Search Documents

By A. F. Brock

The cut-and-fill mining methods in use in the mines of The International Nickel Company of Canada Limited, at Falconbridge Nickel Mines Limited, in the Sudbury District, and at McIntyre Porcupine Mines Limited in the Porcupine District, are typical of the general cut-and-fill practice in both the base-metal mines and the gold mines in the Province of Ontario. The following pages describe the methods in use. HORIZONTAL CUT-AND-FILL STOPING Horizontal cut-and-fill stoping, as practiced in the mines of The International Nickel Company of Canada Limited, falls into two main classifications: (I) transverse cut-and-fill stoping, where ground conditions or wide ore bodies make it necessary to establish narrow stopes and pillars across the width of the ore body; (2) longitudinal cut-and-fill stoping where ore body widths and ground conditions allow safe mining of the full width of the ore body. Transverse Cut-and-fill StopiNg General Stoping Layouts Stope and Pillar Widths.—For transverse stoping, experience has indicated that narrow stopes and pillars, 27 ft. 6 in and 22 ft., respectively, are most satisfactory. These width are multiples of 5 ft. 6 in., which is the center to center dimension of a standard square set. Thus any stope, or block of stopes, can be readily converted from cut-and-fill to square set-and-fill if ground conditions should warrant such a change. Formerly, pillars were established 16 ft. 6 in. wide, the equivalent of the width of three square sets, with the intention of extracting the pillars by mining an overhand slice one set wide and an underhand slice two sets wide. However, subsequent experience proved that a two-set overhand slice is so much more efficiently mined than a one-set slice, and 22-ft. pillars have been made standard. Chutes.—The stope chutes are established on the longitudinal center line of the stopes and are spaced at 22-ft. centers from footwall to hanging wall. The footwall chute is usually from 5 to 10 it. from the footwall of the stope. It is offset where necessary at an angle of 52° and vertical chutes are carried from the offset at 22-ft. centers. In sections of the ore body where a flat hanging wall would cut off hanging-wall chutes within a few cuts of the sill, it has proved to be more economical to use temporary chutes or slushers, or both, for these first few cuts, rather than to el permanent chutes at the hanging wall.

Jan 1, 1946

By Oscar T. Marzke

Four alloys that precipitate the alpha phase from the beta of the copper-zinc system were heat-treated in various ways to develop as many forms of the segregate as possible. It was found that the precipitate may have the form either of plates or of needles. Plates usually result when precipitation occurs at low temperatures and needles when precipitation takes place at high temperatures. The needles tend to align themselves along certain planes in the matrix and to coalesce into plnte-like structures. The two phases were found to be related so that a (111) plane and [Oil] direction of the precipitate are parallel to a 10111 plane and 11111 direction of the matrix. DISCUSSION (E. A. Anderson presiding) D. W. Smith, Pittsburgh, Pa. (Written discussion).—Tllis report by Dr. Marzke covers completely all possible heat treatinents over a considerable range of compositiol~s in which a1pha precipitates from beta brass, and may be said to complete the Inctallographic part of this problern The lining up of ncedles of segregate to form plates, espeeially as shown in Fig. 5, appears to he regular, although the author's frequency plot in Fig. 11 makes it appear rather irregular. Has the author attempted anY correlation between some of the major dircetions and the oricntntaion of the parent grain as determined by X-ray analysis? Also, in Figs. 4, 5 and 6 the cross-sections of the needles appear to be straightsided and regular. Have these directions been correlated with the matrix latttice? Dr. Mnrzkr 's method of interpretation of the orientation rclationships between the alpha. and beta phases is a bit uncertain and seems to wed more explanation. If this relationship, as staited is such that :L (1111 plane and a [I 10] direction of that plane in the precipitate is parallel to a. {110} p1ane and a [111] direction of that, plane in the matrix, there mill be a maximum of 24 possible orientations of the alpha phase within a. single grain of the beta phasc. This relationship is expressed strercographical1y in Fig. 13, ill which the locations of a11 of the alpha {111} poles for the 24 orientations of alpha me given. Fig. 12 chccks fairly closely with this thcoretical plot,. with a few exeeptions which may be due to the inaceuracy inherent in the method used by the anthor in determining the orientations of the segregates. The method might have been refined somewhat had corrections been made for the displacement of the slip p1ancs upon deformation.

Jan 1, 1933

By J. Szekely, P. Tarassoff, N. J. Themelis

In a copper converter air enters the bath in the form of turbulent jets. The interaction of these jets with the molten matte is fundamental to the converting process. In the present study, an equation is derived to describe the trajectory of a gas jet in a liquid. Calculated and experimental results for air jets injected into water are in good agreement. The trajectories of air jets in copper matte are predicted. THE air injected through the tuyeres of a Peirce-Smith copper converter emerges into the bath of molten matte in the form of a highly turbulent jet. The air jets affect a number of chemical and physical processes occurring in the converter: i) Converting Rate. It is generally recognized that the production capacity of a converter is limited by the flow of air which can be injected through the tuyeres and by the oxygen efficiency. In turn, the air flow is limited by pressure drop considerations or by the amount of splashing within the converter. ii) Oxygen Efficiency. This depends on the dispersion of the air jet in the liquid bath, and its trajectory through the bath. iii) Mixing. The jets act as mixing devices by transferring momentum energy to the bath; in this way the heat generated by the converting reactions occurring in the jets is distributed through the bath. iv) Refractory Wear. The proximity of the jets, which are centers of heat generation, to the refractories in the tuyere zone may have an important effect on refractory life. Mixing conditions in the bath will also influence refractory erosion. v) Splashing, and Accretion Build-Up. The energy of the jets is not dissipated entirely in mixing the bath. particles of liquid are carried out kith the gas above the surface of the bath in the form of liquid spouts and droplets. These result in the undesirable build-up of accretions on the converter mouth, and dust losses in the flue gas. Despite the importance of the interaction of the air jets and the matte in a converter, very few studies of the fluid dynamics of converting have been reported in the literature. Metallurgists in the USSR appear to have been more concerned with the subject than their Western counterparts. Deev et al.1 studied the interaction of an air jet with aqueous solutions in a converter model and qualitatively determined the tuyere air velocity and tuyere inclination which produced the most favorable results with respect to good mixing in the bath, and minimum splashing. Shalygin and Meyer-ovich2 also examined the air-matte physical interaction both in models and in industrial converters; they concluded that in conventional converting practice, there was no significant penetration of the air jets into the matte layer, and consequently the converting reactions occurred mainly in a zone adjacent to the tuyeres. The behavior of air jets in a converter bath, and the aerodynamic characteristics of tuyeres are discussed at length in a monograph on converting by Shalygin.3 However, the description of the phenomena occurring in the converter bath is largely qualitative. The side-blown Bessemer converter for steelmak-ing is very similar to the Peirce-Smith copper converter. Among the few investigations of the behavior of air jets in the bath of a Bessemer converter are those of Kootz and Gille4 who studied splashing in the course of an investigation on the effect of blowing conditions and converter shape on nitrogen pick-up in Bessemer steel. They found that during blowing standing waves were formed on the surface of the bath; the amplitude of the waves increased with the depth and angle of tuyere immersion until the whole bath moved backwards and forwards causing heavy splashing. Kazanstev5 used a model of a Bessemer converter to obtain correlations between the axial velocity of a gas jet and distance from the tuyere orifice and the Froude number of the jet. shalygin3 used these results to calculate the horizontal penetration of an air jet in a copper converter; the penetration was defined as the distance in which the axial jet velocity decreased to 10 pct of its initial value. However, the rising trajectory of the jet was not taken into account. In the absence of quantitative information on the fluid dynamics of converting, the design of copper converters has been based mainly on operating experience. Such experience tends to vary widely from smelter to smelter., This is reflected in Table I which is based on data compiled by Lathe and Hodnett.6 Aside from a rough, and perhaps obvious correlation between the total air flow and converter volume, Fig. 1, no pattern emerges from the data. For example, tuyere throat air velocities vary from 215 to 465 ft per sec in converters of the same size, for little apparent reason. The air jet energy input per cubic foot of converter volume, which may be taken as a measure of the amount of mixing in the converter bath, also varies greatly. A recent analysis of converter data by Milliken and Hofinger7 has also revealed unexplained variations in operating parameters. It is believed that by gaining a better understanding of the fluid dynamics of converting a more rational basis may be provided for the design of converters. In particular, it is proposed that if one takes into account the desirable criteria of a high converting rate, high oxygen efficiency and long refractory life, there should be an optimum configuration of tuyere air flow for a converter of a given diameter. The present investigation is concerned with the form and trajectory of an air jet in a converter bath. The general theory of turbulent jets has been expounded by Schlichting8 and Abramovich.9 However, most experi-

Jan 1, 1970

By C. A. Hartnagel

In 1939 the production of crude oil in New York totaled 5,105,000 bbl. This marks the third consecutive year production of crude oil has exceeded 5,000,000 bbl. and only once has this total been surpassed—in the year 1882, three years after the discovery of oil in Allegany County, when the annual production was more than 6,000,000 barrels. The most gratifying feature of the industry was the increased demand for lubricants, which resulted in advanced prices for crude. From a price at the beginning of the year of $1.68 per barrel, six advances totaling 82c brought the year's closing to $2.50 per barrel. A further increase in price on Jan. 1, 1940, to $2.75 per barrel places the local industry in a strong position for the year's operations. Most of the oil production of the state is now obtained by water-flooding, and the industry is practically stabilized. No new pools have been discovered in over 25 years, and border drilling indicates little prospect of extending the boundaries of the fields beyond their present limits. Deep drilling to the Oriskany sandstone in and close to the present oil fields hay failed to find oil in substantial amounts. Altogether, the oil pools of New York have produced during the 60 years that they have been exploited approximately 125,000,000 bbl. of oil. Following the flush production of 1882, the annual production gradually dccrcased and the year 1912 marked an all-time low of only 782,000 bbl. In 1919, as a result of flooding operations, a definite upward trend in oil production was recorded. During that year also the production of oil by water-flooding methods as approved by Legislative action. In the 21-yr. period beginning with 1919, oil production in the state ha.: totaled 60,338,000 bbl. Thus it will be seen that by the aid of flooding methods nearly as much oil has been produced in the last 21 yr. as in the preceding 40 yr., although the Iatter period included the flush production in 1882. As there is little hope of extending the area of the present producing oil fields of the state, producers and refiners are concerned regarding the future life of the fields. It is encouraging to observe that earlier esti- Published by permission of Director of New York State Museum, Albany, N. P. Summarized at meeting; manuscript received at the office of the Institute March 20. 1940.

Jan 1, 1940

By C. A. Hartnagel

In 1939 the production of crude oil in New York totaled 5,105,000 bbl. This marks the third consecutive year production of crude oil has exceeded 5,000,000 bbl. and only once has this total been surpassed—in the year 1882, three years after the discovery of oil in Allegany County, when the annual production was more than 6,000,000 barrels. The most gratifying feature of the industry was the increased demand for lubricants, which resulted in advanced prices for crude. From a price at the beginning of the year of $1.68 per barrel, six advances totaling 82c brought the year's closing to $2.50 per barrel. A further increase in price on Jan. 1, 1940, to $2.75 per barrel places the local industry in a strong position for the year's operations. Most of the oil production of the state is now obtained by water-flooding, and the industry is practically stabilized. No new pools have been discovered in over 25 years, and border drilling indicates little prospect of extending the boundaries of the fields beyond their present limits. Deep drilling to the Oriskany sandstone in and close to the present oil fields hay failed to find oil in substantial amounts. Altogether, the oil pools of New York have produced during the 60 years that they have been exploited approximately 125,000,000 bbl. of oil. Following the flush production of 1882, the annual production gradually dccrcased and the year 1912 marked an all-time low of only 782,000 bbl. In 1919, as a result of flooding operations, a definite upward trend in oil production was recorded. During that year also the production of oil by water-flooding methods as approved by Legislative action. In the 21-yr. period beginning with 1919, oil production in the state ha.: totaled 60,338,000 bbl. Thus it will be seen that by the aid of flooding methods nearly as much oil has been produced in the last 21 yr. as in the preceding 40 yr., although the Iatter period included the flush production in 1882. As there is little hope of extending the area of the present producing oil fields of the state, producers and refiners are concerned regarding the future life of the fields. It is encouraging to observe that earlier esti- Published by permission of Director of New York State Museum, Albany, N. P. Summarized at meeting; manuscript received at the office of the Institute March 20. 1940.

Jan 1, 1940

By Howard I. Smith

THE mineral trona was discovered on Government land in 1938, about 18 miles west of the town of Green River, Wyo., in the core of the John Hay, Jr., well, a test well drilled for oil by the Mountain Fuel Supply Co. in sec. 2, T. 18 N., R. 110 W., sixth principal meridian. Although no oil or gas was reported, the drilling led to a discovery of great potential economic importance and exceptional scientific interest. Trona is a relatively rare mineral found at various places in playa deposits but not previously found at any great depth. It is composed of hydrous sodium carbonate and sodium bicarbonate (Na2CO3.NaHCO3.2H20). Pure trona contains the equivalent of 70.35 per cent of sodium carbonate. Total sodium computed to carbonate times 1.42 equals the percentage of trona in the absence of other sodium carbonate minerals in the sample. ANALYSES Two short pieces of core sent to the author a few days after the completion of the Hay well were analyzed by R. C. Wells[t] and found to be exceptionally pure trona. A brief article on this discovery has already been published.1 Arrangements were then made through W. T. Nightengale[$] for the author to inspect and sample the core. The company log of the well included notations of sodium salt crystals from a depth of 1190 to 1820 ft. Not being able to identify all the minerals present, the author selected several specimens of the core for petrographic examinations and sampled the sections of trona for analysis. J. J. Fahey, of the Geological Survey, examined the specimens and reported most of the crystals to be a new anhydrous sodium carbonate and calcium carbonate mineral (Na2CO3.2CaCO3), which he named shortite,2 after Maxwell N. Short.* He analyzed the samples of trona, with the results shown in Table I. [ ] In addition to the 10 ft. I in. of trona in the first section, it is reasonable to assume that the 9 ft. 8 in. for which no core was available for sampling is either mostly trona or some other soluble salt, but it should not be included in calculating reserves. In the part of the core between 1590 ft. 3 in. and I600 ft. 4 in. the material insoluble in cold water, amounting to about 5 per cent, was estimated petrographically to contain 70 per cent clay, 25 per cent shortite, and 5 per cent pyrite. ACCOMPANYING MINERALS Fahey later secured about 600 ft. of the core for a detailed examination and study

Jan 1, 1942

Discussion of the paper of Dorsey A. Lyon and Robert M. Keeney, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 2117 to 2149. C. D. WOODWARD, Butte, Mont.:-We constructed a small blast furnace, and used first carbon electrodes and an alternating current of about 50 to 75 volts. We were able to smelt the material which was fed to the furnace, but we did not carry on experiments far enough to see just exactly what the power consumption was and compare it with the amount of material treated. We found that the blast seemed to help materially in reducing our charge and cutting down our power consumption. There were several other experiments tried at the time, and I do not call to mind now just what they were. We were trying to do away with the carbon electrode and replace it with an iron one, and it also seems to me we tried to use the ore for an electrode; but I believe that the electric furnace in the reducing end is simply a question of British thermal units per kilowatt-hour compared with British thermal units in a pound of coke. Now, if a pound of coke costs us 0.5 c. and a kilowatt-hour costs us in the neighborhood of 1.5 c., I think there is a big advantage in using coke instead of the electrical current for copper reducing. We tried steam, and a number of other methods, to throw copper down, but it has been some time ago and I am not very familiar with them now. The outlook of the experiments did not seem to be very promising, and we took it more as a thermal problem than an electrical one. PROF. JOSEPH W. RICHARDS, South Bethlehem, Pa.:-Mr. Woodward has spoken of the question as a thermal problem. I would call attention to the fact that electric furnaces usually utilize the heat of the electric current at from four to ten times the efficiency with which the heat generated by fuel is utilized; so it will not do simply to compare by thermal units generated. Your total thermal units may cost much less from coke than from electricity, yet you will find the electrically generated thermal units utilized in a properly designed furnace from three to ten times more efficiently than in the combustion furnace. You must make that allowance is comparing the cost of thermal units generated electrically and thermal units from coke.

Jan 11, 1913

By Richard J. Borg

The vapor pressure of Cd in equilibrium with CdSb in the presence of excess Sb has been measured using the Knudsen effusion method over the temperature range 276° to 379°C. The free energy of formation of CdSb is given by AF° = -1.58 + 1.53 x l0-4 T, kcal per mole. The enthalpy and entropy are obtained from the temperature coefficient of the .free energy. CADMIUM and antimony have almost imperceptible mutual solid solubility but form a single stable intermediate phase, CdSb. This phase, according to Han-sen,l extends from about 49.5 at. pct to 50 at. pct Cd at 300°C and has the orthorhombic structure. The free energy of formation of CdSb can be calculated from the vapor pressure of Cd for compositions which contain less than 49 at. pct Cd. The appropriate reaction and formulae are given by Eqs. [I] and [2]- CdSb(s, ~ Cd(g)-, +Sb(s) [1] Since Sb is in its standard state, Af - N,,AF'-,, = NcdRT In a,, = NcdRT InP/PO [2] In Eq. [2], P, is the vapor pressure of Cd in equilibrium with the alloy, and Po is the vapor pressure in equilibrium with pure solid Cd. It is implicit in this calculation that the free energy only slightly changes within the narrow limits of the single phase field. Thus, the value obtained from the antimony-rich boundary is truly representative of the stoi-chiometric compound. The results reported herein are obtained from a mixture near the eutectic composition, i.e. 59 at. pct Sb. Only two previous investigations" of the free energy of formation of CdSb have been made. Both relied upon the electromotive force method, and measurements were made over relatively narrow temperature ranges which strongly influences the reliability of the values of AH and aS. EXPERIMENTAL The eutectic composition is prepared by fusing reagent grade Cd and Sb by induction heating in vacuo with the starting materials held in a graphite crucible having a threaded lid. The material obtained from the initial melt is pulverized, sealed under high vacuum in a pyrex capsule, and annealed at 420°C for two weeks. X-ray analysis"gives the following lattize parameters: a = 6.436A, b = 8.230& and c = 8.498A using Cu Ka radiation with A = 1.54056. These values are in fair agreement with the result? previously reported by Al~in:4 i.e. a = 6.471A, b = 8.253A, and c = 8.526A. Vapor pressures are measured using an apparatus which has been described elsewhere,= however, with a single important modification. Knudsen effusion cells are made of pyrex with knife-edged orifices made by grinding the convex surface of the lid on #600 emery paper. Photographs taken at known magnifications using a Leitz metallograph enable the determination of the orifice area. Numerous calibration measurements of the vapor pressure of pure Cd give close agreement with values previously reported5,= thus indicating that no significant error can be ascribed to the substitution of glass cells for metal cells used in previous work. Because the vapor pressure of Cd is reliably established and because it is difficult to obtain Clausing factors for the glass cells, the final values used for the orifice areas are calculated from the calibration measurements of the vapor pressure of pure Cd. Effusion runs are started in an atmosphere of purified helium which is quickly evacuated as soon as the cell attains thermal equilibrium. Less than one minute is necessary to obtain high vacuum after evacuation begins, and the temperature seldom varies by more than 0.5oC from the value obtained prior to pumping out the helium. RESULTS The results of this investigation along with other pertinent data are tabulated in Table I. Fig. 2 is the familiar graph of log P against T-10 K. At least mean squares analysis of the data presented in Table I yields the following equation: log1DJP = 8.790 - 6472 x T"1 [3] The deviations of the individual measurements from the values calculated with Eq. 131 are given in column six of Table I; the average deviation is 4.0% of the calculated value. Although the partial molal properties change significantly with composition within the single phase region, the integral thermodynamic value should remain relatively constant. Hence the results of the following calculations, which use the data obtained for the eutectic composition, are probably representative of the equi-atomic compound. Eq. [4] describes the vapor pressure of pure Cd as a function of temperature and may be combined with Eq. [3] to

Jan 1, 1962

The cut-and-fill mining methods in use in the mines of The International Nickel Company of Canada Limited, at Falconbridge Nickel Mines Limited, in the Sudbury District, and at McIntyre Porcupine Mines Limited in the Porcupine District, are typical of the general cut-and-fill practice in both the base-metal mines and the gold mines in the Province of Ontario. The following pages describe the methods in use. HORIZONTAL CUT-AND-FILL STOPING Horizontal cut-and-fill stoping, as practiced in the mines of The International Nickel Company of Canada Limited, falls into two main classifications: (I) transverse cut-and-fill stoping, where ground conditions or wide ore bodies make it necessary to establish narrow stopes and pillars across the width of the ore body; (2) longitudinal cut-and-fill stoping where ore body widths and ground conditions allow safe mining of the full width of the ore body. Transverse Cut-and-fill StopiNg General Stoping Layouts Stope and Pillar Widhs.—For transverse stoping, experience has indicated that narrow stopes and pillars, 27 ft. 6 in and 22 ft., respectively, are most satisfactory. These width are multiples of 5 ft. 6 in., which is the center to center dimension of a standard square set. Thus any stope, or block of stopes, can be readily converted from cut-and-fill to square set-and-fill if ground conditions should warrant such a change. Formerly, pillars were established 16 ft. 6 in. wide, the equivalent of the width of three square sets, with the intention of extracting the pillars by mining an overhand slice one set wide and an underhand slice two sets wide. However, subsequent experience proved that a two-set overhand slice is so much more efficiently mined than a one-set slice, and 22-ft. pillars have been made standard. Chutes.—The stope chutes are established on the longitudinal center line of the stopes and are spaced at 22-ft. centers from footwall to hanging wall. The footwall chute is usually from 5 to 10 ft. from the footwall of the stope. It is offset where necessary at an angle of 52° and vertical chutes are carried from the offset at 22-ft. centers. In sections of the ore body where a flat hanging wall would cut off hanging-wall chutes within a few cuts of the sill, it has proved to be more economical to use temporary chutes or slushers, or both, for these first few cuts, rather than to el permanent chutes at the hanging wall.

Jan 1, 1946

By Howard I. Smith

The mineral trona was discovered on Government land in 1938, about 18 miles west of the town of Green River, Wyo., in the core of the John Hay, Jr., well, a test well drilled for oil by the Mountain Fuel Supply Co. in sec. 2, T. 18 N., R. IIO W., sixth principal meridian. Although no oil or gas was reported, the drilling led to a discovery of great potential economic importance and exceptional scientific interest. Trona is a relatively rare mineral found at various places in playa deposits but not previously found at any great depth. It is composed of hydrous sodium carbonate and sodium bicarbonate (Na2CO3 NaHCo3.2H2O). Pure trona con-tains the equivalent of 70.35 per cent of sodium carbonate. Total sodium computed to carbonate times 1.42 equals the percentage of trona in the absence of other sodium carbonate minerals in the sample. Analyses Two short pieces of core sent to the author a few days after the completion of the Hay well were analyzed by R. C. Wells† and found to be exceptionally Pure trona. A brief article on this discovery has already been published.1 Arrangements were then made through W. T. Nighten-gale‡ for the author to inspect and sample the core. The company log of the well included notations of sodium salt crystals from a depth of 1190 to 1820 ft. Not being able to identify all the minerals present, the author selected several specimens of the core for petrographic examinations and sampled the sections of trona for analysis. J. J. Fahey, of the Geological Survey, examined the specimens and reported most of the crystals to be a new anhydrous sodium carbonate and calcium carbonate mineral (Na2CO 3.2 CaCO3), which he named shortite,² after Maxwell N. Short." He analyzed the samples of trona, with the results shown in Table I. In addition to the 10 ft. 1 in. of trona in the first section, it is reasonable to assume that the 9 ft. 8 in. for which no core was available for sampling is either i mostly trona or some other soluble salt, but it should not be included in calculating | reserves. In the part of the core between i 1590 ft. 3 in. and 1600 ft. 4 in. the material insoluble in cold water, amounting to about 5 per cent, was estimated petrographically I to contain 70 per cent clay, 25 per cent shortite, and 5 per cent pyrite. Accompanying Minerals Fahey later secured about 600 ft, of the core for a detailed examination and study

Jan 1, 1942

By Howard I. Smith

The mineral trona was discovered on Government land in 1938, about 18 miles west of the town of Green River, Wyo., in the core of the John Hay, Jr., well, a test well drilled for oil by the Mountain Fuel Supply Co. in sec. 2, T. 18 N., R. IIO W., sixth principal meridian. Although no oil or gas was reported, the drilling led to a discovery of great potential economic importance and exceptional scientific interest. Trona is a relatively rare mineral found at various places in playa deposits but not previously found at any great depth. It is composed of hydrous sodium carbonate and sodium bicarbonate (Na2CO3 NaHCo3.2H2O). Pure trona con-tains the equivalent of 70.35 per cent of sodium carbonate. Total sodium computed to carbonate times 1.42 equals the percentage of trona in the absence of other sodium carbonate minerals in the sample. Analyses Two short pieces of core sent to the author a few days after the completion of the Hay well were analyzed by R. C. Wells† and found to be exceptionally Pure trona. A brief article on this discovery has already been published.1 Arrangements were then made through W. T. Nighten-gale‡ for the author to inspect and sample the core. The company log of the well included notations of sodium salt crystals from a depth of 1190 to 1820 ft. Not being able to identify all the minerals present, the author selected several specimens of the core for petrographic examinations and sampled the sections of trona for analysis. J. J. Fahey, of the Geological Survey, examined the specimens and reported most of the crystals to be a new anhydrous sodium carbonate and calcium carbonate mineral (Na2CO 3.2 CaCO3), which he named shortite,² after Maxwell N. Short." He analyzed the samples of trona, with the results shown in Table I. In addition to the 10 ft. 1 in. of trona in the first section, it is reasonable to assume that the 9 ft. 8 in. for which no core was available for sampling is either i mostly trona or some other soluble salt, but it should not be included in calculating | reserves. In the part of the core between i 1590 ft. 3 in. and 1600 ft. 4 in. the material insoluble in cold water, amounting to about 5 per cent, was estimated petrographically I to contain 70 per cent clay, 25 per cent shortite, and 5 per cent pyrite. Accompanying Minerals Fahey later secured about 600 ft, of the core for a detailed examination and study

Jan 1, 1942

By Howard I. Smith

THE mineral trona was discovered on Government land in 1938, about 18 miles west of the town of Green River, Wyo., in the core of the John Hay, Jr., well, a test well drilled for oil by the Mountain Fuel Supply Co. in sec. 2, T. 18 N., R. 11o W., sixth principal meridian. Although no oil or gas was reported, the drilling led to a discovery of great potential economic importance and exceptional scientific interest. Trona is a relatively rare mineral found at various places in playa deposits but not previously found at any great depth. It is composed of hydrous sodium carbonate and sodium bicarbonate (Na2CO3.NaHCO3.2H2O). Pure trona contains the equivalent of 70.35 per cent of sodium carbonate. Total sodium computed to carbonate times 1.42 equals the percentage of trona in the absence of other sodium carbonate minerals in the sample. ANALYSES Two short pieces of core sent to the author a few days after the completion of the Hay well were analyzed by R. C. Wells† and found to be exceptionally pure trona. A brief article on this discovery has already been published.1 Arrangements were then made through W. T. Nightengale‡ for the author to inspect and sample the core. The company log of the well included notations of sodium salt crystals from a depth of 1190 to 1820 ft. Not being able to identify all the minerals present, the author selected several specimens of the core for petrographic examinations and sampled the sections of trona for analysis. J. J. Fahey, of the Geological Survey, examined the specimens and reported most of the crystals to be a new anhydrous sodium carbonate and calcium carbonate mineral (Na2CO3.2CaCO3), which he named shortite,2 after Maxwell N. Short.* He analyzed the samples of trona, with the results shown in Table i. [ ] In addition to the 10 ft. I in. of trona in the first section, it is reasonable to assume that the 9 ft. 8 in. for which no core was available for sampling is either mostly trona or some other soluble salt, but it should not be included in calculating reserves. In the part of the core between 1590 ft. 3 in. and 1600 ft. 4 in. the material insoluble in cold water, amounting to about 5 per cent, was estimated petrographically to contain 70 per cent clay, 25 per cent shortite, and 5 per cent pyrite. ACCOMPANYING MINERALS Fahey later secured about 600 ft. of the core for a detailed examination and study

Jan 1, 1942

By A. M. Gaudin, F. W. Bowdish

MINERAL dressing is an industrial art concerned with the treatment and separation of solids suspended in fluids. Knowledge and evaluation of the area of solid-fluid interface is important in all cases except those involving only large pieces of solid. In fact, many problems relating to comminution, to flotation, to thickening and classification, could be dealt with more rationally if the interfacial area were known. A number of methods have been proposed for the measurement of the surface of certain finely divided solids. Among them are methods using rate of dissolution of the solid,7 its magnetic remanence,3 the turbidity of its suspension,8 and the character of the size distribution of the material.9 The first two are limited to one mineralogical species per sample; the third has certain optical limitations, especially for mineral mixtures, and the fourth is based on an extrapolation of uncertain validity. The need of a better and more general method of surface determination has long been felt, therefore. The method of P. H. Emmett,4 based upon the low-temperature adsorption of vapors, appears to fulfill this need. This method consists in determining the amount of nitrogen that is adsorbed by a given sample of solid at the temperature of boiling nitrogen. The more surface there is on the solid-both internal and external-the more nitrogen is abstracted. In actual operation, the method is somewhat less simple than has been stated so far, in that the nitrogen is adsorbed in an incomplete layer, the completeness and thickness of the layer being related to the pressure of the nitrogen in contact with the sample .2 This circumstance makes it necessary to determine the nitrogen adsorption for three or more values of the nitrogen pressure. APPARATUS In the Richards Mineral Dressing Laboratories an Emmett apparatus has been built and tested (Figs. 1 and 2). A mechanical vacuum pump B and a mercury diffusion pump A work in series to give a high vacuum. The sample, placed in bulb D, can be evacuated by this pump train by suitable operation of the stopcocks in the glass tubing that connects the various parts of the apparatus. C is a McLeod gauge, used to ascertain the order of magnitude of the vacuum obtained, and not for accurate pressure measurements. Pressure measurements are made in the mercury manometer F and gas-volume measurements in the gas burette E. Gases are stored in flasks L (nitrogen) and K (helium), arranged so that definite quantities of these gases can be introduced into

Jan 1, 1944

By David Moskowitz, Ira Binder, Robert Steinitz

THE hard refractory borides of the transition elements of the 4th, 5th, and 6th groups of the Periodic System have been the subject of a number of recent investigations.'-' It is well known now that most of these elements form several different borides, and Kiessling8 has summarized the rules which govern to some extent the arrangements of the boron atoms in the various structures. Melting points of a few borides have been published." The systems Fe-B, Ni-B, and Co-B have been reported," but, as these borides are rather low melting, they are outside of the groups of boron compounds considered here. Brewer' has tested the stability of various borides and estimated a number of eutectic temperatures between different borides, but in no case was the complete system of a transition metal and boron investigated. The phase diagram becomes of special importance if the preparation of the borides from the elements in powdered form is considered; the lowest eutectic temperature will determine the first appearance of a liquid phase. Also, the knowledge of high temperature phases, if they exist, is important for the preparation of bodies from these borides by hot pressing or sintering. During the investigation of various metal borides,7 it was found that there were more boride phases existing in the Mo-B system than reported by Kiessling." They occur, however, only at temperatures above 1500°C and were, therefore, not found by him. This led to a study of the equilibrium diagram of the Mo-B system. ranging from 0 to 25 pct B and from room temperature to the liquidus. Part of this investigation was reported during the "Research in Progress" session at the 1952 Annual Meeting of the AIME.11 Raw Materials and Preparation of the Borides The raw materials used were commercial molybdenum and boron powder, both supplied by the Molybdenum Corp. of America. The molybdenum powder was 99+ pct pure? while the boron powder contained about 83 to 85 pct B. A large percentage of the impurities in this powder was oxygen, with the rest formed by iron, calcium, and unknown substances. The low purity of the boron used was, however, not considered detrimental to the final product, as most of the impurities evaporated at the high temperatures at which the borides were formed. The final product always had a minimum purity of 96 to 98 pct (figured as molybdenum and boron), with carbon, iron, and probably oxygen being the remaining products. Carbon is usually present as graphite. The chemical analyses always confirmed the compositions which corresponded to the crystallographic structures as determined by X-ray diffraction, and the boron content of the finished product agreed closely with that of the starting mixture; no boron was lost during the boride preparation. The chemical analysis methods employed for molybdenum and boron were previously described by Blumenthal.12,13 The powders were mixed by hand in the desired proportions, compressed at room temperature under low pressure, and then heated under hydrogen to about 1500" to 1700°C in a graphite crucible to form the borides. Usually, the three well-known borides Mo,B, MOB, and Mo,B,, which are stable at room temperatures, were prepared in this way, and all other compositions were made by mixing these borides in various ratios or by the addition of molybdenum or boron powders for the very low or very high boron contents. Preparation of two-phase compositions directly from the elemental powders was tried only occasionally to check whether equilibrium could be reached in this way. Experimental Procedures The stable borides were mixed in the desired ratios and heated under hydrogen in graphite crucibles to various temperatures. The well insulated crucibles were heated in a high frequency induction furnace. Special care was taken to obtain exact temperature measurement, which proved much more difficult than originally anticipated. It is believed that individual temperature measurements have an error of less than ±25ºC, while melting or transformation temperatures are accurate within ±50°C. The temperatures were measured with an optical pyrometer which was aimed at the closed end of a graphite tube extending down into the crucible. close to the samples. Attempts to measure directly through the hydrogen exit stack failed. The crucible arrangement is shown in Fig. 1. Heating was done at a slow rate to be sure that the temperature inside the crucible was uniform. The specimens were kept at the final temperature for about 30 min. For the investigation of high temperature phases, some samples were quenched. They were heated, without atmosphere protection, in a very small graphite crucible which could be rapidly removed from the high frequency coil, and dropped into water. These quenched samples were afterwards annealed to establish the equilibrium at lower temperatures. The melting points or the positions of the solidus and liquidus lines were determined by heating the specimens to various temperatures and examining them at room temperature for evidence of a liquid phase. These results were checked later on by thermal arrest curves, especially to determine the exact position of the eutectic temperature line. For this purpose about 200 g of the boride were melted in a graphite crucible, in an arrangement similar to Fig. 1. Slow cooling was assured by very good

Jan 1, 1953

By J. R. Szedon, T. L. Chu, G. A. Gruber

Amorphous adherent filnzs of silicon dioxide have been deposited on silicon substrates by the oxidation of silane at temperatures ranging from 650 to 1050C. Various diluents (argon, nitrogen, hydrogen) were used to suppress the formation of SiO2 in the gas phase. Deposition rates of the oxide were determined over the temperature range in question as functions of' re-actant flow rates. Etch rate studies were used for a cursory comparison of structural properties of deposited and thermally grown oxides. From electrical evaluation of metal-insulator-silicon capacitors it was determined that the interface charge density of deposited films is similar go that of dry-oxygen-grown films in the 850° to 1050 C temperature range. Deposited films exhibit several ionic instability effects which differ in detail from those reported for thermal oxides. Stable passivating films of silicon nitride over deposited oxides appear to be practical for use in silicon planar device fabrication. Such films can be prepared under temperature conditions which have less effect on substrate impurity distributions than in the case of grown oxides. AMORPHOUS silicon dioxide (silica) is compatible with silicon in electrical properties and is the most widely used dielectric in silicon devices at present. Silica films can be prepared by the oxidation of silicon or deposited on silicon or other substrate surfaces by chemical reactions or vacuum techniques. The ability of thermally grown silicon dioxide films to passivate silicon surfaces forms one of the practical bases of the planar device technology. Properly produced and treated films of grown SiO 2 can have low densities of interface charge (-1 X 10" charges per sq cm) and can be stable as regards fast migrating ionic sgecies. 1 To maintain these properties, even with an otherwise hermetically sealed ambient, the Sia layers must be at least l000 A thick. Such thicknesses require oxidation in dry oxygen for periods of 7.8 hr at 900°C or 2 hr at 1000°C. Although oxidation in steam or wet oxygen can reduce these times to 17 and 5 min, the resulting oxides must be annealed to produce acceptable levels of interface charge., Oxidation or annealing involving moderate to high temperatures for extended periods of time can be undesirable. Under some conditions, there can be changes in the distribution of impurities within the underlying substrate. A chemical deposition technique using gaseous am-bients is particularly attractive and flexible for preparing oxide films. With a wide range of deposition rates available, films can be produced under condi- tions of time and temperature less detrimental to impurity distributions in the silicon than in the case of thermal oxidation. The pyrolysis of alkoxysilanes, the hydrolysis of silicon halides, and various modifications of these reactions are most commonly used for the deposition of silica films.3 Silica films obtained in this manner are likely to be contaminated by the by-products of the reaction, organic impurities, or hydrogen halides. The use of the oxidation of silane for the deposition process has been reported recently.4 The deposition of silica films on single-crystal silicon substrates by the oxidation of silane in a gas flow system has been studied in this work. The deposition variables studied were the crystallographic orientation of the substrate surface, the substrate temperature, and the nature of the diluent gas. The electrical charge behavior of Si-SiO2-A1 structures prepared under various conditions was investigated by capacitance-voltage (C-V) measurements of metal-insulator-semiconductor (MIS) capacitors. The experimental approaches and results are discussed in this paper. 1) DEPOSITION OF SILICA FILMS The overall reaction for the oxidation of silane is: The equilibrium constants of this reaction in the temperature range 500° to 1500°K, calculated from the JANAF thermochemical data,= are shown in Fig. 1. In addition to the large equilibrium constants, the oxidation of silane is also kinetically feasible at room temperature and above. However, the strong reactivity of silane toward oxygen tends to promote the nucleation of silica in the gas phase through homogeneous reactions, and the deposition of this silica on the substrate would yield nonadherent material. The formation of silica in the gas phase can be reduced by using low partial pressures of the reactants. Argon, hydrogen, and nitrogen were used as diluents in this work. 1.1) Experimental. The deposition of silica films by the oxidation of silane was carried out in a gas flow system using an apparatus shown schematically in Fig. 2. Appropriate flow meters and valves were used to control the flow of various reactants, i.e., argon, hydrogen, nitrogen, oxygen, and silane. Semiconductor-grade silane, argon of 99.999 pct minimum purity, oxygen of 99.95 pct minimum purity, and nitrogen of 99.997 pct minimum purity, all purchased from the Matheson Co., were used without further purification. In several instances, a silicon nitride film was deposited over the silica film. This was achieved by the nitridation of silane with ammonia using anhydrous ammonia of better than 99.99 pct purity supplied by the Matheson CO.' The reactant mixture of the desired composition was passed through a Millipore filter into a horizontal water-cooled fused silica tube of 55 mm

Jan 1, 1969

By Jack White, Ralph B. Adair

THE Mufulira mine in Northern Rhodesia is 13° south of the Equator and at an altitude of 4100 ft above sea level. The concentrator was planned in 1930 to treat about 10,000 tons of ore per day, but before construction work had gone very far the size of the plant was reduced to 1500 tons daily capacity. Then just as the construction was finished in December 1931, the price of copper did not warrant the commencement of operations and it was not until October 1933 that the mine re-opened. Extensions have been made to the plant in 1034, 1935, 1936 1937, 1940 and finally in 1945. The capacity of the plant when the 1945 extension is completed will be 9500 short tons per day. The various extensions have been carried out with the minimum confusion and with great skill on the part of the designers and the erection engineers. In dealing with the plant in this paper it is proposed to give an outline of the present practice and only to refer to past practice when it is considered of particular interest. ORE TREATED The ore consists of fine grained highly siliceous, felspathic and argillaceous quartzites, the latter containing graphitic carbon and locally termed graywacke. These rocks are considerably altered near the surface and on the fringes of the ore body. Despite extensive efforts at mixing, both underground and in the crushing plant, many sudden changes of ore take place in the mill feed. The minerals are chalcocite, bornite and chalcopyrite with relatively unimportant amounts of malachite, native copper, azurite, covellite and chrysocolla. Gold is present at about 1 oz to a thousand tons, and silver at about 2 dwt. per ton. With increasing depth the nonsulphide content or, as commonly termed locally, the oxide content of the ore is decreasing and is now less than 0.25 pct against a high of 0.77 pct. CRUSHING OPERATIONS The first stage of crushing is done underground where the oversize from 12-in. grizzleys is fed to a 56 X 72-in. jaw crusher. At the Selkirk shaft two 10-ton skips deliver the run of mine ore at a rate of 450 tons per hour to the 400-ton capacity shaft bins. One 6 ft wide Ross chain feeder and one locally made air-operated finger feeder feed the two 30-in. McCully crushers. Ahead of each crusher is a 6 X 9-ft spring grizzley spaced at 5 in. on a 35° slope. Neither the Ross chain feeder nor the finger feeder is entirely satisfactory and for the wet, muddy and sticky ore that has to be handled it is planned to replace these with two 6-ft wide apron pan feeders. The McCully crushers deliver a minus 5-in. product, at a rate of over 500 tons per

Jan 1, 1947

By Jack White, Ralph B. Adair

The Mufulira mine in Northern Rhodesia is 13° south of the Equator and at an altitude of 4100 ft above sea level. The concentrator was planned in 1930 to treat about 10,000 tons of ore per day, but before construction work had gone very far the size of the plant was reduced to 1500 tons daily capacity. Then just as the construction was finished in December 1931, the price of copper did not warrant the commencement of operations and it was not until October 1933 that the mine re-opened. Extensions have been made to the plant in 1934, 1935, 1936, 1937, 1940 and finally in 1945. The capacity of the plant when the 1945 extension is completed will be 9500 short tons per day. The various extensions have been carried out with the minimum confusion and with great skill on the part of the designers and the erection engineers. In dealing with the plant in this paper it is proposed to give an outline of the present practice and only to refer to past practice when it is considered of particular interest. Ore Treated The ore consists of fine grained highly siliceous, felspathic and argillaceous quartz- ites, the latter containing graphitic carbon and locally termed graywacke. These rocks are considerably altered near the surface and on the fringes of the ore body. Despite extensive efforts at mixing, both underground and in the crushing plant, many sudden changes of ore take place in the mill feed. The minerals are chalcocite, bornite and chalcopyrite with relatively unimportant amounts of malachite, native copper, azurite, covellite and chrysocolla. Gold is present at about I oz to a thousand tons, and silver at about 2 dwt. per ton. With increasing depth the nonsulphide content or,, as commonly termed locally, the oxide content of the ore is decreasing and is now less than 0.25 pct against a high of 0.77 pct- Crushing Operations The first stage of crushing is done under. ground where the oversize from I2-in. grizzlies is fed to a 56 X 72-in. jaw crusher. At the Selkirk shaft two 10-ton skips deliver the run of mine ore at a rate of 450 tons per hour to the 400-ton capacity shaft bins. One 6 ft wide Ross chain feeder and one locally made air-operated finger feeder feed the two 30-in. McCully crushers. Ahead of each crusher is a 6 X 9-ft spring grizzley spaced at 5 in. on a 35O slope. Neither the Ross chain feeder nor the finger feeder is entirely satisfactory and for the wet, muddy and sticky ore that has to be handled it is planned to replace these with two 6-ft wide apron pan feeders. The McCully crushers deliver a minus 5-in. product, at a.rate of over 500 tons per

Jan 1, 1949

By J. S. Aronofsky, H. J. Ramey

Potentiometric model studies of the five-spot water flood to determine the influence of mobility ratio upon injection or production histories are described. The results suggest a method for the correlation of data from field pilot tests for the estimation of an effective mobility ratio and its effect upon field water floods. The effect of the well spacing-to-well radius ratio upon production histories is presented. A method of accounting for this factor is suggested. The influence of injection (or production) rates and injection and production well pressures upon production histories is shown. The five-spot well pattern was investigated for water-to-oil mobility ratios of 0.1 to infinity. INTRODUCTION It has been well established that mobility ratio has an important effect upon flood patterns.1,2,3,4,5 It should be equally apparent that injection and production histories must also be influenced by mobility ratio. However, none of the articles referred to above mention the importance of being able to predict the effect of well pressures (or injection rates) during the entire time history of a waterflood operation. A complete description of production histories (the terms "injection" and "production" are synonymous for the steady-state model under consideration) would provide values for well pressures and interface positions at any time for a specified injection rate. conversely, if the waterflood problem is specified in terms of a constant injection well pressure, then it would be desirable to know the injection rate and interface positions at any time. This paper describes the results of potentiometric model studies which were used to analyze the influence of mobility ratio on injection or production histories. A method is presented for calculating production histories over a range of ratios of well spacing-to-well radius. The basic method described in this paper to evaluate production histories is to: (1) determine interface position as given in Ref. 1, and (2) measure electrical current and voltage drop for each interface position. It should be mentioned that the current state of knowledge on flood patterns as affected by mobility ratio shows that significant discrepancies exist between the results of various investigators2,3,4,5. It is beyond the scope of this paper to discuss the reasons for such discrepancies. However, the method of determining production histories presented in this paper could be applied to any of the swept-area patterns presented in the literature. All results given in this paper are based on a set of swept areas obtained by the potentiometric method. Potentiometric analyzer technique is adequately described in the literature, but the basic assumptions involved in work of this nature bear repetition. It is assumed that: 1. A distinct oil-water interface exists in the reservoir; only water is mobile in the region behind the interface (water zone) and only oil is mobile in the region ahead of the interface (oil zone). 2. There is a fixed mobility value, (k/µ) w associated

Jan 1, 1957

By Henry M. Stanley

The methods about to be described have been tested in practice, and are believed to be specially adapted to such extended topographical surveys as mining engineers in particular are sometimes called upon to execute. The assistance of Mr. H. 0. Flipper in the preparation of this paper, and his practical authorship of the second part, is hereby acknowledged. I. Photographic SuRveying. The writer was recently employed; together with Mr. H. O. Flipper, to survey the properties of the Plata-Reina de Sonora Mining and Milling Company, situated in the mining district of Las Planchas, District of Magdalena, State of Sonora, Mexico. These properties, now owned by an American corporation, of which M. W. Evans, of New Orleans, is president, and Richard A. Pomeroy is resident superintendent, are famous in the history of Mexican mining, as the place where planchus, or bolas de plata were foulld about the beginning of the last century. Ward, the English CILargh d7Affaires in Mexico from 1826 to 1828, writing at that epoch, says: "The idea [that the ores in the north of Mexico were richer than those in the south] probably originated in the discovery of the famous bolas de plata [balls of silver] of Arizona [Planchas de Plata de Arizona, a stock-ranch in northern Mexico], in the beginning of the last century, which was, and probably still is, believed in Europe to be one of those fables with which mining countries always abonnd. But the attention of the present government of Mexico having been drawn to the subject, a search was made in the viceregal archives, by order of the president, for the correspondence which was known to have taken place respecting it in the year 1736. This correspondence I have seen, and I have in my possession a certified copy of a decree of Philip the Fifth, dated Aranjuez, 28th May, 1741, the ohject of which was to terminate a prosecution, instituted by the Royal Fiscal, against the discoverers of Arizona, for having defrauded the treasnry of the duties payable upon the masses of pore silver found there. The decree states the weight of the balls, sheets and other pieces of silver discovered (bolas, planchas, y otras piezas de plata), to have amounted to 165 arroba, 8 pounds, in all, 4133 pounds; and mentions particularly one mass of pure silver, which weighed 108 arrobas (2700

Jan 1, 1892

By L. Sturkey

Quantitative X-ray diffraction studies of the precipitation of thorium in a Mg + 3.3 Th + 0.51 Zr alloy (HK31A) in both the as-cast and cold-worked states show that the precipitation may be described by f = 1 - e(t/T)1/2 over most of the aging period. The effects of cold work and temperature changes are determined. The precipitation of tile equilibrium Mg-Th compotund is Preceded by the formation of a transition phase of higher thorium content, with the cowposition Mg2Th and with a Laves-phase structure. Thorium-containing alloys of magnesium have assumed considerable commercial importance, especially for applications requiring exposures to temperatures greater than 500°F for appreciable lengths of time. The principal commercial wrought alloys in this system are HK31A, containing nominally 3 pet by weight thorium and about 0.7 pet by weight zirconium: and HM21A. containing 2 pet by weight thorium and 1 pet by weight manganese. These two alloys retain a high level of properties even after exposures of 100 hr at 600°F, while the more common alloys containing aluminum and zinc are badly overaged by these conditions. Therefore, in order to obtain some insight into the mechanism by which thorium produces high temperature stability in these wrought alloys, it seems desirable to investi- gate the effect of temperature and mechanical working on the precipitation processes involving thorium. Since the scattering power of a thorium atom for CuKa X-ray radiation is about ten times that for a magnesium atom, the magnesium alloys containing about 3 pet by weight thorium are ideal for quantitative measurements by X-ray diffraction of the amount of Mg-Th compound present at any time. Such quantitative measurements should be of theoretical importance in the study of the effects of time, temperature, and deformation on precipitation and precipitation hardening. Of the two commercial alloys, HM21A and HK31A, the latter is certainly the most suitable for study: In the Mg-Th-Zr2 system, only Mg-Th compounds need be considered, since no ternary compounds or binary Th-Zr3 and Mg-Zr4 compounds exist. The Zr is added to this alloy as a grain refining agent and probably plays a secondary role in precipitation. On the other hand. thorium and manganese form many

Jan 1, 1961