Search Documents

By N. T. Burdine

Formulas for calculating relative permeability from pore size distribution data are derived from basic laws of fluid flow ill porous media. The tortuosity factors that appear in the equation5 are described in. terms of the physical properties of tile medium and the saturations of the contained fluids. Procedures for calculating and methods for measuring the tortuosity factors are discussed. Values of relative permeability calculated by the formulas art: compared with results obtained by experimental measurements I INTRODUCTION Recently, several investigators have derived relative permeability equations from Darey's and Poisenille's Laws in which some, physical factor or factors describing the porous system appear. The factor that has caused the greatest amount of comment, and which is probably least understood, is the tortuosity of the fluid {lath ill the porous sample. Values of the tortuosity factors appearing in the equations range from a constant for all condition- of the fluid flow system to an inverse function of the pore radii. It is the purpose of this paper to compare wine experi~i~cntslly determined relative permeability curves with those calculated by a method which utilized capillary pressure infortmation. The capillary pressure data were obtained prefer.. ably from pore size distribution information as determined by mercury injection but. in some cases, in the absence of suitable mercury injection information. data were taken from measurements made by the porous semi-permeable diaphragm method. The physical significance of certain tortuosity concepts is inferred and the determinations of the tortuosity factors from pore size distribution data and by electrical measurements are discussed. THEORETICAL BACKGROUND In previously reported studies on pore size distribution in petroleum reservoir rocks. by the author and co-workers ail equation was derived relating specific permeability. k, to pore entry radii, R, porosity. . tortuosity factor. .,, and incremental pore volume. V. The equation is where being the "effective" length of the flow path in the porous sample. and L the length of the porous sample., The constant. 0.126. is a units conversion factor. (This definition of tortuosity factor X, = L L does not conform to all such definitions found in the literature. Fly similarity, in a two-phase system. the effective permeability of the wetting-phase.

Jan 1, 1953

By H. Rush Spedden, A. M. Gaudin

Although the number of minerals that are ferromagnetic‡ or highly paramagnetic is strictly limited, it has been known for some time that many minerals have slight but supposedly characteristic magnetic susceptibilities. With the exception of pyrrhotite, however, sulphides have been thought nonmagnetic. A new magnetic separator has been made available recently in limited quantity to research laboratories. This device, the Frantz Isodynamic Separator, has been used for the separation of various non-sulphides from each other. Its application to the separation of sulphides, however, does not seem to have been reported. In the Richards Mineral Dressing Laboratories, the success achieved through the use of this device in separating associated sulphides has been so startling as to lead us to believe that it constitutes a magnificent adjunct to heavy-liquid separation and to quantitative mineragraphy as a tool for the mineral investigator. The separator (Fig. I) consists of: 1. A powerful magnet, the strength of which can be adjusted by, means of a rheostat; 2. A vibrating chute of nonmagnetic metal on which the mineral to be separated is made to flow (Fig. 2); 3. A feed bin and adjustable feeder; 4. Receptacles for the collection of products; 5. Means for changing, setting, and accurately reading the two slopes of the chute; viz., the cross slope and longitudinal slope. The separator is made operative by the special shape of its pole pieces, which ensures a strongly converging field. It is said by the makers of the machine that the pole pieces apply a constant mechanical force to a particle of given susceptibility, regardless of its position in the operating space of the separators." Susceptible particles, therefore, behave as though of lower specific gravity than under ordinary circumstances. This effect, combined with the slopes of the chute and the action of the vibrator, causes a stratification not unlike thai obtainable on a shaking table. The chute is of rectangular cross section, and shallow; it is broadened toward the discharge end and divided longitudinally by a partition into two compartments that lead to the collecting receptacles. Although the separator probably can be used to make separations at fairly coarse

Jan 1, 1943

By H. Rush Spedden, A. M. Gaudin

Although the number of minerals that are ferromagnetic‡ or highly paramagnetic is strictly limited, it has been known for some time that many minerals have slight but supposedly characteristic magnetic susceptibilities. With the exception of pyrrhotite, however, sulphides have been thought nonmagnetic. A new magnetic separator has been made available recently in limited quantity to research laboratories. This device, the Frantz Isodynamic Separator, has been used for the separation of various non-sulphides from each other. Its application to the separation of sulphides, however, does not seem to have been reported. In the Richards Mineral Dressing Laboratories, the success achieved through the use of this device in separating associated sulphides has been so startling as to lead us to believe that it constitutes a magnificent adjunct to heavy-liquid separation and to quantitative mineragraphy as a tool for the mineral investigator. The separator (Fig. I) consists of: 1. A powerful magnet, the strength of which can be adjusted by, means of a rheostat; 2. A vibrating chute of nonmagnetic metal on which the mineral to be separated is made to flow (Fig. 2); 3. A feed bin and adjustable feeder; 4. Receptacles for the collection of products; 5. Means for changing, setting, and accurately reading the two slopes of the chute; viz., the cross slope and longitudinal slope. The separator is made operative by the special shape of its pole pieces, which ensures a strongly converging field. It is said by the makers of the machine that the pole pieces apply a constant mechanical force to a particle of given susceptibility, regardless of its position in the operating space of the separators." Susceptible particles, therefore, behave as though of lower specific gravity than under ordinary circumstances. This effect, combined with the slopes of the chute and the action of the vibrator, causes a stratification not unlike thai obtainable on a shaking table. The chute is of rectangular cross section, and shallow; it is broadened toward the discharge end and divided longitudinally by a partition into two compartments that lead to the collecting receptacles. Although the separator probably can be used to make separations at fairly coarse

Jan 1, 1943

By Frank Foote, Eric R. Jette

In a recent article,1 the authors reported the results of an X-ray investigation on the range of solid solutions that occurs in the iron-oxygen system in the vicinity of the compound FeO, which frequently is called "wüstite." The object of that investigation was primarily to study the unusual type of solid solution phenomena involved in this range. Briefly summarized the results were: 1. The NaCl type of lattice found by earlier workers was confirmed. 2. The lattice dimensions decrease rapidly with decrease in iron content. 3. No alloy that was a homogeneous single phase was ever found at compositions beyond 76.80 per cent Fe, while the theoretical iron content of FeO is 77.73 per cent Fe. 4. Measurements of the densities and lattice constants led to the conclusion that the form of substitution was complex, an FeO group being replaced by oxygen. Such a substitution, of course, is equivalent to removing an iron atom (or ion). The ideal unit cell of FeO can be considered as containing four groups of FeO and, thus, when this type of substitution takes place, there remain in the unit cell three FeO groups and an oxygen, or a total of seven atoms with a gross formula of Fe3O4 instead of the original Fe4O4. 5. This was the only interpretation that would fit the experimental results and at the same time be consistent with (a) the previously determined fact that the FeO lattice is ionic (i, e., consists of Fe++ and O? ions) and (b) the chemical fact that as the oxygen content of the substance increases, ferrous iron becomes oxidized to ferric iron. The experimental results of this investigation are included in Fig. 1. The purpose of the present investigation was to determine the limits of this homogeneity range by means of the X-ray structure analysis. This method has been applied frequently to the study of solid solutions by Westgren and his coworkers as well as by other investigators. The principle is simple: if the change in lattice constant with composition is

Jan 1, 1933

PAUL. D. MERICA, Bayonne, N. J. (written discussion*)..-The mode of intercrystalline oxidation which the authors" have so well observed and described is characteristic of nickel that has been exposed' to: the action of an oxidizing atmosphere at higher temperatures, such as, those at which; it is annealed or heated for rolling or forging. Oxidation under such conditions proceeds inward from the surface along the, crystal boundaries' producing a net-work, probably of oxide; which causes a very brittle condition of this surface material. This, in turn, generally results in surface cracking and checking during further, rolling and a defective sheet or other product is produced. An example of this is shown in Fig. 2, which shows the surface, of a badly surface-cracked sheet of nickel produced by incorrect heating con-ditions. A cross-section of this sheet etched with nitric acid is shown in Fig. 1, which reveals the intercrystalline oxidation network adjacent to both surfaces.These layers are so brittle that it is not possible to deform them by rolling without severe cracking along these lines or, planes of weakness. The best, and possibly only, remedy for this condition lies in its prevention by the maintenance of a neutral soft flame for heating and annealing nickel during the entire course of its manufacture. I should like to suggest that, those making microscopic investigations of nickel and nickel-rich alloys try the use of acetic-acid .solutions of nitric acid for etching these metals rather than aqueous solutions, of nitric acid. I have found that a solution containing 50 per cent. nitric acid, from 25-45 -per. cent. acetic acid, and from 25-5 per cent. water gives excellent results with. Wrought and cast nickel and Morsel metal and superior results to those obtained with nitric acid, alone. The acetic. acid seems to inhibit the passivity that nickel often assumes toward nitric acid and much more uniform etching may, be obtained. The proportions of nitric and acetic, acid may be varied somewhat from those given without mate-rially altering the quality of the etching, although without any distinct improvement in it.

Jan 12, 1919

By H. C. Hardison

The Yates pool, Pccos County, Texas, has greater potential capacities than any other field in the United States. This field is notable for the large return it yields on capital invested, for low production costs and for the orderly and conservative manner in which it was developed and continues to be operated. The proven area is 20,000 acres and there are 392 producing wells, or approximately 1 well to 50 acres. The theoretical daily potential is 5,250,000 bbl. as determined by l-hr. open-flow gages. Individual well gages vary from a few barrels to 8500 bbl. per hour, and well depths range from 1000 to 1800 ft. The greater part of the production is from a very porous limestone, and by agreement no productive well has penetrated the lime more than 225 ft. The forces driving the oil from the formation to the surface are hydrostatic head, expanding gas or a combination of the two. The degree of effectiveness of either depends upon the structural position of, and porosity encountered in, the individual wells. Approximately 95 per cent. of the wells in the field flow naturally. The pipe line outlet of the field at the present time is 100,000 bbl. per day, which is less than 2 per cent. of the daily potential. Difficulties and Principles of Probation It became evident during the first year of the development of this field that operators would have to devise a scheme to allocate pipe line runs equitably among their different properties. When the idea of proration was first inaugerated, the matter of spacing wells was given consideration. This was given up through fear of legal difficulties. Storage was also a question that was given considerable thought, and a plan was finally developed which went into effect Oct. 1, 1927. It was decided that the oil runs should be prorated according to the total potential capacity of all the wells which the several operators had in the field. The potential capacity of the wells was measured by a l-hr. open-flow gage. All runs to storage by an operator were deducted from his daily allowance.

Jan 1, 1931

By Elliott J. Roberts

In spite of the fact that the percentage of true colloids in an ore grind is very small,' these pulps exhibit many of the properties of true colloidal suspensions. A quartz particle, appreciably finer than 10 microns in diameter, has a settling rate so low that at a dilution of 5:l or over, the capacity of a settling tank to settle such particles would be uneconomical if the individual particle rate prevailed. However, by grouping the finer particles into aggregates or flocs, the settling rate can be increased to an economical value. The colloidal chemistry of pulp thickening is thus chiefly concerned with particles having diameters of between 1 and 10 microns, although particles as coarse as 40 microns in diameter are more or less involved. These particles must be associated in such a manner that they settle at an economical rate and give a clear, supernatant liquid or overflow. The treatment of the subject may be divided into three phases, cach phase having a more or less different colloidal aspect. The first phase is the problem of getting the pulp or suspension into the proper condition of flocculence; the second is the behavior of the flocculent pulp in its initial and intermediate stages of settling; the third is the behavior of the flocs in the find period of settling or thickening stage. Let us look first into the methods and mechanism of obtaining the flocs and then consider their behavior and properties. Flocculation Colloids are merely ordinary substances reduced to a very small particle size, the upper limit being placed by definition at 1 micron (0.001 mm.) diameter by the soil chemists and at from 0.2 to 0.1 micron by various other colloid chemists. The lower limit is reached only when the particles approach molecular dimensions. The term L'colloid" should not necessarily imply lack of crystallinity. Particles as small as 0.01 to 0.02 micron give perfect X-ray patterns, while with 0.005 micron particles the bands on the powder photograph are merely broaderled and diffused.2

Jan 1, 1935

By Franklin J. Kay

Introduction The methods used in surface, mining vary throughout the world, depending on many variables such as: the types of over- burden materials, the depth of the overburden, the thickness of the seam, and other operational choices, both financial and functional. However, the stripping machines are typically draglines, stripping shovels, excavators, scrapers, loaders, and bulldozers. In all cases the economic feasibility of mining thin seams depends on the market needs, the market location, the equipment used, the mine management, the quality of the coal, and the labor market. Slight negative combinations of these parameters have closed many mines while positive combinations allow others to exist. The limited mobility or slow movement of large stripping shovels, draglines, and bucket wheel excavators make them more economically fitted to areas where large quantities of overburden are to be moved. This is necessary to keep the transfer and setup time between pits a negligibly small percent of the total operational time. Equipment such as the scrapers, loaders, backhoes, trucks, and bulldozers that are either very mobile or can be trailered is more versatile and can be used in the smaller area mines.* Mobile equipment is also more practical in areas with shallow overburden because of the constant movement required while removing overburden. In thin coal seams the equipment is usually paired such that the operational equipment can be listed as: (1) dragline-loader, (2) shovel-truck- loader, (3) scraper-loader. (4) loader-truck-loader, or (5) loader-loader. In these operations the overburden is removed with the first machine(s) of the pairing and the loader or loaders are used for coal production. Recent articles in Coal Age (Chironis, 1978) and Mining Engineering (Wiebmer, 1978) have discussed varying philosophies in mining similar seams of coal. One operator uses draglines for competitive mining while the other uses scrapers for the same purpose. Both cite strong cases sup- porting their choice of equipment as good sound economic decisions and their success supports their choices. The drag-line operation is adding new larger draglines to decrease the cost of mining, rather than to increase coal production. The scraper operation has also gone to more and larger scrapers for basically the same reasons. These operations and all

Jan 1, 1981

By S. D. Dahlgren

The plasticity of unalloyed P plutonium was studied by evaluating the strain-rate-hardening exponent, m, in the equation Values of m up to 0.33 and tensile elongations up to 680 pct were obtained for ß plutonium formed directly from the a phase. Casl bars that were cycled and tested had lower flow stresses and higher values for than uncycled bars , hut their total plastic elongations were not as great as expected because of premature failure at voids formed during cycling. Flow stresses were higher and m was lower (m = 0.15) for 9 plutonzutn formed from the y phase. ThE strain-rate-hardening exponent for plastic flow of p plutonium was determined as a function of strain rate, test temperature, and heat-treating history, and it was related to the rather large plastic elongation found previously for some plutonium tensile samples. Gardner and ~ann' obtained tensile elongations of up to 620 pct for P plutonium samples which had been completely transformed from the low-temperature a phase to the P phase before testing. Such a large percentage elongation is unusual for unalloyed metals or single-phase alloys.' The a phase is stable below approximately 112°C and (3 is stable between approximately 112" and 190"c.~ Both phases have mono-clinic structures. A temperature of 160°C is 0.58 of the effective absolute melting point, 475°C) of the p phase. The effective melting point is obtained by considering the enthalpy and entropy changes associated with the higher-temperature phase transformations and it is not the same as the experimental melting point of the highest-temperature allotrope of unalloyed plutonium. Nelson, Bowman, and Bierlein observed a striking difference between the ductility, as well as other mechanical properties, of p plutonium formed from the next higher-temperature phase (y) and the ductility of /3 plutonium formed from the a phase. The total elongation of /3 plutonium formed from the y phase was less than 5 pct. Earlier, the creep rate of 13 plutonium formed from the a phase was shown to be 200 to 500 times faster than the rate for 0 formed from y for the same test temperature and stress.

Jan 1, 1969

By E. S. Bardwell, R. J. Lapee

Twenty years ago, W. T. Burns, in his paper presented at the Butte Meeting of the Institute,' discussed the general scheme then in use in the electrolytic copper refinery of the Anaconda Copper Mining Co. at Great Falls, Mont., for removing impurities from tank-room electrolyte and controlling its acid content. Since then marked changes have taken place in copper-refinery practice at Great Falls. The electrolytic copper refinery in use in 1913 has been replaced by a new and entirely modern plant capable of producing up to 27,000,000 Ib. of cathode copper per month. With the building of the new plant in 1916, the treatment of converter anodes was discontinued. At first the substitution of refined anodes for converter anodes resulted in a decrease in the impurity content of the anodes, but as time went on, changes in metallurgical practices at the smelter resulted in substantial increases in the impurity content of the anodes. The leaching of the silver slime to remove copper before shipment to Raritan for treatment further added to the purification problem. The fact that the scheme of purifying electrolyte which Mr. Burns described in his paper has proved adequate for our needs under a wide variation of conditions speaks well for its essential soundness. Method of Purification Briefly, the method adopted for purifying tank-room electrolyte at Great Falls has been as follows: Each day a certain volume of tank-room electrolyte is run off and sent to the purification plant, where it is boiled down to approximately 46' 136. The concentrated electrolyte is then sent to crystallizing tanks where the bulk of the copper is crystallized out as copper sulfate. The mother liquor is then passed through insoluble anode tanks to remove the last of the copper and most of the arsenic and antimony. It is then either returned to the tank room direct or boiled down to 55' Bé, the iron and nickel salts crystallized out and the mother liquor returned to the tank-room circuit as restored acid. Prior to 1930 all of the evaporating was done in lead-lined tanks 13 ft. in diameter by 4.5 ft. deep, provided with lead heating coils through which steam at 30 lb. gage pressure was circulated.

Jan 1, 1934

By Ben-Zion Weiss, Melvin R. Meyerson

FATIGUE crack propagation in some aspects can be viewed as being a result of localized plastic deformation concentrated near the tip of the crack.' Deformation is influenced by microstructure which in turn can affect the fatigue crack growth significantly. To study the effect of localized microstructural changes on fatigue crack propagation, cantilever-type notched specimens were subjected to cyclic bending at constant load amplitude. The extent of fatigue crack propagation was obtained by measuring the length of the crack by periodic observation with a microscope on the polished side of the sample,2"4 and these data were used in preparing the curves in the figures which follow. Figs. 1 (solid lines) and 2 show experimental results obtained in austenitic type 302 stainless steel containing higher than standard carbon (0.24 pct C) and 310 stainless steel. Both steels were homogenized for 8 hr at 1120°C and then water-quenched in order to prevent the precipitation of carbides. Fig. 3 shows experimental results obtained on 9440 low alloy steel in the normalized condition and in the quenched and tempered (580°C) condition. Indications of microstructural influence can be seen in scattering of the experimental data. The degree of scattering depends on both the microstructure and the amount of cyclic stress applied to the sample. For microstructures which are more easily deformed plastically, e.g., normalized or annealed as compared with hardened and tempered structures, the scattering is greater. Similarly, higher stresses produce greater scattering in the results, regardless of whether the cause of the stress increase is due to initial loading conditions or the growth in crack length. Scattering is believed to be a result of partial redistribution in the stress field around the tip caused by plastic deformation. This opinion is borne out by much smaller scattering of experimental results in the austenitic 302 high-carbon (0.24 pct C) steel. In this steel, plastic deformation in the neighborhood of the crack causes partial mar-tensitic transformation of metastable austenite,5 which in turn restrains further plastic deformation. As a result, the stress redistribution around The tip is reduced. Partial martensitic transformation was confirmed

Jan 1, 1969

By T. G. Digges, C. L. Vold, M. R. Achter

A study was made of the effect of the growth conditions on the perfection of single crystals of niobium (columbium). Dislocation densities, determined by means of double-crystal diffractometer measurements , were not greatly affected by the method of crystal preparation but could be reduced by annealing treatments. However, the size, sharpness, and tilt angles of the substructures, observed with X-ray reflection macrograph, were sensitive to variations in growth procedures as well as to subsequent thermal treatments. Although the dislocation density was the same in both types, there were more low-angle bound-aries in crystals grown by zone melting than in those prepared by strain anneal. Mechanisms to account for these observations are discussed in terms of dislocation movements. A planned study of the structure-sensitive properties of refractory metals required the use of single crystals of a high degree of structural perfection and, for ease of handling, of large cross section. It appeared that the strain-anneal technique could satisfy both of these requirements. First, crystals grown in the solid state have been reported to be more perfect than those obtained from the melt.' Second, the diameters of rods which may be produced by zone melting should have a theoretical limit determined by specific gravity, thermal conductivity, and surface tension, while the diameter of strain-annealed rods is limited only by practical considerations. Previously it was shown that niobium (columbium) single crystals of 1 in. diam2 may be grown by strain anneal, compared to the 0.5 in. maximum diameter achieved by zone melting, as reported for molybdenum by Belk.3 The current research was undertaken to investigate and optimize the effect of various process variables on the perfection of 1/4 and 1/2-in.-diam niobium single crystals grown by strain annealing and to compare their perfection to those grown by zone melting. Characterization of these crystals was more conveniently accomplished by means of X-ray than by metallo-graphic techniques. EXPERIMENTAL PROCEDURE Specimen Preparation. Zone-melted crystals of 1/4 in. diam were produced by the standard electron-beam zone-melting technique. The swaged and cleaned rods were outgassed, in the solid state at a temperature near its melting point, at a rate of 12 in. per hr, and single crystals were grown by making two molten passes at 2 in. per hr. By maintaining a zone length of 4 to % in., very uniform single crystals several inches long were obtained. For the strain-annealed crystals, an induction heater was used, in preference to other types of heating, to take advantage of the good penetration of large sections. A five-turn coil, 1 in. long, operating at 10 kc and powered by a motor generator, was contained in a vacuum chamber. The rod, suspended from the upper end, was raised through the coil for both recrystallization and crystal growth. In preliminary work single crystals of the same material were also grown with single and multiturn coils powered by a 450-kc generator. A vacuum of 2 X 10-6 Torr was maintained at temperatures up to 2400°C. Starting with electron-beam-melted ingots of 21/2 in. diam, the analysis for which is given in Table I, the material was cold-swaged to the desired cross section of 1/4 and 1/2 in. diam and then recrystallized. The rods were then strained in a tensile machine and converted to single crystals by passing through the induction coil. As with zone melting, control of orientation is possible by the use of special procedures. Other investigators, see for example Williamson and smallman,4 have reported that orientation control may be achieved by a bending technique. In the present work the strained rod is partially lowered through the coil to start the growth of the crystal. Then it is removed and bent at a point in the poly crystalline portion. Finally, it is returned to the chamber and growth is continued "around the corner". This procedure has certain limitations. If the bending operation exceeds the critical strain, recrystallization may take place. Also, the amount of bending which can be imparted to the rod is limited by coil geometry, and up to now has been 10 deg. However, by repeating the bending and growing operations it should be possible to attain any desired orientation. In preparation for X-ray examination, single crystals were sectioned and planed by means of the spark-erosion technique. To obtain the maximum reflected intensity, the (110) plane was exposed for examination. They were then etched 3 to 5 min in a mixture of con-

Jan 1, 1967

By C. H. Samans, G. F. Tisinai, J. K. Stanley

The addition of nitrogen (0.10 to 0.20 pct) to Fe-Cr-Ni alloys of simulated commercial purity results in a real displacement of the u phase boundaries to higher chromium contents. The effect is small for the (Y + s)? boundary, but is pronounced for the (y + a +s)/(y + a) boundary. Although there is an indication of an exceptionally large shift of the n boundaries to higher chromium contents, especially in steels with nitrogen over 0.2 pct, the major portion of this apparent shift results from the fact that carbide and nitride precipitation cause "chromium impoverishment" of the matrices. The effect of combined additions of nitrogen and silicon to the Fe-Cr-Ni phase diagram is demonstrated also. Nitrogen can nullify the effect of about 1 pct Si in shifting the (y + o)/? phase boundary to lower values of chromium at all nickel levels from 8 to 20 pct. NItrogen can nullify this U-forming effect of about 2 pct Si at the 8 pct Ni level, but not at the 20 pct Ni level. The alloys studied were in both the cast and the wrought conditions. There are indications that the u phase forms more slowly in the cast alloys than in the wrought alloys if both are in the completely austenitic state. The presence of 6 ferrite in the cast alloys accelerates the formation of U. Cold working increases the rate of o formation in both cast and wrought alloys. THE major improvement in Fe-Cr-Ni austenitic alloys in recent years has been in the addition or removal of minor alloying elements to facilitate better control of corrosion resistance, sensitization, and heat resistance. One shortcoming of the austenitic Fe-Cr-Ni alloys, which never has been completely circumvented, is their propensity toward u formation. In the AISI-type 310 (25 pct Cr-20 pct Ni) and type 309 (25 pct Cr-12 pct Ni) steels, sufficient amounts of u phase can form, if service or treatment is in a suitable temperature range, to cause severe embrittlement. Also, there is a growing conviction that this phase may be contributory to some unexpected decreases in the corrosion resistance of certain of the 18 pct Cr-8 pct Ni-type steels. The present paper discusses the effect of nitrogen additions on the location of the (r+u)/d and the (y+a+u)/(y+a) phase boundaries in the ternary Fe-Cr-Ni system, for cast and wrought alloys of simulated commercial purity, and in similar alloys containing up to about 2.5 pct Si. The objective is to define compositional limits for alloys which will not be susceptible to u formation when used near 1200°F (650°C). An excellent review of the early studies of the u phase in the Fe-Cr-Ni system has been compiled by Foley.1 Rees, Burns, and Cook2 have determined a high purity phase diagram for the ternary system, whereas Nicholson, Samans, and Shortsleeve3 are- stricted themselves to a portion of the simulated commercial-purity phase diagram. Both groups of investigators show almost an identical position for the commercially significant (y+u)/y phase boundary. Further comparison of the work of the two groups indicates that, below the 8 pct Ni level, the commercial alloys have a decidedly greater propensity toward u formation than the high purity alloys. The two groups of workers agreed that both the AISI-type 310 (25 pct Cr-20 pct Ni) and the type 309 (25 pct Cr-12 pct Ni) steels are well within the (y+~) region and that the 18 pct Cr-8 pct Ni-type alloys straddle the U-forming phase boundaries. Nicholson et al.3 showed, in addition, that these boundaries shift toward lower chromium contents if greater than nominal amounts of silicon or molybdenum are added. The effect of nitrogen on the location of the s phase boundaries in the Fe-Cr-Ni system has not been known with any certainty. In 1942, an approach to this problem was made by Krainer and Leoville-Nowak,' but at that time they apparently were unaware of the slow rate of s formation in strain-free samples and aged their samples for insufficient times, e.g., 100 hr at 650°C (1200°F) and 800°C (1470°F). For this reason, it would be expected that their (y+ u) /y boundary would be shifted toward lower chromium contents (restricted ?-field) when equilibrium conditions were approximated more closely. Procedure for Studying the Alloys The alloys used were prepared in the following way: Heats of 200 lb each were melted in an induction furnace. A 5 lb portion of each heat was poured into a ladle containing an aluminum slug for de-

Jan 1, 1955

By D. R. Irving

Prior to this time, ample supplies of high grade mineral fillers, such as clay, have been available close to consuming centers. Now depletion of these accessible deposits, coupled with other factors such as increasing demand due to population expansion and standard of living rise, has made development of upgrading techniques attractive to producers. Various investigations being carried out by the U.S. Bureau of Mines are described. Factors making the development of improved methods for upgrading clays attractive to producers include: depletion of accessible deposits of high-grade clays, rising transportation and labor costs, more exacting specifications, and increased demand resulting from an expanding population and a constantly rising standard of living. Industry recognizes the need for upgrading presently unusable materials and has cooperated with the U.S. Bureau of Mines by providing samples from submarginal deposits and by evaluating the products that USBM upgrades. Following are some examples of recent clay beneficiation work by the Bureau. FIRE CLAY BENEFICIATION At the Rolla Metallurgical Center, Rolla, Mo., the Bureau is conducting research to develop technically and economically feasible mineral-dressing methods to remove quartz, pyrite, and other impurities from submarginal fire clays. The research has been spurred by the growing shortage of high-grade bur-ley, flint, and plastic clays in the Missouri fire-clay district resulting from increased consumption and the low rate of discovery of new deposits of adequate quality. There apparently is ample tonnage of submarginal flint and plastic clays to maintain the industry for many years if such material can be upgraded to commercial quality. Samples have been submitted to USBM by several major producers of refractories, including A. P. Green Fire Brick Co.; Harbison-Walker Refractories Co.; Mexico Refractories Div., Kaiser Aluminum and Chemical Corp.; and Wellsville Fire Brick Co. Research on some samples has been completed and still is in progress on others. The Bureau has found that specimens containing quartz or pyrite in grains coarser than the accompanying clay generally can be upgraded either with a gravity table or hydraulic cyclone. The improvement in quality is notable not only in chemical analysis but in an increase in pyrometric cone equivalent (PCE) of one or more cones. As an example, consider the results attained on a sandy flint—a fine-grained mixture of kaolin and halloysite with quartz and minor quantities of iron and manganese oxides. Chemical analysis was: 35.4 pct alumina (A12O3) and 47.8 pct silica (SiO2). The sample contained 9.2 pct free silica as quartz. The PCE was 33. The sample was crushed to -10-mesh, blunged with water, and then stage-ground to -48-mesh. The ground sample was tabled to yield a clay fraction containing 37.6 pct A12O3, and 45.3 pct SiO2 of which 2.4 pct was free silica. The PCE was 34. Recovery of alumina by this process was 73.6 pct. Concentration of the same clay in the hydraulic cyclone was even more effective in respect to quartz removal. The clay fraction analyzed 38.6 pct A12O3, 45.0 pct SiO2 of which 0.5 pct was free silica as quartz, and had a PCE of 34. Recovery of alumina was 71.9 pct. The hydraulic cyclone was also effective in reducing the pyrite content of a plastic clay which likewise was a mixture of kaolin and halloysite, plus some pyrite, quartz, and carbonaceous material. It analyzed 30.6 pct Al2O3, 52.3 pct SiO2, 2.3 pct Fe2O3, and 0.76 pct S. The sample was blunged and screened through 10-mesh to remove some coarse pyrite, then ground to -65-mesh and cycloned to remove most of the remainder. The final product recovered 81.8 pct of the alumina at a grade of 32.3 pct A12O3, 50.9 pct SiO2, 1.4 pct Fe2O3, and 0.1 pct S. The PCE was 32-1/2, compared with a PCE of 31-1/2 for the crude clay. The fine beneficiated clays, of course, must be pelletized and dried or fired to meet commercial acceptance. This operation has already been solved by industry. Little progress has been made on two remaining problems. One is that of fine-grained impurities, not separable by table or cyclone. Flotation is being investigated to solve this. Although fine pyrite is readily rejected, a satisfactory quartz-clay separation has not been attained. The second problem, a stubborn one, is that of alkali. Samples containing as much as 5 pct potas-

Jan 1, 1961

By G. F. Jr. Butterworth

THE metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to produce in the stock a physical condition having the requisite properties. The first group consists 'of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat-treated by giving it a quench and a draw. These barrels will be referred to as "heat-treated" barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent. of manganese, show a single very pronounced point between 1300° and 1350° F. (704° and 732° C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure discussed below, Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure, shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under- a low magnification appears

Jan 7, 1919

By C. N. Garman

Homestake-New Mexico Partners operate a 750-tpd carbonate leach uranium concentrate mill near Grants, N.M. The highly mineralized water available as process water leaves much to be desired. The 628 ppm as CaCO 3 makes the use of raw water very troublesome in pipes and on filter cloths. However, the residual sodium carbonate in the final filter cake going to tails makes an ideal softening agent. To take advantage of this fact, all makeup water used in the mill is first used as tailing slurry dilution water and comes to the mill from the tailings pond. The 5-acre tailings pond serves as a thickener and 100 to 150 gpm of nearly clear solution is decanted to a pump to be returned to the mill. Since this tailings water has small quantities of uranium in the solution an ion exchange scavenger unit was installed to remove as much uranium as possible. The ion exchange raffinate is then used as final filter wash ahead of the tailings slurrying step. In spite of the large settling area this return water is not clean enough for ion exchange feed. The solids present are very fine and composed of approximately 15 pct (by weight) burnable carbonaceous material common to the sandstone uranium ores in the area, 40 pct SiOz plus 45 pct CaC03. Laboratory work showed that this material responds very well to flotation. Before deciding to use flotation, various clarifying systems such as pressure leaf filters, sand filters, and continuous vacuum pre-coat filters, were considered. Each of these could have solved the problem but with much more operating labor, more reagents and greater installation costs than the flotation step. About 100 to 150 gpm of fouled water is fed to two 66-in. Fagergren cells, in series. Reagents used at the beginning were Arquad 2HT75 and Arquad C50, at the rate of about 1% lb per 8-hr shift, or about 0.0053 lb each per ton of ore. This did not completely remove the solids but does an acceptable job. Approximately 75 pct of the slimes are a size that can be caught on a 41-Whatman Paper are removed. Removal of these slimes also allows much better settling of the coarse nonfloatable material. Advantage is also taken of this fact in a small settling tank ahead of precipitation. Removal of this amount of the slimes makes the ion t:xchange feasible. PREGNANT SOLUTION CIRCUIT The carbonate? leach-caustic precipitation method of uranium concertration does not provide for any process purification step ahead of precipitation. Therefore, any fine solids getting into the pregnant solution through the filter cloth show up in the final concentrate. This, of course, lowers the grade, and, at times, the slimy nature of these very fine solids rendered final filtration of the concentrate difficult if not impossible At Homestake-New Mexico Partners a 75-ft thickener was available for gravity clarification of 100 to 120 gpm of this pregnant solution. However this did not sufficiently remove the slimes. Laboratory investigation of the whole range of flocculants that were suggested by literature, salesmen, and friends failed to turn up anything of consequence. A continuous vacuum pre-coat filter would do the job and was investigated. The capital cost and the operating labor and materials made this a last chance choice. Following work done in the metallurgical laboratory on the tailings return water, it was found that some changes in the reagent strengths and combinations made a very definite decrease in the solids in the pregnant solution. Concentrate grade improved about 5 pct anti the final product after drying had an appreciably greater bulk density. Compared to a cost of about 2.2e per ton for pre-coat filter opelation for cleaning just one circuit, flotation costs less than 1.0 per ton of ore for cleaning two circuits. While a pre-coat filter would do a more thorough job, the flotation does all that is required for either circuit. Gravity causes the froth produced to run back into the leach circuit. This does not appear to result in a build-up of objectionable slime. No extra manpower is required; the operators in the separate areas can observe the operation of the cells and mix the small quantities of reagents as needed. Normally the 66-in. Fagergren cell requires 15 hp per cell, but this very dilute slurry needs only 10 hp for both cells. Originally, a combination of the two Arquads mentioned previously served as frothers and promoters. As further testing

Jan 1, 1962

By H. D. Colson, Robert A. Rapp

When a binary alloy is oxidized to form simultaneously an internal oxidation zone and an external scale which grows at a constant rate, the oxidation should reach a condition of steady shale, in which the internal oxidation zone is maintained at a time-independent thickness. Assuming an ideal model for the steady-state oxidation, the diffusion equation is solved for the steudy-state concentration profiles for oxygen and alloying- element in the metal. A theoretical prediction of' the steady-state thickness of the internal oxidation zone is made in terms of the experimental parameters. FOR the oxidation of binary alloys, Rhines, Johnson, and Anderson,1 as well as Mask: have derived equations describing the kinetics for the simultaneous formation of an internal oxidation zone and an external scale which was assumed to mow according to a parabolic rate law. Experimental determinations of internal oxidation zone thicknesses beneath a Cu2O scale for Cu-Be and Cu-A1 alloys3,4 have shown some deviation from Maak's theoretical expressions, because the ideal model assumed for the calculation is not met experimentally. Some pure metals, such as columbium and tantalum oxidize at elevated temperatures and high oxygen pressures to form nonprotec-tive external scales which thicken at a constant rate. If such a base metal is alloyed with a solute element which may form a more stable oxide than the solvent oxide, then internal oxidation of solute may occur beneath the growing external scale. A review of the internal oxidation of alloys has been published recently.5 The purpose of this paper is to analyze theoretically for a binary alloy the kinetics for the simultaneous formation of an internal oxidation zone and an external scale which grows at a constant rate. Consider an alloy A-B in which A is the more-noble solvent and B is the less-noble solute. The solute oxide is assumed to precipitate in internal oxidation as stoichiometric particles of BO, which are assumed to have a negligible solubility product in the A matrix. It is further assumed that the diffusion of oxygen through the zone of internal oxidation is not impeded by previously precipitated BO, particles. The specimen is assumed to be sufficiently thick so that the solute content in the center of the specimen does not change. For consistency: the following notation of Maak2 has been used:

Jan 1, 1967

By Noel Cunningham

Many excellent descriptions of the mills of the Porcupine district have been written, but no discussion exclusively devoted to the metallurgical technology has been given. These notes are intended to cover this feature briefly. They are based upon 21/2 years' mill operation in the district—i.e., practically since the beginning of metallurgical operations. Character of the Porcupine Ore.—There is no oxidized ore in the district, the surface having been deeply planed by glacial action in recent geologic time. The precious-metal content is about in the proportion of 85 of gold to 15 of silver by weight; hence, the silver is practically negligible. There are two classes of Porcupine ore, having very different characteristics; these will be referred to throughout this paper as Class A and Class B. Class A ore is a pure quartz with inclusions of schist. Generally it is heavily fractured and breaks down readily to sharp, hard grains, about minus 10 plus 20 mesh, requiring further comminution to release the gold. It carries very little pyrite; the gold is entirely free and apt to be coarse, but often spongy, going into solution readily on that account. This gold is 60 per cent. to 85 per cent. free milling, depending on the grade of ore. Class B ore is an iron silicate schist, strongly laminated, carrying 4 to 5 per cent. pyrite; its specific gravity is 2.8 to 3.0, depending upon the amount of mineralization. In breaking the ore in the mine, generally over 25 per cent. of material through a 1/2-in. ring is made; the ore readily breaks down in milling and makes a comparatively large amount of non-crystalline slime; owing to its high specific gravity, however, it is quick settling. In my opinion, the gold in this ore is free, but so finely divided that it will neither pan nor amalgamate; it appears to be disseminated through the rock and not chiefly associated with the pyrite. Veins of Class A ore occur with or without side walls of Class B, and veins of Class B occur unassociated with Class A; more often the veins are closely banded, Class A and Class B alternating, generally with Class B in excess. Both classes of ore are more or less blocky at times, and with reference to Class B this is indicative of low gold content.

Jan 1, 1915

By Jorge Munoz Reyes

There are three main oil areas in Bolivia (Fig. 1) although so far only one has yielded petroleum in commercial quantities. The Sub-Andean zone is along the easternmost ranges of the Andes, bordering the large eastern and northeastern lowlands. It extends from the Peruvian frontier, north of Lake Titicaca in a southeasterly direction towards the city of Santa Cruz and from there southward to the Argentine border. This zone forms a belt about 1200 km. long by 100 km. wide, and comprises a series of parallel, very rugged, low ranges. Oil has been known and utilized by the natives in these regions since colonial times, from the large number of seepages, which in modern times have led to the discovery of many fields. The second oil zone of Bolivia lies along the eastern and southern borders of Lake Titicaca, on the Andean high plateau, at an average altitude of 13,000 ft. above sea level. It comprises an area of approximately one million hectares (2,470,000 acres). Several seepages are known here, but little development has taken place, because of the difficulties encountered, as the greater part of the territory is covered by volcanic tuffs and ashes, which conceal the structure underneath. The third area is called the "Central zone," and is in the heart of the country, in the Department of Cochabamba, covering approximately five million hectares (12,350,000 acres). This area consists mainly of broad valleys flanked by low rolling ranges. Natural seepages are not known to exist, but there are secondary evidences of the presence of oil. The outcropping rocks are mainly Paleozoic (Silurian and Devonian sandstones and shales). Albertite and other forms of polymerized petroleum have been found in this region. Of these three main oil areas, only the first one is at present productive on a small commercial scale. This zone, developed almost exclusively by the Standard Oil Co. of Bolivia, a subsidiary of the Standard Oil Co. of New Jersey, is divided from south to north into the following local fields: 1. Bermejo (On the Argentine border) 3. Sanandita 5. Camatindi 2. San Telmo 4. Caigua 6. Machareti

Jan 1, 1935

By Best W. N.

Discussion of the paper of W. N. BEST, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1527 to 1537. WILLIAM A. WILLIAMS, San Francisco, Cal.-I would like to ask whether .Mr. Best ever had any experience with an oil burner that used neither air nor steam? W. N. BEST, New York, N. Y.-Yes. This type is commonly known as the "mechanical spray burner" and uses oil heated under high pressure to above its vaporizing point. These burners are not as efficient as the atomizing type for the following reasons: 1. They produce a round flame which; as with any other type of burner, must pass over a flat surface. A round flame cannot fit a flat surface. 2. They do not evenly distribute the heat, resulting in localized heat. 3. The outlet through which the fuel passes is very small; so all gravities of oil, especially oil containing sand, cannot be burned. 4. Their construction is such that they must be cleaned frequently, as the residuum in the fuel clogs the burner. 5. The oil opening being small, the capacity of each burner is small, so that many burners must be used in a boiler or furnace. (The fewer burners there are, the more accurately they can be regulated.) In marine boilers, these burners are largely used, because they do not require either steam or air for atomization. However, there are other methods by which this objection to other types can be eliminated, such as by the use of a rotary blower and steam turbine engine, the exhaust front the engine passing into the engine condenser, thus obviating loss of water. Mechanical burners are rarely used in shops. I know of but one power plant using them. With mechanical burners, the fuel must be maintained at a high pressure. On board naval vessels, some mechanical burners demand an oil pressure of from 100 to 6001b. It is advisable to reduce the pressure as much as possible, as fractured pipes or fittings are particularly dangerous, for the heated oil escapes as a vapor. In such cases there is liability of an explosion caused by spontaneous combustion.

Jan 12, 1915