Search Documents

By H. W. Paxton, G. M. Pound

A method is outlined for taking into account variation in chemical potential of both components in evaluating capillary effects at growing interfaces. The results are compared with experiment, and seem to be in reasonably good accord for Widman-statten ferrite growing in austenite. ENERY pointed out that during the steady-state growth of phases with a rather small radius of curvature at their advancing edge capillarity cannot be neglected. By proper application of the Laplace equation a correction must be made to the activity gradients down which diffusion occurs. Subsequent workers have concerned themselves with attempts to evaluate specific cases by the use and modification of the principles laid down by Zener.2-5 To solve the problem in its simplest form it is necessary to assume thermodynamic equilibrium at the interface and to select some criterion which will allocate the available free energy between reversible and irreversible processes. Zener chose to assume that the division should be made such that the new phase grew at the maximum rate. Other workers have used the same2,3 or different assumptions, e.g., maximum rate of free-energy dissipation,4 minimum rate of entropy production.5 Li6 has proposed that the "thermokinetic potential" should be a minimum at steady state. The purpose of this presentation is to note that most prior treatments have considered variations due to capillarity only in the chemical potential of the mobile constituent, and that a more consistent treatment must involve a consideration of the variation of chemical potentials of both solute -and sol- vent in a binary system.* As an example, the way in which this arises for ferrite growing from austenite may be illustrated by reference to Fig. l(a). The line OABC shows a typical variation of carbon activity with composition at one atmosphere pressure (at a transformation temperature below A3). In the tip of a growing ferrite plate with a hemi-cylindricab leading edge of radius ?, the pressure due to capillarity is*

Jan 1, 1963

G. M. TAYLOR,* Colorado Springs, Colo.-The ore treated at the United Eastern is primarily a gold one and is cyanided-the counter-current decantation method being employed. One of our employees visited this plant a few months ago and, on his return, reported that the moisture in the tailing was carrying 20 c. per ton, which would appear to be somewhat high. As this type of plant has been advocated by one of the recognized cyaniding engineering firms in the country, and a number of these plants are in successful operation, it does not seem to me that the dissolved loss could be so high, and I would like to know if any one can give any definite information on this point? J. V. N. DORR, New York, N. Y.-I am very glad that Mr. Taylor has raised this question. When I first read Mr. North's paper and saw his statement, that they had an actual dissolved loss of 21.5 c. per ton, I was very much puzzled at this high loss which appeared avoidable by another decantation or the addition of a rotary filter. Reading it again, however, I noted that the actual dissolved loss of 21.5 c. given was evi-dently obtained by multiplying the assay of solution discharged from Z. thickener by the tonnage. On the basis of 283 tons milled per clay, this means $56.54 going to the clam. He states, however, that he returns from. the dam into the system, 70 tons daily assaying 40 c. per ton or $28 per day, so it would seem reasonable, unless I have overlooked something to regard the actual dissolved loss as $56.54 less $28 or $28.54, equaling 10.8 c. per ton. Even this loss, however, is much higher than good practice elsewhere, and can be accounted for largely by the tonnage being handled, which I believe is 30 per cent. above the capacity planned.

Jan 12, 1919

By H. F. Ramstad, F. D. Richardson

The equilibria (a) SiOz +Hz =SiO +H20 and (b) Si + SiO, = 2Si0 have beet1 studied at temperatures of 1425"to 1600°C ad 1310°to 1485°C respectively. The stattdard free energy changes for the tzrro reactions are given by the equatiotts Combination of the results for both equilibria leads to tiotz removes certain anomalies in existing high-terlzperature data for equilibria involving silica and silicon in iron. In many metallurgical processes and in many laboratory investigations silicon monoxide undoubtedly plays an important role. It is unfortunate therefore that wide differences exist between the results obtained by different investigators1-7 in their studies of such equilibria as In an attempt to put our knowledge of SiO on a surer basis, an exhaustive study has been made of equilibria [I] and [2] at temperatures ranging from 1300" to 1600°C. Reaction [I] was studied by measuring the amounts of silica which could be condensed from streams of Hz or Hz + HzO which had previously been brought into equilibrium with silica at temperatures ranging from 1425" to 1600°C. Reaction [2] was studied by measuring the material that could be condensed from streams of Hz or argon which had been brought into equilibrium with mixtures of silicon and silica at temperatures ranging from 1310" to 1485°C. EXPERIMENTAL Materials. The silicon was "superpure" grade and contained less than 0.1 pct impurities. The silica was prepared from pure mineral quartz; this was crushed and treated with concentrated hydrochloric acid to remove particles of iron, washed with water, and finally dried at 120°C. For the hydrogen + silica reaction, the silica was sized to —20+100 mesh. For the silicon + silica reaction, the two materials were ground to a fine powder in an agate mortar. The hydrogen and argon were commercial oxygen-free gases. The gas streams were controlled with capillary flow meters and the volumes were measured by wet gas meters. After passing through the meters, the gases were partially dried by silica gel. The hydrogen for the HZ + SiOz reaction was then passed through palladised asbestos at 300°C and dried with magnesium perchlorate. The efficiency of oxygen removal was checked throughout the experiments by passing the gas over an electrically heated strip of nichrome, used as an indicator as described by Rathman and de itt.' When mixtures of HZ + Hz0 were required, the partial pressures of water vapor (1.8 to 22 mm) were obtained by passing the hydrogen through oxalic acid dihydrateg' lo held at various controlled temperatures, O.l°C, by means of a water bath. The hydrogen for the Si + Si02 reaction was purified by passing it over a mixture of 3 parts of magnesium to 5 of lime heated to 600°."l1 u The argon for this reaction was passed through titanium powder (-3/16 in. + 100 mesh) heated to 900°C. The nitrogen used to prevent the reaction products escaping from the condenser (see later), was deoxidized by copper or iron at 600°C. All these gases were finally dried with magnesium perchlorate. Furnace, Temperature Contr01, and Measurement A molybdenum resistance furnace was used for both sets of experiments. The reactions were conducted inside a high-grade alumina tube, 36 in. long and 1 in. in diam as indicated in Fig. 1. With this arrangement an even temperature zone (2"C) 4 cm long was satisfactorily obtained. The temperatures were kept constant by means of a proportional controller actuated by a Pt-Pt 13 pct Rh thermocouple. This was placed between the two alumina tubes, so that the temperature at the junction was 1400" to 1450°C. Up to 1485"C, the temperatures were measured with Pt-Pt 13 pct Rh thermocouples. For higher temperatures an optical pyrometer was used, this being sighted (through the glass window 1 in Fig. 1) on the end of the alumina tube, that held the SiOz or Si +SiOz mixture, 10 in Fig. 1. The optical pyrometer was recalibrated whenever a change was made in any part of the apparatus situated in the hot zone. Successive readings with the optical pyrometer were reproducible to within 1"C. Equilibrium Apparatus and Procedure. Hydvogen and Silica Reaction. The apparatus is shown in Fig.

Jan 1, 1962

By J. Gordon Parr, G. R. Purdy

The phase boundaries of "TiNi" have been accurately determined by high-tewperature X-ray diffraction and metallo-graphic techniques. The phase (centered at 51 pct Ni) has a restricted range of homogeneity at 500°C, and a much greater range at 800°C. "TiNi" in all alloys containing less than 51 pct Ni decomposes rapidly and reversibly at 36°C to form a previously unreported phase. ThE region of the titanium nickel system corresponding to the phase "TiNi" has been the subject of several investigations.1,2,4-7 Laves and wallbaum1 reported "TiNi" as a body-centered cubic (a2) Phase, and Duwez and Taylor2 determined its para- meter to be 2.986. Duwez and Taylor also reported that "TiNi" decomposed into "Ti2Ni" and "TiNi3" on prolonged heating at 650" and 800°C, which led McQuillan3 to suggest a sluggish eutectoid reaction between "TiNis" and "Ti2Ni". Margolin, Ence, and Nielsen,' working with higher purity alloys, found no evidence of this decomposition. They showed the "TiNi" phase region extending from 49 to 54 pct*

Jan 1, 1962

By Earl Oliver

Page A.I.M.E. Stabilization Committee Activity................. 133 Definition of Capture Rule: Robert E. Hardwicke.......................... 134 Westmoreland Natural Gas Co. vs. DeWitt................ 135 Kelly vs. Ohio Oil Co......................... 135 Bernard vs. Monongahela Gas Co.................... 136 Definition of Ownership in Place..................... 137 Prospective Stabilization Remedies.................... 137 Dean Roscoe Pound's Four Teats of Practicability.............. 137 I. Mechanically Feasible....................... 138 Capture Rule.......................... 138 Ownership in Place....................... 140 Mechanical Separatio.7 Method................. 140 Engineering Appraisal Method................. 141 II. Economically Advisable...................... 143 Capture Rule.......................... 144 Ownership in Place....................... 144 III. Politically Wise.......................... 144 Capture Rule..........................144 Ownership in Place.......................147 IV. Legally Sound..........................148 Capture Rule..........................148 Ownership in Place.......................149 Dean Henry M. Bates' Analysis......................149 Raumé................................152 The A.I.M.E. Stabilization Committee was named in 1932 to ascertain whether some practical substitute could be devised for the Rule of Capture, which was generally credited with being the major cause of instability in the Petroleum Industry. After considerable intercommittee correspondence a letter was received from E. DeGolyer under date of Jan. 25. 1935. in which he discussed the possibility of modifying rather than discarding the Rule of Capture. He summarized his proposal as follows:

Jan 1, 1937

TO THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN Submitted herewith are the report of the Treasurer for the year 1937 and the reports for the same year of the following standing committees: Admissions, Membership, Papers and Publications, Library, Student .Relations, Speakers for Local. Sections and Student Societies, and Mining and Metallurgy. To these reports members are referred for further details. Finances.-Income for the year was the largest since 1930, the figure being $189,394, an increase of $18,803 compared with income for 1936, exclusive of a special Rocky Mountain Fund appropriation of $2500 in that year for visits to western schools and Local Sections. Major items of increase were: $8,000 from current dues and arrears; $7,700 from advertising in MINING AND METALLURGY and the two periodical "Technologies"; and $4,800 from sales of TECHNICAL PUBLICATIONS (pamphlets) and TRANSACTIONS volumes for both current and former years. Initiation fees and clues from new members declined $2,300, principally because of the larger 'proportion of Junior Members to Members among the new enrollments. Junior Members pay no initiation fee and dues are $10 compared with $15 for Members.

Jan 1, 1938

THE 127th meeting of the Institute was held in New York, Feb. 19 to 22, 1923. In addition to the usual large volume of technical matters under consideration, the meeting was particularly noteworthy for the amount of attention given to its business session; the convention of local section representatives also was full of interest. The total registration was 1201. The annual business meeting on Feb. 20, President Dwight presiding, was attended by 125 members, who listened with marked attention to the reports and addresses of the several officers. The chairman departed from the stipulated order of business in order to allow more time for the presentation of remarks on the state of Institute affairs. The previously pub-lished reports of the officers were accepted, as printed. On the report of the tellers, the following officers were declared elected: E. P. Mathewson, Director and President-District 0 T. T. Brewster, Director and Vice-president-District 6 Frank M. Smith, Director and Vice-president-District 11 W. H. Aldridge, Director-District 0 G. H. Clevenger, Director-District 1 A. N. Diehl, Director-District 3 Reno H. Sales, Director-District 7 Seeley W. Mudd, Director-District 10

Jan 3, 1923

By Hans Lundberg, Theodor Zuschlag

Based upon an instrumental improvement, a new development has taken place in the art of electrical prospecting, and some remarkable results have already been obtained with regard to potential exploration. In order to visualize the importance of this development, it is deemed advisable to review briefly the fundamental facts about potential surveys. Potential exploration may be carried out qualitatively or quantitatively. Qualitative investigations are made by determining and plotting on a map points of equal potential, whereby any anomalies are revealed, without, however, much clue to their magnitude. Quantitative investigations determine the variations of potential or potential drop, and thus show not only the location of the anomalies, but also their magnitude. Figs. 1 to 6 illustrate the influence of simple types of ground inhomo-geneities, assuming one effective exciter potential only. Such a condition can be closely realized by connecting an electric current source to two electrodes, one of which is located at a great distance. Assuming uniform ground resistivity, the resultant potential distribution mar be represented by concentric spheres. Any change from the normal condition causes a characteristic distortion of the spheres, which becomes different for different types of resistivity variation. The series of Figs. la to 6a illustrates schematically results of qualitative investigations and series lb to 6b results of quantitative investigations. Figs. 1 and 2 picture the well-known case of local resistivity variations normally encountered in ore prospecting. Figs. 3 and 4 show the reactions caused by more or less vertical resistivity contacts and Figs. 5 and 6 refer to the problem of ground-water and bedrock investigations where the resistivity contact is horizontal or nearly SO. It is evident from Figs. 5a and 6a that qualitative measurements do not permit an identification of such general geological features as widespread horizontal strata, because the resultant contraction or expansion of the equipotential circles at the surface cannot be recognized without quantitative determinations. On the other hand, qualitative measurements are well suited for the exploration of local or lateral resistivity

Jan 1, 1932

By James S. Browning

The Mineral Resources Institute and State Mine Experiment Station of the University of Alabama conducted Humphreys spiral tests on fine coal waste from nine preparation plants of Alabama strip mining operations to determine the feasibility of recovering low ash and sulfur fuel meeting steam coal specifications. The ash in the samples ranged from 9 - 5l%, and the total sulfur ranged from 0.4J- 2.39%. Continuous laboratory tests using a Humphreys spiral gave good recovery of the coal with excellent rejection of the ash and pyritic sulfur. Coal recoveries of 83.6 - 94.1% were achieved from the different samples. Ash content of the clean coal products fell within a range of 5 - 12.2%, with a total sulfur content of 0.62 and 1.10%. In quality, the products were comparable or superior to those now being shipped from the preparation plants.

Jan 1, 1980

By Parviz Montazer, Robert King, William Ubbes, Gideon Chitombo

This paper describes the results of a detailed study that was undertaken to define the spatial distribution of permeability within a five meter thick envelope around the CSM/ONWI room. Detailed fracture orientations and distribution were determined through mapping of the walls of the opening, logging of oriented core, and visual examination of borehole walls with a borescope and a T.V. camera. Over 3,500 measurements were made from which the three dimensional distribution of fractures was determined. Two principally different testing equipment designs and various methods of air injection tests were used in all boreholes to identify and characterize conductive fractures. Through analizing the distribution of permeability and fracture index around the room a zone of blast damage of approximately .5 m thickness was delineated. The effect of stress modification seems to extend farther into the host rock to approximately 3.5 m depth.

Jan 1, 1982

By R. J. Wasilewski

Electrical resistivity variation with temperature was measured on a series of alloys containting up to 33 at. pct of oxygen over the range 77° to1500°K. The resistivity behavior is highly anomalous and itzconsistent with simple metallic conduction. Both composition and temperature-depended resistivity singularities were observed. A few experiments carried out on Ti-N and Zr-O alloys indicate the presence of similar anomalies. These observations, together with the published data on effects of substi-tutional alloying on the resistiuity of titanium, suggest that the anomalies are inhevent in the electron structure of this group oj metals. The existence of two-band conduction, and a significant shift of bands relative to each other with temperature and/or the electron concentration are suggested. CONSIDERABLE advances have been made in recent years in the alloy theory of simple metals. Very little, however, is known about the bonding in transition metals and their alloys.&apos; Titanium, with its relatively few electrons, may be expected to show simpler alloying behavior than the more complex transition elements. Its alloys with the interstitial elements appear particularly attractive in an investigation of bonding characteristics because of a) the simple nature of the solute elements, b) the remarkable similarity between the equiatomic structures Tic, TiN, and TiO, and c) the extensive solid solubility ranges of oxygen and nitrogen in a titanium reported.2,3 The Ti-O system was chosen for the most extensive investigation because of the relative ease of preparation of suitable specimens. Since the main object of the work was to obtain data on the bonding and its changes on alloying, electron-sensitive properties were primarily investigated. The present work describes the investigation on the electrical resistivity-temperature-oxygen content relationships. A few experiments were also carried out at selected compositions in the Ti-N and Zr-O systems. EXPERIMENTAL Materials and Method. Polycrystalline specimens were prepared in the form of hairpin strips some 50 by 5 by 0.15 to 0.50 mm by direct metal-gas reaction. This was carried out by controlled oxidation followed by a homogenizing anneal at a higher temperature. All the test specimens were fully homogenized as judged from the uniform microstructure and microhardness. To avoid preferred orientation, each strip specimen was annealed in the ß range prior to the oxidation, this procedure assuring random orientation in the strip;4 hence any texture resulting from the oxidation reaction itself affected all the specimens to a similar extent. Titanium used was of high purity (66 DPN, 10 Kg load; major impurities 0,-43G ppm, N,-70 ppm, C-25 ppm, Fe-14G ppm). The solute content of the alloys was determined by weighing, after the reaction with a known amount of oxygen. The specimens in which the discrepancy between the volumetric and gravimetric measurements exceeded 2 pct (or 0.2 mg for the low oxygen alloys) were rejected. The mean between the two measurements was then taken as the oxygen content of the alloy. Check analyses showed no measurable nitrogen contamination. All oxygen contents are given in atomic percent. Zr-O alloys were prepared in identical manner from hafnium-free crystal bar metal, cold-rolled to strip 0.25 mm thick. Ti-N alloys required very long reaction times at the maximum temperature available (1250°C). In order, therefore, to detect possible oxygen contamination, duplicate specimens were reacted in every experimental run, and one of these was analyzed both for oxygen (vacuum fusion) and for nitrogen (Kjeldahl). Only the specimens in which the check analysis showed < 1000 ppm O were then used for resistivity investigation. Since only relatively high nitrogen alloys (7.1 at. pct; i.e., 2 wt pct N,) were investigated, this oxygen contamination was considered permissible. Dc resistance was measured by the four-probe method as previously described.= The temperature was determined with a calibrated thermocouple placed in the center of the specimen hairpin. The errors in the specimen resistance values thus obtained were estimated at 1 pct due almost exclusively to the finite thickness of the potential wires and the consequent uncertainty as regards the true resistance length of the specimen. For the calculation of the specific resistance, however, no dimensional measurements could be carried out on most of the

Jan 1, 1962

By Alan U. Seybolt

IN examination of some cold-rolled copper and cupronickel that contained a little columbium, it was discovered that these alloys were unusually resistant to annealing. This effect was sufficiently pronounced to warrant some investigation [ ] of the annealing characteristics of such compositions. EXPERIMENTAL PROCEDURE The alloys were made from cathode copper, electrolytic nickel, and a special copper-columbium hardener alloy furnished by the Electro Metallurgical Corporation. This hardener alloy contained 10 per cent columbium, with tantalum, aluminum and iron as major impurities. The melting was carried out in a clay-graphite crucible in a high-frequency induction furnace, under a charcoal or [ ] electrode carbon cover. No deoxidizing additions were made. The 7-lb. copper heats were poured into a steel mold, hot-rolled to ¼ -in. thickness, and annealed for ½ hr. at 760°C.; the cupronickels were annealed I hr. at 815°C. The material was then cold-rolled to a go per cent reduction in thickness and annealing tests were carried out on this 1/8-in. hard-rolled strip. A little silver was added to copper-columbium alloys 402 and 403 to find out

Jan 1, 1941

By R. Kossowsky

In the course of a study concerned with structural stability of precipitation hardening nickel base super -alloys after exposures to elevated temperatures, some interesting effects of hydrostatic pressure treatment on Rene were observed. The evidence presented below suggests that hydrostatic pressure treatment of the solution heat-treated alloy can affect the dispersion of the y&apos; (Ni3Al) phase upon subsequent precipitation heat treatment and long time aging. Rene 41 alloy has the following nominal weight percent composition: Al B C Co Cr Fe Mn Mo Ti Ni 1.4 0.006 0.7 11.3 19.2 1.0 0.05 9.4 3.3 balance The effect of successive pressure, precipitation heat treatment, and long time aging on the microstructure of this alloy was determined by subjecting a number of alloy buttons to five different thermopressure treatments. Pressure and precipitation heat-treatment parameters are listed in Table I. Fig. 1 shows y&apos; morphology* of specimens in groups I and 11. The treatment results in a fine dispersion with particle size on the order of 950 and 1350A, respectively, see Table I. Fig. 2 shows the morphology of y&apos; precipitate in

Jan 1, 1967

By C. D. Cochran, F. H. Deily, M. M. White, Victor Horner

A laboratory study of the effects of physical and easily measured rheological properties upon dynamic filtration was carried out. The purpose was to determine the factors affecting dynamic filtration and thus learn how to control this important property. The recommended procedure for determining the amount of fluid loss prescribed by API Code RP 29 "Field Procedure for Testing Drilling Fluids,"&apos; is very useful for mud conditioning purposes, but inadequate for comparing filtration properties of different muds under dynamic conditions. Where dynamic filtration control becomes important for purposes such as logging and coring, other means of evaluating filtration properties are needed. A special device and testing technique were developed to provide reliable data on filtration characteristics of different fluids under dynamic conditions. Liquid saturated rock samples were drilled with a microbit, and the amount of connate liquid displaced by the fluid being investigated was measured. The empirical testing procedure was considered reliable. A large number of laboratory-prepared and field-mixed dritling fluids with a wide range of physical properties were studied. These properties included: (I) shape of consistency curves, (2) apparent viscosity, (3) plastic viscosity, (4) yield value, (5) density, and (6) API filter loss. Test results indicate that very little, if any, trend could be established between changes in these fluid properties and dynamic filtration. INTRODUCTION During the process of drilling, excessive loss of liquid from the mud to the formation is undesirable for many reasons. Filtration can reduce production-zone permeability, cause sloughing of formations, affect electric log curves, and render the fluid data obtained from cores unreliable. Thus, it is very important that we gain a knowledge of the factors that control filtration. It is generally agreed that in any type of filtration (static, dynamic, or combinations thereof), the mechanics of filtering depend in great part upon the composition of the fluid. Moreover, it is also true that the physical and rheological properties are influenced by the composition of the fluid. Indirectly, then, it was hypothesized that a relationship existed between dynamic filtration and physical-rheological properties, two effects of a common cause—fluid composition. This paper discusses an attempt to relate filtration-while-drilling to physical and easily measured rheological properties. It is believed that the results of this study may prove useful to others in the industry who are working on the problem of understanding filtration. The industry accepted practice for determining fluid loss from drilling mud is described in API Code RP 29. The practice is to measure the amount of filtrate that passes during a given interval of time from a quiescent drilling fluid under applied pressure through a piece of filter paper. This is primarily a test of static filtration properties. Other investigators have studied filtration under dynamic conditions. Williams5 and Pro-kop5 studied radial filtration and filter-cake buildup by circulating fluid through a porous cylinder under conditions similar to actual mud flow. Nowak,4 Krueger,3,4 and Vogel3 studied the effect of filtration upon permeability by flowing mud past the face of rock Samples. In their tests, the bit action was simulated by mechanical scrapers that kept the filter cake from building up. Ferguson and Klotz2 studied three types of filtration: static, dynamic, and beneath-the-bit. They investigated each type separately, using a model well in which bottom-hole hydraulics and mechanics were closely approximated.

Jan 1, 1958

By F. Valton

In the number of the Engineering and Mining Journal for April 7th, 1877, Mr. W. P. Ward, of Cartersville, Georgia, explains in a very interesting manner, the results he obtained in the manufacture of ferromanganese in the blast furnace. These results may be summed up as follows : Production in the blast furnace of an alloy containing 67.2 per cent. manganese and 3 per cent. of carbon at most, with a utilization of the manganese amounting to 58 per cent. With the exception of the indicated proportion of&apos; carbon, which should be almost doubled to express the true state of facts, we would have had no observations to make on Mr. Ward&apos;s paper had he taken into account the results obtained in the same line in other centres of production. Before 1870, spiegel with 8 or 10 per cent. manganese only was known among blast-furnace products. In a journey to Sweden, in 1871,I ascertained that the Schysshyttan works manufactured regolarly a spiegel with 18 per cent. manganese. Later, at the Vienna Exhibition, in 1873, the Sava and Jauerburg works, in Carniola, presented to the jury a ferromanganese, obtained in the blast fur-

Jan 1, 1879

By John H. Hollomon

A REVIEW of the steps which have been made to increase knowledge in the field of ferrous physical metallurgy during the closing period of World War II brings both pleasure and disappointment. Contributions of great value have been made, to be sure. However, due partly to the stress of the times, researchers in this field have been in the main directing their attention toward the short-range problems involved in the development and production of materiel for war. Furthermore, publication of the results of a great number of studies has had to be delayed. Much of the German work may, indeed, be lost entirely, owing to the efficiency of our bombers, which managed to account for most of the famous Kaiser Wilhelm Institut of Dusseldorf, not to mention the other large laboratories and manufacturing plants throughout that country. It would seem safe to assume, however, that fundamental research in Germany had been forced to give way to the shallow, but more pressing, engineering problems of a country trying to avoid defeat. In Russia the picture has been clouded by the limitations imposed upon comunication; but this much does seem clear: Russia alone among the great nations of the world has maintained her long-range view and has continued to foster research of the most fundamental type. English workers; on the other hand, appear to have been able only to meet the demands of the pressing problems of war, and their studies have been of the short-range variety. That metallurgical research of any sort should have continued in France during this chaotic period in her history would seem impossible, but, amazingly, a small handful of scientists did manage to carry on their work, and it is to be hoped that more will be heard from them in the future.

Jan 1, 1946

Frank Firmstone, Easton, Pa. (communication to the Secretary*) : It may not be amiss to point out that the top-pressure in iron blast-furnaces is largely affected by variations in the temperature of the gas. I find in my note-books, cases in which the pressure was from 9.25 to 9.5 in. of water when the material in the furnace was low (after dinner-hour), which fell to from 8 to 8.5 in., when the furnace was again full, and the gas consequently cooled. The chief cause for this effect is, that, at the higher temperature, there is a decrease in the weight of the gas in the descending-leg of the siphon formed by the down-comer and the chimneys. It does not seem probable that there is any direct relation between top-pressure and quantity of flue-dirt. Top-pressure, at any given moment, measures the " head " necessary to discharge the gas then passing, against the resistances of pipes, valves, etc., in the gas-conduits between the top of the furnace and the mouths of the chimneys, and can be increased at will by closing, more or less, the valves, or dampers, at the stoves and the boilers. The question of relation between top-pressure and flue-dirt can be settled very easily by direct experiment, working alternately with gas-valves open, and partly closed, and noting the top-pressures and the respective quantities of fluedirt collected. The quantities of fine ore blown away, as shown by Mr. Grammer&apos;s tables, are astonishing to one who has had no actual experience with Mesabi ore and hard driving. Flue-dirt, in the sense in which he uses the term, was unknown at anthracite furnaces so long as the working was normal; when it did occur, it was always an incident of scaffolding and bad work, and was no doubt caused by an increase in the velocity

Jan 1, 1904

By Edward A. Sayre

In shaft sinking for cod mines, the cost item greatly influences the method adopted. This holds true especially when soft material must be traversed. The average life of a coal mine is short. This is due either to the limited area of the coal basin or to the great expense of maintenance and haulage underground when the entries are extended a considerable distance from the hoisting shaft. Therefore, the engineer in opening a coal mine is confronted with the fact that the cost must be kept within certain bounds else the venture will prove unprofitable. For this reason he may be prohibited from adopting certain safe, but expensive, methods that are used in sinking caissons for foundations, driving transportation tunnels, or other work of permanent construction. A common method of sinking through difficult ground employs the aid of a steel shoe pushed ahead of the shaft timbers. Another is the drop-shaft method. These two methods were used in sinking the main shaft and the air shaft of the Eagle No. 3 mine, at Des Moines, Ia., and the following data show the relative success and cost of the two methods of sinking under the same conditions. A drill log of the material to be penetrated was as follows (see Plate 1, Fig. 1): Thickness, Total Depth, Ft. In. Ft. In. Drift................................... 38 38 Sand..................................... 2 40 Drift.................................... 2 6 42 6 Jointed clay.............................. 5 6 48 Drift, firm............................... 10 6 58 6 Clay, with sand streaks.................... 3 61 6 Sand.................................... 12 73 6 Shale, with two thin beds of coal and thin strata of rock......................... 86 6 160 Rock.................................... 5 165 Coal..................................... 3 9 168 9 Main Shaft Sunk by Steel-Shoe Method This record shows the first 73 ft. to bc of drift material, the lower 12 or 15 ft. of which was sand. The remaining 92 ft. to the coal was shale and rock, and offered no trouble in sinking.

Jan 1, 1917

By R. A. Vandermeer, J. C. Ogle

Two distinct types of depth-dependent variations in texture have been observed in niobium cold-rolled various amounts up to 99.5 pct reduction in thickness. These nonuniformities are thought to be the results of nonhomogeneous plastic dewmation during rolling. The first type is characterized by a zone at intermediate depths that tends to lack certain strong orientations which are present in the surface and center layers of the rolled stock. This type of texture modification seemed to be associuted with "high" body rolling and may be related to the shape of the zone of deformation in rolling. The second type of texture inhomogeneity found involved the formation of a unique texture in the surface layers of heavily rolled strip. High fiiction forces between work piece and rolls appear to be needed to generate and maintain this texture. We believe that this unique surface texture results from a shear mode of deformation in the surface layers. THE evolution of texture in both the surface and center regions of cold-rolled niobium as a function of increasing deformation from 43 to 99.5 pct reduction in thickness was reported in a previous paper.&apos; It was noted that for strips rolled between 95 and 98 pct reduction a distinctly different texture appeared in the surface layers which was unlike the center texture. Certain other layer to layer textural variations were also detected during the experimental phase of that work but were not described in the paper. Surface textures have been reported previously for the bcc materials iron and Steel2-4 and are well known in the fcc metals.5 It is usually stated that these are shear textures which arise under conditions of high friction between specimen and rolls. Work by Mayer-Rosa and Haessner5 n niobium rolled under conditions presumed to be high roll friction gave no indication, however, of a surface texture in that material. This is indeed puzzling in view of our results.&apos; Thus we undertook additional experiments designed to study the stability of the surface texture for certain rolling variables. The variables investigated were the presence or absence of lubrication, amount of reduction per pass, and reverse vs unidirectional rolling. It is the purpose of the present paper to describe the kinds of depth-dependent textural inhomogeneities that we have observed in rolled niobium as well as to present the results of our recent experiments on the stability of the surface texture. Possible explanations for the depth-dependent texture variations will be discussed in terms of nonhomogeneous plastic deformation during rolling. EXPERIMENTAL Specimens cut from the niobium rolled to different reductions in the previous study1 were examined at various layer levels throughout the strip thickness for textural inhomogeneity. The specimen surfaces were either etched or machine ground and etched to remove material to a specific depth. Textures were determined by means of the Schulz X-ray reflection pole figure method with a Siemens texture goniometer and Cum X radiation. Since the important intensity peaks of the textures in niobium are usually located on the normal direction (N.D.) to rolling direction (R.D.) radius of the (110) pole figures, it was sufficient in many cases to scan only along this radius. At selected depths or where additional information was required the entire (110) pole figure was also obtained. In studying the stability and formation of the surface texture, experiments were conducted on 0.400-in.-thick, fine-grained, randomly oriented niobium specimens extracted from the same starting stock as that used in the earlier study.&apos; Two of these specimens were rolled at room temperature to a total reduction of 96.4 pct. One was rolled between cleaned and degreased rolls with no lubrication. The other was lubricated between passes with Welch Duo Seal vacuum pump oil. The rolling schedules of each were kept as nearly identical as possible. Drafts were of the order of 0.006 to 0.012 in. per pass. Other experiments consisted of rolling specimens at constant fractional reduction per pass, i.e., (ta- tb)/ta equals a constant where ta and tb are the entrance and exit thickness of the rolled stock, rather than at a constant draft, i.e., ta- tb equals a constant. Ten specimens were rolled at room temperature on a two-high, motor-driven rolling mill with 8-in.-diam rolls. These specimens were rolled to thicknesses of between 0.041 and 0.073 in. (82 to 90 pct total reduction) at approximately constant reductions per pass ranging from 9 to 45 pct. Kerosene was used as a lubricant. Half of the specimens were always rolled in the same direction while the other half were reversed end to end at each pass. The texture in the surface regions was determined with the X-ray technique described above. RESULTS The textural inhomogeneities noted in niobium rolled from fine-grained, randomly oriented stock 1.5 in. long by 0.75 in. wide by 0.40 in. thick can be classified into two types. The first may be discussed with the aid of Figs. 1 to 3. Fig. 1 is a three-dimensional plot of the X-ray intensity in units of times random vs f , the angle from the N.D. to any point along the N.D. to R.D. radius of the (110) pole figure, and depth, given as percent of the thickness (?t/to X 100, where at is the thickness of material removed and to is the as-rolled

Jan 1, 1970

By F. J. Tuck

THE Hayden mill of the Ray Mines Division, Kennecott Copper Corporation, is now equipped with two 9 by 12-ft. rod mills having a daily capacity of 6000 tons of coarse-crushing plant product from the mine. These two mills crush a 3/4-in. product to approximately 19 per cent on 14 mesh, with only one pass through the mills. Each rod mill has taken the place of four sets of 42-in. Garfield rolls with their attendant screens, and is making a product for the fine-grinding department comparable to that formerly made by rolls in closed circuit with screens. The rod mills are lined with wave-type liners of white iron, varying in thickness from 2 to 3 in. The shell and end liners last approximately 600 to 700 clays. Manganese-steel lifter bars, 3 5/8 in. thick, are used, spaced about 11 in. apart, and they give a life of 350 to 450 clays. Fig. 1 shows the general design and thickness of the wave-type liners and lifter bars; 1 1/2 -in. liner bolts are used to fasten the lifter bars to the shell. The shell liners are held in place by the tapered lifter bars. A ¾-in. wood hacking is used between the shell and the liners. The rod-mill scoop has removable manganese-steel lips, which last 250 to 300 days. The scoop proper has shown some wear in spots; and these spots have been protected by rubber bolted over them. Water and milk of lime are added to the elevator feeding the mill, but not enough water to cause a pounding of the rods against the shell. Roughly, the water added amounts to 2.5 to 33 per cent of the ore. Addi-tional water is added to the mill discharge to facilitate distribution to the classifier bowls in the fine-grinding department.

Jan 1, 1938