Search Documents

By N. A. Gjostein

From their study of the anisotropy of grain boundary mobility in aluminum, the authors conclude that tilt boundaries have a higher mobility than twist boundaries because the atomic misfit at the pure-twist boundary is relatively small compared to the misfit at a tilt boundary for a given amount of misorientation. If this is true, then one would expect a twist boundary to have a lower grain boundary energy than the corresponding tilt boundary. Fig. 6, taken from the work of Gjostein and Rhines,10 shows that this is indeed the case for [001]-cu tilt and twist boundaries in the high-angle region, thus lending support to the authors' conclusion.

Jan 1, 1968

By I. C. Edwards, G. E. Agar

INTRODUCTION Many research efforts over the past years have been devoted to the study of energy consumption in comminution and the characteristics of the broken material. The old "laws" have been superseded by more general methods of analysis1,2,3 but these methods have not received much attention outside the laboratory. The work to be described here was done in order to obtain scale-up information on wet rod milling of sylvinite. EXPERIMENTAL A 30 x 51 in. Denver rod mill with a scoop feeder was used for these tests. Ore was fed from a variable speed screw conveyor into the feed box along with saturated brine. The mill was filled to approximately 45% of its volume with 2400 lbs of a mixed rod charge. The minimum possible feed rate was 2.5 tph and the practical maximum for this mill was 8 tph. Individual tests were run by setting the solid feed rate, then adjusting the brine flow rate to give the desired pulp density. After steady state, as evidenced by constant discharge pulp density, had been reached, samples of the discharge were taken at 15-minute intervals. These samples were filtered, washed with alcohol, dried, then screened on Tyler screens using a Ro-tap shaker. The sylvinite feed was regular plant feed that had been scalped at 20 mesh and was tapped from the coarse ore bins. It had been previously passed through a roll crusher set at 3 inches and after scalping was essentially minus 1 in. plus 20 mesh. RESULTS The screen analysis of samples from each series of tests was plotted on double logarithmic scale paper to determine the reliability of the series. In some cases, a faulty sample or screening procedure dictated that the results of one test be discarded. The criterion is a simple one — if the slope of one plot was noticeably different from the others in the series, it was discarded. The only cases that caused difficulty were those in which the brine was not thoroughly displaced from the solids. When this occurred agglomerates were easily identified on the screens and the whole of the sample was retained on 3 or 4 screens. There were no border line cases. The number N given in Table 1 is the number of size analyses that were pooled to form the data shown in Fig. 1. While examining the reliability of the sizing and sampling by plotting the data, it became apparent that there was no significant difference between grinds made at 50 and 60% solids. For the analysis given here, these tests were regarded

Jan 1, 1967

By K. E. Manchester, C. B. Sibley

The feasibility of doping silicon to produce device structres by directly implanting impurity atoms has been demonstrated. Both phosphors and boron ions have been successfully implanted in silicon to produce electrical junctions. Junctions as deep as 1.2 p have been produced by phosphorus ions having energies the order of 80 kev. An electromagnetic separator has been used to controllably produce uniform, large-area implantations for evaluation experimentation. Correlations between junclion depths and ion energies huve been obtained. Orientation effects have been observed and it has been found that the (110) direction is the easy direction for implanting. Monitoring of thermal treatments oj implanted substrates by sheet-resistance measurement indicates a very mild thermal anneal removes most of the damage done during the implantation. These indications are further substantiated by reverse-current measurements of j,inctions Produced by implantation. Electrical characteristics of implanted junctions are compared with those of diffused junctions. We have been interi n the interaction of energetic ions in the III-V groups, in particular boron and phosphorus, with single-crystal silicon to produce type conversion for possible device use. A number of investigators, a few of whom are avies, Kornelson,3 and so forth, have reported on penetration of energetic ions into both amorphous and crystalline solids. While most work has been done with ions of the rare gas and alkali metal groups, some work has been reported by ing, erber,' and others6 in which ions of the 111-V groups have been implanted in single-crystal silicon. A large amount of this work has been done with ion energies in the 100-kev to 1.5-Mev range. An excellent review article has been written by caldin. We have concentrated on ion energies which are in the 10 to 80 kev range, with which over 1500 implanted junctions such as the one shown in Fig. 1 have been produced in silicon substrates with both phosphorus and boron ions. Fig. 1 is a 3-deg angle lap in which the n type area produced by 66 kev P is delineated and the junction is 9500A below the surface. EXPERIMENTAL Implantations reported in this paper were made with the ion source adjusted to produce ion currents in the range of 1 to 2 pa with accelerating voltages varied from 10 to 40 kv. When using doubly charged ions this produced 10 to 80 kev ions. This allowed substrate temperatures to remain below 100°C. Sam- ple movement resulted in beam impingement angle variation of 7 deg from the normal to the substrate surface. Substrate resistivities have been varied through the range of 0.001 to 500 ohm-cm and specimens oriented in three directions, (110), (Ill), and (loo), within 12 deg. RESULTS For the purpose of this paper, discussion of results will be limited to phosphorus implantations with mention of results for boron-implanted silicon. Similar results have been obtained for boron and will be reported at a later date. In Figs. 2, 3, and 4 depth penetration is shown

Jan 1, 1967

By John Chipman, Peter J. Koros

The distribution of copper between liquid silver and liquid iron, Fe-C, and Fe-C-Si alloys was studied at 1600°C. From the data and the activity of copper in silver obtained from the phase diagrams, the activity coefficients of copper in iron up to 3 atomic pct are log y, = 0.90 — 2.4 N, and y": = 8.0. The effect of carbon up to saturation is expressed as log y = 1.8 Ni. The effect of silicon up to 11 atomic pct is insignificant. SLOWLY rising copper content of steel being produced is focusing attention on the lack of information on the behavior of copper in liquid steel. Chou' measured the activity coefficient of copper in liquid iron through its distribution between liquid silver and iron. He obtained a value of 9.12 at infinite dilution. Chipman' calculated the activity coefficient of copper in liquid iron at 1600°C from the phase diagram and obtained a value of 12. Ameiln and Pfeiffer- investigated the possibility of removing copper from liquid steel through the use of lead, silver, and bismuth as solvents. They also calculated that the activity coefficient of copper in liquid iron would be increased five or sixfold by addition of 4 pct C. Langenberg and Lindsay' are investigating the effectiveness of lead and sodium sulfide in removing copper from liquid iron. The experimental method was similar to that used by Chou' and Chipman and Floridis." Silver, copper, and iron were melted together, the copper distributing itself between the two layers so that at equilibrium a,.,, (in Ag) - a,.,, (inFe) and N,.,, (in Ag) yc,, (inFe) (in Ag). [21 N,.,, (inFe) Thus, from the concentration of copper in each layer and the activity coefficient of copper in liquid silver, the activity coefficient of copper in liquid iron can be calculated. The effect of an alloying element such as carbon on the activity coefficient of copper can also be determined from its effect on the distribution, provided the new element is essentially insoluble in silver. The one serious limitation of this method is the increasing mutual solubility of silver and iron in the presence of a third component. The mutual solubilities of pure iron and silver are negligible, but increase with increasing copper concentration beyond the range investigated. Ag-Cu System—The activity coefficient of copper in silver at 1600°C had to be estimated, since direct experimental data are not available. Kawakami" measured the heat of mixing of Ag-Cu alloys at 1200°C by a calorimetric technique. Scheil' calculated the heat of mixing in this system by use of the phase diagram, assuming that the solution is random and that the heat of mixing is independent of temperature. The terminal solid solution may be assumed to obey Raoult's law within the requirements

Jan 1, 1957

By W. C. PAGE

HARVEY S. MUDD has the unusual distinction of having virtually inherited a Directorship in the -A.I.M.E., for he was appointed to the Board to fill the unexpired term of his father in 1926. Since then he has served as a Director continuously until 1936, and now he is a candidate for Vice-President. One of the first words that young Harvey tried to say was "ore," for he was born in Leadville, Colorado, in the heyday of that camp, where Seeley W. Mudd for years ran the Small Hopes mine. Stanford and Columbia gave him his mining education, and the Shattuck-Arizona, at Bisbee, his first job. Afterwards he examined many

Jan 1, 1937

By AIME AIME

SHORTLY after he started his professional career, the subject of this sketch acquired the sobriquet "Moose" Allen. At the time he was engaged in geological exploration it1 the Canadian wilds. The nickname was given .him because of the wide, straight trail that he broke with unusual speed when going through the bush. Like a moose he was strong, energetic, and determined. To a considerable degree, Rolland Craten Allen today displays the same characteristics in larger affairs-business, civic, and professional. It is his habit to study a problem thoroughly, to decide u11on the best course of action, and then to pursue that course with vigor and

Jan 1, 1936

By R. M. Goldhoff, J. W. Spretnak, R. Speiser

IT has been observed by Grange and Garvey' that the homogenization of boron-treated steels could lead to complete elimination of the hardenability effect caused by boron. The experimental conditions leading to this conclusion involved the heating of steel specimens with and without boron at 2350°F for 24 hr. To prevent oxidation and decarburization, the specimens were encapsulated under vacuum in silica tubes. This observation of permanent deterioration of boron effect was noted in both a 0.63 pct plain carbon steel and a 0.25 pct C low alloy steel, both of which had been treated with ferroboron and homogenized at 2350°F for 24 hr. In another series of boron-treated steels which had been homogenized for shorter times, the effect was to reduce, but not completely eliminate, the boron effect. Under these circumstances, it was presumed that longer heating times would cause permanent deterioration of the boron effect in this series of steels also. Since the characteristic grain boundary constituent could not be formed in any of these steels after homogenization, it was concluded that possibly boron was being converted into an ineffective form through chemical combination resulting from prolonged heating at high temperatures. Assuming the validity of this observation, a series of experiments to establish the relationship between temperature of homogenization and kinetics of deterioration was contemplated. Initially an attempt was made to reproduce the results just described. For this purpose commercial lots of AISI 8640 and AISI 86B40 steels were used. The analyses of these steels appear in Table I. Hardenability evaluation was on the basis of the hardness of normalized sections. Grange and Garvey' pointed out that these steels are air hardening to some extent and such a technique can be used. For these tests the specimens were held for 20 min in a salt bath at 1600°F and then cooled in still air. Several evacuated silica capsules containing pairs of the test steels were made up and heated for 24 hr at 2350°F. A number of failures occurred among these capsules, but evaluation of the specimens successfully treated indicated a complete deterioration of the boron effect. However, examination of the surface of the treated specimens showed that some reaction, probably with the silica tube, had taken place, since none of the specimens was bright. One further test was made at 2350°F for 12 hr, using a pair of specimens wrapped in tantalum foil prior to encapsulation. These specimens appeared bright after treatment, and their hardenability evaluation showed that no deterioration had taken place. Since these steels are extremely sensitive to de-boronization at high temperatures and particularly at long times of holding, the experimental observations raised some doubt as to the real occurrence of the permanent deterioration effect. To resolve this question an experiment was undertaken in which the high temperature portion of the treatment was completed in vacuum. For this purpose a molybdenum wound resistance furnace capable of maintaining good vacuum was used. All the pertinent accessories to this furnace were machined from molybdenum stock in order to withstand the high temperature involved in the experiment. With this equipment a temperature of 2400 °F was obtained and held under a pressure of 5x10-" mm Hg for 24 hr. A specimen of each of the two test steels was suspended in the furnace and both were heated simultaneously. Temperature was measured with a standardized Pt—Pt-13 pct Rh thermocouple, whose millivoltage at 2400°F was extrapolated from the standardization equation, good up to 2200°F. The complete evaluation of these specimens is shown in Table 11. The hardness values attained by each steel after normalizing, both before and after the prolonged high temperature treatment, remain the same. A microscopic study of the decomposition products present in the microstructures of specimens at various points in the heat treatment correlated with the hardness values observed. It seems that no permanent loss of boron hardenability effect occurs, at least in these Grainal-treated steels, when deboronization is circumvented. Acknowledgments This work was conducted under the sponsorship of the Aeronautical Research Laboratory, Wright Air Development Center, under Contract No. AF 18(600)-94, and their support and permission to publish is gratefully acknowledged. A note of thanks is also extended to the Republic Steel Corp. for supplying the materials used in the work. References ' R. A. Grange and T. M. Garvey: Factors Affecting the Harden-ability of Boron Treated Steels. Tro.ns. ASM, 1946, vol. 37, p. 136.

Jan 1, 1957

By C. E. Van Orstrand

An intrusive body is a mass of igneous rock that has migrated upward, presumably from great depths. Great variations in form, composition and depth of burial occur. It is not proposed in this paper to go into all of the details of the problem. Instead, it mill be assumed here that the intrusive has the form and characteristics represented in Fig. I. According to W. 11. Emmons minerals are not deposited in appreciable quantities below the "dead line." Important amounts of ores of virtually all metals may be found around summit cupolas, but only gold, copper and zinc (in limited quantities) are usually associated with trough cupolas. Most students of ore deposits agree that temperature changes are largely instrumental in precipitating many ores in the "hood" and that the difference in temperature between the intrusive and that of the country rock may be the chief factor in determining the mineralogy of a deposit. A problem then of some interest is to correlate the principal physical features of the intrusive with the phenomena of heat conduction as evidenced by the cooling curves and the isothermal surfaces. Mathematical Theory In order to show the possible application of heat conduction to the interpretation of the processes of metalliferous deposition associated with intrusives, it will be as- sumed that the intrusive is a large par-allelopiped of dimensions, 2l, 2m, 2n. The equation that represents the flow of heat from the parallelopiped into country rock (v = o, 1 = o), which has the same thermal properties as the intrusive, is2,3 l-x v I FT 2 [2 2 — l-x m — y — m — y n — z In this equation, the origin, x = o, y = o, z = o, is at the center of the parallelopiped. v = temperature at point x, y, z, time 1. v, = initial temperature throughout the intrusive, 1 = o. k = coefficient of thermal diffusivity. a, ß, y are variables of integration. Put n = m in Eq. I, and we have v I [2/5 [2I-x 2 — l-x m — y 2 2 2 kt 2 20xt e-a2da ebrdß

Jan 1, 1946

By C. E. Van Orstrand

An intrusive body is a mass of igneous rock that has migrated upward, presumably from great depths. Great variations in form, composition and depth of burial occur. It is not proposed in this paper to go into all of the details of the problem. Instead, it mill be assumed here that the intrusive has the form and characteristics represented in Fig. I. According to W. 11. Emmons minerals are not deposited in appreciable quantities below the "dead line." Important amounts of ores of virtually all metals may be found around summit cupolas, but only gold, copper and zinc (in limited quantities) are usually associated with trough cupolas. Most students of ore deposits agree that temperature changes are largely instrumental in precipitating many ores in the "hood" and that the difference in temperature between the intrusive and that of the country rock may be the chief factor in determining the mineralogy of a deposit. A problem then of some interest is to correlate the principal physical features of the intrusive with the phenomena of heat conduction as evidenced by the cooling curves and the isothermal surfaces. Mathematical Theory In order to show the possible application of heat conduction to the interpretation of the processes of metalliferous deposition associated with intrusives, it will be as- sumed that the intrusive is a large par-allelopiped of dimensions, 2l, 2m, 2n. The equation that represents the flow of heat from the parallelopiped into country rock (v = o, 1 = o), which has the same thermal properties as the intrusive, is2,3 l-x v I FT 2 [2 2 — l-x m — y — m — y n — z In this equation, the origin, x = o, y = o, z = o, is at the center of the parallelopiped. v = temperature at point x, y, z, time 1. v, = initial temperature throughout the intrusive, 1 = o. k = coefficient of thermal diffusivity. a, ß, y are variables of integration. Put n = m in Eq. I, and we have v I [2/5 [2I-x 2 — l-x m — y 2 2 2 kt 2 20xt e-a2da ebrdß

Jan 1, 1946

By John V. Beall

Monotonous flood planes flanked either side of the road as we drove in the embassy car from the airport to downtown Seoul. We crossed the brown waters of the Hann River, meandering over mud flats. A great, gnarled tree bore beautiful fall colors of gold. "That is a Ginko Tree, the oldest living fossil, probably a hundred million years old;" said Jean W. Pressler. Compared to other cities of the Far East, the traffic in and around Seoul was sedate. Few motorcycles or bicycles, and little superfluous horn tooting. "This is the best season in Korea. We have long beautiful springs and falls," said Pressler, chief of the mining branch of USAID, and he continued with a briefing on the country.

Jan 8, 1969

Jan 1, 1971

By AIME AIME

MANY interesting papers, opportunity of seeing o1d friends, and an exposition showing all that is latest in equipment, all were factors in bringing a large crowd to Detroit during "Metal Week," October 2-6. The Institute's Iron and Steel and Institute of Metals Divisions held technical sessions at the Statler Hotel on October 4 and 5, and that hotel was also headquarters for the American Society for Steel Treating and the American Society of Mechanical Engineers, both of which also had technical sessions. The American Welding Society and the Wire Association met at the Book-Cadillac Hotel, and the exposition was staged at Convention Hall, out Woodward Avenue. All in all it was a big week for men interested in metal working. One of them stated to your reporter on the train en route to Detroit that this was the one convention that he never missed, and doubtless others felt the same way about it.

Jan 1, 1933

United Engineering Trustees, Inc C E Reistle, Jr (to Oct '55), A B Kinzel, '56, Andrew Fletcher, '57, Philip Kraft (from Oct '55 to '59) The Engineering Foundation W M Peirce, '56, A M Gaudin, '58 Engineering Societies Library Board Frank T Sisco, '58, C H Behre, Jr Engineering Societies Personnel Service Board of Directors E J Kennedy, Jr, E H Robie Advisory Committee, Milwaukee F T Agthe Special Survey Committee C M Cooley American Standards Association Mining Standards Board E R Borcherdt, '55, Otto Herres, '55, J K Richardson, '56, E W Bullard, '56, Alternate

Jan 1, 1955

United Engineering Trustees, Inc James L Head, '55, E C Meagher, '56, Gail F Moul¬ton, '57 Advisory Committee to Real Estate Committee Cleveland Dodge, Herbert Hoover, Paul D Merica The Engineering Foundation W M Peirce, '56, A M Gaudin, '58 Research Procedure Committee A M Gaudin, March '54 Engineering Societies Library Board Frank T Sisco, '54, E M Wise, '56, James L Head, ex officio Engineering Societies Personnel Service Board of Directors E J Kennedy, Jr, E H Robie

Jan 1, 1954

By B. D. Lichter

In a previous paper, Oelsen, Schuermann, and Hey-nertl pointed out the possibility of obtaining complete thermodynamic functions for alloy systems from calorimetric measurements alone. Specifically, if the heat content of a heterogeneous, multicomponent system is known as a function of temperature and composition, then it is possible to derive the heats, entropies, and free energies of formation of liquid phases and of solid intermediate phases of fixed composition. The authors present equations and graphical techniques applicable to eutectic systems and systems with intermediate phases without solid solubility at lower temperatures. eijering has considered possible extension of the treatment to systems with complete solid-state miscibility at lower temperatures; however, experimental difficulties practically restrict the method to systems with very limited miscibility in the solid state. The purpose of this note is to present an alternative derivation of the heats and entropies of formation of liquid phases and of solid intermediate phases from heat-content measurements alone. Fig. 1 shows three types of phase diagram to which the analysis may be applied. If the heat content is determined as a function of composition x, at temperature T, we have quite generally and the heat of mixing of the liquid is obtained directly from heat-content measurements. If the temperature T lies in a two-phase region (solid-liquid) then

Jan 1, 1967

[United Engineering Trustees, Inc. A. L. QUENEAU, '45 ALBERT ROBERTS, '47 RALPH B.. WILLIAMS, '48 The Engineering Foundation F. F. COLCORD, '46 E. A. PRENTIS, JR., '48 A. L. QENEAU, '45, Chairman Engineering Societies Library Board J. W. LAIST, '48 W. A. MUDGE, '45 A. B. PARSONS, Ex-officio T. T. READ, '46]

Jan 1, 1946

"Acta Metallurgica" Dennis Carney, '59 Alfred Noble Joint Prize Committee F B Foley, Dec '61 American Association for the Advancement of Science F T Agthe, Dec '59, William L Fink, Dec '60 American Geological Institute Arthur Montgomery, Oct , '59, F C Kruger, Oct '60 American Power Conference J P Weir, T D Hess American Society for Testing Materials

Jan 1, 1959

"Acta Metallurgica" Robert Madden, Dec '60 Alfred Noble Joint Prize Committee F B Foley, Dec '61 American Association for the Advancement of Science William L Fink, Dec '60, H K Ihrig, Dec '61 American Geological Institute F C Kruger, Oct '60, Thomas L Kesler, Oct '61 American Power Conference Howard A Herder

Jan 1, 1960

"Acta Metallurgica" William C Ellis, Dec '57 Alfred Noble Joint Prize Committee Same as Rossiter W Raymond Award Committee AIME American Association for the Advancement of Science 0 B J Fraser, Dec '57, J T MacKenzie, Dec '58 American Geological Institute H A Meyerhoff, Oct '57, Charles F Park, Oct '58 Committee on Government Relations J L Gillson, '56 American Power Conference M Tenenbaum, '57 American Standards Association Mining Standards Board E R Borcherdt, Jan '57, Otto Herres, '57, J K Richardson, Dec '56, Alternate E W Bullard

Jan 1, 1957

[United Engineering Trustees, Inc. ALBERT ROBERTS. '47 R. M. ROOSEVELT, '49 RALPH B. WILLIAMS, '48 The Engineering Foundation F. F. COLCORD. '46 M. A. PRENTIS. Jn.. '48 It. >I. ROOSEVELT. '49]

Jan 1, 1946