Search Documents

By Lloyd Emory

THE region known as. Guyana or Guiana stretches along the north coast of South America from the mouth of the Orinoco River in Venezuela to the mouth of the Amazon River in Brazil. Politically, it is divided into British, Dutch, and French Guiana, extend¬ ing into Venezuela on the north and into Brazil on the south. Because the area is within the sweep of the northeast trade winds and of approximately the same latitude, plant' and animal life are fairly uniform throughout. The geology is very similar as far as the northern coast is concerned. The drainage is taken care of by a number of large rivers that flow northward directly into the sea. The Courantyne River, which roughly divides the area into half, is the eastern boundary of British Guiana.1 The lower reaches of this river are also the center axis of an ancient bay that at one time indented the coast-line at this point. The old shore-line and, in fact, successive shore-lines can be traced from near the present coast-line in, the northwest district of British-Guiana, south-east and inland, crossing the Essequibo River near Dahli, the Demerara near Christianburg, the Berbice at the mouth of the Kuruduni River and the Courantyne at Vaka-Kuyaha Falls. The line then swings around to the northeast and again approaches the coast near St. Lau-rent in French Guiana. This article will be confined to British Guiana and largely to the valley of the Demerara River, but for geographic names .and topographic details it might, however, apply to Dutch Guiana as well. British Guiana, which comprises about 90,000 sq. mi. and is as large as England, Scotland, and Wales combined, may be divided into three belts, the alluvial belt or coastal plain, the foot-hill area (often spoken of as the sand clay belt), and the hinterland.

Jan 1, 1928

INTRODUCTION Conditions for formation of porphyry copper deposits appear to have been propitious in the Appalachian orogen from the end of Precambrian into Middle Ordovician, and again from Middle Devonian into Mississippian. In the Appalachians we can now record the evolution of a porphyry copper province within a developing orogen, one that reached metamorphic and structural maturity by the end of Devonian. Fig. 15, after Irwin and Coleman (1972), locates that portion of the Appalachian orogen included in this study, and Fig. 16 illustrates general geology of the area. Deposits mentioned in Table 3 and in the text are shown in Fig. 16. Data presented summarize personal observations by the author, published descriptions of specific areas noted in the bibliography, and abstracts from Provincial assessment files. Sources of previously published data are acknowledged. Few comprehensive descriptions of individual porphyry copper deposits in this area exist, so much of the data presented is new to the literature. Porphyry mineralization has, for this chapter, been restricted to porphyry copper de- posits, although porphyry molybdenum de- posits (Clark, 1972) are also shown in Fig. 16 (Hollister, et al., 1974). Copper- molybdenum and tungsten-molybdenum skarns are also omitted to simplify discu sion, though each is known in the area studied. Gaspe Copper is included, however; min- eralization in this deposit is present in the intrusion as well as in the skarn adjacent (Bell and Scott, 1954). Porphyry deposits listed in Table 3 are included because of some important feature, although other deposits have been reported (e.g., Kirkham and Soregaroli, 1975 ) . Clearly, no table now compiled could be complete. The pace of exploration insures that new occurrences will probably be found. Summaries of features exhibited by intrusions shown in Table 3 should remain valid, however, since they appear representative and are based on an adequate number of deposits in the area studied. Paleozoic porphyry copper prospects (shown in Fig. 16) are more common, apparently, in the northeastern part of the orogen, rarely having been found south of Catheart or west of the Logan Line. Occurrences of molybdenum and other associated lithophile elements are, however, known to the south and west as well as further north. Killeen and Newman (1965), King (1970),

Jan 1, 1978

By G. R. Gohn, S. M. Arnold

The results of stress-corrosion tests upon several non-ferrous sheet metals are presented in this paper. The metals include tough pitch copper, five binary brasses, two leaded brasses, one copper-silicon alloy, two tin bronzes, and two nickel-silver alloys. The tests indicate that for most of these sheet metals, externally applied bending stresses below the yield point (0.01 per cent offset) do not result in stress-corrosion cracking as determined by the A.S.T.M. Tentative Method of Mercurous Nitrate Test for Copper and Copper Alloys (B 154-41T).~ Only in the cases of low brass, high brass and medium leaded brass, all cold-worked 4 B & S numbers hard, was any corrosion cracking observed below the yield strength, and in all cases such failures occurred at stresses above the proportional limit for these materials. However, when some of the same materials which showed no evidence of stress-corrosion cracking at stresses below the yield strength, are stressed beyond the yield point, stress- corrosion cracking is quite apt to occur. Since experience has shown that some of these materials, particularly the brasses, are susceptible to stress-corrosion cracking under service conditions, these tests would indicate that, besides externally applied stress and corrosion, plastic deformation in addition to that resulting from the original cold working of the material is also required to produce conditions conducive to stress- corrosion cracking.

Jan 1, 1945

By E. S. Hutchinson

The subject of the influence of coal-dust in mine-explosions has received considerable attention both in England and on the continent of Europe, but until the recent disaster at Pocahontas, Va., it seems not to have been of special interest to engineers in this country. The reason, perhaps, is that most of our bituminous mines are worked by short shafts, slopes and drifts; few have been specially dry; and the explosions that have occurred could readily be traced to fire-damp with 110 complicated circumstances. The object of the present paper is to bring together, for the convenience of members of the Institute, the principal English opinions upon this important subject. Messrs. Lyell and Faraday, in their report to the Home Secretary," in England, on the Haswell Colliery explosion in 1844, seem to have been the first to point out that dust fed the flame originating in a

Jan 1, 1885

By D. Swan

Industrial research may be defined as a critical and exhaustive investigation to create new and better ways of doing things. The results of industrial research are new and improved products, processes, and techniques. This broad definition, of course, covers investigation of all subjects by either individuals or groups of people, and this chapter aims to examine the purpose (what research tries to do), and methods (or how research is done) as applied in the mineral industries. Concepts and History The idea or concept of organized research probably originated in the universities of Europe. There, groups of scholars banded together for discussion and application of their particular specialty to a common problem. Publication of the conclusions drawn from such investigations gave scholars in other areas the opportunity to review and criticize the work of their colleagues, and one of the hallmarks of scientific research work is the publication and criticism of the results of the investigation. It was not until the late nineteenth century that the concept of organized research for the profit of industry was recognized. During the late nineteenth and early twentieth centuries, a large number of industrial enterprises sponsored organizations to study the application of the physical sciences with the aim of making discoveries that would result in profit to the sponsoring organization. The tangible benefits accruing from these activities were so great that they, in turn, fostered several other methods for the support of organized research activities. For the large problems involving public interest, United States Government scientific re- search laboratories were set up. As the demand of smaller enterprises for research activities increased, research institutes and consulting laboratories were organized. In Europe the idea of common industry sponsorship of research centers grew and many large research organizations there were sponsored by associations of manufacturers. Finally, in the United States

Jan 1, 1959

By Christopher M. St. John, Michael P. Hardy

The paper discusses an approach to geotechnical monitoring of a geological repository constructed for the purpose of isolation of high-level nuclear waste, and describes the conceptual framework for development of an integrated monitoring scheme that is initiated during the earliest phases of site investigation and continues through facility decommissioning. The approach that is proposed recognizes the need to provide specific data to support the licensing process for the repository while avoiding adverse impact upon the system performance. Further, it recognizes present and inherent limitations in both the instrumentation and techniques that night be used within a monitoring scheme.

Jan 1, 1982

By George S. Rice

The subject of violent bumps in coal mines has been again brought to attention by a recent succession of such occurrences in the coal mines of the Cumberland field of eastern Kentucky and southern Virginia, which have caused fatalities and injuries to underground employees, a report on which is being issued by the United States Bureau of Mines1. The A.I.M.E. has had two valuable papers on bumps in the No. 2 Mine, Springhill, Nova Scotia, each followed by general discussion on bumps and their causes2. This paper gives a brief review of suggested causes and remedial measures given in English, Canadian and United States reports on blimps in coal mines, and then presents suggestions arising from the writer's recent investigation of the bumps in the Cumberland mines, made at the request of the mine operators, to determine the causes and remedies. These bumps, which occur under the simplest natural conditions, provide better opportunity for analysis of causes and effects than afforded under more complex conditions. The simple conditions in this field consist of relatively thin and level coal beds and uniform roof strata free from folding and faulting. Definition of Bumps Bumps in coal mines, as defined in this paper, are sudden violent bursts of coal that usually occur without warning in the extraction of pillars and may or may not be accompanied incidentally by falls of draw slate, upheaval of bottom and smashing of timbers. They are not known to occur where the advancing longwall method of mining, accompanied by

Jan 1, 1936

By George S. Rice

The subject of violent bumps in coal mines has been again brought to attention by a recent succession of such occurrences in the coal mines of the Cumberland field of eastern Kentucky and southern Virginia, which have caused fatalities and injuries to underground employees, a report on which is being issued by the United States Bureau of Mines1. The A.I.M.E. has had two valuable papers on bumps in the No. 2 Mine, Springhill, Nova Scotia, each followed by general discussion on bumps and their causes2. This paper gives a brief review of suggested causes and remedial measures given in English, Canadian and United States reports on blimps in coal mines, and then presents suggestions arising from the writer's recent investigation of the bumps in the Cumberland mines, made at the request of the mine operators, to determine the causes and remedies. These bumps, which occur under the simplest natural conditions, provide better opportunity for analysis of causes and effects than afforded under more complex conditions. The simple conditions in this field consist of relatively thin and level coal beds and uniform roof strata free from folding and faulting. Definition of Bumps Bumps in coal mines, as defined in this paper, are sudden violent bursts of coal that usually occur without warning in the extraction of pillars and may or may not be accompanied incidentally by falls of draw slate, upheaval of bottom and smashing of timbers. They are not known to occur where the advancing longwall method of mining, accompanied by

Jan 1, 1936

By Robert S. Archer, L. W. Kempf

It is now well known that the structure of aluminum-silicon alloys can be refined in a rather remarkable manner, with consequent improvement of physical properties, by certain treatments applied to the molten metal shortly before casting. The differences between the treated and the untreated alloys are so marked that special terms are used to distinguish them, the untreated alloys being referred to as "normal" and the treated alloys as "modified." The first practical method of accomplishing this result was that of A. Pacz,1 which consists in treating the molten metal with a salt flux of which the active ingredient is sodium fluoride. The result can also be brought about, and in a more economical manner, by the addition of small quantities of metallic sodium (or potassium) to the molten alloy shortly before casting.2 The action of the Pacz flux evidently consists essentially in the production of free sodium by the reaction of sodium fluoride with aluminum. The changing of a normal alloy to a modified alloy is referred to as "modification" and any process for accomplishing this result is a "modifying" process. Modified aluminum-silicon alloys were introduced several years ago, and it has been demonstrated both in the laboratory and in commercial practice that it is no simple matter to produce castings having the maximum or nearly the maximum properties which under favorable circumstances can be obtained. The alloys are rather sensitive to small changes in chemical composition, and the modifying process must be carried out in a very particular manner to obtain the best results. Extensive experimental work has been carried out in the laboratories of the Aluminum Co. of America with the object of determining the conditions that must be observed to make these alloys of the greatest possible value. It was necessary to learn how to control the modifying process

Jan 1, 1926

By R. G. Brown

Tars paper will present a general description of the different mineral belts in the Butte City region (limited, however, to the copper and contiguous silver veins) such as may serve to give an intelligent idea of the distribution and characteristics of the deposits, forming thus a groundwork of information, which it is hoped will have value, when later writers enter into particularized detail.

Jan 1, 1895

By S. A. Braley

DRAINAGE water from coal mines is probably the most serious water pollution problem today, varying in importance according to location of the mines and geological structure. Drainage may be either acid or alkaline in character. Acid discharge, the most severely detrimental to a stream, is caused by natural oxidation of the sulfuritic material (FeS2) in the strata associated with the coal seam. Since the acid is the result of a natural reaction the acid water differs because it does not cease with abandonment of the mining operations. There is no known economical method of neutralizing acid mine water or any practical method to prevent oxidation of exposed pyrite. Since production of acid from a mine does not stop when mining stops, the total quantity produced depends entirely upon the excavated areas. The increasing volume of acid water in manv mines has greatly increased operating costs. Pumping is expensive and acid mine waters are destructive of all equipment, especially metals in pumps and piping, and necessitate the use of corrosion-resistant materials. Discharge of the acid mine drainage into streams neutralizes their normal alkalinity, causes them to become acid, and produces an environment unfavorable for aquatic life and unsuited for industrial or domestic use without costly treatment. Mine drainages vary in percentage composition over wide limits, although the usual dissolved substances are ferrous and ferric iron, aluminum, calcium and magnesium sulfates, and lesser amounts of sodium, potassium and manganese sulfates and chlorides. Some alkaline discharges may contain heavy concentrations of iron as iron bicarbonate. These waters may produce iron hydroxide deposits in the receiving stream but do not cause it to become acid. In the extensive literature on acid mine water there appears to be a great deal of confusion about the importance of various components and the methods for their determination. In many instances faulty conclusions have been drawn from use of unsuitable methods of analysis. It is desirable that the factors and terms used in evaluation of analyses of mine waters should be so clearly defined that any interested person could properly appraise any analytical report. Some analysts report complete chemical analyses of mine waters and neglect to record drainage volumes. Others report only a minimum of analytical data after taking no precautions to preserve the original composition of the water during the time elapsing between collection and analysis. Some use methods of analysis intended for so-called pure waters of the potable and boiler water classes. These methods are not applicable to highly buffered waters such as mine water. Probably the most common criteria for evaluation are pH, free acidity, or acidity or alkalinity to methyl orange or methyl red, total acidity or acidity to hot phenol-phthalein, and the sulfate content. If these determinations are made on carelessly collected samples after a few days to weeks standing in warm rooms, they do not in any way represent the character of the water flowing from the mines. It is hoped that a brief discussion of the fundamental value of some of these factors may lead to a bettqr understanding of the need for more careful evaluation of mine water discharges. The term pH is one used by chemists to express relative acidity or alkalinity in terms of concentration of effective hydrogen ion in a solution. It is defined as the negative logarithm of the hydrogen ion concentration or activity in equivalents per liter. pH = logarithm A neutral solution, which is one containing the same number of hydrogen and hydroxyl ions, has a pH of 7. As the hydrogen ions increase and the solution becomes more acid, the pH decreases toward zero; and as the hydroxyl ions increase and the solution becomes more alkaline, the pH approaches 14. When dissolved in water to a dilute solution acids like sulfuric and hydrochloric, commonly known as strong acids, ionize completely, and the pH or hydrogen ion concentration varies with molar concentration of the dissolved acid. However, in high concentrations of such acids, the pH or hydrogen ion concentration is less than the acid concentration because the acid does not completely ionize. In only very dilute solutions does the pH represent the total amount of acid that can be neutralized by an alkali. All ionization reactions are equilibrium reactions. If other chemicals are added to the solution of an acid and the added chemical produces an ion that is the same as one of the ions of the acid, the degree of ionization of the acid is altered and the pH changes to some value that represents the active hydrogen ion of the new solution. Thus if iron sulfate is added to a solution of sulfuric acid the pH increases, since the common sulfate ion suppresses the degree of ionization of the sulfuric acid and decreases the effective hydrogen ion. However, the total acidity of the solution is increased. There are two salts composed of iron and sulfate— ferrous and ferric sulfate. In these salts there is no hydrogen ion that can ionize to give an acid solution, but when they are dissolved in water, the pH is less than 7 and the solution becomes acid. This is caused by a reaction known as hydrolysis and is represented by the equations FeSO4 + 2H2O ? Fe(OH)2 + 2H + SO,: or Fe,(SO,)3 + 6H2O ? 2Fe(OH)3 + 6H+ + 3504 A solution with a total acidity of 5000 ppm according to the first equation will have a pH of 4.40 but one with an acidity of 75 ppm, according to the sec-

Jan 1, 1958

By J. D. Forrester

Many have been prone to credit the decline of professional interest in some branches of mineral industry education to the industrialists and other agencies who use our graduates. We hear the cry that industrial salaries are too low, opportunities for advancement do not exist, and the mineral industry specifically and generally is not interested in the engineer's efforts. Perhaps the time now has come when we should "dress-ranks," examine our practices, and publicize and encourage advanced technical training instead of laying all our troubles elsewhere. There can be no doubt but that industry is interested and stands ready and willing to co-operate. This is demonstrated by the numerous grants-in-aid and co-operative industrial projects which have been made available to those relatively few schools which have been encouraging graduate study and research. There is no dearth of research problems in any of the mineral industry fields and the sooner we realize the great opportunities for constructive, technical research in all areas of our profession the sooner we will reap the benefits of our engineering enterprises by closer liaison and broader understanding with industry. An analysis is offered here of the status of graduate work and research in various phases of mineral industry education in the United States. It is

Jan 1, 1949

By R. H. Harrington

THE definition of precipitation-hardening is well understood and its principles have been subjected to study for some time. However, the variation of properties with double aging, combined with strain-hardening, gives promise of new and useful phenomena. Properly to understand these distinctions, definitions of these terms are necessary. Precipitation-hardening. This reaction usually depends upon an alloy having such a composition that it consists only, or in major part, of but one phase, a solid solution, at a high temperature, so that, upon slow cooling, this solution breaks down into two phases, the solid solution and a compound. By heating the alloy to the temperature for maximum solution of the compound, quenching, and reheating to a suitable lower temperature for critical dispersion precipitation of the compound, useful properties of the alloy may be developed to a maximum. Double Aging.-Dougle aging in part is similar to the process for precipitation-hardening, consisting of heating a precipitation-hardening alloy to the solution temperature, quenching, reheating to the suitable dispersion precipitation temperature, strain-hardening, and again reheat-ing to a suitable temperature to develop certain useful properties to a maximum. The strain-hardening may be induced by two methods: (1) a rate of cooling from the first reheat may suffice to strain the solid solution lattice of the alloy; or (2) the alloy may be cold-worked to a suitable degree between the two reheats.

Jan 1, 1936

The key-note of good writing, as of good manners, is B natural. Sincerity is the first requisite for effective writing. When a man says what he knows or believes, he is likely to be interesting, because each human being possesses an individuality, a point of view, or a range of sympathy that makes him different from his fellows. To say or to write what you do not think, for the mere sake of talking or writing, is a verbal exercise that must be performed with extraordinary skill if it is to be attractive. Affectations are rarely attractive, rarely effective. To be natural is to be yourself, not a poseur; to give the reader the best of yourself, instead of re-warming the baked meats of yesterday. Quotations-which are second-hand thoughts-will serve occasionally when the thing you want to say has been said so well by another that it would be waste of energy to try to say it better; gut, as a rule, the utterance of the writer himself is more interesting than the quotation, because the writer brings something of himself to bear on the subject, and for the moment is more in touch with the reader than any dear departed author. Therefore, say things as best you can in your own way, neither in borrowed words nor in the phraseology that mimics another. Write as if you were speaking to a person whom you desire to persuade or convince. You will then write better than you speak, because, in the first place, you can be more deliberate, and, secondly, you can revise what you have written. Speaking and writing are similar mental acts, with a difference: the difference between eating food raw and eating it cooked. Some kinds of food gain nothing by being cooked; likewise some kinds of utterance are not bettered by being written down first; but most expressions of thought, especially

Jan 1, 1931

By C. Ernest Birchenall, Robert F. Mehl

APPLICATION of diffusion laws in the customary form to experimental studies in binary metallic solid solutions has shown the diffusion coefficient to vary with concentration for all systems investigated. The factors determining this variation have not been ascertained. However, the question of whether the diffusion coefficient would become a constant, independent of concentration throughout a single phase if the concentration gradient in the diffusion equation were replaced by an activity gradient has been an attractive subject for speculation. Wagner1 derived an expression for the force acting on a diffusing particle in terms of the chemical potential. This was also the approach chosen by Jost2 in his monograph. From a somewhat different point of view, Eyring3 and his co-workers have used activity gradients when dealing with diffusion in concentrated nonideal solutions. The only actual test with experimental data is that given by Darken,4 though this is more qualitative than quantitative. Many others opposed the application in any way of thermodynamic concepts to kinetic phenomena, including diffusion processes. A rigorous examination of this principle requires good data expressing the relationship between activity and concentration for solid solutions for which reliable diffusion work has been done. The literature provides such information only for the interstitial solution of carbon in gamma iron (austenite) and for the substitutional copper-zinc solutions (alpha brass). Activity data for carbon in austenite at 800°C and 1000°C are available from the recent work of Smiths on the equilibrium of hydrogen-methane and carbon monoxide-carbon dioxide mixtures with gamma iron. Combining these with the diffusion studies of Wells and Mehl6 makes possible a quantitative test for this interstitial solid solution. The vapor-pressure determinations for zinc over brass by Hargreaves7 allowed the calculation of activities in this system over a wide range of temperatures and concentrations. Extensive investigation of diffusion in this substitutional solid solution has been carried out by Rhines and Mehl.8 ACTIVITIES IN BRASS9 If the vapor phase of zinc is assumed to behave as an ideal gas, any solid or liquid solutions that are in equilibrium with the same partial pressure of zinc at the same temperature have the same thermodynamic activity of zinc. In order to assign a numerical value to the activity azn, it is necessary to choose some standard reference state to which an activity value of unity is arbitrarily assigned. It is customary to choose the liquid or solid state of the pure material. Then azn is defined numerically by azn = Pza/Pzn° [I]

Jan 1, 1947

By G. W. Preckshot, N. G. DeLisle, C. E. Cottrell, D. L. Katz

MOST crude oils contain asphaltic substances that may be naturally or artificially precipitated. In the Greeley field, California, this asphaltic bitumen is precipitated during the flow of the oil from the reservoir to the stock tank. The mechanism of such precipitation is not well understood. This paper presents the progress that has been made by using the electron microscope as a new tool and by observing the effects of the streaming potential on the formation of bitumen particles. Crude oils at atmospheric pressure viewed in the electron microscope in very thin films under a vacuum showed no asphaltic particles. A technique of preparing slides of thin films by dilution of the oil with benzene and washing in petroleum ether was used at first, and these observations showed that the solvents caused the formation of the particles, varying from 0.01 to 0.2 micron in diameter. The electrical effects of fluids flowing through porous solid were studied, with emphasis on the formation of colloidal particles by the streaming potential. The streaming potential of crude oil flowing through sand was measured and was shown to be responsible for the formation of bitumen particles. These results bring out a new phenomenon, which may occur when crude oil flows through the porous oil reservoir.

Jan 1, 1942

By C. H. Hewitt, J. T. Morgan

The Fry cocurrent in situ combustion project was carried out in a 3.3-acre portion of a lenticular body of Robinson sandstone of Lower Pennsylvanian age. This particular sand body is about 12,000 ft long and 3,500 ft wide; it varies in thickness from 0 to 55 ft, trends northeast-southwest, and occurs at depths between 880 and 936 ft. The reservoir is made lip of three distinct types of sandstone, each having characteristic reservoir properties. (See Table I.) Textural gradients, sedimentary structures, erosional basal contact, absence of marine fossils, and geometry of the sand body all indicate that the sandstone is of fluvial origin and part of an extensive complex of river-deposited sedirnents. Geographically oriented cores reveal that the direction of depositing currents was to the southwest, parallel with the sand-body trend. Directions of maximum pernleability also parallel the northeast-southwest trend. The layered nature of the sandstone reservoir and its directional properties have controlled the areal distribution of produced gas, the ignition behavior, and the vertical profile and horizontal extent of the conbustion zone. INTRODUCTION This paper is the first of a series of three papers that describe Marathon Oil Co.'s Fry in situ combustion test. This first paper contains the results of a detailed study of the geology and reservoir characteristics of the Robinson sandstone reservoir in which the Fry test was conducted. The second and third parts of this series report on the field operations' and performance. The geologic work reiated to cores cut through the combustion zone, and to the effect of reservoir properties on the combustion process is included in the third paper.' GEOLOGIC STUDY OF THE FRY RESERVOIR The close spacing of continuous cores in the Fry combustion site provided an unusual opportunity to study the details of distribution of lithology and reservoir properties within a petroleum reservoir. The objectives of the study were: 1. To determine the distribution of rock types within the Robinson sandstone in the Fry area; 2. To determine the relationship of porosity and permeability to rock properties and establish the distribution and homogeneity of reservoir properties; 3. To determine the origin of the Robinson reservoirs so that attempts could be made to predict the size, shape, distribution, extent and continuity of Robinson reservoirs; and 4. To determine what effects, if any, the reservoir rocks might have on the combustion process, so that the process might be better evaluated. AVAILABLE MATERIALS Continuous cores were cut from 14 wells in the vicinity of the Fry site. Ten of the cores are from within the 3.3-acre pattern; six of the 10 were cut prior to combustion, and four were cut through the combustion zone. Cores from the Emma Fry No. 15, Wampler 0-2 and Fry B wells (Figs. 1, 2 and 9) were geographically oriented by the Eastman Oil Well Survey Co. Maps, electric

Jan 1, 1966

By R. W. Raymond

There is apparently no end to the doubts, inconsistencies and absurdities in which the courts of our mining States and Territories are involved in their attempts to apply to conditions of ever-increasing complexity the provisions of our anomalous mining law. In previous papers, I have called this statute " the law of the apex," because it based upon that vague, novel and mysterious condition the most important grant of title. But the apex is scarcely a more essential feature than the end-lines and the side-lines; for the rights which it may confer may be limited in various ways by these; so that we have, in many a case, the most ridiculous result that the United States, in return for the money of a citizen, conveys to him with much solemnity, under its broad seal, nobody knows what, bounded nobody can tell how. A decision recently made at Butte by Judge De Wolfe, of the United States District Court of Montana, in the case of King et al. vs. The Amy and Silversmith Mining Company, furnishes a fresh illustration of this criticism. The diagram on the following page, constructed without precise regard to courses and distances, simply to assist in the statement of the essential features of the case, will, 1 hope, make clear the principles . involved : The plaintiff occupies a location (the Nonconsolidated) adjoining on the north the defendant's location, a b c d (the Amy), and the disputed mining-ground lies, let us say, in depth under the point W, that is, on the dip of the vein, VD, but not under the surfacelocation, a b c d. The defendant has the prior title, and claims this ground under its extra-lateral right. It is admitted that the apex does not cross the end-line, a d, and does cross the side-line, a b. Whether it crosses, at the other end of the location, the end-line, b c

Jan 1, 1889

By G. G. Sarkar

SHARPNESS of separation and washing efficiency are often confused. The sharpness index indicates the precision of a washing unit; the washing efficiency takes into account not only the unit's precision but also the washability characteristics of raw coal and the near-gravity materials at the effective density of cut. A sound basis for evaluating the sharpness index is essential in comparing the sharpness of separation attained by different cleaning units. Sharpness Index and Related Criteria: Washing plant sharpness of separation has been well represented by Hancock's efficiency chart and Tromp's curve of migrated materials. Some useful coefficients derived from Tromp's curve—the error area, probable error, and imperfection value—have been widely used to measure sharpness of separation. These are defined in a number of papers presented at the first and second International Coal Preparation Colsference held in Paris (1950) and Essen (1954).1-5 In evaluating the performance of a dense medium separator at four different gravities, Yan-cey and Greer6 bserved that even with similar operating conditions and the same size grading of feed, the imperfection value of a washing plant varies through a greater range than the probable error. The present writer also observed the same type of anomalies in comparing the imperfection values of one plant which were determined under almost identical conditions. He therefore devised a graphical method to evaluate a washing unit's sharpness of separation and define it by a single coefficient, which is substantially independent of coal characteristics under normal operation of the unit. Unlike imperfection value, the new coefficient can be expressed on a percentage basis. Coal preparation engineers generally agree that the amount of misplaced material resulting from any separation in a washing plant is almost directly related to the amount of +0.10 sp gr (near-gravity) materials. In actual practice, however, misplacement is not restricted to the 20.10 sp gr range. It will be evident from a study of Tromp curves that this misplacement often extends over unequal specific gravity ranges on the two sides of the actual density of separation. The same condition exists for near-gravity ash distribution and the resultant misplacement of ash units during any separation. But so far as the same unit is concerned, the total misplacements bear a definite ratio to the amount of near-gravity zone materials that is affected by misplacements. This ratio should be constant not only for various densities of separation but also for different qualities of feed coal treated in the same plant. This ratio, multiplied by 100, directly represents the inefficiency of the plant. When the plant inefficiency value is subtracted from 100, the re- ' sult is designated as sharpness index. Evaluating the Sharpness Index: The method of evaluating the sharpness index is explained here with reference to Fig. 1. Fig. 1 is a reproduction of the familiar diagram used by Cerchar of France to represent the inefficiency of a separation in terms of "triangle of errors," which is a measure of organic loss. It will be observed that the characteristic (yield/fractional ash) curve of the raw coal represented by GHAPR

Jan 1, 1958

By E. H. Jr. Dix

THE consideration of alloying elements for aluminum has led to a series of investigations of the equilibrium relations between aluminum and those alloying elements. Therefore, the aluminum end of the aluminum-antimony diagram has been studied. The general form of the aluminum-antimony equilibrium diagram has been worked out by Campbell and Mathews1 and by Tammann.2 Campbell and Mathews described principally the beginning of solidification. They found the curve of beginning of solidification to rise gradually from the melting point of pure aluminum to a maximum at about 67 per cent. aluminum. After a slight lowering of the curve at a little greater antimony concentration the curve again rises to a maximum at 18.4 per cent. aluminum, which corresponds to the compound AlSb. The curve then drops to the melting point of pure antimony. Tammann explained the maximum occurring at about 67 per cent. aluminum as the result of the slow formation of the single compound AlSb. The space lattice of the compound AlSb, according to Owen and Preston,3 is face-centered cubic, the antimony atoms being intermeshed with an identical aluminum lattice. Very little, if any, work has been done on aluminum alloys containing small amounts of antimony.

Jan 1, 1930