with the position of the constituent elements in the periodic table for the first long period. It was also suggested that a definite increase in relative bond strength between unlike atoms occurred when, in binary alloys of iron-group elements, the other component is changed from a chromium-group element, to a vanadium-group element, to titanium. A later paper by Philip and Beck2 noted that the lattice contraction increased in the order CrFe, VFe, and TiFe. It was also noted by Philip and Beck2 that the lattice contractions of CsC1-type alloys decreased in the order: TiFe, TiCo, and TiNi, which is an apparent reversal of the contractions expected from the position in the periodic table. It was suggested that the increasing lattice contraction is an indication of increased stability, i.e., greater A-Bbond strength. The present investigation was carried out to determine whether the relation of the position in the periodic table to the formation of the CsC1-type structure was also correct for alloys involving the second and third long-period elements. A systematic search was made for CsC1-type structures among equiatomic alloys and for those found, the lattice contraction was determined. EXPERIMENTAL TECHNIQUE The elements Y, Gd, Ti, Zr, Hf, V, and Cb are designated the A group and the elements Mn, Re, Fe, Ru, Os, Co, Rh, Ir, Ni, Pd, Pt, Cu, Ag, and Au are designated the B group. Equiatomic alloys were prepared for 57 AB combinations. The alloys were arc melted in a multicrucible furnace3 in buttons ranging from 5 to 20 g. Chemical analyses were not made, as the charge weights agreed closely with those of the buttons after melting. The alloy buttons were homogenized at 800° to 900°C. Metal log raphic and X-ray specimens were prepared and heat treated at temperatures from 600° to 1200°C. Specimens for X-ray diffraction were usually ground to a powder in an agate mortar; however, needle-shaped solid specimens were used when the alloy was sufficiently ductile to permit their preparation. Diffraction patterns were taken with a Straumanistype Debye-Scherrer camera using filtered Cu or Co radiation. The lattice parameters were obtained in A by plotting the calculated a0 values against the cos29/sin 0 + cos2?/? function and extrapolating linearly to ?= 900. Metallographic control specimens were polished on cloth wheels with diamond paste and etched with various phosphoric and nitric acid reagents. RESULTS The eighteen equiatomic alloys listed in Table I gave evidence of a cubic structure with two atoms in the unit cell, although two of these cubic structures exist only at elevated temperatures and transform to a tetragonal structure on quenching. Nine of these eighteen alloys gave diffraction patterns with super-lattice lines showing that the structure is of the CsC1-type. The lack of superlattice lines in patterns of the other nine alloys may be attributed to the small difference in atomic scattering power of the components. Metallographic study indicates the occurrence of nine narrow single-phase fields at the AB composition. Any or all of these nine may also have a CsC1-type structure. The VFe alloy was found to have a CsCl-type structure by Philip and Beck2 through the use of CrKa radiation (for which the scattering factor of V is anomalously low), whereas the Cu radiation used

Jan 1, 1960

By C. J. Leith

A study of the effect of rock composition, rock structure and degree of weathering on the stability of cut slopes is being sponsored jointly by the U.S. Bureau of Public Roads and the North Carolina Highway Commission. In 58 mountain and piedmont counties of North Carolina the percentage of failed cut slopes is greatest in micaceous metasediments, gneisses, and schists, and in saprolite and soil derived from these rock types. Soil slope failures outnumber rock slope failures by two to one. Joints and similar planes of separation exert a strong influence on size and shape of the sliding mass. They may or may not act as failure surfaces, depending on their orientation with respect to the active forces. Climatological data, though indicative of weathering conditions, do not correlate well with slope failure frequency. Because of the presence of joints and similar planes of weakness in soil and rock materials, conventional methods for analyzing slope stabilities are not directly applicable. Empirically derived modifications of these methods are being investigated. A study of the stability of highway cut slopes, sponsored by the U. S. Bureau of Public Roads and the North Carolina State Highway Commission, began in 1962 at North Carolina State of the University of North Carolina at Raleigh. As part of this study all slides, rockfalls and other types of cut slope failures on Federal and State highways in the 58 mountain and piedmont counties in North Carolina were located and described, and the data catalogued in a punched card file system. A major objective of the project is to relate slope failures to properties and physical conditions of the geological units in which the slopes were constructed, and to correlate soil type and/or geological unit with type and frequency of slope failure. The complexities of the problem of slope stability and the limitations which these complexities impose on methods for analyzing slopes have been recognized for many years. A great variety of factors and processes may lead to slides, often making it almost impossible to analyze theoretically the conditions required for stability of slopes. One of the principal factors determining maximum safe slopes is the shear strength of the material in which the slopes are cut, but unfortunately there are very few data available concerning shear strengths of residual soils. Vargasl tested clay derived from gneiss and granite in southern Brazil; the properties of decomposed granite occurring near Hong Kong were determined by Lumb.2 These data are being used, when applicable, to supplement the test data obtained in the present study by Yorke.3 The locations of the North Carolina slope failures, more than 400 in number, are shown on Fig. 1. This map, adapted from the Geological Map of North Carolina,4 suggests the possibility of a relationship between frequency of slide occurrence and rock type. However, the evaluation of this possibility requires consideration not only of the type of rock, but also of its large and small scale structural features, its susceptibility to and degree of weathering, and the composition and structure of the weathering products. Soil slope failures in thoroughly weathered soil material and saprolite outnumber rock slope failures two to one. INFLUENCE OF ROCK TYPE The agricultural soil type involved in each soil slope failure was identified and each failure was catalogued in terms of the parent material from which the soil was derived. These data indicate that most of the slope failures, whether in the rock or in the derived soil, are associated with metamorphic rocks (see Fig. 2a). The data may be skewed somewhat because of the relative sizes of the total areas underlain by the various rock types, but Leith and Gupton5 have demonstrated that the preponderance of failures in metamorphic rocks is of much greater magnitude than could be accounted for by the areal factor alone. The dominance of metamorphic rocks is emphasized when soil slope failures are considered in terms of the specific rock types from which the soils were derived (see Fig. 2b). In particular, mica schists and mica gneisses account for more slides

Jan 1, 1965

By R. Stickler, A. Vinckier

An optical and electron microscope study was made on a commercial 302 stainless steel heat treated for massive carbide precipitation. Convincirg evidence was obtained that the grain boundary precipitate does not grow away from the grain boundary into the matrix, but grows as a network of large thin dendrites in between the grains. IN austenitic stainless steels the carbon in supersaturated solution precipitates when the steel is heated in the temperature range 450" to 1000°C. During such heat treatments the chromium-rich carbide occurs primarily at the grain boundaries and has adverse effects on the corrosion resistance and low-temperature ductility of the material. It has been shown that the morphology of the precipitated particles differs widely depending on the time and temperature of the heat treatment, the nature of the boundary, the misfit between the grains, and so forth.1"5 It was assumed by Mahla et al.,' Streicher,' and Mc Nutt' that the carbide particles which nucleate in the grain boundary grow in various geometric or dendritic forms away from the boundary into the matrix. However, Kinzel,' Hatwell et a, and Plateau et aL4 found that the particles nucleate in the grain boundary and grow as a network of thin dendrites in the grain boundary interface. We have made a comprehensive studyg of the precipitation occurring in a commercial 302 austenitic stainless steel heat treated for times ranging from 0.15 to 1500 hr at various temperatures from 480" to 1065"~. This study was made to elucidate the influence of heat treatments on both the mechanical and the corrosion properties of this steel. Part of this investigation which is pertinent to the morphology of the grain boundary carbides referred to above is separately reported here. We found that the particles which nucleated in the boundaries grew in the interface of these boundaries, thus supporting the viewpoints of Kinzel,' Hatwell et al.,3 and Plateau et al.4 Furthermore, when carbide particles nucleated in the matrix very close to the boundaries, they possessed a morphology distinctively different from the particles growing in the grain boundaries. MATERIAL A study of metallographic samples and of fracture surfaces of a 302 stainless steel is reported in this paper. The composition and heat treatments are listed in Table I. Polished and etched samples were examined und813r the optical microscope, and carbon extraction replicas of etched micrographic samples and various fracture surfaces3'8'9 were examined under the electron microscope. RESULTS AND DISCUSSION A representative optical micrograph of the 302 steel, condition A, is shown in Fig. l(a). Particles can be seen on the grain boundaries but no traces can be found of particles which grow from the grain boundaries into the matrix. A carbon extraction replica of this sample shows numerous large thin dendrites, Fig. l(b). The lateral dimension of such carbide particles vary up to 100 p, and their thickness estimated from the amoun! of electron penetration i:; between 500 and 1000A. Such large dendrites are extracted from almost all grain boundaries and, if they had grown into the grains, they would definitely be revealed by etching traces in the matrix, Fig. l(a). The reason why these large dendrites on the extraction replica appear to be grown into the grain is due to the mechanism of the extraction replica process. Thus, these dendrites are supported by the carbon replica film only at the edges originally along the grain boundary trace A-A, Fig. l(b), in the polished metal section and have subsequently fallen over onto the carbon replica film during handling. Although such dendrites generally fall only to one particular side of the grain boundary trace, one finds occasionally that parts of a dendrite have fallen to both sides, as shown in Fig. l(b). Further evidence for the growth of carbide in the grain boundary can be obtained from the appearance of fracture surfaces. A small impact specimen of the 302 steel, condition A, was broken at liquid nitrogen temperature. The fracture path follows the

Jan 1, 1962

By J. L. Jorstad

The hypereutectic Al-Si alloys 390 and A390 have wear characteristics superior to any of the more common aluminum casting alloys. This excellent wear resistance, coupled with good mechanical properties, high hardness, and low coefficient of thermal expansion, has made these alloys candidates for the all-aluminum internal combustion engine, the application for which they were primarily developed. A390 alloy is intended for sand and permanent mold casting, and requires a lower iron ccxltent (0.5 pct maximum) than its die casting companion 390 alloy (0.6 to 1.1 pct Fe). The 17 pct nominal silicon in these alloys provides sufficient quantities of the hard primary silicon phase to assure a high degree of wear resistance, yet little enough of this phase, to minimize the casting and m achining problems associated in the past with the hypereutectic alloys. The mechanical and physical properties of 390 and A390 alloys are competitive with the best of the common aluminum casting alloys with the exception of low ductility. This low ductility is not considered a detriment, since in many applications these alloys replace cast iron. Corrosion resistance is similar to the standard alloys 380 and 333. Numerous parts, of varying degrees of complexity, have been cast of alloys 390 and A390, including engine blocks and heads. The deviations from normal good handling and casting practices that are required for the alloys are those associated with the presence of the primary silicon. To obtain optimum strength and machinability, the molten alloys should be treated with phosphorus to refine the primary silicon phase. Care must be exercised to properly control the pouring temperature and rate in order to minimize primary silicon growth and segregation. AUTOMOTIVE engineers have for years recognized the advantages of lighter weight and better heat transfer that aluminum could offer as material of construction for engine blocks. These advantages alone, however, are insufficient justification for acceptance of aluminum engines by the automotive industry. To be acceptable, an aluminum engine first must pass all tests to which cast-iron engines are subjected, and, in addition, must represent no cost penalty in manufacturing. None of the conventional aluminum casting alloys have sufficient wear resistance to withstand the tests to which cast iron is subjected as a cylinder bore material, and recent attempts to manufacture aluminum engines with cast-in-place iron sleeves could not compete costwise with the equivalent cast-iron engine. The prerequisite to an acceptable aluminum engine seemed to be a casting alloy with a high degree of wear resistance that would eliminate the necessity of cast-in iron sleeves or liners. The hypereutectic A1-Si alloys 390 and A390 have met this challenge.' Combined with modified pistons and a patented cylinder bore surface finish,2 the performance of these alloys in more than 1300 cold start and cold scuff tests, over 3500 hr of dynamometer wear and endurance tests, and more than 350,000 miles of road tests leaves no doubt as to the feasibility of running on bare aluminum cylinder bores. ALLOY DEVELOPMENT The desirable characteristics of the hypereutectic A1-Si alloys have been recognized for some time. Their excellent wear resistance and low coefficient of thermal expansions have been used to advantage in the production of diesel-type pistons in Europe and to a limited extent in this country. The major contributor to the good wear resistance of these alloys is the extremely hard primary silicon phase in the microstructure. Although the percent silicon used experimentally has been much higher, most commercial alloys have ranged from about 14 to 25 pct. Generally, as the silicon content is increased, wear resistance increases, and the coefficient of thermal expansion decreases. With increases in silicon, however, machinability and cast-ability tend to suffer. The development of a satisfactory aluminum engine block material at Reynolds involved the testing and evaluation of many alloys, covering a wide range of silicon contents and numerous variations of iron, copper, magnesium, manganese, and other alloying additions. Castability, mechanical and physical prop-

Jan 1, 1969

By T. F. Bower, M. C. Flemings, H. D. Brody

A series of experiments are reported which show thai reasonable assumptions for analysis of solute redistribution in solidification of castings and ingols illclr(de: negligible undercooling before nuclcation of solid phases, negligible increase of solute in advance of the tips of growing dendrites, complete diffusion within the Liquid oer distances the order, of dentrite arm spacings, platelike dentrite t/o?$holog?.. Qzmli/ali,e and periment is obtained JOY Al-Cu alloys front measurements of amount of nonequilibrium second phase, minimum solute content at the centers dentrites arms (after solidification), and 3) change in minimum solute content in dentrite arms during solidification. In a previous paper' analyses were given describing solute redistribution in dendritic solidification. The analyses were undertaken primarily to permit prediction of "severity of microsegregation" in a casting or ingot after solidification and cooling to room temperature, but can also be used to predict "local fraction solid' as a function of temperature in the solidifying alloy. Numerical results were given for Al-Cu alloys. The aims of this paper are to examine the validity of some of the assumptions of that analysis, and to compare predictions of the theory with experiments. All experiments reported are on Al-Cu alloys, the bulk on Al-4.5 pct Cu alloy. EXPERIMENTS Experiments conducted were on small ingots, 41/2 in. in diam by about 10 in. high. solidified in a controlled thermal environment (i.e., in a resistance-heated, re-circulating air furnace, whose temperature could be controlled to 1°C). In one series of experiments, the ingots were solidified very slowly (solidification time was varied from 8 to 1000 hr) and at constant rate of heat extraction. In a second series of experiments the ingots were solidified ( 'unidirectionally". Fig. 1 is a sketch of the method of making the two different types of ingots. The unidirectionally solidified ingots were fully columnar, and the slowly solidified ingots had equiaxed structures, Fig. 2. In making the slowly solidified ingots, the mold employed was carbon steel, coated with inert refractory. Typically the mold and its environment were heated to 700°C. The molten alloy was then poured into the mold and the temperature of the system equilibrated above the liquidus. The environment of the mold was next cooled with a controller responding to a differential thermocouple that measured the difference between the temperature of the melt and the temperature of the mold environment. The differential thermocouple consisted of one chromel-alumel junction in the melt connected in opposition with a second junction in the furnace. The potential across the differential thermocouple was input to the controller which acted to keep this potential at a set. constant value; hence the temperature difference between the two junctions was maintained nearly constant. Major resistance to heat flow in the above apparatus was between the metal surface and the furnace atmosphere, not in the metal itself. By maintaining a constant temperature difference between the metal and the furnace atmosphere, the controller maintained an essentially constant rate of heat extraction during solidification, regardless of amount of heat released by the metal per unit temperature change. When the metal temperature dropped just below the eutectic temperature. the ingot was removed from the furnace and water-quenched. The unidirectionally solidified ingots were cast in a similar mold to the foregoing except that provision was made to extract heat through the bottom face of the mold by passing air or water through the mold base, Fig. 1. For these experiments, metal and mold temperature were again equilibrated above the liquidus. Temperature of the mold environment was then held

Jan 1, 1967

By Lincoln F. Elkins

The Spraberry Trend Field of West Texas was discovered in January, 1949. Drilling of 2.234 wells and production of some 45 million bbl of oil by January, 1953, indicated this to be an important field which will ultimately cover more than 400,000 acres. In addition to being the world's largest field in areal extent, the Spraberry has presented many problems in well completion and operation and has demonstrated unique reservoir performance characteristics. The pay section consists primarily of a few fine grained sandstone or siltstone members in a thousand-ft thick section of shale, limestone. and siltstone. Since porosity averages only 10 per cent and nearly all permeabilities are less than 1 md, conventional core analysis does not delineate the "pay" section. Mercury injection was used as a capillary pressure test adaptable to rapid routine use to select those intervals having low enough connate water saturation to contain commercially significant oil saturation. In the central area of the field this "pay" amounts to 16 ft of Upper Spraberry and 15 ft of Lower Spraberry sands. An interconnected system of vertical fractures, observed in cores, provides the flow channels for oil to drain into the wells hut most of the oil is stored in the matrix since the void volume of fractures is estimated to be less than 1 per cent of that in the sand. Initial potentials of wells range up to 1.000 B/D after fracture treatment which should be compared with estimated capacity of 5 to 10 B/D if oil had to flow into the wells through the sand itself. Without exception initial pressures of later drilled wells were significantly lower than initial pressures of earlier drilled nearby wells in a large area some 6 miles long. This means the earlier drilled wells had drained fluids from areas much greater than their 40-acre proration units. Since most of this performance occurred while the reservoir pressure was above the. saturation pressure it was analyzed by the compressible fluid flow theory. This analysis gave calculated initial presrilres which agreed within 30 psi of measured pressures of 60 per cent of wells in the area using 16-md permeabilitv corresponding to a fracture system substantially that indicated by cores and using combined compressibility of rock and its contained oil and water corresponding to the core analysis data. The most important feature of this analysis was the very close agreement between effective compressibility of the rock and its contained oil and water from the field performance and that from the core tests, because it meant there are no "islands" of low permeability reservoir rock left untapped in the inter-well area and thus no additional wells are necessary to insure that at least one well penetrates each "reservoir." Twenty-five of forty-four 40-acre spaced wells on three contiguous sections were wed in a four-month inteference test. Six shut-in well. were tested monthly for oil production. productivity index. gas-oil ratio and pressure buildup, and seven shut-in wells were tested for decline in reservoir pressure. Tests on 12 regularly producing wells gave comparative data for interpretation of shut-in test wells. Reduction in reservoir pressure, decline in productivity index. and increase in gas-oil ratio were found to be substantially the same in the shut-in test wells as those in the comparative regularly producing wells, meaning that the producing wells were depleting the

Jan 1, 1953

By G. J. W. Kor, F. D. Richardson

The sulfide capacities a1 1500°C of slags in the systern CaO + CaF, +Al2O3 have been measured by bringing samples into equilibrium with gas mixtures made from CO + CO2 + SO, + N2. The capacities are negligzble both JOY CaF, and CaF, + Al2O3 melts but when lime is present even at 20 wt pct capacilies as high as 30 x lom3 can be obtained. The results have yielded information concerning the liquidus at 1500°C and fluoride-oxide melts in general. The slags used in electroslag refining contain substantial amounts of calcium fluoride. Robinson and Grainger' report that good results can be obtained by using slags of the approximate composition 70 wt pct CaF2 + 30 pct Al2O3. It has also been reported2 that a mixture of 50 pct CaF2 + 30 pct A12O3 + 20 pct CaO makes a good slag for general use. In view of the fact that very low sulfur contents are claimed for ingots produced by the electroslag process. studies have been made of the sulfide capacities [c, = wt pct S (PO2/Ps2)1/2 at 1500°C. of slags consisting of pure calcium fluoride, and of its mixtures with lime and/or alumina. These studies have also provided information on the phase diagrams. The slags were brought into equilibrium with gas mixtures prepared from NZ + CO + CO2 + SO2. Because CaFz is volatile and also easily hydrolyzed. measurements were made of its loss in weight in various flowing gas mixtures. EXPERIMENTAL Procedure. The apparatus and procedure were the same as described previously. Both platinum and iridium crucibles were used (height and inner diameter about 1 cm), but those made from iridium were stronger and able to withstand a greater number of experiments. In each experiment two crucibles were set in an alumina support and 1 g of slag mixture was divided between them. The materials from each crucible were analyzed separately after being brought to equilibrium with the gas, and then quenched in the water-cooled end of the reaction tube. Materials. Alumina and lime were prepared as de-scribed previously.4 Calcium fluoride was obtained by igniting Analar calcium fluoride in a platinum boat at about 800°C in a stream of pure dry nitrogen: the product was cooled in a desiccator. The slags were produced from mixtures of the powdered constituents, these being melted together in the course of each equilibrium experiment. The sulfur analyses and the X-ray diffraction meas- urements on the solidified slags were made as described previously.4 From the latter it appears that the CaF2 contained less than 0.5 mol pct CaO. RESULTS Values of (ps2/po2) for the Gas Mixtures. The re-sults have been represented in terms of (ps, /Po,)"? for the various gas mixtures used. The va1;es of this function at 1500°C are listed in Table I: they were calculated from the data cited previously for calculations at 1350°C 4 Weight Losses with CaF, and CaF, + CaO. The re-sults of the weight loss measurements* at 1500°C for

Jan 1, 1970

By B. B. Rath, Hsun Hu

Rates of migration of large-angle boundaries have been studied in zone-refined aluminum crystals, defonned 80 pct by rolling in the (110)[112] orientation at -78°C followed by a recovery anneal at 80°C. Artificially nucleated grains show a marked variation. by an order of magnitude, in their growth rates in different directions. The average activation energy for the migration of all boundaries was found to be about 16,000 cal per mole. The anisotropy of the boundary migration is rationalized on the basis of the boundary structure. It has been observed by Beck and HU,1 Kohara el al,2,3 and Czjzek and Haessner4 that recrystallized grains formed upon annealing Of deformed sing1e crystals of aluminum show anisotropic growth characteristics. Kohara et al. found that single crystals rolled in the (110)[112] orientation, when random nuclei were provided on one side of the crystal by rubbing with emery paper and annealing, developed a sharp recrys-tallization texture on the other side of the crystal upon further annealing. This sharp recrystallization texture consisted of four components, which were related to the deformation texture of the crystal, i.e. (110)[112], by rotations of ±40 deg around each of the two common [ 111] axes' They also noted that recrystallized grains were elongated in directions perpendicular to either of these two common [1111 axes. They attributed this anisotropic growth to the difference in the rate of self-diffusion or diffusion of impurity atoms along the tilt and the twist boundaries. A somewhat similar investigation was conducted by Czjzek and Haessner4 On strained single-crystal sheets Of alum- inum. These authors claimed that the matrix structure of the deformed crystal had a greater effect on the growth anisotropy of the recrystallized grains than did the boundary orientation itself. In the present investigation quantitative measurements of the rate of grain boundary migration in anisotropic growth have been made in zone-refined aluminum (99.9999+pct pure) crystals deformed 80 pct by rolling in the (110) 112] orientation. Crystals of this particular orientation were chosen because of the following desirable features: 1) the crystal does not change its orientation during rolling; 2) the rolling plane contains all the significant crystallographic directions; and 3) when annealed, following deformation, the crystal does not re-crystallize spontaneously but polygonizes to a stable and homogeneous structure. Hence, the initial orientation of the crystal and a constant strain energy in the matrix can be maintained during subsequent grain boundary migration studies. It is essential to keep the driving force constant for the study of boundary mobility.5 EXPERIMENTAL PROCEDURE A cylindrical single crystal of 1 in. diam was grown by the Bridgman method in a high-purity graphite mold. The resistance ratio, R(4.2°K) /R(298°K) , of the grown crystal was approximately 2.0 x 10-4. A number of slices, 1/4 in. thick, were cut from the crystal along the (110) plane and were mechanically and electrolyti-cally polished to remove the strained surface layer. The crystals were then rolled along the [112] direction to 80 pct reduction in thickness at -78°C. To minimize surface friction, the crystals were rolled between two layers of 0.005-in. teflon sheet. Rolling was interrupted, prior to completion, to remove the surface layers and the edges by electropolishing. These and similar precautions in handling the rolled crystals

Jan 1, 1967

By J. Skrove, C. R. Boardman

In situ permeability of the rock outside the Hardhat chimney was determined by pressurization of long holes with air. Experimental data indicated a remarkable difference between fracture permeability of the rock near the chimney and that at a considerable distance. Although permeable fault zones were known to exist in the granite stock, the measurements of background permeability were quite low, on the order of tenths to several millidarcies. The observed difference is about two or three orders of magnitude above this background in the region 125 to 215 ft radially from the shot point, or 80 to 165 ft radially from the vertical axis of the chimney. The presence of a collapsed drift immediately beyond this region precluded measurements which could have defined the maximum extent of the zone of high permeabilily. INTRODUCTION Previous exploration has revealed that contained nu-clear explosions create cavities which generally collapse, resulting in rubble-filled chimneys and annular fractured zones. These geometries have been shown to result in complex flow regimes which should increase the production rate from hydrocarbon reservoirs.' Empirical scaling equations have been developed for estimatina chimney radii and heights for a variet; of rock media.' The exten; of the annular fractured zone has been documented and associated permeability changes have been observed qualitatively for several explosions. This study was begun to establish the nature and magnitude of the permeability of the latter region. It is anticipated that results will be useful in estimating permeability changes and consequent production stimulation which might ensue from a contained explosion in a hydrocarbon reservoir. The post-shot environment of the Hardhat event (a 5-kt contained nuclear explosion in granitic rock) was c'hosen for the experimental measurements. The Hardhat device was detonated at a depth of 939 ft, and subsequent exploration revealed a chimney of broken rock with a radius of 65 to 70 ft and a height above shot point of 281 ft.' BeFore the explosion, the Hardhat medium was highly jointed and fractured (Fig. I). Jt was expected that differential rock motion along these and other weaknesses induced during cavity growth and collapse would significantly alter the permeability of the rock mass. EXPERIMENTAL METHOD Initially, three 2-in. diameter holes (Nos. 10, 12 and 19) were drilled about 25 ft outward through the walls of the 500-ft level drift (elevation 4,253 ft, Fig. 2). One was drilled near the chimney and two holes, one vertical and the other horizontal, were drilled near the shaft. Order-of-magnitude differences in permeability obtained by pressurization measurements indicated further: investigation was warranted. A series of 3-in. diameter holes was then drilled with water as a coolant into the walls and roof of the drift (Fig. 2). An 11-in. long packer was set from 1 to 8 Et inside each hole and air was injected at measured Row rates. Hole pressures were monitored at the collar. Permeability was low enough in the holes near the access shaft that pressure could be maintained long enough to obtain good pressure decay rates. In the vicinity of the chimney, however, permeability was so high that this was not possible and air was injected under steady-state conditions. About one year later, these same holes were retested to

Jan 1, 1967

By E. F. Sumner, C. K. Eilerts

A partial differential equation was developed and programmed to compute the cumulation and flow of the liquid phase of a gas-condensate fluid. It was found that such cumulation near the wellbore may attain saturations permitting liquid flow within periods of the order of 1 day. The radius at which this saturation obtains advances toward the external reservoir boundary with continued recovery, although it may move only 2 to 5 percent of that distance during the productive life of the well. This relatively high saturation can cause a serious dimunition in delivery capacity. The pressure dilferential required for flow of gas through a formation with such saturation may be as much as three times greater than the corresponding differential in a formation where saturation is less than 2 percent. Because of the radial geometry, total reservoir pressure differential required for flow with a zone of relatively high liquid saturation about the well was indicated to be two to three times greater than without the saturation. INTRODUCTION A computing program developed by the authors 1 to integrate the partial differential equation for transient radial flow of gas-condensate fluids required a prevalued function, W(Po) = kD(p0)/M(p0)z0(Po).......(1) related to cumulation of condensate in pores of the reservoir as pressure declines. Methods were available for relating mobility to saturation, saturation to liquid-vapor volume ratio, liquid-vapor volume ratio to pressure and, hence, mobility to pressure to obtain W(pD). However, certain assumptions had to be made in advance of program execution concerning movement of the liquid phase and change in radial distribution of liquid saturation as recovery progressed. Because reservoir fluid mobility and related pressure gradients are markedly dependent on liquid saturation, it was desirable to eliminate the necessity for these assumptions and in this respect improve the reliability of a result obtained by integration. Experimental research was begun to determine the relationship of variables that control the reservoir flow of low liquid-vapor ratio fluids. With the porous medium partly saturated, permeability to a two-phase flowing fluid could not be measured because the viscosity was unknown. Viscosity could not be measured without knowing permeability of the liquid-containing medium; but mobility, the ratio of permeability to viscosity, was measurable. This property, and liquid-vapor volume ratio of the flowing phases, have values determined by nature of the fluid and porous medium and, in addition, were found to be pressure, velocity and saturation dependent. A program developed by Kniazeff and Naville 2 for computing multicom-ponent, two-phase flow used polynomials to represent saturation dependence of permeabilities for gas and for liquid phases, and an effluent viscosity constant under reservoir conditions. The authors developed a program based on a partial differential equation of similar mass balance origin but designed to represent distribution of an unlimited number of components between gas and liquid phases utilizing the experimental information available as to variable dependence. Attention was given to liquid-vapor volume ratio of the flowing phases, a property which is essential as a liquid saturation boundary condition. A program for computing implicitly saturation increase at uniform intervals along the drainage radius was combined with an existing program for calculating pressures, and the two were used alternately in an iterative solution for both saturations and pressures. The function W(pD) needed for calculating pressures was replaced by the ratio of mobility to compressibility factor. BASIC EQUATIONS The partial differential equation for calculating

By M. C. Fuerstenau, A. M. Gaudin

A homogeneous suspension is viewed by X-rays. The radiation density seen, affords a measure of the extra absorption due to the solids contained. This radiation density, at a predetermined depth, varies with time. The chart of this relationship gives the desired determination. s it is frequently necessary to know the distribu-rt tion of particle sizes in various products used in industrial applications, a number of means have been devised for these determinations. Some of them include direct microscopic measurement, screening of product, extraction of samples from a settling slurry, air and liquid elutriation, adsorption of gases and liquids, and light absorption. The absorption of light as a means for particle size analysis has been known and employed for some time. X-ray absorption has not received the attention that light has enjoyed primarily because of the complex and costly instrumentation involved with X-rays. In 1954, Brown and Skrebowskil suggested the use of X-rays for this type of determination but did not supplement their suggestion with experiment. In 1958, the authors conducted size analysis experiments on suspensions of quartz with the Trans-viewer: an X-ray unit specifically adapted for sedimentation research, and Rossa conducted experiments in a similar manner in 1959 with a stable gamma emitter, AmZ4l, on suspensions of uranium oxide. To illustrate the applicability of X-ray absorption for analyzing particle size distributions, an essentially mono-energetic and well collimated X-ray beam was used as a source. The beam was made mono-energetic by placing a zirconium filter before the counting window together with feeding the pulses from the proportional counter into a reverter, a device capable of discriminating against pulses of various heights. The sketch in Fig. 1 shows the collimation arrangement in more detail. As shown, the X-ray beam was collimated by inserting a 3/8-in. ID pipe into one of the ports of the X-ray tube and further by two small steel plates with slits 3/32-in. wide and 1/2-in. long placed in front of the window of the Geiger-Mueller (G-M) tube. One of the plates was located 1/2 in. and the other 2 1/2 in. from the window of the counter; both plates were contained in an aluminum holder mounted on the box containing the G-M tube. This type and degree of collimation should eliminate any intensity due to scattered radiation; the transmitted intensity would then be solely a functior. of the absorption by the suspension at that level. Experimentally, homogeneous suspensions of finely ground quartz were prepared, Daxad (a sulfo-nated compound made from wood) was added as dis-persant, and the transmitted X-ray intensity measured as a function of time at a fixed depth in the suspension. In more detail, the experimental procedure involved the following: 1) measuring the transmitted X-ray intensity through the Daxad solution at a predetermined position or settling depth in the absence of solids, 2) placing a known amount of dry solids into the vessel and agitating thoroughly, 3) measuring the transmitted X-ray intensity at time zero (i.e., immediately upon cessation of stirring), and 4) measuring the transmitted X-ray intensity as a function of time (a 10-sec counting interval being chosen and counting being started 5 sec before the desired time). Since a linear relationship exists between percentage solid in a slurry and the logarithm of transmitted intensity for a homogeneous material, the cumu-

Jan 1, 1961

By V. B. Kurfman

Grain refinement of Mg-Al melts by carbonaceous additions has been attributed to nucleation by aluminum carbide. The effects of process and alloy variables are interpreted and predicted in terms of the dispersion and chemistry of this phase. The grain coarsening action of Be, Zr, Ti, R.E., chlorination, temperature extremes, and prolonged holding times is described. Measures necessary to insure an adequate dispersion of the catalyst are discussed. CARBON inoculation treatments have become fairly well known and used for grain refinement of magnesium alloys containing Al. Although there is general agreement that a nucleation process occurs, the process is not understood and the inoculants are used in a rather empirical fashion. The treatment is applied to the class of alloys containing 3 to 10 pct Al, i.e., AZ31A to AM100A. Typical methods involve melting, alloying, and adjusting the temperature to 1400° to 1450°F. Then 0.01 to 0.5 pct C as CaC2, C6C16, or lampblack is added by any convenient means, and the melt poured within 10 to 30 min. Investigators generally have been impressed by an assumed similarity of this refinement process to superheat grain refinement, which depends on heating approximately the same alloys to a temperature in the range of 1550" to 1650°F, then pouring promptly after the melt is cooled to the pouring temperature. Various predictions have been made that carbon refinement would replace superheating in commercial practice due to reduced process costs, but this replacement has not fully taken place because of production difficulties and conflicting observations. Davis, Eastwood, and DeHaven1 agree with Nelson2 and wood3 in suggesting that an excess of inoculant may be harmful. Wood however says that overtreat-ment is not a problem in production use of hexa-chlorobenzene inoculation, and Hultgren and Mitchell4 claim no evidence of harm from excess additions. Various grain coarsening reactions are known to occur, including the possibility of overtreatment mentioned above. Trace amounts of Be,2 Zr, and Ti may prevent refinement by either a carbon treatment or a superheat. Occasionally treatment with cl25 may cause coarsening, although the Battelle refinement process' uses a CC14-C12 blend. Grain coarsening also tends to occur on holding at temperatures below 1350°to 1400°F, especially after a superheat treatment, and for this reason Nelson2 stresses the desirability of a refinement method useful at lower temperatures for open pot melting practice. Since a carbon treatment can be made to work at temperatures below 1400°F, it seems desirable to investigate the mechanism of the refinement and the mechanisms of the coarsening reactions in order to establish control conditions for use in commercial production. The identity of the nucleating phase must first be established and then the factors affecting its chemistry and physical dispersion must be determined. THE IDENTITY OF THE NUCLEATING PHASE Davis, Eastwood, and DeHaven suggested that the nucleating phase in this system is Al4c3,1 but Mahoney, Tarr, and LeGrand8 disagree, largely because they found no evidence of the compound in alloys after carbon treatment and because there is no indication that aluminum carbide should be unstable over the temperature range used in the superheat treatment. This latter objection is based on the assumption that both the carbon treatment and the superheat treatment introduce the same nuclei. Electron diffraction studies have been made to identify the nucleating phase. Samples of grain refined A292 have been selectively etched SO that clean surfaces are obtained and so that secondary phases are in relief. Electron diffraction patterns from these surfaces have established that the carbon treatment of A292 introduces into the metal a large number of small, plate-like particles with a structure very similar to Al4C3. In most cases, the plate-like nature of the particles prevented positive identification but in the cases where the identification could be made the particles proved to be AIN A14C3. However, enough variation in lattice constants was observed so that all compositions from pure A14C3 to the 50:50 solid solution A1N.Al4C3 were probably present.14 In A14C3 and especially AlN.Al4C3 the A1 atoms occur in layers within which they have the same hexagonal symmetry and spacing as the Mg atoms in a single basal plane of a magnesium crystal. The solid solution spacing lies between the 3.16 of AIN and the 3.3? for Al4C3, in satisfactory agree-

Jan 1, 1962

By R. E. Maringer, B. A. Wilcox, A. H. Clauer, J. H. Sovik

Internal friction measurements from 25° to 1100°C have been made on specimens machined from TD nickel bar. The use of miniature torsional pendulum specimens alloived damping measurements to be made on specimens whose axes were parallel to the original bar axis, at 45 deg to the bar axis, and at 90 deg to the bar axis. There was a marked difference in damping with varying specimen orientation, and this was related to the pronounced micro structural anisotropy of this material. Varying the microstructure by cold working plus re crystallization annealing also greatly affected the damping behavior. Recrystallization essentially removed the broad peak found at 400° to 650°C in as-received TD nickel, and in addition greatly lowered the background damping. DlSPERSION hardened metals such as SAP-type alloys (Al + AI2O3) and TD nickel (Ni + 2 pet ThO2) have been developed primarily to improve high temperature strength properties. There have been numerous damping studies on SAP-type alloys,1"9 and one of these6 showed that the damping capacity was greater than that of 99.5 pet pure Al from 25° to 600°C. Several preliminary observations on TD nickel10 and an experimental Ni-ThO2 alloy11 indicated that here, too, the damping capacity was quite high. A high damping capacity in TD nickel, combined with its relatively good high temperature creep strength, could provide an additional benefit for some high temperature structural applications. This work was undertaken to study the internal friction behavior of TD nickel bar over the temperature range 25° to 1100°C. In Ni-ThO2 and Ni-Cr-ThOz alloys, other properties such as steady-state creep rate,12 creep rupture life,12'13 modulus of elasticity,14 and ultimate tensile strength,14 are sensitive to orientation with respect to the primary working direction. Thus, in order to examine anisotropy effects in damping, studies were made on specimens machined with their axes parallel, at 45 deg, and transverse to the original bar axis. MATERIAL DESCRIPTION AND EXPERIMENTAL PROCEDURES The material used in this investigation was from the same £ in. diam TD nickel bar that has been studied previously.13'15 The structure typical of the as-received TD nickel is shown in Fig. 1, and additional details of the structure can be found in Refs. 13 and 15. Elongated grains are parallel to the bar axis and are about 10 to 15 u long and about 1 u in diam. This structure is very stable, since no recrys-tallization or grain growth occurred after annealing for 3 hr at 1300°C.13 The total ThO2 content was 2.3 vol pct and the particles ranged in diameter from 100 to 1000. The average particle diameter was 370Å and the mean planar center-to-center particle spacing was 2340Å. To examine the influence of grain and subgrain structure on damping, a section of TD nickel bar was swaged and drawn at room temperature from 1/2 in. diam bar to 0.040 in. diam wire (99.3 pct re-duction in area). The structure in Fig. 2 resulted after the wire was annealed for 3 hr at 1250°C. The recrystallized grains were much larger than the grains in as-received bar, but still showed considerable elongation in the direction of working. A high

Jan 1, 1970

By S. Nakajima, H. Okazaki

Quantitatiue studies of the deformation texture in drawn tungsten wives were made by the X-vay dif-fractottletetr. Experimental results show that the diffraction Intensities are equal to tilose pvedicted from the (1 10). fiber lexlure but the angxla), spreads of. diffraction peaks in the pole distribution curres are different for different diffraction planes and directions. For this reason a modified (110) fiber lextuve model, in which a kind of anisotropy is assumed, is proposed to explain the results. According to this model the poles lying on a line directing front the (110) to the (110) poles in the (1 10) standard stereograpllic projection should show spreads which are different from those lyitlg on a line directing from the (001) to the (001) poles, which is confirmed by the experiments. The anisolvopy and the spveads of the pole positions are large at the outer part of the wires and decrease gradually lowards the inside of the wire. The possibilily of occurrence of such anisolropy in irrelals with fcc stvuctures is discltssed. THE deformation texture of drawn tungsten wires has been assumed by different investigators to be the simple ( 110) fiber texture.' Recently, however, Leber2,3 has shown that a swaged tungsten rod has a cylindrical texture. It changes gradually to the (110) fiber texture by drawing through dies. However, even after drawing to 0.25 mm in diam, the cylindrical texture can still be found in wires together with the (110) fiber texture. This was deduced from the pole figures obtained from the longitudinal section of these wires. Use was made also of quantitative measurements of the pole distribution curves. Leber stated that the angular spread of the pole distribution curves (henceforward called dispersions) are quite different for (400) 45 deg and (400) 90 deg: the former is always larger than the latter. This inequality is accompanied by deviations of the diffraction intensities from the theoretical values for the ( 110) fiber texture. Bhandary and cullity4 have reported similar results on iron wire and explained them by assuming a cylindrical texture. Both Leber3 and Bhandary4 used only the results of the (400) reflection for the determination of the dispersion. The pole figures found by Leber3 and by Rieck5 are largely different. The model given by Leber to explain the effects is in the authors' opinion in some respects unsatisfactory, especially if one looks at other than the (400) reflections. Intensities and dispersions of diffraction peaks are conclusive factors for the determination of the fine structure in wire textures. For this reason we studied them extensively to come to a model which is more suitable to fit the facts. In the following, after giving the experimental set-up, we report about measurements of X-ray diffraction on drawn tungsten wires. Different models to describe the experimental results will be discussed. EXPERIMENTAL GO-SiO2-A12O3 doped tungsten wires drawn to 0.18 mm in diam were used for the measurements. The wires were chemically etched to various diameters down to 0.03 mm. Measurements were carried out for the different wires in order to determine the dependence of the texture on the radius. The wires were cut to pieces of 10 mm length and fixed with paste closely against each other on a flat, polished glass plate. Parallelism of the wires with the surface of the glass plate should be adequate. For the diffraction studies three different X-ray sources were applied, respectively, giving the CuK,, FeK,, and FeKp emission. The measurements were carried out with a diffrac-tometer with a GM counter. The latter was fixed to a certain diffraction angle 20hkl and the diffraction intensity was recorded as a function of the angle of rotation of the specimen around the axis, lying in the specimen surface and perpendicular to the wire axis, as shown in Fig. 1. Measurements were also done with the detector at angles slightly deviating from the diffraction maxima The measured intensities in this case were taken to be equal to the background level. The deviations were chosen as small as possible but large enough to eliminate the influence of the diffraction maxima. The useful range of the rotation angle x of the specimen is generally limited by the wavelength of the X-rays. We have: where and cp is the angle between the wire axis and the normal of the diffraction plane. Intensity measurements were made to find the necessary corrections for counting loss of the GM counter and for distortion resulting from such effects as absorption of X-rays and from inclination of the reflection plane under study with respect to the surface of the specimen. The counting loss was esti-

Jan 1, 1968

By Robert E. Green, Kenneth Reifsnider

Several experiments have been performed in order to illustrate the application of a recently developed X-ray image intensifier system to metallurgical investigations. In the present work the system has been used to study the instantaneous alterations in Laue transmission X-ray diffraction patterns during tensile deformation of aluminum single crystals. Expem'mental results are presented which demonstrate the capability of the system for crystal orientation, for following orientation changes due to lattice rotation during tensile deformation, and for showing changes in the homogeneity of the lattice planes along the specimen length as a function of strain rate. RECENTLY, a new X-ray system has been developed which incorporates a cascaded image intensifier and permits direct viewing and recording of X-ray diffraction patterns produced on a fluorescent screen.1"3 In the present work the results of several experiments are presented which demonstrate the usefulness of this system for metallurgical applications. EXPERIMENTAL PROCEDURE A schematic diagram of the experimental arrangement is shown in Fig. 1. In this system a Machlett AEG-50-S tungsten target X-ray tube, normally operated at 50 kv and 40 ma, serves as the X-ray source. The X-ray tube is placed in direct contact with a 10-in.-long collimator, which transforms the X-ray beam from one with a circular cross section to one with a rectangular cross section 3 in. high and 1/6in. wide. By blocking off all but a small portion of the rectangular slit, it is possible to work with the more conventional "pinhole" collimated X-ray beam commonly used for obtaining Laue diffraction patterns. In the present work the test specimens were 99.99+ pct aluminum single crystal wires & in. in diam and 3 in. long. For the deformation tests the wire crystals were mounted in a special set of grips in a table model Instron machine so that diffraction patterns could be recorded during specimen deformation. For the orientation tests the wire crystals were mounted in a rotating goniometer so that diffraction patterns could be recorded during specimen rotation. At a distance of 3 cm from the specimen axis, a 6 in. diam DuPont CB-2 fluorescent screen is positioned to transform the X-ray image to a visible one. A Super Farron f/0.87 72 mm coupling lens, corrected for 4 to 1 demagnification, transmits the visible image to the image tube. The image intensifier used is a three-stage magnetically focused RCA type C70021A with an S-20 input photocathode and a P-20 output phosphor. The tube has unity magnification and useful input and output screen diameters of 1.5 in. The image on the output phosphor is of sufficient intensity to be viewed directly, to be recorded cine-matographically, or to be displayed by vidicon pick-up on a television monitor. The recording device most commonly used is a 16 mm Bolex motion picture camera fitted with a Canon f/0.95, 50 mm lens. The overall gain of the system is 16,000 for direct viewing and 2240 for recording on 16 mm movie film. The resolution of the system is limited to 1 line pair per mm which is approximately that of the fluorescent screen. This system has been used for cine recording of transmission Laue X-ray diffraction patterns with exposure times as short as 1/220 sec and for vidicon television pick-up and display at a scan time of 1/30 sec. Quantitative information may be obtained from each frame of the movie film, by either stopping the vertical slit down to a point source in order to obtain a conventional Laue photograph or else by retaining the linear beam and introducing fiducial marks as described in a previous paper.4 In either case, each frame may be enlarged to appropriate size for analysis by either using a photographic enlarger and making prints of the desired frames, or, more conveniently, by using a microfilm reader. EXPERIMENTAL RESULTS The first series of photographs which are presented in Fig. 2 serves to demonstrate the usefulness of the system for crystallographic orientation determination. This series of prints, made from enlargements of a 16 mm movie film, shows the dynamic Laue transmission patterns produced by an aluminum single crystal wire which was rotating about the wire axis when the patterns were recorded. The movie films were taken at 16 frames per sec and the crystal was rotated at a rate of 15 rpm.

Jan 1, 1970