Search Documents

By John W. Bell

IN the introduction to an excellent pamphlet, John Gross1 makes the following statements: Although marked progress has been made along mechanical lines, the theory and conception of underlying principles have not advanced so rapidly. This lack of advance in theory may be attributed to the unfortunate situation resulting from the controversy as to whether the Rittinger or Kick law is applicable to crushing. Many pages of the technical literature are burdened with theoretical discussions in favor of one or the other of these laws, which have tended to cloud rather than to clear the atmosphere. Realizing the situation, the Milling Committee of the American Institute of Mining and Metallurgical Engineers, through its secretary, E. A. Hersam, studied the milling industry and, because of the apparently hopeless lack of agreement in the Kick versus Rittinger dispute (5, 13, 14, 16, 18, 19, 21, 22, 23, 24, 30. 34), concluded that a foundation for the theory of crushing was of primary importance. The numbers in the paragraph quoted refer to papers listed by Mr. Gross in his Bibliography on Crushing and Grinding.1 One is obliged to infer that these papers show "hopeless lack of agreement in the Kick versus Rittinger dispute." No. 22 is a paper by Arthur O. Gates2 and No. 23 is one by the writer.3 Employing the subject matter contained in papers Nos. 22 and 2323 the writer will show that their authors formulated identical conclusions, based solely on experimental evidence. Exactly the same defect in the Stadler hypothesis was described in each of the two papers, although entirely different experimental methods were employed in uncovering it. Both of the authors, independently, formulated the conclusion that Rittinger's was a. true hypothesis and Stadler's false. The evidence in a third paper4 will be employed to prove that Stadler's hypothesis, when examined experimentally, is worthless. STADLER'S HYPOTHESIS WORTHLESS It is the writer's opinion that the evidence available in 1915 and the corroborating evidence in 1916 was amply sufficient to eliminate the need for any further consideration of Stadler's hypothesis. Certainly the evidence produced in 1918 dealt this hypothesis its coup de grace. It follows, therefore, that in the year 1918 there was only one credible hypothesis left-the Rittinger hypothesis. Gates' Opinion What information is available in Mr. Gates' paper?2 His conclusions are not consecutively summarized, none the less they are perfectly clear. On page 876, Gates says, and it is a very significant utterance: But my results show, among other things, that many more of Stadler's energy units are obtained per foot-pound-applied in coarse than in fine crushing. This suggests a doubt as to the correctness of his unit, since one would expect a foot-pound-applied to produce the same number of "energy units," whether the feed and resulting product were coarse or fine. When Rittinger's theory is applied, the number of mesh-tons (my unit of surface produced) is

Jan 1, 1942

The great Bingham Canyon mine and mill complex of Magna, Arthur, and Bonneville had their beginning in a 300 ton per day operation which was commenced by Daniel C. Jackling and his associates in 1904 as the Utah Copper Company. This small plant was quickly expanded to 500 tons per day and eventually Kennecott, the Utah Copper successor, was processing about 45,000 tons per day of ore in each of its mills, Magna and Arthur. Finally, in 1966, the Bonneville crushing and grinding plant was added to produce a slurry of ground ore for flotation concentration at the expanded Magna and Arthur mills. Bonneville is one of the few railroad dump primary gyratory crushing plants constructed in recent years; another which is described in this Monograph is Cuajone in Peru, started in 1976. Two others are the Climax Henderson unit and the Phelps Dodge Tyrone crusher, which has been fed by trucks since it commenced operation. The Bonneville, Henderson, and Cuajone crushers are all located considerable distances from their mines, hence the use of rail haulage. Shovels in the Bingham pit are 8 to 15 yd capacity; and ore is sent to the Bonneville crusher in 100 ton rail cars, where they are dumped, two at a time, by a hydraulically driven rotary dumper. Ahead of the 54 in. by 74 in. Allis-Chalmers gyratory are two grizzlies, each 27 ft 9 in. (8.46 m) long with bar spacings of 4 ½ in. (114 mm) at the feed end and 6 in. (152 mm) at the discharge end. Grizzlies are sloped at 38. Oversize rocks are re- moved from the crusher pocket by an overhead crane, and the crusher produces a nominal 6 in. (152 mm) product. Rail cars are dumped in the direction away from the crusher, and water sprays at the dumper level and in the rock boxes are used for dust suppression. There are two 72 in. by 19 ft (1.83 m by 5. 8 m) apron feeders under the 500 st cr'ushed ore pocket and two more under the grizzly undersize pocket. Feeder speeds are variable up to 72 fpm. Grizzly undersize is dropped to the feeder pocket by three shelves forming a rock ladder attached to the pocket walls. Each pair of apron feeders, one for crushed ore and one for grizzly undersize, discharge to a 72 in. (1. 83 m) picking belt for tramp removal; this belt feeds one of two 54 in. (1.37 m) feeder conveyors which in turn discharge to a 60 in. (1. 52 m) takeaway belt operating at 175-300 fpm (53.3 - 97.4 mpm). Both picking belts are equipped with metal detectors and tramp iron magnets, and a separate 30 in. (760 mm) conveyor is used to remove tramp material.

Jan 1, 1978

The Western World's gold reserves now exceed 23,000 mt (750 million oz), 65% of which exist in South Africa. Although several major mines are reducing production or closing because of depletion of reserves, new mines or expansions of existing mines are coming on-stream which will maintain an annual production of 684 mt (22 million oz) of gold well into the 1990s. These new operations by the South African mining industry represent the largest expansion since the opening of the Witwatersrand gold fields in 1886. Included in three new mines being opened is that of Anglo American Corporation's Elandsrand plant, their fir& new gold venture in South Africa in seventeen years. Current average grade of South African mines is 8.2 g Au per mt (0.24 oz per st); and while the cost of the Elandsrand 135,000 mt (149,000 st) operation, including mine development, was about $314 million, it is estimated that the cost of a comparable operation started today and completed in the mid-1980s would be of the order of $480 million. New mines to exploit low-grade ore bodies are, therefore, likely to be few in number, and further expansion will undoubtedly be in the form of extensions to existkg operations where cash flow can be used to finance development. The authors' first monograph, "Gold and Silver Cyanidation Plant Practice," devoted a section to South African cyanide plant operation; and it is believed that this new volume would not be complete without a description of Elandsrand, South Africa's newest gold plant. The Elandsrand mine is adjacent to Anglo American's Western Deep Levels on the Far West Rand. The decision to go ahead with the development was taken in mid-1974 from the results of exploration drilling carried out over a period of .lo years. Results of 17 bore holes and 68 intersections of the Ventersdorp Contact Reef had indicated a gold-.bearing reef less than one meter thick at a depth of 1,800 to 3,000 meters (5,900 to 9,840 ft). Preliminary studies indicated a mine of 900 km (560 miles) of underground workings would yield 725,000 kg (23. 3 million oz) of gold from 60 million mt (66 million st) of ore to be milled over a period of 34 years. Eventually, when the mine is in full production, the total hoisting capacity will be 300,000 mt per month (331,000 st) for a milling capacity of 225,000 mt per month (248,000 st). The Elandsrand surface facilities have been built on a low range of 0 hills to take maximum advantage of the 10 slope in transporting ore

Jan 1, 1981

By George A. Packard

The shaft of the Raven mine, at Butte, Mont., is an incline 1,700 ft. in length and dipping at various angles. At the top the dip is 70" from the horizontal, but this is gradually flattened until at the 300-ft. level the inclination is only 47. This angle continues to the 1,100-ft. level, below which it curves with a 125-ft. radius to 78". In addition to these variations in dip, the shaft does not lie in the same vertical plane, with the result that the hoisting rope not only rubs at intervals on both the hanging and foot walls, but presses strongly against the west dividers near the collar, while 300 ft. below it runs close to the east end plates. The early operators used no idlers, aid wall plates cut 6 in. deep by the rope resulted. Later operators first attempted to overcome the excessive friction, and the wear of rope and wall plates, by introducing solid cast-iron idlers, 3 in. in diameter. To allow for the travel of the rope from side to side some of these had to be 3 ft. long and were very heavy. Judging from the appearance of the old idlers of this type found at the mine, they often failed to turn in the bearings, which is not surprising when it is considered that they would have to make 1,000 rev. a minute under ordinary hoisting conditions. The next rolls were made of wood, 6 in. in diameter, with an iron band about each end, and a pintle of 1-in. round steel driven in at the ends to serve as a shaft. These wore rapidly, and were soon replaced by rolls made from water pipe, 5 or 6 in. in diameter, cut to the desired length and fitted with a wooden cylinder into which the pintle was driven. Where the idlers were used on the hanging wall of the shaft the original bearing was simply a piece of + by 1 3/2 in. strap iron, 10 in. long, turned up at the end in a circle 11/8 in. in diameter to receive the shaft. A small hole served for oiling, and common black oil was generally used, although filtered oil from engine bearings and compressor bearings was also used. When the rolls were to be placed on the foot wall the bearings were made from two pieces of 1 by 3 in. steel, 6 in. long. A half circle was cut on the flat side of each piece and the two half circles together formed a bearing. Oil holes were provided, and in some cases holes were bored through the two pieces so that they could be screwed or spiked to the wall plates.

Jan 1, 1915

By L. J. Demer, W. W. Walker

AMONG several variables of the indentation hardness test is the effect of loading time on the measured hardness of a material. The most generally recommended duration of loading is 10sec.1-3 Although this short loading duration is undoubtedly satisfactory for harder metals, it is questionable that it is sufficient for very soft metals,4 or for certain plastics.5 The effect of duration of loading on the measured hardness of ionic crystals is largely unknown, although Onitsche and Mitsches found that the indentor (under a very low load) had not yet reached equilibrium after 60 sec in a variety of ionic crystals. To extend further the data of Onitsche and Mitsche, a systematic study was made of the effect of duration of loading for longer periods, up to 50,000 sec, on the 136 deg Dph of synthetic lithium fluoride. For comparison, less extensive tests were made on synthetic magnesium oxide and copper single crystals. The general procedure used was to indent a cleaved and polished (100) face of a lithium fluoride crystal using a Leitz Durimet microhardness tester. In certain cases, the indentor was so oriented as to align the diagonals of the 136 deg diamond pyramid indentation parallel to a (100) edge. In other cases the diagonal of the indentation was aligned at 45 deg to a (100) edge of the crystal. After indenting, the surface tested was etched in the acid etchant recommended by Gilman and Johnston.' This revealed the position of dislocation lines which intersected the surface tested. At these points of emergence were formed the usual sharp, pyramidal etch pits as shown in Fig. 1. The specific procedure used in studying duration of loading was as follows. The surface of the crystal was indented, and the load was left on the indentor for a predetermined time. This duration of loading was varied systematically from 1 to 50,000 sec. After the desired amount of time had elapsed, the indentor was removed from the crystal and the size of the resulting indentation was determined using a micrometer eyepiece. The surface was then etched to reveal the dislocation etch pit pattern around the indentation. Procedures used for lithium fluoride, magnesium oxide, and copper were similar. Preliminary studies revealed that, although an indentation was enlarged by increasing loading time, no corresponding changes occurred in the surface etch pit pattern. Since no evidence of dislocation movement was observed on the surface, it was assumed that the plastic deformation indicated by the indentor sinking into the surface was a result of dislocation movement inside the crystal. This movement was studied bf making a series of surface indentations in a crystal corresponding to various lengths of time, cleaving the crystal vertically through the indentations, etching the freshly

Jan 1, 1964

By George Packard

THE shaft of the Raven. mine, at Butte, Mont., is an incline 1,700 ft. in length and dipping at various angles. At the top the dip is 70° from the horizontal, but this is gradually flattened until at the 300-ft. level the inclination is only 47°. This angle continues to the 1,100-ft. level, below which it, curves with a 125-ft. radius to 78°. In addition to these variations in dip, the shaft does not lie in the same vertical plane, with the result that the hoisting rope not only rubs at intervals on both the hanging- and foot-walls, but presses strongly against the west, dividers near the collar, while 300 ft. below it runs close to the east end plates. The early operators used no idlers, and wall plates cut 6 in. deep y the rope resulted. Later operators first attempted to overcome the excessive friction, and the wear of rope and wall plates, by introducing solid cast-iron idlers, 3 in. in diameter. To allow for the travel of the rope from side to side some of these had to be 3 ft. long and were very heavy. Judging from the appearance of the old idlers of this type found at the mine, they often failed to turn in the bearings, which is not surprising when it is considered that they would have to make 1,000 rev.. a minute under ordinary hoisting conditions. The next rolls were made of wood, 6 in. in diameter, with an iron band about each end, and a pintle of 1-in. round steel driven in at the ends to serve as a shaft. These wore rapidly, and were soon replaced by rolls made from water pipe, 5 or 6 in. in diameter, cut to the desired length and fitted with a wooden cylinder into which the pintle was driven. Where the idlers were used on the hanging-wall of the shaft the original bearing was simply a piece of 2 by 1-1 in. strap iron, 10 in. long, turned up at the end in a circle of 18 in. in diameter to receive the shaft. A small hole served for oiling, and common black oil was generally used, although filtered oil from engine bearings and compressor bearings was also used. When the rolls were to be placed on the foot-wall the bearings were made from two pieces of 1 by 3 in. steel, 6 in. long. A half circle was cut on the flat side of each piece and the two half circles together formed a bearing. Oil holes were provided, and in some cases holes were bored through the two pieces so that they could be screwed or spiked to the wall plates.

Jan 8, 1914

SOME days ago a visiting member from Pittsburgh who is an ardent supporter of the Institute remarked: "There are a lot of men who would be members of the Institute if it weren't so expensive. It is not so much the $15 dues as the $20 initiation fee. This makes quite a hurdle, especially for the younger fellows." A little further conversation developed the fact that the member had never learned of the changes in the By-laws regarding initiation fees and dues made by unanimous vote of the Board of Directors last November. As a great many others doubtless are unaware of these changes, the substance of two of the amendments is here repeated. They provide: (1) That the initiation fee for Junior Members (heretofore ten dollars) he abolished. (2) That the age limit for entrance as a Junior Member be increased from 27 years to 33; provided further, that the period during which the dues of a Junior Member are ten dollars shall be a maximum of six years but in no event shall extend beyond his thirty-third birthday. The Junior Member gets the identical privileges enjoyed by his seniors and he likewise assumes the same obligations with the sole exception of the financial payments. This one exception is justified by the fact that the engineers of more mature years, who are established in the profession, - are able and willing to assume a slightly greater financial burden. In effect, it is a small subsidy for the younger men; but these in turn will later enter the group of those that give instead of receive assistance. The practical result is that an engineer under 27 can obtain every privilege and benefit of membership for six years on the payment of only $10 per year without any initiation fee. A man of thirty can do the same for a period of three years. Incidentally, a candidate applying for membership (either as senior or junior) in the next few months need pay dues for the second half of 1935 only. A Junior Member -can be enrolled with an immediate outlay of only $5. The Institute does not seek-members indiscriminately merely to swell the number. These facts are not presented as a "bargain" offer in any sense. The standards for admission are high and are watched zealously. But it frankly-wants to give qualified men who can benefit from membership every encouragement to apply. Naturally, the Institute does not want lack of accurate information regarding initiation fees and -dues to be a stumbling block to any that are eligible and desirous of enrolling. Members are urged to take it upon themselves to clear up misapprehensions on this point, particularly among younger engineers.-Editorial reprinted from MINING AND METALLURGY, May, 1935.

Jan 1, 1935

By R. I. Garrod, R. A. Coyle

The shapes and positions of X-ray reflections from specimens of copper, steel, and aluminum alloy haue been examined in the elastic and plastic ranges both while the specimen was under stress and in the unloaded condition. For the aluminum alloy the shape was unaltered by the application of stress either within the elastic limit or in the plastic range provided that no additional plastic strain was induced. In copper the broadening accompanying plastic deformation was very slightly reduced when the specimen was unloaded. A similay but more marked elastic component of broadening was also found for steel, but in this case below the yield stress. Line profiles corrected for instrumental and particle-size broadening indicate very large internal stresses in local regions of the plastically deformed metals. The results are discussed in terms of a recent suggestion that the heterogeneous dislocation distribution between the cells and their boundary walls plays a major role in the peak shifts and broadening of the X-ray reflections. STUDIES of the X-ray line profiles from strained polycrystalline aggregates concentrate usually on one or the other of two main parameters: a) the displacement of the peak of the intensity contour from its position for a strain-free aggregate, or b) the shape of the profile. From peak shifts data can be obtained either on the relation in both the elastic and plastic ranges between applied external stress and average lattice strains in a given (hkl) direction, or, alternatively, on the residual lattice strains which are present after a plastically deformed specimen is unloaded.' On the other hand, the shapes of the broadened profiles from cold-worked metals can be analyzed to separate the broadening produced by small particle size and by heterogeneous lattice strains.' In this paper the terms "size broadening" and "strain broadening'' are used in the general sense adopted by warren.' In the past, apart from two early qualitative observation, it has been customary to examine only the movements of the peaks of the profiles while the specimen is actually under load, since the line broadening induced by plastic strain remains after removal of the external stress. Consideration of the implications of existing data of this type suggests, however, that fruitful additional information on a number of fundamental aspects might be gained by careful examination of whether the X-ray line profile is in fact different in the loaded and unloaded states of the specimen. By taking advantage of the sensitivity and convenience of modern diffractometer techniques it is possible to explore with relative ease the magnitude and importance of any elastic effects which may be superimposed upon the well-known permanent changes in profile. The main aim of the work to be described was thus to investigate this point for typical metals and alloys. For this purpose annealed specimens were extended first elastically and then plastically and the positions and shapes of X-ray reflections were recorded. Initially it was anticipated that prime interest would center on observations within the plastic range; it has been found, however, that small changes in profile sometimes occur both before and after the nominal elastic limit of the material is reached. It is shown that the results obtained have important implications in relation to the structural changes and processes associated with deformation. I) EXPERIMENTAL To enable the diffraction lines to be recorded while the specimen was under uniaxial-tensile stress, a small hydraulic testing machine was designed and constructed for direct attachment to the goniometer of a Philips diffractometer. The specimens, which were machined from 1/2-in.-diam rod and had a central rectangular section 3/8 by 1/16 in. over a gage length of 1 in., were held in the machine by split collets mounted in grooves in the cylindrical ends of each specimen. No special precautions were taken to ensure precise axiality of loading. Constant oil pressure was maintained by a lever and weights system and transmitted to the loading rig by flexible pipe. The actual load on the specimen was measured by a load cell in the machine to an accuracy of * 1 pct. To enable smooth X-ray profiles to be obtained the specimen and machine were oscillated continuously during recording through *7-1/2 deg about the normal half-angle position of the goniometer. The three materials chosen for the investigations were high-purity copper as representative of a ductile fcc metal, a low-carbon steel for a bcc metal, and an aluminum alloy as a material in which the proof stress/ultimate strength ratio is high. Details are as follows. a) Copper. 99.999 pct purity. After machining the specimen surface was polished mechanically and

Jan 1, 1964

By R. V. Mrazek, F. E. Block, S. B. Knapp

The mixed homogeneous and heterogeneous kinetics of the thermal decomposition of tungsten hexacarbonyl were studied by employing a batch reactor. The system was such that a sample of tungsten hexacarbonyl could be injected into the preheated reactor, and the progress of the reaction followed by a simple pressure measurement. Both the homogeneous and heterogeneous reactions were found to be first order, and approximate activation energies were determined for each reaction. It is shown that the dis-proportionation of carbon monoxide to give carbon and carbon dioxide cannot be the source of carbon in tungsten deposits prepared by this reaction. The kinetics of the thermal decomposition of tungsten hexacarbonyl have been investigated as part of a continuing study by the U.S. Bureau of Mines on the decomposition of organometallic compounds. Reactions involving the thermal decomposition of metal carbonyls have a potential application in the preparation of pure metals and fine metal powders. Indeed, it was these applications which provided the impetus for much of the early work involving the carbonyls of nickel1 and iron.' The relative lack of study of other metal carbonyls can be traced to the comparative difficulty in synthesizing these compounds. The most common use for tungsten hexacarbonyl has been as an intermediate in vapor-phase plating.7'8 However, attempts to obtain a carbon-free deposit of tungsten by this method have not been successful, and some investigators have taken advantage of the carbon contamination and used this process to form tungsten carbide deposits.lo Other investigators have studied the thermodynamic properties11"14 and molecular structure of tungsten hexacarbonyl. However, very little is known about the kinetics of this thermal decomposition, the mechanisms involved," or the source of carbon in the resulting plate. In contrast, studies have been made of the kinetics of the thermal decomposition of nickel tetracarbonyl, iron pentacarbonyl, and molybdenum hexacarbonyl.'l It has been found that these thermal decompositions occur by a mechanism which is partially heterogeneous in nature. Information available on the equilibrium constants for the decomposition of tungsten hexacarbonyl was used to determine a temperature range, 500" to 560°K, in which the reaction could be expected to be essentially complete. APPARATUS The apparatus used allowed the injection of a sample of tungsten hexacarbonyl into a preheated batch reactor and the use of a simple pressure measurement to follow the progress of the reaction in the sealed reactor. The pressure was sensed by means of a pressure transducer (Consolidated Electrodynamics Corp., 0.3 pct)* capable of operating at the *Reference to specific products is made to facilitate understanding and does not imply endorsement of such brands by the Bureau of Mines._______ reaction temperature. This type of sensing element was chosen to avoid the problem of condensation of the sublimed carbonyl in the capillary tubing leading to any type of remote pressure-sensing device. stirring was provided by rotating the entire apparatus. Glass beads placed in the reactor provided a pulsating agitation. To minimize thermal gradients in the reactor walls, the reactor was constructed of aluminum. The support tube which held the reactor in the furnace was thin-walled stainless steel to minimize heat conduction out of the reactor. As a result of these measures, a nearly uniform temperature (°C) was maintained throughout the reactor. Fig. 1 is a schematic diagram of the apparatus. The small gear motor rotated the entire apparatus at about 200 rpm. The bearings shown at the ends of the air cylinder were perforated to allow air to be fed to the charging piston and to allow inert gas to be fed to the reactor during the preheating period. The sample was simultaneously injected and sealed inside the reactor by operation of the air piston. Fig. 2 shows a cross section of the air cylinder and the adjoining portion of the support tube leading to the reactor. The sample carrier is shown in place at the right-hand end of the injection rod extending from the air piston. The piston is shown in the retracted position, as it would be prior to the start of an experiment. The small Teflon gasket which encircled the sample carrier at the end of the injection rod sealed the reactor when the sample was injected. This seal was maintained throughout the test by maintaining air pressure on the piston. The sample carrier was a 2-in. section of thin-walled, -in.-diam nickel tubing with an internal blank about 1 in. from the base and with the base end sealed.

Jan 1, 1969

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

H. Schwartzbart and W. F. Brown, Jr.—The authors have divided the effects of recovery on the true stress-true strain curve into two types; metarecovery, which effects only the first part of the curve or the yield strength, and orthorecovery, which effects the flow stress at any strain. Both of these are said to be true recovery effects, involve no recrystallization, and are explained by the removal of two different types of imperfections caused by work hardening. However, there seems to be some question as to whether the data are sufficiently conclusive to exclude, as an explanation of the authors' results, a mechanism based on the relief of residual stresses between the grains or slip bands and recrystallization. It appears that metarecovery could be interpreted in the same fashion as a customary interpretation of the Bausch-inger effect. The balanced system of internal stresses which exists between grains in a strained specimen due to varying orientation and, hence, yield strengths, of the different grains is responsible for a reduced yield strength in compression following pre-tension, and, similarly, for an elevated yield strength in tension following pre-tension. If the specimen is now heated so that the internal stresses are relieved by creep, then the yield strength in tension following tension will have been reduced and in compression following tension will have been raised. There seems to be a very strong case for the lack of recrystallization in the aluminum investigated by the authors, if one defines recrystallization as the presence of visually detectable new grains or accepts the X-ray evidence as conclusive. One must remember, however, that the appearance of spots on the back-reflection X-ray patterns cannot be taken as the time when recrystallization first started. The areas of recrystallized strain-free material must first have grown to a size large enough to give distinct spots on the patterns and this may take some time. Averbachl7 in an investigation of brass has shown that recrystallization can be detected by extinction measurements at temperatures lower than those based on hardness or X-ray line width determinations. It can be seen from fig. 10 that the rate of recrystallization is extremely low over a considerable time period at the onset of the process. Observations on the rate at which small amounts of recrystallization effect the flow stress would have given further insight as to whether undetectably small amounts of recrystallization might have been responsible for orthorecovery. Also, the question arises as to whether the effects observed in fig. 6 for various times and temperatures could not have been obtained if the time at 212°F were sufficiently long. In addition, the argument that the curve in fig. 10 is not sigmoidal seems weak in view of the scattering of the points. It is conceivable that an accurate determination of the curve for the first 100 hr would exhibit a relationship other than the one drawn. There is one point we would like to raise about the condition of the starting material. The authors annealed their material at 750°F for 15 min to remove the effects of any previous work hardening or machining strains. Reference to the work by Anderson and Mehl shows that this treatment may not have completely recrystallized the aluminum, so that the starting material may have had some strained areas. Higher temperatures or longer times may have been required to remove the effects of any small strains. We would like to mention some results of tests being conducted at the Lewis laboratory of the National Advisory Committee for Aeronautics in an investigation of the Bauschinger effect in relation to fatigue. Tests were performed on annealed electrolytic copper and several annealed brasses. Specimens were pre-strained 1 pct in tension and then tested in compression or tension with and without intermediate stress-relieving annealing treatments at 500°F for various times. Specimens heated at 500°F for 10 1/2 hr showed an elevation of the flow curve in compression and an approximately equal lowering of the flow curve in tension when compared with the curves for the un-heat treated specimens. After approximately 0.8 pct strain, all flow stresses coincided and were equal to the flow stress of the virgin material at this strain. This behavior is consistent with the metarecovery observed for aluminum by the authors and for which a residual stress model can be used. On the other hand, increas-

Jan 1, 1951

By Chas. A. R. Lambly

In the extreme northeast corner of the State of Washington, on the Canadian border, lies the Metaline mining district. This district is old in history, but young in production. Geology The Metaline district is a zinc-lead area of the replacement type in dolomite and limestone. The ore bodies of the Josephine horizon are in many ways similar to the ore bodies of the famous Tri-State zinc fields. The beds are faulted and folded and have varying low dips in varying directions, and underlie large areas of the district. History Production started in 1927 on a very limited basis. The property is now mining and milling 700 tons per day. The mine is opened by adit tunnels and a vertical shaft. As the ore horizons gained depth, it was necessary to sink inclines to follow the ore horizon (see Fig 1). From 1927 to date, approximately 600,000 ft of diamond drill was put down This work indicated that suficient tonnage existed to justify a redesigning of the whole operation, surface and underground. After four years of general study, the following program was planned: 1. A new mine entrance, which would be an incline, that could follow the ore body down at whatever pitch was necessary. The incline will be equipped with conveyors for the moving of ore and waste to the surface and with tractor-type locomotives for man and supply transportation. 2. The new incline also required a new type of mining which was developed and is now in use. It is called contour mining and will be described in a future paper. 3. The new incline exit would necessitate the moving of the mill and mine shops across the Pend Oreille River. This part of the program is now underway. The Incline The sinking of the incline was to start as soon as World War II ended and was as follows: The first leg of the incline was to be sunk from the surface 1600 ft on a 17" slope. The collar and first level at elevation 2180 ft, the second level at elevation 2000 ft, the third level at elevation 1875 ft, and the fourth level at elevation 1700 feet. From the 1700 ft elevation the incline was to flatten out to 12" for 400 ft to give the necessary depth for the ore pockets below the 1700 ft level and the necessary clearance for future sinking (see Fig 1 and 2). Due to lack of manpower in 1946, the program was changed and was as follows: A drift was driven from the old mine workings on the 1700 ft elevation in an easterly direction. At 1300 ft the drift was turned N 50" E and at this point a raise was driven 180 ft on a 50" slope. This raise intersected the Josephine horizon and commercial ore was encountered. At the 2000 ft mark, a main raise was driven, 245 ft on a 50" slope, and the 1875 ft elevation was cut. Exploration drifts were started on this level and production followed on a limited basis. The main drift at the 2500 ft point was turned N 35" E and ran parallel to and 10 ft east of and under the proposed incline line. At the proposed intersection of the drift and incline on the 1700 ft elevation, it was planned to raise the incline to intersect the 245 ft raise and to continue on to the surface, a distance of 1600 ft. When this proposed intersection point was reached, a heavy flow of water, approximately 800 gpm, was encountered and all work on the main drift face was stopped. This water flow flooded the main pump station in the old mine and the two lower levels with approximately 20,000,000 gal of water. The water was controlled and finally drained from the cave areas and lower levels after six months of pumping. After the heavy flow of water was encountered in the main heading, it was decided that the incline would have to be started from the surface, as originally planned, so that too much time would not be lost. The surface overburden had to be removed, a total of 6000 yards. A temporary dry house for 6 men was built. An 8 in. churn drill hole was intersected in the first raise driven from the 1700 foot elevation tunnel. Air and water lines were placed in this hole, and air and water were delivered to the collar of the incline from the mine working. The incline started down at 15 ft wide and 7 ft high through the Leadbetter slates. After sinking 4 sets, it was

Jan 1, 1950

By H. C. Gatos, A. D. Kurtz

WITH the growing interest in the mechanism of self-diffusion of metals, the study of accurate and convenient methods for determining self-diffu-sion coefficients appears highly desirable. It was with this objective in mind that the present investigation was undertaken. Gatos and Azzam1 employed an autoradiographic technique for measuring self-diffusion coefficients of gold. This method involved sectioning of the specimen through the diffusion zone and recording the radioactivity directly on a photographic film. Because of the very short range of the emitted ß rays in gold, the activity recorded on the film was essentially the true surface activity. With proper choice of the sectioning angle, sufficient resolution could be obtained and the entire concentration-distance curve recorded in one measurement. For the boundary conditions of the experiment, where an infinitesimally thin layer of radioactive material diffuses in positive and negative directions into the end faces of a rod of infinite length, the solution of the diffusion equation is C/Cn = 1/v4pDt exp (-x2/4Dt) where C is the concentration of diffusing element (photographic density in this case), C,, is the constant (depending upon amount of radioactive material), x is the diffusion distance, D is the diffusion coefficient, and t is the time. Thus, by plotting the logarithm of the concentration vs the square of the diffusion distance, a straight line results and the slope contains the diffusion coefficient. In this manner, the self-diffusion coefficient of gold can be obtained as a function of temperature. In the present investigation the results reported by Gatos and Azzam1 have been verified, and the autoradiographic technique has been further developed and applied for the determination of the self-diffusion coefficient of gold at a number of temperatures. Furthermore, the energy of activation for the self-diffusion of gold has been conveniently determined. . Experimental Techniques Preparation of Specimens: The inert gold of high purity was received in the form of a rod from which cylinders were cut and machined to a diameter of 0.500 in. The specimens were annealed to a suitably large grain size and the faces were surface ground prior to the deposition of the radioactive layer. The radioactive isotope Au198 was chosen. It was produced in the Brookhaven pile by means of the reaction Au197 + n ? Au108. It decays by ß emission (0.96 mev) to Hg108 with the subsequent emission of a y ray (0.41 mev). 70Au 108 ? 80Hg 108 + -1e°. The half life of the Au108 is 2.7 days so that a strict time schedule had to be maintained in order to secure sufficient activity until the end of the experiments. For this reason, initial activities as high as 10,000 millicuries per gram were used. The gold arrived in the form of foil and was evaporated onto one face of each gold specimen cylinder to a thickness of about 100A. A sandwich-type specimen was formed by welding two such cylinders together. Evaporation of Gold: The gold was evaporated under vacuum from heated tantalum strips which were bent in such a way as to limit the solid angle through which the gold was allowed to vaporize, thus insuring a more efficient utilization of the gold. The specimens rested on flat brass rings which had an inner diameter of 0.475 in. The entire specimen-holding assembly could be manipulated from outside the vacuum system by means of a magnet which attracted a slug of soft iron attached to the assembly. By evaporating inert gold on glass slides under conditions identical to those employed for the radioactive gold, it was found that the thickness of the films was about 100A. Welding: The welding was performed by hot pressing in a stainless steel cylinder. The inside of the cylinder was threaded and fitted for two plugs. The specimens to be welded were placed in the middle of the cylinder and two pressing disks, one at each end, were inserted to avoid shearing stresses as the plugs were tightened. Mica disks were placed between the pressing disks and the specimens to prevent them from welding. The plugs were then tightened with a hand wrench and the entire unit was placed in an argon stream for about an hour to remove the oxygen. The unit was then inserted in the center of an argon atmosphere furnace maintained at about 700°C and left there for about an hour. Because of the difference in the temperature coefficient of expansion of the two metals, as the temperature rose. the pressure on the specimen-rollple increased and a weld resulted Welding was generally satisfactory under the conditions described.

Jan 1, 1955

By E. H. Crabtree, Neil S. Parker

The custom milling plant of the Eagle-Picher Mining and Smelting Co. is at Sahuarita, Arizona, approximately 20 miles south of Tucson. It is connected by a 2-mile railroad spur to the main line of the Southern Pacific Railroad between Tucson and Nogales. The capacity of the plant is 500 tons per day. The mill is conventional except perhaps in the rather wide variety of ores treated. These vary from straight copper ores, from which only one concentrate is produced, and lead-zinc or copper-zinc ores from which two concentrates are produced, to complex gold-silver-copper-lead-zinc ores, which require the simultaneous production of three or lour concentrates. Custom ores are received in lots varying in size from a few truckloads to several carloads. Similar ores, after crushing and sampling, may be commingled, or individual lots may be milled individually. The ores are first dumped either into one of two 200-ton railroad bins, or into one of the two 75-ton truck bins. From these bins the lot of ore is individually crushed in a 24 by 16-in. jaw crusher to 3-in. size, and then to ½-in. size in a 3-ft Symons shorthead crusher. After crushing to ½-in., the ore is conveyed to the automatic sampling plant. This consists of three Vezin samplers in series, each successively cutting out 10 pct, 10 pct and 5 pct of its feed. After No. I sampler, the material passes through a mixing barrel and is then crushed to -in. in a set of rolls before passing to No. 2 sampler. Between No. 2 and No. 3 samplers, the ore is again mixed in a mixing barrel. The final sample, consisting of one pound per ton of ore, is taken to the laboratory, where it is further crushed to 1/8-in. in a coffeemill, and then riffled down to the size required for grinding in a pulverizer. The capacity of the crushing and sampling plant is up to 100 tons per hour, depending upon the character of the ore. After sampling, the ore is stored in five ore-storage bins, consisting of four 200-ton bins and one 175-ton bin. Each of these bins is discharged by means of belt feeders and conveyor to the ball mills, so that ores may be composited for milling in any required ratio, or milled separately by themselves. Fine grinding is done in one 6 by 4-ft Allis-Chalmers ball mill and one 8-ft by 36-in. Hardinge mill. These two mills both discharge to one 54-in. Akins Simplex High weir classifier. The classifier sands can be returned to either or both mills, so that flexibility in grinding for different ores is easily obtained. Flotation equipment consists of four 66-in. Fagergren machines for copper-lead roughing and six similar machines for zinc roughing. Lead-copper bulk concentrate is cleaned and recleaned in eight No. 18-S Denver machines, and zinc concentrate is cleaned in three 66-in. Fager-grens. Copper-lead differential separation

Jan 1, 1949

By E. H. Crabtree, Neil S. Parker

THE custom milling plant of the Eagle-Picher Mining and Smelting Co. is at Sahuarita, Arizona, approximately 20 miles south of Tucson. It is connected by a 2-mile railroad spur to the main line of the Southern Pacific Railroad between Tucson and Nogales. The capacity of the plant is 500 tons per day. The mill is conventional except perhaps in the rather wide variety of ores treated. These vary from straight copper ores, from which only one concentrate is produced, and lead-zinc or copper-zinc ores from which two concentrates are produced, to complex gold-silver-copper-lead-zinc ores, which require the simultaneous production of three or four concentrates. Custom ores are received in lots varying in size from a few truckloads to several carloads. Similar ores, after crushing and sampling, may be commingled, or individual lots may be milled individually. The ores are first dumped either into one of two 200-ton railroad bins, or into one of the two 75-ton truck bins. From these bins the lot of ore is individually crushed in a 24 by 16-in. jaw crusher to 3-in. size, and then to 1/2-in. size in a 3-ft Symons shorthead crusher. After crushing to 1/2-in., the ore is conveyed to the automatic sampling plant. This consists of three Vezin samplers in series, each successively cutting out 10 pct, to pct and 5 pct of its feed. After No. 1 sampler, the material passes through a mixing barrel and is then crushed to 1/4-in. in a set of rolls before passing to No. 2 sampler. Between No. 2 and No. 3 samplers, the ore is again mixed in a mixing barrel. The final sample, consisting of one pound per ton of ore, is taken to the laboratory, where it is further crushed to 1/8-in. in a coffeemill, and then riffled down to the size required for grinding in a pulverizer. The capacity of the crushing and sampling plant is up to too tons per hour, depending upon the character of the ore. After sampling, the ore is stored in five ore-storage bins, consisting of four 200-ton bins and one 175-ton bin. Each of these bins is discharged by means of belt feeders and conveyor to the ball mills, so that ores may be composited for milling in any required ratio, or milled separately by themselves. Fine grinding is done in one 6 by 4-ft Allis-Chalmers ball mill and one 8-ft by 36-in. Hardinge mill. These two mills both discharge to one 54-in. Akins Simplex Highweir classifier. The classifier sands can be returned to either or both mills, so that flexibility in grinding for different ores is easily obtained. Flotation equipment consists of four 66-in. Fagergren machines for copper-lead roughing and six similar machines for zinc roughing. Lead-copper bulk concentrate is cleaned and recleaned in eight No. 18-S Denver machines, and zinc concentrate is cleaned in three 66-in. Fagergrens. Copper-lead differential separation

Jan 1, 1947

By C. D. Rubert, W. J. Parton

A flotation plant was placed in operation in 1945 at the Tamaqua colliery of the Lehigh Navigation Coal Co. Inc., to recover fine anthracite which is discharged from the cleaning plant with the washery water.‡ In addition to the recovery plant, facilities were provided for the complete clarification of the washery water, recirculation of this clarified water for breaker use, and disposal of the refuse solids in a waste impounding dam. Fig I shows a view of the settling tanks and the flotation plant. Flow Diagram The flow diagram for the complete recovery project is given in Fig 2. All the waste water from the cleaning plant is collected in a sump A outside the breaker structure, from which a 7000 gpm pump B delivers it through a 16 in. line to a 75-ft diam hydroseparator C. The hydroseparator, acting as a classifier, is set to give a separation at approximately 200-mesh. The minus 200-mesh overflow is discharged by gravity into the 180-ft thickener D for final settling of the solids. The classifier underflow sludge is pumped to the flotation plant by a 6-in. quadruplex diaphragm pump E. A 10-ft diam hydroseparator F is used to make a second classification on the sludge solids at approximately 28-mesh. The underflow from this classifier containing the coarse particles is elevated by a 6-in. diaphragm pump G and is discharged on two 4- by 6-ft vibrating screens II. These screens are dressed with approximately 28-mesh cloth. Screen oversize product flows directly to the centrifuge that dewaters the cleaned froth. The screen underflow and the overflow from the 10-ft classifier flow to the flotation circuit. The flotation feed is conditioned in a 12 by 12-ft agitator tank J at a pulp density of I:2.33 (30 pct solids). Reagents are fed to the circuit by reagent feeder I. The conditioned pulp is then diluted to a pulp density of approximately I: 5 (18 pct solids) and is fed to two banks of four 100-cu ft froth flotation cells K for primary coal recovery and cleaning. Additional reagents from reagent distributor L are added to the feed weir-box of Nos. 2, 3, and 4 cells of each bank of flotation machines. Clean coal removed from these cells flows directly to the clean-coal sump. Dilute tailings from the primary cells is re-thickened in a 30-ft diam thickener M and is then retreated in a scavenger circuit for final recovery of coal. The scavenger circuit consists of a 6- by 6-ft agitator tank N and two banks of four 24-cu ft froth flotation cells 0. Coal froth from these cells flows to the dewatering equipment and the tailings flows to a vertical refuse pump which delivers it to the 180-ft diam waste thickener D. Dewatering of the coal products is accomplished in a 54- by 72-in Bird centrifugal filter P. The cake product is dropped onto a conveyor and is loaded

Jan 1, 1949

By Toshimi Yamane

The internal friction of cold-worked titanium iso-thermally annealed at temperature below the recrystallization temperature was measured. The internal friction was calculated from the half width of a resonance curve of the specimen which was vibrated transversally by the electromagnetic method. The experimental results were as follows: 1) The specimens annealed for a long time at temperature below the re crystallization temperature after cold working have the strain-amplitude dependent internal friction. 2) The internal friction increased by the cold working was decreased during the isothermal annealing. The reason of decrease of the internal friction is considered to be caused by the annihi-lation of lattice defects. 3) There is a linear relation between logQt-1/Q0-1 and (1/T)2/3 below the recrys-tallization temperature, where Q0-1 is the internal friction standing 24 hr at the room temperature after cold rolling, Qt-1 is the internal friction annealed at T°K for t min. 4) The hardness of the cold-worked titanium does not change by the annealing at 300°C for a long time but decreases by annealing at 400ºand 460°C. METALS, when cold worked, show sharp changes in physical and mechanical properties' The internal friction of cold-worked metals increases sharply and has a maximum value1,2 connected with working de- grees. The increased internal friction of cold-worked metals is recovered by annealing. This phenomenon is the well known effect called Köster effect. The recovery of the internal friction occurs earlier than the changes in tensile properties, hardness, or X-ray diffraction, and is very sensitive to the structure of a metal. The mechanism of the recovery at a temperature lower than the recrystallization temperature is being considered variously by many investigators: there are such views as the annihilation of dislocations by smith,' the rearrangement of dislocations mentioned by Nowick,4 and interaction of dislocation with point defects.5 Smith and Nowick also considered the interaction but it is so difficult for them to explain the rearrangement mechanism systematically, it being not considered a special model; therefore, we do not explain it quantitatively. Experiments measuring the recovery of the internal friction of cold-worked metals were performed by Gordon and Nowick6 on NaCl, and by Smith on copper. In addition, there are many studies, particularly those of measurements on copper by other investigators. There are comparatively many investigations on aluminum and iron which are the cubic system,'-' but only a few on metals of the hexagonal system.10 In view of this, I investigated cph titanium at room temperature and measured the internal friction after annealing isothermally at temperature lower than the recrystallization temperature. SAMPLES AND EXPERIMENTAL METHOD samples for the experiment were cut from a 6-mm titanium plate. The long direction of samples was

Jan 1, 1963

By H. T. Bowman

FOR more than 80 years the Bessemer process has depended upon the ability, skill, and judgment of the blower, although as early as the 1860's it was recognized that the process would benefit by some type of instrumental control.1 However, instruments with sufficient recording speeds did not exist, so the end-point determination was always dependent upon the blower's eye. This placed an obstacle in the way of precise experimental work, because of the absence of the necessary records and reference points as reported by Work.2 The use of the photocell provided the instantaneous record of the blow that made this experimental work possible and provided more scientific control for the process as discussed by Graham3' A brief description of the progress of the blow will illustrate the recording function of the instrument. The silicon in the iron is being oxidized during the first minutes of the blow, as pointed out by Henning4 in a table showing the order of metalloid elimination. The product of this oxidation is a solid that remains in the converter, so there is virtually no flame during this part of the blow. This low flame luminosity is illustrated by the flame recording shown in Fig. I, where the silicon blow is plainly marked. The dull flame of the silicon blow gradually gives way to the brilliant carbon flame as the increasing quantities of carbon monoxide formed inside the converter burn to dioxide upon contact with the atmosphere above the vessel. When the carbon reaches some low value under 0.20 per cent, there is insufficient monoxide formed to maintain the dioxide flame, so its intensity drops. Throughout the flame drop carbon continues to burn, until at some value around 0.05 per cent an arrest occurs in the recorded drop. This point has been designated as the end point. The period of time from this end point until the vessel is turned upon its side and blowing has stopped has been called the afterblow. This afterblow is used as a measure of the degree of metal oxidation, and uniformity demands that it be controlled within narrow limits. Iron and blowing conditions are likely to change several times during a turn, necessitating corresponding changes in end-point control. It is the purpose of this paper to discuss these changes, the factors that make them necessary, and their bearing upon the quality of steel. CARBON-FEO RELATIONSHIP In the Bessemer process oxidation relationships are precise. Fig. 2 shows a graph of the carbon-FeO relationship. The familiar "bomb-test" method, described by McCutcheon and Rautio,5 was used for obtaining these and all other dissolved FeO values herein reported, all tests being taken from the converter before deoxidation unless otherwise noted. All tests of 0.10 per cent carbon and above were obtained from metal blown for duplexing. McGinley and Woodworth6 reported iron oxide values for blown metal, but their tests were obtained by a different method than were those

Jan 1, 1942

By R. W. Raymond

to same extent, the assumptions tinderlying Dr. Ilu?ley's con alusions. These amrrmptions are: that 'the loss of metal per million tons of trafffc, depends, first upon the circrtnistances under which the rail is worn; secondly, upon the proportions of its various constituents, ancl that the anlorlnt of loss is afEect~d by eacb constitnent in a cer tain ratio, so that if the circunlstances were the same for all tlie mils, the wear per nliilion tons might he upproxi91ately expre~sed by an equation of the form I + Cc + Pp + SR + Mm = R, io wtlioh I is an unknown valne, dependi~.rg on the quantity of iron (and other ingre dients not determined) in the rail, and assumed to be constant for all the rails ; c, p, s, and m are the experimentally determined quan tities of carhon, phosphorus, sulphur, and manganese, as tabulater1 in YIates VT and VII of Dr. Dudley's paper; and R is the experirnen tdlly dcterlnincd wear per million tons; while C, P, S, and M are onknown wfficients. In other words, it is assunled that the differ ence in wear is proportional to a difference in c, p, s, or m, and that the effects of a change in the amonnt of either are independent of the amount of the rest-—within the experinlental limit5 of the problem. It is also assr~med that sulphar, copper, and other ingredients, not determined, are qually present in all the rails, or at least {lo not affect the wear, since I is taken as constant. Dr. Dudley tacitly assumes the coefficient6 C, P, S, and M to be positive; and assigns certain valries to them, by means of which he redom t.he equation to the form I + Pa: = R, x being equal to cc + Es +Mm i Pp, or tjje uanjbe,. of so-called phosphorus units in the rail. But we do not have R directly given under constant circumstances. The varying weights (per engine, car, or train) and the varying epds, we must neglect for lack of data, and assume that in these rwpects the rails examined have been treated srlbstantially alike. But there remain the varying conditions as to track, which mnst he elirninsted. Dr. Dudley gives six clrlsses, four of which contain 8 rails each, and two 16 rails each. Beginning with the 6~st (tangent grade), take the mean of the figures expressing wear for that clam; and continaing tliis process through the other five, we obtain six expressions in quantity of loss 'by wear, which we assome tc, represent, in their differences, the varying conditions of the trarli, with respect to grade and direction. We now take the mean of these moans (giving double weight to the gmiip containing 16 ohwrvafieras). This general rnean is the 10 of metal per million tons of trafio for a rail of avorage constitution under mean ciroumstances.

Jan 1, 1881

By Rollin E. Hook, Attwell M. Adair

The response of CrzO3 and C~304 to various heat treatments was studied in are-melted iodide chromizim over the temperature range 1000" to 1750°C. These oxides, which are present as impurity phases in this material, were identified by X-ray diffraction teclzniques which were supplemented by optical metallop-aphy. As a function of increasing temperature, Crs04 is first observable in samples annealed at 1300°C and coexists with Cr2O3 (the low-temperature oxide) over a temperature range exceeding 200°C. As the temperature decreases, Cr3O4 dissolves with the concomitant precipttation of Cr2Y2. Both oxides precipitate predominantly at pain boundaries. The reactions which occur are involved with at least ternary equilibria, possibly due to iron which is present as an impurity in arc-melted iodide chromium. HILTY, Forgeng, and Folkman' reported in their investigation of the Fe-Cr-0 system that Cr3O4 (with about 8 pct Fe substituted for chromium) is a primary phase found in alloys with 9 or more pct Cr. They reported that this phase is stable only at high temperatures and that below the liquidus Cr3O4 is disproportionated into Cr2O3 and chromium-rich metal for both Fe-Cr-O alloys and in oxygen saturated pure chromium. Further, they proposed that CrsO4 forms by a peritectic reaction between Cr2O3 and the liquid. On the other hand, Hook, Garrett, and Adair2 found in their investigation of impurity phases formed in "pure" chromium (material consolidated from iodide chromium crystals) that Cr3O4 forms intergranularly and is stable as low as 1500°C which is 375OC below the melting point of chromium. The purpose of the research described herein is to determine the temperature range of stability of Cr3O4, and to show the nature of its decomposition. This further investigation indicates that Cr3O4 undoubtedly occurs in this material as low as 1300°C. The chromium studied was consolidated and fabricated from iodide chromium crystals (ICr-5) and contained Fe r 135 ppm, Si = 20 to 100 ppm, and 0 = 35 to 137 ppm. A complete chemical analysis is given elsewhere.' Annealing was conducted in 1 atm of purified helium and all samples were rapidly cooled (-200°C per sec) by withdrawing them from the furnace hot zone under a high flow rate of helium. The details of the electrolytic-etching technique and electrolytic-digestion techniques for preparation of insoluble residues for X-ray examination are given elsewhere also.' EXPERIMENTAL RESULTS The Starting Material. The as-swaged rod (final swaging done at 900°C) had a wrought grain structure and contained a dispersion of CrzO3 inclusions of maximum particle size of about 2 or 3 p, Fig. 1. The microstructure also contained a dispersed

Jan 1, 1964

By C. E. Westley, R. R. Beebe

Recent works by Plaksh et al.,1,2 Glembotsky,3 and others have renewed interest in the effects of oxidation on the surface activity of the sulfides. Since considerable supporting data are available on galena-potassium ethyl xanthate, this system is being studied at South Dakota School of Mines and Technology by contact angle measurement, using the technique of McGlashan and McLeod.4 The contact-angle method is well adapted to investigation of the influence of small amounts of oxygen on the establishment of a stable contact angle on galena in potassium ethyl xanthate solution. Samples of massive galena containing less than 0.001 pct Cu, 0.001 pct Ag, and 0.01 pct Zn are mounted in castable plastic and ground and polished manually in a glove box containing the desired proportions of oxygen and purified nitrogen. Oxygen and nitrogen contents of the test atmosphere are determined with an Orsatt analyzer. In this way a reproducible surface is created in contact with whatever oxygen concentration is desired. Water and all reagents are prepared and stored in the test atmosphere. An absorbent is used to control carbon dioxide that might be present. Final polishing is done with levigated alumina on a glass plate. The prepared sample is placed in the test solution and transferred to the contact angle apparatus in a sealed box, and the test is conducted while both sample and solution are maintained under a slight positive pressure of the test atmosphere. Table I gives the results of contact angle measurements made at various 02-Nz concentrations.5 Each value of contact angle is the average of at least six individual measurements made with different bubbles at different locations on the sample surface. A period of 20 to 25 min has been found by preliminary tests to be sufficient to permit develop- ment of maximum angle, and all measurements are made after at least this much time has elapsed. Exposure of prepared samples to pure water under the test atmosphere before exposure to the xanthate results in a small but measureable and consistent reduction in contact angle. This is particularly true in the oxygen-deficient atmospheres; for example, at 2.2 pct O2 such water contact reduces the average angle about 8" from that obtained by immediate testing in xanthate. The general trend of increasing contact angle with increasing oxygen concentration corresponds to the results of Plaksin et a12 The absence of diminish-ment of contact angle at very high oxygen concentration has been attributed to the high concentration of xanthate per unit of galena surface: At oxygen concentrations below 1 pct (the limit of accuracy of the Orsatt analyzer), no contact angle is obtained. Furthermore, no contact angle is obtained at any oxygen concentration in the absence of xanthate. This result seems to be in disagreement with those cited by Plaksin.1 Further work on the interaction of galena and potassium ethyl xanthate or a similar collector as influenced by oxygen is contemplated. The true nature of the interrelation is as yet unknown. For example, it is not known whether the governing oxygen reaction is with the mineral, with the reagent, or with both.

Jan 1, 1961