Search Documents

By Charles E. Weaver

Discussion of the paper of CHARLES E. WEAVER, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 103, July, 1915, pp. 1419 to 1427. MILNOR ROBERT, Seattle, Wash.-A year ago at this time, 12 wells were being drilled for oil in western Washington. Some excitement attended the operations; many thousand acres of land were leased to oil companies and stock was widely advertised. The location of the wells may be described by referring to the conclusions in Dr. Weaver's paper, in which the State is divided into four areas. In the area described first, which includes the Cascade Mountains and eastern Washington, where conditions are decidedly against the existence of commercial oil fields, no new drilling was reported. In the second area, the Puget Sound Basin, where conditions are unfavorable, but to a less degree, five wells were being drilled. The third region, covering certain parts of southwestern Washington, contained four drilling wells and several others projected or beginning operations, in spite of the absence of petroleum seepages. None of the wells mentioned is fully active today. On the western side of the Olympic Peninsula, along the Pacific Ocean, are three wells which have been the scene of operations for the past two to three years. The region they are prospecting contains seepages of light oils and is the fourth area described in the paper. The difficulties of transporting both men and supplies to the well sites have delayed operations and brought the costs up to high figures. The drilling of these three wells is interesting on account of the presence of oil in nearby seepages and its occasional appearances in the material penetrated. A. C. McLAUGHLIN, San Francisco, Cal.-The most important part of Washington is on the Olympic Peninsula. The geological conditions on the Peninsula are not similar to the conditions in California, and it would not prove to be a continuous belt of oil-bearing territory from there to here if oil should be found at either end.

Jan 12, 1915

By L. L. Wyman

THE resultant embrittlement caused by the exposure of oxygen-bearing copper when hot and exposed to reducing gases has been the subject of many studies.1 Little attention, however, has been given to the possible embrittling effects due to atmospheres or conditions that under some circumstances might be the source of a reducing gas. At rather infrequent intervals there occur reports of copper becoming embrittled during normal annealing cycles in commercial steam-atmos-hered furnaces such as customarily are used for this operation. As might be expected, several other factors exist-such as oil, dirt on the wire, or in the furnace, or metallic surface contacts that might produce reducing gases and be the source of the trouble. However, in consider-ation of the statement made by Ruder,2 it would seem that under some conditions steam itself might prove to be the source of trouble. A consideration of the amount of the dissociation of water vapor up to temperatures of the melting point of copper shows that' the amount of hydrogen that could come from this source is far too minute to account for any embrittlement. What such information does not tell is what will happen at the surface of copper when subjected to steam at elevated temperatures, for entirely different conditions may persist, which would account for Ruder's observation. Furthermore, there are no data as to what might happen at the surfaces of other materials present, the result-ant of which might affect the condition of the copper present. For this reason, it was decided to make a series of experiments com-parable to those previously conducted by the writer,1 which would clarify the effect of the steam on copper, and in copper in the presence of steel.

Jan 1, 1940

By J. L. Sepulveda, R. F. Yap, R. Jauregui

INTRODUCTION The Third Theory of Comminution, oftentimes called the Bond Theory, was first published by Fred C. Bond in 1952. Since then, it has been widely used in the milling industry to size crushing and grinding equipment as well as to predict and evaluate their performance. Although two other comminution theories were advanced almost a century earlier, one by Rittinger, 1867, and the other by Kick, 1885, their use was limited because they did not agree with actual commercial comminution systems (Bond, 1961). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced in particle breakage, and equals the work represented by the product minus that represented by the feed. For particles of similar shape, the crack tip length is equivalent to the square root of one-half the surface area, and the new crack length is proportional to [(1/vT - vF)]; where P and F are particles diameter of product and feed, respectively. For practical calculations, the particle diameter can be expressed in terms of the 80% passing sizes, P and F, respectively. Therefore, the work input is given by, [10 _ 10', W = Wi [7P_7F(1)] Where W = the energy input to the mill, (kwh/t) Wi = Work Index, (kwh/t) P = square sieve opening which 80% of the product passes, (microns) F = square sieve opening which 80% of the feed passes, (microns) Equation (1) is the mathematical statement of the Third Theory, or the Bond equation. Numerically, the work index is the energy required in kwh/t to reduce a given material from theoretically infinite feed size to 80% passing 100 microns. The work index of a particular material is determined in the laboratory by conducting the standard Bond grindability test. Bond developed separate tests for the rod mill and the ball mill. The simplified test method described in this paper, which is used at Anaconda Research Center to approximate the work index, is an alternative procedure to the ball mill

Jan 1, 1982

By Malcolm C. Bridges, Ian A. Goddard

INTRODUCTION Mount Isa mine is a major producer of both copper and lead-zinc- silver ores. During the 1975/76 year, 4.3 million tonnes of copper ore were extracted at an average grade of 3.4%, and 2.4 million tonnes of lead-zinc-silver ore at average grades of 7.0%, 6.7% and 173 grams per tonnes respectively. Systematic lead-zinc mining has continued for just over 45 years and copper mining for just over 30 years. Virtually all mining is underground. The composite and somewhat schematic longitudinal section of Figure 1 shows the overall distribution of ore at the Mount Isa mine. The mine can be roughly divided into two parts about a central shaft complex: to the north there is predominantly lead-zinc ore and to the south there is copper ore. Underground operations are serviced by three shafts in the central shaft complex (P61, R62 andU62) and another to the south in the copper mining area (X41). Mining is spread over a total strike length of 2.9 km and extends to a depth of 960 m. Currently, lead-zinc ore is being extracted between 15 and 11 levels and is hauled to the central ore-hoisting shaft on 13 and 15 levels. Copper ore is being extracted between19 and 13 levels and is hauled to the central shafts on 19 level. The principal lead-zinc mining methods used now, as they have been over the last ten years, are sublevel open stoping and cut-and- fill stoping, with about equal tonnages of ore from each (Figure 2). Since about 1970, there have been several interesting developments in lead-zinc mining methods and procedures, principally: • the development of an effective method for the recovery of pillars between open stopes and • the evolution of safer and more productive cut-and- fill methods. During this period also, the focus of mining has moved 120 m deeper

Jan 1, 1977

By Charles L. Mantell, James E. Hoffmann

Mechanical inclusion, electrophoretic deposition, and adsorption were studied as mechanisms for code-position of aluminas present in copper-plating electrolytes as an insoluble disperse phase. Mechanical inclusion was not a significant factor. That codeposi-tzon of aluminas by an electrophoretic mechanism was unlikely was substantiated by measurements of the potential of the aluminas. The alumina content of the deposits was studied as a function of the pH of the bath. These tests in conjunction with sedimentation studies demonstrated the absence of an isoelectric point for the alutninas over the pH range examined. Thiourea in the electrolyte (a substance known to be adsorbed on a copper cathode during electrodeposition) affected the amount of alumina in the electrodeposit. However, no adsorption of thiourea on aluminas in aqueous dispersions was detected. If it were possible to produce a dispersion-hardened alloy of copper and alumina by electrodeposition, an alloy possessing both strength and high conductivity at elevated temperatures might be anticipated. Investigation of the mechanism of codeposition of aluminas with copper was undertaken with the hope that knowledge of the mechanism would aid in the development of such an alloy. The word "codeposit" here does not necessarily imply an electrolytic phenomenon but rather that the materials codepositing, the various aluminas, are transported to and embedded in the electrodeposited copper by some means. Mechanical inclusion in electrodeposition implies a mechanism of codeposition which is wholly mechanical in nature; the only forces acting on a particle are gravity and contact forces. Such a particle is presumed to be electrically inert and incapable of any electrical interaction with electrodes in an electrolytic plating bath. Processes for matrices containing a codeposited phase by electrodeposition from a bath containing a disperse insoluble phase frequently state that code-position is caused by mechanical inclusion.10,2,12 If settling, i.e., gravity, be the controlling mechanism for codeposition of aluminas, then assumptions may be made that 1) the content of alumina in the electrodeposit should be enhanced by increasing the particle size, 2) the geometry of the system, that is, the disposition of the cathode surfaces relative to the di- rection of the falling particles, should affect the alumina content of the electrodeposit, 3) in geometrically identical systems the chemical composition of the electrolyte employed should exercise no effect on the alumina content of the deposit, that is, the alumina content should be the same in all cathode deposits irrespective of bath composition. A bent cathode19 evaluates the clarity of filter effluent in electroplating baths by comparing the roughness of the deposit on the vertical surface with that on the horizontal surface. Two difficulties are inherent in this technique: 1) the current density on the horizontal portion of the cathode would be substantially greater than that on the vertical surface; 2) should the deposit obtained be rough, projections on the vertical face could act as horizontal planes and vitiate the relationship between the vertical and horizontal surfaces. Bath composition should have no substantial effect on the alumina content of the deposit. Two different electrolytic baths were employed. They possessed variant specific conductances and substantially different pH ranges. The experimental tanks were rectangular Pyrex battery jars 6 in. wide by 3 1/4 in. long by 9 3/4 in. deep. The cathodes were stainless steel 316 sheet of 0.030 in. thickness, cut to 7.5 by 1.75 in. and bent at right angles to form an L-shaped cathode whose horizontal surfaces measured 1.75 by 3.0 in. All edges and vertical surfaces were masked with Scotch Elec-troplaters Tape No. 470. The anodes were electrolytic cathode copper 9 in. high by 2.25 in. wide by 0.5 in. thick. To eliminate inordinately high current densities on the projecting edge of the cathode, the anode was masked 1 in. above and below the projected line of intersection of the cathode with the anode. The exposed area of the anode was equal to that of the cathode, providing both with equal average current densities. The agitator in the cell was of Pyrex glass and positioned so its center line was equidistant from cathode and anode, and a plane passed horizontally through the center of the blade would be located equidistant from the bottom of the cathode and the bottom of the deposition tank. The assembled apparatus is depicted in Fig. 1. Hatched areas on anode and cathode represent the area of the electrodes wrapped with electroplaters tape. MATERIALS The chemicals were copper sulfate—CuSO4 • 5H2O— technical powder (Fisher Scientific Co.). Spectro-graphic analysis showed substantial freedom from antimony, arsenic, and iron. Traces of nickel were present.

Jan 1, 1967

By C. Goldberg, R. H. Wynne

WHEN using an optical goniometer to determine crystal orientation' it is advantageous to use a preferential etchant so that the etch pits have plane faces which are parallel to crystallographic planes, all of which are of the same "form." "Westinghouse Silver Etch" (WAg), a preferential etch for germanium, is made up as follows: 40 ml of 49.7 pct hydrofluoric acid, 20 ml of 70.7 pct nitric acid, and 40 ml of distilled water containing 2.0 g of silver nitrate. Examination of metallographs of WAg etched surfaces (Fig. 1, for example) indicates that, regardless of crystal orientation, the faces of the etch pits are (111) surfaces. Optical goniometer examination of these WAg etched surfaces also indicates that the faces of the etch pits are (111) surfaces, i.e., all bright reflections are from (111) planes. When using an optical goniometer of the type described by Barrett,' not only (111) reflections from a WAg etched germanium surface but also other reflections of lower intensity will be observed. These latter reflections can cause confusion. We have used an optical goniometer made from a war surplus astrocompass and a galvanometer lamp. The reflections are observed by using the goniometer in a darkened room and letting the reflected light be in- cident upon a piece of white paper. The resulting decrease of goniometer sensitivity enables (111) reflections only to be observed. This in turn permits the crystal orientation to be determined in a matter of minutes, since only two measurements are necessary. The authors wish to acknowledge the help received from R. E. Davis who assisted in making the metallographs and aided the authors in the interpretation of the metallographs.

Jan 1, 1954

By Cleveland Dodge

THE present organization of Copper Queen employ-ees, known as the Employees' Conference Com-mittee, is really an outgrowth of the former Grievance Committee, which, in turn, had developed from the original Hospital Committee. The relatively small membership of these older organizations, the practical limitation of their activities to the presenting of grievances, and their lack of initiating powers, were the principal defects which the plan now in operation seeks to overcome. A somewhat parallel scheme was instituted in our Sacramento Hill division about four years ago; this gradually developed into the Ways and Means Committee, which, in addition to providing a forum for the discussion of operating problems, was instrumental in establishing an excellent and mutually satisfactory bonus system. Before recommending adoption of the plan now in force, we made extensive inquiries among those who have had any experience in such matters, and ended by proposing a modification of a scheme developed by John Leitch,1 which was characterized by its similarity to the constitution of the Federal Government. As finally remodeled, the. plan was submitted to vote of the entire working forces at the Copper Queen mines, and was adopted by them in May, 1920. Mining opera-tions since that date have been so interrupted that it is scarcely possible to state exactly what the results have been. The following quotations are from a printed pamphlet containing the constitution of the organization, as finally adopted. The first extract is from a letter addressed by the management to the employees: The plan submitted for your approval and adoption is modeled after the constitution of our own country, under which every individual is given an opportunity for advancement, according to his ability and determination, and every citizen is given a voice in the laws that shall govern him. So it is to encourage the individual employee in advancement, and to give him a voice in making the rules that shall govern his conduct, that we favor the adoption of the proposed constitution.

Jan 1, 1923

By Robert Schorr

A Discussion of the Paper by Robert Schorr, read at the Atlantic City meeting, February, 1904. (Washington Meeting, May, 1905.) E. T. DUMBLE, Houston, Texas (communication to the Secretary*) :-In addition to the list of publications mentioned by Mr. Schorr and those by Prof. Hofman, I call attention to the following references : Studi sulle Lignite, by Capacci. Turin (1890). (An excellent work.) Report of Brown Coal Industry in Germany. J. Cosmo Newberry. Department of Mines, Victoria (1892). Second Report of the Royal Commission. on Coal Supply. Vol. II. London (1904). Peat Fuel: Its Manufacture and Use. Report of the Bureau of Mines of Ontario, 1903. Mr. Schorr says : " Brown coal and peat are briquetted as a rule without binder," but this statement is entirely true only so far as raw peat is concerned, and it is but partly true of brown coal. With regard to raw peat, briquetting without bond is carried on successfully both in Europe and America, and the development of the industry in Canada is fully described in the Bureau of Mines report for 1903, mentioned above. While there is still room for improvement in the efficiency of some of the arrangements for drying the peat previous to briquetting, a very satisfactory fuel is made at a price which enables it to compete with coal. During the late strike in the anthracite regions of Pennsylvania, the manufacture of peat: briquettes received a considerable impetus, and possibly the attention directed to it on this account may result in a. considerable increase in the output. In Canada. the peat when it is first excavated from the ground

Mar 1, 1905

The Tuscarora mining district, which has been highly productive of gold and silver ores in past years, is situated about 50 miles north- west of Elko, Nevada. The town of Tuscarora lies at an altitude of about 6,000 ft on the west side of the Independence Valley. Precipitation, particularly the winter snowfall, is considerably greater than in many other parts of Nevada, and temperatures are lower. From Tuscarora can be seen-across Independence Valley in the mountains to the east, a distance of about 12 miles, the Freeport Minerals Jerritt Canyon mine, which seems to be-destined to become one of the great gold mines in the western hemisphere. Tuscarora, a gold and silver camp, was active from the early 1870s to 1903 and produced about $10 million in those 30 years. Ten major mines and several smaller ones were operated in an area of about 1.45 square kilometers (one-half squaremile). The deepest shafts were only 230 m (750 ft) but most of the ore came from about the 105 m (350 ft) levels. Mineralization above the water table, at about 30 m (100 ft), was mostly native silver and cerargerite with free gold. Below the water table the ore was rich in sulfides including argentite, stephanite, proustite, pyrargyrite, enargite, arsenopyrite, bornite, chalcopyrite, pyrite, sphalerite and galena. A number of the properties contain sizeable dumps of what was con- sidered waste rock when it was mined. These dumps aggregate over 408,000 mt (450,000 st) with one dump, the Navajo, containing over one-third of the total. A few grab samples taken in the summer of 1978 from some of the dumps indicated interesting silver values with minor gold content. AgAu Exploration Ltd., was organized to explore and develop these dumps into a heap leaching operation. In the fall of 1978 a campaign was started to lease, with front money payments on a royalty basis, three groups of claims on which were located a few hundred thousand tons of dumps. In September and October of 1978, a systematic program of sampling was started on the Navajo dump which was most favorably situated in that it was near to an area which would furnish good sites for heap leaching pads. At the time it was fully recognized that sampling of dumps was a most difficult problem. Because of the topography on which they were situated and the manner in which they were formed, each dump required its own special sampling technique.

Jan 1, 1981

By W. H. Gunniss

When the copper smelters were built, in Montana, all of the refractory products which were used in their construction were shipped in from Eastern factories. It was apparent that if a material suitable for the manufacture of these products could be found within the State, a saving of freight could be effected and a new industry built up. Prospecting for such materials was started and experiments were made with samples from numerous deposits. Considerable effort and funds were expended in an attempt to manufacture silica brick from Dillon quartz, a light colored sandstone that is found near Dillon, Mont., on the Oregon Shortline railroad. As a brick material the Dillon quartz was a failure, but it has proved very satisfactory as a silica cement. It is now being used in laying silica brick and for reverberatory furnace bottoms. A bed of quartzite that is particularly suited to the manufacture of high-grade silica brick was finally discovered at Browns Spur, 6 miles west of Anaconda. The material from this deposit is now being used in the manufacture of the Anaconda silica brick, which have gained a wide reputation for heat-resisting and lasting qualities. The analysis of an average sample of this quartz is: SiO2, 96.7; Fe2O3, 0.3; Al208, 2.5; CaO, 0.3 per cent. The very low percentage of fluxing ingredients makes this a most refractory material. All of the Anaconda silica brick are hand molded. Various types of brick machines have been tried, but the hand-mold process proved the best suited to the manufacture of silica brick from this material. The silica is first put through a jaw crusher and is then dumped into wet pans, where 4 per cent. of lime paste is added, to produce a bond. Without the lime the material would not be plastic enough to mold. After a few minutes' grinding in the wet pans the material is conveyed to the molder, who forces it into the molds by hand. The brick are then dumped on pallets and placed in the drier, where they are left. until dry enough to be set in the kilns. Some of the brick are re-pressed before being dried. They are burned about five days, in round down-draft kilns. It is not necessary to have as much heat in the kilns as the brick will be subjected to when in use in the furnaces. Montana refractories are used in smelters throughout the West. Prospecting for fire clays was also carried on. After experimenting with clays from several different deposits, it was found that a mixture of

Jan 1, 1914

By C. R. King

Most of the acid volcanic glasses such as obsidian, perlite, pitchstone, pumice, and pumicite (volcanic ash) are susceptible to some expansion if suddenly subjected to a suitably high temperature in a properly designed furnace, and subsequently suddenly cooled. Expansion results from the action of chemically combined or dissolved water expanding as a vapor within the softened heated rock particles. This expansion forms countless minute bubbles within the pasty mass of the natural glass particles. If the particles are cooled before these bubbles can escape, the resulting products are cellular, more or less spherulitized glass froths or hollow glass spheres of many types. Chemically, they are essentially aluminum silicates containing about 70 to 75 pct silica, 10 to 16 pct alumina, and 2 to 7 pct sodium plus potassium oxides. They are relatively resistant to attack by acids or alkalies, are resistant to heat up to over 1000°F, and are completely inert to insect or fungus attack. These products are of great potential value in many branches of industry as insulation materials, aggregates, fillers, abrasives, and additives. By proper selection of the perlite rock type and control of processing conditions, expanded perlite of a bulk density varying from about 2 to 20 Ib per cu ft can be • made. The physical properties of the particles comprising a product of a given bulk density also may be varied within wide limits of porosity, water absorption, and crushing strength. In general, crushing strength of expanded perlite increases in direct relation to increase in bulk density, but insulating value varies in inverse ratio to bulk density. The selection of a particular grade of expanded perlite for a given use as an aggregate is therefore always a compromise between insulating value, lightness, and friability. If porosity and water absorption are factors affecting the use of the material, factors other than bulk density are important. Some types of perlite rock tend to decrepitate excessively during expansion, resulting in a highly porous or even hygroscopic product of high friability relative to the bulk density of material produced. In general, treatment of any good perlite rock below the temperature necessary for maximum expansion, or insufficient time in the hot zone of the furnace for effective heat penetration to the core of the rock particles will result in some decrepitation and high porosity in the expanded product. On the other hand, exposure of the material to the temperature required for optimum expansion for a period of time slightly longer than that necessary for proper heat absorption will result in a slightly heavier product of extremely low porosity, i. e., a glazed surface. It is beyond the scope of this paper to describe in detail the rock types and processing methods used to produce the many types of expanded perlite in present use, or that may be produced to fill the present and future needs of industry. A few phases of the economics involved in processing and selling products made from this abundant and cheap mineral raw material, plentifully distributed in large and relatively accessible deposits in most western states and in other areas within economic shipping distance of large centers of consumption, will be treated with particular reference to the Los Angeles area. Relation of Balk Density to Use and Cost of Production Perlite differs from most other lightweight aggregates and fillers in that the raw material (perlite rock) may be quarried much as rock arid sand is mined, and then shipped into consuming areas as crude rock in open gondola cars at correspondingly low freight rates and handling costs. At processing plants in or near large consuming areas the rock is converted into relatively fragile, very bulky products which in most cases are used within a short haul of the processing plant or enter into a manufactured product made at the site of the perlite processing plant.

Jan 1, 1950

The following is a report of the papers submitted to the Papers 'and Publications Committee during 1928: The Committee held nine regular meetings during the year 1928. During that period there were presented to the Institute 214 papers which were acted upon as follows: Accepted as Technical Pub1ications............................ 85 Declined for publication...................................... 16 Action pending, Dec. 31...................................... 25 Manuscripts held for annual volumes, Dec. 31................... 7 Withdrawn temporarily...................................... 1 Accepted as Preprints........................................ 20 Printed for first time in volumes.............................. 35 Published in Mining and Metallurgy........................ 12 Papers in Technical Publication No. 156 (Coal Classification) and not accounted for elsewhere in this table..................... 10 Mimeographed only*................................... 3 Total.................................................. 214 * A considerable number of papers were mimeographed for the annual meeting. Of the 85 papers accepted as Technical Publications 8 were reprinted in the Transactions, 7 in Proceedings of the Institute of Metals Division (1928), 7 in Iron and Steel Technology in 1928, 13 in Geophysical Prospecting, and 50 were in Technical Publication form on Dec. 31. Of the 20 papers accepted as Preprints 1 was reprinted in the Transactions, 13 in Petroleum Development and Technology in 1927, 2 in Geophysical Prospecting, and 4 were in Preprint form on Dec. 31. Of the 35 papers printed for the first time in the various volumes 8 were included in the Transactions, 2 in Proceedings of the Institute of Metals Division (1928), 1 in Iron and Steel Technology in 1928, and 24 in Petroleum Development and Technology in 1927. Of the 12 papers accepted for Mining and Metallurgy 1 was, accepted for Geophysical Prospecting and 1 for the Transactions. There were published in 1928 113 Technical Publications containing a total of 1928 pages, as against 88 in 1927, totaling 1528 pages. The Technical Publications published in 1928 were classified as follows: Group A, Metal Mining, 17 papers (361 pages); B, Milling and Concentration, 4 papers (39 pages); C, Iron and Steel, 15 papers (256 pages); D, Non-ferrous Metallurgy, 13 papers (191 pages); E, Institute of Metals, 36 papers (588 pages); F, Coal and Coke, 15 papers (392 pages); G, Petroleum and Gas, 10 papers (246 pages); H, Non-metallic Minerals, 3 papers (33 pages); I, Mining Geology, 18 papers (356 pages); K, Mining Administration, etc., 3 papers (47 pages); L, Geophysical Prospecting, 21 papers (430 pages).

Jan 1, 1929

By James Yancik

The Howe Coal Co. is mining the Oklahoma Lower Hartshorne bed which ranges in seam thickness from 38 to 42 in. and pitches approximately 7° to the northeast. The raw feed to the cleaning plant averages about 20% ash and 1.10% sulfur, being reduced in the cleaning process to 4.8% ash and 0.9% sulfur with a free swelling index of 8 or 8%. This coal rivals the Pocohantas seam in chemistry and coking characteristics but has better fluidity than the Pocohantas seam coal. The coal is presently being prepared for the Japanese steel market in an 85-tph pilot plant designed and constructed by Roberts & Schaefer. The cleaning-plant flowsheet is discussed in detail.

Jan 1, 1972

Planning for a surface coal mine includes selecting the best means and equipment for uncovering the coal, loading it, and transporting it to the preparation plant. The machines and methods that will ensure optimum production will depend upon the location and characteristics of the seam to be mined. Stripping Techniques The choice of stripping units is influenced primarily by the system of mining, such as contour or out-crop mining as contrasted to mining in a region of rolling terrain with relatively flat upland surfaces. Factors such as the life of the mining operations production requirements, types of overburden, local and regional dip of coal, and land reclamation are other important considerations.

Jan 10, 1967

By Augustus Locke

San Francisco Meeting, October, 1911.) Two Opposed Interpretations of the Tonopah Structure.-The important geological publications concerning the Tonopah mining-district are those of Spurr 1 and of Burgess.2 In these publications are presented fundamental differences of interpretation, which are the more interesting because both authorities have had ample opportunity for observation, and because both are geologists of proved ability. I was vastly puzzled to know which had the better of it, and in order that I might reach a conclusion in my own mind, I recently spent some time in the district going over the physical evidence. Surprising as it may seem, this evidence looks agreeably conclusive. A review of it will, I believe, be of interest to those who are familiar with the previous publications. The general geological features of Tonopah are shown in Fig. 1, and the differences of interpretation referred to are outlined in the accompanying notes. Briefly, Burgess regards the various rocks as flows, lying in the order of their deposition. Spurr regards them in part as flows, and in part as flat-lying intrusives. The disagreement, then, concerns the rocks regarded on the one hand as intrusives, and, on the other hand, as flows. These rocks are chiefly the so-called calcitic andesite, the upper rhyolite, and the lower rhyolite. Economic Importance of the Question of Interpretation.-The economic importance of the question of interpretation is, of course, limited to its bearing on the probable distribution of 1 Geology of the Tonopah Mining District, Nevada, Professional Paper No. 42, U. S. Geological Survey (1905). Report on the Geology of the Property of the Montana-Tonopah Mining Co. (1910). An abstract of this report is given in the Mining and Scientific Press, vol. cii., No. 16,p. 560 (Apr. 22, 1911). 2 The Geology of the Producing Part of the Tonopah Mining District, Economic Geology, vol. iv., No. 8, pp. 681 to 712 (Dec., 1909).

Feb 1, 1912

By Thomas A. Earl

Much of the strip mining in the Appalachian coalfields was done prior to backfilling and regrading requirements, resulting in many devastated areas which also have serious acid mine drainage problems. Economic incentive or justification for reclaiming these thousands of acres of land does not exist unless some value can be attached to the open cuts and weathered overburden piles. In Pennsylvania many of these old strip mine cuts are being successfully used for sanitary landfills and sludge disposal sites, and multiple benefits are realized. Given proper regulatory control, this technique could be beneficially applied to many other areas in the east.

Jan 1, 1977

By Charles M. Means

A thoroughly modern coal-handling system has been installed at the Pittsburgh Terminal H. H. &. Coal Co.'s new No. 8 shaft, or Cover-dale mine, about 11 mi. (17.7 km.) from Pittsburgh on a spur of the Montour R. R. The Pittsburgh scam, which is the one worked, is reached at a depth of 342 ft. (104 m.). Power is delivered to the mine at 22,000 volts over a transmission line of the bow-arrow type of construction. A private telephone line connecting the various mines and the main office in Pittsburgh is carried on the same poles. The high-tension line is brought to an outdoor, step-down, transformer substation, where three 833-kv.-a., single-phase, 60-cycle, oil-insulated, self-cooled transformers reduce the potential to 2300 volts. The transformers are protected by electrolytic, aluminum-cell lightning arresters, horn gaps, and choke coils. High and low-tension busses, together with fuses, choke coils and air-break horn-gap switches with thcir remote-control operating mechanism are mounted on a substantial structural-steel tower 25 ft. (7.6 m.) in height. Mine Substation The transformer substation is adjacent to a. pressed-brick building that houses direct-current substation equipment together with switchboards, etc., for the control and distribution of power. This building also contains the hoist for the men and supplies. Main Switchboard The 2300-volt circuit is carried underground in a conduit from the transformer substation to an oil switch in the substation and supply hoist building. This is the main switch controlling the 2300-volt busbars mounted back to a twelve-panel black-slate switchboard. From the switchboard, 2300-volt circuits are carried to transformers feeding the street and house lighting systems and to other transformers furnishing power for the elevator and lighting circuits in the store building. Other 2300-volt circuits run from this switchboard to the main hoist building, fan house and auxiliary or man-and-supply hoist. High-tension wiring,

Jan 1, 1922

By H. J. Levinstein, W. H. Robinson

A method of chemically polishing silver for metal-lographic examination has been developed. The samples are prepared by polishing on 0, 2/0, and 3/0 paper. They are then polished on 600 micro-cut paper, followed by a final mechanical polish on a cloth containing 5µ diamond paste. The samples are then chemically polished in a solution of 100 cc of saturated chromic acid and 5 cc of a 5 pct HC1 solution. The chemical polishing is performed by swabbing with a cotton ball saturated with the solution. During the chemical polishing, the sample is rinsed frequently in running water. Polishing in this manner for 5 min is sufficient to remove the strained material from the previous polishing operations. The amount of material removed is approximately 4µ/min. The surface obtained is flat and free of pits. Fig. 1 is an interference micrograph of a silver surface polished by this technique. If the solution employed is of improper HC1 content, an interference color film will form on the sample. This film can be removed either by swabbing with a cotton ball saturated with ortho-

Jan 1, 1962

By Ashok K. Sinha

During the course of an in~*estigation into the occurrence of ordered AB3 structures, the following new phases have been found —CrRh3 (AuCu3 type), CrCo3 (MgCd3 type), HfCo4 (Ths Mn23 type), and WPt, MoPh type). The composition of the TiPt3-x phase (TiNi, type) is close to Ti23Pl77. The alloy chenzistry of transition rnetal AB3 structures is rezliewed in the light of electron concentration correlations of hex-agonality recently obtained for quasi-binary alloys. The relatizte colurne contraction in the AB3 structures increases with increasing difference in volume of the conzponents. A family of ordered close-packed layered structures is formed by stacking identical layers of composition AB, in various sequences, such that the coordination is twelvefold throughout and there are no A-A contacts. Previous work' on quasi-binary AB3 alloys has led to the conclusion that the stacking sequence of the AB, structures changes with increasing radius ratio RA/RB from a purely cubic, through different mixtures of hexagonal and cubic stacking to a purely hexagonal stacking. However. for binary AB3 alloys, a correlation between the type of the crystal structure and the position of the components in the various volumns of the periodic table has been noted.2-5 It has been noted6 that this correlation appears to hold even though the radius ratio RA/RB may vary over a considerable range with the location of the components in the three long periods. Another study7" of several quasi-binary systems led to the conclusion that an increase in hexagonality of the stacking is associated with increase in the electron concentration e/a. as defined by the average per atom of the total number of electrons outside the inert gas shells. In apparent conflict with this conclusion, it is known that seven binary alloy structures isotypic with TiNi3 which is 50 pct hexagonal occur at a higher electron concentration (e/n = 8.5) than that (e/a = 8.25) for the 100 pct hexagonal MgCd3 type structure present in seven binary AB3 alloys. Table 111. In the present work, an investigation into the occurrence of binary AB3 structures in transition metal alloys was made, and a survey of binary AB3 structures is presented. EXPERIMENTAL The starting materials were pure metals of 99.9 wt pct purity. The alloys were arc-melted under partial pressure of argon and annealed in sealed silica capsules lined with molybdenum foil under argon at- mosphere. The total weight loss upon melting and subsequent annealing was always less than 1 pct and hence the alloys will be referred to by their intended (unanalyzed) compositions. Wherever the constitution permitted. the alloys were given a homogenizing treatment at 1200°C (3 days) prior to annealing. Unless otherwise stated all alloys were annealed at 900°C for 1 week and water-quenched. Sometimes the final annealing treatment was carried out on powders to accelerate the attainment of equilibrium. X-ray powder patterns were taken using a Guinier-de Wolff focusing camera (CuK, radiation) or an asymmetrical focusing camera (Co or CrK, radiation). For lattice parameter determination. internal silicon standards were employed. The intensity calculations were made using a Fortran IV program written by Jeitschko and parthe.9 RESULTS Twenty AB3 and three AB4 alloys were investigated. Table I lists the crystallographic data on some of the intermediate phases encountered in the present work. Table II contains the X-ray data for HfCo, (Th,,Mn,, type). The positional parameter, x. was assumed to be 0.378. the value for Th6Mnn2310 The X-ray pattern of ZrCo, was very similar to that of HfCo, and the previous structure determination of ZrCo, by Kuzma el al." was confirmed. Ordering in the alloy CrCo could be ascertained by the presence of only one weak super lattice line (101). the others being too weak presumably owing to the small difference in the scattering powers of chromium and cobalt. This line was observed in the X-ray pattern of powder from the massive sample annealed at 830°C (7 days) after the powder had been reannealed at 600°C (24 hr). The diffraction pattern of the powder similarly reannealed at 830°C (24 hr) contained only the lines due to a mixture of hcp and fcc Co(Crj solid solutions. Therefore, it appears reasonable to assume that O2 and/or N2 contamination which would be less likely to occur during the 600°C anneal was not responsible for the observed weak reflection. Also. this reflection cannot be identified with any of the strong lines of the neighboring s phase which is present in the Co-Cr system at higher chromium contents. The composition corresponding to the TiNi3 structure observed by Raman et al.12 in the two-phase alloy Ti,zt,, has been established in the present work as being between There was satisfactory agreement for the low-angle lines (up to d = 1.997A) between the observed diffraction pattern of TiCua and that calculated assuming the ZrAu, structure. as recently proposed by Pfeifer-et a1.I3 However. some of the superlattice lines. e.g., at d = 1.937 and 1.919A. predicted by the ZrAu, structure were not actually observed eve? though neighboring lines. at d = 1.947 and 1.986A. of comparable calculated intensity were present. The ZrAu

Jan 1, 1970

By M.A. Hunter

This paper gives the results of an investigation of the specific resistance and temperature coefficient of the electrical resistance of nickel and its important alloy, monel metal. For most of the pure metals, the temperature coefficient of resistance is approximately 0.004 per degree centigrade at 20" C. Nickel and iron, however, are exceptions. This property is important as it gives us good material for the construction of thermometers and other instruments involving electrical control. A summary of information on this subject has been publishcd by the Bureau of Standards.l The present experiments antedate this publication by several years and as the information obtained is not contained in it, the results of the experiments arc published as additional information. Electrical Properties of Pure Nickel It is generally conceded that the lowest values for electrical resistance are obtained in the purest metal. In the case of nickel, the best material obtainable is electrolytic nickel, which contains approximately 99.80 per cent. nickel, 0.15 per cent. iron, and 0.05 per cent. copper. Any cobalt that may be present is included in the nickel figure. If the elcctrolStic sheet has been deposited without intermission, it is possible to cut a section from the sheet and roll it into wire without melting. By this means a nickel wire may be obtained that is uncontaminated by any of the impurities always taken up by nickel during melting. Two samples of nickel wire obtained from different electrolytic nickels had the follolving electrical resistance and temperature coefficient of electrical resistance: Specific Temp. CofEE. Sample MateRial ReSISTance peR Deg. C. NO. 1 Electrolytic nickel.................... 7.55 0.00550 NO. 2 Electrolytic nickcl ................... 7.60 0.00553 * Rensselacr Polytechnic Institute. Director of Research, Driver-Harris Co. Russell Sage Laboratory, Rensselaer Polyt,ecllnic Institute. 1 U. S. Bureau of Standards, Circular 100 (March, 1921).

Jan 1, 1923