Search Documents

By J. W. Spretnak, G. W. King

THE crystallography and morphology of 0-Al,Fe precipitates in an A1 + 0.5 wt pct Fe alloy have been studied by transmission electron microscopy. The alloy was cast in cylindrical ingots, 15 cm in diameter and 60 cm in length, and cooled slowly. The measured composition was 0.527 wt pct Fe, 0.001 wt pct Mg, and 0.003 wt pct Cu. Spectrographic analysis revealed no additional trace impurities. Thin slices were cut from the ingot and reduced by more than 95 pct by rolling to a thickness of 0.1 mm with no intermediate annealing treatments. These thin sheets were then vacuum-annealed for 1 hr at 612°C and air-cooled in their capsules. Thin foils for examination in the electron microscope were prepared by electropolishing. The precipitate is found in the form of oval platelets on the (110) planes of the matrix. The major axes of the platelets are parallel to the (110) directions of the matrix, and vary in length from 1/2 to 2 p. The thickness is about 1/10 p. Examples of platelets, both in the plane of the foil and normal to the foil, are shown in Figs. l(a) and l(b), respectively. lack' found that ?-A13Fe (more correctly All13Fe4) belongs to the monoclinic system. Using Black's structural data and simultaneous electron-diffraction patterns from the matrix and precipitates, the habit planes and directions were determined to be: (00l)? || (110)Al [100]? || [001]Al The orthogonal crystallographic axes of the precipitates are accurately in the habit plane, while the measured coincidences of the directions are only within 10 deg. The major axis of the platelet is parallel to [010] in the 0. This orientation corresponds to the direction of nearest registry of the lattices.

Jan 1, 1964

By R. B. Lincoln

THE function of a pyrometer protecting tube is to maintain an atmosphere about the thermocouple most favorable to its continued accuracy and long life, and at the same time permit the weld of the couple to attain the full temperature of the area or object being measured. In addition to protecting the thermocouple from the chemical or alloying effects of the products of combustion or bath being measured, the tube must also protect the couple from mechanical injury. The conditions met in practice vary so much that no one material is suitable for all applications. The usefulness as well as the expense of maintenance of a pyrometer system are influenced greatly by a choice of the most suitable protecting tube. The tube must protect the couple without itself becoming too great an expense item. The protecting tube should have the following qualities: (1) A melting point well above the highest temperature to be encountered. (2) Sufficient strength through the entire range of temperatures to hold up its own weight and resist such shock and jar as are unavoidable. (3) It must be impervious to the atmosphere or bath to which it will be subject. (4) It must not give off any vapor injurious to the couple. (5) It must not form any oxides fusible below the highest temperature to be measured. The proper location of the tube in the furnace is almost as important as the choice of material. The tube must be placed as near to the work to be heated .as possible. It must be kept out of the direct path of flame, both because that would give too high temperature readings and because partly burned fuel will destroy the tube faster than the quiet products of combustion.

Jan 9, 1919

By F. H. Deily, Jean M. Quets, Milton E. Wadsworth, John R. 222-000-000-012 Lewis, D. S. Rowley, R. J. Howe

Samples of synthetic magnetite were reduced in hydrogen-water vapor atmospheres in the temperature range 450o to 900oC. The reaction was always surface controlled, indicating the final products of reaction are nonfirotective. Three separate cases have been identified from the kinetic results: Case I, reduction of magnetite to iron below 570°C; Case II, reduction of magnetite to iron above 570°C; and Case 111, reduction of magnetite to wustite above 570 oC. In Cases I and 111 the kinetics have been explained by the formation of oxygen anion vacancies in the magnetite surface followed by associated diffusional processes. In Case 11 the observed kinetics have been related to the concentration of iron cation vacancies in the wustite layer formed, followed by associated steady-state diffusional processes. The concentration of cation vacancies in the wustite is maintained constant by the magnetite-wustite equilibrium. THE reduction of the oxides of iron has been a subject of study and interest for many years. However, few attempts have been made to interpret the results in terms of the mechanism of reduction of an iron oxide by either hydrogen or carbon monoxide. Stalhane and Malmberg' using CO, H2, and CO-Hz mixtures, developed the rate expression: where m = mass of oxide reduced, t = time, k = a constant, s = surface area, P = partial pressure of of CO or H,, and P, = partial pressure of the reducing gas at equilibrium. The rate of reaction per unit area was proportional to the difference between the partial pressure of the reducing gas and its pressure at equilibrium. Hansen, Bitsianes, and Joseph2 studied the reduction of pellets of hematite to magnetite with mixtures of CO-CO,. They concluded that below 450°C the reaction proceeded according to a model in which CO reacts with the hematite surface producing an oxygen ion vacancy. The rate controlling step was then assumed to be oxygen ion diffusion through vacancies resulting in the formation of magnetite. They derived an expression giving the rate of reduction proportional to the cO/CO, ratio. Recently McKewan3 published results for the reduction of magnetite spheres in atmospheres below 570°C. He explained his results by an equation of the form where K, is the equilibrium constant for wustite-iron equilibrium attributed to the formation of wustite as an intermediate in the reduction of magnetite. According to McKewan, Kp is an equilibrium constant for H, -HO adsorption in which oxygen is deposited on the surface from the H,Oand subsequently acts as a poison for reduction by hydrogen. Sample Preparation and Experiments. In this work the authors used the same apparatus and experimental procedure employed in the hydrogen reduction of magnetite. Sintered disk samples weighing approximately 1.5 g and measuring 1.2 cm in diameter and 0.25 cm in thickness were prepared by a method described previously.4 Partial pressures of hydrogen and water vapor were controlled by bubbling hydrogen through a series of flasks containing distilled and deionized water maintained at constant temperature in an oil bath. The total flow rate of the reacting gases—hydrogen and water vapor—was approximately 0.5 liter per min. The entire external system was maintained at a temperature above the oil bath to prevent condensation of water vapor. This was accomplished by wrapping electrical resistance elements over all surfaces. The glass column containing the weighing system-a McBain balance suspended from a gold chain-was enclosed in an aluminum tube heated by nichrome resistance wire enclosed in an insulating material. The temperature of the glass column was held constant by means of a series of thermocouples connected in parallel to a Leeds and Northrup temperature controller. This was necessary since variations in temperature resulted in expansion and contraction of the glass column and could be readily observed with the cathetometer. The spring extensions were measured through a window with a gaertner cathe-

Jan 1, 1962

By Charles Catlett

Some years ago the writer was struck by what might be called the remarkable vitality of the Virginia furnaces during the panic of 1893; and attention was called to the fact in the American Manufacturer of February 8,1895. From the second half of 1892, which was a period of maximum output, to the second half of 1893, when the full effects of the depression had been reached, the output of pig-iron had fallen off in Illinois 85; in New York, 66; in Ohio, 51; in Tennessee, 44; in Pennsylvania, 28; and in Virginia only 15 per cent. It seemed a reasonable inference that the State which had thus shown its marked ability to meet hard times could make and market its product with a larger margin of profit than any of the other States. This was true at that time, and to a certain extent the reasoning still holds good; but my mistake was in not fully realizing the marked effect of the Mesabi development, combined with reduced economies in transportation, and the consequent advantage to those furnaces which were so situated as to utilize these new commercial factors. The effect of these factors is seen in comparing the second half of 1894 with the second half of 1892. New York had dropped off 44, Alabama 23, Tennessee 21, Illinois 19, and Virginia 16 per cent., while Pennsylvania had increased 5 and Ohio 10 per cent. While there is no question of the great economy which has been made possible for certain interests which are peculiarly situated with reference to the ores of the Northwest, it is yet too early to say what furnaces not so fortunate will have to pay for their raw material. Already an increase of twenty cents per ton of ore has been announced, based upon increased cost of production.

Jan 1, 1900

By J. I. Drever, C. R. McKee

The push-pull test, which is a simple injection and pumping sequence of ground water spiked with solutes of interest, is presented as a method of determining the adsorption characteristics of a formation. Adsorption properties are necessary to predict restoration from both in situ coal gasification and in situ uranium extraction. The major problems in applying laboratory measurements to the field concern scaling the effect of particle size, and obtaining representative samples. Laboratory measurements are conducted on gram to kilogram scale samples, whereas the push-pull test evaluates a sample weighing approximately 130 to 1,000 metric tons, depending on volume injected and porosity. The problems in translating laboratory results to the field appear to be less severe for sedimentary uranium bodies than for coal. Laboratory measurements are useful in delineating possible ranges in adsorption properties, and in planning the field experiment. The adsorption properties of a formation are characterized by the cation exchange capacity (C) and the distribution coefficient measured at low concentration, (kd) 'Laboratory procedures for their measurement on coal and uranium ore are reported. Two field push-pull tests were conducted on uranium formations in Wyoming. Adsorption properties estimated from these tests on the basis of a simple cell model were compared to the laboratory values. In the first case, excellent agreement was observed between the values estimated from the field test and the values measured in the laboratory. In the second case, the value for kd determined in the laboratory was 5 times higher than the field value. It is recommended that push-pull tests be conducted on coal formations being considered for in situ gasification in view of the great uncertainty in extrapolating 1aboratory.adsorption properties to the field.

Jan 1, 1979

By Nicholas J. Grant, Olaf Troili, John Chipman

IN recent studies of the factors which affect the rate of desulphurization and its equilibrium, it became apparent that certain concurrent reactions were operative which had a significant effect on desulphurization. This is emphasized in the experiments of Hatch and Chipman1 and of Grant, Kalling, and Chipman' by the slow approach to a final state of equilibrium which is in marked contrast to the initial rapid transfer of sulphur from metal to slag. Since the removal of sulphur is of such profound importance in iron and steelmaking, it appeared necessary to investigate the reactions responsible for this behavior. It is now known that the presence of iron oxide in the slag interferes seriously with the principal reaction of blast-furnace desulphurization: CaO (slag) +-S + C - CaS (slag) + CO [l] The interfering reaction is most simply expressed as: CaS (slag) + 0 = CaO (slag) +-S 121 and a small concentration of oxygen (or FeO) is sufficient to hold a considerable amount of sulphur in the metal. It has been shown by Grant, Kalling, and Chipman2 that the addition of MnO to blast-furnace slag slows the removal of sulphur from the metal. This effect overshadows the contribution of MnO to basicity and is ascribed to its oxidizing power. It will be shown in this paper that SiO, also has sufficient oxidizing power to interfere with blastfurnace desulphurization. This is, of course, only one of its several effects. Primarily it is an acid and therefore reduces the concentration of excess lime. But when silicon is reduced to the metal the oxygen to which it was previously bonded becomes in part available for reaction 2. The proof of this statement is found in the following experiments. Experimental Procedure and Results Utilizing the same procedure and apparatus described by Grant, Kalling, and Chipman' five additional heats were made using slags IV and 11, the starting compositions of which were: slag IV—40 CaO, 10 MgO, 35 SiO,, 15 A1,0,; and slag 11—50 CaO, 10 MgO, 25 SiO,, 15 Al3O3. An important difference between these heats and those previously reported was that silicon to the extent of 1 to 4 pct was added to the present heats whereas the starting silicon content was formerly about 0.2 pct. Table I shows the slag and metal analyses for heats 82 to 87, and Table I1 shows the silicon addi- tions made to the charge. These additions are based on 400 g of metal and 400 g of slag. All heats had 1.65 400pct S charged before the cold slagadditions. The temperature was maintained at 1525°C. Rate of SiO, Reduction: Fig. 1 shows the silicon content of the metal in contact with slag IV at 1525°C as a function of time. Heat 70 from the work of Grant, afunctionKalling,of and Chipman is included as the lowest starting silicon. It will be noted that eeven with 4 pct Si in the starting metal, there is an increase in silicon content with time. Heat 84 is apparently approaching silicon equilibrium very slowly. Heats 70 and 82 with very much lower slowly.starting silicon show a more rapid initial rise in startingsilicon content but do not reach equilibrium during a long holding period. Fig. 2 shows 3 different initial silicon contents for Fig.2shows3differentheats 73 (from Grant, Kalling, and Chipman) 86 and 87, in contact with slag II, the most basic slag. Heat 73 is increasing in silicon with time, whereas heat 87 with an initial silicon content of 3.7 pct shows a decrease with time. Heat 86 shows a very close approach to equilibrium. The rate of transfer of silicon from slag to equilibrium.metal is very slow in all of those heats, even those which are initially far from equilibrium. ____

Jan 1, 1952

By N. L. Carwile, G. W. Geil

A metallographic study was made of deformation twinning (Neumann lamellae) in ingot iron slowly deformed in tension at —196O and —150°C. The results showed that twinning is initiated mainly during the initial stages of plastic deformation. However, the breadth of the twins generally increases with increase in strain up to fracture of the specimen. HE results of an investigation of the effect of low I temperatures on the flow, fracture, strain hardening, and strain aging characteristics, and the true stress-strain relationship for specimens of ingot iron deformed in tension were reported recently.1,2 In that study specimens of ingot iron, in different initial conditions, were slowly deformed in tension at various temperatures between —196" and +100°C. A phenomenon observed, but only briefly reported, was the formation of deformation twins (Neumann lamellae) in the specimens deformed at the lower temperatures. Preliminary metallographic examination of these specimens indicated that there was apparently some correlation between the deformation twinning and the strain of the specimen and that this factor merited further investigation. Some recent investigations have indicated a direct association of Neumann lamellae and the fracture of the metal. Bruckner".' * postulated that the twinning immediately precedes the fracture and the latter is initiated by the stopping of the propagation of twins, either at subgrain boundaries or at other structural features. Tipper and Sullivan5 postulated that Neumann lamellae are initiated by the shock or a shock wave set up at fracture in the still highly stressed unbroken metal, and that a high rate of deformation is a necessary condition for their formation. An extensive metallographic examination, therefore, was made of many of the specimens used in the study of ingot iron at this Bureau and of additional specimens deformed to selected strains under various conditions. The present paper summarizes the effects of deformation under these conditions upon the breadth and scope of the deformation twins. Other features of twinning will be discussed in another paper. Material and Testing Procedure All of the specimens were prepared from one lot of ingot iron, as hot-rolled, of chemical composition other than iron as follows: C, 0.02 pct; Mn, 0.02; P, 0.005; S, 0.018; Si, 0.002; Cu, 0.10; 0, 0.058; and N, 0.002. Cylindrical tensile specimens with a 2 in. gage length were used. The reduced section was slightly tapered from each end; the diameter (0.438 in.) at the midsection of the gage length was about 0.003 in. less than at the ends. The specimens were finished to the final dimensions by grinding and polishing in the axial direction. The ends of the specimens were machined with 3/4 in. x 10 threads and the shoulder fillets were machined to a radius of 0.75 in. The specimens were extended slowly in tension (deformation rate less than 0.5 pct reduction in area per minute) while immersed in an appropriate cryogenic liquid maintained at the desired temperature. The minimum diameter of the specimen was measured during the test by means of a specially designed reduction of area gage accurate to 0.0001 in." A detailed description of the testing equipment and the method of maintaining the desired temperature is given in a previous paper.' Each specimen, after deformation to a specified strain at a selected temperature, was sectioned longitudinally and examined metallographically. The preparation of specimens for metallographic examination was carried out in the usual manner by mechanical polishing and etching. Results and Discussion Deformation twins in specimens of ingot iron extended slowly in tension at —196" and —150°C are shown by the representative micrographs of Figs. 1

Jan 1, 1954

By Oscar Weiss

STILFONTEIN and surrounding areas gave nega-tive results in all prospecting attempts since about 1904 when Goerz and Co., a forerunner of Union Corporation Ltd., first drilled in the region and on the farm Stilfontein. Subsequent efforts by African and European Investments Co. and Anglo American Corp. from 1934-37 were completely unsuccessful. Holes drilled by these companies on the farms Riet-fontein, Hessie, and Palmietfontein were stopped in the Lower Witwatersrand system without finding payable reefs. The results of gravimeter, ground magnetometer, and aerial magnetometer surveys are presented in the area, in and around the new Stilfontein Gold Mine, in the Klerksdorp District of the Transvaal in the Union of South Africa. The gravimeter and ground magnetic surveys were completed in 1947—48. The gravity anomalies suggested a block of Upper Witwatersrand quartzites faulted-up between denser rocks of dolomite and Ventersdorp lava. Boreholes S.T. 1, 2, and 3 were drilled in 1948 and, after penetrating the dolomite and Ventersdorp lava, entered Upper Witwatersrand quartzites and intersected the Gold Estates Reef and Vaal Reef. Subsequent drilling delineated the suboutcrop of the Vaal Reef and determined the main structure of this horizon. The gold content of the Vaal Reef was highly payable and shaft sinking is now in progress. The Stilfontein Gold Mining Co. has been formed and, up to date, f5,000,000 capital has been raised for plant, shaft sinking, and development. The payable Vaal Reef horizon extends further south from Stilfontein, the reef occurring at increasing depths. It is possible that at least another mine may be established on these deeper horizons. The farm Stilfontein 39 is situated in the Klerksdorp District of the Transvaal. This farm and the surrounding areas have been subjected to repeated programs of prospecting dating back to about 1904, when Goerz and Co., the forerunner of Union Corporation, Ltd., first drilled on the farm and in the surrounding areas. From 1934-37, numerous boreholes were drilled on the neighboring farms, Riet-fontein. Hessie. and Palmietfontein, by African and European Investment Co. and Anglo American Corp. All these efforts were completely unsuccessful, and nobody suspected any possible gold-bearing area on Stilfontein until about 1947, when a gravity traverse run by B. D. Maree on the main road, showed a negative gravity anomaly. During 1947-48, the writer's organization completed gravimeter and magnetic surveys on Stilfontein and Rieffontein. An area of negative gravity anomalies was mapped, and it was suggested that this could be caused by blocks of Upper Witwatersrand quartzites, of the average density of 2.65, faulted up between dolomites and Ventersdorp lavas, the density of both of these rocks being 2.8. Fig. 1 shows the geology of the area as mapped by L. T. Nel of the Geological Survey of South Africa. The boreholes on Stilfontein, with the exception of a single hole of Goerz and Co., were drilled after the completion of the geophysical survey. The grouping of the first boreholes S.T. 1, 2, 3, 4, 5, and 6, clearly shows that these were located in the zone of negative gravity anomalies. Fig. 2 shows the gravity anomaly contours. Fig. 3 shows two sections across the gravity anomaly, together with the corresponding geological sections as obtained from boreholes. The close relation between gravity values and thickness of dolomite plus Ventersdorp lavas is striking. The two latter formations having the same density (2.8), act as one mass as far as gravity effects are concerned. Fig. 4 shows the magnetic anomalies observed on the ground by vertical magnetometers and at 500 ft abbve mean ground level by aerial magnetometer. The latter are anomalies of the total magnetic intensity. The magnetic results show that, on the farm Rietfontein and on the northern half of Stilfontein. Lower Witwatersrand magnetic shales were to be expected at relatively shallow depths. As the strongly

Jan 1, 1952

By John F. Kendrick, Paul D. Cornelius

This paper is a progress report of a study the authors are making of the sucker-rod pump, considered as a vibrating system with one degree of freedom, with forced vibrations and with viscous damping. Dr. S. Timoshenko's formula is given, defining such a system. Each factor is considered in respect to the problem of operating sucker rods, and the zone is pointed out in which the mathematics do not apply to the sucker-rod pump, because of its variable mass. This general theory is interpreted in the light of nearly two years of testing wells in the field, and correlating the results of other tests. The motion of the pumping mechanism is a vibration. The string of sucker rods vibrates with a natural frequency. The motion of the plunger is the result of adding together these two vibrations, and is modified by a damping or friction factor. The controlling factor appears to be the ratio of the period of the natural vibration of the rod string to the period of the vibration of the pump. The first conclusion is that a definite value of this ratio, which is below resonance and is probably not greater than 0.5, should not be exceeded in order to assure satisfactory performance from the sucker rods. The second conclusion is that the component parts of the pumping equipment should be selected to give the smallest practical period of the natural vibration, and when this does not permit operation at a safe speed and give the required plunger displacement, a longer polished-rod stroke should be used. While the quantitative results are but rough approximations, the qualitative analysis of pumping problems on this basis promises to be of considerable value in diagnosing the cause of poor performance and prescribing suitable remedies. The trouble that results, whenever it becomes necessary to crowd the sucker-rod pump, to take potentials or to handle increasing volumes of water, is responsible for the belief that this type of pump is not equal to present day needs, and that it is only a question of time before some other pumping device will take its place. Of the troubles experienced, it is not surprising that the frequency of sucker-rod failures should

Jan 1, 1937

By Fred Wise

THE Getchell mine, a comparatively recent gold discovery, is in the old Potosi mining district, Humboldt County, Nevada. All ore is mined from open pits using Diesel shovels and gasoline trucks. Two types of ore are mined, oxide and sulphide. Oxide ores are siliceous or shaly; sulphide ores either gougy, siliceous or shaly. In mining, the sulphide ore is segregated into hard and gougy ore, because the gouge must be dried before it can be crushed, The oxide ore is not segregated. GENERAL METALLURGY The oxide ore is the leached outcrop that overlies the sulphide ore body. All of the iron and arsenic sulphides found in the sulphide ores have been thoroughly oxi-dized, The sulphur and arsenic have been leached out while the iron is present as hematite and limonite. The oxide ore is amenable to direct cyanidation, and although no visible free gold is present it is released at a comparatively coarse grind. The sulphide ore is more refractory, since the gold is all of micron size and some of it is locked in fine sulphides. It has been established microscopically that the free gold is coated with an impervious shell, which is probably some form of iron compound. The sulphide ores contain from 1.5 to 2 per cent of arsenic, which is present as orpiment and realgar with minor amounts of arsenopyrite. The orpiment and realgar are of a later mineralization than the gold and are barren. Roasting and washing of the sulphide ore prior to cyanidation is necessary to eliminate the arsenic, to alter the gold coating from an insoluble form to a soluble form, and to release the gold associated with the fine sulphides. Washing the ground calcine in weak sulphuric acid, trona, or hot water are beneficial in the order named, but to date the water is the best from an economic standpoint. Metallurgical tests as well as plant practice indicate that a certain amount of gold cannot be recovered even by going beyond economic practices, On this basis metallurgical results are viewed in the light of an optimum tailing rather than a per-centage of extraction.

Jan 1, 1940

By H. A. Coy, James A. Noble

The Mascot mines of the American Zinc Co. of Tennessee are situated at Mascot, Tenn., 14 miles northeast of Knoxville, on the Southern Railway. The district is centrally located in the Great Valley, or Appalachian Valley Province. Prior to 1900, a small output of zinc was obtained from oxidized ore mined in open pits. In 1900, a shaft was sunk to sulfide ore, and in 1903, a second shaft was put down, neither being as deep as 200 ft. The American Zinc Co. of Tennessee began drilling in 1911, and outlined an ore-body to which its No. 1 shaft was sunk, to a depth of 365 ft. Since that time, the American Zinc Co. of Tennessee has been the only operator in the district. The Federal mining laws have never been in operation in Tennessee and mining lands are as irregular in boundary and area as farm lands. Ownerships are generally held in fee. In most cases the surface and mineral rights are transferred together. Electric power is supplied at 66,000 volts by the Tennessee Power Co., from a hydro-electric plant at Parksville, Polk County, Tenn., 100 miles from Mascot. No other power is used, but an emergency steam plant is held ready in case of interruption of service. Labor is all native and non-union. Negroes are employed for most of the shoveling, and for a few miscellaneous jobs, but for almost no other work. Exploration Exploration is carried ahead of mining largely by surface drilling. Both churn and diamond drills are used. Holes are not spotted according to geometric plan, but to block out ore outlines with the least number of holes. Churn-drill cuttings from each 5-ft. run are mounted for formation record, and in ore ground, all the bailings from each 3 ft. of advance are sampled and assayed. Diamond-drill cores are sampled and a specimen core filed for formation record. In ore ground, all the core

Jan 1, 1925

By John D. Verhoeven, Edward E. Hucke

An experimental technique has been developed for the measurement of the rate of electrotransport to a precision of 1 pct in the molten Bi-Sn system. Results are presented across the phase diagram from 30°C above the liquidus to 520°C. A phenomenological description is presented and the data on Bi-Sn are thereby converted to the effective charge, Analysis of the data indicates the true charge of the migrating tin species in bismuth to be +1.8 at 500°C. The data agree well with the recent work of Belashchmko. fieldintensity. The resistivity of the molten Bi-Sn system is also presented. WHEN an electric field is applied to a metal, a relatively large current is produced due to the ease with which electrons move within the metal. The electric field also produces a force on the ions which might cause them to migrate. Such a migration of metallic ions has been detected under certain conditions. This electromigration of the metallic ions will be referred to herein as electrotransport. The study of electrotransport in metallic systems has a rather long history dating back to the initial work of Gerardin1 in 1861. General reviews of electrotransport in liquid and solid metals have been published by Schwarz,2 Jost,3 Seith,4 and Heumann.5 In reviewing the literature it is apparent that the theoretical developments are not yet complete. The difficulty arises in describing the momentum transfer between the migrating ions and the electrons. In addition, there is a lack of good quantitative electrotransport data at high temperatures, especially in liquid metal systems. This work was undertaken to establish quantitative electrotransport data in a liquid metal system which might serve as a critical test of the theoretical developments. The Bi-Sn system was chosen for analysis, and the rate of electrotransport was determined as a function of temperature and composition. THEORETICAL CONSIDERATIONS If all of the atoms of a metal are considered to be positively charged due to the loss of electrons to the

Jan 1, 1963

By H. S. Rawdon

One of the most vital problems in the manufacture of steel at present is the occurrence of the defects that have been popularly termed "snow flakes," "flakes," or "scabs." Particularly is this the problem of many manufacturers who, during the past 2 yr., have undertaken large-scale production for the first time. A study of the microstructure of such defective material throws considerable light upon the nature of these defects and is essential before measurcs may be taken for the elimination of the defects. Flakes do not appear to be found in the plain carbon steels; they have been found. however, in abundance in some of the simple alloy steels that are being used in such vast quantities; vie., nickel steel of the approximate composition, 0.40 carbon and 3.5 per cent. nickel, and in the chrome-nickel type. The present article summarizes the characteristic features of defective steel of the flaky type as they have been found by laboratory study of numerous specimens, and it aims to show the conditions within the metal that are favorable to the occurrence of this type of defect without entering into the details of mill practice (size of ingot, design of molds, rate of cooling, distribution of cooling stresses, etc.), all of which conditions appear to play a role in the production of these defects. MacrostrUctURe To one familar with flaky steel, the appearance of "snow-flakes" is unmistakable and is not to be confused with other types of defects. Figs. 1 to 6 show the appearance of fractures of steel showing this type of defect; the white silvery area, which always has the appearance of being of a very coarsely crystalline structure, in the specimen stands out in bold contrast to the darker background and readily justifies the use of the term "snow-flakes." Fig. 1 shows the appearance of the faces of the two halves of a nickel-steel forging that has been split to show the interior flakes. Fig. 2 is a nickel-steel bar (carbon 0.40 per cent.,

Jan 1, 1920

By Alden Greninger

IN a recent study1 of the deformation of metastable beta copper-zinc and beta copper-tin crystals, it was established that the parallel markings that appear on the surface of these crystals after slight deformation represent lattice transformations. Stereographic analysis showed that in beta copper-tin, the poles of these markings deviated one or two degrees from poles of the form { 133 } . In beta copper-zinc the plane delineated by the markings corresponded to no one crystallographic plane of the matrix lattice; the marking poles deviated from 5° to 11° from poles of the form {110}, and were displaced only a few degrees from (110) zones. Inasmuch as the new transition lattices produced as the result of the deformation are different for each alloy, it was thought at first that the habits of the markings might be the result of a cooperation between matrix lattice and transformed lattice. (Both matrix lattices are body-centered cubic.) Such a cooperative effect is thought to obtain in the formation of Widmanstätten figures, for it is well known that the matrix lattice alone does not determine the habit assumed by a segregate phase. On the other hand, it is not inconceivable that the dissimilarity in mark-ing habit might be due to differences in deformation characteristics of beta brass and beta bronze. Barrett and co-workers2 have shown that slip-line habits in pure iron are markedly different from those in high-silicon ferrite; and although it has been repeatedly demonstrated that plates of a segregate phase do not necessarily form on the slip planes of the matrix lattice, deformation characteristics may be more intimately allied with plate formation when a transformation is made to occur as a result of plastic deformation. However, there is the fact that the orienta-tion of markings in metastable beta copper-zinc is the same whether the markings be produced by quenching, deformation, or liquid-air cooling; likewise, quenching and deformation markings in metastable beta copper-tin are oriented in the same way with respect to the beta matrix.

Jan 1, 1938

THE problem of reaction rates in the open-hearth process is essentially that of trying to form a fairly clear picture of the "chemical mechanisms" in the bath. Quantitative data on reaction rates would perhaps not be of much practical importance even if they were available; however, what few approximate data there are can be used in combination with data given in Chapters 16 and 17 to sketch a picture of the "chemical mechanics" of the open-hearth process that is consistent with essentially all the present available evidence. The result may later be found incorrect in many details but even so it will illustrate certain useful methods for obtaining a clearer understanding of the process. Consistent with the treatment in Chapter 15, but in simpler terms, we may say that chemical reactions in general involve the following elements or steps: 1. The reacting molecules are mixed together in space in such fashion as to favor collisions among them. 2. Units of what is usually an intermediate molecular arrangement called an activated complex are formed at a certain rate, depending on temperature and concentrations. 3. These activated complex units decompose into the reaction products (this step usually assumed to be so rapid as never to limit the over-all process). 4. In any of these steps, heat energy may have to flow into, or away from, the reaction zone to permit the reaction to proceed. 5. The products of reaction will usually have to move out of the way to permit further reaction. The temperature factor enters mainly through step 2, and its effect is very marked. (What is called temperature is really the mean energy content of all the molecules of the substance involved; at any one temperature a certain proportion of the moleculea will have much higher energy content than the mean value.) Various reaction rates measured at around room tem-

Jan 1, 1951

By G. B. Gibbs

Equations are developed which describe the growth of graphite nodules during a-phase graphi-tization under various limiting conditions. When carbon diffusion is rate controlling a modified Birchenall-Mead equation predicts an "apparent activation energy" of 31 keal mole-1 for the parabolic growth constant. If reaction at the graphite or cementite interface is the slowest process growth kinetics are linear and the activation energy must be >50 keal mole-1. A comparison with the experimental observations confirms that carbon diffusion determines the rate of reaction. Apart from minor approximations associated with Lou! carbon solubility in a iron the theory may also be applied to I-phase graphitization. It is well-known that cementite exists as a meta-stable phase in Fe-C alloys and that if a specimen is held at diffusion temperatures for a sufficiently long period the cementite decomposes and graphite is precipitated. Graphitization occurs by the nu-cleation and growth of carbon nodules and several impurity elements catalyze the reaction when present in minute amounts.1 The growth kinetics of nodules have been extensively investigated in the fee ? range2, 3 and recently in the bee a range.1, 4 Experimental growth curves (nodule radius vs time) have slopes which decrease with time, but the scatter of points is generally too great for the precise shape of the curves to be determined with certainty. Birchenall and Mead5 concluded that they are parabolic in ? iron, indicating diffusion control, and that the migration of carbon atoms determines the growth rate. Harris et al, 1 advanced similar ideas for a-phase graphitization. On the other hand, Burke3 chose to regard the initial growth region as a transient followed by a linear law indicating interface control (i.e., cementite decomposition or graphite crystallization as the slowest process). Jeminson and Higgins6 originally considered the initial steep portions of "parabolie" to represent a linear growth law also. In support of these ideas it has been noted that the apparent ac-

Jan 1, 1965

By S. Andrew Kulin, L. Kaufman

A general treatment of the broadening of X-ray double-crystal spectrometer rocking curves due to distributions of tilts and strains has been carried out. The results of this treatment have been applied to the case where dislocations in a crystal give rise to both tilts and strains. On this basis it is found that the rocking-curve halfwidth due to imperfections in the crystal, ßC , increases with increasing Bragg angle, 8. These considerations predict linear relationships between & and tan2 , and ßCand tan 8, for Gaussian and Cauchy distributions of dislocations, respectively. The zero intercept of the ßC us 8 curve, which is a measure of the degree of imperfection of the crystal, is found to depend directly on the distribution rather than the number of dislocations. In addition, the slope-intercept ratio for the ßc - ? curve has been calculated for both the Gaussian and Cauchy distributions. Experimental determination of the - 8 curves for a series of copper single crystals prepared by the Bridgeman and Czochralski methods yields results in agreement with the calculated slope-intercept ratio for a Cauchy distribution of dislocations. CERTAIN X-ray techniques have been used to study the perfection of single crystals. Gay, Hirsch, and Kelly have considered the spreading of spots into arcs on Debye-Sherrer rings due to imperfections. The Double-Crystal Spectrometer has also been applied to this problem.2 The characteristics of Double-Crystal Spectrometer Rocking Curves have been described in the literature by various workers.2-4 By assuming a random spacing of dislocations which give rise to a Gaussian distribution of misorientations relative to some mean orientation in a crystal Gay, et al.,1 arrive at the conclu- sion that the most probable misorientation is given by where h is the spacing between dislocations, and 8 and are the relative misorientations of neighboring regions. If ßC is the halfwidth of the rocking curve (the width at one-half the peak intensity) due to dislocations in the crystal then5

Jan 1, 1960

By M. D. Cooper

For the purpose of obtaining some first-hand data in regard to the shooting down of coal in bituminous mines, it was the writer's good fortune to be employed as a shot-firer for almost one year. In all, 6020 shots were fired by him during this period. All of the work was done in what is known as the South Main section of the No. 2 Mine of the Ellsworth Collieries Co., Ellsworth, Pa., a subsidiary of the Lackawanna Steel Go. Position of Shot-firing in the Cycle of Operations The established practice of the Ellsworth Collieries Co. calls first for the undercutting of the coal by electric chain machines across the face of the entry or room. This is followed by replacing any posts removed by the machine-runners, or the setting of new posts or timber, as may be required. After this has been done the machine cuttings are loaded into cars. Then the coal is spragged, and a shot hole drilled to the depth of the undercut. Next in order, the shot-firer loads the hole and fires the charge. The working place is then cleaned up, timbered if necessary, the sides and face squared up, and loose material taken down. The face is again ready to be undercut. Materials Used Permissible explosives were used exclusively in blasting coal. These were Carbonite No. 2, a nitroglyccrine explosive; and three different makes of ammonium nitrate explosives, Tunnelite, Red H, and Mine-ite 5-D. The last-named was used during the greater part of the period. It is interesting to note that even at the beginning of this work, the gases resulting from the explosions of the charges caused no especial distress on. the shot-firer's part and this continued to be the case except on the occasions when a change was made from one class of explosive to another.

Jan 1, 1918

By H. W. Morse

MANY of our largest copper deposits contain both sulfide and oxidized copper minerals. The large porphyry mines, with a total copper content of from 1.3 to 2.0 per cent., send to their mills ore with an oxide content of from 0.2 to 0.4 per cent. While the recoveries of the sulfide minerals are considered satisfactory, using modern flotation practice, the recovery of the oxi- dized portion of the copper is small; better recoveries of oxidized copper were made before flotation methods were adopted. Beside the ores containing copper mainly as sulfide, with a small amount of oxidized copper,, many of the large porphyry mines have oxide orebodies, in which the propor-tion of non-sulfide minerals is so high that 2 present methods of treatment are ineffi-cient. In some of the well-known ore-bodies in the Miami-Inspiration district the copper occurs about equally in sulfide and oxidized forms; and the mixing of minerals is complete throughout the ore-body. There is no possibility of mining the sulfides and the oxides selectively. At the New Cornelia mine, however, the oxide, and sulfide ores are sharply separated, per-haps by an ancient water level, so that the oxide ore may be mined and treated in a plant built for that purpose, and the under-lying sulfide ore may be left for treatment in another plant. If copper is to be made from an ore having a total content of 1.5 per cent., it must be concentrated or removed from the ore by some. hydrometallurgical method. Flotation is generally successful for the sulfide minerals and flotation after filming with sulfide seems to work in many cases on the pure carbonate minerals. Callow has given an extensive report on the results of "sulfidizing" flotation on the ores of the. Magma mine.1 Where such ?a 'method can be applied, it ?may be, the best

Jan 9, 1922

By Robert V. Whitman

INTRODUCTION Ideally, this paper should start by citing examples of slope failures in open pit mines during earthquakes. I do not know of any such examples, although - since my search of the literature has not been exhaustive - such examples may well exist. However, there certainly are many examples of devastating earthquake-induced landslides, and there is no reason why such landslides cannot occur at large open pits. Moreover, many of the actual earthquake-induced landslides have seriously affected mining operations in one way or another. Hence, this paper will treat earthquake-induced landslide phenomena in general, in the hope and expectation that the reader can apply this general knowledge to the specific problems associated with open pit mining. Ultimately, of course, the aim is to predict the likelihood of the occurrence of earthquake-induced landslides, and to delineate steps which can be taken to minimize the possibility of their occurrence. These aims can be achieved only imperfectly at the present time, for our knowledge concerning earthquake-induced landslides is still in an embryonic stage. Nonetheless, much useful knowledge does exist. In order to understand and apply this knowledge, it is necessary to: 1. Review the nature and extent of actual earthquake-induced landslides; 2. Have a grasp of the basic terminology and concepts of seismology; 3. Study the fundamentals of probability-based seismic risk analysis; 4. Appreciate the way in which earth materials behave during earthquake loadings; and 5. Have a general knowledge of the methods currently available for analyzing the dynamic response of slopes. Much of this paper is devoted to this necessary background. Information of practical use in connection with various classes of slope stability problems is assembled in the final sections. LANDSLIDES DURING PAST EARTHQUAKES Almost every earthquake in mountainous country, strong enough to be reported in the literature, has caused at least some landslides and rockfalls. Unless these slides or falls damage

Jan 1, 1971