Search Documents

By Walter Showak

The published phase diagrams for the copper-zirconium system1,2 indicate that the solid solubility of zirconium in copper is not accurately known. Studies made on relatively impure alloys by Pogodin, Shumova, and Kugucheva3 yielded a maximum solubility value of 1 wt pct Zr at the eutectic temperature. Allibone and sykes5 reported that an as-cast 0.2 wt pct Zr alloy is single phase at room temperature. Limited results obtained by Raub and Enge14 indicated that zirconium solubility in copper is less than 0.13 wt pct Zr at 940°C. Tn 1960, on the basis of a microstructural examination of several copper-rich Cu-Zr alloys, saarivirta6 placed the maximum solubility of zirconium in copper at 0.15 wt pct at the eutectic temperature, 980°C. The present note describes results obtained during a re-investigation of the Cu-Zr system for the purpose of accurately establishing the solidus and solvus curves and the eutectic temperature in copper-rich alloys. High-purity copper (99.99 pet) and zirconium (99.64 pet) consolidated reactor grade sponge were used to prepare several alloys, containing up to 2 wt pct Zr, by induction melting in graphite crucibles in vacuum and chill casting into a split steel mold. The melting procedure consisted of first melting the copper charge and then adding the bulk zirconium wrapped in pure copper foil. Chemical analyses were made of both the cold-rolled alloy ingots after homogenization at 925°C for 450 hr in evacuated quartz capsules and of small specimens which had been used in the phase diagram studies. 'The carbon content of each alloy was also determined and was found to be less than 0.001 wt pct in every case. Metallographic and electrical resistivity measurements were used as the primary methods for this investigation, although some thermal analysis studies were also performed. Heat treatments of all the alloys were carried out with the specimens wrapped in molybdenum or alloy foil (of the same composition as the specimen) and sealed in quartz tubes either in vacuum or under a purified helium atmosphere. Following high-temperature anneals for long periods of time, slight depletion of zirconium from the specimen surface was observed. Therefore, careful preparation of samples for microscopic examination and chemical analysis of the samples themselves was necessary to check the composition of samples used in determining phase boundaries. Points on the solvus curve were determined on quenched specimens by both isothermal reaction after solution heat treatment at 950°C for 8 hr and by isothermal annealing of alloy specimens at successively higher temperatures for times ranging from 24 to 500 hr. Liquation studies for positioning of the solidus and eutectic temperatures were performed by holding a pre-

Jan 1, 1962

By G. L. Kehl, Emilo Jaraiz F., J. S. Brett

The transformation of eutectoid beryllium bronze has been quantitatively investigated at 550° and 592°C, the temperature region where the products of p decomposition are a fine lamellar eutectoid and a coarse lamellar aggregate which replaces the fine eutectoid with prolonged annealing. Metallographic evidence indicates that the coarse lamellar aggregate forms preferentially in the most densely lamellated regions of the fine eutectoid and favors the hypothesis that the development of the coarse lamellar aggregate in the fine eutectoid is due to the occurence of a cellular segregation reaction. WHEN eutectoid beryllium bronze (Cu-94 pct, Be-6 pct) is isothermally transformed at high temperatures in the and y region after quenching from the fl field, the principal initial decomposition process is G one of growth of approximately spherical nodules composed of a number of lamellar colonies of the a and y phases. After the initial reaction has proceeded substantially or completely, depending on the transformation temperature, a second reaction occurs wherein the fine lamellar eutectoid is replaced by a coarser lamellar aggregate composed of the same oand yphases.' This reaction is not simply a spheroidization of the initial fine eutectoid but the nucleation and growth of a coarser, structurally different, and more stable distribution of the @and yphases. Fig. 1 illustrates the replacement of the initial fine lamellar structure by a coarse lamellar aggregate. The a phase is the dark mottled constituent; the light constituent the y phase. The phase diagram for the copper-rich end of the Cu-Be system2 is shown in Fig. 2. The a phase has the face-centered cubic structure characteristic of copper-rich solid solutions. The B phase is a disordered body-centered cubic structure, while the y phase is body-centered cubic, ordered (CsC1, B2 type). A. viswanathanS investigating Debye patterns of Cu-6 pct Be discovered that a transitory phase appeared on very rapid quenching from the /3 region which was absent when the quenching velocity was moderate. The phase could be assigned a body-centtred cubic structure with a lattice parameter of 2.876. Tempering at 100°C for 2 hr after quenching resulted in complete disappearance of the phase. The work of Fillnow and Mack' is the only previously published study of the isothermal transformation of eutectoid beryllium bronze. Their study elucidated the nature of decomposition at various subcritical temperatures in an exploratory fashion. The purpose of the research reported in this paper was principally to obtain quantitative information on the isothermal decomposition of the fl phase and to clarify the relationships existing between the fine lamellar eutectoid and the coarse lamellar aggregate. EXPERIMENTAL PROCEDURE The material used in this investigation was an almost eutectoid Cu-Be alloy bar furnished by D.J. Mack. The alloy had been melted under a protective carbon cover and centrigugally cast into a graphite mold preheated to 490 "C. Segregation was minimized by violent agitation during melting and pouring. The analysis of the casting was 93.85 pct Cu, 5.60 pet Be with traces of Si, Mg, Mn, Co, and Al. To determine the minimum soaking time necessary to insure specimen homogeneity, a number of specimens were held in the P region at 788OC for times fron 1 min to 12 hr and isothermally transformed at 550°C. Specimens betatized less than 12 min exhibited partial transformation at times shorter

Jan 1, 1961

By W. T. Turrall, M. J. Cook

A discussion of modern developments in beneficiation of fine sizes of anthracite, this paper includes a description of the plant flowsheet, an analysis of operating results, and a summary of fundamentals of mineral separation relative to plant operation. DURING the past several years Lehigh Naviga-tion Coal Co. has installed equipment at Tamaqua and Lansford collieries for cleaning and sizing No. 4 buckwheat —3/32 + 3/64 in. and for recovering and cleaning flotation coal —20 + 200 mesh at Tamaqua colliery. Papers describing some of these installations have been presented to AIME. At Coaldale colliery, however, methods used to clean fine coal were inadequate and inefficient. Management decided upon a thorough investigation of all existing processes before building a plant to treat the combined three sizes mentioned. Investigation, carried out on company property and at other plants, entailed a study of hydrotators, hydroclassifiers, tables, spirals, flotation machines, methods of screening, and methods of dewatering. On the basis of this investigation a flowsheet was designed which necessarily excluded many processes in use, and the writers wish to emphasize that no criticism is implied by omission of processes or machines. A determining factor in selection of many machines was the policy of standardizing equipment wherever possible. Flowsheet and Operational Data The first principle to be considered in designing of any plant is efficiency of cleaning as related to laws of classification. Beneficiation of coal may be described as separation of two materials having different specific gravities. Although there is an inherent ash content even in the purest coal which slightly affects its specific gravity, it is recognized that many particles are true middlings. The percentage of these particles allowable in the final product depends upon the ultimate ash, or specifications of the consumer. Richards in his study of free settling and hindered settling classification' determined that particles of equal size and different specific gravities had unequal settling velocities. He also determined a definite size relationship for equal settling velocities with free settling and hindered settling conditions. Considering the design of machines used to clean No. 4 and No. 5 buckwheat, it may be assumed that both free settling and hindered settling conditions exist and that ratio of size for practical operations is between the established values. The essential factor is that the more efficiently and closely sized the feed is maintained, the more nearly perfect the resulting separation. Flowsheet design was governed primarily by factors related to the 1200 to 1500 tons per hr feed to the main plant. It should be stressed that because of the many sources of supply from mine and stripping, the physical characteristics of this feed varied considerably. The most significant influence was varying percentage of fines, necessitating that all machines be capable of operating under maximum peak load during periods of surge. Since cleaning practice is a wet process, about 9000 gal per min containing 14 to 15 pct solids, or 350 tons per hr, must be treated. This slurry contained all the fines, or —3/32 in., but also percentages of oversize, up to 1 % in., dependent on spills or breaks in screen jackets, a not uncommon occurrence in preparation plant practice. The flowsheet developed is shown in Fig. 1. Circled numbers represent points of sampling. Table I gives operational data including size, ash by size, composite ash, rate of flow in gallons per minute, percent solids dry weight, and average tons of solids per hour. It should be noted that these results are subject to human error in sampling practice. Detailed information reported is a representative evaluation of plant operation.

Jan 1, 1954

By E. P. Klier

THE work of Klier and Lyman1 on the bainite reaction has led to the full description of this reaction for medium-carbon low-alloy steels. Certain experimental data reported by Klier and Lyman appear, however, to be improbable of obtaining in very high-carbon steels. The study herein reported consists of an analysis of the transformation characteristics of a 3 per cent chromium, 1 per cent carbon steel by means of X-ray and metallographic methods. From the results obtained it is concluded that the bainite reaction in this steel is more complicated than that reported by Klier and Lyman for the low-carbon low-alloy steels. However, the mechanism of bainite formation in this steel appears to be essentially the same as proposed for the low-carbon low-alloy steels with the modification that the first volumes to transform are carbon-rich rather than carbon-poor. EXPERIMENTAL PROCEDURE The analysis of the steel studied was: Cr, 2.89; C, 1.02; Mn, 0.33; Si, 0.35; S, 0.012; P, 0.020. The stock was received from the Carpenter Steel Co. in rolled bars. Specimen Preparation Specimens were austenitized at 1200°C. (2192°F.) for 25 min. in purified nitrogen. The resultant A.S.T.M. austenite grain size was 0-1. Isothermal transformation was allowed by quenching the specimens into liquid metal baths controlled to ±5°C. at 540°C. (1004°°F.) and above, and to ±2°C. at 490°C. (914°°F.) and below. Following the desired degree of transformation all specimens were water quenched. Metallographic Examination Specimens 1/4 in. round by 1/4 in. were used for metallographic examination. Etchants used were Vilella's reagent (1 gram picric acid, 10 ml. hydrochloric acid to make l00 ml. ethyl alcohol solution) and alkaline sodium picrate (electrolytic). Vilella's reagent was effective in revealing all microconstituents, while the alkaline sodium picrate developed the carbon-rich structures or carbides only. X-ray Examination Two X-ray techniques were used-the Debye-Scherrer method and a back-reflection method. The small specimens necessary for the Debye-Scherrer method were austenitized and then allowed to transform, or were cut from the larger metallographic specimens. The metallographic specimens were used for the back-reflection X-ray analysis. When it was desirable to determine the structure of the carbide present, sliver specimens were electrolytically etched to develop a carbide coating, then were exposed in the cameras. This technique was frequently necessary to allow positive identification of the carbide.

Jan 1, 1945

By E. P. Klier

The work of Klier and Lyman1 on the bainite reaction has led to the full description of this reaction for medium-carbon low-alloy steels. Certain experimental data reported by Klier and Lyman appear, however, to be improbable of obtaining in very high-carbon steels. The study herein reported consists of an analysis of the transformation characteristics of a 3 per cent chromium, I per cent carbon steel by means of X-ray and metallographic methods. From the results obtained it is concluded that the bainite reaction in this steel is more complicated than that reported by Klier and Lyman for the low-carbon low-alloy steels. Henever, the mechanism of bainite formation in this steel appears to be essentially the same as proposed for the low-carbon low-alloy steels with the modification that the first volumes to transform are carbon-rich rather than carbon-poor. Experimental Procedure The analysis of the steel studied was: Cr, 2.89; C, 1.02; Mn, 0.33; Si, o.35; S, 0.012; P, 0.020. The stock was received from the Carpenter Steel Co. in rolled bars. Specimen Preparation Specimens were austenitized at 1200°C. (2192°F.) for 25 min. in purified nitrogen. The resultant A.S.T.M. austenite grain size was 0-1. Isothermal transformation was allowed by quenching the specimens into liquid metal baths controlled to 5°C. at 540°C. (1004°F.) and above, and to 2°C. at 490°C. (914°f.) and below. Following the desired degree of transformation all specimens were water quenched. Metallographic Examination Specimens 1/4 in. round by 1/4 in. were used for nietallographic examination. Etch-ants used were Vilella's reagent (I gram picric acid, 10 ml. hydrochloric acid to make 100 ml. ethyl alcohol solution) and alkalinc sodium picratc (electrolytic). Vilella's reagent was effective in revealing all microconstitucnts, while the alkaline sodium picrate developed the carbon-rich structures or carbides only. X-ray Examination Two X-ray techniques were used—the Debye-Scherrer method and a back-reflection method. 'The small specimens necessary for the Debye-Scherrer method were austenitized and then allowed to transform, or were cut from the larger metallographic specimens. The metallographic specimens were used for the back-reflection X-ray analysis. When it was desirable to determine the structure of the carbide present, sliver specimens were electrolytically etched to develop a carbide coating, then were exposed in the cameras. This technique was frequently necessary to allow positive identification of the carbide.

Jan 1, 1945

By M. Kaufman, D. Rosenthal

IT would be of great importance to our understanding of the phenomena of fracture in metals if a unique relationship could be established between stress and some easily measurable parameter of deformation up to the fracture. It is known that no such relationshir, has been found when the parameter was the mechanically measured strain,' the major part of which is plastic. The present investigation was initiated to determine, among other things, if the X-ray or lattice strain" might be a • For the definition of lattice strain see ref. 2. more suitable parameter. To this end, annealed stress free*' specimens of 61s aluminum alloy were ** Freedom of stress in this particular case means absence of those stresses which can be checked by the technique employed. tested at room temperature and liquid nitrogen temperature (—195OC), by first maintaining the same temperature from the beginning until the end of the test, and then with crossovers from one temperature to the other. Three major factors had to be taken into consideration in designing the specimens and testing equipment. The test setup must allow X-ray pictures to be taken while the specimen is under load (for as much as 2 hr at a given load). Provision must be made for maintaining the test specimen at the temperature of liquid nitrogen as well as at room temperature. In addition, the specimen must be able to rotate to allow the X,ray beam to take in as large a sample of grains as possible, to maintain centering, and to correct for effects of large grains. The final design of the specimen and equipment is shown in Figs. 1 and 2. The specimen and grips are hollow, enabling liquid nitrogen to be poured in through a funnel-container arrangement while the specimen is rotating. The diameter of the specimens at the 2 in. gage section is 5/16 in. with a 3/16 in. diameter hole through the center. A small pilot valve in the lower grip allows a very small stream of liquid nitrogen to escape, thus assuring circulation of the liquid at all times. A low temperature silicone grease-tissue paper packing is used to seal all joints. The specimen is held in the grips by a pin. Spherical socket joints at top and bottom are used to allow for proper alignment. The grips are connected to the thrust bearings by means of plastic couplings to decrease the heat flow. Rotation is accomplished by means of a motor which drives a plastic gear (integral with the lower coupling) through a semiuniversal joint to allow for deforma- tion of the specimen. The torque applied to the specimen is very small. The maximum stress caused by this torque at the highest loads reached was found to be less than 200 psi, The whole unit was mounted in a 10,000 Ib testing machine. An insulation cage was placed around the specimen to cut down air circulation, and consequent frosting of the specimen, and also to reduce radiation and convection heat losses. A narrow window, covered on both sides with a thin plastic materiai allows the X-ray beam to reach the specimen. Thermocouples placed just outside the pilot hole at the lower grip, in the bottom of the funnel container and near the top of the funnel container permitted checks of the

Jan 1, 1955

By B. D. Smith, K. H. Coats

Experiments in which calcium chloride displaced sodium chloride from four cores showed the extent of asymmetry in the resulting effluent concentration profiles. These results provided a check on how validly the mixing process is modeled by a differential (i.e., not finite-stage) capacitance mathematical model. The effluent concentration profile from two consolidated cores exhibited considerable asymmetry, while two unconsolidated cores yielded nearly symmetrical profiles. All runs resulted in breakthrough of the 50 per cent concentration significantly before one pore volume was injected. In addition, velocity appreciably affected the effluent concentration profile from a Torpedo sandstone core. The differential capacitance model matched the data significantly better than a simple diffusion model. The capacitance model allows determination of the amount of dead-end pore space in a porous matrix and the effect of velocity on the rate of diffusion into this space. An experimental program yielding insight into the physical validity of the capacitance effect is described. INTRODUCTION Axial dispersion — the mixing accompanying the flow of miscible fluids through porous media — has been the subject of many relativeiy recent studiesl-13 and a comprehensive review of the topic has been given by Perkins and Johnston.14 This dispersion is of practical interest in studies of the miscible displacement process, fixed-bed chemical reactors, and the adsorption of solutes from a flowing stream onto the surface of a porous medium. In the latter case, the effect of dispersion must be considered when adsorption parameters are determined from the nature of concentration profiles. In general, early studies of dispersion assumed applicability of a simple diffusion equation and were concerned with correlation of the experimentallv determined "effective" diffusion coefficient with system properties over a large range of the latter. Recent have been concerned with the deviations between the asymmetrical effluent concentration profiles observed and the symmetrical ones predicted by the diffusion model. In the present study, effluent concentration profiles were obtained from consolidated and unconsolidated cores. These profiles were compared with those predicted by a differential (i.e., not finite-stage) capacitance model. Solutions to the simple diffusion model, for three sets of boundary conditions, were compared with one another and with the experimental profiles. SUMMARY OF PREVIOUS WORK The reader is referred to Perkins and johnston14 for an extensive review of studies of dispersion in porous media. Many investigators have employed the simple diffusion model characterized by Eq. 1 below: The dispersion coefficient D for unconsolidated systems is correlated by u is interstitial velocity and dp is particle diameter. Since heterogeneity of the sand pack affects the mixing, this equation is also expressed as where a is proportional to the degree of heterogeneity and is about 3.5 for random packs of unconsolidated sand.l4 Eq. 3 holds for 2 For a Do homogeneous (regular) type of packing, should be 1 or less.6 Aris and Amundson6 and Carberry and Bretton consider o to be the number of particle lengths per mixing cell in the finite-stage model. Data from consolidated cores indicate dp to be about 0.36 cm for outcrop rocks, Torpedo sandstone having a reported value of 0.17 cm.15 For v /Do less than about 2, the effect of molecular diffusion must be considered and the total dispersion coeffi-

Jan 1, 1965

By C. S. Barrett, P. Coheur

ANNEALING twins are common in the microstructure of copper that has been rolled and recrystallized. In such samples it follows that a twin relationship should exist between components of the recrystallization texture,1 and several examples of this have been reported. For example, twin relationships have been found in recrystallized electrolytic copper sheet, as indicated in Fig. I, from a paper by Coheur and Lejeune.2 In this pole figure the cube texture (100) [001] is indicated by the hollow squares in the lower half of the figure (the pole figure for 200 reflections) and in the upper, (111), part of the figure. The texture contains, in addition to this orientation, the first-order twins of it, shown in the figure by the filled triangles. This orientation relation has been suggested by others also, under certain annealing conditions,3,4 although pole figures have not been published to confirm it. Some orientations in recrystallized sheets are identical with their twins, because of the symmetry elements of the texture this is true, for example, with the (113) [211] texture so commonly reported for brass-hence it appears impossible in such samples to decide whether the twin relationships result from twinning or merely from the symmetry of the deformation process. The present investigation of a commercial copper strip seems to yield an example in which annealing twins account unambiguously for the principal orientations present. It proves to be a case, also, for which the recrystallization texture cannot be viewed as derived from the deformation texture by a first or second-order twinning mechanism . MATERIALS AND METHODS The samples investigated were of secondary copper (melted in Belgium) to which 0.19 per cent iron had been added to raise the recrystallization temperature. How much the orientation characteristics of this metal can be ascribed to the iron content and how much to other impurities or to melting and pouring practice has not been investigated.* The rolling was done in one direction only, on a mill with rolls of about 20-cm diameter. A strip 10 cm wide was reduced from 5 mm thickness to 0.05 mm by several cold passes at commercial speeds. The samples cut from this 99 per cent reduced strip were X-rayed throughout their entire thickness. A pole figure made soon after rolling and annealing was identical, within experimental error, with one that was made when a two-year interval occurred between rolling and annealing. X-ray patterns were made on a cameral that traversed

Jan 1, 1946

By Charles W. Chesterman

Perlite is a glassy volcanic rock which will, upon rapid controlled heating, expand or "pop" into a frothy material of low bulk density, valued as a lightweight aggregate. The term perlite also is applied to the expanded product. The chemical composition of perlite ranges from that of rhyolite to that of andesite; the water content ranges from 2 to 5%. Most perlite is pale gray, but some is black, brown, or even green. Inclusions in perlite are common and include phenocrysts of quartz, feldspar, biotite, and hornblende, and miscellaneous rock fragments. Occurrences of perlite are restricted to areas of Tertiary and Quaternary volcanic rocks. Perlite occurs as flows associated with thick accumulations of pyroclastic debris and other flow rocks, as dikes, sills, domes, and as selvages of intrusive bodies of volcanic rock. Individual flows of perlite range in thickness from a few feet to as much as 100 ft and commonly cover several square miles. Dikes and sills of perlite generally are small, but domes generally are substantial in size and may be as much as several miles in diameter. Most perlite deposits are large enough and topographically situated so as to lend themselves to low-cost open pit mining methods. Conventional equipment is employed in the mining of perlite. Although milling procedures may appear to be simple, care is exercised in order to produce a carefully sized product and to minimize the production of excessive quantities of fine materials, which have limited use and are considered as waste. Perlite is processed, or "popped," in one of two basic types of furnaces: horizontal rotary or vertical stationary. Both types of furnaces include product collection and dust control systems. Many commercial deposits of perlite are known to occur throughout the world, and although no exact estimate of reserves is available, there appears to be an adequate supply to meet current and future worldwide requirements. End Uses The uses of expanded perlite are many and varied and are based primarily upon its physical and chemical properties. Because of its (1) low bulk density, which generally ranges between 2 and 20 lb per cu ft; (2) low thermal conductivity "K" factor (Btu per hr per sq ft per OF per in, of thickness), which ranges between 0.267 for loosely packed perlite (bulk density of 4.48 lb per cu ft) to 1.25 for perlite gypsum plaster; (3) high resistance to fire; and (4) low sound transmission, expanded perlite is used to a great advantage as aggregate and insulating material in the construction industry. Early uses of perlite were related exclusively to the construction industry, which now consumes about 60% of the domestic production. The primary use of perlite now is as aggregate in insulation boards. Other uses of perlite in 1971 were as aggregate for plaster, horticultural aggregate, low-temperature insulation (cryogenics), and concrete. Because of its low thermal conductivity ("K" factor), high adsorption of sound, low bulk density, and fire resistance, perlite aggregate plasters hold many advantages over conventional plaster. Perlite aggregate plaster lends itself to machine applications, dries quickly, and has relatively high elasticity which reduces cracking after drying. These same features make perlite useful as aggregate in portland cement concrete and asphalt concrete for construction wherever weight reduction, insulation, and acoustics are of prime importance. Perlite-portland cement concrete offers up to 20 times more thermal insulation than conventional concrete, and because of this it finds wide application in roof decks and floor fill in multistory buildings, in

Jan 1, 1975

By M. Schussler, J. S. Brunhouse

Arc-melted and electron-beam melted tantalum in the cold-worked and the recrystallized conditions showed high strength, good tensile ductility, and excellent notch toughness down to 321°F. Arc-melted material, containing moderate amounts of interstitials, possessed better short-time strength than higher purity electron-beam melted material up to 2000°F. Cold-working substantially strengthened arc-melted tantalum, whereas electron-beam melted material exhibited a low work-hardening rate and possessed better formability characteristics. With identical compositions and microstructures, the mechanical properties of melted tantalum and uacuum-sintered tantalum should be similar. TANTALUM metal usage is increasing rapidly in a number of applications. The outstanding chemical corrosion resistance of tantalum accounts for its applications in chemical processing equipment for severe service conditions and for surgical uses in the medical field. The largest present requirements for tantalum are in the electronics industry, where its special properties are useful in capacitors. The high melting point (5425°F) and inherent ductility of tantalum also suggest that tantalum and tantalum-base alloys might offer an excellent combination of high strength at very high temperatures and good fabri-cability. Pure tantalum has been used in significant amounts in parts requiring high-temperature strength, such as heating elements, reflectors, and heat shields in high-vacuum high-temperature furnaces and in electronic tubes. A few very promising tantalum-base alloys have been developed and are being investigated extensively. The possibilities for tantalum as a high-temperature structural material, either unalloyed or alloyed, will become better defined when more extensive mechanical property data are known. pughl measured the tensile properties of vacuum-sintered tantalum in sheet form for the temperature range of 78" to 1500°K (-321' to 2240°F), and Bechtold reported data obtained at low temperatures.' Drennen3 determined creep and stress-rupture properties of both vacuum-sintered and arc-melted tantalum sheet at 1200 °F. Some additional data on the mechanical properties of tantalum at temperatures up to 5000 °F have been summarized elsewhere.4'5 It is probable that large structural shapes of tantalum, either unalloyed or alloyed, can most readily be produced from ingots prepared by melting. Consequently, the present investigation was undertaken to determine more extensive short-time mechanical properties of tantalum metal consolidated by melting. EXPERIMENTAL PROCEDURE Melting and Fabrication—Two tantalum ingots were utilized in this study to obtain information on the effect of interstitial elements on mechanical properties. Both ingots were melted from Union Carbide Metals Co. tantalum dendrites.

Jan 1, 1961

By -1ng. B. Stampa

Introduction The author investigates the technology available for mine flow reversibility by reversing the operation of the main fans. Air bypassing, reversed sense of impeller rotation, and blade angle overturning are indentified as the most important means of achieving the flow reversibility. The axial flow fan is studied in some detail and the important variables of fan capacity, pressure, and efficiency are compared. Although some references to rotor velocity vectors are made (Fig. 1) the subject is not presented in detail in order to stay within the paper's intent. Background Where applicable, the requirements of mine air reversibility are an important part of the overall mining operation and should be given proper attention during mine ventilation design. The need for preventing mine fires in intake shafts is the reason that, for a long time, it has been a requirement in the Eastern European countries to have the feature of flow reversibility built into all main mine ventilators. In West German coal mines, this requirement does not apply since higher priority is given to safety precautions. Some metal and mineral mines in the United States are required to have ventilation currents readily reversible in order to fight underground fires as stipulated by the Title 30, Mineral Resources, and by the mining laws of some states. From an equipment performance standpoint, assuming the validity of other flow technical data, the question of the ventilator flow reversibility is of ten related to the actual scenario of the begining of an emergency. Most of the time, the system operates within half of the design capacity only and assuming that the equivalent mine orifice is stable only a quarter of the design pressure must be produced by the fan in any event. For such an operating point, the effective gradient and energy losses can be disregarded since fire emergencies usually last for only a short period of time. Equipment Comparison Fig. 2 depicts a ventilation arrangement wherein the flow can be reversed through changing the functional position of the dampers (slideplate or blade type). Both axial or radial fans can be applied in this case. For the mine exhaust operation, slide plates (guillotines) I and I11 are opened while plates I1 and IV are closed. The flow thus encounters two reroutings, which due to the reverse ventilation flow cannot be equipped with proper sheet metal deflectors, and therefore large pressure losses result during the air reroute operation. When the intake operation is considered, the dampers I and I11 are closed and the pair I1 and IV is opened. For this arrangement, almost the same flow conditions exist as for the foregoing exhaust mode; however, one additional corner must be applied. Even if a highly efficient ventilator is used in one of the previously described systems, the additional pressure losses resulting from air rerouting plus those encountered between the planes "0" and "00" significantly affect the overall energy requirements. Illustrated in Table 1 are the relative component losses of even flows for evaluation of various detour arrangements. From the aerodynamics standpoint, when these components are being designed, serious consideration must be given to the individual levels of the pressure loss coefficient, 5. Should there be an increase in the sum of the loss coefficients due to the particular component selection such that, for example, the net change is 1.2; the resulting pressure to be produced by the fan can be calculated from:

Jan 1, 1981

By W. A. Ver Wiebe

The year 1939 in Kansas, with a production of 57,944,300 bbl. from 19,669 wells, shows a slight recession from the peak of oil production reached the previous year, when slightly over 59,000,000 bbl. of oil was marketed. The previous peak had been reached in 1917 with 45,451,000 bbl. marketed. Another still earlier peak had been reached in 1904, when slightly less than 5,000,000 bbl. was produced and sold. The production of gas probably reached a new peak during 1939 with a total of over 69 billion cubic feet. Between the peak of the year 1908, when over 80 billion cu. ft. was produced, and that of 1939 the production dropped to 16 billion cu. ft., in the year 1921. During the year 1458 wells were drilled. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly 75 per cent (1029) of the total number of wells were completed as commercial oil wells (824 in western and 205 in eastern Kansas). The commercial gas wells completed number 71, of which 24 are in eastern Kansas and 47 in western Kansas. The remaining completions include 154 dry holes in eastern and 204 dry holes in western Kansas. Based on daily potential capacity the new discoveries of the year accounted for a cumulative initial production of 264,000 bbl. in eastern and 1,158,827 bbl. in western Kansas. It is interesting in this connection to note that the number of wells completed in the state rose gradually to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918, when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak of 1937, the low point was reached during 1931 with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a "new" area—whether it should be called a new pool or a long extension of an older pool. In some places this determination cannot be made until more wells are drilled within the area. Therefore, the figures given

Jan 1, 1940

By W. A. Ver Wiebe

The year 1939 in Kansas, with a production of 57,944,300 bbl. from 19,669 wells, shows a slight recession from the peak of oil production reached the previous year, when slightly over 59,000,000 bbl. of oil was marketed. The previous peak had been reached in 1917 with 45,451,000 bbl. marketed. Another still earlier peak had been reached in 1904, when slightly less than 5,000,000 bbl. was produced and sold. The production of gas probably reached a new peak during 1939 with a total of over 69 billion cubic feet. Between the peak of the year 1908, when over 80 billion cu. ft. was produced, and that of 1939 the production dropped to 16 billion cu. ft., in the year 1921. During the year 1458 wells were drilled. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly 75 per cent (1029) of the total number of wells were completed as commercial oil wells (824 in western and 205 in eastern Kansas). The commercial gas wells completed number 71, of which 24 are in eastern Kansas and 47 in western Kansas. The remaining completions include 154 dry holes in eastern and 204 dry holes in western Kansas. Based on daily potential capacity the new discoveries of the year accounted for a cumulative initial production of 264,000 bbl. in eastern and 1,158,827 bbl. in western Kansas. It is interesting in this connection to note that the number of wells completed in the state rose gradually to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918, when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak of 1937, the low point was reached during 1931 with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a "new" area—whether it should be called a new pool or a long extension of an older pool. In some places this determination cannot be made until more wells are drilled within the area. Therefore, the figures given

Jan 1, 1940

By M. E. Wadsworth, I. B. Cutler, R. W. Bartlett

The oxidation kinetics of ZrC was studied between 450" and 580°C in oxygen pressures from 6.5 x 10-to 1 atm using a ther mogravimetric apparatus and sized powder samples. Two parallel rate controlling processes were observed. A surface reaction occurring at the ZrC-ZrO2 phase boundary accounted for most of the oxidation and had an activation enthalpy of 46 kcal per mole. The other process, believed to be diffusion of oxygen into the ZrC lattice partially replacing carbon, had an activation enthalpy of 53 kcal per mole. The enthalpy for chemisorption of O2 on ZrC was determined to be —13 kcal per mole. Water vapor in the presence of oxygen accelerated the surface reaction rate. THERE has been little reporting of formal rate studies or attempts to ascertain the mechanism of oxidation of carbides. MacDonald and Ransley1 studied the oxidation of titanium carbide which has the same structure as zirconium carbide, fcc. They observed an initial increase in rate with increasing temperature followed by a rapid decrease through a rate minimum and a subsequent second increase at higher temperatures. The discontinuity in the rate rise was attributed to a phase change in the oxide which changed the rate determining step from the surface reaction at the carbide-oxide interface to diffusion through the oxide layer. Samsonov and Golybera 2 studied titanium carbide and reported that during the initial period of oxidation a dense film of Tic-TiO was formed followed by the formation of less adhering layers of higher oxides. The purpose of this investigation was to study the kinetics of oxidation of zirconium carbide and to attempt to gain some knowledge of the mechanism by which oxidation occurs. EXPERIMENTAL PROCEDURE Measurement of the weight gain associated with the oxidation of ZrC was used to determine oxidation rates. The principal experimental parameters were surface area, temperature, and oxygen pressure. Although moderately sized crystals of ZrC can be grown by the Van Arkel method, the only commercially available ZrC is a powder. In using powders, the surface area must be controlled either by fabricating the powder into a sintered pellet with a measurable surface area, relatively fixed during oxidation, or by using sized unconsolidated powder and applying appropriate geometric considerations to the shape of the grains to correct for their diminishing surface areas as they oxidize. Both techniques involve some difficulties. pellets of binder-free zirconium carbide can be made by hot pressing, but it is difficult to obtain densities greater than 90 pct of

Jan 1, 1963

By C. S. Barrett, P. Coheur

AXnealing twins are common in the microstructure of copper that has been rolled and recrystallized. In such samples it follows that a twin relationship should exist between components of the re-crystallization texture,' and several examples of this have been reported. For example, twin relationships have been found in recrystallized electrolytic copper sheet, as indicated in Fig. I, from a paper by Coheur and Lejeune.2 In this pole figure the cube texture (100) [001] is indicated by the hollow squares in the lower half of the figure (the pole figure for 200 reflections) and in the upper, (III), part of the figure. The texture contains, in addition to this orientation, the first-order twins of it, shown in the figure by the filled triangles. This orientation relation has been suggested by others also, under certain annealing conditions,3'4 although pole figures have not been published to confirm it. Some orientations in recrystallized sheets are identical with their twins, because of the symmetry elements of the texture— this is true, for example, with the (113) [ZII] texture so commonly reported for brass—hence it appears impossible in such samples to decide whether the twin relationships result from twinning or merely from the symmetry of the deformation process. The present investigation of a commercial copper strip seems to yield an example in which annealing twins account unambiguously for the principal orientations present. It proves to be a case, also, for which the recrystallization texture cannot be viewed as derived from the deformation texture by a first or second-order twinning mechanism. Materials and Methods The samples investigated were of secondary copper (melted in belgium) to which 0.19 per cent iron had been added to raise the recrystallization temperature. How much the orientation characteristics of this metal can be ascribed to the iron content and how much to other impurities or to melting and pouring practice have not been investigated.* The rolling was done in one direction only, on a mill with rolls of about 20-cm diameter. A strip I. cm wide was reduced from 5 mm thickness to 0.05 mm by several cold passes at commercial speeds. The samples cut from this 99 per cent reduced strip were X-rayed throughout their entire thickness. A pole figure made soon after rolling and annealing was identical, within experimental error, with one that was made when a two-year interval occurred between rolling and annealing. X-ray patterns were made on a camera2 that traversed

Jan 1, 1947

By C. S. Barrett, P. Coheur

AXnealing twins are common in the microstructure of copper that has been rolled and recrystallized. In such samples it follows that a twin relationship should exist between components of the re-crystallization texture,' and several examples of this have been reported. For example, twin relationships have been found in recrystallized electrolytic copper sheet, as indicated in Fig. I, from a paper by Coheur and Lejeune.2 In this pole figure the cube texture (100) [001] is indicated by the hollow squares in the lower half of the figure (the pole figure for 200 reflections) and in the upper, (III), part of the figure. The texture contains, in addition to this orientation, the first-order twins of it, shown in the figure by the filled triangles. This orientation relation has been suggested by others also, under certain annealing conditions,3'4 although pole figures have not been published to confirm it. Some orientations in recrystallized sheets are identical with their twins, because of the symmetry elements of the texture— this is true, for example, with the (113) [ZII] texture so commonly reported for brass—hence it appears impossible in such samples to decide whether the twin relationships result from twinning or merely from the symmetry of the deformation process. The present investigation of a commercial copper strip seems to yield an example in which annealing twins account unambiguously for the principal orientations present. It proves to be a case, also, for which the recrystallization texture cannot be viewed as derived from the deformation texture by a first or second-order twinning mechanism. Materials and Methods The samples investigated were of secondary copper (melted in belgium) to which 0.19 per cent iron had been added to raise the recrystallization temperature. How much the orientation characteristics of this metal can be ascribed to the iron content and how much to other impurities or to melting and pouring practice have not been investigated.* The rolling was done in one direction only, on a mill with rolls of about 20-cm diameter. A strip I. cm wide was reduced from 5 mm thickness to 0.05 mm by several cold passes at commercial speeds. The samples cut from this 99 per cent reduced strip were X-rayed throughout their entire thickness. A pole figure made soon after rolling and annealing was identical, within experimental error, with one that was made when a two-year interval occurred between rolling and annealing. X-ray patterns were made on a camera2 that traversed

Jan 1, 1947

By A. A. Collins

OF widespread interest to all lead metal¬lurgists is a dross smelting process that will consistently give mattes and speiss of low lead and high copper contents. It is -a problem that has intrigued operators through the years. In the past few years, with increased amounts of copper and overcrowded metallurgical furnaces, it has been almost imperative to evolve some method. Experience at El Paso has shown that high copper-to-lead ratios can be consistently attained by use of the new soda process.* OLDER METHODS Three older methods; i.e., I. Dross plus siliceous ore and limestone, 2. Dross plus one fourth blast-furnace speiss and siliceous ore, 3. Dross plus sulphides and siliceous ore and scrap iron, do not give consistent results and the products are higher in lead and lower in copper than those produced with the soda process. Any radical changes in the blast-furnace drosses will throw any of these older methods into a tailspin. For almost ten years, El Paso used the third method, with varying results. It was noted that as the arsenic and antimony contents of the dross increased, the speiss and matte steadily increased in lead and decreased in copper. A dross containing four parts of copper to one part of arsenic was considered to be ideal. At times this balance of copper to arsenic was almost impossible to obtain, especially when handling copper Cottrell dusts, which vary so greatly in copper and arsenic. Custom smelters like El Paso, handling a great variety of dusts, concentrates and ores, are apt to have anywhere from 1 to 15 pct copper on charge, with a variable in arsenic of from 0.5 to 2 pct. With such conditions, and drosses varying from 12 to 40 pct copper, an operator using the older dross reverberatory practices would find it just about im¬possible to control the reverberatory operations and to produce a good product low in lead and high in copper. These conditions prevailed at El Paso from the year 1940 to the present. In May 1942 it, was decided to experiment with the soda process. THE SODA PROCESS After considerable work the soda method was finally evolved to the present state. It has never failed to produce a good product even under the most adverse conditions. It might be well to remember that many men of thought in the smelting industry have at one time or other suggested the removal of all copper, arsenic and antimony from the lead blast-furnace charge as an aid to better metallurgy.

Jan 1, 1947

By Phillip B. Bucky, Fred D. Wright

The present known petroleum reserves are limited, and unless important new fields are discovered the Nation will be dependent, in the not too distant future, upon imports or upon synthetic liquid fuels to supplement domestic petroleum supplies. As a national defense measure, it would appear desirable to develop a substitute source of liquid fuels within the borders of the country if new discoveries of petroleum should Prove disappointing. Congress undoubtedly had this in mind when it passed the Synthetic Liquid Fuels Act (78th Congress, approved April 5, 1944). The act directed the Bureau of Mines to construct and operate demonstration plants for producing synthetic liquid fuels from coal and oil shale, and from forestry and agricultural products. As a part of this program, the Bureau of Mines has built a demonstration plant at Anvil Points, near Rifle, Colo., for retorting the oil shale, and has developed a mine to supply the plant with oil shale. At the beginning of mining operations, the physical qualities of the oil shale, which would have a bearing upon the selection of mining methods and practices for exploiting the deposits, were largely unknown. A comprehensive mining-research program has been set up to determine the best methods and practices to follow to obtain the lowest overall practicable mining cost for producing the oil shale on a large scale. Unusually low mining costs will be necessary for shale oil to be produced commercially. Consideration now is being given to exploiting a series of flat-lying beds 70 ft thick by a room-and-pillar method of three benches with the advance heading at the top. This report is one of a series giving the results obtained in research on mining problems, The structure and physical qualities of the oil shale indicate that the 70-ft interval of the oil-shale measure can be safely mined in open stopes; studies indicate that this method would be the most economical one to use.' As labor will be a major item of expense, the largest equipment that could be operated efficiently in the workings would be required to obtain the lowest practicable mining Cost. It Was therefore desirable to know the maximum safe span of unsupported rooms and the size of pillars necessary to support the overburden. This paper describes the work done at the Columbia School of Mines Barodynamic Laboratory in determining the maximum safe unsupported roof spans and the minimum safe pillar dimensions for the oil-shale mine at Rifle, Colo.

Jan 1, 1949

By D. B. Jugle, J. B. Darby, O. J. Kleppa

A systematic study has been made of the kinetics of solution under steady state, dynamic conditions of titanium, vanadium, chromium, iron, cobalt, and nickel in liquid aluminum. It was found that the temperature dependence of the solution rate obeyed an Arrhenius-type rate equation, and that at a given temperature the rate of solution of the various solutes correlates quantitatively with the equilibrium solubility of the solute in liquid aluminum. These results are consistent with a mechanism where the rate-controlling step is the diffusion of solute atoms through a liquid boundary layer. THE present study was initially started in order to explore the feasibility of liquid-metal solution calorimetry for transition metals and alloys. Previous work1 in this field employing liquid tin as a solvent at temperatures in the 500' to 600' range had indicated that the rates of solution of most transition metals in tin are very low. Under such conditions effective solution calorimetry is difficult. The objective of the present investigation was two-fold: a) To obtain, as far as possible, quantitative data on the rates of solution of a series of transition elements in liquid aluminum. b) To explore whether liquid aluminum might be a suitable solvent for liquid-metal calorimetry. In the course of this work a comprehensive set of data was obtained on the steady state rates of solution of transition metals in a common liquid-metal solvent. The results are consistent with the boundary layer model, which assumes that the rate-controlling step consists of diffusion of solute atoms through a viscous liquid layer. EXPERIMENTAL PROCEDURE A vacuum-tight stainless steel vessel was surrounded by a resistance furnace, as shown in Fig. 1. In all experiments the temperature of the liquid solvent was controlled to 2.5' by means of a Micromax controller. A high-vacuum manifold connected to the vessel maintained a vacuum of 1 x 105 mm of Hg or better. The vacuum vessel was equipped with a charging section isolated from the working chamber by a vacuum-tight gate valve. This arrangement allowed the specimen holder to be removed or inserted into the apparatus without removal of the liquid metal bath. The specimen holder was suspended from a closed end stainless steel tube, which also served as the thermocouple protection tube. The portion of the tube that was below the solvent level was surrounded by an alumina protection tube to isolate it from the liquid metal bath. The stainless steel tube was connected through a rotary vacuum seal and a gear train to a fractional horsepower motor. For most experiments the tube was rotated at a constant

Jan 1, 1963

By Pedro Bolsaitis, Paul M. Sullivan

The activities of zinc in liquid Zn-A1 alloys in the temperature range of 1000' to 1160°K were determined by means of the isopiestic technique. The results are in reasonable agreement with the previous values determined by the radioactive tracer dew point method. Slightly negative excess entropies of mixing were found. The measured activities suggest that the a function for these alloys is not a constant, as has frequently been assumed, but is better represented by two straight line segments of different slopes. THE thermodynamic data of Al-Z alloys have been the subject of investigation by many authors. However, in the recent compilation of such data by Hult-gren et al.,5 the conclusion is reached that none of the previous measurements are reliable or consistent with each other. Since then two new sets of measurements have been reported,2, 8 both laying claim to good accuracies, yet showing very significant disagreement in the measured activity coefficients of zinc in Zn-A1 alloys and in the magnitude and sign of the excess entropies of mixing. Information on the thermodynamics of the system is of particular interest for interpreting results of the Bureau of Mines research on refining of zinc by distillation of die cast scrap. The present study was undertaken as an independent check on the recent values obtained from dew point measurements 8 and electromotive force measurements.' The isopiestic method, first introduced by Herasy-menko,' was chosen because it is one of the few thermodynamic techniques which, in principle at least, is carried out under perfect equilibrium conditions. The disadvantage of the method is that data are obtained at various random compositions and temperatures, which makes the interpretation somewhat cumbersome. The random errors arising from temperature gradients and fluctuations appear to be comparable to those of other techniques, as evidenced by the magnitude of the estimated uncertainties in the calculated integral thermodynamic quantities. An advantage of the method is that each run provides a relatively large amount of data; thus, it is less time consuming than those methods where samples of each composition must be measured individually. EXPERIMENTAL PROCEDURE The activities of zinc in liquid Zn-A1 alloys were measured by the isopiestic method which uses the principle of the tendency toward equilibrium of a series of samples at various temperatures under an imposed vapor pressure of the more volatile component (i.e., zinc, in this case). The basic apparatus is shown in Fig. 1. The small graphite crucibles that contained the metal samples were 15 mm ID and 13 mm deep with approximately 3 mm wall thickness. Each crucible was notched at the top and bottom to allow easy passage of vapor from one to another. At the beginning of an experiment each crucible was weighed on an analytical balance. Zinc and aluminum of spectrographic purity (99.999 pct) were then weighed into the crucibles. The amounts of each metal added were such that initial compositions varied above and below equilibrium values. One crucible contained only pure zinc. After weighing, the crucibles were stacked with the pure zinc on the bottom (corresponding to the lowest temperature in the furnace) and richest aluminum alloys at the top. The entire stack of crucibles was then placed in the silica glass container "E" which was then sealed under vacuum. Sixteen to twenty calibrated Chromel-Alumel thermocouples were attached by wire along the length of the silica tube, one or more adjacent to each sample.

Jan 1, 1970