Search Documents

By C. Altstetter

THE work herein reported is restricted to the carbides which occur in quenched and tempered AISI 43XX steels with carbon contents up to 0.40 pct and silicon additions of up to 3 pct. In view of the instability and extremely small size of the carbides formed at low tempering temperatures, the technique for successfully preparing specimens for X-ray diffraction will be outlined. The alloys listed in Table I were obtained through the courtesy of the United States Steel Corp. in the form of 1/2-in. rounds forged from 100 lb. induction furnace heats (except for 4337 which was a commercial heat). The stock was normalized and then swaged and drawn to 15 mil wire with anneals at 1200F between passes. The wire was austenitized for 45 min in evacuated vycor capsules and quenched into iced brine with simultaneous smashing of the capsule. Tempering was done in air with a water quench after tempering. The carbides were extracted in a simple cell using a solution of 1M KC1 and 0.5 pct citric acid with an initial current density of 0.1 amp per sq cm. One end of a short length of wire was immersed in the solution, and the current at constant voltage was noted as a function of time. After about an hour the current dropped sharply because of the decrease in specimen cross-section. At this point it was found that the dissolution could be stopped and that the very fine wire which then resulted was just large enough to permit handling of the extracted precipitate still clinging to it, yet so small that it diffracted and absorbed only a negligible amount of the X-radiation. This rod of residue with a convenient handle of undissolved wire was rinsed in distilled water. alcohol, and acetone. Then it was dipped in a thin solution of cellulose-acetate cement and dried in vacuum. The resulting specimen was straight, uniform in density, easily handled, but most important, was completely sealed and never exposed to air. Furthermore, the residue had never been subjected to strong acids or rough handling such as in the extraction-replica technique or in the complete extraction to a powdered residue. It was found that improperly coated specimens were pyrophoric, turning to oxide with a dull red glow as they were exposed to air and yielding patterns of Fe2O3 and Fe3O4. The steels containing 3 pct Si were especially difficult to prepare for this reason. The specimens were put in a 57 mm Straumanis camera with double pinholes or slits and irradiated with filtered-chromium radiation. Readable patterns were obtained in less than an hour. A preliminary finding of some note was that for both tempered and as-quenched specimens of steels 4337 and 4337 (1.5 Si). M23C6 patterns were found along with the patterns of other constituents of the residues. This result was somewhat surprising in that previous investigators had reported that this carbide did not appear in a 0.38 pct C, 0.48 pct Mo steel1 or in chromium steels of less than about 10 pct Cr.2 Although the total amount of carbide-forming alloying elements is less than 2 pct, due to their mutual interaction and the action of the plastic deformation in promoting equilibrium, this carbide was able to form even in the steel containing 1.5 pct Si. M23C6 was not detected in the 4337 (3.0 Si) steel and the lower-carbon steels were not investigated in this condition. It is very likely then that the steels studied herein underwent a fourth stage of tempering during the anneals at 1200°F. This result has significance in that even a small amount of undissolved M23C6 in a low-carbon, low-alloy steel would exert a large effect on its hardenability. Its presence would also influence the mechanical properties by decreasing the carbon content of the matrix. Annealing in vacuum for 1 to 4 hr in the austenite field removed all traces of MZ3C+ The results on carbide precipitation during tempering, summarized in Table I, are in agreement with those of Klingler et al.3 for the higher carbon steels. For the AISI 4337 steels it is noteworthy that in the steels with added silicon the E carbide persists to longer times and higher temperatures and that silicon delays the formation of cementite. The results for the lowzr-carbon steels parallel those of the higher-carbon grade. The appearance of E carbide in the AISI 4315 is significant. There is considerable disagreem-nt in the literature as to whether this carbide forms in the tempering of steels containing less than about 0.2 pct C. Following the detection of E carbide in a 0.18 pct C plain-carbon steel,4 its occurrence in a steel containing chromium and molybdenum should be expected. The fact that the low-carbon steels have the same carbide-precipitation sequence as the high-carbon steels has bearing on the larger problem of the exact tempering reactions in all steels. Following the suggestion of Roberts et al.,' the first stage has been generally assumed to result in a metastable equilibrium of c carbide and martensite of about 0.25 pct C. From this it was concluded that a steel having less than 0.25 pct C should then be under-saturated with respect to c carbide and should not precipitate this carbide upon tempering. In view of the experimental findings of c carbide in steels hav-

Jan 1, 1962

By E. W. Johnson, M. L. Hill

Cold working of iron-carbon alloys was found to increase greatly the hydrogen solubility and to decrease the diffusivity at temperatures up to 400° C. These effects are increasing functions of both the carbon content and the degree of deformation. The hydrogen behavior is consistent with the idea that cotd working creates "traps", which are concluded to be microcracks in which the hydrogen is chemisorbed. Hydrogen embrittlement is explained by the Petch theory of metal crack surface energy loss due to hydrogen adsorption. HYDROGEN embrittlement of steel has been studied for many years and has been the subject of an extensive literature, but the mechanism of the effect has not been completely understood. The embrittlement is unusual in that the ductility loss is not accompanied by an increase of the yield strength, being primarily a decrease of the fracture strength alone. The loss of fracture strength is usually most severe in the temperature range between 0°and 100°C. Here the solubility of hydrogen in the iron lattice at ordinary H2 pressures is extremely low while the diffusivity is still quite high. From the relationships between the ductility and the hydrogen content, test temperature and strain rate, it is apparent that the hydrogen atoms causing the ductility loss difbse to and concentrate in small regions of the metal which are especially susceptible to the initiation and propagation of fracture. This hydrogen segregation apparently occurs after plastic straining has begun. Below 0°C the ductility loss persists only at low strain rates in confirmation of the view that the embrittlement is diffusion .controlled. The tendency of the embrittlement to disappear above 100°C can be explained by the increasing lattice solubility of hydrogen with rising temperature. A common view of hydrogen embrittlement of steel is that the hydrogen initially dissolved in the metal lattice diffuses to structural discontinuities and there precipitates as H2 gas at very high pressures which assist the external stress in causing premature failure.1,2 The idea of a high H2 pressure in equilibrium with ordinary amounts of hydrogen in steel at room temperature is due to observations of hydrogen behavior in fully annealed material, for which the Sieverts' law constant relating solute concentration to H2 pressure is extremely small. Hydrogen-embrittled steel, however, is always plastically deformed to some extent, and therefore it is important that hydrogen embrittlement be explained primarily in terms of hydrogen behavior in plastically deformed material. Such an explanation is attempted in this paper. Previous studies of hydrogen in cold-worked steel have shown that both the solubility and the diffusion rate are significantly chaned when the steel is cold worked. Darken and Smith discovered that the amount of hydrogen absorbed from acid by cold-rolled steel at 35°C is many times greater than that absorbed by hot-rolled steel. They found also that the hydrogen permeability of the steel is unaffected by cold working. Keeler and Davis4 confirmed the high apparent solubility of hydrogen in cold-worked iron-carbon alloys at temperatures up to and even beyond the recrystallization temperature. They also found that this solubility increase accompanying cold work is a sensitive function of the carbon content, being absent when no carbon is present. The present experimental study was undertaken primarily to obtain an improved understanding of the behavior of hydrogen in cold-worked steel. Data were obtained on the effects of temperature, H, pressure, carbon content, and degree of cold work on the hydrogen solubility and diffusivity in iron-carbon alloys. These data have been helpful in elucidating the nature of the cold-worked steel structure as well as in providing information on the mechanism of hydrogen embrittlement of steel. EXPERIMENTAL Cylindrical specimens for hydrogen absorption and diffusion rate measurements were prepared from three iron-carbon binary alloys and a commercial SAE 1010 steel. The iron-carbon alloys were prepared by vacuum melting electrolytic iron with graphite in a magnesia crucible. The alloys were cast in vacuum as 2 1/2-in. sq ingots weighing about 20 lb each. The ingots were hot rolled (above 1900°F) to 5/8-in.-diam round bars and then cooled in air to room temperature. The resulting metallographic structure consisted of islands of fine pearlite surrounded by free ferrite. Chemical analyses of the materials are given in Table I. The 5/8-in. diam bars were turned to diameters such that cold reduction to the desired final specimen diameters would result in either 30 or 60 pct reduction in area (RA). The machined bars were then cold worked by swaging at room temperature

Jan 1, 1960

By M. Metzger, T. A. Read

The strengthening effects of hydroxide and synthetic plastic films in the creep of cadmium crystals were studied. The results were broadly consistent with the naive mechanical model. The dislocation-film reactions and the significance of the macroscopic stresses associated with certain films are discussed in the paper. ALTHOUGH a number of studies have been made of the strengthening of metal single crystals produced by surface films usually less than Ir in thickness, the mechanisms underlying this phenomenon are still not well established. Roscoe' first noted the critical shear stress and the stress-strain curve of cadmium-crystal wires to be raised markedly by the presence of oxide films. Subsequent investigators2-' have confirmed the effect for several metals and films including a number of plated poly-crystalline metal films. Harper and Cottrel1" with a thin film on zinc presumed to have formed as a result of etching and washing treatments) did not detect a strengthening at a rate of extension of 10 ' sec-' although at lo-' sec-' the film raised the flow stress by 7 pct at 0.0005 extension and by 22 pct at 0.01. The marked strengthening at moderate strains thus appeared to be the result of a dynamical effect dependent on the rate and amount of plastic flow. Other observations'. " are consistent with this view. The large effects of films on the tensile creep rate of single crystals were demonstrated when the observation of Andrade and Randall," that the creep rate of cadmium crystals increased on immersion in aaueous solutions of certain cadmium salts. was shown' * to hold only when a film was present initially and was explained by the attack of the solution on the film and the removal of its strengthening effect. Changes in the creep rate interpretable in terms of the removal or formation of various films have been observed by other investigators.3,8,10,31 Certain other experiments have been reported in which surface films or liquid environments have affected the plastic behavior of metals, but these are not within the scope of the present work which deals with the effect of solid films on single-crystal slip. Possible Mechanisms—The film does not significantly reduce the load on the crystal in the elastic range (the elastic moduli of film and crystal are not too greatly different and the area of the film is so small that its share of the load is negligible) so that the initial operation of internal Frank-Read sources is not affected. However, as Fisher" has pointed out, a source terminating on the crystal surface requires only half the critical stress for activation as an internal source of the same length and a relatively strong film (even a very thin one) would pin the free ends of the surface sources so that, if surface sources are responsible for plastic flow in a clean crystal. such a film would increase by roughly a factor of 2 the stress necessary for generation of dislocation loops at a given rate. The other general possibility is that the film resists the passage to the crystal surface of internally generated dislocations. If the film is adherent and if the specimen is to exhibit slip of the same general character as a film-free specimen, the film must deform or fail in shear at the active slip planes. The naive mechanical model, where shear-stress relaxation across the active slip plane in the metal transfers load to the film until it deforms and slip can

Jan 1, 1959

By M. C. Miller, M. R. Tek, D. L. Katz

Previous studies have shown the influence of geometric variations on the drawdown and buildup behavior of a well completed in a homogeneous, porous medium containing a single-phase fluid. Other papers have shown the influence of leakage across caprocks on drawdown tests on water wells and aquifers. This paper presents two additional cases: the influence of an adjacent, expansible source of fluid, and the effect of caprock leakage on the measured in situ permeability and compressibility. Methods are developed for evaluating the influence of these two deviations from a uniform aquifer upon the in situ permeability and compre.ssibility indicated by pump tests. INTRODUCTION In relatively uniform porous media, saturated with a single-phase fluid, the effective reservoir permeability and compressibility of the water porous bed system may be obtained from drawdown and build-up data on wells, such as the initial wells drilled in aquifer storage reservoirs (Homers and Katz et al.7). In considering the drawdown and build-up behavior of wells adjacent to storage reservoirs, or of wells in an aquifer adjacent to an unknown gas field, questions arise as to the quantitative effect of the presence of compressible fluid on the measured permeability and compressibility of the formation. The solution to this problem is presented, using a constant pressure line source at some distance from two wells, one of which is pumped and the other used as the pressure observation well. The solution is presented in terms of the geometry of the wells and their relationship to the constant pressure line. It is known that caprock leakage can interfere with the determination of an aquifer in situ permeability and compressibility (Mantush4, Hantush and Jacob3 and Witherspoon and Muellerll). This paper presents an added case of the effect of leakage through a caprock of known thickness and permeability on well tests starting with a reservoir of constant pressure above the caprock and contributing to the aquifer as a result of the pump test. Again, both a pumping well and an observation well are postulated. These two cases are presented together since both a compressible fluid nearby and. caprock leakage show similar deviations from expected in situ permeability and compressibility results, and the solutions are similar in form. EFFECT OF A NEIGHBORING CONSTANT PRESSURE SOURCE ON IN SITU MEASUREMENTS Bixel, Larkin and van Poollenl presented a paper showing the influence of a discontinuity of the properties of a fluid formation system on drawdown and build-up performance. Their case is related to the present study but may be distinguished from it in that their numerical work and resulting graphs relate only to the performance of the pumping well itself. Incorrect values for in situ reservoir properties may be obtained from pump test data if the skin effect of the well and after-flow are not considered. Analysis of this problem by the authors indicated that the more reliable method of evaluating the influence of an adjacent gas field or expansible source was to use one well for pumping and another well at some distance from it for observing the aquifer pressure performance. An expansible source of hydrocarbon near a pumping well may be approximated by a line of constant pressure for a pump test. Fig. 1 illustrates a pumping well and an observation well near a line of constant pressure. Pressure behavior of an observation well during a drawdown pump test near a line of constant pressure is given by the diffusivity equation:

Jan 1, 1967

By E. A. Trager, A. W. McCoy, H. R. Shidel

Sampling of the fluid from oil wells for percentages of oil, emulsified oil, and water during the last two years has brought out some interesting facts concerning oil-water emulsion. This result led to a laboratory investigation of emulsion, which substantiated the conclusions made from the field observations. The purpose of this paper is to present the information collected, the laboratory experiments, and our interpretation of the same. In order to define emulsified .oil exactly, give its synthesis and origin, and to show how and when it is formed in the wells, the work was necessarily divided into two separate lines—laboratory work and field observations. It is hoped that this study may lead to a discussion of such points so that the petroleum engineer, geologist, or technologist may be benefited by its practical bearing on oil-field management. Special credit is due Mr. Everett Carpenter, chief geologist of the Empire Gas & Fuel Co., for his assistance and cooperation in this work. Labobatory Investigations on Emulsified Oil Laboratory investigations were conducted in an attempt to learn the composition and some of the properties of emulsified oil, or B. S., as it is more commonly called, also to demonstrate, by laboratory methods, how B. 5. may be formed under conditions similar to those existing at the time a well is being pumped, and how it may be broken down. Literature bearing on this subject is widely scattered and very limited in scope. Bacon and Hamor define B. S., or bottom settlings, as "earthy matter, inert organic matter, or, in the case of Pennsylvanian petroleum, an emulsion of paraffin wax and water, which accompanies crude oil." In this discussion we will limit the term B. S. to that heavy, dark-brown emulsion, composed of a physical mixture of water, oil, and air with some included inert matter, either organic or inorganic. Possibly the first step in a description of this product should be a description of its physical properties, but since most operators are quite

Jan 1, 1921

By Frederick M. Becket, Russell Franks

WideSpread experimentation has been conducted in recent years to devise a means of preventing intergranular corrosion in austenitic chromium-nickel steels of the 18 per cent chromium-8 per cent nickel type. Additions of titanium to these steels have been used commercially to overcome this dificulty, as advocated by Krupp of Germany, and the latest literature reference concerning improved details of this method is the article by Bain, Aborn and Rutherford.' Extensive work by the present authors has shown columbium also to be a particularly valuable agent for inhibiting intergranular corrosion. This paper does not deal with steels that are largely or wholly austenitic; it is limited to a discussion of the results obtained through the use of titanium and columbium in plain high-chromium steels. For many years titanium has been used commercially by some steelmakers as a cleanser, and to a lesser extent as a hardener, but then in greater percentages. The results of the work to be described disclose that titanium and columbium in proper Proportions act as effective softeners in the high-chromium steels. It is well known that chromium intensifies the hardening effect of carbon in steel; it imparts pronounced air-hardening properties within a rather wide range of chromium content; it provides increased ductility in steels of given strength and hardness; and it enhances resistance to corrosion and oxidation at elevated temperatures to a marked degree. However, in applications requiring a combination of some of these valuable properties great hardness is frequently a detriment rather than a merit. When the objective is a soft and ductile steel having optimurn corrosion resistance, the producer strives for a carbon content as low as commercially practicable. Despite these efforts some of the commercial high-chromium steels low in carbon present considerable difficulties during production, owing to their air-hardening properties, and in consequence the economic result is not favorable. A good example is found in the 5 to 6 per cent chromium steels employed chiefly in the oil-cracking industry. Sleels

Jan 1, 1934

By Karl Sundberg

ELECTRICAL investigations carried out in regions containing sedimen-tary rocks showed that sediments generally are good electrical conductors, a fact which at the present time is used for structural investigations by electrical methods. It is of fundamental importance, not only for these investigations but also for electrical prospecting in general, to know the electrical properties of various soils and rocks. It will be useful, there-fore, to discuss this question with the hope that the general points of view discussed in this paper will perhaps be, completed by further observations and determinations of material from various localities. This paper is based principally on the study of literature, and the purpose is primarily a discussion of the main factors that determine the electrical conductivity of soils and rocks. It will follow, however, that the factors discussed here also frequently decide how far a certain orebody can be regarded as a good electrical conductor compared with the sur-rounding rocks. All-rocks are more or less porous; and the pores are filled with liquids and gases. Their electrical conductivity, therefore, depends on the following factors: 1. The electrical conductivity of minerals composing the rock. 2. Electrical conductivity of the liquid filling the pores. 3. Proportion of the volume of liquid filling pores of the rocks to the solid rock material. 4. Shape of the pores. 5. Arrangement of the particles of gas and liquids. 6. Temperature. Dry minerals, with the exception of certain ore minerals, are complete nonconductors from the point of view of applied geophysics; in the present investigation we deal with rocks which have no conducting minerals, and factor 1, therefore, is not important. The same is true of soils. The liquids contained in soils and rocks in most cases are waters, some-times oil. As oil is a nonconductor of electricity, the impregnating waters will determine the electrical conductivity of soils and rocks.

Jan 1, 1932

By Andrew W. Jenike

STORAGE AND FLOW Introduction The layout and design of a bin or stockpile for bulk solids should assure reliable feed at the required time and rate without spillage and, when required, without segregation and degradation. The typical procedure in the design for gravity flow follows these steps: 1. The bulk solids to be stored are identified and the range of moisture content, temperature, feed rate and time of storage at rest, as well as the storage capacity, are specified. The materials of construction of the hopper, that is of the converging part of the bin, are decided upon. Hopper liners and coatings to reduce wall friction are considered. 2. The flow properties of the bulk solids and the friction angles against the wall materials are measured for the expected range of conditions. 3. The width of a slot outlet needed for reliable flow of each solid under the full range of conditions is determined from the tests. This dimension is an explicit measure of flowability of a solid. The widest slot determines the critical solid and the critical conditions. 4. A suitable feeder of size sufficient for the widest slot outlet is selected. 5. On the basis of the measured wall friction angles, a suitable wall material is selected and a mass flow hopper is designed to ensure reliable and uniform flow of solid into the feeder and to minimize the load on the feeder. The mass flow hopper may extend upward to the intersection with the cylinder thus producing a mass flow bin. Alternatively, the hopper may terminate at a height equal to a few widths of the outlet and then expand at a less steep slope in its upper part in order to save headroom, or it may terminate in the flat bottom of a bin or stockpile. The choice depends on the flow properties of the solids and the size of the bin or stockpile. 6. The design of the bin is completed for the specified storage capacity. Multiple hoppers and

Jan 1, 1982

By P. D. P. Hamilton

In any mining district where benefication of the ores is practiced, one can usually observe several types of flow sheets even though the various producers are milling ore from the same geological formations. It is obviously impossible to describe all the mills in the Porcupine district. However, the following description of some of them is of particular interest in that it shows where one mill has paid particular attention to corduroy blanket practice; one to gravity concentration of sulfides for intensive cyanidation of the values therein contained; one to flotation of values and cyanidation of this product only; and others where small variations of standard all-slime cyanidation practice prevail. In all cases it will be seen that cyanidation is the basic principle. Discussions involving the difference in the flow sheets and the reasons for them will always be of value to those interested in the art. The author of this article, however, believes that such discussions should originate from the operators of the mills under discussion. For this reason no comparisons or discussion will be included in the description of the mills mentioned. Should any reader of this article obtain information therefrom which will be of value to him in helping to solve his own particular problems, the author will consider that the article has satisfactorily served its purpose. All values mentioned throughout this article are based on the value of gold at $20.67 per ounce. Coniaurum Mines, Limited The ore of the Coniaurium mines consists of a mineralized schist and quartz containing about 2.5 per cent sulfides. Owing to the low grade of ore developed in the mine, extreme care has had to be exercised throughout the entire mining and milling operation in order that an operating profit might be obtained. The management, however, has been able to keep costs down, with the result that at present the outlook for the property is considerably brighter than it has been in the past. This is partly due to the fact that it is now known how to mine and treat

Jan 1, 1935

By C. A. Pierce

Studies of roof and floor movement are of interest to those actively engaged in mining. This is especially true in the case of an entirely new area where there is no precedent for guidance. The potash deposit being mined is in the southeast corner of New Mexico, about 20 miles east of Carlsbad. The deposit was formed by the land-locked, shallow, Permian Sea that extended through parts of western Texas, Oklahoma, Kansas, southeastern Colorado, and eastern New Mexico. The saline deposits vary from 500 to 4000 ft. thick. Neither of the companies operating in this area has delimited its commercial ore bodies. As all production so far has been from Federal and State leases, the Department of the Interior and the State of New Mexico have a direct interest in the development and extraction of these ore horizons. The ore is composed of an intimate mechanical mixture of sylvite (potassium chloride) and halite (sodium chloride). It lies generally in a horizontal bed varying from 5 to 12 ft, in thickness, and has a cover of approximately 1000 ft., consisting of about 500 ft. of salt beds and 500 ft. of sediments. The immediate mine roof for several feet is principally salt with some potash and clayey material. The next 500 ft. above, from the standpoint of structure, may be considered rock salt with a few inter-bedded potash members. The upper 500 ft. is of sedimentary (Permian and Triassic) origin and contains several water-bearing formations with flows varying from 10 to 500 gal. per minute. This water intensifies the interest in convergence problems as the ore and surrounding formations are water soluble. Potash salt (sylvite) and rock salt (halite) are plastic minerals. Plasticity is defined as a "property of solids by virtue of which they hold their shape permanently under the action of small shearing stresses but are readily deformed, worked, or molded under larger stresse."1

Jan 1, 1942

By C. A. Pierce

Studies of roof and floor movement are of interest to those actively engaged in mining. This is especially true in the case of an entirely new area where there is no precedent for guidance. The potash deposit being mined is in the southeast corner of New Mexico, about 20 miles east of Carlsbad. The deposit was formed by the land-locked, shallow, Permian Sea that extended through parts of western Texas, Oklahoma, Kansas, southeastern Colorado, and eastern New Mexico. The saline deposits vary from 500 to 4000 ft. thick. Neither of the companies operating in this area has delimited its commercial ore bodies. As all production so far has been from Federal and State leases, the Department of the Interior and the State of New Mexico have a direct interest in the development and extraction of these ore horizons. The ore is composed of an intimate mechanical mixture of sylvite (potassium chloride) and halite (sodium chloride). It lies generally in a horizontal bed varying from 5 to 12 ft, in thickness, and has a cover of approximately 1000 ft., consisting of about 500 ft. of salt beds and 500 ft. of sediments. The immediate mine roof for several feet is principally salt with some potash and clayey material. The next 500 ft. above, from the standpoint of structure, may be considered rock salt with a few inter-bedded potash members. The upper 500 ft. is of sedimentary (Permian and Triassic) origin and contains several water-bearing formations with flows varying from 10 to 500 gal. per minute. This water intensifies the interest in convergence problems as the ore and surrounding formations are water soluble. Potash salt (sylvite) and rock salt (halite) are plastic minerals. Plasticity is defined as a "property of solids by virtue of which they hold their shape permanently under the action of small shearing stresses but are readily deformed, worked, or molded under larger stresse."1

Jan 1, 1942

By Hubert O. DeBeck

The following descriptions and explanations apply specifically to the use of the Hotchkiss Superdip, but there are no apparent reasons why they should not apply to any magnetometer. This paper is a product of work in the practical field for several years with the Hotchkiss magnetometer, mostly on mineral deposits in the southeastern United States. The paper describes the result of an attempt to develop a practical and economical field method that approaches, as nearly as possible, the utmost accuracy of which the magnetometer is capable. As there are many published descriptions of various magnetometers and magnetic methods, it would be superfluous to describe such instruments here, but a limited bibliography on the Hotchkiss and Askania magnetometers is appended. The Hotchkiss and the vertical Askania magnetometers have, respectively, maximum sensitivities of approximately 5 and 30 gamma per instrument scale division. Purpose of New Method The purpose of the method described in the following paragraphs is to eliminate, as far as possible, all corrections of field data that cause complexities and inaccuracies in the results of magnetometer surveys. Magnetometer field observations must be corrected for periodic variations in the intensity of the earth's magnetic field, as well as for temperature variations, both of which take place during the course of a day. These variations do not seriously handicap magnetometer work on highly magnetic deposits, but it is impossible to obtain accurate results, by the conventional methods in use today, over weakly magnetic or diamagnetic deposits. This is due to the physical inability to obtain by such methods sufficiently accurate data in the field to make dependable corrections. The magnitude of the necessary corrections of field observations frequently exceeds the magnitude of local magnetic anomalies obtained over various types of mineral deposits. Therefore if these corrections are neglected or made on the basis of inaccurate data, the entire magnetic picture of the area concerned is at least distorted, and perhaps destroyed altogethcr.

Jan 1, 1934

By I. L. Greninger

THE property of the Andes Copper Mining Co. is in the central part of the Republic of Chile, Province of Atacama, 147 km. (91.5 miles) eastward by rail from the port of Chanaral. At this point the Andean system is made up of two principal ranges. The mine is on the westerly slope of the outer, or western, range, at a mean elevation of 3250 m. (10,500 ft.). A meter-gage railroad extends from the company's port at Barquito, near Chañaral, to the reduction plant at Potrerillos. This road has a total length of 151 km. (94.0 miles), of which 93 km. (57.79 miles) are owned by the Andes Copper Mining Co. The remainder of the road is owned by the state. The company operates its trains over the portion of the road owned by the state, under an agreement with the Chilean Government. The mine is connected with the reduction plant by a meter-gage railroad, 10 km. (6.214 miles) long, which extends from the coarse-ore bins at the metallurgical plant to the underground storage bins at the mine. Tunnels make up 60 per cent. of the total length of this railroad. As is characteristic of the Andean region in Chile, the topography of the locality is extremely rough, and a number of points near the mine have elevations of from 15,000 to 16,000 feet. History of Potrerillos Mine The ore occurrence has been known for many years, and many of the claims under individual ownership were worked in a small way before the property was acquired by the present owner—the Andes Copper Mining Company. The highest grade oxide ores near the surface were mined by primitive methods and, after sorting, the product, assaying around 15 per cent, copper, was hauled by mule carts a distance of about 80 km. (49.71 miles)

Jan 1, 1929

By W. H. Burke

Deeper drilling, resulting in greater circulating distance and pressure, has directed attention to the advantages of the study of properties and control of rotary muds, which until recently have not had much consideration. One fundamental property of muds is viscosity, and viscosity is influenced by the quantity and character of colloidal material and can be controlled by chemical treatment. Colloidal Matter of Rotary Muds Two types of colloids are found in muds; the hydrophobic and the hydrophilic. Hydrophobic colloids do not associate intimately with water and are sensitive to small quantities of electrolytes. Hydrophilic colloids associate intimately with water, but are not so sensitive to electrolytes. The colloidal particles of rotary muds are derived from clay; In clay the particles may range in size from submicroscopic to macroscopic; a substance is a clay if the greater proportion of the particles are within the size limits prescribed for clay. The larger particles are inert and have no effect on the viscosity of normal hydrophobic colloidal muds. There are two theories accounting for the colloidal properties of clay-water suspensions: (1) the physical theory, that clay in water is a coarse colloidal suspension, and (2) Ashley's1 theory, that clay is a granular material with a colloidal gel surrounding the crystalline grains. The most important colloidal substances known to exist in clays besides the clay particles are: (1) colloidal silica, (2) colloidal alumina, (3) colloidal ferric hydroxide, (4) colloidal silicates, and (5) colloidal organic matter. Plasticity, a peculiar property of clay-water suspensions, is due to the colloidal particles. It is commonly (although not with strict accuracy) measured in terms of viscosity, and depends upon the amount and the state of flocculation of the colloidal matter present in the suspension. Fluidity in a rotary mud may be caused by a lack of colloidal clay particles or by deflocculated or flocculated clay particles, while viscosity in a

Jan 1, 1935

By V. Lessels, D. J. Buckwalter, D. H. Rose

A cyanide leaching process developed at Michigan Technological University was tested in a 12 to 24 tpd pilot plant. Flowsheet layout and equipment are described. Cyclic operation of leaching, copper precipitation by acidification, and regeneration of the cyanide leaching solution are discussed. Copper extraction and reagent consumption were as predicted by laboratory tests, and the process was proven to be technically feasible. The White Pine Copper Co., a wholly-owned subsidiary of the Copper Range Co., produces copper in the Upper Peninsula of Michigan. Production in 1965 amounted to 138 million pounds of metal. An expansion program now under way will increase this by approximately one half. The highly mechanized room and pillar mine produces 18,000 tons of ore per day, which is treated in a flotation plant. The concentrate is smelted in a reverberatory furnace, the matte is blown in converters to blister copper, and the blister copper is further refined to a uniformly high-quality Lake copper, which is 100% conductive and has a silver content of 25 to 40 oz per ton. The run of the mine ore averages 22.5 lbs of copper per ton with the ore mineral occurring in the form of chalcocite. The nature of the mineralization is such that the sand tailings average a little over 4 lbs of copper per ton. Intensive research has improved copper recovery in the flotation operation to some extent, but at the scale of present operation about 12,000 tons of sands containing over 48,000 lbs of copper go to the tailings pond daily. When the plant expansion is completed, the loss of copper will be somewhat greater. In 1959, the White Pine Copper CO, initiated a study of the recovery of copper in the sand tailings. Inasmuch as the flotation operation was considered to be optimized, a logical approach seemed to be leaching. For various reasons ammonia, ferric chloride, acid, and biological leaching were ruled out as impracticable. This led to a consideration of cyanide leach-

Jan 1, 1968

By J. M. Locke

Bruckner's revolving cylinders for roasting ores, etc., are now used at a number of the mills in Colorado and New Mexico, for the purpose of roasting and chloridizing silver ores, with highly satisfactory results, even from those cylinders of small size, erected before the many improvements of recent date. AS examples of the larger improved cylinders, reference can be made to those erected at the Tennessee Reduction Works, Silver City, Grant County, New Mexico, and those which were built, in 1871, at the celebrated Caribou Silver Mill and Mines, Colorado, a mining enterprise which has proved so satisfactory as to have been lately sold to a Holland company for an enormous amount. These cylinders, as now constructed by Messrs. Lane & Bodley, of Cincinnati,,Ohio, are shown in Plate 111, in which Fig. I is an elevation in perspective, Fig. 2 a longitudinal, and Fig. 3 a transverse section. Fig. 4 is a sketch of a mill, with Bruckner's cylinder. The exterior of the cylinder is a shell of boiler iron, 12 feet long by 5 feet 6 inches in diameter. The ends are partially closed with similar material, leaving in the centre a circular opening about 2 feet in diameter, bounded by a flange projecting several inches. Upon one side is placed an opening closed by a hinged door. Upon the outside of the cylinder are bolted three bands, as shown in Fig. 1, in which the section of the first is square, and that of the third semi- . circular; the second, or middle band, is a strong spur gear. Passing through the cylinder are six pipes parallel to one another, in a plane at an angle of 15" to the axis of the cylinder; these pipes also lie in this plane at an angle of from 30" to 35' to the longitudinal .axis of the plane, as shown in Fig. 2, where the internal arrangement of the cylinder is seen, a perforated diaphragm being formed through part of the cylinder by means of perforated plates placed between

By C. E. Violet, R. J. Borg, E. M. Howard

The miscibility gap in the Au-Ni system has been determined by Mossbauer spectroscopy, with used as a probe. The phase boundaries were determined from the compositional dependence of both the isomer shift and Curie temperature. X-ray diffraction measurements were also used to confirm the Mossbauer results. 1 HE purpose of this research is to demonstrate the application of Mbssbauer spectroscopy to the determination of phase boundaries and to redetermine the miscibility gap by an independent and novel technique. The techniques evolved in this study are readily applicable to other polyphase systems and are generally as quick and accurate as the more conventional methods, e.g., metallography, X-ray diffraction, thermal analysis, and so forth. To be sure, not all polyphase systems will lend themselves favorably to Mijssbauer investigations, but this is a problem met in the use of conventional methods as well. The Mbssbauer spectrum responds to a different set of physical parameters, and consequently provides an entirely independent method of analysis. It is especially useful if the system has either a ferromagnetic or an antiferromagnetic transition. The Au-Ni system was selected because alloys containing more than -60 at. pct Ni become magnetically ordered at low temperatures; also the miscibility gap is quite well established (see Ref. 7 for a compilation of pertinent references, also Fig. 11, and thus provides a reliable test of this novel procedure. As Fe is the most commonly used Mijssbauer isotope, there exists a wealth of information concerning its behavior in iron-containing alloys and compounds. However, as yet there have been relatively few experiments using it as a probe to investigate nonferrous systems. By choosing a nonferrous alloy system, we are able to demonstrate that its use is not restricted to systems containing iron as one of the major constituents. Wertheim and ~ernick' have used the same method to investigate Cu-Ni, and demonstrated that one can obtain a systematic variation in the isomer shift and magnetic hyperfine field. However, we believe this to be the first time these techniques have been used to establish phase boundaries. Two hyperfine interactions were measured and used to determine the phase boundaries, viz., the magnetic hyperfine splitting and the isomer shift which in this alloy system are both strong functions of composition. Calibration curves were established based upon single-phase solid solutions obtained by quenching from temperatures well above the maximum of the miscibility gap, see Fig. 1. Solid solutions containing 25, 50, 65, 75, 85, 92, and 96 pct Ni as well as pure nickel were used in the calibration procedure. Fig. 2 shows the Curie temperature, TC, and the isomer shift, v,, as determined from the Mbssbauer spectra, and variation in lattice parameter as determined by X-ray diffraction, as functions of composition. The compositions of the two-phase systems quenched from temperatures within the miscibility gap are obtained by comparing their respective values of TC and v0 with the calibration data. I) EXPERIMENTAL Mbssbauer sources were made by fusing the component metals in a tungsten arc melter, which has a water-cooled copper hearth. Both nickel and gold were 99.999 pct pure, and the melting was done in an atmosphere of purified argon. The alloys were rolled, diced,

Jan 1, 1969

By L. C. Armstrong

Twice in the past two years and in two widely separated localities—ane near Williamsville, Mo., and the other in the Allard Lake district of Quebec— the Contract Drilling Division of the Longyear Company has experienced perplexing difficulties in drilling granitoid igneous rocks. The rocks in both places are characterized by appreciable amounts of feldspar intimately inter-grown with quartz particles of microscopic dimensions. The disappointingly slow rate of advance and the exceptionally high bortz loss, obtaining during the life of these two projects, are ascribed largely to the resistance to abrasion of these two minerals when arranged in this intergrown pattern. Whether all intergrowth-bearing igneous rocks would offer extraordinary resistance to bit progress cannot be stated with assurance on the strength of these experiences alone. More data on diamond drilling this sort of material in a number of localities are needed before any generalizations can be made safely. It should be pointed out that the lack of time and funds made it impossible for the writer, or other persons interested in correlating the details of bit histories with the kinds of rocks drilled, to be present during the performance of the contracts. However, the records kept in the normal course of drilling are deemed complete enough to be reportworthy. This information is presented here together with the findings made in studies of the rocks involved, with the thought that it may attract the comments of others who may have encountered similar refractory drilling conditions. A pooling of knowledge on the problem would be of material aid in devising more efficient cutting tools and procedures for penetrating this kind of rock. Drilling Blastholes in the Williamsville Granite Due to the unsatisfactory perform- ance of pneumatic percussion drills in boring blastholes on a construction contract near Williamsville, Mo., tests were made with a diamond drill. The poor progress achieved and the excessive loss of diamonds, however, soon led to the abandonment of these trials. The diamonds, in all of the bits tried, lost their cutting edges and acquired a polish after being in service for distances ranging from a few inches to a few feet. Coring bits containing surface-set, whole-stone bortz in a tungsten powder matrix were employed. The cost assignable to bortz wear averaged $7.17 per foot. This item of expense is several times the amount normally expended in diamond drilling in firm, unfractured, granitic rocks. Diamond-impregnated, tungsten carbide bits also were used without success. The diamond wear was at the rate of $0.98 per foot, but the diamond chips became too polished for further duty in less than a foot of drilling. The Williamsville granite is pink and medium-grained. In the hand specimen, it has a fresh, sound appearance; it is seemingly composed almost entirely of interlocking grains of feldspar and quartz and has no discernible features suggesting a greater durability than is usually found in rocks with this composition and texture. Microscopic examination, however, reveals a predominance of feldspar grains with more or less regularly distributed and sharply angular masses of quartz (see Fig 1). The pattern assumed by the two minerals in this mode of occurrence is referred to as a "graphic intergrowth," as it bears some resemblance to the cuneiform characters of ancient Persian writing. The other principal constituents are quartz-free feldspars (microcline and orthoclase) and quartz. All of these constituents are in nearly equidimensional grains, ranging up to about 3 mm in length. There are also

Jan 1, 1950

By Leon Merker

FLAME fusion growth of strontium titanate crystals was undertaken to obtain large transparent crystals on which physical data could be gathered. The fact that strontium titanate is a cubic crystal and probably has a high index of refraction indicated that it might be useful in optics. No large boules* of strontium titanate had been synthesized previously, and none have been found as natural occurrences. The flame fusion process, invented by Verneuil in 1904,1 was first applied to grow large crystals of ruby and has since been used extensively to grow crystals of corundum and spinel on a commercial scale. Only during the past nine years has this technique been applied to the growth of large single crystals of other high melting compounds such as rutile,2 mullite,3 and ferrites4 One of several significant advantages of the flame fusion technique over more conventional methods of growing crystals from a melt is that the crystals are grown without the use of melt containers. This fact alone excludes other methods of growing crystals from a melt whenever there are compounds with a melting point near 2000°C or above. Growth of the crystal, similar to that of a stalagmite, takes place inside a circular refractory furnace that does not contact the crystal, Fig. 1. This eliminates a serious source of impurities as well as the likelihood of multi-crystalline solidification along the container walls. The flame fusion technique is particularly advantageous for research because it produces large crystals quickly and at lower cost. A corundum crystal 25 mm long and 12 mm in diam can be grown in 2 to 3 hr. Operating conditions permit observation of the growing crystal during any stage of the process. The various flame patterns and a wide range of oxidation-reduction conditions can be investigated in a relatively short time. It should be pointed out that formation of the foot of the boule is the most critical step in growing an unfractured boule. When the tip of the sintered cone is fused to initiate crystal growth, the original area of fusion should be kept as small as possible so that one crystallite can assume dominance over all the others and propagate as a single crystal. If the boule start happens to consist of several crystals, usually the entire boule also contains several crystals. In many cases these tightly cohering crystals exhibit different crystallographic orientations. Although the basic technique of the original Verneuil process has been retained, refinements in method and burner design have been developed in recent years. For example, boule growth may be initiated on a seed crystal rather than by fusion of a sintered cone. The danger of multicrystalline or twinned boule starts is thus eliminated, and this procedure may also be used to grow boules of predetermined crystallographic orientation. Prior Art: Of the many attempts to produce artificial gem crystals, most early efforts% ere directed toward synthesis of .rubies and sapphires and diamonds. None of these efforts resulted in a process that was commercially practical. Without exception only tiny crystals of corundum were obtained, and those at excessive cost. Verneuil announced his process in 1904; Ravier6 in 1934 presented a detailed description of a commercial boule production plant. Descriptions of the German synthetic stone industry, the process details, and the equipment used have been published by Barnes7 and by Merker.'

Jan 1, 1956

By Clarence Zener

THEORETICAL considerations by one of the authors have led1 to the prediction that the dynamic internal friction of annealed metals has a broad maximum at a certain grain size. This prediction they have veri-fied2 for alpha brass. In the present paper the theory is extended to include the precise manner in which the internal friction varies with grain size on either side of the maximum. New experimental data are pre¬sented to test this extended theory. The physical basis for the type of internal friction that is being investi-gated lies in the interplay between stress and temperature. Just as local fluctuations in temperature give rise to local fluctuations in stress, so like-wise fluctuations in stress give rise to fluctuations in temperature. But temperature gradients give rise to necessarily irreversible thermal cur-rents, and hence to internal friction. The theory for this type of internal friction has been developed quantitatively,3 and has been experimentally verified,4,5 for the particularly simple case of the transverse thermal cur-rents accompanying transverse vibrations. Of more fundamental impor-tance are the intercrystalline thermal currents accompanying all types of vibration. The variation in stress across grain boundaries arises from the elastic anisotropy and at least partial random orientation of the individual crystallites. An exact quantitative treatment of the internal friction due to these thermal currents is of course out of the question. However, much information can be obtained from general arguments.1,6 Thus when the frequency of vibration f is low, or when the grain size d is small, adja-cent grains remain nearly in thermal equilibrium, and vibration proceeds isothermally with little internal friction. Again, when the frequency is high, or the grain size large, the heat flow per cycle is small, the vibration proceeds adiabatically with little internal friction. The internal friction will become a maximum in the transition region. The degree of adiabatic-

Jan 1, 1940