Search Documents

By H. W. Rogers

The first steam shovels used in this country were built by the Otis Company, of Boston, about 50 years ago, but as they were of very crude construction and rather unsuccessful only a few were built. For possibly 10 years prior to 1884 successful steam shovels were made and used on certain classes of work, but it was not until that time that they were manufactured in quantities and began to play an important part in all classes of excavation. From that time up to the present day there have been gradual but continuous improvements on the original shovel, not only in the mechanical construction, but also in the design of boilers and engines which are best adapted to this class of service. In proposing a change from steam to electric operation we have to deal with a steam equipment which has not only proved its worth but has probably reached its highest stage of development and efficiency. That the electric shovel is a possibility cannot be denied, as at present from 12 to 18 shovels are in operation in this country. These shovels may be divided into three classes: the friction electric, which is operated by a single constant-speed motor with friction clutches; the three or four motor direct-current equipment, and the three or four motor alternating-current equipment. It is the second and third classes that I wish to deal with, as the first class does not compare favorably with the steam shovel so far as speed is concerned, although it may be operated as cheaply. There is probably no other class of machinery that presents a duty cycle as severe as that of the shovel, which is very short, varying from 7 to 12 sec. on the hoist, from 7 to 12 sec. on the thrust, and from 10 to 18 sec. on the swing, making a complete cycle in from 17 to 30 sec., and the motor to meet these requirements must have a sufficiently low armature inertia to permit of rapid acceleration and quick reversals under small power. It should also be a motor of rugged design, as it must be subjected to severe overloads and shocks and frequent reversals. This is especially true of the hoist motors and, to a lesser degree, of the swing motor; the thrust motor being practically stalled during the digging operation, although it may revolve or overhaul, according to conditions, and is operated at full speed only after the hoisting operation is completed.

Jan 1, 1915

By Stewart, J. B.

THE property at which this work was done consists of a large deposit of potash salts occurring in massive beds of rock salt, overlain by 600 ft. of salt-impregnated shales and marls. It is in the Province of Cataluiia, Spain, about 45 miles from the railway station of Mauresa and about a mile south of Suria. In addition to sinking the shaft, the program of construction work laid out by the European owners (not Spaniards) included a single-track narrow-gage railroad from Mauresa to the mine; one large office building and several large shop buildings, all of brick and concrete with steel truss roofs; two extensive benches for the future recovery plant; and a large village of stone dwellings for employees. The pay-roll showed approximately 1200 to 1500 men employed. After two years' operation, ending early in the autumn of 1920, the shaft had been sunk 325 ft. and still had an equal distance to go to reach the potash; all tunnels for the railroad were done and the road-bed $0 per cent completed; only a little more than the foundations were completed for all the large buildings, and the excavations of the benches were about 75 per cent done-while only a fair start had been made upon the employees' village. This was the state of affairs when the European owners decided to offer this property under a one-year option to an American syndicate, providing that they agreed to carry on the entire building program and to sink the shaft as fast as was consistent with the quality of work which they demanded, for they wished the shaft to endure at least 200 years.

Jan 1, 1926

By G. P. Marino

The "conductivity ", Kr, of a spherical void in a linear temperature gradient due to radiation is calculated by integration of the general expression for diffuse radiation between two gray surfaces of arbitrary orientation. The spherical geometry allows an exact evaluation of the phenomenon without resorting to up-proximate expressions for the radiant heat flux. The resulting expression for Kr is three quarters of the approximate value obtained by Loeb. IN the determination of the thermal conductivity of porous materials such as sintered UO2 and ThO2 fuel pellets, the magnitude of the thermal conductivity in the pores due to radiative heat transfer across the pore, Kr, may be important in assessing the total conductivity of the pellets. Loeb' has calculated Kr for various pore geometries by approximating the net flux of heat between two surfaces of temperature difference AT as 4eT~AT and obtained: K,=4yoet3odp [1] where a is the Stefan-Boltzmann constant, E is the emissivity of the radiating surface, To is the average absolute temperature of the region across which radiation occurs, dp is the largest dimension of the gap in the direction of heat flow, and y is a geometric factor. That is: y = 1 for laminar pores and cylindrical pores with axes parallel to the heat flow direction, y = 2/3 for spherical pores, y = /4 for cylindrical pores with axes perpendicular to heat flow direction. It was the purpose of this work to obtain an exact expression for K, in spherical pores by integration of the general expression for the net heat transfer between two incremental areas on the surface of a spherical pore. This procedure yields a value of Kr 3/4 of that obtained by Loeb. I) CALCULATION OF Kr Fig. 1 illustrates the general geometry which defines the problem. The total emissive power for a gray body is given by: E = EoT4 [2] where E is the radiated energy per unit area of the radiation surface per unit time, T is the absolute temperature, o is the Stefan-Boltzmann constant (o = 5.67 X lo- '' watt per sq cm-"K1), and E is the emissivity of the surface. Although Eq. [2] gives the exact expression for the total emissive power of any gray body, all practical problems involve the net exchange of thermal radiation between a body and surrounding bodies. The two major considerations in the solution of such problems are a) shape and relative position of the surfaces and b) the emissivities of the surfaces. In this work it shall be assumed that all incremental areas on a pore have the same emissivity and, further, that little or no reflection occurs (i.e., the radiation hitting a surface is either absorbed or transmitted). Thus, the solution of the stated problem requires only that consideration a be satisfied. Consider two incremental surface areas dA 1 and dA2 of the same material in a general orientation to one another. Let dAl be at temperature TI and dAz be at T2. Fig. 2 illustrates the geometrical parameters involved. That is, 71, is the normal of dA, n2 the normal of dA2, r the line connecting the centers of each area, 81 the angle between nl and r, and Q2 the angle between 7,2 and r. Using Eq. [2] and the Lambert cosine law of diffuse radiation it is easily shown that:293 WdAf- dA, = ecr T*------^fpi------" dAidA2 [ 3a 1 and

Jan 1, 1970

By Richard W. Brummett, Robert L. Dubms

Located some 180 miles east of Los Angeles in Riverside County, California, the Eagle Mountain mine supplies iron ore concentrates for the Kaiser Steel Corporation steel plant in Fontana, California, and for export to Japan. Although the deposits were first discovered in the early 1890's, no production was realized from the area until 1948 when Kaiser Steel Corporation commenced operations. A part of the large Basin and Range province, the Eagle Mountain area's geologic column comprises a thick series of metasediments resting on Precambrian gneisses and schists that have been intruded by sill-like masses of porphyritic quartz monzonite. The metasediments are composed of three quartzite units that are separated by a schistose meta-arkose and by two ore zones. They have been folded into a large east-west trending anticlinal structure that extends completely across the Eagle Mountains. The iron ore deposits occur in two well-defined horizons in the metasedimentary series, and they are found only along the north limb of the major anticline. Host rocks for the ore zones were a series of limestones and dolomites with associated quartzites. Magnetite plus pyrite comprised the primary mineralization that formed many replacement lenses and stringers of ore within the ore zones. The primary ore has been oxidized to hematite and goethite in a broad zone at higher elevations in the deposits. Hydrothermal alteration formed actinolite- tremolite granofels, local phlogopite, and minor tourmaline in the ore zones. This alteration and the ore deposition seem related to the same magmatic event that formed the porphyritic quartz monzonite intrusion

Jan 1, 1968

By S. G. Lasky

EVENTS during and since the war indicate that the nations of the world are trying to initiate an era of international co-operation. Definitions and objectives include social, economic, and human considerations no less than political considerations. The mineral resources of the world and the absolute and relative position of each nation enter into this situation. The possible use of armed might, the application of sanctions, the international flow of commerce, the ways in which this flow may encourage or hamper international well-being, and the influence of international and domestic well-being upon one another are all matters that must take mineral resources into account. If the United States is to act wisely and forthrightly in such matters we must be thoroughly informed as to our position with respect to mineral resources. What is the mineral position of the United States? A variety of widely conflicting opinions are held in authoritative and intelligent quarters: (1) For practical purposes our mineral resources are already exhausted.

Jan 1, 1946

By P. N. Richards, M. K. Ormay

The present Paper extends the previous work on cold reduced, low carbon steels to preferred orientations developed after various heat treatments. In recrystal-lized rimmed steel, cube-on-comer orientations increased with cold reductions up to 80 pct. Above that {111}<112> and a partial fiber texture with (1,6,11) in the rolling direction dominated. During grain growth, cube-on-corner orientations have been observed to grow at the expense of {210}<00l>. In re-crystallized Si-Fe (111) (112) and cube-on-edge type orientations are dominant near the surface and the (1,6,11) texture near the midplane for reductions up to 60 pct. With larger reductions {111)}<112> and the (1,6,11) texture are dominant. In cross rolled capped steel a relationship of 30 deg rotation was observed between the (100)[011] of the rolling texture and the main orientations after re crystallization. Most orientations present in recrystallized specimens can be related to components of the rolling texture by one of the following rotations: a) 25 to 35 deg about a (110) b) 55 deg about a (110) C) 30 deg about a (Ill) THE orientation texture of recrystallized steel is of interest where the product is to be deep drawn, because preferred orientation is related to anisotropy of mechanical properties such as the plastic strain ratio (r value);1,2 and in electrical steel applications where a high concentration of [loo] directions in the plane of the sheet improves the magnetic properties of the material. It is interesting to note that both these aims are to a large extent achieved commercially, even though the orientation texture of cold rolled steel does not show large variation3 and the recrystallized orientations are generally given as being related to the as rolled orientations mostly by 25 to 35 deg rotations about common (110) directions.4-6 There is, as yet, no single completely accepted theory on recrystallization. The three mechanisms that have been investigated and discussed are: a) Oriented growth b) Oriented nucleation c) Oriented nucleation, selective growth Largely from the observations of the recrystalliza-tion process by means of the electron microscope,7-11 there is now considerable evidence that the "nucleus" of the recrystallized grain is produced by the coalescence of a few subgrains to form a larger composite subgrain, which finally grows by high angle boundary migration into the deformed matrix. From the intensive work on the recrystallization of rolled single crystals of iron, Fe-A1 and Fe-Si al-loys4-" he following observations have been made: 1) The change in orientation during primary recrys-tallization can usually be described as a rotation of 25 to 36 deg about one of the (110) directions. 2) The (110) axes of rotation often coincide with poles of active (110) slip planes. 3) If several orientations are present in the cold rolled structure, the (110) axis of rotation will preferably be a (110) direction that is common to two or more of the orientations. 4) With larger amounts of cold reduction (70 pct or more) departure from these observations became more frequent. 5) After larger cold reductions, rotations on re-crystallization about (111) and (100) directions have been observed. K. Detert12 infers that a rotation relationship of 55 deg about (110) directions is also possible, by stating that the recrystallized orientation {111}<112> can form from the orientation {100}<011> of cold reduced partial fiber texture A.3 The observation by Michalak and schoone13 that (lll)[l10] formed during recrys-tallization in fully killed steel containing (111)[112],— as well as (001)[ 110] which is related to the {111}<011> by a 55 deg rotation about <110>-implies a possible 30 deg rotation relationship about the common [Ill]. Heyer, McCabe, and Elias14 have recrystallized rimmed steel after various amounts of cold reduction, by a rapid and by a slow heating cycle and found that the preferred orientations strengthened with increased cold reduction. The most pronounced orientation up to about 70 pct cold reduction was found to be {1 11}< 110>, after 80 pct cold reduction both {111}<110> and {111}<112>, after 85 and 90 pct cold reduction, {111}<112>, and after 97.5 pct cold reduction it was {111}<112> and (100)(012). In the present work, the orientation textures of the recrystallized specimens are examined under various conditions of steel composition, amount and method of cold reduction, and method of recrystallization. The relationships between the preferred orientations of the as rolled and recrystallized specimens, and the conditions for the formation of the various orientations during recrystallization are investigated.

Jan 1, 1970

By E. A. Lawrence

The experiences of Canex Placer Ltd. in establishing vegetation on a lead-zinc tailing pond are presented, hoping others with similar challenges will be benefited. History The tailing ponds are the result of 23 years of mining and milling operations, which ceased in August 1970. Roughly 7.9 million tons of lead-zinc ore were removed in that time. The ponds are located between Salmo River and B.C. Highway 3, about 8 miles north of Nelway near the Canada-U.S. border.

Jan 1, 1975

By S. A. Lever, R. Hultgren

The solidus is usually the least satisfactorily determined portion of a phase diagram. Cooling curves, which succeed well with the liquidus, show the solidus inaccurately or not at all because of segregation which occurs during freezing. Heating curves of carefully homogenized alloys might be expected to indicate accurately the solidus, but they are seldom used. Dynamic methods involving heating or cooling are never completely satisfactory because of uncertainty as to whether equilibrium is attained. A static method in which the specimen may be allowed hours, days, or even weeks to attain equilibrium is to be preferred. In a static method a solid solution, for example, is first made thoroughly homogeneous, then heated to successively higher temperatures. After sufficient time at each temperature to assure equilibrium, some property is measured which should alter strikingly when melting begins. Microscopic examination can be used to detect the beginning of melting, but the method is tedious since the specimen must be quenched, sectioned, polished, and etched before each examination. Of all the physical properties which change on melting, electrical resistance is probably the most satisfactory to measure. The measurement may be made while the specimen is at temperature without damage to the specimen. It may be repeated indefinitely to ascertain when equilibrium has been achieved. Measurements may be made on a single specimen over the whole range of temperature. Most metals approximately double their resistance on melting. Since an accuracy of a few tenths of a percent is easy to achieve, the method is highly sensitive to the beginning of melting. In spite of these advantages, which have been perceived for a long time,l,2 a reasonable search of the literature has failed to reveal a single case in which the method has been satisfactorily applied in practice to the determination of solidus temperatures. The use of electrical resistance measurements appears to have been confined in practice to changes in the solid state. In the work described in the following pages we have applied the electrical resistance method to the solidus of the lead-tin system. We have found the method to be convenient, reproducible, and highly sensitive. We chose the lead-tin system because it leads to few technical difficulties. Furthermore, a number of determinations of solidus have been made in this system by various methods and results could be checked against them. However, all published results are not in good agreement with one another, so this work should help in determining the solidus more precisely. The Lead-tin Diagram Because of its commercial importance, there have been numerous investigations of the lead-tin diagram. The results of the most recent work on the solidus are indicated in Fig 7, as well as the results of the present work. The works of Honda and Abe3 and of Stockdale4 agree fairly well with each other and with the present work. Jeffery&apos;s5 data indicate the solidus to be about 50°C lower. Honda and Abe3 used differential thermal analysis on both heating and cooling cycles. Stockdale4 used the microscopic method and also differential heating curves. Stockdale&apos;s results were about 4" higher than those of Honda and Abe at low tin contents and lower at higher tin contents. These results also agree with those of Rosen-hain and Tucker.= Jeffery5 used electrical resistance measurements of the alloy as it was being heated or cooled. Apparently he did not attain equilibrium as his results are about 40°C lower than those of Stockdale4 or Honda and Abe.3 MATERIALS AND METHODS The lead and tin used were of high purity. They were supplied by the American Smelting and Refining Co., who gave the following analyses: Lead: silver, 0.0016 oz per ton; copper, 0.0008 pct; cadmium, 0.0007 pct; zinc, 0.0002 pct; arsenic, 0.0003 pct; antimony, 0.0002 pct; bismuth, 0.0005 pct; tin, 0.0001 pct; iron, 0.0020 pct; lead (by difference), 99.995 pct. Tin: antimony, 0.037 pct; arsenic, 0.020 pct; bismuth, 0.004 pct; cadmium, trace; copper, 0.025 pct; iron, 0.004 pct; lead, 0.020 pct; nickel and cobalt, 0.005 pct; silver, 0.0005 pct; sulphur, 0.005 pct; tin (by .-difference). 99.88 pct. One hundred grams of metal with the desired proportions of lead and tin was weighed out to the nearest one-tenth of a milligram. The mixture was placed in a silica crucible, covered with charcoal, and melted in a reducing atmosphere in a gas-fired furnace. The alloy was well stirred. Chemical analysis of two of the alloys checked closely with the weighed portions. The compositions of the remainder of the alloys were taken directly from the weighings, without chemical analysis.

Jan 1, 1950

By Alfred Weiss

Over the past 25 years hard-rock mining companies have developed a number of profitable computer applications which appear applicable to operations in the coal industry. The evolution of these applications are described and the most profitable discussed. The basic nature of these systems is that they must cut across organizational boundaries. While technological advances contributed significantly to the successful implementation of computers within mining, the human aspects related to organization, management and control of systems projects remain as key to future success in coal as they were and still are in hard-rock mining.

Jan 1, 1983

By B. K. Larkin, H. R. Bailey

One of the most complicated and potentially one of the most promising secondary recovery methods is that of underground combustion. A number of field tests1,2,3 have been performed recently, apparently indicating that the underground combustion process is technically feasible. Relatively little has been published concerning laboratory or theoretical investigations of the underground combustion process. A few results of laboratory tube runs have been published4,5 and these data are valuable in understanding the process. The tube run data also emphasize the complexity of the thermal recovery process. Under various conditions, problems in heat transfer, multiphase fluid flow and combustion rates arise. For example, at low temperatures the combustion process proceeds so slowly that the front cannot be propagated. It is a problem in heat transfer to predict what injection rate of air is necessary to sustain combustion in a particular reservoir. Certain fluid flow aspects of underground combustion have been studied by Wilson, et a13. In the development of some of the flow equations, assumptions of adiabatic combustion were made. Vogel and Krueger1 have devised an analog model of the heat conduction process for a constant temperature cylindrical source moving radially outward in a homogeneous conducting medium. Jenkins and Ramey7, in a discussion of the Vogel and Krueger paper, present an analytical solution of a heat conduction problem related to problems considered by Vogel and Krueger. In the present paper an idealized model of the heat conduction problem is considered, which is more general than the model of Vogel and Krueger or Jenkins and Ramey. In particular, initial well heating, vertical heat losses and arbitrary frontal velocities are included. Equations for the temperature are obtained in terms of integrals. These integrals have been evaluated numerically for the case of frontal movement corresponding to a constant air injection rate and the case of constant frontal velocity. These results are presented graphically. From these graphs one may estimate conditions under which nearly adiabatic temperatures are obtained. The application of these results requires some knowledge of reservoir thermal properties, combustion rates and residual fuel content. Assuming no vertical losses it is possible to obtain explicit evaluations of these integrals in the linear con- stant velocity case and in the radial case corresponding to a constant air injection rate. PRESENTATION OF RESULTS The geometry of the radial system is illustrated in Fig. 1 where the reservoir is represented as a slab of thickness h. By making an energy balance for an infinitesimal volume, one obtains the following equation. T= x T+F(z.r).........(1) where F (z,r) =HWv1/pc (r-r1), if z h/2 = 0, if z >h/2 . In Eq. 1, V- represents the Laplacian operator and 8 is the Dirac delta function. Eq. 1 is the well-known diff-sion equation with a source term and may be applied to a linear system. For example, if the source is moving in the direction of the x axis, then the argument of the delta function is x - 1,. In deriving Eq. 1 the following approximations were made concerning the actual combustion process: (1) all heat transfer is by conduction in a homogeneous medium, (2) the formations bounding the reservoir have the same thermal properties as the reservoir, (3) the combustion fuel is consumed instantaneously as the front arrives, (4) there is a constant fuel concentration

By W. Philippoff, Donald E. Cadwell, S. R. B. Cooke

THE importance of contact angles in flotation has long been recognized, but little has been done to get quantitative relationships between the surface coverage of the mineral by the reagent, the length of the hydrocarbon chain, and the contact angle. It is well known that for a complete monolayer on the surface of a mineral the contact angle 8 is determined only by the reagent1 and principally by the chain length of the hydrocarbon radical. Although for flotation the monolayer usually is regarded as being complete, early experiments of Wark and Cox&apos; showed that at very small concentrations of potassium ethyl xanthate the contact angle on galena changed in a continuous way from 0&apos; to the equilibrium value of 60". Further, Gaudin and Vincenta showed a similar continuity using heptylic acid and sphalerite. This shows that with probably incomplete monolayers, 0 varies with the degree of surface coverage. At the time these experiments were made it was impossible to measure the actual amount of surface coverage, especially since the decrease of the collector concentration in the liquor could be influenced by chemical side reactions. Through the use of the radioactive tracer method for the measurement of the amount of collector adsorbed on the surface of the mineral, Gaudin and Bloecher&apos; were able to determine accurately the actual surface coverage of dodecylamine acetate on quartz, but they did not measure any contact angles. It is believed that the relationship between the surface coverage and the contact angle is extremely important in flotation, especially as Gaudin and Bloecher showed that a 95 pct recovery is possible with a coverage of only 5 pct. Theoretical Considerations The work of adhesion W is the energy bound (in ergs per sq cm) when an interface is formed. It is determined by the difference of the free surface energies (surface tensions) of the respective phases 7j and yZ before contact and the interfacial free surface energy y, after contact. The definition of the contact angle permits the elimination of the unknown surface energy of the solid and hence the calculation of W from the surface tension of the liquid y and the contact angle 8: W = y (1 + COS0) [1] Consider a surface consisting of two components, identified as 2 and 3, 1 being the liquid. The amount of 2 in the composite surface is x, where 0 < x < 1. The respective contact angles with 1 and air are 8, and 8.. The total work of adhesion of such a surface is the sum of the values of the components multiplied by their respective areas. A formal relation can be written: Wm = x-W2+ (l-x)-W, [2] in which W, is the work of adhesion of the composite surface. Eq 1 can be introduced into Wt and Wa, but in the case of W, some discussion is needed. If the two components are segregated, each component forming an integral part of the composite surface there is no physical meaning for a contact angle 8m calculated from W,, by using eq 1. If, on the other hand, the area of each patch of the components is small in comparison with, say, the diameter of the bubble used in measuring, it could be expected that 0m would have a physical significance, because of the action of the surface tension of the liquid-gas interface tending to smooth out sharp corners. How small these patches would have to be is difficult to predict, but by using composite surfaces with microscopically

Jan 1, 1953

By S. R. B. Cooke, W. Philippoff, Donald E. Cadwell

THE importance of contact angles in flotation has long been recognized, but little has been done to get quantitative relationships between the surface coverage of the mineral by the reagent, the length of the hydrocarbon chain, and the contact angle. It is well known that for a complete monolayer on the surface of a mineral the contact angle 8 is determined only by the reagent1 and principally by the chain length of the hydrocarbon radical. Although for flotation the monolayer usually is regarded as being complete, early experiments of Wark and Cox&apos; showed that at very small concentrations of potassium ethyl xanthate the contact angle on galena changed in a continuous way from 0&apos; to the equilibrium value of 60". Further, Gaudin and Vincenta showed a similar continuity using heptylic acid and sphalerite. This shows that with probably incomplete monolayers, 0 varies with the degree of surface coverage. At the time these experiments were made it was impossible to measure the actual amount of surface coverage, especially since the decrease of the collector concentration in the liquor could be influenced by chemical side reactions. Through the use of the radioactive tracer method for the measurement of the amount of collector adsorbed on the surface of the mineral, Gaudin and Bloecher&apos; were able to determine accurately the actual surface coverage of dodecylamine acetate on quartz, but they did not measure any contact angles. It is believed that the relationship between the surface coverage and the contact angle is extremely important in flotation, especially as Gaudin and Bloecher showed that a 95 pct recovery is possible with a coverage of only 5 pct. Theoretical Considerations The work of adhesion W is the energy bound (in ergs per sq cm) when an interface is formed. It is determined by the difference of the free surface energies (surface tensions) of the respective phases 7j and yZ before contact and the interfacial free surface energy y, after contact. The definition of the contact angle permits the elimination of the unknown surface energy of the solid and hence the calculation of W from the surface tension of the liquid y and the contact angle 8: W = y (1 + COS0) [1] Consider a surface consisting of two components, identified as 2 and 3, 1 being the liquid. The amount of 2 in the composite surface is x, where 0 < x < 1. The respective contact angles with 1 and air are 8, and 8.. The total work of adhesion of such a surface is the sum of the values of the components multiplied by their respective areas. A formal relation can be written: Wm = x-W2+ (l-x)-W, [2] in which W, is the work of adhesion of the composite surface. Eq 1 can be introduced into Wt and Wa, but in the case of W, some discussion is needed. If the two components are segregated, each component forming an integral part of the composite surface there is no physical meaning for a contact angle 8m calculated from W,, by using eq 1. If, on the other hand, the area of each patch of the components is small in comparison with, say, the diameter of the bubble used in measuring, it could be expected that 0m would have a physical significance, because of the action of the surface tension of the liquid-gas interface tending to smooth out sharp corners. How small these patches would have to be is difficult to predict, but by using composite surfaces with microscopically

Jan 1, 1953

By B. C. Allen

Grain boundary grooving has been studied in chromium, molybdenum, and tungsten under a variety of conditions using high vacuum techniques and tantalum -gettered argon. The average surface free energy of solid chromium, and the chromium-liquid silver interface free energy were respectively found to be 2200 ± 250 and 500 i 130 ergs per sq cm from groove formation kinetics and estimates of pertinent volume difffusion coefficients. The results for chromium were unffected by variations in interstitial content ranging from 0.003 to 0.09 pct C, or 0.003 to 0.03 pct O. Surface diffusion is the primary mechanism of groove formation in chromium under 1 atm argon at 1200" to 140O°C, and is essentially unaffected by 0.003 to 0.09 pct C, 0.003 to 0.03 pct O , metastable nitrogen contents up to -0.01 pct, and up to 2 torr Ag vapor. At higher temperatures, the major mechanism is volume diffusion in argon or evaporation-condensation in stutic vacuum. Surface diffusion occurs in molybdenum at 0.5 to 0.96 and in tungsten at 0.5 to 0.9 of the absolute melting tempera -ture by a single mechanism, possibly by the migration of single adatoms or vacancies. Results were slightly affected by up to 23 tory Sn vapor, and in molybdenum were essentially unaffected by 0.5 Ti or carbon in the range 0.002 to 0.02 pct. Volume difffusion through the liquid is the mechanism of groove formation in chromium-liquid silver at 1200" to 1400°C and in molybdenum-, Mo-0.5Ti-, and tungsten-liquid tin at 1200" to 2000°C. The solid-liquid interface free energies involved were estimated from grooving kanetics. WHEN a grain boundary intersects a solid surface, a groove tends to form along the line of intersection at temperatures above about half the absolute melting point (0.5 TM). The groove progressively grows by preferential atomic migration either by diffusion or evaporation. Establishment of a groove angle occurs in accordance with the grain boundary and surface free energies involved. The motivation for groove formation is a reduction in the total surface free energy of the system. This study is a continuation of previous work on thermal grooving of chromium, molybdenum, and tungsten.&apos; The temperature ranges were extended, and the effect of metallic and interstitial impurities was evaluated. The results were such that certain interface free energies and surface self-diffusion coefficients were deduced from the grooving kinetics. EXPERIMENTAL WORK Materials and Preparation. As indicated in Table I, the 0.05-0.08-cm-thick chromium, molybdenum, and tungsten sheet used was nominally 99.99 pct after recrystallization. Two lots of molybdenum with about the same analysis, Mo-0.5Ti,* and tungsten were ob- *Alloy compsitions are expressed in weight percent . tained commercially. Extruded chromium rod,&apos; prepared from iodide process crystals, was warm rolled to sheet at 700°C. Sheet of three Cr-0 impurity alloys containing up to 0.03 pct 0 was prepared by warm rolling arc melted, extruded, and swaged rod. Two Cr-C impurity alloys containing up to 0.09 pct C were made by equilibrating unalloyed chromium with a known amount of CH4 for 24 hr at 1150°C in previously evacuated quartz capsules. Chromium containing nominally 0.015 and 0.06 pct N was similarly prepared by equilibration with NH3. The sheet was recrystallized to give a stable grain size about equal to the sheet thickness. Molybdenum and Mo-O.5Ti were recrystallized in a tantalum resistance furnace 1 hr at 1 x lo-5 torr at 2300" and 220O°C, respectively. Tungsten was similarly annealed for 1 hr at 2500°C. Chromium and its impurity alloys were outgassed at 1100°C and recrystallized 1 hr at 1700°C under 1 atm Ar. Except for nitrogen, the impurity content stayed roughly constant. Nitrogen in both alloys was reduced to <0.001 pct. In fact, over 80 pct of the added nitrogen was lost after outgassing at llOO°C and annealing sheet 1 hr at 1300°C in argon in the presence of tantalum. Such a rapid loss can be rationalized since -2 torr N are required for equilibrium with 0.04 pct N in solution,3 while the equilibrium pressure is ~10-5 torr over tantalum at 1300°C.4 The recrystallized sheet was cut into small coupons which were metallographically ground and polished on one side with a minimum of grain boundary relief. The surface roughness was on the order of 0.01 µ. The tin and silver used were nominally 99.999 spec-trographically pure. After being outgassed at 1100°C and equilibrated in a molybdenum crucible for 0.5 hr at 1800°C in argon, the tin contained 3 ppm 0, <0.3 ppm N, and 0.1 ppm H. Following outgassing at 900°C and equilibration in a chromium crucible 1 hr at 1400°C in argon, the gas content of the silver was 1 ppm O, <0.5 ppm N, and 0.3 ppm H. Grooving Under Argon or Vacuum. All specimens were placed in unsealed containers made from rod or sheet of the same alloy, thereby enabling the polished surface to achieve gas-solid equilibrium. The annealing fixtures are shown in Fig. 1. The specimen was placed in a resistance furnace with a tantalum or Ta-10W heating element plus tantalum fixtures or radiation shields. Chromium was outgassed at 1100°C, and molybdenum and tungsten were outgassed at 1900°C to 1 x l0-5 torr or at the grooving temperature, whichever was lower. In vacuum anneals, the specimen was then heated directly to the intended grooving temperature. In argon anneals, 99.996 Ar was admitted

Jan 1, 1970

By William R. Chedsey

IN the last two years the E.C.P.D. committees having to do with the inspection of engineering schools for possible accrediting have been concerned with the engineering content of some of the mineral industries courses. Originally the discussion arose with regard to engineering geology, or geological engineering, afterward broadening to metallurgical engineering, ceramic engineering, agricultural engineering, and other branches not pertinent to this discussion. Some members of visiting committees took the attitude that they probably would have to accredit these types of training as included in the engineering group if they met the average standard set by the mining schools, though they questioned -whether they were really engineering.

Jan 1, 1939

By J. V. Gluck, Ping-Wang Chiang

The tellurium-rich region of the Sb-TI-Te ternary system was investigated by means of DTA, metallo-graphic, X-ray, and electron beam microprobe techniques on the sections Sb2Te3-T12Te3, SbTlTe2-Te, SbT1Te2-Sb2Te3, and SbTlTe2-T12Te3. The phase behavior of this region is summarized in terms of four ternary invariant reactions and a schematic reaction diagram is suggested. Isopleths for the sections SbT1Te2-Sb2Te3, Sb2Te,-T12Te3, and SbTlTe2-Te were constructed, and a schematic diagram of the projections of the liquidus lines and invariant planes is presented. No evidence was found to support the existence of the ternary compound "SbTlTe3", or pseudo-binary behavior of the section T12Te3-Sb2Te3, as reported by Borisova and Efremova. Electrical conductivity, Seebeck coefficient, and thermal conductivity measurements were made at room temperature on fully annealed samples. 1 HE phase relationships in chalcogenides are often complex and difficult to resolve, particularly since the approach to equilibrium is a rather slow process. For example, the phase diagram of the T1-Te binary system was in doubt until clarified by Rabenau et al.,1 the phase fields at compositions near Bi2Te3 in the Bi-Te binary system have only recently been satisfactorily elucidated by Glatz,2 and there may still be some question as to the extent of the Sb2Te3 field in the Sb-Te system.3-5 In ternary systems, the existence of the compound "AgFeTe2" was the subject of a number of conflicting reports6-8 and the stoichiometry of the composition "AgSbTe2" was in doubt for a period of time.9 Recently, questions have arisen regarding the existence of certain compounds in the ternary systems Bi-Tl-Te10-14 and Sb-Tl-Te.15 The impetus for studies of these latter systems stemmed from the report of Borisova et a1.10 of a congruently melting ternary compound, "BiTlTe3", which apparently had extremely favorable thermoelectric properties for room-temperature cooling applications. Attempts by other investigators to produce the compound or confirm the transport properties proved to be unsuccessful.12-14 Recently, Chiang and Gluck14 reported studies of the phase relations in the tellurium-rich region of the Bi-T1-Te system which indicated that the section T12Te3-Bi2Te3 was not pseudobinary as suggested by Borisova et a1.10 The contention of Spitzer and sykes12 was supported that the composition "BiT1Te3" was multiphase, with the primary constituent actually being BiTlTe2, a compound whose existence has been well demonstrated.16,17 The investigation reported in the present paper was prompted by a later report of Borisova and Efremova15 on a similar study of the section T12Te3-Sb2Te3 from the Sb-T1-Te system. They also claimed this section to be pseudobinary, and that a ternary compound "SbTlTe," was formed peritectically. Some "preliminary" crystallographic data were given for the compound and thermoelectric transport properties were presented. In view of the questions concerning the behavior of the Bi-T1-Te system and the existence of the compound "BiT1Te3" it was suspected that the Sb-T1-Te system might behave in a similar fashion, particularly in light of the known existence of a compound SbT1Te2, iso-structural with BiT1Te2.17 Consequently, an investigation was undertaken to clarify the phase relationships in the tellurium-rich region of the Sb-T1-Te system. It is the purpose of this paper to present the results of this study, including a representation of the phase relations, isopleths for various composition sections, and the determination of some phase compositions and transport properties. EXPERIMENTAL PROCEDURES Commercially available high-purity (99.999+ pct) elements, purchased from the American Smelting and Refining Co., were used for the sample preparation. All samples were made from thoroughly mixed powders of previously prepared master alloys: SbTlTe2, Te, Sb2Te3, and T12Te3. Stoichiometric quantities of the constituents for each 10-g sample were weighed into a specially cleaned fused silica tube and sealed under a vacuum of better than 5 x 10-5 torr. The sealed constituents were fused and reacted at 650° to 750°C for at least 4 hr under continuous agitation in a "rocking" furnace, and the resulting product was air-cooled. The tube was opened and the sample was ground to a powder. A portion of the powder was rebottled in a DTA tube under vacuum, and the rest of the material was similarly resealed in a separate tube, re-fused in the rocking furnace, and again cooled to make the ingots for electrical and microstructural studies. All samples were subjected to further heat treatments as discussed in the section on experimental results. Each DTA tube was made of 7-mm-OD fused silica tubing with a concentric 2-mm-ID depression about 4 mm long formed in the bottom to accommodate a thermocouple. The size of a DTA sample was 0.5 to 1.0 g. An Aminco Thermoanalyzer whose accuracy was within 2°C18 was used for the DTA measurements. The metallographic samples were prepared by conventional techniques. A solution of FeCL dissolved in a methanol-HC1 mixture was found to be the most satisfactory etchant. Electron beam microprobe scanning and point-count examinations were made on polished and unetched samples using an ARL Electron Microprobe at an electron beam voltage of 20 kv. The detectors were set to receive characteristic La1 radiation. Calibration standards of the pure elements were incorporated in each sample mount; quantitative point counts were calibrated by a method similar to Ziebold

Jan 1, 1969

By Colin M. Sargent

THE electron diffraction pattern as seen in the electron microscope represents an approximately plane section of the reciprocal lattice. Identifying the zone axis of a diffraction pattern is often laborious for a crystal of low symmetry, especially if several crystal orientations are present. A program has been written in FORTRAN II (Version 2) for the IBM 1620 which will assist in plotting out reciprocal lattice sections. The calculation is performed by choosing a zone axis [uvw] and determining the d spacings and angle between the planes (Ow - v) and (wO - u). (This procedure is varied slightly for zone axes with Miller indices equal to zero.) Cartesian coordinates for the reciprocal lattice points are then calculated for these planes and for (ww— [u + v]). Any reciprocal lattice points within the parallelogram formed by the origin and these three points are then computed. The input and output are best described by use of an example (Monoclinic ZrO2) used in the author&apos;s work. Input consists of two cards: 1) The crystal parameters: a, b, c, a, 8, y, e.g., 5.1477, 5.2030, 5.3156, 90.000, 99.380, 90.000. 2) Three numbers, D, E, F, e.g., 5, 3, 3.0710-the first is the limit of the sum (u + v + w) considered; the second limits the absolute value of u, v, and w to (E- 1), e.g., 2, so that zones (221) would be the highest order considered in this example; the third, F, is the required constant, yL. Output is in the format shown in Table I. The reciprocal lattice sections may then be plotted on standard graph paper and compared with the unknown diffraction pattern. (Note that no attempt has been made to deal with systematically absent reflections.) A card deck for the program is available from Colin M. Sargent, ARZ, W-PAFB, Dayton, Ohio, 45433.

Jan 1, 1969

By Otto H. Henry, Edward L. Badwick

Up to the present time, according to Hansen1 and Haughton,2 the constitution of the bismuth-indium system has not yet been published. The generally accepted value for the melting point of indium, as listed in most scientific journals and textbooks, is 155°C. Recently, however, H. M. Davis3 has determined a new melting point for indium of 257.3°C ± 0.1°C. Since bismuth has been used in preponderance as an alloying element in the majority of low-melting alloys, and indium has been used with considerable success in lowering the melting points of low-melting alloys,4,5 an interest has been developed in the application of these two metals, making a complete knowledge of the constitution of its alloys desirable. In this investigation, the melting point of indium reported by H. M. Davis has been found to be substantially correct. A value of 157.2°C ± 0.5°C was determined. The two eutectic compositions have been placed at 34 and 50 pct bismuth with their respective eutectic temperatures as 72.4&apos;C ± 0.5°C and 90°C ± 0.5°C. The bismuth-indium phase diagram has been determined by thermal and microscopic analysis and is shown in Fig I. THERMAL ANALYSIS Granulated bismuth and indium shot, having a guaranteed purity of 99.99 and 99.95 pct, respectively, were melted in a carbon crucible by means of a laboratory heater. To minimize oxidation of the alloys, a heavy mineral oil (Nujol) having a high flash point was used. A platinum-platinum rhodium thermocouple 0f fine wire encased in a thin-walled Pyrex glass tube, about 1/8 in. in diameter, was connected to a type K potentiometer for temperature measurements. The thermo-couple was calibrated against the melting points of tin, bismuth, and the silver-copper eutectic and the boiling point of water. Since the temperature readings could be reproduced to 0.2°C, and the accuracy of the temperature standards in this range is slightly better than 0.5°C, it seems reasonable to assume that the temperature readings are reliable to approximately 0.5°C. The cooling rate could be controlled by varying the amount of insulation surrounding the crucible. Three or four layers of asbestos paper, 1/16r, in. thick, sufficed to give a cooling rate of from 1° to 2°C per minute. Undercooling was slightly noticeable. This condition was minimized by vigorous stirring, since the advantage of using slower rates was too small to justify the greater expenditure

Jan 1, 1947

By John V. Beall

HEAVY-DENSITY separation processes, a commercial application of the sink-float test used in mineralogical laboratories for the separation of mineral particles by their difference in specific gravity, are the biggest development in mineral dressing since flotation, which was at about the same stage of development thirty years ago. The scope of their application has broadened and, though still in the development stage, they are being accepted in a constantly increasing number of commercial installations. This progress in mineral beneficiation is especially satisfying when we realize that our high-grade ore deposits are fast disappearing and a big factor in determining whether a hole in the ground is being sat upon by a liar or an honest citizen is how economically the ore dressers can concentrate comparatively low-grade ores. As early as the middle of the nineteenth century attempts were made to use aqueous salt solutions in a heavy-liquid separation for cleaning coal. But the original and recovery costs of these liquids were high and further, the fact that they were corrosive, unstable, and toxic added to the difficulty in using them.

Jan 1, 1948

By David L. Holt, Walter A. Backofen, Anwar-ul Karirn

ANNEALING the binary alloy, Mg-0.5 wt pct Zr in a hydrogen atmosphere results in extensive precipitation of zirconium hydride. The morphology of these precipitates has already been investigated.lm3 Squires, Weiner, and phillips4 found, following creep testing of the hydrided alloy at 450" and 500°C, that hydride denuded zones formed along grain boundaries that were aligned approximately normal to the tensile axis. Zone formation was attributed to diffusional creep by magnesium transport down the prevailing stress gradients.4&apos;5 Recently, electron microprobe analysis by Karim, Holt, and Backofen6 showed the zones indeed to be zirconium-free and furthermore it was shown that in compression, zones formed along boundaries approximately parallel to the stress axis. Thus it was confirmed that the zones are formed by diffusional creep. Typical zone-formation is shown in Fig. 1. Karim, Holt, and Backofen also measured the con- tribution to the total strain, from diffusional flow, slip creep, and grain boundary shear: results showed that diffusional strain tends to saturate with increasing imposed strain, while grain boundary shear eventually becomes the dominant deformation mode. It was suggested in explanation that the precipitate-denuded zones are soft and easily sheared, such deformation contributing to the grain boundary shear measurement. A point to be emphasized is that the Mg-0.5 Zr alloy was not superplastic for the index of strain rate sensitivity of flow stress, m = a log log 6 was only 0.25. It was recognized that diffusional creep in a poly crystalline aggregate must be accompanied by boundary shearing.&apos; The suggestion was that the non Newtonian-viscous character of diffusional creep in the Mg-0.5 wt pct Zr alloy is due to resistance to sliding of boundaries lying approximately parallel to the tensile axis.= The work described in the present note should be seen against the above background for it represents initial efforts to observe in a similar way diffusional creep in a superplastic alloy. Previous work with the ternary-alloy Mg-6 Zn-0.5 Zr, pellet extruded, showed it to be superplastic however it does not contain resolvable precipitates to act as internal markers for diffusional creep. Also the fine grain size of the alloy (0.5 p) made conventional metallography rather difficult. Solubility relationships in the Mg-Zn-Zr system are not well known, however making reasonable guesses about the probable phase diagram of the ternary, Mg-Zn-Zr, various heat treatments were attempted to produce hydride precipitation. Finally a 16-hr anneal at 495&apos; in hydrogen was found to pro-

Jan 1, 1970

By C. W. Allen, B. D. Cullity

The proportional limit of iron crystals in torsion is governed by the resolved shear stress in the most highly stressed slip systems, averaged around the specimen circumference, and does not obey a critical resolved shear stress law. Crystals of most orientations exhibit a stage of easy plastic deformation, akin to easy glide in tensile or shear specimens. Transient deformation, similar to that which occurs in single crystals of other materials, is also observed. THE torsional deformation of single crystals of magnesium (hcp) and aluminum (fcc) has been described recently by Choi et al.,&apos; especially with respect to the criterion for the orientation dependence of the onset of plastic flow in these materials. The purpose of this paper is to present results of torsion tests of iron single crystals and thus to extend this yield criterion to a bcc metal. In addition to considering the variation of proportional limit with crystal orientation, this paper also briefly treats work hardening, transient deformation, and the mechanism of plastic flow in iron. The effects of the method of surface polishing and the chemical purity of the iron have been investigated. STRESS DISTRIBUTION It is convenient to express the stress at any point of a cylindrical crystal stressed in torsion in terms of t0, which is the shear stress acting at the surface on a plane normal to the axis of the cylinder and in a direction tangential to the cylinder. This stress is given by To = 2T/pr3 [1] where T is the applied torque and r the specimen radius. The shear stress t, resolved in any chosen slip system is given in terms of 7, by1 Ts/TO = sin 0, cos d sin (0, -) + cos , sin d sin d - ) [2] where 0 and d are the angles between the specimen axis and the slip plane normal and slip direction, respectively; h is the angular circumferential position on the specimen at which t, is being determined, measured from an arbitrary reference plane which includes the axis;o and d are the angular coordinates of the projections of the slip plane normal and slip direction on a transverse section with respect to this same reference plane. Slip in iron occurs in a <1ll> direction on the {ll0}, (1121, and (123) planes, which together comprise 48 slip systems. A complete evaluation of the stress distribution in an iron crystal stressed in torsion would therefore require a calculation of Ts/T0 as a function of for 48 different slip systems. Fortunately Gough,&apos;who studied the behavior of iron crystals in alternating torsion, was able to simplify this problem considerably. He showed that it was sufficient to consider a kind of average slip plane for each slip direction, namely the mathematical plane of maximum resolved shear stress containing the slip direction considered. This simplifying approximation is possible because, for each slip direction, the active slip plane or planes lie very near this mathematical plane of maximum shear stress. Vogel and rick&apos; have critically reviewed the early work of Taylor and Elam,13 Taylor,14 and Fahrenhorst and schmid8 from which the identification of the above crystallographic planes as slip planes in the bcc lattice largely stems. While their criticism is clearly justified, their own results do little to clarify the issue. The role of cross slip (screw dislocations changing glide planes) is evidently so important in this case, as Read3 has suggested, that methods for deducing slip systems from observations of gross slip traces are inadequate, such traces commonly arising from complex dislocation motion. Thus the treatment given here involving the plane of maximum resolved shear stress seems a logical simplification especially in view of Gough&apos;s2 study of a iron. There is, however, an assumption built into the subsequent treatment the comparative validity of which is difficult to assess, namely, that slip in all slip systems in iron may be characterized by a common critical resolved shear stress. The shear stress 7, resolved in a slip direction defined by d andd, and on the plane of maximum shear stress containing this direction, is found by first maximizing 7s/70 with respect to either Oo or 4,. The slip plane coordinates are then eliminated by using the relation between 0, ,o and d, d, namely,

Jan 1, 1963