Search Documents

By C. L. Dake

Iron is much more soluble in the ferrous than in the ferric form. Where, as in the case of the ferrous silicates and. the sulphides, the iron is already in the ferrous form, it may go at once into solution and be removed, upon the breaking down of the parent rock. If in the ferric form, it must first be reduced; usually by the decay of organic matter, the demand of the decaying carbonaceous matter for oxygen being so great that the latter is abstracted from the ferric compounds and the iron is thereby reduced and rendered soluble. The iron may go into solution as the sulphate, or in the presence of excess CO2 as ferrous carbonate. It is probably soluble as salts of the organic acids.' Recent work indicates that these are important in the formation of bog ores.2 There is considerable variety of opinion concerning the behavior of these organic compounds.3 The secretions about the roots of plants and trees also cause the solution and removal of iron and a consequent bleaching of the soil,4 While the matter is not yet well understood, we can probably say definitely that the so-called organic acids are a group of colloids which possess slightly acid properties, and the salts of which are partly soluble and partly insoluble.5 Their iron salts readily change from the ferrous to the ferric form, and their solubility is greatly modified by the presence of ammonia.

Jan 1, 1916

By C. Hirayama

THIS investigation was undertaken to determine some of the factors contributing to the embrittle-ment of glass-coated silver wire on heat treatment. The materials used in this investigation were 22 and 23 AWG silver wires obtained from Handy and Harman as "fine quality, soft temper." A wet analysis of one sample showed 99.8 pct Ag. The 23-gage wire was covered with a double layer (2.5 mils thick) of electrical grade fiber glass (aluminum borosilicate glass containing a relatively high concentration of calcium, and a very small amount of

Jan 1, 1960

By W. J. Babyak, J. M. Sheehan, H. W. Paxton

THE- solubility of hydrogen and deuterium in solid niobium up to I-atm pressure has been established bv a number of workers.1-5 X-ray examination at room temperature of specimens reacted in hydrogen at high temperatures from 300° to 1000°C shows the presence of two phases—a bcc phase (a) based on the niobium lattice and with an u0, increasing from 3.30A for Nb to 3.32Afor NbHo.L, and an orthorhombic phase6n = 4.84A, h=4.90A, c =

Jan 1, 1960

By Reed W. Hyde

SOME information has been published on the sulphur dioxide concentration of gases from Dwight-Lloyd machines sintering lead ores but most of this relates to the customary practice in which the charge is relatively high in lead and is sintered in two passes over the machine. It is thought, therefore, that the following observations on sintering in one pass a low-lead, low-sulphur charge may be of interest. The data were obtained in sintering lead sulphide flotation concentrates mixed with minus 20-mesh oxide ore, the mixture carrying 16.8 per cent Pb and 5.3 per cent S. No returns were used because of the limited amount of sulphur available as fuel, but the mixture pelletized readily to make a satisfactorily permeable bed on the sintering machine. As there was a possibility that the SO2 might be utilized, a series of runs was made to determine the concentration of SO2 in the gases at different points along the wind box, and the effect on this concentration of changes in the wind-box vacuum. Several runs each were made with vacuums (as measured in inches of water at the wind box) of (1) 2 to 1 3/4 in., (2) 4 to 3 1/2 in. and (3) 6 to 5 1/8 in. The averages of the determinations from each series are platted on the graph (Fig. I). The vertical scale shows the percentage by volume of SO2 (as determined by the Reich method), and the horizontal scale shows the time expressed as percentage of the total sintering time. Sintering was considered to be complete when no SO2 could be detected in the gases. In all cases the depth of bed was 4 1/2 in. and the weight of dry charge per square foot of hearth area was 45.2 lb. Other data are given in the table. The volume of gases corresponding to the several points along the wind box at which SO2 determinations were made could not be measured, but has been calculated from the SO2 content and sulphur elimination on the assumption that the volume is uniform throughout the sintering period. This is not strictly true, as with a given vacuum the volume will usually drop slightly toward the middle of the period and increase toward the end. However, this assumption is a reasonable approximation. Several interesting features are brought out by these data. In general, the published data on SO2 concentration in sintering under ordinary conditions show a high SO2 concentration in the early stages followed by a rapid decrease in concentration and with relatively little SO2 in the gases from the last half or third of the operation. In other words, the greater part of the sulphur elimination is obtained in the first third or half of the period. In these runs, the 6-in. vacuum, which approximates the usual operating condition, gives a curve that follows this customary pattern. Maximum SO2 concentration is obtained 2 ½ min. after

Jan 1, 1942

ONE HUNDRED AND FOURTEENTH MEETING OF THE INSTITUTE, MONDAY, FEBRUARY 19, TO THURSDAY, FEBRUARY 22, INCLUSIVE, 1917 Committee on Arrangements DAVID H. BROWNE, Chairman LAWRENCE ADDICKS Louts D. HUNTOON E. MALTBY SHIPP PERCY E. BARBOUR H.A. MEGRAW BRADLEY STOUGHTON GEORGE D. BARROW _ THOMAS T. READ EDWARD B. STURGIS KARL EILERS BURR A. ROBINSON ARTHUR L. WALKER F. T. RUBIDGE Summarized Program MONDAY, FEBRUARY 19 9:00 a.m. to 5.00 p.m. Registration at Institute Headquarters. , 10.00 a.m. Simultaneous Sessions on Geology and on Metallography.

Jan 2, 1917

By Reed W. Hyde

SOME information has been published on the sulphur dioxide concentration of gases from Dwight-Lloyd machines sintering lead ores but most of this relates to the customary practice in which the charge is relatively high in lead and is sintered in two passes over the machine. It is thought, therefore, that the following observations on sintering in one pass a low-lead, low-sulphur charge may be of interest. The data were obtained in sintering lead sulphide flotation concentrates mixed with minus 20-mesh oxide ore, the mixture carrying 16.8 per cent Pb and 5.3 per cent S. No returns were used because of the limited amount of sulphur available as fuel, but the mixture pelletized readily to make a satisfactorily permeable bed on the sintering machine. As there was a possibility that the SO2 might be utilized, a series of runs was made to determine the concentration of S02 in the gases at different points along the wind box, and the effect on this concentration of changes in the wind-box vacuum. Several runs each were made with vacuums (as measured in inches of water at the wind box) of (1) 2 to 1 1/3 in., (2) 4 to 3 1/2 in. and (3) 6 to 5 1/8 in. The averages of the determinations from each series are platted on the graph (Fig. I). The vertical scale shows the percentage by volume of SO2 (as determined by the Reich method), and the horizontal scale shows the time expressed as percentage of the total sintering time. Sintering was considered to be complete when no S02 could be detected in the gases. In all cases the depth of bed was 4 ½ in. and the weight of dry charge per square foot of hearth area was 45.2 lb. Other data are given in the table. The volume of gases corresponding to the several points along the wind box at which S02 determinations were made could not be measured, but has been calculated from the S02 content and sulphur elimination on the assumption that the volume is uniform throughout the sintering period. This is not strictly true, as with a given vacuum the volume will usually drop slightly toward the middle of the period and increase toward the end. However, this assumption is a reasonable approximation. Several interesting features are brought out by these data. In general, the published data on S02 concentration in sintering under ordinary conditions show a high S02 concentration in the early stages followed by a rapid decrease in concentration and with relatively little SO2 in the gases from the last half or third of the operation. In other words, the greater part of the sulphur elimination is obtained in the first third or half of the period. In these runs, the 6-in. vacuum, which approximates the usual operating condition, gives a curve that follows this customary pattern. Maximum S02 concentration is obtained 2 ½ min. after

Jan 1, 1942

By F. Rosenblum

An on-stream particle size analyzer (PSA) based on the sedimentation principle has been developed to the commercial prototype stage and tested at a concentrator. The current instrument gives a direct reading of the weight % finer than any two sizes, although the capability exists for providing a complete size distribution through the sieve and sub-sieve range. The readings obtained at intervals of about 10 minutes are derived from 0.5-L samples of slurry cut from the monitored stream. The accuracy of the PSA meets the requirements of process control.

Jan 1, 1984

By P. Shahinian, M. R. Achter

P. Shahinian and M. R. Achter (U.S. Naval Research Laboratory)—We should like to point out another instance where concentration of impurities in grain boundaries led to an embrittlement. In this case an impure nickel (99.8 pct) developed many more in-tergranular cracks during creep in a nitrogen atmosphere than in vacuum.5 In comparison high-purity nickel (99.99 pct) exhibited a much smaller atmosphere effect. We concluded that the interartion of the nitrogen with nitride-forming impurities concentrated at grain boundaries promoted inter-granular cracking.

Jan 1, 1965

By S. W. Ihle, L. J. Warren

A sample of garnet from the scheelite ore body on King Island, Tasmania, Australia, was upgraded and ground to produce an ultrafine portion suitable for micro-electrophoresis. X-ray and chemical analysis identified the garnet as andradite with some admixed grossular. At neutral pH the garnet particles were negatively charged, their zeta potential becoming rapidly more negative with increasing pH. An iso-electric point was found at pH 3.5. The effects on the zeta-potential of various electrolytes, hydrolyzable metal ions, and flotation collectors were also studied.

Jan 1, 1976

By T. M. Dr. Drown

(Read at the Philadelphia Meeting, February, 1878.) ZINC is, as is well known, very brittle at a temperature of about 210° C. (410° F.), and may then be readily pulverized in a mortar. By sifting it may be obtained of uniform grain. I have been accustomed to prepare products passing through 40, 60, and 80-mesh sieves, and also by bolting through a fine handkerchief. The principal analytical uses to which I have hitherto applied this material are to the reduction of iron directly from the ore by heating it with the pulverized zinc, and the reduction of ferric to ferrous compounds in solution. In the first case the pulverized ore, 0.5 gram or less, is intimately mixed with about ten times its weight of the pulverized zinc (the finer the zinc the better), in a porcelain crucible, and this mixture is covered with about the same amount of zinc. The crucible is then heated at the top of the flame of a Bunsen burner, at a dull red heat, for about ten minutes. The crucible should not be covered. When cool, the crucible, with its contents, is placed in a flask treated with hot dilute sulphuric acid, and brought quickly to a boil. The zinc and reduced iron are dissolved in a few minutes and the flask is then tightly corked and allowed to cool. When cool, the iron is directly titrated by potassium permanganate.

Jan 1, 1878

By Enid C. Plante

INTRODUCTION To extend our knowledge of the flotation behavior of sulphide minerals, the response of the following minerals to ethyl xanthate as collector was studied by captive bubble and cylinder flotation tests: antimonite (Sb2S3), arsenopyrite (FeAsS), covellite (CuS), marcasite (FeS2), orpiment (As2S3), pyrrhotite (FeS) and tetrahedrite (4CU2S, Sb2S3). Lollingite (FeAs2) was also examined to determine if its behavior could be correlated with that of pyrite or marcasite (FeS2). EXPERIMENTAL METHOD Mineral for Flotation and Contact Tests Mineral was prepared in the manner already described' and its behavior both freshly ground and "oxidized" was studied. Tests in which the mineral was allowed to oxidize for various periods showed that a uniform response to xanthate was reached in two days or less. Oxidation Products The soluble oxidation products from most of the above minerals were measured and their effect on the flotation of the mineral studied. The mineral samples were wet ground to minus-52 mesh and deslimed, and 20 g of this material placed in 200 ml of distilled water of a measured pH value, and C02 free air bubbled through each suspension at a constant rate (about 1 bubble/sec) for 5 days. It has been shown1 that the size of the mineral is unimportant in the rate of formation of oxidation products and that probably the supply of oxygen to the mineral is the rate-determining step. At the end of 5 days the pH value of the supernatant liquid was measured again, the mineral filtered off and the soluble products determined. Methods for estimation of sulphur acids, ferrous and ferric iron and copper have already been described.1 No satisfactory method was found for antimony. Arsenic was estimated as the arsenate.2 FLOTATION OF "UNOXIDIZED" MINERALS WITH ETHYL XANTHATE AS COLLECTOR Fig I to 3, 4, 6, show the effect of alkali and cyanide as depressants for the minerals with 25 mg potassium ethyl xanthate per liter as collector at 35°C. Wark and Cox3 have shown that with ethyl xanthate as collector, galena, pyrite and chalcopyrite show a greater tolerance to cyanide and hydroxyl ions at room temperature than at 35°C. Covellite (Fig I), marcasite (Fig 2) and pyrrhotite (Fig 3) behave similarly. The independence of the curves for pyrrhotite at 35°C with respect to cyanide

Jan 1, 1947

By E. V. Potter

For a nurnber of years, it has been known that manganese made by electro-deposition under certain conditions is ductile while under other conditions it is very brittle. The ductile metal is gamma manganese normally stable only between 1100 and 1138°C1; the brittle metal is alpha manganese, stable up to 727OC. The ductile metal is not stable, but gradually changes to the brittle form; the time required to complete the transfornlation is about 20 days at room temperature. Other observations have indicated that the transformation is completed in 10 to 15 min. at about 125°C, while at — 10°C, no appreciable change occurs in 9 months. The properties of gainma and alpha Illanganese in the pure state are ordinarilj difficult to determine because the gamma structure cannot be retained by normal quenching procedures and alpha manganese is so brittle, it is difficult to obtain specimens free from flaws. In a recent investigation2 some properties of gamma and alpha manganese were determined by studying the ductile electrolytic metal and determining the changes in its properties as it transformed to the brittle alpha form. These investigations provided an excellent opportunity for following the progress of the transition and studying its mechanism. The results of a series of such investigations are reported in this paper. Procedure Various properties of manganese were determined starting with the metal in the original ductile gamma form and following the subsequent changes in its properties as the metal transformed to the brittle alpha form. These observations were made at various temperatures, the data providing information regartling the mechanism of the transformation as well as the effect of temperature 011 the transition rate. Structure and resistivity values gave the most significant results, so this paper is concerned primarily with them. The structure was studied microscopically as well as by X ray diffraction. The resistivity was determined on strips of the metal by measuring the potential drop across a given length of the specimen. Current was passed through the specimen by wires soldered to its ends, and the potential connections were made by wires looped around the specimen near its center. The current was determined by the potential drop across a standard resistor connected in series with the specimen, the potential drop being measured on a potentiometer. In the temperature range from room temperature to 100°C an ordinary drying oven was used to heat the specimen. This was entirely satisfactory except at 100°C, where the time required to heat the specimen was long compared to the transition time, making the initial section of the resistivity curve unsatisfactory. To overcome this limitation, at 100°C and higher a thermostatically controlled oil bath was used to heat the specimens. The block on which the specimen was mountetl was plunged into the hot oil at the start of each test. The heating time was thereby reduced from 5 min. to about 6 sec, and dependable resistivity values could be obtained through 160°C. At this point the whole transition, including the warm-up time for the specimen, required only about 20 sec and it was not considered worth while trying to extend the temperature range further. Aside from the heating problem, the problem of making a sufficient number of accurate resistivity determinations became more and more difficult as the temperature was raised. Using the manually operated potentiometer, 100°C was about as far as it was possible to go. At this temperature and above, a self-balancing photoelectric recording potentiometer was used. Its response was quite rapid, and it proved to be entirely satisfactory all the way through 160°C, where the tests were stopped because of the specimen heating problem rather than any limitation of the potentiometer recorder. The metal used in these tests was prepared at the Salt Lake City laboratory of the Bureau of Mines. The method of preparation is discussed in a paper by Schlain and Prater.3 The sheets were about 2 3/8 by 5 3/16 in. and varied from 10 to 16 mils in thickness. They could be cut readily into pieces suitable for the various tests. X ray and microstructure determinations were made on pieces about 1/8 to 1/4 in. wide and about 1 in. long, while resistivity measurements were made on strips as long as possible and about 55 in. wide. The thickness of each sheet was not uniform over all its surface. This had no bearing on the X ray and microstructure determinations, but sections as nearly uniform and free from flaws as possible were chosen for the resistivity determinations. The gamma manganese was electro-deposited at 30°C, the time of deposition ranging from 5 to 12 hr for each sheet. Whenever possible, the tests were started directly after the metal was stripped from the cathode; otherwise the sheet was placed immediately

Jan 1, 1950

By Lawrence Adler

Any design of a mine roof in bedded deposits which ignores differential deflections at the supports can quickly lead to dangerous overstressing. As illustrated by the typical case presented on page 1029, if one support deflects only 0.1 in. more than its neighbor, stresses 50 pct higher than anticipated will result. Previous studies1-3 have assumed that the mine roof acts like a beam clamped at both ends, with no deflection or slope4 at the supports (Fig. 1). Essentially this assumes:5,6 [BA = OD = 0 and dA = dB = 0.]

Jan 10, 1959

In the Texas Panhandle 277 oil wells and 60 gas wells were completed during 1942, as compared with 647 oil and 52 gas wells completed in 1941. Fourteen dry holes were drilled in the Texas Panhandle in 1942, of which five were wildcats, resulting in four failures and one gas-field discovery in Sherman County; the latter being Hazy-Herrington-Marsh No. I Bivins completed for 5,600,000 cu. it. ol gas from 2989 to 3226 feet. During the year 1942 the Texas Panhandle produced, by counties, the following quantities of oil:

Jan 1, 1943

In the Texas Panhandle 277 oil wells and 60 gas wells were completed during 1942, as compared with 647 oil and 52 gas wells completed in 1941. Fourteen dry holes were drilled in the Texas Panhandle in 1942, of which five were wildcats, resulting in four failures and one gas-field discovery in Sherman County; the latter being Hazy-Herrington-Marsh No. I Bivins completed for 5,600,000 cu. it. ol gas from 2989 to 3226 feet. During the year 1942 the Texas Panhandle produced, by counties, the following quantities of oil:

Jan 1, 1943

Engineering Experiment Station, University of Arkansas, Fayetteville, Ark. W N Gladson, Dean and Director The Engineering Experiment Station has published a number of bulletins, only a few of which are of particular interest in this directory: Bulletin 3, Arkansas coal or oil for domestic heating; 4, Road materials of Arkansas, 5, A study of Arkansas coals, 6, Portland cement materials in Arkansas; 11, Natural gas versus Arkansas coal for house heating. Circular 3, Short cuts to combustion efficiency with natural gas Address the Engineering Experiment Station for any of these publications.

Jan 1, 1933

By John Bonar

A switch to refractory-type slurry pump linings has significantly reduced maintenance costs arising from liner failure at a Missouri lead mill. The pumps routinely handle a slurry consisting of 79 to 81% solids with occasional tramp iron, and are subjected to intense abrasion which previously wore out rubber liners in anywhere from three days to two months. Average liner life at the 1.5-million-t/y (1.6-million-stpy) operation was 30 days. Experimentation with mild steel liners and even manganese steel liners failed to extend liner life beyond two months.

Jan 3, 1978

By J. B. Clark, A. S. Yue

The zone-melting technique can be adapted for the de-termination of the eutectic composition in complex metal systerrzs. The application of this method is demonstrated in a simple eutectic system, Mg-AE, in which the eutectic composition is known and in a complex ternary system, Mg-Al-Zn, in which the literature is uncertain as to the composition of the ternary eutectic. The advantages and limitations of this unique approach for the determirution of the eutectic composition are discussed. ThE eutectic composition in phase diagrams is usually determined by thermal analysis of a series of arbitarily selected alloy compositions. The temperatures of the liquidus and eutectic arrests for each alloy are plotted and the eutectic composition is estimated by extrapolation to the entectic temperature of the curve formed by the liquidus arrest temperatures for the series of alloys. Although this approach readily yields the eutectic temperatures, several dekrminations are needed to estimate the eutectic composition, even in a simple system. In a complex ternary system, a great many determinations are often necessary to estimate, even approximately, the ternary eutectic composition. Thus, the conventional method is inherently tedious and time consuming. The application of zone melting provides a relatively efficient method of determining the eutectic composition.' As an illustration, consider the zone melting of an alloy composition C, in the simple eutectic system A-B, shown in Fig. 1, under the ideal conditions of infinitely rapid diffusion in the liquid, no diffusion in the solid, and ease of nucleation of both phases. As the zone moves along the bar, the composition of the zone is enriched by solute rejected during the freezing of the a phase and the zone composition approaches the eutectic composition CE.Once the zone composition attains the lowest melting composition, i.e., the eutectic composition, it remains at this composition as the zone moves along the bar and finally freezes as such at the end of the bar. Chemical analysis of the end of such a zone-melted bar then should yield the eutectic composition CE of the system A-B. A corresponding analysis can be made for a ternary eutectic system. Under the ideal conditions noted above, only one pass of the molten zone is required to yield the eutectic composition. Experimentally, however, a solute-rich layer forms at the solid-liquid interface2 and the composition of the zone does not attain the eutectic composition as rapidly or as uniformly as in the ideal case outlined above. But with agitation of the melt, the ideal conditions can be approximated experimentally. Also, as shown below, zone melting permits a cumulative build-up of the solute at the end of the bar to the eutectic composition. The purpose of this paper is to demonstrate this unique method for determining the eutectic composition. The method is here applied to two systems: first, to the binary Mg-A1 system, in which the composition is well established, and second, to the complex Mg-Al-Zn system in which there is doubt concerning the composition of the ternary eutectic. EXPERIMENTAL PROCEDURE The zone-melting apparatus used in this study is described in detail elsewhere.3 Briefly, the binary alloy rods (5/8 in. in diam and 9 in. long) and the ternary alloy rods (5/8 in. in diam and 6 in. long), with the compositions given in Table I, were zone

Jan 1, 1962

By A. M. Sarem

For the performance prediction of multiphase oil recovery processes such as steam stimulation, there is an acute need for three-phase relative permeability data. No fast and simple experimental technique, such as the unsteady state method proposed by Welge for two-phase flow, is available for the three-phase flow. In this paper, an unsteady - state method is presented for obtaining three-phase relative permeability data; this method is as fast and easy as Welge's method for two - phase flow. Analytical expressions are derived by extension of the Buckley-Leverett theory to three-phase flow to express the saturation at the outflow face for all three phases in terms of the known parameters. It is assumed that the fractional flow and relative permeability of each phase are a function of the saturation of that phase. Other simplifying assumptions made include the neglect of capillary and gravity effects. The effect of saturation history upon relative permeability is acknowledged and attainment of similar saturation history in laboratory and field is recommended. The required experimental work and computations are simple to perform. The test core is presaturated with oil and water, then subjected to gas drive. During the test, required data are the rates of oil, water, and gas production, together with pressure drop and temperature. The ordinary gas-oil unsteady-state relative permeability apparatus can be readily modified to measure the required data. The proposed technique was applied to samples of a Berea and a reservoir core. The effect of saturation history upon relative permeability was studied on one Berea core. It was found that increase in initial water saturation has a similar effect upon three-pbase relative permeability as it does in two-phase flow. INTRODUCTION In the light of increasing demand for three-phase relative permeability data for predicting the performance of thermal and other multiphase-flow recovery processes, a simple and accurate method of experimental determination of such data is extremely desirable. Leverett and Lewis 1 described the simultaneous flow method of obtaining three-phase relative permeability data. However, Caudle et al.2 reported that this method is very time consuming and cumbersome. Corey3 proposed calculating the three-phase relative permeability from measured krg data. Corey's theory is based on simplified capillary pressure curves,4 assuming a straight line relationship between I/Pc2 and saturation. Also, Corey's method assumes a preferentially water-wet system. The simplest and quickest method of obtaining three-phase relative permeability data is the unsteady-state method where, for instance, oil and water are displaced by gas. However, in such a test the correlation of average saturation with relative permeability does not give a valid relationship because the rates of oil, water and gas flow in the sample change continuously from the upstream to downstream end. This difficulty in calculating valid relationships was solved by Welge for two-phase flow by deriving an expression for determining the outflow face saturation from Buckley and Leverett frontal advance equations.5,6 In this paper, relations are established to determine the outflow face saturation and relative permeability to all phases in a three-phase flow displacement experiment. PROPOSED METHOD The fundamentals established by Buckley and Leverett5 for two-phase flow were extended to three - phase flow and used as a basis for the derivation of saturation equations. This approach is comparable to Welge's6 use of Buckley and Leverett theory in arriving at expressions to determine the outflow face saturation of the displacing fluid in a two-phase flow system.

Jan 1, 1967

By S. S. Clarke

THEN sufficient ore has been blocked out on a lease to warrant a shaft, the proposed. Location of the shaft should be carefully considered, as the old promoter's method of sinking wherever his hat landed is a sad mistake as some: of us have learned by trying to operate such mines. In some instances certain conditions exist, such as mill location, railroad right of way, etc., that necessitate a change of location from the. ideal, but under average conditions and with the knowledge of the formation gained from the drill logs and with the general trend of the orebody known, the shaft can be located from. the standpoint of its future relation to the mine with re-gard to hauling and' hoisting a maximum tonnage: at a minimum cost per ton, also taking into account the minimum amount of expense and trouble- in sinking. Quite a few shafts are located in the wall of a run or just in the thin edge of the orebody: As a general rule the formation here is solid and permits rapid and safe sinking, and the shaft pillars are left in practically valueless material. This permits the withdrawal of pillars and still keeps the shaft protected. By opening a shaft in thin ground, you are not tempted to cut it high, wide, and handsome, but to shape it up-with ample clearance for lay-bys and with more of an idea of permanency, as a few hundred extra dollars spent around the shafts for proper track installation will re-turn, a good rate of interest in ease of handling "cans," quick get-away; and fewer wrecks. Nearly all the shafts in this district are sunk on a contract basis, the con-tractors furnishing all labor and explosives, and the company building the sinking-derrick, dump-track, and furnishing, all equipment, material, and power. The following costs are the averages, for three shafts sunk through good solid formation, with no water to, contend with, and approximately 260 -ft., deep, having about-100 ft. of shale. The contract price was $9 per foot with the shale and $13 per foot in the solid, making a total of $2,980 paid to the contractor. The wages paid by the contractor were, $5 per shift for the hoist-man, who also sharpened steel, $6 for the lead shaft man, and $5 for the helper;, the cribbing was sawed on contract for 40c. per shaft: foot; about. 94 board feet. of cribbing was used per foot of staggered cribbing and 168 board feet per foot of solid cribbing.

Jan 8, 1928