Search Documents

By R. G. Garlick, H. B. Probst

Tungsten single-crystal specimens of various orientations were deformed in tension at room temperature. Slip traces indicated both (112)(111) and (110) (111) slip; however, about 10 pct plastic dejormation was required bejore these traces could he seen. Resolzled shear-stress considerations indicated that at least some of the particular systems observed were not those on which slip initiated hut were secondary systems. This is highly probable, considering the high plastic strains involved. Analysis of the stress data with respect to possible slip systems indicated that slip must have been initiated at stresses below the proportional-limit stresses measured. ALTHOUGH there is general agreement that slip deformation in fcc and hep metals takes place on the plane of close packing and in the direction of close packing, there is no such agreement for slip in bcc metals. It is generally agreed that the close-packed direction (111) is the slip direction, but investigations have led to conflicting descriptions of the slip plane. As Hoke and Maddin1 point out, there are essentially four points of view. 1) Deformation in bcc metals is composite shear on (112) and (110) planes or on nonparallel (110) planes, and any apparent slip on other planes can be accounted for completely by slip on these planes. Chen and Maddin have reported this to be the possible case for molybdenum." 2) Slip occurs in the (111) direction and is limited to {110), {112), and (123) planes (the three closest packed planes of the lattice). 3) Slip occurs in a (111) direction, but not necessarily on planes of close packing (banal slip). 4) Slip occurs in those directions and on those planes for which ß, the ratio of Burgers vector to interplanar spacing, is a minimum. The slip systems of the bcc metal tungsten have never been fully determined, although several investigators have reported pertinent results.3"7 The present work was initiated to determine the active slip systems in tungsten at room temperature, the critical resolved shear stresses associ- ated with these systems, and the orientation dependency of operative systems. These features of tungsten deformation at room temperature have never been reported in the literature. The authors find this somewhat surprising, particularly in view of the availability of tungsten single crystals since the advent of electron-beam zone-melting techniques and the widespread interest in refractory metals. It would seem apparent that such work has been attempted but the results have not been reported, possibly due to the conflict with deformation theory. The results of the present work conflict with any straightforward description of deformation based on the proposed explanations of slip in bcc metals. Although these conflicts have not been resolved, a presentation of the problem seems in order and should be of value to others working in this field. MATERIALS AND PROCEDURE Single-crystal tungsten rods of 1/8-in. diameter were grown from undoped commercial rod by one-pass electron-beam zone melting in apparatus previously described by witzke.8 Representative analyses of the rod before and after melting are given in Table I. There was no detectable zoning of impurities during melting. Buttonhead tensile specimens, as shown in Fig. 1, were machined from single crystals. Two flats 90 deg apart were ground in the gage length of each specimen. These flat surfaces facilitated the analysis of slip traces. No attempt was made to position these flats with respect to the crystal orientation. The worked surface layer of the machined specimens was removed by electrolytic polishing in a NaOH solution. Tensile-axis orientations were determined by standard Laue back-reflection techniques. The sharpness of the Laue spots indicated that the crystals were free of strain.

Jan 1, 1964

By P. K. Weimer

Coinpletely integrated thin-film circuits inco?,porating more than 1000 active and passive elements have been fabricated reproducibly in the laboratory by evaporation of- all components. A 180-stage modified shift register comprising 540 CdSe TFT's, 360 resistovs, and 180 capacitors was deposited upon a glass substrate during one pump-down of the vacuum systeitl. Experimental units have been operated for more than 5000 hr at temperatures uP to 85°C without failure of any slages. The present pupper reviews the charvactevistics of evaporated thin-film transistors (TFT's) and discusses their application to integrnted circuils. INTEGRATED circuits most widely used today are based upon silicon technology, with the circuits formed on the surface of a block of single-crystal silicon1 or on a block of sapphire 2,3 upon which a thin layer of silicon has been deposited. Transistor patterns and interconnections are defined by photographic procedures using photoresist masking. Large groups of transistors are produced in batches which undergo many processing steps, some of which are carried out at elevated temperatures. Passive elements are formed by treatment of the semiconductor surface or are deposited by evaporation alongside the active elements. The size and complexity of the circuits are limited by defects in the devices and by the size of the available single-crystal chips. Capacitative coupling to the semiconducting substrate may also limit useful size and frequency response of the circuits. An alternative approach to integrated circuits is based upon the deposition by evaporation of all circuit components upon a noncrystalline, insulating substrate such as glass.4 Thin-film field-effect transistors,1'6 known as TFT's, can be deposited in large arrays on glass or plastic substrates at the same time the associated passive elements are being deposited. Although still in the research stage the all-evaporated approach is expected to offer certain advantages for many applications. In particular, the use of thin films upon a noncrystalline substrate offers the prospect of producing complex, large-area circuits not now feasible with single-crystal silicon. Important applications of this type include memory arrays for computers and imaging devices for television. The ease with which the evaporated TFT's can be deposited may permit continuous, automated production methods not possible with high-temperature batch processing. Recent advances7'8 in the fabrication of thin-film transistors have led to greatly improved reproduci-bility and life of the TFT's. Experimental circuits having over 1000 active and passive elements deposited upon a common glass substrate are currently being produced in the laboratory. The present paper reviews recent progress in the development of the TFT and in its application to integrated circuits. I) DESCRIPTION OF THE THIN-FILM FIELD-EFFECT TRANSISTOR The TFT is a field-effect transistor of the type having the control gate separated from the semiconductor by a thin insulating spacer. Although its operation resembles that of the silicon MOS transistorg its construction is based entirely on thin-film techniques. Fig. 1 shows a cross-sectional view of an evaporated TFT deposited upon a glass substrate compared with a silicon MOS transistor deposited upon single-crystal sapphire.3 The semiconductor in the TFT is a poly crystal line layer, of a material which can be readily evaporated, such as cadmium sulfide, cadmium selenide,l0 or tellurium." Silicon monoxide layers have usually served as the gate insulator, but other oxides, sulfides, and fluorides may be used. Film thicknesses range from a few hundred to a few thousand angstroms. The source, drain, and gate electrodes in the TFT are of metal. Qpical source-drain gap dimensions are 0.0003 x 0.030 in., with a gate strip whose width slightly overlaps the source and drain. The source and drain electrodes should make low impedance contacts to the semiconductor. With cadmium sulfide films, gold is a satisfactory material for underlying electrodes, while aluminum is preferable for overlying electrodes.12 Considerable variation in design of the TFT is permissible, with the electrodes being

Jan 1, 1967

By R. W. Heckel, R. A. Tanzilli

Treatment of the finite, diffusion-controlled, two-phase, moving-interface homogenization problem has been carried out by numerical methods for a wide range of input parameters. Solutions have been obtained for planar, cylindrical, and spherical diffusion geometries. The effects of parameters such as the interdiffusion coefficients (concentration-independent) of- both phases, the concentrations (time-independent) of each phase at the interlace, mean composition, initial size of the dissolving- phase, and initial composition of- the two phases are considered. The results are displayed to show both the position of the interjace and the degree of homogenization (expressed in terms of concentration at the matrix phase symmetry boundary) as a function of diffusion time. Typical exaw~ples to which the results may be applied are discussed. A limited number of exact, closed-form solutions to the multiphase, diffusion-controlled, moving-interface problem exists in the literature, e.g., Refs. 1 to 7. The exact, closed-form solutions generally consider the outermost phases to be infinite in extent and also assume an interfacial velocity function. It is through use of such boundary conditions that closed-form solutions are readily obtained. An extensive literature also exists on numerical solutions to the mathematically analogous solidification problem, e.g., Refs. 8 to 12. In addition, a numerical solution involving mass transfer with spherical interfaces and infinite boundaries has recently been carried out.13 A practically important class of diffusion problems exists, however, in which the boundaries of each phase away from the interface are finite. For example the finite boundary condition arises when one sets up a model for analyzing the homogenization behavior of two-component powder compacts in two-phase systems or for studying the solution behavior of precipitates. Although exact, closed-form solutions have as yet not been found to this class of problems, solutions are possible using numerical methods. The purpose of this paper is twofold: 1) to describe a numerical method for treating the two-phase, diffusion-controlled, moving-interface problem involving finite boundaries with planar, cylindrical, and spherical interfaces; 2) to present the results of a parametric study which identifies the role played by each variable appearing in the analytical model. R. A. TANZlLLI,Student MemberAIME,onleaveofabsence from the General Electric Co., Re-entry Systems Department and A. W. HECKEL, Member AIME, are Graduate Student in Materials Engineering, and Professor, Department of Metallurgical Engineering, respectively, Drexel Institute of Technology, Philadelphia, Pa. Manuscript submitted May 6. 1968. IMD MATHEMATICAL MODEL The three geometries analyzed are shown in Fig. 1. For each configuration a symmetry element is shown, across whose boundaries the mass transfer is zero. Mean composition, C, and the characteristic solute-rich phase half-thickness (or radius), 1/2, are the independent variables while the characteristic symmetry element half-thickness, L/2 (measured from solute-rich phase center to the matrix phase plane of zero mass transfer), is a dependent variable. The symmetry element for a planar interface accurately represents a real diffusion situation involving the stacking of symmetry elements of constant size. Because cylindrical and spherical symmetry elements of constant size cannot be stacked to fill space, the meaning of the dimension, L/2, for these situations may be considered in terms of the following approximations: and where NA is the number of parallel cylindrical elements per unit area on a surface normal to the cylinder axes and Nv is the number of spherical elements per unit volume. The model consists of a solute-rich phase matrix phase composite of limited mutual solubility. The concentrations at the interface are assumed constant with time; no assumption of local equilibrium at the interface is necessary except for the case where the

Jan 1, 1969

By A. N. Crownover, H. T. Kennedy, E. P. Miesch, C. H. Bowman

The paper presents correlations of (l) molar volume of gaseous hydrocarbon mixtures with pressure, temperature, composition and properties of the C,-plus fraction; (2) shrinkage of oils during flash and differential liberation of gas, including the calculation of formation volume factor under various conditions; and (3) bubble-point pressure with temperature, composition and characteristics of C, plus. The data on which the correlations are based comprise 1,615 measurements on 900 hydrocarbon systems, including numerous systems containing nitrogen, hydrogen sul-fide and carbon dioxide. In each correlation, the number of data points covered and the accuracy is substantially greater than in previously available work. Thus, the equation yielding molar volumes of gases has an average deviation of 2.04 per cent, applied to mixtures having temperatures up to 313F and pressures up to 9,800 psis, compared to 2.37 per cent for the Benedict-Webb-Rubin equation applied to the same data, and 4.53 per cent for the method based on the law of corresponding states. he equations resented are all explicit in the dependent variable, and require no iteration on the digital cow puter. INTRODUCTION The ease and accuracy of determining the composition of hydrocarbon mixtures, compared to the difficulty of measuring their properties under reservoir conditions, makes it desirable to utilize composition as the key to physical behavior to the greatest possible extent. As a result, there are available correlations between composition, or easily measured characteristics dependent on composition, and practically every important engineering property of reservoir fluids. The task confronting us is one of finding more exact relationships between important variables rather than extending correlations to new properties. This paper describes new correlations of molar volumes of gases, formation volume factors, and bubble-point pressures with composition, temperature and where possible, pressure. Each correlation is obtained by employing a sufficiently large amount of data so the calculated properties are probably as least as accurate as the measurement on which they are based. MOLAR VOLUME OF GASES Although many equations of state have been proposed for pure gases, only a few methods are applicable to hydrocarbons at conditions comparable to those in petroleum reservoirs. Still fewer arc useful in describing the behavior of mixtures, with which the petroleum engineer is largely concerned. The correlation presented here involves procedures similar to those of Alani and Kennedy The van der Waals equation is modified to make a and b functions of temperature instead of being constants for each material.This is a cubic equation, which may have either one or three real roots. The lowest root corresponds to liquid volume, while the highest applies to gas. When the procedure was applied to 703 pressure-temperature points of 164 gases of known composition and volume, the average deviation was 12.08 per cent, and the standard deviation 8.15. The above calculations were made using the constants derived for liquids by Alani and Kennedy and the mixture equation developed by them. A closer approximation to measured molar volumes is obtained by employing different sets of constants for different areas on the pressure-temperature chart, and by changing the relationship between a,,, and b,,, for mixtures and the a, and b, for individual hydrocarbons. The various sets are shown in Table 1, and the areas for which they are recommended are plotted in Figs. 1 through 7. In these figures, the area designated by zero is in the critical region for pure materials, and the values obtained for them may be unreliable. For normal mixtures, however, the area may be added to any of the bounding areas without substantial error. The new relationships employed are

Jan 1, 1966

By R. W. Heckel, H. W. Paxton

The growth of grain boundary films and Widmanstiitten plates of proeutectoid cementite in hypereutectoid steels ulas considered quantitatively in three plain carbon steels and one "pure" iron-carbon alloy. Growth was found to take place at a slower rate than would be predicted on the basis of a model invoking rate control by long range diffusion of carbon. The films in the pure alloy grew faster than those in the plain carbon steels. A possible explanation is suggested. In 1904, Nernsst' and Brunner2 postulated that ionic crystals growing in supersaturated aqueous solutions grew at rates determined by diffusion through the solution to the growing crystal interface. The gradient down which the diffusion took place was assumed to be fixed by the supersaturated bulk solution concentration, the concentration dt the crystal surface and some arbitrary distance. The flux of material to the crystal was described as Flux where D is the diffusion coefficient, A the crystal surface area, Ci the bulk solution concentration, Co the saturated solution concentration, and 6 the thickness of the diffusion zone. It is obvious that the expression is an adaptation of F+ick's3 first law of diffusion (steady state). This was the initial formulation of what will be defined here as "diffusion controlled growth," i.e., growth limited by the long range diffusion of a component either to or from the advancing interface assuming both phases at the interface to be in equilibrium. This idea of equilibrium interface concentration implies an infinite reaction rate at the interface. Volmer, Zener,' and 11schner6 have derived expressions for the diffusion controlled growth of spherical precipitates in metallic systems. These analyses agree that the growth in a given direction should be parabolic with time. Brown and Hawkes7 observed that graphite, formed both from the decomposition of cementite and from the decomposition of eutectoid austenite in cast irons, grew according to a parabolic relationship and, therefore, concluded that the laws of diffusion controlled growth, as defined above, were obeyed. They, among others, failed to consider, however, that parabolic growth is a necessary, but not sufficient, condition for diffusion controlled growth. Mehl and Dube"' have pointed out that equilibrium may not be realized because the concentration at the interface cannot change instantaneously from that of the bulk to the saturation value. Furthermore, they propose that an equilibrium solute concentration in the parent phase adjacent to the precipitate would remove the thermodynamic activity gradient across the interface and, thus, stop the growth process. Frisch" has also emphasized the importance of interface concentrations that vary throughout the growth of a new phase. The variation in activity across an interface, as discussed by Onol' and Cahn and Hilliard,12 is of fundamental importance to this question. Ham13 considered the data of Turnbull14 on the growth of barium sulfate in aqueous solutions. He concluded that the data could be analyzed in terms of a radiation-type boundary condition. Flux across interface = K (c, - C,) [21 where C, is the concentration in the solution at the interface, Co the saturated solution concentration, and K the proportionality constant. The edgewise growth of Widmanstlitten plates, frequently referred to as the rate of lengthening, was first considered by Zener.'' Basing a mathematical analysis on steady-state (constant velocity) growth he concluded that where G is the growth rate, D the solute diffusivity, Ci the concentration in the bulk, Co the equilibrium interface concentration, C, the concentration in the precipitate, a a constant, Y the radius of curvature of the edge of the plate, and rC the critical radius, i.e., the radius which would increase the activity of solute at the interface at equilibrium under the influence of capillarity to that of the bulk. Zener1'

Jan 1, 1961

By C. E. Birchenall, H. M. Schadel

THE purpose of this study was to measure the vapor pressure of silver as the first step in the determination of activities in silver alloys and to test the limitations of the method adopted. In order to work at low pressures, below 2x10-2 mm of mercury, the orifice effusion technique was employed. To shorten the time of collection of silver from the atomic beam, radioactive silver (Ag110) was used as a tracer. The rate of effusion of a monatomic vapor from an "ideal" orifice, where the thickness of the orifice edge is negligible compared with the orifice diameter, can be readily calculated from the kinetic theory of gases, G = vM a p/v2pRT where G is the weight of material effusing from the orifice per unit time; p is the vapor pressure at oven temperature, T; R is the gas constant; M is the molecular weight of the vapor; and a is the orifice area. Consolidating constants and expressing as the weight of material effusing from the orifice in a period of time, t, (5.83)(10-2) (vM) (a) (t) (p)/vT where GT is total weight of monatomic vapor effused (g); M is molecular weight of the effusing tracer vapor; a is orifice area (cm2); t is time of effusion (sec); p is vapor pressure of effusing material (mm of Hg); and T is oven temperature (OK). The vapor effuses from the orifice in a hemispherical pattern, and the intensity of the beam in any direction is given by the cosine distribution law.' Considering this, the weight of effused material can be calculated from the amount of material passing through a circular collimator intersecting the beam. If such a collimator is in a plane parallel to the plane of the orifice and with center on the normal to the orifice center, GT = G?/1-cos2? = G?/sin2? where G? is the weight of effused material passing through the collimator, and 0 is one half the apex angle of the cone defined by the collimator circumference and the orifice center. Reducing eq 3 to the more directly measurable quantities of orifice to collimator distance, d, and collimator diameter, D, the expression becomes,

Jan 1, 1951

By Charles Austin

IN a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000° C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallo-graphic characteristics. The data, which related specifically to temper-ing temperatures of 550°, 650° and 710° C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemi-cal composition. 2. The temperature of maximum softening spread over a range from about 650° C. to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at sub-eutectoid temperatures. 4. The mode of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hr. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Determination of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000° and 850° C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938

By W. H. Bassett

IN the commercial annealing of cartridge brass there are four points regarding which definite data are essential. They have to do with the correct interpretation of grain count in its relation to annealing temperature and, incidentally, to Brinell hardness. These points are: 1. The comparison of the grain sizes of two cartridge-brass mixtures: 69 copper, 31 zinc, 0.376-in. (9.5-min.) gage; and 68 copper, 32 zinc, 0.130-in. (3.3-mm.) gage. 2. The comparison of the grain sizes of annealed metal that had previously been reduced by rolling varying amounts; for instance, 20.0, 36.6, 50.9, and 59.1 per cent. 3. The determination of standards for grain sizes on annealed brass of the composition 68 per cent. copper, 32 per cent. zinc and 69 copper, 31 zinc. 4. The comparison of grain size with Brinell hardness on identical samples of annealed metal. In their comprehensive and thorough investigation of the recrystallization of cold-worked alpha brass on annealing,1 Mathewson and Phillips have discussed the relations between temperature of anneal, degree of deformation, and structural alteration in alpha brass. They have also shown certain comparisons between the ordinary physical properties and the grain size of annealed brass. The purpose of the present investigation is mainly concerned with the grain size of cartridge brass, its relation to Brinell hardness, and the publication of sufficient data to enable those engaged in the inspection of such material to have a correct foundation upon which to work.

Jan 1, 1919

By Malcolm J. McPherson

INTRODUCTION The use of computers to assist the mine ventilation engineer began to grow in the early 1950s when electrical analogue devices were developed for the analysis of mine airflow systems in Europe and the United States (l,2,3). The need for quantitative planning of airflows in mines had become pressing and analogue computers fulfilled a useful purpose for over a decade. From about 1964 onwards, digital computer programs for mine ventilation network analysis became available (4,5) and, superseding the analogues, spread rapidly throughout the major mining countries. The successful implementations of such programs resulted in further research being directed towards the development of simulation programs to model the quality as well as the quantity of air flowing through underground workings. It is no understatement that digital computers have revolutionised environmental planning techniques in modern mining industries. This paper discusses the complex interaction of natural and mining factors which governs environmental hazards in underground mines and further indicates some of the simulation techniques which have entered practical usage or are at an advanced stage of development. THE PROBLEM OF ANALYSING THE MINE ENVIRONMENT The traditional methods of approaching environmental problems underground were based largely on empirical or intuitive techniques. The reason for this lay in the intricate relationships which exist between the many variables that influence the mine environment - and which limit the use of purely analytical methods to the simplest of cases. In order to illustrate the need for simulation techniques, Table 1 shows the three most widespread mine environmental hazards

Jan 1, 1977

By B. S. Norris, Charles R. Austin

IN a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000° C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallographic characteristics. The data, which related specifically to tempering temperatures of 550°, 650° and 710° C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemical composition. 2. The temperature of maximum softening spread over a range from about 650° C. to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at subeutectoid temperatures. 4. The node of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hr. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Determination of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000° and 850° C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938

By M. L. Samuels

In a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000' C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallo-graphic charaeteristics. The data, which related specifically to tempering temperatures of 550°, 650" and 710" C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemical composition. 2. The temperature of maximum softening spread over a range from about 650" C, to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at sub-eutectoid temperatures. 4. The mode of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hi. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Deterrnirlation of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000" and 850" C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938

By M. L. Samuels

In a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000' C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallo-graphic charaeteristics. The data, which related specifically to tempering temperatures of 550°, 650" and 710" C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemical composition. 2. The temperature of maximum softening spread over a range from about 650" C, to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at sub-eutectoid temperatures. 4. The mode of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hi. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Deterrnirlation of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000" and 850" C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938

By Joseph Chalmers, E. L. Rawlins, D. B. Taliaferro

PRoblems dealing with the movement or migration of fluids through porous beds have been the subject of much research. The subject is not peculiar to the production of oil and gas, as many investigators have studied the nature of this movement and its relationship to the problems of other industries. Darcyl conducted a series of experiments relating to the percolation of water through filter beds. King2 carried on an extensive series of laboratory experiments with the object of formulating some conception of the rate of movement of water through soils and sand strata in the drainage of surface water into underground channels and subsequent recovery of this water through wells drilled into the source beds for irrigation purposes. Slichter3 undertook a study of the same problem from a mathematical standpoint, and more recently Furnas4 has investigated the flow of gases through beds of broken solids with particular reference to blast-furnace operation. With specific reference to gas production, Muskat and Botset5 of the Gulf Research Laboratory undertook an experimental study to establish quantitatively the characteristics of and laws governing the flow of gases through consolidated and unconsolidated porous materials of fine texture with a view of predicting the performance of gas in an underground reservoir. There seems to be a general agreement that many of the relationships between the numerousfactors influencing the flow of fluids through porous materials are far too complicated to be attacked by analytical methods based upon a knowledge of hydrodynamics. For gases, the laws of

Jan 1, 1932

By Ben L. Seegmiller

Introduction The profitability of an open pit operation depends to a large extent on the use of the steepest pit slopes possible, provided they do not fail during the life of the mine Optimum pit slopes can be designed by using rock mechanics technology. Such technology includes gathering and analyzing pertinent data prior to pit design, rigorous application of rock mechanics principles during the design process, remedial actions to improve slope stability, and monitoring slopes during the life of the mine. Ignoring rock mechanics technology in pit design may place the entire mining enter- prise in jeopardy Disruption of mining operations and safety hazards caused by slope instability can be severe. A classic case in point is the major slope failure (Seegmiller, 1972) that occurred at a southwestern US copper mining operation in 1970-1971 Minor slope stability problems initially amounted to no more than a nuisance, but in time, the unstable zones became larger, causing greater disruption of production and threatening safety Mining at or near the slide toe had continued throughout the period of slope failure, aggravating the already unstable condition The original plan for this pit called for mining the overall pit slope to 37.5" Mine operators were forced to lessen the back- slope angle in the hope that the failing rock mass would stabilize. However, stabilization did not take place, and when mining in the area of failure was completed, the overall slope had been reduced to approximately 27" Mining had been successful in removing only a small portion of the ore body at a high stripping ratio.

Jan 1, 1979

By Joseph Chalmers

PROBLEMS dealing with the movement or ,migration of fluids through porous beds have been the subject of much research. The subject is not peculiar to the production of oil and gas, as many investigators have studied the nature of this movement and its relationship to the problems of other industries. Darcy1 conducted a series of experiments relating to the percolation of water through filter beds. King2 carried on an extensive series of laboratory experiments with the object of formulating some conception of the rate of movement of water through soils and sand strata in the drainage of surface water into underground channels and subsequent recovery of this water through wells drilled into the source beds for irrigation purposes. Slichter3 undertook a study. of the same problem from a mathematical standpoint, and more recently Furnas4 has investigated the flow of gases through beds of broken solids with particular reference to blast-furnace operation. With specific reference to gas production, Muskat and Botset5 of the Gulf Research Laboratory undertook an experimental study to establish quantitatively the characteristics of and laws governing the flow of gases through consolidated and unconsolidated porous materials of fine texture with a view of predicting the performance of gas in an underground reservoir. There seems to be a general agreement that many of the relationships between the numerous factors influencing the flow of fluids through porous materials are far too complicated to be attacked by analytical methods based upon a knowledge of hydrodynamics. For gases, the laws of

Jan 1, 1932

By E. T. Dumble

In the Bosquejo Geoldgico de Mexico, published in 1897 by the Secretaria de Fomento as Nos. 4, 5 and 6 of the Boletin del Institute Geologico de Mexico, the Director, Jose C. Aguilera, after a detailed account of the geological observations made by himself and his assistants on their several trips through the various districts of the Republic, gives in Part 2 a synopsis of the geology of Mexico, describing . al1 the formations recognized, the rocks comprised in them, their geographical distribution, disturbances, principal eruptions and economic features, as explanatory of the Geological Map of Mexico. In Part 3 Prof. Ordonez describes many of the interesting eruptive rocks of Mexico." This work brings together in a very satisfactory way about all of the published results of geological investigations in Mexico; and although the determinations of the authors with reference to some of the sedimentary deposits are very different from those of other writers, they seem to be based upon good paleontological grounds in each instance. From the map and the text of this paper it appears that the condition of knowledge in regard to the geology of the State of Sonora, at the time of its publication, was about as follows: The western portion of the State, lying between the coast line of the Gulf of California and the foot-hills of the Sierra Madre mountains, is largely Quaternary, interrupted by areas of Azoic rocks and of later eruptives, with two or three limited exposures of limestones of the Cretaceous; while the eastern or

Jan 1, 1900

By Eric Jette

THE results of an investigation of the ternary system iron-chromium-ilicon were reported in 1936 by the present authors.1 Partly for the sake of theoretical interest, and partly because of the possible commercial importance of these alloys, the present investigation was undertaken to determine the effect of some of the commoner elements likely to occur, deliberately or otherwise, in such alloys if made on a commercial scale. The elements thus added were carbon, nickel or manganese. The alloys studied were, therefore, parts of quaternary systems. This investigation was concerned primarily with the effect of these additional elements on .the alpha-iron phase and the boundary between this phase region and the alpha plus sigma two-phase region. The sigma phase is a ternary solid solution based upon the compound FeCr. The work was performed mainly by X-ray methods, but a number of microscopic examinations were also made and are reported. While isolated alloys in the composition ranges studied may have been discussed in metallurgical publications, no systematic investigation of any assistance to us was found. Of the earlier work, the investigations on the iron-chromium-carbon system and on the chromium carbides by Westgren and his coworkers,2,3 enabled us to identify the carbide phase. Several articles appeared after the present experimental work had been completed. Lucas and Wintrup4 determined the solubility of carbon ill molten iron-chromium-silicon alloys. Tofaute and his coworkers5,6 have made detailed studies of the iron-chromium-carbon system, which will he referred to later.

Jan 1, 1937

By George Espey, George Sachs, G. B. Kasik

IT has been reported frequently that the hardness and strength vary over the cross section of cold-worked, particularly cold-drawn, material. Brass rod and wire usually have been found to possess a maximum strength and hardness near the surface.1,2 According to Sachs,' the center fiber has about the same strength as a wire stretched by the same amount in a tensile-test machine, the strength increasing toward the surface (Fig. I). These differences are particularly large for wire given a small reduction on drawing through a die with a wide opening. However, with increasing reduction and hardness, a tendency to form a thin soft surface skin becomes apparent. On the contrary, copper wire has usually been found to possess a soft surface skin3-5 and it has been reported by Harris3 that during the cold-drawing of hot-rolled wire the surface layer becomes increasingly softer than the core, while the layer of maximum strength moves toward the core, it being found near the surface at first. The increase of strength and hardness from the core to the skin is readily explained by the observation that, in addition to the stretching, the layers of a rod or wire are sheared more the closer they are to the surface.1,6-8 However, the presence of a soft surface layer can be attributed only to an annealing effect. The source of such a softening might be the extremely high temperature that originates from the friction between

Jan 1, 1942

By G. B. Kasik, George Sachs, George Espey

IT has been reported frequently that the hardness and strength vary over the cross section of cold-worked, particularly cold-drawn, material. Brass rod and wire usually have been found to possess a maximum strength and hardness near the surface.1,2 According to Sachs,' the center fiber has about the same strength as a wire stretched by the same amount in a tensile-test machine, the strength increasing toward the surface (Fig. I). These differences are particularly large for wire given a small reduction on drawing through a die with a wide opening. However, with increasing reduction and hardness, a tendency to form a thin soft surface skin becomes apparent. On the contrary, copper wire has usually been found to possess a soft surface skin3-5 and it has been reported by Harris3 that during the cold-drawing of hot-rolled wire the surface layer becomes increasingly softer than the core, while the layer of maximum strength moves toward the core, it being found near the surface at first. The increase of strength and hardness from the core to the skin is readily explained by the observation that, in addition to the stretching, the layers of a rod or wire are sheared more the closer they are to the surface.1,6-8 However, the presence of a soft surface layer can be attributed only to an annealing effect. The source of such a softening might be the extremely high temperature that originates from the friction between

Jan 1, 1942

By Ralph Hultgren

Few phase diagrams of alloys composed of two transition metals have been adequately studied, probably because of the high melting points involved. Transition metals are the elements that have inner shells incompletely filled with electrons. They comprise groups lIIa to VIIIa of the periodic table, including more than half of all metals. We have chosen to study two systems whose comparatively low melting points allowed the alloys to be melted in a molybdenum resistance furnace. The nickel-palladium system proved to consist of a simple series of solid solutions, but iron-palladium manifested several remarkable features. The main characteristics of the latter diagram were decisively established, but lack of time prevented precise determination of phase boundaries. The gamma to alpha transformation in this system is unusual and warrants further study. Grigorjewl determined the liquidus and solidus of the iron-palladium system by thermal methods. He found a minimum melting point, but no eutectic. He also found that palladium lowered the gamma to alpha and raised the gamma to delta transformation temperatures of iron, with a complete series of solid solutions existing between gamma iron and palladium. His measurements also indicated a compound or quptbr-lattice near the composition FePda. Jellinghausz found that annealing at 500" C. greatly increased 111 magnetic coercive force of an alloy of composition FePd. X-ray diffraction photographs showed that a tetragonal ordered phase had formed during the anneal. Hocart and Fallot made magnetic measurements over the entire range of composition. They found that less than 5 atomic per cent Pd

Jan 1, 1939