Search Documents

By Donald A. Corrigan, John Chipman

It is shown that the heat of solution of nitrogen in liquid-iron alloys is Proportional to the interaction coefficient. This proportionality forms the basis for a method of predicting nilrogen solubility at any temperature when the interaction coefficient is knoun at 1600°C ov when the solubility is known at some one temperature. A method for predicting the solubility of nitrogen in liquid steels, including alloy steels, was proposed some years ago by Langenberg.' Since the data available at that time were restricted to temperatures of about 1600°C, his predictions were similarly restricted. More recently, Nelssonz devised an approximate method for estimating nitrogen solubilities at higher temperatures. It is the purpose of the present paper to present a method by which the solubility of nitrogen at any temperature within the steelmaking range may be predicted from the known interaction coefficients at 1600°C. Nitrogen in iron and in all of the alloys to be considered here is known to obey Sieverts' Law; hence the activity of nitrogen in an alloy of fixed composition is proportional to its concentration, here expressed in weight percent. The activity of nitrogen is defined as equal to its weight percent in the binary Fe-N solution at any temperature. Its activity coefficient in any alloy is the comparison being made at equal values of T and PN2. In all alloys the activity coefficient changes with composition, log fN being a linear function of the percent of alloying element at low concentrations. In the following calculations the alloy compositions are restricted to those in which this linear relation is exhibited. For most systems this is a fairly wide range, for example up to 5 pct V and to 10 pct Cr or Ni. For this composition range. complex alloy is the same as that in the Fe-N-j ternary solution. Langenberg's method of prediction was based on Eq. [3], the values of log fN for various additions being taken from a graph. Instead of using the simple addition indicated in Eq. [3], he used a more complex method suggested for Fe-S-j alloys by Morris and Buehl.3 For the composition ranges in which Eq. [2] is valid the two methods are equivalent. Nelson extended the prediction to other temperatures on the assumption that logfN is inversely proportional to absolute temperature. It may be shown that inverse proportionality would result if the partial molal entropy of nitrogen were unaffected by addition of the alloy element, an assumption which Nelson designated as a "regular" solution. It has been shown recently by the authors4 that this assumption is not a good approximation. The heat of solution of nitrogen (N2) in an alloy may be obtained if the solubility is known as a function of temperature. Measurements of this nature have been reported recently by Beer5 for Fe-Mn alloys, by Nelsson2 for Fe-C, by El Tayeb and parlee6 for Fe-V, and by Pehlke and Elliott7 for many alloys embracing a wide range of compositions. In connection with the work of the last named authors it is noted that their Fig. 22 gives the heat effect per half mole rather than per mole of N2. In using their data we have shifted some of their values slightly by using the best straight line in preference to their curve. Their data, supplemented by others from the literature, are summarized in Table I. In Fig. 1 the heat of solution of nitrogen is shown as a function of composition for the several alloy systems. The difference between the heat effect in the alloy. AH; and that in pure

Jan 1, 1965

By E. C. Dominguez

INTRODUCTION The first commercial plant in the world to successfully produce pellets from manganese ore fines is the ICOMI pelletizing facility in northern Brazil. The main purpose of this paper is to describe the manganese pelletizing process that was developed through a cooperative R & D program by the Bethlehem Steel Corporation and ICOMI, i.e., Industria e Commercio de Minerios, S. A. The process combines heavy- media and gravity separation, reduction roasting, magnetic separation, and pelletizing on a straight-grate indurating machine. It produces high-grade manganese pellets from reviously unsalable low-grade ore fines at a rate of 20,000 tonnes (1) per month. The physical properties of the manganese pellets are comparable to those of iron ore pellets. The pelletizing plant, built at a cost of about 18 million dollars, is part of an ICOMI complex that includes manganese ore mining, an ore-washing plant, and railroad and port facilities, as well as two town sites. These two towns, one at the mine and the other at the port, each with complete community services, were built by ICOMI to serve the needs of over 1500 employees that operate the industrial complex. To give an idea of the magnitude of the investment represented by this complex, the cost up to 1957 to develop the mine and supporting services and social infrastructure was over 100 million dollars. It should be borne in mind that the above capital cost figures are in dollars of the years during which the respective projects were initiated and completed.

Jan 1, 1977

By S. Jana, C. M. Wayman

The reverse transformation of bcc martensite to the fcc phase was studied in an Fe-33.95 wl pct Ni alloy by nzeans oj dilatometry, melallography, and electron microscopy. Upon "slozc" heating (-1°C per min) length cJmnge us temperature plots showed u gradual contracLion over the temperature range 200" to 280"C ,followed by a more abrupt contraction beginning a1 -280°C. Howet,ev, zchen the heating rate was increased -4°C per tnin, no gradual contraction was observed and only the abrupt contraction starting at -2BO"C was found. Thus on slower heating- the AS "temperature" for the subject alloy, unlike the MS temperature, is better defined as a range of temperatures. Both optical and transmissiorl electron microscope observations showed that some of the martensite plates exizibited a partial loss of transformation twins during reversal. The midvib region of the martensite plates disappeaved relatively early duirng the reversal. Metallographic observations slowed that the earliest detectable stage of the rezlerse tvansforrvration begins (axd Moues inulardly) at The Martensens i te - parent interface. At higher temperatirres, the. formation of martensitically reversed jcc plates within the bcc martensite plales was observed. It is concluded that the reverse transformation consists of a diffusion less process (martensitic); but this is ps-obably aided by a prior or simultaneous dijjusiorz-comltvolled process, at leasl in the case of slower heat-ing' experiments. ALTHOUGH numerous investigations have dealt with the parent-to-martensite ("forward") transformation (fcc — bcc) in Fe-Ni alloys, comparatively little is reported on the ("reverse7') martensite-to-parent transformation.'-4 Even though such reverse transformations have been studied in detail in some nonferrous systems, one of the difficulties of studying the reverse transformation in most ferrous mar-tensites is that the martensite decomposes by tempering during heating. However, carbonless Fe-Ni alloys do not exhibit this difficulty since the transformation in these alloys is completely reversible. The present investigation represents an attempt to shed more light on the nature and mechanism of the martensite-to-parent transformation. 1) EXPERIMENTAL PROCEDURE 1.1) Alloy Prepatation. Fe-Ni alloys of compositions near 34 wt pct Ni were prepared from zone-refined iron (99.994 wt pct Fe) and high-purity nickel (99.999 wt pct Ni) by induction melting in recrystallized alumina crucibles in an argon atmosphere, with prior vacuum evacuation to 10"3 mm Hg. The alloys were homogenized by induction stirring in the molten state for 5 min. After solidification, the alloys were further homogenized in evacuated quartz capsules for 96 hr at 1230°C. 1.2) Dilatometry. Slices of the ingot were hot-forged (750°C in air) into approximate rod form and these specimens were then hot-swaged (750°C in air) into long cylindrical rods 0.55 mm diam. From the rods, specimens about 1 in. long were cut. These were then vacuum-annealed for 24 hr at 1200°C, cooled to room temperature, and subsequently transformed to martensite in liquid nitrogen (whereby about 40 pct transformation was obtained). Dilatation measurements were made by observing length changes in a vacuum dilatometer with an externally mounted LVDT sensing element. 1. 3) Preparation of Electron Microscope Specimens. Slices of the ingots were cold-rolled (with intermediate vacuum anneals) to -0.020 in. Out of these rolled sheets, specimens (about 1 by 1 in.) were cut. These were then vacuum-annealed, transformed to martensite by cooling in liquid nitrogen, and subsequently heated from room temperature to various temperatures to effect either partial or complete reverse transformation. These specimens were then chemically polished to 0.002 in. in l:l HsOz (30 pct) and &PO4 (85 pct) solution, and thinned to electron transparency in an electrolyte consisting of 150 g CraOs, 750 ml glacial acetic acid, and 30 ml ~~0.~ Observations were made with a 100-kv Hitachi HU-11 electron microscope equipped with an HK-2A tilting device. 1.4) Optical Microscopy. Metallographic observations were made with a Leitz MM5 metallograph on the same 0.020-in. sheet specimens as were used for electron microscopy and on bulk specimens which were 0.2 in. or more on a side. The chemical thinning solution when cooled below 20°C also served as an etchant for this alloy. Observations of surface relief were made with a Zeiss interference microscope employing a Thallium light source of wavelength 0.54 p. Specimens for interference studies were prepared by two-stage polishing on Buehler vibromet polishers using 0.3 and 0.05 p alumina abrasives. 2) EXPERIMENTAL RESULTS 2.1) Comparison of the MS,AS, and Af Tempera-tures wTth Previous Re sults. The AS aLd Af tempera -tures of several Fe-Ni alloys were determined dila-tometrically. The MS temperatures of the same alloys were determined by continuously lowering the temperature using a mixture of isopentane and liquid nitrogen and observing the highest temperature at which a prepolished specimen showed surface upheavals. For the present the As temperature is defined as the temperature at which an abrupt decrease in length occurs in the dilatation plot. The Ms,As7 and A determinations in the present investigation and those of Kaufman

Jan 1, 1968

By Harry Gard Knox, F. R. Harris

This paper covers some of the problems presented to the oil industry in the drilling of oil wells in the open waters of the Gulf of Mexico. The hazards, delays and relative costs of offshore drilling are reviewed and various forms of drilling platforms discussed. The requirements of the offshore drilling rig are summarized together with the principal items affecting the cost of construction. Sea waves and their size and characteristics as affecting offshore platforms are reviewed. Drilling platforms are classified as fixed, or fixed and floating. Fixed platforms of the conventional cofferdam and pile-supported type are discussed together with their good points and their limitations. The desirability is pointed out of eliminating as much offshore work as possible where operations are subjected to constant and expensive delay and substituting therefor the prefabrication of structures ashore or in sheltered waters. Marked economy will come with the standardization of offshore rigs aid special means of transporting them to the site. Several types of structure which are partly pile-supported and partly buoyancy-supported are discussed and their possibilities of future usefulness commented upon. General Considerations The predominant attribute of offshore drilling equipment is that it must be equal to the job in hand. We therefore give first thought to the matter of adequacy. In view of the probable depth of drilling, the investment involved and the per diem labor costs, it is assumed heavy modern drilling equipment will be employed. In order to usc such equipment efficiently, the working deck must be ample in size and strength and supported so as to be relatively free from motion and from green seas even in heavy storms. These requirements necessitate a high and rigid land-based support for the drilling rig and machinery with plenty of space for supplies, such as pipe, mud, water and fuel, with reserves for days when transportation from shore is impracticable. In offshore rigs the crew will be housed onboard in comfortable quarters, probably air conditioned and equipped with a galley and refrigerated food storage. An important consideration will be the ability to transfer stores and crew to and from the rig in all but the heaviest weather and the platforms must be protected from the impact of supply vessels when alongside. It will be essential to maintain continuous communication with shore by radio or cable, not forgetting the possibility of a helicopter landing space for the transfer of crew and light stores as well as a means of general communication. Whatever structure is constructed must be secure from storms of hurricane force and a safe place for the operating crew to work. If the well comes in, the drilling rig will presumably be removed and a small but rugged pile-supported platform will remain to carry the Christmas tree with safe working space around it. It will be protected from damage on all sides by buffer piles or dolphins. It is assumed that the flowing oil will be piped to storage tanks in the vicinity of the well. An individual tank for each well or a

Jan 1, 1949

By J. E. Campbell, G. D. Calkins, N. M. Ewbank, M. Pobereskin, A. Wesner

GRINDING for size reduction affects the economics of many processes and products. It is essential as the first step in many industrial processes and is also a finishing step for materials with properties depending on particle size, such as talc, cement, and silica sand. Intermediate and fine grinding are vital operations in the U. S. cement industry, which is producing more than 250 million bbl of cement per year.' Wear of the grinding media is a large part of the grinding operation cost. Problems encountered in grinding cement are so complex that evaluation of efficiency and economy of grinding media is difficult.2 It has been especially difficult to evaluate the relative effectiveness of different types of balls because there are no good testing techniques. Many other industrial operations can be evaluated on a laboratory scale with reasonable accuracy. This does not hold true for evaluation of grinding balls. The consistent results obtained in a laboratory test under a given set of conditions are not always borne out in field application. Rough evaluations of the effectiveness of various compositions and types of grinding balls have been made in the field by using a full charge of one type in a mill and comparing the production record with another run using another type of ball. This method is time-consuming and not very precise, as the second run may not have been carried out under identical conditions. Laboratory-scale tests, on the other hand, have yielded inconclusive results, and many investigators have turned their attention to the development of a field testing technique. Field testing small sample lots of grinding balls has been impractical because it is difficult to identify and recover the test specimens from the grinding mill, and individual groups of balls that have undergone different heat treatments can not be separated.".4 To overcome these difficulties, previous investigators have identified the balls by distinctive marks, notches, and drilled holes, but this procedure has three serious drawbacks: 1) Grinding characteristics and quality of the steel balls may be affected. 2) Physical markings may be worn away in the grinding process, especially during a prolonged run. 3) Recovery from the bulk of the charge will be extremely difficult because the markings are hard to see and may be masked by a coating of the product. To circumvent these difficulties, a radioactive-tracer technique was proposed for recovery and separation of steel grinding balls and subsequent evaluation of the various compositions of the balls. The proposed technique involved five basic operations: 1) Thermal-neutron irradiation activation5 of each group of test grinding balls to a different level of specific radioactivity. 2) Addition of groups of radioactive steel-ball specimens into a ball tube mill. 3) Recovery of radioactive steel-ball specimens from the bulk of the mill charge. 4) Separation of the various groups by their specific radioactivity. 5) Evaluation of actual grinding ball wear. Before any physical tests were performed, required neutron irradiation intensity and time were calculated. Probable composition of the steels to be used was ascertained. An examination was made of the radioactive nuclides8 to be formed which would contribute measurably to the radiation level immediately after irradiation and during the test operation. The radioisotopes formed, their types of radiation, and their half lives are listed in Table I. Of these radioisotopes only iron-59 and chromium-51 were significant for the actual wear test. The intensity of radiation that could be detected by a Geiger counter when the test was completed was the basis for the minimum activation level established. The intensity of radiaton that could be safely handled at the beginning of the test was the basis for the maximum activation level, although this was not considered a major problem. Ten groups of grinding balls of various composition and/or surface or heat treatment were to be tested. One group was designated for the minimum irradiation time. The remaining groups were designated for irradiation periods that increased by increments of 33 pct from that of each preceding group. This difference was considered enough for separation and identification of the groups by comparison of specific activity. Potential Hazards: Possible radiation hazards that might be encountered during this experiment were evaluated for the three important phases: 1) the radiation hazard of placing balls and removing them from the mill, 2) contamination of the product cement by radioactive material worn from the balls, and 3) contamination of the steel by the radioactive balls left in the mill. The radiation intensity expected from the whole group of radioactive balls was calculated to be 250 milliroentgen per hr at 1 ft. This meant the balls would require special shielded packaging and warning labels on the shipping containers. In a radiation field of 250 mr per hr a man can work for 1 hr without exceeding maximum permissible weekly exposure. Since the balls could be dumped into the mill in a matter of seconds, relatively little radiation exposure was anticipated at this stage of the operation. If the weight loss in the balls was 7.7 pct per month and the cement feed through the mill was

Jan 1, 1958

By George M. Fowler, R. E. Illidge

Part I. Developing BY GEORGE M. FOWL INTRODUCTION The Tri-State district comprises an area of about 2000 square miles in southwestern Missouri, southeastern Kansas, and north [ ] eastern Oklahoma. The part that is in and contiguous to Missouri is still sometimes designated as the Joplin district (Fig. I). EARLY OPERATIONS Mining operations in what is now the Tri-State district date from about 1848 and have been continuous to the present. Apparently the first discoveries of ore were made about the same time near the present sites of Joplin, Oronogo, and Granby. Lead minerals were found at grass roots, probably in shattered rock in shallow excavations, then these minerals were followed in shear zones to deeper horizons. The mining of zinc followed. Before 1874, zinc ore was worthless and discarded as waste. According to published records, the total production of lead to that date was 49,000 tons of metal from 70,000 tons of concentrates. PRODUCTION The aggregate ore production from the Tri-State district was recorded at interval

Jan 1, 1943

By C. Ernest Birchenall, Robert F. Mehl

Application of diffusion laws in the customary form to experimental studies in binary metallic solid solutions has shown the diffusion cocfficient to vary with concentration for all systems investigated. The factors determining this variation have not been ascertained. However, the question of whether the diffusion coefficient would become a constant, independent of concentration throughout a single phase if the concentration gradient in the diffusion equation were replaced by an activity gradient has been an attractive subject for speculation. Wagner¹ derived an expression for the force acting on a diffusing particle in terms of the chemical potential. This was also the approach chosen by Jost2 in his monograph. From a somewhat different point of view, Eyring3 and his co-workers have used activity gradients when dealing with diffusion in concentrated nonideal solutions. The only actual test with experimental data is that given by Darken,4 though this is more qualitative than quantitative. Many others opposed the application in any way of thermodynamic concepts to kinetic phenomena, including diffusion processes. A rigorous examination of this principle requires good data expressing the relationship between activity and concentration for solid solutions for which reliable diffusion work has been done. The literature provides such information only for the interstitial solution of carbon in gamma iron (austenite) and for the substitutional copper-zinc solutions (alpha brass). Activity data for carbon in austenite at 800°C and 1000°C are available from the recent work of Smith5 on the equilibrium of hydrogen-methane and carbon monoxide-carbon dioxide mixtures with gamma iron. Combining these with the diffusion studies of Wells and Mehl6 makes possible a quantitative test for this interstitial solid solution. The vapor-pressure determinations for zinc over brass by Hargreaves7 allowed the calculation of activities in this system over a wide range of temperatures and concentrations. Extensive investigation of diffusion in this substitutional solid solution has been carried out by Rhines and Mehl.8 Activities in Brass9 If the vapor phase of zinc is assumed to behave as an ideal gas, any solid or liquid solutions that are in equilibrium with the same partial pressure of zinc at the same temperature have the same thermodynamic activity of zinc. In order to assign a numerical value to the activity azn, it is necessary to choose some standard reference state to which an activity value of unity is arbitrarily assigned. It is customary to choose the liquid or solid state of the pure material. Then azn is defined numerically by

Jan 1, 1947

By C. Ernest Birchenall, Robert F. Mehl

Application of diffusion laws in the customary form to experimental studies in binary metallic solid solutions has shown the diffusion cocfficient to vary with concentration for all systems investigated. The factors determining this variation have not been ascertained. However, the question of whether the diffusion coefficient would become a constant, independent of concentration throughout a single phase if the concentration gradient in the diffusion equation were replaced by an activity gradient has been an attractive subject for speculation. Wagner¹ derived an expression for the force acting on a diffusing particle in terms of the chemical potential. This was also the approach chosen by Jost2 in his monograph. From a somewhat different point of view, Eyring3 and his co-workers have used activity gradients when dealing with diffusion in concentrated nonideal solutions. The only actual test with experimental data is that given by Darken,4 though this is more qualitative than quantitative. Many others opposed the application in any way of thermodynamic concepts to kinetic phenomena, including diffusion processes. A rigorous examination of this principle requires good data expressing the relationship between activity and concentration for solid solutions for which reliable diffusion work has been done. The literature provides such information only for the interstitial solution of carbon in gamma iron (austenite) and for the substitutional copper-zinc solutions (alpha brass). Activity data for carbon in austenite at 800°C and 1000°C are available from the recent work of Smith5 on the equilibrium of hydrogen-methane and carbon monoxide-carbon dioxide mixtures with gamma iron. Combining these with the diffusion studies of Wells and Mehl6 makes possible a quantitative test for this interstitial solid solution. The vapor-pressure determinations for zinc over brass by Hargreaves7 allowed the calculation of activities in this system over a wide range of temperatures and concentrations. Extensive investigation of diffusion in this substitutional solid solution has been carried out by Rhines and Mehl.8 Activities in Brass9 If the vapor phase of zinc is assumed to behave as an ideal gas, any solid or liquid solutions that are in equilibrium with the same partial pressure of zinc at the same temperature have the same thermodynamic activity of zinc. In order to assign a numerical value to the activity azn, it is necessary to choose some standard reference state to which an activity value of unity is arbitrarily assigned. It is customary to choose the liquid or solid state of the pure material. Then azn is defined numerically by

Jan 1, 1947

By William Marsh Baldwin

[Two of the most useful and important equations available to the metallurgist for the study of plastic deformation of metals are the Huber-von Mises-Hencky1-3 and the St. Venant7-10 equations. HUBER-VON MISES-HENCKY EQUATION The Huber-von Mises-Hencky equation answers the question: When does plastic flow occur in metal that is subjected to a multi-axial stress? It occurs, according to this equation, when the three principal stresses,? al, a2, and a3 satisfy the equation: (s1 - s2)2 + (s 2 - s 3)2 + (s 1 ? s3)2 = 2K2 [I] Here K is the yield strength of the material as determined in an ordinary tensile test. If the quantities a1, a2, and a3 are assigned to the coordinates of a Cartesian three-dimensional system, this expression describes a cylinder whose axis of symmetry is inclined at equal angles to the three coordinate axes4,5 (Fig. I). The radius of this cylinder is v2/3K. For the purpose of simplicity, it is sometimes advantageous to ascribe the values s 1/K = si, s 2/K = s2, s 2/K = s3 to the three coordinate axes instead of the principal stress alone. In this case, Eq. I becomes (s1 - S2)2 + (S2 - S3)2 + (Sl - S3)2 = 2 [2] and the radius of the cylinder becomes 2/3v. In the latter method of representation, a point lying inside the cylinder indicates that the metal will react elastically, whereas a point lying on the cylindrical surface indicates that the metal will behave plastically. Some of the geometric features of this cylinder are worthy of study. Let us inquire first as to what interpretation may be placed upon what we will choose to call the "circles of latitude" of the cylinder (L in Fig. I) and the "meridians" of the cylinder (M in Fig. I). Circles of Latitude Circles of latitude are formed by allowing a plane, passing perpendicular to the cylinder axis, to intersect with the cylinder. Any point, P, on this circle is presumed to have the coordinates s1, s2, and s3. The coordinates of the point resulting from the intersection of the plane and the cylinder axis will be a, a, and a (since the cylinder axis is equally inclined to the three coordi¬nate axes). Let us now pass a line through the point on the circle and the point on the axis.]

Jan 1, 1946

By R. Sporcic, P. J. Mudra

During the past year personnel of the Roof Control Research Group of the Bureau of Mines designed and developed encapsulated hydraulic cells for measuring pressure changes in coal in situ. Preliminary results from feasibility tests in progress in the laboratory and field indicate that the cells respond favorably to changes in pressures associated with a coal-mining environment. The ultimate objective is to use these cells to obtain engineering information relating to coal bump or coal outburst phenomena. Mining research has experienced a remarkable growth during the past decade and from all indications should surge forward at even a greater pace in the future. This increased interest in mining research has been brought about by the ever-multiplying number of technical problems being encountered by the mining industry in its effort to produce pay-dirt tonnages safely and economically from greater underground and surface pit depths. Among the various divisions in the field of mining research, the study of ground stress has received a large part of the overall attention. Numerous technical papers have been written with regard to ground stress conditions around mine openings and yet the total usable knowledge concerning this subject is extremely limited. Research teams around the world are endeavoring to bridge the gap between theoretical and laboratory approaches and the solution to design problems in the field. The problem of ground stress is not a new one for the coal mining industry. Operators in both eastern and western coal fields of the United States as well as in many foreign countries have long been plagued with a number of ground stress problems, one of which is commonly referred to as the coal-mine bump. This term or phenomenon has been aptly defined by earlier investigators as the violent and sudden failure of coal and adjacent rock. Direct results of such failures have been the loss of human lives and thou- sands upon thousands of dollars of sustained mine damages. In an effort to alleviate the magnitude and frequency of these failures, mine operators have employed and are presently employing various corrective techniques. These include: Inducing failure in heavily stressed areas by augering large-diameter holes into stressed pillars, using extensively yield-able steel arches in both long-term haulage and short-term face entries, backfilling unused or abandoned entries with mine waste to gain additional support, and using systematic pillar coal panel extraction techniques including mechanized longwall mining. The Health and Safety Activity of the Bureau of Mines has for a number of years contributed considerable time, funds, and talent in an effort to define better the ground stress problems associated with coal-mine bumps. As a part of this investigative program, in situ ground pressures are presently being studied in coal mines located in West Virginia and Utah. The description and development of the device being used to measure these pressures is the specific topic of this paper. CHOICE OF INSTRUMENTATION After consideration and evaluation of the various instruments and techniques that are being used by researchers in the field of rock mechanics to detetmine in situ stresses, a simple hydraulic system was selected for detailed investigation. Aside from simplicity, a hydraulic system is relatively inexpensive and also eliminates the need for electricity in its installation and operation. The hydraulic device referred to is, in essence, a simple unidirectional pressure-measuring cell. Hydraulic cells, which had been used for measurement of pressures in hard rock, were investigated but found not entirely suitable for use in coal, particularly since they involved (1) preparation and emplacement of cement grout at the test site, and (2) a waiting period before the cells became operational. At the outset, it was decided that certain design parameters be established. The cell should be simple and inexpensive, constructed of materials readily obtainable and easily built in the laboratory or field by unskilled labor. It was further decided that it was desirable to encapsulate the cell in a suitable mate-

Jan 1, 1963

By J. W. Spretnak, G. W. Cunningham

Grain growth across the bond region in Pressure bonded copper was found to be mainly dependent upon the presence or absence of microvoids, but it was also found that prior history, bonding pressure, bonding time, and bonding temperature are important variables. An increase in pressure, time, or temperature tends to promote grain growth in the interfacial region. Polygonization is observed after pressure bonding except for specimens previously annealed at temperatures on the order of 1800°F or higher. The dislocation density in bonded specimens was found to be greater in the bond region. THE bonding of metals by the application of gas pressure at elevated temperatures is a relatively new process, having been developed over the past 10 years. The technique, as described by Paprocki, Hodge, and Boyer,l is unique in that assemblies of many parts and complex shapes can be bonded with a negligible amount of deformation. The process thus differs metallurgically from pressure welding, cold welding, and recrystallization welding in that deformation occurs only in a microscopic region whereas, in general, the welding requires severe deformation and may extend the contact surface by a factor of 3 to 10 during the welding. From a practical standpoint, pressure welding is not amenable for bonding large surfaces. During the time in which Paprocki and coworkers were deve1oping the process, West2 established aproc-ess,for bonding aluminum to uranium, and Barnes and Maze? developed a gas-pressure-bonding technique for nickel and copper. Recently, Fugardi and Zambro4 have used equipment similar to that developed by Paprocki and coworkers to establish parameters for bonding stainless steel, aluminum, and zirconium. Most of the investigations on pressure bonding have been empirical in nature and, although methods have been developed for bonding such metals as molybdenum, columbium, titanium, zirconium, and stainless steel, the information concerning the mechanism of bonding is limited. Several workers5"7 have studied the pressure bonding of dissimilar metals in order to gain information on diffusion and formation of inter-metallic phases under application of pressure. Clapson and Robbins8 have shown by a series of annealing studies that voids in the interfacial boundary of roll-bonded copper can prevent movement of the boundary until the voids are spaced far enough apart to prevent pinning. They also indicated that recrystallization and grain growth can eliminate the voids. In this paper it is shown that voids are the major detriment to grain growth across pressure-bonded interfaces, but it is also shown that prior history, bonding pressure, bonding time, and bonding temperature are

Jan 1, 1962

By Chester Purington

THE AUTHOR hopes that this paper will meet with criticism and debate by fellow members of the Institute rather than with that attitude of passiv-ity and indifference which one is inclined to adopt when considering a field completely foreign to one's own experi-ence. After several years of study of voluminous literature, maps, and statistics, and many personal journeys and field inspections of various parts of Siberia, the conclusion is reached .that the area adjacent to the Stanovoi, Zhugd-Zhur, and Yablonoi ranges as below defined is that which .is most accessible to the western world and will soonest give results from exploration. HISTORY The first incursion of the Russians into Siberia east of the Yenesei River appears to have been in 1632 when the fort of Yakutsk was founded on the middle Lena. The early expeditions were in quest of furs. As the Siberians say, "the sable beckoned" and the post of Anadyr was founded in 1639, two thousand miles further northeast. Thus nineteen years after the Pilgrims landed in Massachusetts, the Russians had established a trading post within 700 miles of what is now the town of Nome, Alaska. Parties of Cossaks penetrated to the shores of the Okotsk1 Sea early in the seventeenth century, but it was not until 1688 that the town of Okotsk was founded. In 1712 a grand project was elaborated at St. Petersburg for building a port at Okotsk, but it came to nothing. Vitus Bering, the Alaska explorer, built ships at Okotsk, and made this his point of depar-ture. It is stated that the iron work used in these ships was brought overland partly from Yakutsk, and partly even from St. Petersburg, 5500 miles away. Accord-ing to report a copper deposit was worked on the river Urak, not far from the coast, and copper was smelted for sheathing the bottoms. Grassgrown mounds con-taining slag and shots of copper were inspected by the writer last summer, at the site of the ancient shipyard.

Jan 11, 1923

By Gustav S. Preller, A. M. Gaudin

Fox the past 20 years it has been generally accepted that the flotation process is made possible as a result of the action of certain chemical substances on the surface of the mineral particles. In fact, it has been suspected, but never demonstrated, that this action produces on the mineral particles a layer of chemosorbed ions that is of the order of magnitude of a monolayer; that is, of a layer one ion deep. It is the purpose of this paper to present certain initial results on the relationship of mineral surface area and collecting-agent requirements. Up to about eight years ago, all considerations involving the surface area of finely divided solids were-limited by the fact that there was not in existence any general method for determining the extent of such surfaces, especially on mixed materials. However, the method invented by Brunauer, Emmett and Teller1 has changed the situation by providing a general procedure (BET method). This procedure has already been applied to mineral dressing problems2 -4 and has now received confirmation as to accuracy by an entirely independent method.5 This confirmatory or "absolute" method uses a very tedious calorimetric procedure and is not suitable for routine determinations; but still another method6 now is available to relate the results obtained by the BET method to those obtained calorimetrically. This Harkins-Jura method has the advantage that it does not require an assumption concerning the parking area per molecule of adsorbate (nitrogen). In the original work by Brunauer, Emmett and Teller the parking area per nitrogen molecule was calculated to be either 13.8Å2. or 16.2Å2. according as the nitrogen was assumed to be closely packed as in crystalline nitrogen or loosely packed as in liquid nitrogen. The initial experimental work from this laboratory2 supported the 13.8Å2. figure; that work was done on glass spheres of measurable geometric area and it was based on the assumption that the glass spheres were truly smooth; any deviation from this assumption would, of course, have made the calculated parking area higher. Harkins and Jura's results suggest that the parking area is not the same for all substrata; furthermore, the average of the 87 measurements cited indicates a "preferred" parking area for the nitrogen molecule of about 15.2Å2., with extreme values at 13.7 and 16.9Å2. The average of 21 determinations made in connection with this study' gave a parking area of 14.3 ± 0.27Å2. In view of this result and of the Harkins and Jura

Jan 1, 1946

By B. J. Harlan

The trying times experienced by the steel industry during the past four years have emphasized the necessity of producing pig iron at the lowest possible cost. The trend in both design and operation of blast furnaces has been toward this end rather than toward securing maximum production from a unit or group of units. In the following discussion the trend in design of stacks and auxiliary equipment will be taken up before operation is considered. Although few furnaces have been constructed in the past few years, the trend is definitely toward larger furnaces with a hearth diameter of 24 or 25 ft. Such a furnace is very flexible, being able to produce efficiently any desired daily tonnage between 500 and-1000 or more. The detail of the design of furnace stacks, with the exception of the top, has changed little in recent years. To decrease the velocity of gas through the throat of the furnaces, thereby reducing flue-dust losses, the stock-line areas are constantly being made larger. The top dimensions of the larger furnaces are usually as follows: Stock-line diameter, 19 to 20 ft.; large bell diameter, 14 to 15 ft.; straight section of throat, 5 to 10 ft. high; inwall batter, 1 to 11/4 in. Pe ft. The ratio between the area of the stock line and the area of the large. bell is usually about 1.85 to 1. The stock-line diameter of some smaller furnaces has been increased to that of the hearth diameter of the stack at the expense of the stack batter. Remarkable decreases in flue-dust production are claimed for the so-called " Venturi top," which is achieved by flaring the stock line, in the form of an inverted cone, from a diameter of 17 ft. at 10 ft. below the large bell closed to a diameter of 19 ft. 6 in. at 3 ft. below the large bell closed. Time alone will tell which of the two designs is the better. Because of differences in raw materials, one top may be better for some plants and the other top for other plants. In the search for lower costs and higher efficiencies all operators are, adopting stoves that will maintain maximum hot-blast temperatures with a minimum gas consumption. To meet these requirements, stove capacity of approximately 7 sq. ft. of heating surface and 1.8 cu. ft. of brick volume is required per cubic foot of wind blown per minute.

Jan 1, 1934

By Nathan C. Rockwood

The title of this paper, I understand, was suggested by professional mining engineers as an opportunity for someone to pose problems rather than to offer solutions for them, but the paper will merely attempt to pose some of the production problems of the mineral aggregates industry in such manner as to create professional interest in their solution by the mining engineer, geologist, geochemist and the metallurgical engineer versed in mineral-dressing technique. Definition of Mineral Aggregates " Mineral aggregates" may be defined as fragments of any rock or mineral used to supply bulk or volume or substance for a given purpose. For example, mineral aggregates are used in portland-cement concrete to provide bulk with the expenditure of the least feasible amount of cement binder. Mineral aggregates are used without port-land cement or bituminous binder in highway and railway roadbeds to provide substance, to carry loads. provide aggregates are used in filters for water and sewage, to provide substance for the liquid to trickle through. These are only a few typical uses of mineral aggregates. For all these uses, strength, toughness, resistance to abrasion, and durability are usually prime requisites; so, while theeretically mineral aggregates may be of any mineral composition, what really is desired is a mineral composition as nearly inert under the conditions of use as anything of earthly origin can be. Exploration and Possibilities of Development The distribution of deposits of mineral aggregate is universal, since almost any part of the earth,s crust can be used; even the top soil is sometimes used in stabilized surfacing for highways or airport runways. Nevertheless there is ample opportunity for exercise of the talents of the mining engineer and the geologist in finding the particular deposit that will be most economical to develop, keeping in mind such considerations as: (i) quality and mineralogical characteristics of the material; (2) size and permanency of the market; (3) final cost of opening and development of the deposit; (4) selection of location of plant; (5) methods and costs of distribution of the product in comparison with both present and possible future competition; (6) selection of the proper type of operating equipment; (7) estimation of probable waste products and their disposal. These are typical but there are other considerations also. Because profit margins are far smaller than in any comparable mining operation, it is all the more logical to assume that a higher degree of expert knowledge is desirable to make a success of a mineral-aggregates business. The industry has much engilleering talent in its operating branch, but it lacks, to a considerable degree, engineering talent with experience

Jan 1, 1948

By Nathan C. Rockwood

The title of this paper, I understand, was suggested by professional mining engineers as an opportunity for someone to pose problems rather than to offer solutions for them, but the paper will merely attempt to pose some of the production problems of the mineral aggregates industry in such manner as to create professional interest in their solution by the mining engineer, geologist, geochemist and the metallurgical engineer versed in mineral-dressing technique. Definition of Mineral Aggregates " Mineral aggregates" may be defined as fragments of any rock or mineral used to supply bulk or volume or substance for a given purpose. For example, mineral aggregates are used in portland-cement concrete to provide bulk with the expenditure of the least feasible amount of cement binder. Mineral aggregates are used without port-land cement or bituminous binder in highway and railway roadbeds to provide substance, to carry loads. provide aggregates are used in filters for water and sewage, to provide substance for the liquid to trickle through. These are only a few typical uses of mineral aggregates. For all these uses, strength, toughness, resistance to abrasion, and durability are usually prime requisites; so, while theeretically mineral aggregates may be of any mineral composition, what really is desired is a mineral composition as nearly inert under the conditions of use as anything of earthly origin can be. Exploration and Possibilities of Development The distribution of deposits of mineral aggregate is universal, since almost any part of the earth,s crust can be used; even the top soil is sometimes used in stabilized surfacing for highways or airport runways. Nevertheless there is ample opportunity for exercise of the talents of the mining engineer and the geologist in finding the particular deposit that will be most economical to develop, keeping in mind such considerations as: (i) quality and mineralogical characteristics of the material; (2) size and permanency of the market; (3) final cost of opening and development of the deposit; (4) selection of location of plant; (5) methods and costs of distribution of the product in comparison with both present and possible future competition; (6) selection of the proper type of operating equipment; (7) estimation of probable waste products and their disposal. These are typical but there are other considerations also. Because profit margins are far smaller than in any comparable mining operation, it is all the more logical to assume that a higher degree of expert knowledge is desirable to make a success of a mineral-aggregates business. The industry has much engilleering talent in its operating branch, but it lacks, to a considerable degree, engineering talent with experience

Jan 1, 1948

By D. T. Peters, S. Floreen

The age hardening behavior of an Fe-8Ni-13Mo alloy was studied after the matrix had been varied to produce either ferrite, cold u~orked ferrite, or nzassive nzartensite. The aging behavior of the cold worked ferrite and murtensite structures were very similar. The martensite aging kinetics were much different from those observed in earlier studies of aging of maraging steels, even though the martensite wzatri.r had the same dislocation structure as those found in maraging steels. The results suggest that the previously observed precipitation kinetics of maraging steels ?nay have been controlled by the nucleation be-haviov, which in turn were dictated by the alloy compositions and the resultant identities of the precipitating phases. IT is well known that the rate of precipitation from solid solution depends not only on the degree of super-saturation, but also on the density and distribution of dislocations in the matrix structure. These imperfections often act as nucleation sites, and may also enhance atomic mobility. 'Thus, the presence of dislocations is important since the type and distribution of precipitates may be determined by them. The precipitate density and morphology in turn affects the mechanical properties of the alloy. A number of studies have been devoted to the precipitation characteristics in various types of maraging steels.'-" These are iron-base alloys containing 10 to 25 pct Ni along with other substitutional elements such as Mo, Ti, Al, and so forth, that are used to produce age hardening. The carbon contents of these steels are quite low, and carbide precipitation is not believed to play any significant role in the aging reactions. After solution annealing and cooling these alloys generally transfclrm to a bcc lath or massive martensite structure characterized by elongated martensite platelets that are separated from each other by low angle boundaries, and that contain a very high dislocation den~it~.~~~~~~~~-~~ Age hardening is then conducted at temperatures on the order of 800" to 1000°F to produce substitutional element precipitation within the massive martensite matrix. Most of the aging studies to date have revealed several common traits in these alloys, regardless of the particular identity of the precipitation elements. Generally hardening has been found to be extremely rapid, with incubation times that approach zero. The agng kinetics, at least up to the time when reversion of the martensite matrix to austenite begins to predominate, frequently follow a AX/~~ = ktn type law, where x is hardness or electrical resistivity, t is the time, and k and n are constants. The values of n are frequently on the order of 0.2 to 0.5, which are well below the idealized values of n based on diffusion controlled precipitate growth models. Finally, the observed activation energy values are typically on the order of 30 kcal per mole, and thus are well below the nominal value of about 60 kcal per mole found for substitutional element diffusion in ferrite. The common explanation of these observations is that the precipitation kinetics are controlled by the massive martensite matrix structure. Thus, the absence of any noticeable incubation time has been attributed, after ~ahn," to the fact that the precipitate nucleation on dislocations may occur without a finite activation energy barrier. The low values of the activation energy are generally assumed to be due to enhanced diffusivity in the highly faulted structure. If this explanation that the precipitation kinetics are dominated by the matrix structure is correct then one should observe a distinct difference in lunetics between aging in a martensitic matrix and aging the same alloy when it has a ferritic matrix. Such a comparison cannot be made with conventional maraging compositions, but could be made with the alloy used in the present study. In addition, the ferritic structure of the present alloy could be cold worked to produce a high dislocation density so that one could determine whether ferrite in this condition would age similarly to martensite. EXPERIMENTAL PROCEDURE The composition of the alloy used in this study was 8.1 pct Ni, 13.0 pct Mo, 0.10 pct Al, 0.13 pct Ti, 0.012 pct C, bal Fe. The alloy was prepared as a 40 lb vacuum induction melt. The heat was homogenized and hot forged at 2100°F to 2 by 2 in. bar, and then hot rolled at 1900°F to $ in. bar stock. The aging lunetics were followed by Rockwell C hardness and electrical resistivity measurements. Samples for hardness testing were prepared as small strips approximately 2 by $ by 4 in. thick. Electrical resistivity was studied on cylindrical samples approximately 2 in. long by 0.1 in. diam. The method for making the alloy either martensitic or ferritic was based on the fact that the alloy showed a closed y loop type of phase diagram. At high temperatures, above approximately 24003F, the alloy was entirely ferritic. Small samples on the order of the dimensions described above remained entirely ferritic after iced-brine quenching from this temperature. In practice, a heat treatment of 1 hr in an inert atmosphere at 2500°F followed by water quenching was used to produce the ferritic microstructure. These samples were quite coarse grained and usually en-

Jan 1, 1970

By R. D. Barer, M. B. Bever

Age hardening alloys are quenched from the solution treatment to room temperature in order to retain a supersaturated solid solution. Some alloys age "naturally" in this condition but in most alloys aging is induced "artificially" by heating to intermediate temperatures. Cold working of the supersaturated solid solution accelerates the aging process and quenching strains have the same effect. The investigation reported here is a study of the progress of aging in specimens quenched directly from the solution treatment to various aging temperatures. This procedure reduces the temperature interval of quenching and the resulting quenching stresses. It also eliminates any changes which would take place in the undercooled sample at room temperature prior to aging at an elevated temperature. Isothermal aging is thus approached and its kinetics may be studied. An aluminum-copper and an aluminum-silicon alloy were chosen for this investigation. The aging mechanism of aluminum-copper alloys is complex while the aging of aluminum-silicon alloys is nearly ideal. As standards of comparison for the samples directly quenched to the aging temperature, specimens were also age hardened by the usual procedure in which solution treated samples are first quenched to room temperature and then reheated to the aging temperature. Review of Previous Work The mechanism of age hardening has been the subject of a controversy which has ranged from the theory of outright precipitation of an equilibrium phase to theories based on subtle changes occurring in the matrix prior to precipitation. A detailed critical review of the literature up to 1939 is available1 and contributions to the general theory of age hardening continue to be made.2,3 Age hardening, whatever its mechanism, involves the nucleation of a second phase within a supersaturated solid solution. Theoretical considerations4,5 indicate that the rate of nucleation reaches a maximum at an intermediate temperature below the temperature at which supersaturation sets in. Studies of precipitation at various subcritical temperatures have demonstrated that the largest property changes in a given time occur at such intermediate temperatures.6,7,8 The precipitation of a phase from supersaturated solid solution is accelerated by strains which may result from quenching or cold work. Phillips and Brick9 established that quenching strains are an essential condition for the age hardening of aluminum-copper alloys at room temperature, at least for aging periods of less than 30 days. They also found that on aging at 300°C the hardness increased faster and reached a higher maximum after quenching into water than after quenching directly to the aging temperatures. Fink and Smith10 observed preferential precipitation on slip bands and grain boundaries in aluminum-

Jan 1, 1950

By J. B. Stubbins, R. A. Blais

Extensive geological work was initiated — and continues — when operations of the Iron Ore Co. of Canada commenced in the Labrador-New Quebec area. Such geological operations include: mapping, test pitting, drilling, underground workings, volume factor and structure tests, and the calculation of ore grades and tonnages. Details of such work are given. Development is carried sufficiently ahead of mining to provide reliable tonnage and grade estimates and allow final mine planning. In order to make full use of geology in mining operations, the pit engineer combines the duties of geologist and mining engineer. The iron deposits of the Knob Lake range are located in the central part of the Labrador peninsula, a territory nearly twice the size of Texas, which is bounded by Hudson Bay on the west, Hudson Strait on the north, the Atlantic Ocean on the east and the Gulf of St. Lawrence on the south. The mining district proper is about 1000 miles northeast of Toronto. A 360-mile railroad links this mining area to the port of Sept-Iles on the Gulf of St. Lawrence. Schef-ferville, which is only a few miles from the open-pit mines, is the center of operations of the Iron Ore Co. of Canada. It has a population of nearly 5000. The nearest settlement is Labrador City, some 120 miles to the south, where this company is erecting a large plant for beneficiating its huge reserves of local low-grade iron ores. HISTORY The mineral possibilities of the area were recognized as early as the end of the last century, when A.P. LOW' of the Geological Survey of Canada made his famous trek across the Labrador Peninsula. After mapping several belts of iron formation, Lovr recommended that the area be thoroughly prospected for iron. In 1929, two well known Canadian geologists, J.E. Gill and U'.F. James, led a private expedition in central Labrador and discovered the first deposit of high-grade iron ore near what is now the Ruth Lake Mine. In 1936 the Labrador Mining and Exploration Co. was formed to 11ake over a prospecting concession of over 20,000 sq miles in central Labrador. An adjoining concession of 3900 sq miles in New Quebec was obtained in 1942 by Hollinger Consolidated Gold Mines, which had just Purchased the Labrador Co. The same year the M.A. Hanna Co. Purchased an interest in both exploration companies. From 1942 to 1950 extensive exploration was conducted by the Hollinger-Hanna technical staff to systematically appraise these vast concessions. More than 40 deposits of high grade ore were found and, by the end of 1950, the total ore reserves reached 418 million tons. In 1949 five American steel companies joined the Hollinger-Hanna interests and formed the Iron Ore Co. of Canada. Financing and full-scale construction were decided upon in 1950. This included the construction of a 360-mile railroad through very difficult terrain, the erection of two hydroelectric plants, the installation of terminal port facilities at Sept-IIes, the building of a modern town-site at Schefferville, the construction of crushing and screening plants, and the preparation of deposits for mining. Ore was first shipped in July 1954. Total open-pit mine production to date is 66 million long tons of direct-shipping ore. GEOLOGICAL ENGINEERING The above achievements would not have been possible without irtegrated teamwork of people of diverse skills and extensive use of geology. In their paper on the role of geologists in the development of this iron ore field, (Gustafson and Moss1 rightly emphasized the difficulties facing the early workers in the area. In an uninhabited land with no roads or railroads and no navigable rivers leading to the interior, everything had to be flown in. It was not until 1948 that aerial photographs and adequate base maps became available. In spite of these and other difficulties, an impressive amount of field work has been done since 1942. Nearly all this work has been directed by geological engineers and geologists. About 15,000 :sq miles have been geologically

Jan 1, 1962

By HENRY FA

HENRY FAY (communication to the Secretary*).-In reply to the discussion of my paper, I wish to take this opportunity to express my appreciation to the Chairman and the various gentlemen who have taken part. I regret that others have not offered criticism, for honest differences of opinion often lead to the truth, and suggest new lines of work. An experiment has been made which bears on Prof. Sauveur's discussion and which helps to emphasize the conclusion that cementation is not a factor in the hardening of: the surface. Dr. Langenberg, of the Watertown Arsenal, has heated for me, in vacuo at 1,000° C., a piece of the metal containing a hard surface. The microstructure shows uniform distribution of carbon throughout the metal, showing that no carbon has been added to .the surface and heating in vacuo has prevented any oxidation of the surface.

Jan 6, 1917