Search Documents

By Charles R. Keyes

A COMPLETE transformation has taken place in the boras industry during the year 1908. A most remarkable factor in this radical change in method of producing the crude borates has been its removal from the realm of industrial chemistry to the field of mining. With the development of extensive deposits of borate-minerals interstratified in thick sequences of Tertiary clays and sands, their winning becomes a strictly mining-enterprise, of the same kind and of the same certainty as the digging of coal or iron-ore. The major supply of the world's production of commercial borax now comes from the United States. While formerly all of the boric salts of commerce were laboriously extracted from the waters of saline lakes of the arid regions, or from the bottom-salts of desiccated ponds, it later was largely slowly leached from ancient desert shales and clays. During these periods the borax industry was a very hazardous and expensive vocation.

Oct 1, 1909

By George W. Sears

In preparing this symposium, our ambition was to elicit authoritative expression of opinion concerning important selected phases of the industry from men active in it. Responses to requests for contributions were gratifying, especially so in view of the short time available. The generous and cooperative spirit of the industry as a whole is amply evident. Responses were received from the following, who are therefore the true authors of the paper: W. G. Adamson, General Manager of the pershin; Quicksilver Co., Lovelock, Nev.; Dudley Baird, Vice President, Pacific Foundry Co., San Francisco; Walter W. Bradley, State Mineralogist of California; W. D. Burcham, General Manager of the Brewster Quicksilver Consolidated, Terlingua, Tex.; William Forstner, San Francisco; H. W. Gould, of H. W. Gould & Co., San Francisco; Marcus Hulings, General Manager of the Chisos Mining Co., Terlingua, Tex.; Frank J. Katz, Chief Engineer, Division Mineral Statistics, United States Bureau of Mines, Washington, D. C.; Lloyd J. Lathrap, Superintendent, Nevada Quicksilver Mines, Inc., Lovelock, Nev.; W. R. Moorehead, General Manager, New Idria Quicksilver Mings, Inc., Idria, Calif.; F. W. Oakes, Jr., Terlingua, Tex.; C. N. Schuette, San Francisco. Brief Economic History of Quicksilver in the United States Quicksilver ore was first discovered in the United States at what was later the New Almaden mine in California, in the year 1824. Production also began here, but not until 1850, when it was stimulated by the active demand caused by gold-mining operations. Prospecting for quicksilver was active, high-grade ores were found and ample production lowered the price from $100 per flask in 1850 to about half that figure for the greater part of the next 10 years. During the succeeding decade, many new quicksilver mines were found; production increased at a time when the local demand diminished, so that most of the product was exported. The third decade of quicksilver mining in the United States witnessed the development of the pan amalgamation process, particularly in Com-stock silver-mining operations. A suddenly increased demand sent prices soaring, the all-time peak of quicksilver production followed, and the highest price was soon replaced by the lowest one on record. Huge quantities of quicksilver were exported between 1870 and 1880 and exports continued in decreasing measure for three decades to 1910. In

Jan 1, 1930

By C. W. Parmalee

The ideal fuel for burning ceramic wares is the one that, among other characteristics, has little or no sulfur. For that reason wood was long considered the most desirable fuel but its high cost has practically eliminated its use except in regions where it is very abundant or other circumstances warrant its choice. The fuels commonly employed are natural and producer gas, oil, and coal. The last named is undoubtedly the most important, not only in this country but abroad. Occasionally anthracite is used but the larger part is bituminous. The quality of the coal used depends on the kind and the value of the products being manufactured. For some materials, such as common brick, hollow block, etc., the quality of the coal is of less importance than in the manufacture of polychrome terra cotta, pottery, porcelain, etc. It is obvious that in burning clays that contain notable amounts of pyrite, marcasite or gypsum, as is the case with many common clays, the sulfur content of the fuel is of much less importance. The permissible amount of sulfur in the coal used will depend on the kind of product being manufactured. "A good sample1 of coal commonly used in pottery ovens has something like this quantity of sulfur: total sulfur, 1.20 per cent.; sulfur in ash, 0.11 per cent.; volatile sulfur, 1.09 per cent." This is based on English pottery practice. Correspondence with a. number of leading manufacturers in this country has produced the following figures: Sanitary Ware.—(a) 1.0 per cent, maximum, (b) 0.5 per cent. Sewer Pipe.—(a) 1.2 per cent., (b) 1.1 per cent, present run, 3.0 per cent, has been used. Terra Cotta.—(a) 0.5 per cent, basis of contract, 1.0 per cent, approximate. Pottery.—1.0 per cent, contract, 1.5 per cent, probable content. Enameled Brick.—1.3 per cent, maximum, (a) and (6) designate different firms giving figures. Since a pottery kiln for sanitary ware will require about 14 tons of coal for a bum, the quantity of SO2 that will be generated from a 1-per

Jan 1, 1920

By Robert Ammon

The milling practice at Mascot, at present, consists of dry crushing to % in., jigging, fine grinding, and flotation. The ore arrives at the mill from two mines, No. 1 mine shaft being located in the mill proper, and No. 2 mine shaft being situated about 2000 ft. east of the mill. No. 2 mine is served by a coarse-crushing plant and aerial tramway to the mill bins. In jigging the No. 2 mine ore, 50 per cent. of the mill feed is rejected by the jigs as a jig tailing ranging from 5/8 in. to 10 mesh; the balance of this ore, after removing a jig concentrate, is ground to flotation feed. In jigging No. 1 mine ore, approximately 80 per cent. of the mill feed is rejected as a coarse jig tailing, and the balance is ground to flotation feed without the removal of a jig concentrate. The difference in the treatment is due to the fact that No. 2 mine ore carries a higher content of zinc than that from No. 1 mine. Of the total concentrates produced, 30 per cent. is made on jigs and 70 per cent. by flotation. At present, 1350 tons of No. 2 ore and 800 tons of No. 1 ore are treated each 24 hours. The recoveries for a typical week are as follows: Heads.......................... 3.55 Jig concentrates................ 61.30 Jig tails......................... 0.80 Flotation concentrates........... 60.60 Flotation tails................... 0.09 Extraction..................... 86.50 The associated minerals are a straw-colored sphalerite, dolomite, calcite, pyrite, quartz, and a small amount of greenockite, which occurs as a stain and sometimes small crystals along with sphalerite, but is comparatively rare. Pyrite is present in small quantities, usually less than 0.5 per cent.; quartz occurs in bands a few inches thick. A complete analysis of the ore is as follows: PEr Cent. Per Cent. Calcium carbonate.............. 48.11 Zinc sulfide.................... 5.43 Magnesium carbonate........... 35.36 Cadmium sulfide............... Nil Silica.......................... 8.73 Lead sulfide................... Nil Alumina....................... 1.04 Iron oxide...................... 1.33 Total....................... 100.00

Jan 1, 1925

By Nicholas J. Grant, Italo S. Servi

THE creep and stress rupture properties of three grades of aluminum have been reported in a previous paper.' It was found that the stress coefficient of the creep rate and of the rupture time changes at the transition from low temperature-type to high temperature-type deformation. The transition corresponds to the equicohesion for grains and grain boundaries. In order to support the conclusions obtained from the examination of creep and stress rupture data, the deformed specimens were observed metallographically and a few special tests were conducted. The results of these qualitative observations are given in the present paper. Experimental Procedure and Results Table I gives the types of aluminum specimens.' The creep and stress rupture tests were conducted in simple tension at constant stress. Further details on the experimental techniques have been given.' The test bars were electropolished in a perchloric-acetic mixture before testing and were observed after testing without any further preparation unless otherwise specified. Observations of specimen cross-sections were made after electrolytic polishing and etching. The samples were extended along a direction parallel to the longer side of the micrographs of Figs. 12 through 27. The log-log plots of stress vs. minimum creep rate for the three grades of aluminum appear in Figs. 1 and 2. The reference numbers on each curve help relate the photographs to the conditions of testing, indicating where high temperature-type deformation and failure prevailed and where low temperature behavior prevailed. Deformation of Single Crystals at Very High Temperature: An annealed, high purity aluminum specimen was slightly strained at one end and re-annealed. A large single crystal was formed at the strained end of the specimen during re-annealing; the other end remained polycrystalline (see Fig. 3). A stress of 50 psi was applied to the cold specimen to avoid loading at 1100°F. The temperature was then raised to 1100°F, kept at 1100°F for 3 hr, and lowered again to room temperature. Fig. 4 shows the appearance of the specimen after testing. The single crystal deformed by gliding along parallel planes, while the polycrystalline part deformed mainly by grain boundary flow. Some grain growth occurred in the polycrystalline part. Another high purity specimen, which had two large single crystals at the two ends and a polycrystalline zone in the middle portion, was tested at 1000 °F under a stress of 100 psi. The appearance of the sample after test is shown in Fig. 5. Even though considerable slip occurred in the single crystals, the fracture occurred in the weaker polycrystalline portion. Evidence of Grain Boundary Migration during Creep Testing: A high purity, coarse grained specimen, which had a large crystal in the middle portion (see Fig. 6) was tested at 700°F under a constant stress of 175 psi for 30 hr. The appearance of the specimen after testing (Fig. 7) indicates that the large crystal deformed by gliding along parallel planes, while the rest of the specimen deformed mainly by grain boundary flow. Microscopic examination showed clear evidence of grain boundary flow and grain boundary migration, an example of

Jan 1, 1952

By K. D. Hester, A. W. Fletcher

A nickel-copper sulphide concentrate was treated in a pilot plant at Warren Spring Laboratory during 1961, by a hydrometallurgical roast-leach-solvent extraction process devised to cleanly separate the metal values and produce acid sulphate liquors containing the metals. It is shown that 86 pct of the nickel and 95 pct of the copper could be leached from the calcine, after a sulphatizing roast on finely ground flotation concentrate. Iron was removed from the leach liquor by limestone neutralization with a small loss of values. Copper and nickel were separated by solvent extraction with naphthenic acid in kerosene after partial neutralization of the iron-free liquors with ammonium hydroxide. Hydrogen sulphide and chlorine were used to remove zinc (and residual copper) and cobalt impurities respectively. The recovery of pure copper and pure nickel, by electrowinning, from the acidic solvent extract strip liquors finally produced, appears technically feasible. An economic analysis of production costs shows that small, geographically isolated, nickel-copper sulphide deposits cannot usually be worked profitably by established processes. The requirements for profitable operation on a comparatively small scale could possibly be met by a flotation-roast-leach process. Two difficulties, obtaining satisfactory extraction of nickel from a sulphide concentrate and separating the copper and nickel in solution, have prevented the previous use of this method. A solution to the first problem, dissolution of the nickel, was described in a recent paper by Thornhill.1 It was shown in this paper that copper and nickel in a flotation concentrate could be oxidized to water soluble sulphates by roasting in a fluidized bed with added salt cake. Workers at the Warren Spring Laboratory have shown that the separation of copper and nickel can be accomplished by solvent extraction using a relatively inexpensive carboxylic acid, naphthenic acid. Moreover, the mineral acid required to strip values from the loaded solvent could be produced, and the metals recovered, by electrowinning; thus the latter section of the process was regenerative. The removal of iron from the leach liquor and the elimination of impurities such as zinc and cobalt before nickel electrowinning would be necessary to complete the flowsheet. The process under investigation could therefore be summarized (Fig. 1) as follows: 1) Flotation to produce a bulk sulphide concentrate. 2) Fluidized bed roasting to sulphate the nickel and copper minerals. 3) Leaching of roaster calcine to extract soluble nickel and copper. 4) Precipitation of iron from the separated leach liquor by air oxidation after the adjustment of pH and temperature. 5) Recovery of copper from the iron-free Liquor by pH adjustment and liquid-liquid extraction. 6) Purification of the copper raffinate by removing zinc and residual copper as insoluble sulphides and cobalt as cobaltic hydroxide. 7) Recovery of nickel from the purified liquor by pH adjustment and liquid-liquid extraction. Laboratory and pilot plant studies detailed below, were carried out at the Warren Spring Laboratory, to test the feasibility of each one of the unit processes and to obtain preliminary plant design data. FLOTATION The ore was an altered basic rock containing concentrations of magmatic sulphides.

Jan 1, 1964

By R. L. Bowron

GROWING use of basic slag in the agricultural industry is of special interest and importance to the iron and steel industry of the Birmingham district, providing an increasing outlet for this by- product. Such use of basic slag was first developed in England about fifty years ago where it soon became wide- spread. About twenty years ago the Tennessee Coal, Iron & R. R. Co. began its production in the United States after exhaustive tests had demonstrated its high value here as in Eng- land. It is particularly valuable on heavy clay and acid soils, improving their physical condition, increasing their alkalinity where that is desirable, and providing soluble phosphate and small amounts of manganese to soils deficient in these respects. Its use in agriculture is growing as its advantages are becoming more widely known.

Jan 1, 1937

INDEX TO TRANSACTIONS After a delay of many months, which is very much regretted, but which, it is hoped, will be one means of insuring a volume of accuracy where accuracy is very important, the Institute now has for distribution copies of the index of Volumes XXXVI to LV, inclusive. This is more than a mere index off names of authors and titles of papers. Every important topic under consideration by author or discusser is introduced under such key-word as will enable an engineer to locate the desired information with the minimum expenditure of time. This index sells for $5* in half morocco binding and $4*. in paper covers. With the index of Volumes II to XXXV (which sells for $5 in half morocco and $4 in paper covers), it forms a complete index of the first fifty-five volumes of the Institute's Transactions. These collective indexes are very valuable to members of the Institute, enabling them to look up matters in their own library; if they have the volumes to which the indexes refer, they can get the information at once, and, if not, they can readily determine whether or not a visit to a nearby public library is desirable.

Jan 7, 1918

By R. F. Domagala, D. J. McPherson

Iodide zirconium was combined with calculated amounts of ZrO2 or master alloys and arc-melted. Annealing treatments were carried out at 21 temperature levels. Metallographic examination of the heat treated specimens permitted construction of the binary phase diagram from zirconium to ZrO2. Oxygen additions to zirconium raise the transformation temperature as well as the melting point. Features of the diagram include the peritectic formation of beta, the formation of alpha directly from the melt, an intermediate phase ZrOB with a' range of homogeneity, and a eutectic between alpha and Zr02. PHASE relationships in the Zr-0 system were determined in the range 0 to 66. 7 atomic pct 0 (ZrO,). Arc-melted alloys were annealed at temperature levels between 600" and 2000°C. Determination of the phase boundaries was accomplished by metallographic evaluation of specimens quenched from the various temperatures. Incipient melting techniques were used to determine solidus curves, and X-ray diffraction work was employed to study the lattice parameters of the a solid solution and the phase ZrO,. Experimental Procedures Westinghouse "Grade 1" iodide zirconium crystal bar (approximately 99.8 pct pure) was employed for the investigation. This material is substantially free of the impurity inclusions characteristic of most zirconium metal. Previous work has shown it to be the most satisfactory grade for phase diagram studies. The zirconium crystal bar, as-received, was coated with corrosion product from autoclave tests by which its grade designation is determined. The bars were sand blasted lightly, pickled for 1 min in a 20 pct HN0,-5 pct HF aqueous solution, rinsed in water and acetone, and dried. The bars were rolled to about 1/32 in. strip, cut into 10 in. lengths, and pickled again. The material was sheared to approximately Y4 in. squares, cleaned with acetone, and stored for use. Two pounds of specially prepared "chemically pure," and 100 grams of spectrographic grade ZrO, were obtained for the preparation of alloys. The "Specpure" ZrO, was obtained from Johnson, Mat-they Co.. Ltd.. and Titanium Alloy Manufacturing Div. of National Lead Co. supplied the other grade of oxide. The "chemically pure" material (henceforth referred to as C.P. ZrO,) was used for the preparation of all alloys employed in the determination of phase relationships. A limited number of alloys were prepared with the "Specpure" oxide to recheck certain phase boundaries. Analyses of the two grades of oxide are given in Table I. The C.P. ZrOI was received in powder form, not suitable for arc melting. Therefore, this material was compressed to wafers 1 in. in diameter and about Vn in. thick. These were segmented and stored for use. The "Specpure" material, in the form of small granules, was suitable for use in the as-received condition. A nonconsumable electrode arc-melting furnace was used to prepare alloys. A water-cooled copper crucible and tungsten-tipped electrode were employed. The material was placed in the crucible and rapidly melted under a protective atmosphere of helium gas by striking the arc on a tungsten stud and directing it upon the charge material. Details of operation, including drawings of this type furnace, have been published.'

Jan 1, 1955

By C. S. Land

Relative permeability functions are developed for both two- and three-phase systems with the saturation changes in the imbibition direction. An empirical relation between residual nonwetting-phase saturation after water imbibition and initial nonwetting-phase saturations is found from published data. From this empirical relation, expressions are obtained for trapped and mobile nonwetting-phase saturations which are used in connection with established theory relating relative permeability to pore-size distribution. The resulting equations yield relative permeability as a function of saturation having characteristics believed to be representative of real systems. The relative permeability of water - wet rocks for both two- and three - phase systems, with the saturation change in the imbibition direction, may be obtained by this method after properly selecting two rock properties: the residual nonwetting-phase saturation after the complete imbibition cycle, and the capillary pressure curve. INTRODUCTION Relative permeability is a function of saturation history as well as of saturation. This fact was first pointed out for two-phase flow by Geffen et al. 1 and by Osaba et a1.2 Hysteresis in the relative permeability-saturation relation also has been reported for three-phase systems.3 Since saturations may change simultaneously in two directions in a three-phase system, four possible relationships arise between relative permeability and saturation for a water-wet system. The four saturation histories of this system were given by snel14 as 11, ID, DI and DD. I and D refer to the direction of saturation change (imbibition and drainage), with the first letter of the symbol indicating the direction of change of the water phase. As used in this paper, the second letter of the symbol refers to the direction of saturation change of the gas phase, i.e., D and I indicate an increase and decrease, respectively, in gas saturation. Only a few three-phase relative permeability curves have been published. Leverett and Lewis5 published three-phase curves for unconsolidated sand, and Snell4 reported results of several English authors for both drairrage and imbibition three-phase relative permeability of unconsolidated sands. Three-phase relative permeability curves for a consolidated sand were published by Caudle et a1.3 for increasing water and gas saturations (ID). Corey et a1.6 reported drainage (DD) three-phase relative permeability for consolidated sands. Recently, Donaldson and Dean7 and Sarem8 calculated three-phase relative permeability curves from displacement data on consolidated sands, also for saturation changes in the drainage direction. The only published three-phase relative permeability curves for consolidated sands with saturation changes in the imbibition direction (11) are those of Naar and Wygal.9 These curves are based on a theoretical study of the model of Wyllie and Gardner 10 as modified by Naar and Henderson.11 Interest in three-phase relative permeability has increased recently due to the introduction of new recovery methods and refinements in calculation procedures brought about by the use of large-scale digital computers. The scarcity of empirical relations for three-phase flow, and the experimental difficulty encountered in obtaining such data, have made the theoretical approach to this problem attractive. RELATIVE PERMEABILITY AS A FUNCTION OF PORE-SIZE DISTRIBUTION Purcell used pore sizes obtained from mercury-injection capillary pressure data to calculate the permeability of porous solids.12 Burdine extended the theory by developing a relative permeability-pore size distribution relation containing the correct tortuosity term.13 The works of Purcell and Burdine were combined by Corey14 into a form that has

Jan 1, 1969

By Donald M. Liddell, G. C. RIDDELL

THE cosmic ray continues to engage the attention of the physicists, and according to Millikan and Compton, experiments of the past summer indicate that these rays must come from interstellar space, but not from the stars themselves. According to press reports of the International Congress of Physicists at Rome, the view was given there that these rays have an initiating potential of over 750,000.000 volts. In the field of spectrographic investigation great strides have been made. The U. S. Naval Research Laboratories (R. F. Mehl and G. E. Doan of Lehigh) have just finished a year's work with a "radium torch" or "shadowgraphic apparatus" in the field of the X-ray, that bids fair to displace the latter to a great extent. The torch is more powerful., easier to operate and cheaper. Penetration of 10 in. of steel has been accomplished, which. is much -beyond the- -scope-, of the X-ray..

Jan 1, 1932

By R. R. Goddard

By use of the frequency response method with a radioactive tracer, it was possible to determine fluid dispersion and distribution in a natural consolidated and an unconsolidated medium. Measurements were made in a linear flow system at oleic saturations of 69 per cent in the consolidated medium, and 100 per cent in both media. Dispersion and distribution were obtained by measuring the amplitude attenuation and the phase velocity of sinusoidal waves with a dual monitor apparatus. The gamma ray emissions permitted in situ measurements at any distance along the porous samples. One result of importance was that the effective diffusivity increased as the wave length increased. As a consequence, a dispersion coefficient appropriate for the injection of large slugs might exceed the value measured by use of small slugs. Since flow models based solely on fluid velocity and an effective diffusivity coefficient imply that the diffusivity should be independent of frequency, such representations were not adequate for the data of this study. A comparison was made with a capacitance model of porous media with deadend PVs, but even this model was not completely adequate. By using attenuation and phase velocity data, fluid dispersion can be predicted without postulating a differential equation satisfied by the tracer concentration, thereby eliminating the need of a complicated model to represent dispersion. INTRODUCTION The flow of similar miscible fluids through a porous medium can be fairly adequately described by two parameters: the average fluid velocity and the effective diffusivity.1-3 It has been pointed out recently, however, that significant discrepancies exist between this representation and the experimental data.4-7 An improved agreement can be obtained by introducing additional parameters based on the concept of dead-end pores. The purpose of the present investigation was to find out whether the frequency response method could be used to measure the relevant parameters. The method was used in the following form. A stream of fluid was flowed at a constant rate through a sample of porous material and the concentration of a radioactive tracer in the fluid was varied sinusoidally at a fixed frequency. The effects of flow through a porous medium are a decrease in the amplitude of the concentration wave and an increase in the velocity of the peaks of the waves above the average velocity. Attenuation and phase veIocity of the waves were measured as a function of frequency and fluid velocity. The simple two-parameter model implies that the diffusivity should be independent of frequency. Data reported in this paper show that the diffusivity decreases as the frequency increases. Hence, as shown also by many others, the two-parameter model is not completely adequate. Coats and Smith 5 used two additional parameters in their model: the volume of the dead-end pores and the rate of mass transfer between dead-end pores and the flowing stream. Their capacitance model of a porous medium containing some stagnant fluid, to which transfer occurs by molecular diffusion, did not explain the dispersion results of either the present study or of theirs. Instead, the capacitance effect can be better described as the result of extreme velocity variations within the pores of the medium, with transfer between the velocity zones by convection. EXPERIMENTAL PREPARATION OF POROUS MEDIA Data reported here were obtained with a natural Berea sandstone, and with two packings of 20/25 mesh sand. Pertinent information about these media is listed in Table 1. The sandstone core was first sealed with a non-

Jan 1, 1967

By E. H. Edwards, J. Washburn, E. R. Parker

The mechanism of strain hardening was discussed in connection with some recent observations on the stress-induced motion of dislocation boundaries and on the simple shear deformation of zinc, cadmium, and copper crystals. THE nature of work hardening accompanying plastic deformation of metals has long been the subject of speculation. As early as 1925, Becker' suggested a thermodynamic process to explain slip based on the statistical probability for the occurrence of local glide steps. The theory that plastic glide was due to the presence of lattice defects known as dislocations was first introduced in 1934 by Taylor: and Orowan, and Polanyi.4 Taylor presented a rather complete analysis of the behavior and interaction of dislocations. He assumed a certain type of stress field to be associated with a single dislocation, and postulated that work hardening would result from plastic flow in two ways. First, dislocations following one another across a slip plane might encounter a barrier which would impede their movement, thereby gradually diminishing and eventually stopping plastic flow on that plane. The second mechanism involved the concept of dislocations traveling in opposite directions on nearby planes attracting one another to form a meta-stable lattice. The interaction of dislocations in such an array was shown to be large enough to require an increase in stress before plastic flow would continue. Kochendorfer5,6 extended the concept of work hardening involving a back stress due to an accumulation of like dislocations on a slip plane. He suggested that the formation of a new dislocation is hindered by those dislocations already present. The hardening resulting from the interaction of newly forming dislocations with bound dislocations was designated as "formative hardening," and indicated to be the only type of hardening necessarily connected with the slip process. In another detailed picture of work hardening, Mott and Nabarro7 assumed that sufficient dislocations are primarily present in the crystal as a consequence of growth irregularities (mosaic structure) to initiate slip. Work hardening resulted from the interaction of migrating dislocations with localized internal stresses produced during deformation. More recently, however, Mott8 as modified his treatment to include the generation of dislocations at Frank-Read sources and he accounts for the hardening by the formation of sessile dislocations. It has been widely accepted that metals of hexagonal structure, usually possessing only one set of glide planes, exhibit mechanical behavior markedly different from those having cubic structures. However, the differences in behavior of the two classes may be less fundamental than suggested. Rohm and Kochendorfer9 have shown that a single crystal of aluminum subjected to approximately simple shear gives the type of stress-strain curve associated with the hexagonal metals. Similar behavior has been demonstrated for gold and silver crystals by Andrade and Henderson.'" Thus when glide in cubic metals is restricted to one plane, the strain hardening characteristics closely resemble those of the hexagonal metals. It would appear, therefore, that an investigation of some of the strain hardening properties of single crystals sheared in simple glide might provide a more complete understanding of the phenomenon of work hardening. This report relates a number of recent observations made on single crystals of copper, zinc, and cadmium tested in simple shear. In addition, pertinent observations of effects accompanying stress-induced movement of dislocation boundaries are reported. Experimental Procedure and Results Details of the production and advantages of the type of single-crystal shear specimen employed for the following tests have been presented in a previous publication.n The method of testing makes

Jan 1, 1954

By George E. Roberts

THE gains of society from the state of primitive conditions in the past to the standard of living which prevails in the advanced countries today have been accomplished mainly by the increasing productive capacity of the population under the leadership and services of the engineer. Without improvements in the arts and industries the growth of population tends to place succeeding generations always at a disadvantage. In this country we have been exploiting with reckless prodigality a wealth of soil and minerals and timber that has been in preparation for thousands of years. We know that the prices of all national products have been advancing, and were on a rising scale even before the phenomenal increases resulting from the war. Over against this depletion of natural wealth we have the influence of improvements made in the methods of production and distribution-and the accumulation of wealth in the form of productive equipment. The net result of these opposing influences determines whether society moves forward or backward.

Jan 1, 1926

Edward Keller, Baltimore, Md. (communication to the Secretary): When, at the New Pork meeting, February, 1899, Mr. Douglas gave an abstract of his highly interesting paper on the Copper Queen mine, he invited the members of the Institute, in his usual progressive spirit, to make a full scientific investigation of the region of that mine during the prospective excursion to Bisbee, Arizona. I volunteered to examine some of the metallurgical processes and products of the works, and obtained from Mr. Douglas a valuable series of samples. Upon the issue of his paper, however, I found that he had already a considerable volume of analyses of those products, and that little was left for me to do in that respect, except to duplicate his results, the importance of which work would not have been commensurate to the time and labor involved. I selected, therefore, only some points which he had not made entirely clear, or concerning which I was skeptical. The details of most of my work will appear in a future paper. From Mr. Douglas's figures I have calculated the values for the elimination of impurities in the so-called Leghorn converter, introduced by him at the Copper Queen works, and have found them to be as follows: Percentage of Elimination of Impurities in Pour Blows of a Converter. No of ' Selenium Sulph'r Iron. Zinc. I Nickel. Lead. Antimony Arsenic. and Blow- ! Tellurium .. 1.......... 99.4 99.6 88.0 92.6 94.4 81.6 83.8 40.3 2.......... 99.0 99.6 98.1 92.5 96.8 71.9 76.6 38.1 3.......... 98.8 99.5 93.5 91.4 96.3 63.8 80.6 25.3 4.......... 99.8 99.5 95.8 95.8 97.5 65.3 76.9 36.3 Average 99.2 99.6 93.8 93.1 . 96.2 70.6 ! 79.5 35.0

Jan 1, 1900

By Ralph E. Esarey, Robert G. Reno

DriLLing activity and prospecting for oil and gas increascd in Indiana in 1941 over the previous year. The greater part of the drilling and development continued to centralize in the Indiana portion of the Interior Coal Basin, in the southwestern part of the state, but other parts of the state were not neglected. Many wildcat wells were drilled, including a series of core tests through the mantle of drift on the southern flank of the Michigan Basin. These core tests have been followed by several unsuccessful production tests. Production tests were made also along the axis of the Logansport-Kankakec branch of the Cincinnati Arch. In all, 411 field locations and 141 wildcat wells were completed in Indiana during 1941; that is, a total of 552 wells, an increase of 3 2 wells over the previous year. The field tests resulted in 260 oil wells, 57 gas wells, and 94 dry holes; wildcats included 16 oil wells, 3 gas wells and 122 dry holes. At the end of the year, 53 field wells and 34 wildcats were drilling. Gibson and Posey Counties led the state, with 154 and 155 wells drilled, respectively. However, 125 wells produced oil in Gibson County, while 98 produced oil in Posey County. Twenty-five per cent of all wells drilled were wildcat; II per cent of these produced oil and 5 per cent produced gas. Grifin field continued to lead in drilling activity, with 157 successful wells and 20 dry holes (including important wells defining the field). Production is found in five pay zones (Tar Springs, Waltersburg, Elwren, Aux Vases and McClosky). It produced a major part of Indiana's estimated 7,200,000 bbl. of oil during the year. Heusler field, Posey County, expanded with 11 oil ells and 4 dry holes in the Waltersburg and Tar Springs. Vienna field, Posey County, completed four oil producers in the Mansfield sandstone, between 1200 and 1250 ft. The College field, discovered late in 1940, received three oil producers and two dry holes in the Aux Vases. Two new fields were discovered in Posey County during the year: Lamott pool, in the Tar Springs, at 1950 ft., had initial production of 55 bbl. on discovery. One producer and one dry hole have been drilled since. Mt. Vernon pool found saturation in both the Waltersburg and Cypress formations. The discovery well tested about 1000 bbl. per day; it tested the McClosky at 2764 ft. Seven producers have been drilled since the October discovery. Welborne-Switch pool found oil in the Cypress sand at approximately 2500 ft., with an initial production of 33 bbl. One more well in the area proved a dry hole. Gibson County had the following discoveries in 1941: The Patoka field was opened by a McClosky producer of 300 bbl. Another producing well has been drilled. An attempt was made to extend the Illinois Mt. Carmel field into Gibson County, Ind., and one producer of 24 bbl, was completed on the Indiana side. A dry hole has since been drilled, one location south. One small well was completed in the Mans. field at 1105 ft. in sec. 31, T.2 S., R.12 W., Gibson County promising a new field

Jan 1, 1942

By Robert G. Reno, Ralph E. Esarey

DriLLing activity and prospecting for oil and gas increascd in Indiana in 1941 over the previous year. The greater part of the drilling and development continued to centralize in the Indiana portion of the Interior Coal Basin, in the southwestern part of the state, but other parts of the state were not neglected. Many wildcat wells were drilled, including a series of core tests through the mantle of drift on the southern flank of the Michigan Basin. These core tests have been followed by several unsuccessful production tests. Production tests were made also along the axis of the Logansport-Kankakec branch of the Cincinnati Arch. In all, 411 field locations and 141 wildcat wells were completed in Indiana during 1941; that is, a total of 552 wells, an increase of 3 2 wells over the previous year. The field tests resulted in 260 oil wells, 57 gas wells, and 94 dry holes; wildcats included 16 oil wells, 3 gas wells and 122 dry holes. At the end of the year, 53 field wells and 34 wildcats were drilling. Gibson and Posey Counties led the state, with 154 and 155 wells drilled, respectively. However, 125 wells produced oil in Gibson County, while 98 produced oil in Posey County. Twenty-five per cent of all wells drilled were wildcat; II per cent of these produced oil and 5 per cent produced gas. Grifin field continued to lead in drilling activity, with 157 successful wells and 20 dry holes (including important wells defining the field). Production is found in five pay zones (Tar Springs, Waltersburg, Elwren, Aux Vases and McClosky). It produced a major part of Indiana's estimated 7,200,000 bbl. of oil during the year. Heusler field, Posey County, expanded with 11 oil ells and 4 dry holes in the Waltersburg and Tar Springs. Vienna field, Posey County, completed four oil producers in the Mansfield sandstone, between 1200 and 1250 ft. The College field, discovered late in 1940, received three oil producers and two dry holes in the Aux Vases. Two new fields were discovered in Posey County during the year: Lamott pool, in the Tar Springs, at 1950 ft., had initial production of 55 bbl. on discovery. One producer and one dry hole have been drilled since. Mt. Vernon pool found saturation in both the Waltersburg and Cypress formations. The discovery well tested about 1000 bbl. per day; it tested the McClosky at 2764 ft. Seven producers have been drilled since the October discovery. Welborne-Switch pool found oil in the Cypress sand at approximately 2500 ft., with an initial production of 33 bbl. One more well in the area proved a dry hole. Gibson County had the following discoveries in 1941: The Patoka field was opened by a McClosky producer of 300 bbl. Another producing well has been drilled. An attempt was made to extend the Illinois Mt. Carmel field into Gibson County, Ind., and one producer of 24 bbl, was completed on the Indiana side. A dry hole has since been drilled, one location south. One small well was completed in the Mans. field at 1105 ft. in sec. 31, T.2 S., R.12 W., Gibson County promising a new field

Jan 1, 1942

By R. W. Olson, A. L. Benham

Viscous fingering was studied as it occurred in an open Hele-Shaw model (1 ft x 4 ft x 1/16 in.); it was also studied in the same model packed with 80-mesh glass beads during miscible displacements under unfavorable viscosity ratio conditions. It was determined that the lengths of 20 elements of the front were distributed normally around the average position of the combined elements under all conditions. Represented by the normal distribution, the length of the viscous fingers grew linearly with the distance traveled from the point of finger formation, increased with displacement velocity, and increased with increasing mobility ratio. Results obtained during the first few inches of displacement were of little or no use in predicting finger growth and/or finger length throughout the 4-ft model since the point of finger initiation cannot be predicted and would often occur several inches from the point of injection with either positive or apparent negative coordinates. The fingering occurring during a miscible slug displacement was much greater than would be predicted based upon the actual mobility ratios between in-place fluid and slug and between slug and following fluid, using the results described above for miscible displacement in the absence of a slug. Many of the experiments in the packed model showed that the rate of growth of the viscous fingers was diminishing toward the end of the displacement in the 4-ft long model, indicating that microscopic mixing, such as diffusion or dispersion, was decreasing the viscous fingering effect. INTRODUCTION Viscous fingering is a manifestation of a finger-shaped interface between displaced and displacing fluids occurring during typical miscible displacement projects for oil recovery. Its cause may be traced to the instability of a viscous fluid being displaced by a more mobile fluid. Viscous fingering takes on important significance in the miscible slug process 1.2 where it may be a dominant factor in determining minimum slug size. Experimental1-3 and theoretical4-7 studies of viscous fingering have been made by other investi- gators. However, an exhaustive study of the variables affecting viscous fingering had not been made. The present study was undertaken in an effort to determine the effects of some of the more obvious variables—such as mobility ratio, displacement velocity, distance displaced, and packing—upon viscous finger length and growth in a small laboratory model. It does not necessarily follow that conclusions reached by studying the results of this model study may be applied to the field. Future studies would have to evaluate the effect of model size on extension of these results. EQUIPMENT AND EXPERIMENTAL PROCEDURES A flow diagram for the equipment used in this study is shown in Fig. 1. Basically, it consisted of (1) a constant-rate pump for the injection of displacing fluid into (2) a model made up of two flat transparent plates spaced a small distance apart and (3) provisions for the production of fluid into a calibrated graduate. The displacing fluid contained a dye which allowed visual observation of finger spacing and length. The pump performed at rates from 2.5 cc/hr to 480 cc/hr, while pumping a light mineral oil into a bladder in a closed glass container holding the displacing fluid. The model was made up of two plates of 1-in. Plexiglass with dimensions 1-ft wide by 4-ft long. These were spaced 1/16 in. apart so that the internal model dimensions were 1-ft wide x 4-ft long x 1/16

By A. A. Bauer, H. A. Saller, F. A. Rough, J. R. Doig

among uranium alloy systems are the U-Zr, U-Ti,and U-Mo binary systems, in that an intermediate phase, of limited solubility range, exists in each system. These intermediate phase alloys offer a promising field of investigation, both as binary alloys and as ternary alloy combinations. While a limited amount of work has been done on the binary alloys, none has been done on ternary combinations of these alloys. As a possible prelude to more intensive investigation of these systems, a study of the phase relationships between the 6 phases of the U-Zr and U-Ti systems was undertaken. The solid-state portions of the binary constitutional diagrams for the U-Ti,1 Zr-Ti,2 and U-Zr3 systems are shown in Fig. 1. The solid to liquid transformations are not shown, as these transformations were not studied in the ternary system. The phase designations employed are based upon those shown in the uranium constitutional diagrams. The crystal structures of the various phases are given in Table I. Experimental Materials and Methods The ternary section presented is based upon the results of thermal, metallographic, and X-ray analyses of a series of alloys ranging in composition between the phases of the U-Zr and U-Ti systems (U-74 atomic pct Zr to U-35 atomic pct Ti). After preparation of the alloys, thermal data were obtained. On the basis of these data, specimens were heat treated and examined metallographically. Specimens were then selected from those heat treated for X-ray determination of the phases present in what were considered critical phase regions. Alloy and Specimen Preparation—Alloys for this investigation were prepared from selected as-reduced uranium and crystal-bar zirconium and titanium. For nominal compositions, see Table 11. Charges were arc melted from five to seven times under a helium atmosphere, finally being cast into wire-bar form for fabrication. A zirconium getter button was used to clean the furnace atmosphere prior to melting. The alloys were homogenized 20 hr at 900 °C and furnace cooled. A portion of each bar was then removed for thermal analysis; the remainder was saved for fabrication. Alloys 8 through 14 were placed in steel tubes along with zirconium getter chips and, after flushing with argon, the tubes were welded shut and rolled at 1500 °F to a 50 pct reduction in diam. The remaining alloys were annealed 24 hr at ll00°F to insure transformation of the ? phase to the 8-U2Ti phase and were then hot rolled from a salt bath. Attempts to roll alloys 6 and 7 at 1100 °F were unsuccessful. Following this, attempts were made to roll pieces of alloys 1 through 5, which had cracked rather severely during casting, at 1200 °F, but these efforts were also unsuccessful. These alloys were, therefore, further treated in their cast and homogenized condition. All alloys were pickled to remove oxide formed during rolling. Thermal data were obtained on these alloys by conventional differential thermal analysis at a heating rate of 30C per min, and by a high-speed heating method at rates of approximately 10°C per sec. For the latter method of analysis, a 36-gage Chromel-Alumel thermocouple is spot welded between two slivers of alloy, the sandwich being en-

Jan 1, 1958

By A. R. Calawa, T. C. Harman, M. Finn, P. Youtz

A study has been made of the growing, annealing, and diffusion parameters in PbSe, Pb1-ySnySe, and Pb1-xSnxTe. Single crystals of these materials have been grown using the Bridgman technique. For all of the above materials the as-grown crystals are p type with high carrier densities. To reduce the carrier concentration and increase the carrier mobility, the samples are annealed either isothermally or by a two-zone method. From isothermal anneals, the liquidus-solidus boundary on the metal-rich side of the stoichiometric composition has been obtained for some alloys of Pb1-xSnxTe and on both the metal- and seleniunz-rich sides for PbSe and alloys of Pbl-ySnySe. In Pbo.935 Sno.065 Se carrier concentrations as low as 5 x1016 Cm-3 and mobilities as high as 44,000 sq cm v-1 sec-1 at 77°K have been obtained. Inter diffusion parameters mere also studied. The ddiffusion experiments mere identical to the isothermal or two-zone annealing experiments except that the samples were removed prior to complete equilibration. The resulting p-n junction depths were determined by sectioning and thermal probing. Inter diffusion coefficients for various temperatures were calculated for both PbSe and Pb0.93Sn0.0,Se. RECENTLY, there has been considerable interest in the PbTe-SnTe and PbSe-SnSe alloys with the rock salt crystal structure. The unusual feature of these systems is the variation of energy gap EG with composition. Several investigations1-3 have shown that EG for the lead chalcogenides decreases as the tin content increases, goes through zero, and then increases again with further increase in tin content. The possibility of obtaining an arbitrary energy gap by selecting the composition is an especially attractive feature of these alloys for applications involving long-wavelength infrared detectors and lasers. In addition, some unusual magneto-optical, galvanomagnetic, and thermomag-netic effects should occur for alloys with low band gaps. If uncompensated low carrier density crystals can be obtained, then a small carrier effective mass, a large dielectric constant, and the resultant high carrier mobility should yield enormous effects at low temperature in a magnetic field. The relative variation of the energy gap with pressure should also be very large for these low gap materials. The primary purpose of this paper is to provide some information concerning the preparation of low carrier concentra- tion, high carrier mobility, and homogeneous single crystals with a predetermined alloy composition. I) DETERMINATION OF ALLOY COMPOSITIONS In all of the work described in this paper, the composition of lead and tin chalcogenides in the alloys was determined by electron microprobe analysis. Separate X-ray spectrometers are used to make simultaneous intensity measurements of the Pb La1 and Sn La1 lines emitted by the sample under excitation by a beam of 25 kev electrons focused to a spot about 2 µm in diam. These intensities are compared to the intensities of the same lines emitted by standards under the same conditions. The standards used are the terminal compounds of each pseudobinary system, i.e., PbTe and SnTe for Pbl-xSnxTe alloys, PbSe and SnSe for Pbl-ySnySe alloys. The composition of the sample is then obtained from theoretical calibration curves which relate the weight fractions of lead and tin in the alloy to the measured ratios of X-ray intensities for the sample and the standards. The lead and tin calibration curves for each alloy system were calculated by using corrections for backscattered electrons,4 ionization,5 and absorption,6 and assuming that the atom fraction of tellurium or selenium in the sample and standards is exactly +. Results obtained by using the microprobe are in good agreement with those obtained by wet chemical analysis. II) CRYSTAL GROWTH FROM THE VAPOR Early work on the vapor growth of PbSe was carried out by Prior.7 He used small chips of Bridgman-grown single crystals as the source material and frequently converted the whole charge of a few grams into one crystal. In the present work, vapor growth occurred using a metal-rich or chalcogenide-rich two-phased alloy powder as the source material. Small, nearly stoichiometric crystals are formed on the walls of the quartz tube. The procedure will now be described in detail. Initially, a 100-g charge containing (metal)o.51(chalco-genide)o 49 proportions or (metal)o.49(chalcogenide)o. 51 proportions of the as-received elements in chunk form are placed in a fused silica ampoule. After the ampoule is loaded, it is evacuated with a diffusion pump and sealed. The sealed ampoule is placed in the center of a vertical resistance furnace. The region containing the ampoule is heated to about 50°C above the liquidus temper-ature for the particular composition used. After about one-half hour at temperature, the elements are reacted and the molten material homogenized. The ampoule is quenched in water. The quenched ingot is crushed to a coarse powder for vapor growth experiments and to a fine powder for the isothermal annealing experiments which are discussed in a later section. Vapor growth experiments were carried out using the powdered, metal-rich or chalcogenide-rich alloys

Jan 1, 1969