Search Documents

By F. J. Smit, S. C. Sun

Flotation variables were investigated for the re-clamation of phosphate from a Florida washer slime. Under optimum conditions, 92% of the phosphate was recovered. Further cleaning of the rougher flotation concentrate resulted in a product containing about 30% P2O5 with a phosphate recovery of 65%. The enormous amount of slimes rejected in the Florida pebble phosphate fields, containing roughly one-third of the phosphate in the pebble matrix,1 has long been considered as a serious problem to the industry. The mere disposal of these slimes has posed an almost insurmountable task for several investigators.2-5 Some companies still resort to huge surface dams, some covering 1800 acres, for slime disposal.6 Information on the recovery of fine phosphate from these slimes is scanty. Dry separation8 and electrostatic beneficiation8 were suggested, but would necessitate radical changes in the present mining and concentration methods. Haseman10 proposed the selective flocculation of colloidal phosphate with starch, while Ralston11 suggested the removal of clay from the matrix by amine flotation. Leaching of the slimes for recovering the small amount of uranium was attempted by the Battelle Memorial Institute12,13 but proved to be economically unfeasible. The purpose of the present investigation was to determine the optimum fatty-acid flotation conditions for reclaiming the phosphate discarded with the Bartow washer slime. Prior to the flotation experimerits, however, the size distribution and the minera-logical composition of the employed slime had to be determined.

Jan 1, 1963

By A. S. Koster, G. D. Rieck

X-ray experiments were carried out to show the occurrence of cylindrical texture in drawn tungsten wire. Only a small amount of (110) (110) cylindrical texture could he found in wires of intermediate thickness, i.e., of about 1.5 mm diameter. DRAWN wires of tungsten and other bcc metals like iron and molybdenum show a well-established (110) fiber texture. Now it might be conceivable that in drawing radial stresses remove the randomness of the crystallites around the [110} axis, thus giving a fiber texture of higher symmetry. In the resulting so-called cylindrical textures a specified plane normal coincides with the radius of the wire. Several authors discuss the occurrence of cylindrical textures in bcc metals. ~ieck' found no cylindrical texture in drawn tungsten wires of 165 n diameter. Leber~ states that in tungsten wires of 3 mm diameter a cylindrical {100)(110) texture is developed, which is gradually converted to a normal fiber texture by subsequent drawing. He also reported a definite cylindrical texture at the surface of iron wires. Peck and Thomas3 observed a nonuniform mode of deformation of the grains in transverse sections of heavily drawn tungsten and iron wires. According to Bhandary and cullity4 a swaged iron wire has neither a perfect (110) fiber texture nor a perfect {100}(110) cylindrical texture. It is clear that the concept of cylindrical texture in bcc metals still lacks a firm experimental basis. Leber's eviden~e,~ which seems to be the strongest, rests upon qualitative interpretation of photographs. The appearance of the 110 and 200 lines on the photograph of 3-mm wire, however, can be very well attributed5 to a normal ( 110) fiber texture superimposed on random background; our Fig. 1, giving a Debye-Scherrer diagram of etched tungsten wire of 180 p, is free of cylindrical texture according to all authors, but is quite similar to Leber's diagram. It was therefore decided to use a different method of X-ray texture determination on tungsten wires of diameters where cylindrical textures may be expected.

Jan 1, 1965

By J. C. Bayles

Jan 1, 1886

By Pol Duwez, Paul Pietrokowsky

The crystal structure of the compound TisGeS has been determined from X-ray powder diffraction data. Related silicon and tin compounds have been found to be isomorphous. Unit cell dimensions, axial ratios, and parameters for equivalent atomic positions are given. THERE is, at present, only meager information pertaining to the solid state reactions of titanium with the elements in group 4B of the periodic table (silicon, germanium, tin, and lead). The only two compounds whose crystal structure has been established are TiSi² and TiGe² (references 1 and 2 respectively). These two compounds are isomor-phous and have an orthorhombic symmetry D242h— Fddd. The titanium-rich regions of the constitution diagrams of titanium-silicon, titanium-tin, and titanium-lead have been investigated by Craighead et al.³ While valuable information concerning the alpha solid solubility of these three elements in titanium was obtained, no light was shed on the existence or nature of the titanium-rich compound in these systems. The present study is concerned with the crystal structure of the intermediate phases Ti5Si ?, Ti³Ge³, and Ti5Sn³, which were found to be isostructural. The alloys were prepared by mixing the pure metal powders in the desired proportions, pressing the mixture into pellets, and melting them in an electric arc furnace in the presence of a helium atmosphere.& After melting, the specimens, weighing approximately 5 g, were sealed in evacuated quartz vials, homogenized at 1038°C for three days, and quenched from that temperature. Powder diffraction patterns were made with a 143.2 mm diam Debye-Scherrer X-ray camera in which the Ievins and Straumanis film arrangement was utilized. Filtered copper radiation was used throughout the entire investigation. A study of the powder patterns of a series of alloys of various compositions indicated the presence of a compound around a composition corresponding approximately to a ratio of 3 titanium to 2 silicon, germanium, or tin. From a visual examination of the diffraction patterns, it was evident that the silicon and germanium alloys were iso- morphous. For small angle reflections, the powder pattern of the tin compound was analogous to that of the silicon and germanium compounds, but after the first ten reflections, the similarity was no longer clear. The powder pattern of the germanium compound was selected for indexing, since it exhibited a weak small angle reflection and clearly resolved doublets in the back-reflection range. Good agreement between observed and calculated values of (1/d)² was found by indexing the pattern on the basis of hexagonal symmetry. For the hexagonal system:

Jan 1, 1952

John Langton, New York, N. Y. (communication to the Secretary*):—In Mr. Firmstone's discussion (Trans., xli., 912) the formula he gives for the periodical payment—his equation (2)—may be simplified in form. The expression given by Mr. Firmstone is : q=S(l+ r) 1-(1+r)-(1+r) r which is a simpler form to use in calculations. Where S= principal to bc extinguished. Q = periodical payment or charge for sinking-fund, r = rate of interest per period (i. e., interest on $1 per period). n = number of payments or periods. Kent's Mechanical Enyineer's Pocket Book, under the heading Annuities, equation No. 5, gives : " The annuity which $1 will purchase for any number of ytlars n is * Received Jiily 16, 1911.

Jan 1, 1912

By D. H. Thompson, A. W. Tracy

Season-cracking is a type of failure of brass that results from the simultaneous effect of stress and certain corrodants. The object of this paper is to present data that will aid in a more complete understanding of the mechanism of season-cracking and related phenomena. Results presented show that certain high copper alloys are susceptible to season-cracking or stress-corrosion cracking, and possible explanations are discussed. Starting at least as far back as 1906, many papers have been devoted to this subject but the symposium1 held in Philadelphia in 1944 is the richest source of information. In order to study season-cracking, several of the many variables were held constant so as to learn the effects of others. Season-cracking is generally understood to refer to the corrosion cracking of brass having internal stresses;²,³ it is a special case of the general stress-corrosion cracking. Inasmuch as applied stresses are more readily produced and controlled, they were used exclusively in this research and the resulting phenomenon must he called stress-corrosion cracking.²,³ Only constant tensile stresses were used. The agents believed to be most frequently responsible for season-cracking are ammonia. amines and compounds containing then]. Both moisture and oxygen also appear to he necessary. Therefore, an atmosphere containing ammonia, water-vapor and air was selected for these tests. Briefly, the work consisted of exposing sheet metal specimens, having a reduced section ¼ by 0.050 in., of copper-base alloys to the effect of static tensile stresses between 5,000 and 20,000 psi and simultaneous contact with a. continuously renewed atmosphere containing 80 pct air, 16 pct ammonia and 4 pct water vapor at 35°C. The gas mixture and the speci- mens were maintained above the dew-point. The time-to-failure in minutes was the primary measure of results. In order to limit the experiment to finite time, it was considered that a specimen which had neither failed nor undergone microscopically detectable cracking in 40,000 min. (4 weeks) while under a stress of 10,000 psi or more could be considered immune to cracking. This is merely a convenient limit and is not to be considered proof of immunity. Supplementary tests in the absence of stress using weight loss or microscopical appearance as measures of attack were made. Apparatus The apparatus used in this research is shown in Fig 1. To facilitate the description it may conveniently be divided into six parts: stress-producing units, test chamber, gas train, electrical controls, timers and gas analysis device. A stress-producing unit is shown in an exploded view at the left in Fig 2. At the right is an assembled unit with a specimen in place in the lower portion; it is this part that remains in the ammonia atmosphere during a test. The upper part contains a spring, a central threaded rod, a large nut and necessary washers, pins, and so forth. Stress is produced in the specimen by screwing down the top nut against the spring, thus putting a tensile load on the central rod and so on the specimen. The wrench that turns the nut by extending through the upper cap, is seen at the upper right of the figure. The magnitude of the load is gauged by measuring from the pin that extends through the side of the tube, to a fixed point on the large flange. Measurement is made with a vernier beam caliper, shown at the right of the figure. The necessary spring compression to give a desired stress is calculated from the calibration curve of the spring and the dimensions of the specimen. The test chamber, center Fig 1, consists of a thermally insulated steel box 32 in. long by 10 in. high by 7 in. wide. A horizontal baffle reaching nearly to each end divides the chamber equally. Below this baffle are inlets for air and ammonia, a heating coil and a fan. Thus the gases are warmed and mixed in the lower level and flow past the specimens in the upper level. A thermo-regulator and thermometer project into the upper space. The top is pierced by 12 ports flanked by 3/8 in. threaded studs. A test starts when a port is opened and a unit containing a stressed specimen is thrust through it and bolted down against a neoprene gasket. The test chamber is held at 35°C. The gas train, right rear Fig 1, carries ammonia and air continuously to the test chamber. Tank ammonia passes through two reducing valves, a needle valve, a flow meter and into the test chamber. The air from either the plant compressor or a small laboratory compressor passes through wool towers and flow controls to the flow-meter. It then bubbles through water at 34°C and through a heated line to the test chamber. Electrical controls, left rear, Fig 1, provide rectifiers and mercury relays for the test-chamber and humidifier-heating-control circuits and outlets for

Jan 1, 1950

By T. C. King

AT the new Graham-Central Mill of Eagle-Picher, near Galena, Ill., material is simultaneously dewatered and introduced into the ball-mill scoop boxes by the use of variable-speed, 24-in. spiral classifiers. This arrangement has proved satisfactory in that the moisture content of the wet feed is reduced, thus allowing maintenance of density within the mills, and a constant feed at any desired rate to the mills is provided. In this mill the primary feed is wet crushed to minus 1/2 in. and preconcentrated by jigs to produce a bulk lead-zinc-iron concentrate and a waste tailing. The jig concentrate is then dewatered by a conventional dewatering classifier and stored in bins ahead of the ball mills. Even though this material is well dewatered, the discharge at the bin bottom is sloppy because of the gradual drainage of the water from the surface of the particles. Conventional belt feeders with vertical cutoff gates are unsatisfactory because of the flushing characteristic of the wet sand. The new installation employs 24 in. x 10 ft, 9-in. Simplex double-pitch spiral classifiers for feeders from the bin bottoms to the ball mill scoop boxes (fig. 1). These units are arranged with straight tanks and are driven by 5 hp motors through a U. S. Vari-Drive to provide a 4 to 1 speed ratio. Each bin discharges through a chute into the rising side of the spiral. The flushing characteristic of the material from the bottom of the bin is utilized to maintain a steady feed. A small amount of water tapped into the bottom of the bin insures uniform feed to the classifier. Excess clear water drains over the weirs. Feed rate to the mills is controlled by the variable-speed drives. The feed delivered by the spiral at a given speed setting is relatively dry, uniform, and steady, and as such is easily controlled by the operator. The classifiers are set on a pitch of 5 in. per ft and have a sand-raking capacity of from 8 to 32 tons per hr. It is believed that the solution of this problem offers possibilities for the storage of deslimed rod-mill sands and other similar products of the industry.

Jan 1, 1951

By T. C. King

AT the new Graham-Central Mill of Eagle-Picher, near Galena, Ill., material is simultaneously dewatered and introduced into the ball-mill scoop boxes by the use of variable-speed, 24-in. spiral classifiers. This arrangement has proved satisfactory in that the moisture content of the wet feed is reduced, thus allowing maintenance of density within the mills, and a constant feed at any desired rate to the mills is provided. In this mill the primary feed is wet crushed to minus 1/2 in. and preconcentrated by jigs to produce a bulk lead-zinc-iron concentrate and a waste tailing. The jig concentrate is then dewatered by a conventional dewatering classifier and stored in bins ahead of the ball mills. Even though this material is well dewatered, the discharge at the bin bottom is sloppy because of the gradual drainage of the water from the surface of the particles. Conventional belt feeders with vertical cutoff gates are unsatisfactory because of the flushing characteristic of the wet sand. The new installation employs 24 in. x 10 ft, 9-in. Simplex double-pitch spiral classifiers for feeders from the bin bottoms to the ball mill scoop boxes (fig. 1). These units are arranged with straight tanks and are driven by 5 hp motors through a U. S. Vari-Drive to provide a 4 to 1 speed ratio. Each bin discharges through a chute into the rising side of the spiral. The flushing characteristic of the material from the bottom of the bin is utilized to maintain a steady feed. A small amount of water tapped into the bottom of the bin insures uniform feed to the classifier. Excess clear water drains over the weirs. Feed rate to the mills is controlled by the variable-speed drives. The feed delivered by the spiral at a given speed setting is relatively dry, uniform, and steady, and as such is easily controlled by the operator. The classifiers are set on a pitch of 5 in. per ft and have a sand-raking capacity of from 8 to 32 tons per hr. It is believed that the solution of this problem offers possibilities for the storage of deslimed rod-mill sands and other similar products of the industry.

Jan 1, 1951

By Robert K. Waits

The resistivity, temperature coefficient of resistance, stability at 200°C, and structure of annealed Si-Cr films have been studied as a function of film cowposition. Colorimetric analyses of the films indicated 20 to 60 wt pct Cr over the resistivity range of 1 to 10-4 ohm-cm. Resistors were delinealed by photolithographic etching, contacted with aluminum, and mounted in TO-5 packages. The average temperature coefjicient of resistance, a, between 50" and 150°C is related empirically to the film resistivity, p, by a (ppm per °C) = -2900 - 1140 log p (ohm-cm). Near a resistivity of 3.5 x 10-3 ohm-ctn (30 at. pct Cr) , the temperature coefficient changes from positive to negative. The temperature at which the resistance maximum occurs increases with decreasing resistivity. The conduction mechanism between —196" and +360 C appears to have two components—an activated conduction dominating a1 lord chromium content and higher temperatures and a linearly temperature-dependent conduction dominating at high chromium content and low temperatures. Electron diffraction patterns showed the films to consist of Cr3Si and amorphous silicon. Resistors thicker than 150A typically drifted less than 0.6 pct after 5000 hr stor-age at 200°C. Resistors as thin as approxinzately 80°A that had a silicon overlayer showed similar stability. Such films had sheet resistivities of 10 kilohm per square and temperature coefficients near —600 ppm per "c. THIN-FILM resistors having sheet resistivities greater than 1 kilohm per square are required in many integrated circuit applications. A process for producing such resistors should be compatible with present circuit fabrication and packaging, including exposure to maximum temperatures of 300° to 570°C during contact alloying, die-attach, and ceramic package sealing. In addition, the resistors should have a low temperature coefficient of resistance and change less than 1 pct during storage at temperatures up to 200°C for 1000 hr or longer. Reports of work beginning in 1949 at Battelle Memorial Institute indicated that, among other materials, the silicides of chromium, Cr-Co, molybdenum, tantalum, and tungsten were worthy of further study as high-stability resistive films. Later work on Si-Cr films vacuum-deposited by flash evaporation from a tungsten boat1 led to the conclusion that Si-Cr had "excellent properties for development into high- stability ... resistive elements". More recently, Si-Cr films have been vacuum-deposited from a tantalum boat,2 from a BeO-coated tantalum boat,3 by flash evaporation from an electron-beam-heated tungsten Source,4 and by triode sputtering.5 This paper describes a study of Si-Cr films vacuum-deposited by electron-beam heating of Si-Cr alloys. Resistivity, temperature coefficient of resistance, stability at 200°C, and structure were studied as a function of film composition. EXPERIMENTAL PROCEDURE Film Deposition. Si-Cr sources were prepared by vacuum-melting pressed pellets of mixtures of powdered chromium (99.9 pct, -100 mesh, Lunex Co., Pleasant Valley, Iowa) and silicon (99.99 pct, -325 mesh, United Mineral and Chemical Co., New York). A permanent-magnet focused electron-beam gun having a water-cooled copper crucible was used to heat the pellet until complete melting occurred. The mixture was then kept molten for an additional 5 min. The alloy thus formed was used as the source material for Si-Cr film depositions using the same electron-beam gun. Pieces of semiconductor-grade silicon ingots were used as sources for silicon depositions. The films were deposited within a standard vacuum evaporator having an 18-in.-diam Pyrex bell jar, a liquid-nitrogen-cooled trap, and a Consolidated Vacuum Corp. 6-in. diffusion pump containing Dow Corning DC-705 pump fluid. The substrates were thermally oxidized* silicon wafers 2 to 2.5 cm in diam. The

Jan 1, 1969

By N. A. D. Parlee, E. M. Sacris

OXYGEN solubility in liquid silver has been well studied.1-6 It has been established that the solubility follows Sieverts' law reasonably well5'6 up to po2

Jan 1, 1968

By W. C. Coons, E. H. Rennhack, R. A. Perkins

THE constitution of Ti-N alloys containing up to 17.5 wt pct N has been investigated by Palty, Margolin, and Nielsen.1 Their results, which confirmed earlier work

Jan 1, 1969

By Jei Y. Choi, P. G. Shewmon

The surfrrce-diffusion coefficients (DJ for Aulg8 on (100) and (111) surfaces of copper have been determined between 1050" and 780°C using a new avuzlysis imd experimental procedure. The results are: D, has also been determined fm cua4 at 870°C, and the values found are 4.5 times larger than those measured by the grain boundary grooving technique for the same surface orientations. This difference is felt to result from the approximate nature of the mathematical solution used in the present work. Attempts to measure D, for silver on copper and silver surfaces indicated a means of matter transport different from surface diffision was dominant in moving tracer from the source out over the surface. Cnlculations and experiment both indicate that this is the flow of silver through the vapor phase which completely masks the much smaller flow due to surface diffusion. The previous self-difhsion studies of D, for silver and copper are discussed in terms of our own analysis and found to yield values of D, factors of lo5 or more greater than those found by the grain boundary grooving tech -nique. UNTIL about 5 years ago it was widely believed that the activation energy for surface diffusion, AH, , was less than that for grain boundary diffusion, AHb,, which in turn was less than that for diffusion through the lattice, AHz.' This was concluded from various evidence that D,> Db>Dl, and one tracer study of D, for silver on silver from which AH, was inferred.2 In 1959 Mullins and Shewmon demonstrated that D, could be determined from the kinetics of the growth of grain-boundary grooves.3 Using this procedure, Gjostein measured D, on copper between 800" and 1050°C and found that the activation energy was roughly equal to AHl .4 Subsequent work on copper,5" silver,',' and goldg between the melting temperature T, and 0.87 T, confirmed that AH, as determined using the grain boundary grooving or scratch-relaxation technique was equal to or greater than AHz. During the same period, Drew and Pye again determined AH, for silver on silver using a tracer techniquelo and a mathematical solution similar to that of Nicker son and arker.' Though the values of D, Drew and Pye measured at any given temperature were about 200 times smaller than those reported by Nickerson and Parker, they again found a low activation energy of about 10 kcal, or about one fifth that found at the higher temperatures with the mass transport technique. A distinguishing characteristic of these two previous tracer studies is that they have worked at low temperatures (-1/2 T,) where they felt volume diffusion was negligible and then analyzed these data as if all tracer atoms leaving the source flowed out into and remained in a homogeneous high-diffusivity surface layer of undefined thickness. This is totally different from the model used in the mass-transport studies or the studies of grain boundary diffusion, which assume the high-diffusivity surface layer to be only a few angstroms thick. If this latter model is applied to the earlier tracer studies, it is shown that the tracer has really pe!etrated into the lattice a mean distance of 1000A. Thus the tracer distribution observed after an anneal is thought to be due to the combined effects of surface and volume diffusion. Independent of the relative validity of the two models, it seems evident to us that any comparison of the values of D, as determined in these two ways is meaningless and misleading, since the values of D, and AH, obtained in these two ways would be totally different for the same physical distributions of tracer. Once the fundamental difference in the approaches of the two techniques is established, we are faced with the question of which model better approximates physical reality. Here all the evidence seems to be on the side of the ''thin surface layer" analysis. In fact, the authors of Refs. 2 and 9 do not argue for the "thick-layer model" we have described; they simply invoke it through the equation they use to calculate D, . The primary evidence for the thin-film approach is: a) grain boundary grooves and scratches widen in proportion to tU4 and Mullins' rigorous analysis shows that this is only valid for a surface layer which is quite thin relative to the width of the groove;11 b) all accepted or seriously discussed models of solid-vapor interfaces and high-angle grain boundaries assume that the disturbed region of the interface is at most a few a0 thick. With the above in mind, it was desirable to determine D, using a radioactive tracer and a "thin-

Jan 1, 1964

Geological and Natural History Survey of Minnesota, Minneapolis, Minn W. H Emmons, Director A list of publications will be sent upon application Orders for publications should be addressed to The University of Minnesota Press, Minneapolis, Minnesota The Geological Survey of Minnesota has a record of long and useful service Some of the papers published have been outstanding in their field A series of 24 Annual Reports, covering the years 1872 to 1895-98, inclusive, was issued, of which 16 are still available at a price. More important however, are the six volumes of Final Reports, in which is collected the material presented in the earlier Annual Reports. All the strictly geological papers are found in four of the volumes of the Final Reports. vol 1 (1872-1882), principally geology by counties, 2 (1882-1885), same as 1, 4 (1896-1898), same as 1, 5 (1898-1900), Structural and petrographic geology Prices for each volume, leather $3, cloth $2 50, excluding postage, unless other directions accompany the order, volumes of the Final Reports will be sent express collect. A series of Bulletins has been issued, of which a few are out of print. Considering only those available, and of greatest interest, they are: Bulletin 5, Natural gas in Minnesota, by N H Winchell (1889), 50 cents, 6, Iron ores in Minnesota, their geology, discovery, development, qualities and origin, by N H Winchell and H V.

Jan 1, 1933

By AIME AIME

Air transport supplants the old methods. The 3-piece canoe fits in the plane and likewise makes possible not a bad division of labor over a 5-mile portage

Jan 1, 1933

By F. M., Waring

F. M. WARING,* Altoona, Pa.-The necessity for conserving tin has recently been very forcibly brought to the attention of all consumers, and efforts are now being made to reduce the tin content in certain alloys or to substitute other alloys not containing tin. The approximate composition of the non-ferrous alloys in general use on the Pennsylvania Railroad are given in the accompanying table. Phosphor bronze is used principally for rod bushings, main-rod brasses, and crosshead shoes. Ex. B bronze is used to a small extent for backs of car and coach bearings, but the majority of these are now made of the car-journal bronze, which contains, on the average, about 5 per cent. tin.

Jan 12, 1918

By Thomas V. Falkie, Robert Stefanko

Recently The Wall Street Journal featured a series of articles titled "The Dirty Work-Brutal, Mindless Labor Remains a Daily Reality for Millions in The US.-Mining Coal, Shoveling Slag, Gutting Hogs Pays Bills But Can Drain Spirit, Hope." The article was devoted to describing how tough and dangerous is mining (and some other jobs) and how rough life is for miners and their families. Similarly during the past few years some psychiatrists and sociologists have devoted increased attention to the attitudes and life styles of miners. Unfortunately most of their approaches have been neither scientific nor objective, and very little good clinical research has been done on the subject.

Jan 1, 1971

By A. R. Rosenfield, G. T. Hahn

The effects of adding 0.025 volume fraction of uniformly dispersed Tho2, particles (particle size -380A) to iron have been examined. The two-phase alloy is shown to have a lower transition temperature and higher cleavage stress than either the base metal or a solid-solution alloy (Fe-3Si). Enhanced cleavage resistance is thought to be a consequence of particles limiting the effective slip distance of dislocations and thus the ability of Pile-ups to act as stress concentrations. Further calculations predict that the highest cleavage strengths are attained with uniform dispersions, where the particle size is kept small (-250A) and the volume fraction is relatively large (-2 to 3 pct). ALTHOUGH a fine dispersion of second-phase particles is known to impart strength to an alloy, the possibility that it might also impart ductility has only recently been explored. Outstanding progress has been made in the production of ductile tungsten alloys containing Tho21,2or (Hf, Zr)C,= but the contribution of the dispersion to ductility has neither been optimized nor fully analyzed. The basis for such an analysis has now been developed1,5 and is discussed briefly below. Experiments on iron are also described that attempt to isolate one of the possible ductilizing mechanisms and test its effectiveness. In analyzing these experiments, it is important to remember that cleavage obeys a stress criterion, and that either a lower ductile-to-brittle transition temperature or a higher cleavage stress is evidence of enhanced resistance to cleavage. DUCTILIZING MECHANISMS Slip Blockage. Cleavage fracture of polycrystals may be initiated at the intersection of a slip band (or twin) and a neighboring grain or a large (-1 to 5 µ) particle. The slip band generates a stress concentration at its head, and either the grain boundary fractures, the particle fractures, or cleavage is initiated in a neighboring grain. Experimental evidence for this viewpoint is found in metallographic studies8-8 and from the observation that cleavage is usually preceded by yielding.8-11 The potency of a slip band as a stress concentrator

Jan 1, 1968

By J. Gross

G. H. Clevenger, Chairman of the Milling Methods Committee of the Institute, made the following introductory remarks: "Several years ago, a number of us felt that the time was ripe for a fundamental investigation of crushing and grinding. At the outset, it appeared that the first thing we needed was a yardstick whereby grinding efficiency could be measured. "The U. S. Bureau of Mines has been most generous in cooperating with the Milling Methods Committee in getting this work well under way. John Gross, who served the committee for a year as secretary, was placed in charge of the investigation and has been ably assisted by S. R. Zimmerley. "Messrs. Gross and Zimmerley will now present the Progress Report covering their work to date." PROGRESS REPORT J. Gross, Salt Lake City, Utah. -This has not been a simple problem, and when I tell you that we can give you a verbal report of what we have done during three years in five or ten minutes you will realize that we have necessarily done a great deal of work that does not appear in the final results. We have been in a virtually new field. Therefore, we have had to feel our way at each step so as to be fairly sure we were correct. The first thing that was realized in this problem was that unless we had some method of measuring what happened when we crushed an ore, we might as well quit and not go further. We realized that if we tried to measure the results of crushing or grinding by the ordinary sizing test we would not get anywhere. We could sieve down to say 200 mesh fairly accurately; we could even go one sieve size further with a little less accuracy, and then we were absolutely lost, unless we went into microscopic measurement. Even this latter method would not have been satisfactory. The question was: what were we going to measure? If we were going to measure size, we might measure one particular dimension of a particle and be off 200 per cent. or more. If we tried to measure surface, we would have something tangible; the surface of a particle, no matter how irregular, is something definite, far more definite than any linear dimension would be. Moreover, if we could measure surface, we would immediately have a method of checking the Rittinger law as to whether it was or was not correct. So the first thing that we sought was a method whereby we could measure surface on crushed particles or, we will say, on particles; it would not make any difference whether crushed or not. It then became a question of what kind of particles we were going to use in obtaining a method for surface measurement. We realized that it would be rather a com-

Jan 1, 1928

By H. R. Thresh

An oscillational vis cometer has been constructed to measure the viscosity of liquid metals and alloys to 800°C. An enclosed cylindrical interface surrounds the molten sample avoiding the free surface condition found in many previous measurements. Standardization of the apparatus with mercury has verified the use of Roscoe's formula in the calculation of the viscosity. Operation of the apparatus at higher temperatures was also checked using molten lead. Extensive measurements on five different samples of zinc, of not less than 99.99 pct purity, indicate i) impurities at this level do not influence the viscosity and ii) the apparatus is capable of giving reproducible data. The variation of the viscosity ? with absolute temperature T is adequately expressed by Andrade's exponential relationship ?V1/3 = AeC/VT , where A and C are constants and V is the specific volume of the liquid. The values of A and C are given as 2.485 x 10-3 and 20.78, 2.444 x 10-3 and 88.79, and 2.169 x 10-3 and 239.8, respectively, for mercury, lead, and zinc. The error of measurement is assessed to be about 1 pct. Prefreezing phenomena in the vicinity of the freezing point of the zinc samples were found to be absent. AS part of an over-all program of research on various phases of melting and casting nonferrous alloys, a systematic study of some physical properties of liquid metals and their alloys was undertaken in the laboratories of the Physical Metallurgy Division.1,2,3 The most recent phase of this work, on zinc and some zinc-base alloys, was carried out in cooperation with the Canadian Zinc and Lead Research Committee and the International Lead-Zinc Research Organization. One of the properties investigated was viscosity and the present paper gives results on pure zinc; the second part, on the viscosity of some zinc alloys, will be reported separately. Experimental interest in the viscosity of liquid metals has virtually been confined to the past 40 years. The capillary technique was already established as the primary method for the viscosity of fluids in the vicinity of room temperature; all relevant experimental corrections were known and an absolute accuracy of 1 to 2 pct was possible. Ap- plication of the capillary method to liquid metals creates a number of exacting requirements to manipulate a smooth flow of highly reactive liquid through a fine-bore tube. Consequently, the degree of precision usually achieved in the high-temperature field rarely compares with measurements on aqueous fluids near room temperature. However, the full potential of the capillary method has yet to be explored using modern experimental techniques. As an alternative, many investigators in this field have preferred to select the oscillational method. Unfortunately, the practical advantages are somewhat offset by the inability of the hydrodynamic theory to realize a rational working formula for the calculation of the viscosity. In attempting to overcome this restriction many investigators have employed calibrational procedures, even to the extent of selecting an arbitrary formula for use with a given shaped interface. However, where calibration cannot be founded on well-established techniques, the contribution of such experiments to the general field of viscometry is questionable. A critical appraisal of the viscosity data existing for pure liquid metals reveals a somewhat discordant situation where considerable effort is still required to establish reproducible and reliable values for the low-melting point metals. The means of rectifying this situation have gradually evolved in recent years. Here, the theory of the oscillational method has undergone major advances for both the spherical and cylindrical interfaces. The basic concepts of verschaffelt4 governing the oscillation of a solid sphere in an infinite liquid have been adequately expressed by Andrade and his coworkers.5,6 Employing a hollow spherical container and a formula, which had been extensively verified by experiments on water, absolute measurements on the liquid alkali metals were obtained. The extension of this approach to the more common liquid metals has been demonstrated by culpin7 and Rothwel18 where much ingenuity was used to surmount the problem of loading the sample into the delicate sphere. Because of the elegant technique required to construct a hollow sphere, the cylindrical interface holds recognition as virtually the ideal shape. On the other hand, loss of symmetry in one plane increases the complexity of deriving a calculation of the viscosity. The contributions of Hopkins and Toye9 and Roscoe10 have markedly improved the potential use of the cylindrical interface in liquid-metal viscometry. The relatively simple experi-

Jan 1, 1965

By M. Guney, A. R. Bell

In Mindola mine on the Zambian Copperbelt, there is a plan to extend the current production level of 1.2- 1.5 km (3,900-4,900 ft) with five additional production levels. Research work indicated that the present total heat output of 38.6 MW will inevitably increase to 63.2 MW in 25 years. Estimated WE and DB temperatures, representing the total heat generation in stope faces and development headings during these same periods are predicted to increase to 33.8/40.2°C (93/104°F) and 35.3/42.1°C (95/108°F) respectively. It is assessed that the nominal refrigeration capacity needs to be progressively increased to 9,000 M W.

Jan 1, 1984