Search Documents

By L. G. Carpenter, D. E. Garrett

Probably the largest single tungsten deposit in the U. S. is one that has yet to produce any tungsten; it is not even listed in tables showing U. S. reserves. This deposit is at Searles Lake, Calif., where the brine contains about 70 ppm WO,. Small though the concentration is, the amount of brine in the lake is so great that it is estimated at 170 million lb of WO3 (8.5 million units), equaling the total of all other known reserves in the U. S. This dry lake is located in the basin formed by the Argus and Slate ranges in the northeastern corner of the Mojave Desert (Fig. 1). It consists of a massive salt body some 35 sq miles in extent, varying in thickness from 0 to 120 ft and containing more than 3 billion tons of salt. A central section of about 8 sq miles is exposed salt; the remaining area is overlain by mud. Except for the exposed sodium chloride (10 to 15 ft thick) the body consists of a very complex and heterogenous mixture of soluble crystals, containing at least eight major phases. It is only about 53 pct solid, the voids being occupied by a dense brine which is the raw material for two chemical companies operating in the valley. The deposit is believed to be made up of salts present in the runoff waters from the last two ice stages. Searles Lakes was the third in a chain of five lakes that received waters from the Owens Valley drainage of the Sierra Nevada Mts. After leaving Owens Lake the waters could flood in succession into the Indian Wells, Searles, Panamint, and Death valleys (Fig. 2). During the first two ice stages of the Pleistocene Epoch most of the waters eventually arrived at Death Valley; consequently the lower 3300 ft of Searles Valley contain only mud

Jan 1, 1960

By Mark A. Ammon

The two most widely used methods of measuring hardness are the Brinell and the scleroscope. In the Brinell method a hardened steel ball is pressed into the steel under a definite load and the area of the resulting depression is measured. The load in kg. per sq. mm. of the area of the depression is taken as a measure of the hardness. Within certain limits the hardness number so determined is independent of the load or the size of the ball. In the scleroscope method a small weight carrying a diamond point is dropped through a glass tube upon the steel and the amount of rebound is taken as proportional to the hard-' ness. In both methods the scale of hardness is an arbitrary one; however, they agree in a comparative may, that is, a steel showing 50 per cent. increase in hardness by the Brinell test mill show approximately 50 per cent. increase in hardness by the scleroscope test. Yet upon consideration of the two methods it appears that, upon a steel which has been carbonized, this should not be the case ; for the scleroscope method gives almost exclusively the surface-hardness, and the condition of the material below the surface has but a slight bearing upon the hardness number. The results given by the Brinell method should, however, be the exact opposite; for the depth of penetration 'of a ball pressed into the steel would be dependent to a large extent upon the condition of the material below the surface. This is particularly obvious when it is considered that the size of the ball ordinarily used in the Brinell method is 1 cm. (about 8 in.) in diameter under a load of 3,000 kg., while the diamond point of the scleroscope is in the neighborhood of 0.01 in. across, fitted in a hammer of about 0.5 oz. weight and dropping from a height of 10 inches.

Jan 1, 1913

INTERNAL The year 1976 was another outstanding year in the operation of the Institute and in the success of its varied activities. Total AIME membership reached 59,773 for a gain of. 6.4 percent. Total revenue increased to $5,111,2 10, up 22.4 percent, and balance sheet assets increased to $8,479,612, up 12.2 percent from the previous year. AIME and its constituent units conducted 30 technical meetings during the year, and attendance was up at most of them. Publications issued by the Constituent Societies continued a healthy growth. During the year 9 new local Sections were established, and at the end of the year the Institute had 150 Sections, with 19 of them overseas. Details on all of these operations are on pages 2 and 3 of this report.

Jan 4, 1977

By Eugene A. Stephenson

In November, 1932, Dr. Lacey, of the California Institute of Technology, presented before the American Petroleum Institute some of the results of his research under Project 371. The investigations described dealt particularly with changes in the physical properties of petroleum that result from the solution of natural gas therein. The solubility of Santa Fe Springs dry gas, containing 87 per cent methane, 8 per cent ethane and 5 per cent propane, had been determined in various crudes at 100' F., and 2000 lb. pressure per square inch as shown in Table 1 and Fig. 1 herewith. Originally the computations were made in terms of cubic feet per barrel, but' for a more uniform basis of comparison the results are also shown as cubic feet of gas2 per cubic foot of oil.

Jan 1, 1935

By E. A. Has, E. Mcl. Tittmann

Double roasting of sinter carrying a high percentage of lead concentrates, gave rise to the problem of removing the sheets of metallic lead formed in the wind boxes. The solution of the problem has been found in the water sealed wind boxes. The metallic lead is granulated and can be removed without seriously interfering with the operation of the machine and eliminates necessity of men going in wind boxes with air guns. THE practice of double sintering the charge for lead blast furnaces, which is now standard throughout the lead smelting industry, has introduced the rather difficult problem of cleaning the wind boxes on sintering machines used for the final pass. Two factors have more recently accentuated this problem: (1) the growing demand of workmen for better working conditions and less arduous labor, and (2) the growing dearth of crude lead ores and the improved grade of lead concentrates demand a charge carrying the maximum percentage of lead. One to 2 pct of such high lead charges (30 to 40) when processed on machines in reasonably good condition will pass through the grates and report in the wind boxes. One-half to three-quarters of this material will be metallic lead reduced by the coke breeze or other fuel mixed with the charge. This lead forms large cakes or chunks which are hard to remove and which substantially increase the time the machine is out of operation for cleaning the wind boxes. A high lead fall can reduce the operating time 30 pct. As a specific example, a 30 ft machine having 63 in. pallets, and equipped with three conventional wind boxes, requires 3 to 4 hr per day for removing the accumulation in the wind boxes when operated as a final pass machine. This same machine when operated on raw charge requires less than an hour per day for cleaning. To eliminate formation of large chunks of lead in the wind boxes of the final pass machines and time lost in cleaning the boxes, R. C. Rutherford of the Chihuahua smelter of the American Smelting and Refining Co., devised and patented* a wind box having a water bath to granulate the lead as it falls from the grate bars. Later, C. H. Harris of the San Luis plant made and patentedt an improvement on Rutherford's device in which the water bath seals the wind box in a manner permitting the latter to be readily cleaned without destroying the vacuum. The first machine to our knowledge to use the water bath box was at the Chihuahua plant along the lines of the Rutherford patent. In 1942, a machine was placed in operation at the El Paso plant which incorporated the features of both Rutherford and Harris. This machine is 40 ft long equipped with pallets 63 x 24 in., and having 4 wind boxes 10 ft 4 in. x 7 ft 2 in. x 51 ft 3 in. in size (fig. 1). The air from the fourth box is returned to the first three, and the gas from the first three discharged to a baghouse. The machine has conventional drive, discharge hopper,

Jan 1, 1951

By H. P. Leighly, J. W. Marx, H. L. Walker

A relationship between recrystallized grain size and prior deformation is predicted from elementary statistical considerations, and reasonable agreement with experiment is obtained. RECRYSTALLIZATION phenomena have received much theoretical and experimental attention, and very adequate discussions of the various mechanisms suggested have been given by Anderson and Mehl,' Cook and Richards,' and Burgers," and others. It suffices to note here that the initial concepts fitted one of two general hypotheses: I—The new crystals are nucleated within microscopic regions at which there is a concentration of internal stress, i.e., volume elements of maximum strain energy. 2—The new crystals have their inception in volume elements of minimum strain energy. In a comprehensive early review of the subject, van Arkel' considered both possibilities and came to the conclusion that hypothesis 2 was inconsistent with the experimental fact that the number of nu-cleations increased with increasing deformation. He suggested that, if allowance was made for a preliminary atomic rearrangement at the points of large internal strain, hypothesfs 1 provided the more reasonable concept. Following the initial observations of Collins and Mathewsonb nd Crussard,Y he systematic X-ray investigations of Cahn' and Guinier and Tennevin" established the existence of a polygonized structure in metals that had been cold-worked, and subsequently annealed, under conditions such that re-crystallization did not occur. This new experimental evidence by no means disproved the first nucleation hypothesis, a fact recognized by both Beck" and Cahn,10 who independently suggested nucleation mechanisms based on the idea that regions of large strain might polygonize before the bulk of the less deformed material. These mechanisms, together with others recently proposed," are dependent upon the prior existence of some degree of polygonization in the deformed material. On the other hand, a critical examination of the published data leads to the supposition that polygonization may not be the necessary precursor of recrystallization, but merely its favored energetic competitor. In regions where the lattice distortion is not too severe, the limited adjustment afforded by polygonization may permit the lattice to drop to a relatively stable low energy state in which the nucleation of a new crystal becomes improbable, even at elevated temperatures. Such structures, of course, might provide a fertile field for the growth of nuclei, if these could be introduced. In regions of concentrated lattice distortion, polygonization alone may not be able to accomplish an adequate strain reduction, and in these volume elements sufficient thermal activity permits the more drastic atomic rearrangement involved in nucleation. Completely polygonized structures are known to withstand extended heating close to their melting points," with no other effect than a slow enlargement of some of the subgrains at the expense of others. Once started, macroscopic recrystallization might be expected to go to completion in a matter of minutes under similar heat treatment. Crussard12 and his coworkers have found that recrystallization may occur in single crystals of impure (about 99.7 pct) aluminum without any detectable prior polygonization. The indication here is that large Cottrell impurity atmospheres inhibit dislocation movement, thus suppressing polygonization to such an extent that the alternative process, recrystallization, dominates the lattice restoration. Experimental studies relating recrystallization directly to stored energy have not, at the present time,

Jan 1, 1954

By Raymond D. Sloan

During 1944, substantial gains were recorded in practically every phase of the petroleum industry in Oklahoma. With the spotlight of activity focused on other states during the more recent years, the production momentum that was achieved in Oklahoma through the discovery and development of such outstanding pools as Oklahoma City, Fitts. and major pools in the Seminole area during the late 1920's and early 1930's was practically spent by the end of 1943. However, with much of the industry's exploratory efforts greatly reduced in Illinois, Indiana and Kentucky, the strong demand for Mid-Continent crude and the optimism created by some discoveries in the state toward the end of 1943, Oklahoma has again become the recipient of much activity and interest, with its 1944 drilling activity, production and refinery runs to stills registering substantial gains over the preceding year. Development and Exploration Since the discovery of the West Edmond pool in April of 1943, with the substquent drilling and development boom, the scene of exploratory activity has shifted from the central. south and east portions of the state to the general trend of the . Granite Ridge, where leasillg and wild-catting were greatly activated within a wide radius of this high subsurface feature. Leasing activity, however, jumped the confines of the Granite Ridge trend and extended into all of the northwestern counties in the state. Seismograph activity at once began following and keeping pace with this shift in the leasing and exploration locale, by the concentration of a large number of seismograph crews in the area. At one time during the year,35 crews were concentrated in Oklahoma, the majority being west of the Granite Ridge and extending into the northwestern counties. To illustrate the increase in geophysical work done in the state during the year, records indicate that 377 crew months were worked in 1944, which is a 21 per cent increase over the 311.5 crew months activated in 1943. With the discovery in 1943 of several encouraging prospects and the finding of West Edmond as an incentive, drilling operations increased some 54.3 per cent, for a total of 1986 completions during the year. This is compared with a figure of 1287 for wells drilled in 1943, an increase of 699 wells. The industry, with a total of 1064 oil producers, enjoyed a success percentage of 53.6 per cent. Gas wells completed were 223, while 699 dry holes were drilled. In 1943, completions included 587 oil wells, 127 gas wells, and 573 dry holes. The number of oil producers completed during the Year was almost double the numher of wells in 1943. Of the total drilling wells completed in the state, 350, or 17.6 per cent, were wildcat operations—an increase of 5.1 per cent over the 194.3 total of 333. The wildcat success percentage was 13.4 per cent, 47 successful wells being completed for an average initial potential of 160 bbl. In the state, 23 gas wells were completed with an average initial production of

Jan 1, 1945

By James W. Halley

"Fine-grained" steels have been standard products for many years. This paper describes an investigation of the effects of some of the more common grain-growth inhibitors used to produce these steels. The properties, response to heat-treatment, and the deoxidation practice necessary to produce "fine-grained" steels have been the subjects of numerous papers. It has been shown that a substantial quantity of aluminum is necessary to produce this type of steel, and it has been indicated that titanium and zirconium produce a similar result. For some time there was a lively argument between those who felt that aluminum refined the grain and those who felt that aluminum oxide was the effective agent. This argument subsided with an apparent victory for those promoting aluminum oxide. Most of the work on grain size has divided steels into two broad classifications based upon McQuaid and Ehn's original carburizing test at 1700°F or some similar test at this temperature. If the steel coarsened at this temperature, it was coarse grained, while if it did not it was he grained. Quantitative data concerning how much a certain amount of aluminum raised the coarsening temperature and affected the properties, all other factors being constant, are very meager. Similar information regarding titanium and zirconium is practically nonexistent. The published information on aluminum yields some quantitative information. Epstein, Nead and Washburn' gave the first quantitative information on the amount of aluminum necessary to prevent grain growth at 1700°F. They showed that the addition of a pound to a pound and a half of aluminum per ton (0.05 to 0.075 per cent) would assure steel that would not coarsen during a McQuaid-Ehn test at 1700°F. Herty, McBride and Houghg reported that a steel containing 0.020 per cent acid-soluble aluminum coarsened between 1742° and 1832°F., while steels containing 0.016 per cent and 0.017 per cent acid-soluble aluminum coarsened between 1652° and 1742°F. compared with similar aluminum-free steels that started to coarsen at 1580°F. Herty3 also showed a marked improvebent in low-temperature notched impact resistance with increasing acid-soluble aluminum up to 0.030 per cent. McQuaid4 compared the coarsening of steels containing 0.011 to 0.204 per cent total aluminum and found a maximum coarsening temperature at 0.098 per cent aluminum. He had no samples between 0.015 and 0.098 per cent aluminum. Houdrement6 found a marked decrease in coarsening temperature with aluminum contents above 0.50 per cent. Kinzel, Crafts and Egan6 found that aluminum and zirconium improved the low-temperature impact resistance of a low-alloy steel, while titanium was detrimental. Sims7 shows that sulphur increases the coarsening temperature and that the maximum coarsening temperature is between 0.04 and 0.06 per cent added aluminum. The fact that the coarsening temperature passes through a maximum with increasing aluminum content appears to be well established. The aluminum content that

Jan 1, 1947

By James W. Halley

"Fine-grained" steels have been standard products for many years. This paper describes an investigation of the effects of some of the more common grain-growth inhibitors used to produce these steels. The properties, response to heat-treatment, and the deoxidation practice necessary to produce "fine-grained" steels have been the subjects of numerous papers. It has been shown that a substantial quantity of aluminum is necessary to produce this type of steel, and it has been indicated that titanium and zirconium produce a similar result. For some time there was a lively argument between those who felt that aluminum refined the grain and those who felt that aluminum oxide was the effective agent. This argument subsided with an apparent victory for those promoting aluminum oxide. Most of the work on grain size has divided steels into two broad classifications based upon McQuaid and Ehn's original carburizing test at 1700°F or some similar test at this temperature. If the steel coarsened at this temperature, it was coarse grained, while if it did not it was he grained. Quantitative data concerning how much a certain amount of aluminum raised the coarsening temperature and affected the properties, all other factors being constant, are very meager. Similar information regarding titanium and zirconium is practically nonexistent. The published information on aluminum yields some quantitative information. Epstein, Nead and Washburn' gave the first quantitative information on the amount of aluminum necessary to prevent grain growth at 1700°F. They showed that the addition of a pound to a pound and a half of aluminum per ton (0.05 to 0.075 per cent) would assure steel that would not coarsen during a McQuaid-Ehn test at 1700°F. Herty, McBride and Houghg reported that a steel containing 0.020 per cent acid-soluble aluminum coarsened between 1742° and 1832°F., while steels containing 0.016 per cent and 0.017 per cent acid-soluble aluminum coarsened between 1652° and 1742°F. compared with similar aluminum-free steels that started to coarsen at 1580°F. Herty3 also showed a marked improvebent in low-temperature notched impact resistance with increasing acid-soluble aluminum up to 0.030 per cent. McQuaid4 compared the coarsening of steels containing 0.011 to 0.204 per cent total aluminum and found a maximum coarsening temperature at 0.098 per cent aluminum. He had no samples between 0.015 and 0.098 per cent aluminum. Houdrement6 found a marked decrease in coarsening temperature with aluminum contents above 0.50 per cent. Kinzel, Crafts and Egan6 found that aluminum and zirconium improved the low-temperature impact resistance of a low-alloy steel, while titanium was detrimental. Sims7 shows that sulphur increases the coarsening temperature and that the maximum coarsening temperature is between 0.04 and 0.06 per cent added aluminum. The fact that the coarsening temperature passes through a maximum with increasing aluminum content appears to be well established. The aluminum content that

Jan 1, 1947

By J. D. Sullivan, Chester R. Austin, J. L. Nunes

It is characteristic of most shales and surface clays that a bloated or vesicular structure is produced by burning to a sufficiently high temperature, usually about 150° to 200°F. above the normal maturing temperature used when making common brick of the same material. Early investi-: gators recognized this phenomenon and attributed it to the release or expansion of gases in the vitrified piece. A number of theories have been advanced on the source of the gas and the manner in which it is evolved, but none has been proved conclusively. T. E. Jackson's1 early theory that bloating was due to oxygen evolved by ferric oxide in forming ferrous oxide or ferrous silicate was never substantiated by - experimental work. Orton2 thought this explanation unlikely, as all clays should bloat at the same temperature, if this were true. He found that clays bloated in the range from IIoo° to 17oo°C. Also, many clays containing iron did not bloat at all, but fused. Orton also stated that oxida- tion of different types of carbon was a source of gas during burning of clay and should be expelled before vitrification was reached. Seger3 said that he had dissolved ferric oxide in glass with no apparent evolution of gas. Matson4 came to the conclusion that ferruginous clays burned ' to vitrification in an oxidizing atmosphere did not have the iron in a ferrous form. According to Wilson,= the gases responsible for bloating might be entrapped air, water, sulphur dioxide, carbon monoxide, oxygen, and hydrocarbons. He spoke of two causes of bloating: (I) incomplete oxidation below the vitrification temperature, and (2) decomposition of compounds and evolution of gases above the vitrification temperature. Decomposition of calcium sulphate was given as the principal example of the latter. Bleininger and Montgomery0 stated that if any time after vitrification began the evolution of gaseous matter was rapid enough so that pressure was produced within the clay, bloating was certain to take place, and a vesicular structure would be formed. They recognized that initial structure, rate of heating, kiln atmosphere, and many other variables affected bloating. Work done by the Emergency Fleet Corporation7 indicated that clays suitable for bloating should be high in compounds of metallic oxides, carbon, sulphur, sodium, potassium, or other equivalent compounds, which either act as a flux or give off gas. Orton2 studied the chemical status of the carbon, iron, and sulphur in clays during various stages of burning, using a Huron shale that bloated under oxidizing or reducing conditions. He found that only a small amount of sulphur remained in the clay and that it could be detected only by dissolving the clay in hydrofluoric acid; i.e., the sulphur was in combination with the silica. orton said that this sulphur was probably in the form of iron sulphide dissolved in the glass phase. The iron sulphide was not broken down by heating, but was dissolved in the basic slag or glass,

Jan 1, 1942

By J. D. Sullivan, Chester R. Austin, J. L. Nunes

It is characteristic of most shales and surface clays that a bloated or vesicular structure is produced by burning to a sufficiently high temperature, usually about 150° to 200°F. above the normal maturing temperature used when making common brick of the same material. Early investi-: gators recognized this phenomenon and attributed it to the release or expansion of gases in the vitrified piece. A number of theories have been advanced on the source of the gas and the manner in which it is evolved, but none has been proved conclusively. T. E. Jackson's1 early theory that bloating was due to oxygen evolved by ferric oxide in forming ferrous oxide or ferrous silicate was never substantiated by - experimental work. Orton2 thought this explanation unlikely, as all clays should bloat at the same temperature, if this were true. He found that clays bloated in the range from IIoo° to 17oo°C. Also, many clays containing iron did not bloat at all, but fused. Orton also stated that oxida- tion of different types of carbon was a source of gas during burning of clay and should be expelled before vitrification was reached. Seger3 said that he had dissolved ferric oxide in glass with no apparent evolution of gas. Matson4 came to the conclusion that ferruginous clays burned ' to vitrification in an oxidizing atmosphere did not have the iron in a ferrous form. According to Wilson,= the gases responsible for bloating might be entrapped air, water, sulphur dioxide, carbon monoxide, oxygen, and hydrocarbons. He spoke of two causes of bloating: (I) incomplete oxidation below the vitrification temperature, and (2) decomposition of compounds and evolution of gases above the vitrification temperature. Decomposition of calcium sulphate was given as the principal example of the latter. Bleininger and Montgomery0 stated that if any time after vitrification began the evolution of gaseous matter was rapid enough so that pressure was produced within the clay, bloating was certain to take place, and a vesicular structure would be formed. They recognized that initial structure, rate of heating, kiln atmosphere, and many other variables affected bloating. Work done by the Emergency Fleet Corporation7 indicated that clays suitable for bloating should be high in compounds of metallic oxides, carbon, sulphur, sodium, potassium, or other equivalent compounds, which either act as a flux or give off gas. Orton2 studied the chemical status of the carbon, iron, and sulphur in clays during various stages of burning, using a Huron shale that bloated under oxidizing or reducing conditions. He found that only a small amount of sulphur remained in the clay and that it could be detected only by dissolving the clay in hydrofluoric acid; i.e., the sulphur was in combination with the silica. orton said that this sulphur was probably in the form of iron sulphide dissolved in the glass phase. The iron sulphide was not broken down by heating, but was dissolved in the basic slag or glass,

Jan 1, 1942

• In 1949 the United States imported 7,400,000 tons of iron ore; Chile, Sweden and Canada, in that order of importance, supplied over 80 pct of this amount. U. S. imports have increased from 3 pct of the total supply in 1940 to 8 pct in 1949. • Mica has been successfully synthesized by scientists of the National Bureau of Standards. quartz, magnesite and bauxite, plus a fluorosilicate compound to act as a crystallizing agent, are heated to 2500°F in a platinum-lined crucible and as the furnace cools mica crystals grow. The key to parallel growth to make sheets is in precision control of temperature. • Inland Steel Co. of Chicago has taken an option to lease from Steep Rock Iron Mines, Ltd., of Canada -- a large undeveloped acreage in the vicinity of Steed Rock Lake, Ontario -- for the purpose of exploring and developing a new iron ore mine. The exploration program is expected to begin at an early date. •A 20-yr test conducted by the U. S. Bureau of Mines with the cooperation of Cleveland-Cliffs indicated that chemically treated timbers last from 2 to 3-1/2 times as long as untreated ones set in the same passageway. Of the three reagents used, zinc chloride gave the best result -- 13.3 yr as compared to 3.8 yr for untreated timber. •Senator Pat McCarran charged that President Truman used a "shotgun approach" to the taxation problem when he accused the mining industry of enjoying excessive depletion exemptions when actually mining taxes should be lowered. He introduced to the Senate a report of the National Advisory Council -recommending a decrease * The country's first graduate program of research and instruction in conservation of natural resources will begin at Yale in September. The Conservation Foundation is supplying $20,000 a year to finance the program. •Felix E. Wormser urged that adequate tariff protection should be provided to offset effects of devaluation on the domestic mining industry in an address before the Colorado Mining Association. He advocates tariffs rather than subsidy legislation, such as S. 2105, for the protection of the lead-zinc miners because the latter would promote inefficiency and "impair our priceless free market." •"It may be startling to realize that for the world's white population the per capita requirements for minerals have multiplied 30 times in 30 yr, or that more minerals have been mined in the last 40 yr than in all prior history." -- Evan Just, in "Mineral Depletion and Metal Supply." •The National City Bank in its monthly letter states that both management and the unions concede that there are too many miners trying to make a living out of the industry for its present market. •On Feb. 3 it was reported that 6000 Anaconda employes in Chile quit jobs in sympathy with striking telephone and electric workers. The government has ordered them back to work on penalty of discharge. It appears that the walkout will not be prolonged in view of the government stand.

Jan 3, 1950

By Samuel Hoyt

This paper gives a short account of plastic deformation as observed in single crystals of zinc, zinc having been selected for the experiments described herein because the phenomena are comparatively so simple and can be studied throughout such a wide range. It is hoped that the paper will serve to show the type of information which studies of single crystals afford and will contribute toward the solution of the general problem of metallic behavior. PRODUCTION OF ZINC SINGLE CRYSTALS The method of Czochralski,1 as modified by vow Gomperz,l was used to produce the crystals studied. The equipment is shown in Fig. 1. Molten zinc is held in a crucible at a temperature which is not far above its melting point, as measured by a pyrometer. A lava disc floats on the melt, and is provided with a central hole about 1 min. in diameter. A glass tube, drawn into a capillary at the lower end, is suspended from a string which is wound up by an electric drive at the speed desired. At the start, the glass capillary is let down into the melt and the hoist is started. The capillary brings up a small quantity of molten metal with it to a point just above the lava disc. At this point, a jet of hydrogen cools it and causes it to crystallize, with the result that a -small crystal forms. As the hoisting is continued, more molten metal is drawn up, in turn to be solidified by the jet of hydrogen. This additional metal continues the growth of the crystal already formed, and a long, cylindrical crystal results. The speed of hoisting used was generally between 0.1 and 0.5 mm. per sec., and the crystals were from 4 to 6 in. long and about 1 mm. in diameter. By varying the conditions, crystals of quite different orientations were obtained and were used in the study of the phenomena to be described.

Jan 1, 1927

By Fred C. Bond and

This paper is a continuation of two earlier papers,12 and presents new data on the grindability of various ores and other materials—the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a new method of measuring the "surface energy" of an ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems. 1. GRindability of Various Ores This part is a continuation of the paper listed as reference No. 1. The method of testing is described in detail in that paper. The sample to be tested is crushed to all through 6 mesh in rolls set at 1/16-in. opening in closed circuit with a screen. Of this sample 700 C.C. is ground dry in a laboratory ball mill under constant conditions of mill speed and ball charge in closed circuit with a screen of the desired size at 250 per cent circulating load. The mill is cylindrical, 12 by 12 in., and rotates at 70 r.p.m. It contains a charge of 285 iron balls weighing 20,125 grams and ranging from 1½ to ¾ in. in diameter. Each test is continued for a sufficient number of periods to establish equilibrium at 250 per cent circulating load, or until the composition of the circulating load is constant for successive periods. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the results are expressed as the net production in grams of screen undersize per revolution of the mill. This is designated as the

Jan 1, 1939

By Fred C. Bond and

This paper is a continuation of two earlier papers,12 and presents new data on the grindability of various ores and other materials—the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a new method of measuring the "surface energy" of an ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems. 1. GRindability of Various Ores This part is a continuation of the paper listed as reference No. 1. The method of testing is described in detail in that paper. The sample to be tested is crushed to all through 6 mesh in rolls set at 1/16-in. opening in closed circuit with a screen. Of this sample 700 C.C. is ground dry in a laboratory ball mill under constant conditions of mill speed and ball charge in closed circuit with a screen of the desired size at 250 per cent circulating load. The mill is cylindrical, 12 by 12 in., and rotates at 70 r.p.m. It contains a charge of 285 iron balls weighing 20,125 grams and ranging from 1½ to ¾ in. in diameter. Each test is continued for a sufficient number of periods to establish equilibrium at 250 per cent circulating load, or until the composition of the circulating load is constant for successive periods. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the results are expressed as the net production in grams of screen undersize per revolution of the mill. This is designated as the

Jan 1, 1939

By Charles Legrand

The power plant of the Burro Mountain Copper Co. is located near Tyrone, N. M., at 5,950 ft. elevation. It is interesting because it uses the largest stationary Diesel engines in the United States. The general layout of the plant is shown in Figs. 1 and 2. The building is of steel-frame construction with hollow-tile walls and corrugated-iron roof; the floor is concrete and all windows have steel frames, making a fireproof building. The building is made to accommodate one more electric generator unit which is being installed; also two 4,000-cu. ft. air compressors direct-connected to three-cylinder engines with the same size cylinders as the electric units. The power plant consists of two 815-kva., 60-cycle, three-phase, 6,600-volt, 180-r.p.m. generators, direct-connected to five-cylinder, two-cycle Diesel engines; the necessary circulating pumps for cooling water, cooling towers and oil storage tanks. A portion of the power is used in the same building as the generating units to run one of two 200-kw. rotary converters delivering 260-volt direct current, and a 2,500-cu. ft. air compressor, delivering air at 95 lb. pressure, direct-connected to a 400-hp., 6,600-volt, three-phase synchronous motor. The remainder of the power is used to run a 1,500-ton concentrating mill 3 ½ miles from the power house, various hoists, pumps and motors about the mines and the lighting and water-works of the town of Tyrone. The direct current is used for electric traction in the mine, also to run hoists and motors that were installed before the new power plant was built. Due to the large hoists that take starting peaks of 250 kw. and the 10-ton electric locomotive that takes at times 150 kw., the load is extremely variable, as shown in. Fig. 3.

Jan 9, 1916

By Sir Robert Hadfield

(New York Meeting, February, 1913.) THE Hadfield method of producing sound steel ingots has been the subject of a paper 1 read before the Iron and Steel Institute, so that it will be unnecessary to describe it fully here. The object of the method is to make possible the production of steel ingots in which the pipe is almost entirely obliterated, and it is applicable particularly to the production of sound ingots, from which good rails could be rolled. The method in brief consists in casting the ingots on cars, usually with the small end down. Each ingot mold is provided with a sand top, rammed up in the well-known manner. After the mold is filled to the desired height with steel, a layer of slag about 0.5 in. thick is placed upon it and the balance of the mold is then filled with charcoal. Then, through suitable piping, an air blast is directed in numerous jets upon the charcoal, which is burned thereby, the combustion supplying additional beat to the top of the ingot, which helps to keep the top fluid and to retard its solidification, while the lower parts are rapidly losing heat by its transfer to the mold. By-one plan the ingots are cast in molds placed upon bogies, movable trucks, or platforms, in the position A, Fig. 1. The ingots are cast vertically on bogies, say four or more ingots on each bogie, as may be found most convenient, and the upper surface of the steel is maintained in a molted condition during the transit of the ingots from the casting pit to the stripper. This is effected by a series of air pipes, for example, three in number, with jets or holes on the under surface of such pipes, placed preferably horizontally, arranged in such a manner as to cause jets of air to impinge on the upper surface of the ingots. These holes or jets are made throughout the entire length of the overhead pipes, the length of such pipes being

Jan 4, 1913

By Sir Robert A. Hadfield

The Hadfield method of producing sound steel ingots has been the subject of a paper read before the Iron and Steel Institute, so that it will be unnecessary to describe it fully here. The object of the method is to make poseible the production of steel ingots in which the pipe is almost entirely obliterated, and it is applicable particularly to the production of sound ingots, from which good rails could be rolled. The method in brief consists in casting the ingots on cars, usually with the small end down. Each ingot mold is provided with a sand top, rammed up in the well-known manner. After the mold is filled to the desired height with steel, a layer of slag about 0.5 in. thick is placed upon it and the balance of the mold is then filled with charcoal. Then, through suitable piping, an air blast is directed in numerous jets upon the charcoal, which is burned thereby, the combustion supplying addi, tional heat to the top of the ingot, which helps to keep the top fluid and to retard its solidification, while the lower parts are rapidly losing heat by its transfer to the mold. By one plan the ingots are cast in molds placed upon bogies, movable trucks, or platforms, in the position A, Fig. 1. The ingots are cast vertically on bogies, say four or more ingots on each bogie, as may be found most convenient, and the upper surface of the steel is maintained in a molten condition during the transit of the ingots from the casting pit to the stripper. This is effected by a series of air pipes, for example, three in number, with jets or holes on the under surface of such pipes, placed preferably horizontally, arranged in such a manner as to cause jets of air to impinge on the upper surface of the ingots. These holes or jets are made throughout the entire length of the overhead pipes, the length of such pipes being

Jan 1, 1914

By M. B. Bever, A. B. Michael

The solidification of aluminum-rich aluminum-copper alloys was investigated for different solidification rates. The measured amounts of nonequilibrium eutectic were compared with the amounts calculated on the assumption of no diffusion in the solid. The morphology of the eutectic was studied and dendritic spacings were measured. Compositions of the cored primary solid solutions were determined by quantitative autoradiography after activation of the solute copper by neutron irradiation. CONSIDERABLE progress has been made in recent years toward an understanding of the solidification of metals. This is especially true for the factors involved in nucleation, the controlled growth of metal crystals from melts, and various aspects of the freezing of ingots and castings. Many features of the solidification process, however, are not understood adequately and much further work is required. In the research reported here the solidification of a series of aluminum-rich aluminum-copper alloys was investigated. Different degrees of deviation from the idealized case of equilibrium solidification were attained by varying the rate of solidification. Thermal analysis and microscopic examination were supplemented by lineal analysis and autoradiography. The latter required the use of radioactive tracers and was adapted to the quantitative determination on a microscale of concentrations of copper dissolved in aluminum. The tracers were produced in situ by activating the copper with neutrons. These techniques permitted a correlated interpretation of the temperature-time history, the amounts of nonequilibrium eutectic and the general morphology of the alloys, and yielded quantitative data on microsegregation. Nonequilibrium Solidification In the general case of the solidification of a solid solution in accordance with the phase diagram, the composition of the coexisting liquid and solid must change continuously. This change requires diffusion, which at best remains incomplete in the solid during solidification. The resulting inhomogeneity of the solid solution crystals is well-known as coring, dendritic segregation, or microsegregation. The generally accepted analysis of coring assumes that, 1—no diffusion occurs in the solid, 2—diffusion is complete in the liquid, and 3—the composition of the solid formed on cooling through any infinitesimal temperature interval is given by the solidus of the phase diagram. On this basis, In this equation m designates mass, x designates the concentration of solute and the subscripts L and S refer to the liquid and solid phases, respectively; the subscript o indicates the initial state, in which the liquid is identical with the entire system. Eq. 1 or its equivalent has been derived repeatedly'-7 and an analogous equation, known as Rayleigh's equation, has been used for distillation. The assumptions on which Eq. 1 is based do not include an infinitely fast cooling rate as sometimes stated. In fact, Olsen and Hultgren %ave shown by experiment that very high solidification rates suppress coring, presumably by preventing diffusion in the liquid and by the effect undercooling has on the composition of the nucleus. Coring thus occurs at rates of cooling which are too fast for a close approach to equilibrium in the solid and too slow to suppress diffusion in the liquid and to cause marked undercooling. If the liquidus and solidus approximate straight lines, Eq. 1 simplifies to The fraction of liquid present at any temperature during nonequilibrium solidification can be calculated from Eqs. 1 or 2. By the lever relation it is

Jan 1, 1955

By N. K. Chen, R. Maddin

In the extension of molybdenum single crystals at room temperature, the slip planes were found to be of the type (1101; the slip direction <111>. Theories of plasticity of body-centered cubic metals have been examined, and an explanation based upon planes of highest atomic density seems plausible to explain the plastic behavior of molybdenum single crystals. IN body-centered cubic metals, slip has been reported to occur on several planes; these are of the type {110), {112), and (123). Andrade has correlated&apos; the operative slip planes in body-centered cubic metals with the testing temperature relative to the melting point. In this correlation, if T is the absolute temperature at which slip takes place and Tm the absolute melting point, then the acting slip planes in body-centered cubic metals may be arranged as shown in Table I. However, deviations from this correlation have been reported in iron and iron-silicon alloys2 and also in molybdenum deformed at a temperature around 2400°C." In the case of iron and other body-centered cubic metals or alloys in which all three slip planes have been reported to be active at any one temperature, the crystallographic mechanism of slip is not well understood. Numerous investigators in this field have assumed that the resolved shear stress is a deciding factor. Such considerations were given by Gough in his experiments with repeated torsion of iron single crystals4 and recently by Opinsky and Smoluchowski in their study of iron-silicon alloys," and will be dealt with later in this report. A third possibility is that slip lines in body-centered cubic metals may be formed by alternate slip on nonparallel (110) planes and not by slip on any plane of higher indices. This was advanced by Elam in the case of ß brass." Since (1101 planes are planes of highest atomic density in the body-centered cubic structure, this hypothesis would be in accordance with the plastic behavior of metals in other systems, namely, face-centered cubic and hexagonal close-packed. Experimental evidence in support of this hypothesis is lacking. Nevertheless the work of Barrett, Ansel, and Meh12 has definitely demonstrated that the slip resistance on {110} planes in iron is very much smaller compared with that on (112) and (123) planes. In the present investigation, molybdenum single crystals were carefully documented as to the operative slip planes and lattice reorientations after plastic extension at room temperature. In three crystals studied, (110) planes were found to be active invariably rather than the (112) planes, which were previously reported for molybdenum at this temperature&apos; and predicted by Andrade&apos;s theory.&apos; In two other cases (112) and (123) planes seemed to operate together with (110) planes as active slip planes. However, it is believed, after careful analysis of crystallite and lattice rotations, that slip on (112) and (123) planes may be spurious. Particular reference will be made to the formation of asterism, lattice rotation, and crystallite rotation in an attempt to show that slip apparently observed on {1121} and (123) planes is actually slip on nonparallel {110} planes. Materials and Treatment Sintered molybdenum rods ? in. in diam, obtained from the Fansteel Metallurgical Co., were reported to have a purity of 99.9 pct.* One specimen, Mo-13, ¼ in. in diam, was supplied by Westinghouse Electric Corp. Single crystals were prepared, using the technique devised by Chen, Maddin, and Pond." Mo-13 was ¼ in. in diam x 7 in. long with a reduced gage section of 0.200 in. in diam x 3 in. long. The center of

Jan 1, 1952