Search Documents

By L. W. Reynolds, R. F. Campbell, K. G. Carroll, S. H. Ballard

Based on metallographic and X-ray data probable equilibrium conditions from 1340" to 2400°F are presented for the composition range investigated. These are correlated with investigations of Takei and Kuo. Provision is made for existence of Mo, C and (Fe, Mo)2,C, carbides heretofore omitted in diagrams in this composition range. These carbides and (Fe, Mo),C, in equilibrium with ferrite and austenite, restrict the austenite and austenite + ferrite fields to lower carbon contents and higher temperatures than in the Fe-C system. OK groups of steel of different molybdenum content, but with approximately the same carbon variation in each group, Table I, were studied. The alloys were melted in an acid-lined 30-lb high-frequency induction furnace, and the ingots forged to l-in. rounds, which were then ground to 0.75-in. diam. To minimize chemical segregations a short length of each bar was given a high-temperature heat treatment as listed in Table I. Specimens 0.062 to 0.125-in. thick were thereafter cut from the homogenized bars for heat treatment to determine phase changes in the alloy. Heat treatments were performed in either a lead bath or muffle-type electric furnace, depending upon the temperature required. Maximum temperature variation was * 2" F in the lead bath and * 5"F up to 1900°F and +8"F above 1900°F in the electric furnace. Adequate protection of the specimen from the oxidizing atmosphere in the electric furnace was obtained by sealing the specimen in either a pyrex or a silica capsule which was evacuated or not as circumstances required. For austenitizing followed by quenching to an isothermal temperature, the specimen was placed in a closed-end refractory tube the mouth of which, extending beyond the furnace, was connected to a vacuum pump. The specimen could be withdrawn from this tube and quenched as desired. IDENTIFICATION OF PHASES The principal method of identification of phases was metallographic examination conducted on surfaces well removed from exposure to lead or atmosphere effects during heat treatment. Hardness measurements (Dph/lOkg) were also made on these surfaces. The etching reagents used and their effects are listed in Table II. Martensite and ferrite were readily recognized by their customary appearance after etching with saturated picral or 1 pct nital. The presence of liquid at high temperature was indicated by curved interfaces characteristic of boundaries between solid and melt, by intergranular pools of dendritic areas in a carbide matrix, and by a black network coincident with austenite grain boundaries. Examples of these structures are shown in Figs. l(a) and (0). The types of carbide which were attacked by the electrolytic chromic acid etch and the alkaline KMnO, etch, Table 11, were identified by X-ray analyses of extracted carbides of five alloys. Carbide residue was obtained from a metallographic specimen by etching the specimen for 24 hr in hydrochloric-picric acid in alcohol (grain-size reagent), after which the carbides, standing in relief, were scraped from the surface of the specimen and mounted on a glass slide. Diffraction patterns were obtained with a Philips spectrometer using iron-filtered cobalt radiation. Figs. 2, 3, 4, and 5 illustrate typical etching behaviors with chromic acid and alkaline KMnO,. Chromic acid attacked Mo,C as shown in Figs. 2(a) and (b)-but not (Fe, Mo),C, Fig. 3(b). Alkaline KMnO, attacked (Fe, Mo),C, Fig. 3(c), and also attacked M0,C. In accordance with these behaviors, a typical differentiation of coexisting Mo,C and (Fe, Mo),~ is shown in Figs. 4(a) and (b). The carbide (Fe, Mo),,C, could not be obtained free of other coexisting carbides for etching experiments. The behavior. however. of coexisting carbides identified by x-ray diffraction as Mo,C ind (Fe, Mo),,C, indicate that (Fe, Mo)23C6 is not etched by chromic

Jan 1, 1961

By M. N. Pathasarathi, P. A. Beck, T. J. Koppenaal

EARLIER work1 indicated that in rolled and annealed copper the volume fraction of the cube-texture component may increase on continued isothermal annealing. Merlini found2 that in rolled copper the well-known increase in the amount of cube-oriented material with increasing annealing temperature3 is concurrent with grain growth, which takes place after recrystallization is complete. It was found that both in copper2 and in aluminum4 the texture resulting from primary recrystallization, even if this is followed by some grain growth, may in general comprise, in addition to the cube-texture component, four symmetrical texture components of the general type (123)[412], i.e., components not very far from the ideal orientations of the rolling texture. The volume fraction of the cube-texture component increases on further annealing at the expense of these four components.' The present work was undertaken to study quantitatively the increase in the volume fraction of the cube-texture component in the course of normal grain growth, under varying conditions. Since the grain-gr3wth behavior of A1-Mn alloys has been already investigated in some detaiL5 an A1 + 0.8 pct Mn alloy was chosen for this work, in which the extent of normal grain growth can be effectively controlled by the inhibiting effect of a dispersed second phase. EXPERIMENTAL PROCEDURE High-purity aluminum of the following composition was used: A1 99.997 pct, Cu 0.0004 pct, Fe 0.0005 pct, and Si 0.001 pct. A high-purity A1-Mn master alloy was prepared by dehydrating manganese chloride at 500°C and reacting it with molten high-purity aluminum at 750°C in a graphite crucible.5 The Mn metal reduced from the salt by the molten aluminum goes into solution in the latter. The master alloy? containing 13 pct Mn, was solidified under conditions suitable for minimizing segregation. An ingot of the final alloy, to be used in the experiments, was per pared by melting high-purity aluminum and the necessary amount of master alloy in a graphite crucible, and by pouring the molten alloy into a graphite mold preheated to 700°C through a box containing graphite baffles designed to intercept most of the aluminum oxide films floating in the melt. The melt was then solidified by placing the mold on a water-cooled copper plate and by keeping the top of the mold hot, in order to minimize piping. The 6 1/2 in. long, 11/4-in.diam ingot consisted largely of a single crystal. Chemical analysis showed that there was little segregation from the bottom (0.83 pct Mn) to the top (0.81 pct Mn). Spectrographic analysis of the ingot showed that the impurity content remained essentially the same as that of the aluminum used. The ingot was processed so as to obtain a uniformly small grain size. without banding. The ini-tial steps of rolling in the form of a flat bar and of annealing, down through a thickness of 0.4 in., are shown in Table I. At this point the bar was cut into four sections, each approximately 3 in. long, which were processed separately as shown in Table If. The table also gives the penultimate grain sizes obtained in each section by annealing prior to the final rolling of 90 pct RA. During the final rolling the strips were reversed end to end between passes. Annealing treatments were given in a salt pot furnace, with the temperature controlled to 1°C. All annealing of section "6s" was carried out above the solvus point to avoid the formation of second-phase precipitate. The penultimate annealing was sufficiently short to give a relatively fine grain size in spite of the high temperature. Section "6L" was processed in a similar manner, except that the penultimate annealing was much longer, so as to allow considerable grain growth. Section "4" was given the two final

Jan 1, 1961

By H. R. Hose

The total crude fluorspar reserves in Western Europe, including the USSR and the Soviet sphere, Thetotalare estimated to exceed 17 million metric tons. The total fluorspar production in 1951 in Western Europe, excluding the USSR and Soviet sphere, amounted to 371,109 metric tons. The chief fluorspar-producing countries in Europe, excluding Russia and the Soviet sphere, are France, Western Germany, Italy, Spain, and the United Kingdom. TOTAL crude fluorspar reserves in western Europe, containing more than 35 pct CaF2, are estimated at 12 million metric tons, while reserves in the USSR and Soviet sphere may exceed 5 million metric tons. The bulk of these reserves are concentrated in the USSR, Spain, United Kingdom, Western Germany, and Italy. Since published estimates of the tonnages of individual mines and explored deposits are not available for most countries in Europe, the estimates given in Table I for individual countries are necessarily approximate, as they have been compiled from various sources and modified and combined according to the author's judgment. The majority of fluorspar deposits in Europe belong to the late Paleozoic metallogenetic epochs and have been found within or along the borders of the Hercynian massifs. Deposits in the Central and Esterel massifs of France, those of Western and Eastern Germany, Sardinia, the Catalonian coastal range and the Sierra de los Santos in Spain, and those of Devonshire and Cornwall belong to the Hercynian metallogenetic epochs. The deposits in southern Norway and Sweden belong to the middle Paleozoic or later, those of northern England to the late Paleozoic or later, those of northern Spain and Greece to the late Mesozoic, and those of northern and probably central Italy and Switzerland to the early Tertiary. Fluorspar occurs typically in veins, lenses, and stringers, but also in bedded replacement deposits and pockets, and may be colorless to white, yellow, green, pink, brown, blue, or purple to almost black. Except for the colorless variety, the only kind which can be used for the optical industry, the color of the fluorspar does not affect its ultimate use. Crystalline cubic or octahedral fluorite of CaF2 composition, with 48.9 pct fluorine and 51.1 pct calcium, has a specific gravity of 3.18. The ore in place, however, usually averages 3.0 metric tons per cubic meter owing to the quantity of other minerals asso- ciated with the fluorspar in the veins and the physical state of the fluorspar, which may vary from sugary to massive crystalline or microscopic inter-growths with barite or quartz. Barite of 4.5 sp gr, quartz of 2.66 sp gr, and chert and calcite are commonly associated with fluorspar. Other minerals usually present in lesser amounts are celestite, wad, silver, lead, zinc, copper, iron, and uranium minerals. In some cavity fillings the rhythmic deposition of the fluorspar, barite, and quartz into successive crusts may make it possible to handpick the crude ore on belts or to separate the fluorspar from other minerals while the actual mining is carried on. Where metallurgical grade lump spar is required for foundries, separation of quartz and barite may be made also by jigs and heavy media, and in some mines the lead and zinc sulphides may be separated and recovered by vibrating tables. However, except in the case of unusually high grade deposits, acid grade fluorspar is obtained by flotation. By this process fluorspar deposits grading down to 35 pct CaF2 in the crude ore can be worked at a profit when fluorspar, lead, zinc, and silver prices are high, as the sulphides of these ores can be separated from the fluorspar by flotation and concentrated.

Jan 1, 1956

Through the courtesy of Mr. J. H. Batcheller, we are able to give the following extracts from a letter written by Mr. Caetani: It has been a nice idea of yours to collect for me all those scraps of news I received a few days ago and to send me such a long interesting letter. In four years war I have had practically no news. Burch wrote several times but several of his letters were lost and so mine. I believe I even wrote to you. Much has changed since our last days in Telluride; here and there many have disappeared. Of myself I will tell you in a few words: for a year I was in Cadore(?), where I had the good luck to do to the others what they wished to do to me, and had good luck on my side. Then I went to Macedonia for 5 months, did little fighting but lost my faithful fellow officer and companion.

Jan 6, 1919

By David S. Butts

There are many solution mining operations that use solar ponds as a mineral recovery step. Other locations in the world are now under investigation to recover minerals by solution mining but require the cheap energy of solar ponds to make the recovery viable. This paper shows a step-by-step material balance system that can be used in both simple and complex solar ponds. Use of this system will help the engineer determine if solar ponding efficiency can be improved or if solar ponding will work at all with a given set of conditions. Even the most complicated solar pond can be reduced to six flow streams. These are (1) feed, (2) exit, (3) leakage, (4) entrainment, (5) salts, and (6) evaporation. The equations developed in this paper will allow the solar pond engineer to easily evaluate the effect of each of the flow streams on the mineral production of a pond or pond complex.

Jan 1, 1985

By C. N. Reid

Slip-line studies on deformed chromium single cvystals showed the usual bcc behavior. At room temperatuve, cross slip was prevalent—slip was not confined to a given plane, but the slip direction was (111). At -10O0K, slip occuvred on (110) planes, twins on(112) planes, and cleavage on (1001 planes. A single-crystal tensile specimen with an axis close to [011] showed a pronounced yield drop and high strain rate sensitivity which zclere used to derive relevant parame tevs in a dislocation dynamics treatment. Transmission electron microscope studies confirmed the existence of (110) slip planes and showed ecidence of loops punched out by precipitates and of grown-in dislocations promoting tangling. OF recent years experimental studies have been made of the deformation characteristics of single-crystal molybdenum and tungsten, but very little has been published on the behavior of single-crystal chromium. During a study of the mechanical properties of chromium, single-crystal studies were made which have already been partially described.&apos; However, additional information was generated which was not directly relevant to the main theme of Ref. 1, and, therefore, was not reported. In view of the need for complete documentation of deformation modes, the experimental observations made on the deformation of single-crystal chromium are summarized here, together with an electron-microscope study of the associated dislocation structures. It was found that, in terms of the deformation modes, chromium is a conventional bcc metal, showing a very pronounced yield-point phenomenon. Further, it was found that the flow strength of these crystals is very sensitive to the strain rate. Finally, the crystals were observed to contain many unidentified precipitates, which often were associated with prismatic dislocation loops. EXPERIMENTAL METHODS Single crystals were grown from rods of wrought chromium by the method of zone annealing. Rods of "1/4in.-diam were supported vertically in an argon atmosphere while an induction coil was moved up the rod at 1 in. per hr. The power was adjusted to just below that required for melting, and the process produced single crystals in about 30 pct of the rods used. The orientations of the crystals, in general, lay near [011] and are summarized in Fig. 1. Before this treatment, the wrought material contained 35 pprn C, 68 ppm O, and 12 ppm N.* An analyzed single crystal *Usual metallic impurities found in iodide chromium are: Al, 5 ppm; Ca, A ppm; Cu, 2 ppm; Fe, 75 ppm; Yg, 0.5 ppm; Yn, < 3 ppm; Mo, < 3 ppm; Ni, 4 ppm; Si, < 20 ppm; Ti, < 1 ppm; V, 4 ppm; Zr, < 3 ppm. contained 10 pprn C, 79 ppm O, and 50 pprn N. Tension and compression specimens were shaped from the crystals by mechanical grinding, followed by the electrolytic removal of about 0.010 in. from the surface in a perchloric/acetic acid bath. All specimens had a gage length of 0.75 in., and tension specimens had a diameter of 0.100 in., while that of the compression samples was 0.200 in. Mechanical tests were carried out at a rate of 1.3 pct per min, and temperatures below 0°C were attained by means of a nitrogen cryostat similar to that of Wessel.2 EXPERIMENTAL RESULTS Modes of Deformation. In addition to the tensile properties of these crystals, which are described in Ref. 1, deformation markings on the surface were studied. Crystals A and F, Fig. 1, were deformed in tension at 300°K to 10 and 16 pct strain, respectively. The surfaces contained visible slip lines, about 1 C( apart, composed of both straight and wavy segments. They did not define a single plane, and so determination of the slip plane was not possible. However, the slip direction was deduced by comparing the axial orientations of the crystals before and after deformation. Fig. 2 is representative, and shows that the axis ro-

Jan 1, 1968

By W. C. Lilliendahl, G. Meister

Uranium metal with a purity of about 99.9 pct was produced on a large scale by fused salt electrolysis with a material efficiency of about 90 pct. The material efficiency depends mainly on bath composition, electrolysis temperature, electrode smothering, and elutriation during washing of the powder. RESEARCH and development work on fused salt electrolysis carried on by the Westinghouse Lamp Div. Bloomfield, N. J., was done under the Manhattan District Corps of Engineers and later under the Atomic Energy Commission for the commercialization of uranium production for the first atomic pile at the University of Chicago in 1942. From the conception of the atomic bomb project it was recognized that metals with impurity levels having little metallurgical significance would be required. Permissible impurity levels were based on neutron absorption. Of particular significance was boron, which could not be present in amounts exceeding 1 ppm. The electrolytic method as developed in 1930 by Driggs and Lilliendahl,1,2 and later improved, yielded uranium of very low boron and other deleterious impurity content. No other method was capable at that time of producing uranium metal of the required purity.&apos; The low boron content of uranium produced by the electrolytic process resulted from the availability of the reactants which were low in boron content, and from the inherent elimination of boron in the fused salt bath. Since the heart of any electrolytic process is the electrolysis cell, this paper will deal with the development of the original bath composition for the efficient production of uranium from a batch process to one of continuous operation. Emphasis also will be placed on other factors which will affect the material efficiency of the process. With the laboratory cell the material efficiency of uranium powder recovery in the early electrolysis was relatively low, about 35 pct based on the ratio of uranium recovered to uranium added. This early process also had other defects. The electro- lytic bath could not be used continuously. After three runs from a freshly charged crucible, the deposit showed a tendency to slip off the electrode as it was raised from the bath. This condition necessitated pouring the charge every fourth run and preparing a new bath. It was assumed at that time that this condition was caused by the increasing fluoride concentration with each addition of uranium salt, which adected the mobility of the uranium ions. Experimental The electrolysis cells differed in size only. They were of the floating cathode type. The laboratory cells were 21/2 in. ID and 6 in. deep and operated at 30 amp and 5 volts. Production was about 150 g metal powder per 8 hr. The plant cells (5 units) were 9 in. ID x 21 in. deep and operated at 1800 amp at 12 volts. The total production unit was designed to produce 250 lb of uranium powder per 8 hr day. Because of the tendency of uranium fines toward spontaneous combustion, material efficiencies were based only on the recovery of useful coarser metal which could be safely handled. The reported efficiencies are of particular significance only as related to the same group of experimental procedures. At the start of the project no changes were contemplated until previous data could be definitely confirmed. Therefore, the first experiments were with the 50 pct CaCl2-50 pct NaCl mixture. The material efficiency of uranium deposition as a function of the number of electrolyses is shown in Table I. In Table I, the decrease in efficiency at 800°C with number of runs is apparent and confirmed the earlier data. Operating at 900°C enabled the number of runs to be doubled, but before pouring the charge the efficiency of recovery became poor. This test indicated that the improved efficiency might have been caused by an increase in the fluidity of the bath.

Jan 1, 1958

By A. D. McMaster, M. L. Gimpl, N. Fuschillo

There is interest in the use of rhenium metal films as resistive elements in thin-film circcits, and already some zvork has been done using er)aporated rhenium films. It has been found that rheniim films protected from the atmosphere by an evaporated layer of silicon monoxide show excellent electrical stability. Unprotected films, however, are subject to aging- effects, notably the increase in electrical resistivity as a function of time. This phenomenon can be understood as primarily one of oxidation of the thin films. This paper is concerned with the study of the oxidation and crystallization behavior of such unprotected films. It has been found that the oxidation rates are a function of the substrate temperatures used during the deposition of Lhe metal films. The strictures observed in the films are correlated with the film resistivities and some data are presented to establish the existence of the various types of oxides of rhenium. ThERE is some interest in the use of thin films of rhenium metal as resistive elements in monolithic, thin-film integrated circuits. Some work has been done using evaporated films and it has been found that such films, if protected from the atmosphere by an evaporated layer of silicon monoxide, show excellent electrical stability up to temperatures of 500"." Rhenium films unprotected from the atmosphere tend to age and the electrical resistivity of the films increases as a function of time. Rhenium films, of the order of <100A thick, prepared by electron-beam evaporation techniques are found to oxidize very readily when exposed to dry air at room temperature. It would seem, therefore, that this aging phenomenon could be attributed to the oxidation of the metal films. In this investigation, the oxidation and crystallization behavior of thin films of rhenium evaporated onto silicon monoxide substrates were studied as a function of the substrate temperatures used during the evaporation. The films were examined using electron-microscopy and electron-diffraction techniques. EXPERIMENTAL RESULTS Rhenium metal was evaporated onto suitable prepared substrates which were heated to various temperatures. The evaporations were performed in a vacuum of approximately 5 x 1CT5 torr. The evaporation was carried out at a rate of approximately 10A per omin. The final film thickness was approximately lOOA and the resistance ranged from 5000 to 10,000 ohms per square. The substrates used for supporting the metal films were made by evaporating 75A of silicon monoxide onto freshly cleaved mica. The silicon monoxide film was then floated off the mica by immersing the composite in water. The film could then be picked up on a clean nickel grid. Silicon monoxide substrates were chosen because of their similarity to quartz and glass substrates commonly used for making thin-film resistors. Fuschillo, Gimpl, and McMas-ter have also shown that silicon monoxide films have only minor structural changes at temperatures up to 800°C. This fact simplified the interpretation of any changes observed in the electron micrographs or electron-diffraction patterns obtained from the deposited rhenium films. After the evaporations were completed, the substrates were cooled to room temperature, except where noted differently, before the coated substrates were removed from the vacuum system. All aging of the deposited films was done in a desiccator. The evaporated films were examined in an electron microscope equipped with a hot stage that would permit continuous observations of the samples up to temperatures of 1000°C. RESULTS A series of electron micrographs of the rhenium films deposited on the silicon monoxide substrates are shown to Figs. 1 to 3. In all cases, the metal films are approximately 100A thick and the micrographs were taken 1 hr after the deposition was completed. here was no apparent structure in the films deposited on the substrates held at the higher temperatures. The

Jan 1, 1967

By William P. Blake

Postscript to the paper read by Prof. William P. Blake at the Lake Superior meeting, September, 1904. POSTSCRIPT.*-Since the publication of my paper upon the blackening of the surface of rocks in desert regions, I have noted that similar views of the origin of superficial discoloration in the case of certain rocks from the Salt Lake basin of Utah have been expressed by Prof. George P. Merrill. In the pamphlet, he described the brown-coated weathered boulders from Tooele county, reaching the conclusion that the discoloration was due to the solution of the manganese and iron compounds &apos;in the interior of the boulder, while they were in the water, and the gradual bringing of this material to the surface through capillarity and its oxidation when exposed.

Mar 1, 1905

FIGURES covering appropriations recommended by the Budget Bureau for the Bureau of Mines at Washington for next year are now available and are as quoted below. APPROPRIATION BUDGET APPROPRIATION 1928 1929 General Expenses $ 86,000` $ 86,000 Investigating Mine Accidents 386,470 399,470 Mining Investigations in Alaska.. 10,860 10,860 Operating Mine Rescue Cars and Stations 327,630 342,630 Testing Fuel 154,000 158,500 Mineral Mining Investigations.... 99,570 125,000 Oil, Gas and Oil-Shale Investiga- tions 198,260 198,260 Oil-Shale Investigations 5,000 80,000 Expenses Mining Experiment Sta- tions 173,000 173,000 Care, etc., Buildings and Grounds, Pittsburgh, Pa 71,360 76,360 Maintenance and Operation, Fuel Yards Balance Balance Helium Investigations :.... 75,000 75,000 Helium Production and Conserva- tion 1,063,000 462.000 Potash Investigations 100,000 100,000 Economics of Mineral Industries. . 225,000 275,000 Totals $2,975,150 $2,562,080

Jan 1, 1928

By T. M. Chatard, Cabell Whitehead

The Republic mine, situated forty miles from Marcus, a station on the Spokane Falls and Northern Railroad, in the northeastern part of the State of Washington, was located in 1896, but no development-work was dolie until the spring of 1897. While much of the ore mined since then has been rich enough for shipment to smelters, a method of locally treating the lower-grade ores soon became a matter of prime importance, because only about 40 per cent. of the values could be recovered by plain amalgamation, even with ores assaying 4 to 5 ounces of gold per ton. Experiments with cyanidation, in various ways, led to the adoption of the Pelatan-Clerici process and the erection on this system of a 10-ton experimental plant, which was later increased to a capacity of 35 tons per day. The extractions by this process showed much improvement over previous work, especially when the ore was crushed to

Jan 1, 1901

By Henry Leidheiser, Melvin C. Jr. Hobson

The rate of formation of the intermetallic compound, indium antimonide, at the interface between iudium and antimony at 100°C is greatly increased when a composite electrode of indium electrode -posited on antimony is made the cathode in an electrolytic cell. The amount of indium antimonide formed during electrolytic treatment at constant potential appeared to he proportional to the square root of time, but the scatter of the data, particularly at long times, makes it impossible to state this conclzlsi1:ely. The rate constant for the electrochemical synthesis was estimated to he 1.5 x 10-12 sq cm per sec. A similar- set of experiments was conducted in the absence of an applied potential but under otherwise similar conditions. The rate constant lor the thermal synthesis was less than 2 x 10-14 sq cm per, sec, at least two orders of magnitude less than obtained during electrolytic treatment. In a series of electrochemical studies it was observed that intermetallic compounds formed on the surface of polarized electrodes.1&apos;2 The possibility of using this technique for the electrochemical preparation of intermetallic compounds was investigated and subsequently applied to the synthesis of the semiconducting III-V compounds. Gallium antimonide, indium arsenide. indium antimonide, and indium bismuthide were successfully formed by electrodepositing the Group III element from a boiling acid solution onto an electrode made of the Group V element. The following kinetic studies were undertaken on indium antimonide to obtain quantitative information on the rate of formation of this representative III-V compound under a potential gradient. EXPERIMENTAL The electrolytic cell for these experiments was a modified, three-neck, round-bottom, 500-ml distillation flask. Sealed into the side of the flask was a Luggin probe which monitored the surface of the working electrode and extended out of the flask to a small reservoir containing a saturated calomel electrode. The counter electrode was platinum. The three electrodes were connected to a Wenking po-tentiostat which maintained a preselected constant potential near the surface of the working electrode with reference to a saturated calomel electrode. All potentials noted in this paper are with reference to a saturated calomel electrode at 45° ± 5°C. The potential and the current were both monitored using Sargent Model MR recorders. The antimony electrodes were cast in graphite molds to form spheres about 15 mm in diameter with a shank 6 mm in diameter and 10 mm long. A heavy copper wire (12B & S gage) was soldered to this shank. Collodion was applied for protection to the shank and the connecting part of the copper lead. A snug-fitting O-ring was slipped over the shank and the electrode was then fitted into a teflon holder such that only the spherical portion was exposed. The electrode surfaces were cleaned and chemically polished prior to assembly and introduction into the electrolyte by etching in a modified CP-4 solution (50 parts glacial acetic acid, 10 parts concentrated nitric acid, 2 parts 48 pct hydrofluoric acid). The electrolyte was 10-2 M In+3 in 1 MH2So4 and its temperature was held constant by refluxing. The reflux condenser was open to the atmosphere and no temperature correction was made for changes in barometric pressure. The indium concentration in the electrolyte was checked from time to time by the analytical method outlined below for the determination of the amount of indium antimonide formed electrochemically. A schematic of the recorded potential is shown in Fig. 1. At point A the antimony electrode was introduced into the cell and the open-circuit potential recorded. At point B the potentiostat, preset at the desired potential, was switched on. It was switched off at point C and the potential fell to the open-circuit value of the electrodeposited indium. The

Jan 1, 1965

By C. M. Romanowitz, H. A. Sawin

PLACER dredging as we know it today, especially gold dredging, is an industry about 40 years old, dating from the beginning of this century, when a few mining men in California saw the possibilities in adapting earlier dredging methods to California placer fields in and immediately adjacent to streams. At first it was thought that dredges must be operated in existing stream beds, but experience soon pointed the way to dredging alluvial deposits of old stream beds, operating on landlocked dredging ponds. Within the first five or six years of modern dredging, experience was gained so rapidly that dredges to dig 60 ft. below water level were designed and built. This depth was believed by many operators to be the maximum at which successful dredging could be carried on. Alluvial deposits of gold, suitable for dredging, were readily handled by equipment available and developed early in the industry&apos;s history. Much of the gravel was easily dug and if deposits were cemented, contained large boulders, or for some other reason could not be handled by a dredge, the ground was abandoned in favor of other deposits that could be handled easily. Many failures, adversely affecting the dredging industry, resulted from attempts at that time to extend the scope of placer dredging with equipment not suited to the formation being dredged. Dredging ground suited to early equipment was exhausted eventually, but many supposedly undredgeable alluvial fields containing gold in commercial quantities were found and became known to dredgemen. Improved equipment was needed to work deposits known to exist at great depths or associated with unusual obstructions. Operating companies looked to dredge manufacturers and metallurgists, particularly manganese-steel foundries, for improved designs and materials. Experience developed in California has spread throughout the world, and dredges of improved types have been adapted to the mining of platinum and tin as well as gold. Space will not permit a description of all the improvements in dredging since the early days, but a few of the recent developments are worthy of note, because they make possible the dredging of placer deposits of great depth, those having hard, irregular bedrock or containing large boulders in great quantities, and compacted or cemented gravel deposits. DEEP DREDGING At Hammonton, Calif., Yuba Consolidated Gold Fields has, within the past two years, built its dredge No. 20. The company has operated continuously in that field since 1904, digging successively at maximum depths of 60 ft., 8o ft., 112 ft., and now 124 ft. below water level. The first dredges were equipped with buckets of 6 and 7 ½ -cu- ft. capacity; six dredges operating in the field today have 18-cu. ft. buckets, digging now 65 to 124 ft. below water level. Some ground near Hammonton has been dug for the third time, owing to the devel-

Jan 1, 1941

Jan 1, 1967

Jan 1, 1967

By Henry M. Howe

THIS paper gives the composition of the iron and slag at different stages in the "air-furnace" process of preparing "hard metal," or white cast-iron, for conversion into malleable cast-iron by annealing. The details of the process are given in an appendix. One of us had been trying for years to work some chemist of some of our malleable-iron works up to a degree of enthusiasm which would lead him to make such au investigation. It would have had the advantage of the greater familiarity with the conditions which one habitually on the spot must have. Failing in this, he made use of an opportunity which presented itself of taking samples here represented, with such fairness as the conditions permitted, holding firmly that a rough approximation to the truth is better than the complete lack of data, or that a bird in the hand is worth two in the bush. We hope that this attempt may stimulate others effectively to duplicate this work, and thus correct or confirm it. Our results are shown in Table I. and graphically in Figs. 1 and 2. Discussion.-At the time when the first two samples were taken, the metal and slag were still too sluggish to permit fair sampling, and not until sample 6 were the conditions really favorable, because at the time of the fourth sample the metal was not fully melted, and even at the time of sample 5 it was still sluggish. Indeed, the slag was probably very heterogeneous throughout, because it took up silica and alumina rapidly from the bottom, and because it was so siliceous as to be sluggish at this relatively low temperature. This hetero-geneousness is exaggerated in the two samples of slag 8, apparently by the great viscosity due to its extraordinary acidity. Note that the manganous oxide of one sample is about two and

Mar 1, 1909

By Cyril Wells, Robert F. Mehl

The diffusion of carbon in gamma iron plays an essential role in many metallurgical processes. In carburizing, in graphitizing, in homogenizing, in the formation of pearlite from austenite, and in other processes, migration of carbon in gamma iron occurs.1&apos;2 A full understanding of the rate at which these processes occur obviously requires a knowledge of the rate of diffusion of carbon. In carburizing, for example, the depth of carbon pentration is determined by the carbon concentration in solid solution at the surface, and by the rate of diffusion inward of the carbon. Until reliable data on the rates of diffusion of carbon are available it is unlikely that a full quantitative description of this process will be obtained. In the formation of pearlite from austenite, the segregation of carbon and alpha iron from the austenite obviously requires the diffusion of carbon; the rate at which pearlite nodules grow is evidently controlled at least in part by the rate of diffusion of carbon; it is unlikely that we shall understand the factors that determine the rate of growth unless data on rates of diffusion of carbon, and the variation of these with composition, grain size, and temperature are available. Accordingly it was decided: (1) to determine, more accurately than hitherto, the diffusion coefficients of carbon in austenite over a wide temperature and a wide concentration range, (2) to study the influence of grain size and impurities on this diffusion coefficient, and (3) to study the effect of manganese and nickel on the rate of diffusion of carbon in the austenite of manganese and nickel steels, respectively; the influence of carbon on the rate of diffusion of manganese and of nickel will be made the subject of later papers. The rate of diffusion of carbon in gamma iron has been studied by Runge3 by Tammann and Schonert4, by Bramley and co-authors,5-14 and

Jan 1, 1940

By Cyril Wells, Robert F. Mehl

The diffusion of carbon in gamma iron plays an essential role in many metallurgical processes. In carburizing, in graphitizing, in homogenizing, in the formation of pearlite from austenite, and in other processes, migration of carbon in gamma iron occurs.1&apos;2 A full understanding of the rate at which these processes occur obviously requires a knowledge of the rate of diffusion of carbon. In carburizing, for example, the depth of carbon pentration is determined by the carbon concentration in solid solution at the surface, and by the rate of diffusion inward of the carbon. Until reliable data on the rates of diffusion of carbon are available it is unlikely that a full quantitative description of this process will be obtained. In the formation of pearlite from austenite, the segregation of carbon and alpha iron from the austenite obviously requires the diffusion of carbon; the rate at which pearlite nodules grow is evidently controlled at least in part by the rate of diffusion of carbon; it is unlikely that we shall understand the factors that determine the rate of growth unless data on rates of diffusion of carbon, and the variation of these with composition, grain size, and temperature are available. Accordingly it was decided: (1) to determine, more accurately than hitherto, the diffusion coefficients of carbon in austenite over a wide temperature and a wide concentration range, (2) to study the influence of grain size and impurities on this diffusion coefficient, and (3) to study the effect of manganese and nickel on the rate of diffusion of carbon in the austenite of manganese and nickel steels, respectively; the influence of carbon on the rate of diffusion of manganese and of nickel will be made the subject of later papers. The rate of diffusion of carbon in gamma iron has been studied by Runge3 by Tammann and Schonert4, by Bramley and co-authors,5-14 and

Jan 1, 1940

By Robert Maes, Robert de Strycker

The solidifzcation reactions in the Cu-Sn-As system were determined by microscopic examination, thermal analysis, and X-ray diffraction. The system presents no ternary compound. There is a quasi-binary section, of a simple eutectic type, between the compounds Cu5As2 and SnAs; the system presents, in addition, one ternary eutectic reaction, one ternary peritectic reaction, and seven transitional reactions. The temp-peratures corresponding to each of these reactions were determined, most of them with an accuracy of *lLC. The isothermal lines of the liquidus surface were also established for almost the entire diagram. NO reference was found in the literature relative to the Cu-Sn-As phase diagram and this is believed to be the first study on this subject. The Cu-Sn diagram was taken from Hansen and Anderko;&apos; it is represented by Fig. 1, with the phase designation which will be used in the remainder of this work. For the Cu-As diagram, the solution proposed by Hansen and ~nderko&apos; must be modified to take account of recent data, principally from Heyding and Despault~ and from Hume-Rothery and Burns; this yields the diagram represented by Fig. 2. As for the Sn-As diagram, it is not established with certainty, particularly so far as concerns the solid solubility of tin in arsenic and the solidification reactions near the compound SnsAsz. For this last point, Hansen and Anderko propose two solutions: congruent melting of Sn3Asz with a eutectic SnsAsZ + SnAs or incongruent melting implying a peri-tectic reaction L + SnAs = Sn3As2. Microscopic examination of the few binary alloys prepared in this composition range made us prefer the second of these solutions, which gives the diagram shown by Fig. 3. EXPERIMENTAL METHODS The experimental techniques used in this work were microscopic observation and thermal analysis; a few X-ray diffraction patterns were taken to verify the

Jan 1, 1967

By R. V. Norris

It was stated in a former paper1 that an intensive study of anthracite costs was being made by the engineers of the United States Fuel Administration. The results of this study are now available and are offered as a supplement to the former paper. Anthracite costs as reported for the 6-months period, December, 1917, to May, 1918, inclusive, as compiled by the Federal Trade Commission, were used as a base, and charts similar to those described in the former paper were made for the standard white ash anthracite and for red ash and Lykens valley coals. Adjustments The adjustments of cost from a reported to a price-fixing basis, as described for the bituminous methods, were applied but showed only minor adjustments as necessary. The great spread in anthracite prices on the varyingsizes, which for the 6-mo. period under review ranged in average from $5.244 for nut to $2.074 for barley coal, makes the question of the percentage of sizes produced at the different collieries a vital one. The realization with the same prices for each size must be within very wide limits, when it is considered that the percentage of prepared coal reported from different collieries varied from over 80 per cent. to below 30 per cent. for fresh-mined coal. Hence, as the spread in prices for the various sizes must be predicated on some percentage, it is essential to find some method of adjustment to allow for this variation. The logical method of adjustment is to calculate actual costs to costs as of the standard percentage of sizes, so that the margin between the adjusted costs and the average realization shall be the actual margin for each colliery between its actual costs and actual realization due to its particular percentage of sizes. As a base for realization the actual percentage of sizes for fresh-mined coal for the 6-mo. period was adopted. This percentage is given in Table 1.

Jan 1, 1920