Search Documents

By H. Y. Hunsicker

A graphic method has been devised for three-di-mensional analysis of hot deformation and for correlating the amount and directionality of the deformation with resulting directional properties. Deformation is evaluated in terms of dimensional change ratios referred to three orthogonal axes. Since all combinations of the three ratios can be represented in a triangular coordinate field with logarithmic scales, a two-dimensional chart of extent of deformation and degree of asymetry is possible. The entire gamut of shape changes from upsetting through flat-rolling to rod-rolling is accommodated. The resulting coordinate system is a base upon which can be represented the properties of the wrought products measured in the directions of the axes employed fir evaluating the deformation. When property data are available for many types and amounts of deformation, a three-dimensional figure can be constructed, and the projection of this figure is referred to as a ''3d'' chart. Experience in using such charts to plan fabricating operations for a variety of thick-section forged and rolled products of heat-treated aluminum alloys has verified its practical value for optimizing directionality relationships. MechANICAL anisotropy of thick section products of heat-treatable aluminum alloys is recognized by producers and users of these products, and the extent of the directional differences is apparent in property tabulations included in handbooks, standards, and specifications.' Attention has also been directed to the existence of important directional differences in the resistance of these products to stress-corrosion cracking. Metallurgical structure factors responsible for these directional differences include, among other possibilities, shape and alignment of grains, voids and nonmetallic inclusions (when present), volume fraction and spatial distribution of secondary phase particles and solid-state precipitates, crystal-lographic textures, and Bauschinger effect. The contributions of the individual factors vary with alloy composition, heat-treated temper, type of working process (forging, rolling, extrusion), and the amount and directional nature of the deformation. In general, the cast ingot used as the starting material for producing these wrought products exhibits only a modest degree of directionality. A monotonic and continuous transition from this nearly isotropic state with progressive hot deformation would appear probable, assuming that the working temperature is sufficiently high to cause continuous dynamic recovery. Several years ago a project was undertaken to evaluate the effects of hot deformation and metallurgical structures on the directionality of thick wrought aluminum alloy products, and the method to be described was developed as an analytical tool in this investigation. DIRECTION NOMENCLATURE The nomenclature system adopted by industry for the three mutually perpendicular directions employed in testing aluminum alloy products includes four terms: "longitudinal", "transverse", "long transverse", and "short transverse". These terms are conventionally related to the external geometry of the product but also by implication to the deformation and resulting metallurgical structure. Occasions arise in which through use of unusual fabricating methods, intentional or otherwise, the structure does not have the usual relationship to external geometry or may be very complex because of inhomogeneity of deformation throughout the piece. The longitudinal direction is generally parallel to the primary rolling direction or to the direction of extrusion. In the case of forging, it is parallel to the direction of maximum extension (not maximum "working" or "flow", as frequently stated). The term transverse is applied to any direction perpendicular to the longitudinal direction in a product having symmetry about the longitudinal axis, and generally, although not always, the deformation to produce these forms is nearly symmetrical in the transverse plane. This term then may be applied to a round, square, hexagon, or other polygonal, symmetrical shape produced by extrusion or rolling or by forging, if produced by a simple, symmetrical drawing procedure. The type of microstructure generally associated

Jan 1, 1970

By F. R. Brotzen, L. D. Whitmire

Single crystals of high-purity molybdenum were de-formed at temperatures from 195°to 473°K, and the effect of deformation on the electrical resistivily was deler-mined. To separale the resislivity components of point and line defecls some cryslals were annealed at 473°K. The vale of resislivily increase wilh strain was nearly linear and was strongly dependent upon the deformation temperature. Point dejects are annealed out without any effect on the flow stress. At low temperatures the flow stress is a linear function of the square root of the resistivity increase attributable to dislocations. ELECTRICAL-resistivity measurements have been used successfully to gain information on structural changes in metallic materials. During plastic deformation the electrical resistivity rises because of electron scattering from newly created lattice defects. Such measurements lend themselves, therefore, to corroborating results from direct observation of lattice defects and, to a certain extent, to correlating defect densities and distribution with mechanical properties. Published information on research with single crystals of the bcc metals of Group VI, particularly molybdenum, is still limited. Yet, molybdenum single crystals of relatively high purity can be readily prepared by electron-beam-melting techniques. Furthermore, some valuable information on the defect structure of deformed crystals by direct observation is available. Lawley and Gaigher,1 for example, have examined dislocation configurations in deformed molybdenum crystals by means of transmission electron microscopy. Their results revealed that the dislocation density and distribution were strongly dependent upon the deformation temperature. These findings differed from those by Keh and weissmann,2 who found that the average dislocation density in polycrystalline iron deformed between 138° and 298°K depended only on the degree of strain and not on the deformation temperature. Martin3 and peiffer4 showed that point defects introduced in polycrystalline molybdenum by cold work can be eliminated by annealing at a relatively low tempera-ture. In view of their work it became apparent that resistivity measurements of suitably annealed crystals could disclose changes in their dislocation structure and contribute to the understanding of the work hardening of molybdenum crystals. EXPERIMENTAL PROCEDURE Crystals were grown by electron-beam zone melting5,6 of 0.062-in.-diam molybdenum rods (99.99 pct) supplied by General Electric Lamp and Wire Division, Dover, Ohio. The crystals, about 4 in. long, were prepared by using five zone-refining passes at a speed of about 6 mm per min in a vacuum of about 5 X l0-6 Torr. The resistivity ratio of the crystal, p(4.Z°K)/p(273°K), was generally near 10-3. These crystals were used as tensile specimens of uniform diameter in the "as-grown" condition. They were oriented for maximum shear on the (011)[111] slip system (Schmid factor >0.49). The specimens were held in spherically seated Templin-type grips so as to minimize bending. Samples were deformed on an Instron machine at a strain rate of about 5 X 10-5 sec-1 in an isopentane bath with dry ice at 195°K, in ice water at 273°K, and in a vegetable-oil thermostat at 373° and 473°K. The temperature in the latter was maintained constant within +2°K. Resistance measurements were carried out with a Kelvin double bridge. The resistance of the potential leads was kept low by using large-diameter wires outside the low-temperature bath. Many of the resistance data were checked by measurements made with an ac bridge. Current and potential leads were spot-welded to the specimens. The distance between the potential leads, about 3 in., was also considered to be the gage length for the strain measurements. Diameter and gage length of the samples were measured optically with an error of less than 2 pct. These measurements were used also to insure that the deformation had been uniform over the gage length of the specimen. Resistivity changes were then determined from the resistance measurements at 4.2°K assuming constancy of volume. In the course of a test, the crystal diameter, gage length, and resistance at 4.2°K were determined first in the initial state and subsequently for various amounts of elongation.

Jan 1, 1968

By S. R. Seagle, R. Schuhmann, N. A. Parlee

Rates of CO evolution and CO absorption were measured for liquid-iron alloys containing from 0.15 to 4.4 pet C, using a modified Sieverts apparatus. The alloys were held in alumina crucibles, so that both crucible-metal and gas-metal reactions occurred simultaneously. The data are interpreted on the hypothesis that the C-O reaction rate is controlled by oxygen diffusion across the boundary layers at the gas-metal and crucible-metal surfaces. CARBON-monoxide evolution from liquid Fe-C-0 alloys is a key reaction in steelmaking processes, both in the steelmaking furnace and in the ingot mold. Also, this reaction probably is an essential step in the desulfurization of iron under blast-furnace conditions, for which carbon is the principal reducing agent or deoxidizer present in the iron. The thermodynamic properties of the solutions of C and 0 in Fe and the equilibria of these solutions with gaseous CO and CO, have been investigated in some detail and are reasonably well understood. However, while these equilibrium data have accumulated in the laboratory, other data have accumulated to show that equilibrium conditions are often not achieved under plant operating conditions. Thus, an understanding of the rate and mechanism of the carbon-oxygen reaction not only has theoretical interest, but ultimately may assume considerable practical importance. Reaction Mechanisms and Rate Equations The over-all reaction under consideration is C (in liquid Fe) + 0 (in liquid Fe) + CO (gas) [I] Although this appears to be a straightforward heterogeneous reaction, involving just two phases (liquid metal and gas), a wide variety of reaction mechanisms has been proposed. Different authors have expressed divergent views as to the nature of the rate-controlling steps. Accordingly, a brief discussion of the possible reaction steps will be given. 1) Homogeneous Reaction Within Liquid Iron— Feild' and Jette2 have applied chemical reaction-rate theory as if the C-0 reaction were a homogeneous, second-order reaction occurring within the liquid-metal phase. This mechanism necessarily produces CO "molecules" dissolved in liquid iron. In order to yield CO gas, the dissolved CO must nucleate CO gas bubbles, and the dissolved CO also must be transported to the bubble surface where it enters the gas phase. However, this mechanism is inconsistent with present concepts of the structure of liquid-metal solutions. 2) Reaction at Gas-Metal Interface—At the surface of contact between gas and metal, a second-order reaction between dissolved C and 0 may occur to produce a CO molecule which enters the gas phase. This reaction presumably involves an "activated complex" structure in the interface. Some such surface mechanism appears essential because the carbon and oxygen do not occur in the same species in the two phases and therefore must react in some way at the surface. At liquid-iron temperatures, calculations based on reaction-rate theory indicate that the surface reaction must proceed extremely rapidly and thus cannot be a rate-determining step in the C-O reaction under ordinary conditions.3 ccordingly when the over-all reaction is measurably slow, the surface reaction may be considered at equilibrium; that is Cc* Co* = m'Pco [2] in which Co* and Co* are the concentrations of carbon and oxygen (weight per unit volume of metal), respectively, in the liquid-metal phase at the interface, Poo* is partial pressure of CO in the gas phase at the surface (atmospheres), and m' is the mass-action constant for Reaction [I]. Since activities of C and 0 are not strictly proportional to concentrations, m' is not a true thermodynamic equilibrium constant but varies with carbon content.' 3) Mass Transport—If the reaction is to proceed at the gas-metal surface, as described above, dissolved carbon and oxygen in the liquid iron must come to the surface and gaseous carbon monoxide must move away from the surface. Details of the mass-transport mechanisms depend on the kind of system under consideration. For a stirred metal bath in contact with a CO gas phase, the transport of C and 0 to the surface can be described by 1 Do Mols CO evolved per sec = — 1/16— Do/do Agm (CO-Co*) = 1/12 Do/do Agm *(Co-Co*) [3] In this equation, Do and D, are the diffusion constants for oxygen and carbon in liquid iron, 6, and 6,. are the boundary-layer thicknesses, A,,,, is the

Jan 1, 1959

By H. Hansen, A. U. Seybolt, P. Yurcisin, B. W. Roberts

The Bi-Mn phase diagram in the region near BiMn was investigated, using principally thermal analysis and changes in magnetization with temperature. Of chief interest are the findings related to the magnetic transformation in Bi-Mn. THE Bi-Mn system is of both theoretical and practical interest because of the occurrence of the compound BiMn which exhibits unusual ferromagnetic properties. Because the Bi-Mn phase diagram reviewed by Hansen' (see Fig. 1) in 1936 is based on work done by BekierY in 1914 and by Siebe" in 1919, which left considerable doubt about the nature of the diagram. it appeared desirable as an aid in understanding the alloying characteristics and magnetic behavior to examine the pertinent regions of the phase diagram. The most interesting reaction is the peritectic at 445°C which forms BiMn by the reaction: Liquid + Mn(sulfield) ? BiMn(sol field) There is also a eutectic at 262° C between pure bismuth and BiMn. Hansen draws in BiMn dotted, since in 1936 evidence for its existence was uncertain. Experimental Materials—Preparation of Alloys Electrolytic manganese of about 99.97 pet purity and bismuth of 99.99 + pet purity were used as starting materials.

Jan 1, 1957

By C. A. Heiland

MEASUREMENTS of gravity with gravimeters have come into increased use in this country and abroad in the past five years. Probably 100 to 125 gravimeter parties are working in the United States alone. In oil exploration, gravimeter methods have relegated the gravity pendulum definitely to second place, if not third, and now closely rival and possibly surpass the torsion balance in many applications. Gravimeters have lately been applied in mining, although it is doubtful whether they will ever replace electrical or magnetic methods in this work. Notwithstanding the widespread application of gravimeters, there has been no article covering the entire field in the domestic or foreign literature. The purpose of this paper is to meet the demand for com-prehensive engineering information on the subject. The working principles of a number of gravimeters will be, illustrated and treated in relation to the action of corresponding seismometers and astatization methods. The mathematical discussion of theory has been confined to the most necessary fundamentals and been given in as ele-mentary form as possible. A description of calibration methods con-stitutes the last part of the paper. The symbols shown at the top of page 2 will be used in equations throughout the paper.

Jan 1, 1939

By W. Bradley, R. G. Hall

This paper will attempt to show how a metallurgical problem at one California quicksilver mine was solved, and how the solution was applied successfully at another mine. The pronouns "we" and "our," as used below, refer '0 the Bradley 'lining Co. of San Francisco. The term "concurrent firing" for the purpose of this paper can be defined as feeding and firing a a kiln at the same end—that is, of course, the upper end' This is as opposed to "countercurrent firing," the orthodox method, in which a kiln is fed at the upper and fired at the lower end. The terms "quicksilver" and "mercury" are used interchangeably. Early References The earliest work on nonferrous metallurgy, we believe, was The Pirotechnia of Vannocio Biringuccio,l its first edition having been printed in Italy in 1540. Quoting from its chapter entitled "Concerning Quicksilver and Its Ore": Quicksilver ... is one of the gods and has divine strength in itself, and also, to the annoyance of the alchemists, it is winged. Hence, when it sees that it is in gravest danger, it loosens itself from . . . every bond . . . and fies away into the heavens, escaping from the hands of those who crucify it. Almost laughing, it leaves all its adversaries mocked and scorned, with their phials and filters empty . . . How thorough a job, under certain conditions, it can do of mocking its adversaries and leaving their phials and filters empty, was found out four centuries later at the Sulphur Bank mine, on the east shore of Clear Lake, in Lake county, California, The other mine mentioned in the title is the Reed, in Yolo County, California, 35 miles by road southeast of Sulphur Bank, Reed and Sulphur Bank ranked respectively Nth and seventh in U. S. production in 1943. The earliest direct reference we can find to furnacing troubles at these mines was by Thomas Egleston in 1890.2 Speaking of Sulphur Bank, Egleston says: of there is more sulphur than cinnabar in the ore, which is a detriment to both . . . making the sulphur impure, and rendering the cinnabar difficult to work on account of the soot. In some of the early . . . furnaces the accumulation of soot from the excess of sulphur has been known to penetrate as far as the fan blower at the end of the . . . condensers, and completely prevent its revolution. In order to get rid of the inconvenience of this accumulation . . . , as well as to get a commercial value from the sulphur, it (the sulphur) is now separated by steam and sold. It is claimed that the sulphur alone pays all the expenses of ... the mine. The mine was first worked for sulphur, and the cinnabar it contained was considered to be an inconvenience, and was carefully picked out and thrown away, as its richness and value were not

Jan 1, 1949

By Cyril Stanley Smith, Earl W. Palmer

STRIP of any of the metals used for deep drawing operations occasionally yields cups that are defective because of a rim that varies in height around the cup in a wave-like manner Some such defects are traceable to tools or other press factors, but when the protuberances formed (usually four in number on brass and other copper alloys) are symmetrically disposed with respect to the rolling direction of the strip, they are invariably attributable to the metal The effect is known as "caring" and the protuberances are called "ears" Other terms frequently heard are "tips," "scallops," and "corners " It is recognized that the effect is most commonly a result of a directional crystal structure produced by rolling and annealing operations in the manufacture of the metal strip Numerous papers dealing with various aspects of the caring effect have appeared in the literature, those listed in the references' being especially interesting and valuable An investigation of the factors influencing caring of brass cups has been in progress in the laboratories of the American Brass Co for several years, and it was thought desirable to make some of the results generally available in summarized form The present paper discusses many factors that do and do not contribute to ear formation In addition, a section is devoted to methods of minimizing the caring tendency of brass sheet by proper selection of the cold-rolling and annealing schedule by which it is produced In the space available, it is impossible to quote detailed experimental procedures and numerical results However, the authors make no statement that they do not believe to be properly substantiated, either by experimental evidence obtained under laboratory conditions or by experience in the actual production of deep-drawing brass in the brass mill MECHANISM OF EAR FORMATION It must be clearly understood that the formation on cups of symmetrical ears, four or more in number, is attributable solely to the strip metal, and results from the strip having different deformation characteristics in different directions The tools used in the drawing process, or the type and completeness of lubrication of the strip, have nothing to do with the problem of ears, although they do, of course, greatly affect the "drawing quality" of the strip and the general appearance of the cup A single tip may be drawn up on the rim of a cup because of misalignment of the tools, or because the gauge of metal varies from side to side of the strip The two-ear form that sometimes appears is also traceable to gauge variations However, the four-ear and six-ear symmetrical forms that we are concerned with here are caused by factors inherent in the structure of the metal itself

Jan 1, 1942

By Reuel A. Cochrane, Harry H. Angst

The successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. Rock Formations At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally in the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. Jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1943

By Harry H. Angst, Reuel A. Cochrane

The successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. Rock Formations At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally in the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. Jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1943

By W. B. Boggs, J. N. Anderson

An account of the operation of the Noranda smelter covering the period from December, 1927, when the smelter started, until December, 1929, was given in a paper published by the Canadian Institute of Mining and Metallurgy early in 1930.' The object of the present paper is to review matters of interest in the original paper and to describe the present construction and operation of the smelter, with particular reference to the reverberatory-furnace practice. The Noranda smelter was built by Noranda Mines, Ltd., from the designs of A. E. Wheeler, consulting metallurgist of New York, for the reduction of ores and concentrates from the Horne mine and to treat, on a custom basis, ores and concentrates from other mines in the Rouyn district. The smelter is at Noranda, about 330 miles directly north of Toronto. Construction work was started in June, 1926, and copper was first produced in December, 1927. The smelter was built throughout as two duplicate units, each with a rated capacity of 500 tons of ore per day. Operations were started with one unit and after several months it was found that one unit alone could smelt 1000 tons of ore a day. At that time there was only one hoisting shaft, No. 3, and its hoisting capacity and the capacity of the original crushing plant were insufficient to supply ore for the two units at the increased tonnage. Accordingly No. 4 shaft was sunk and a new crushing plant provided to handle the ore hoisted there. Operating two units at capacity also required the installation of two more converters to treat the additional quantity of matte produced. This work was completed in the latter part of November, 1929, and since then both smelter units have been operating continuously. In 1928, a mill to treat 500 tons a day of concentrating ore was completed. Since then the concentrator capacity has been increased twice, and at present 2000 tons a day of ore are being concentrated. The layout of the surface plant of the mine, concentrator and smelter is shown in Fig. 1 and the general plan in Fig. 2. The smelter is shown in more detail in Fig. 3. The original hoisting shaft, No. 3, is now used only for handling men, supplies and waste rock, and the original crushing

Jan 1, 1934

By Maurice Ewing

THE purpose of this paper is to present the results of the application of the earth-resistivity method of subsurface investigation to the problem of locating seams of anthracite coal beneath a mantle of soil and subsoil. Details are given of the successful use of this method in locating the outcrops of anthracite seams in actual prospecting. The presence of the outcrop of an anthracite seam is indicated at points where electrical resistivity tests showed relatively low readings. The reason for this is that in some localities the resistivity of anthracite was found to be about 0.0001 megohm-cm. compared to 1 to 200 megohm-cm. for shales and sandstones. For two reasons it is believed that the data sum-marized in this paper should be of particular interest. In the first place, most of the interpretations of the resistivity survey have been checked by subsequent drilling and some by the removal of the overburden and the exposing of the anthracite seams. It is infrequent that the oppor-tunity for checking results so thoroughly is given. In the second place, the fact that recent commentators1,2,3 on the application of geophysical methods to mining have concluded that direct prospecting for anthracite and other types of coal is not promising makes the good results obtained more significant. So far as the authors can learn, the only previous experiment with electrical methods in the Pennsylvania anthracite field was one made by Sherwin F. Kelly in 1922, when he used the self-potential method at Wilkes-Barre4. The profile he made does not show a very marked correlation with the geologic cross section. Kelly points out that stray currents from electric motors in the mines undoubtedly affected his results, but the experience of the present authors with stray currents from mining machinery suggests the possibility that the potentials measured by Kelly were due almost entirely to this effect.

Jan 1, 1936

By T. A. Rickard

The Cripple Creek district occupies a cluster of foot-hills on the south side of Pike's Peak and is a portion of an extensive, though uneven, plateau which unites the eastern range of the Rocky mountains with the Sangre de Cristo. It is essentially a small volcanic area, of about 20 square miles, amid the granite of the Front range. But though, when regarded as a rich mining district, it may be considered as an isolated area,* yet, geologically, it is, as Whitman Cross has pointed out, only an outlying portion of a much larger volcanic region, which stretches to the south and west, around Silver Cliff and the Rosita hills, forming the picturesque country cut by the deep cañons of the Arkansas river and its tributaries. The mines are situated amid a volcanic complex, consisting of tuffs and breccias which have been penetrated by an extensive system of dikes and other intrusive masses. The prevailing formation is an andesite breccia, which lies upon the worn surface of the granite and fills the deep basin around a volcanic vent. The breccia, since its deposition, has been broken into by several eruptions of phonolite and, later still, by a series of thin dikes of basalt and other allied rocks of a highly basic composition. The successive sedimentary formatione which, elsewhere in Colorado, lie upon the basal granite, are not represented in the district; whatever sediments were laid down before the volcanic period must have been removed by erosion, and there is very little evidence which affords a datum-line whereby the geological age of the volcanic eruptions can be determined. Whit-

Jan 1, 1901

By C. W. Clark, J. H. Schloen

Two papers have been written previously concerning operations at the Montreal East plant of Canadian Copper Refiners Limited. The first one,1 written in 1932, described silver-refinery operations at the time for producing silver and gold bullion from tankhouse anode slimes; the second,2 published in 1933, consisted of a description of the entire plant. Since publication of these papers the refinery has become the world's largest producer of refined selenium. The first selenium was produced in August 1934. Tellurium production on a commercial scale followed in October 1935. This paper will deal with selenium and tellurium production and also with present operations in the silver refinery. Blister cakes from Hudson Bay Mining and Smelting Co., Flin Flon, Manitoba, and commercial anodes from Noranda Mines Limited, Noranda, Quebec, are refined at Montreal East. Both these bullions have unusually high gold, selenium and tellurium content. The average assay of raw slimes produced from domestic and Noranda anodes is about 40 per cent Cu, 3600 oz. per ton Ag, 800 oz. per ton Au, 22 per cent Se and 3.7 per cent Te. EARLY SILVER-REFINERY OPERATIONS From the start of operations in 1931 until July 1934, the raw slimes were oxidize-roasted at 700° F. in a Nichols-Herreshoff furnace, acid¬leached with tankhouse discarded foul electrolyte (20 per cent H2SO4), filtered and charged directly to the doré furnace for refining to doré metal. This is the customary method for treating tankhouse anode slimes but was not suitable at the Montreal East plant because of the high selenium and tellurium content of our slimes. In the acid-leaching process about 50 per cent of the selenium and tellurium in the roasted slimes was dissolved in the electrolyte. These elements were recovered with the copper as a sludge in a small electrolytic

Jan 1, 1938

By Carmine D. &apos, Lemuel Tarshis, Joel Hirschhorn, Antonio

Vapor-deposited nickel films in the thickness range 700 to 4360A were tested in uniaxial tension utilizing a microtester designed specifically for this study. Contrary to the findings of some investigators, a definite thickness-strength relationship was observed below 3000 A with a four-to sevenfold increase in strength over that of bulk nickel. The films were characterized by high elastic strains and little plasticity. On the basis of these and other reported data, it is suggested that the high strength level in metal films is related to the manner in which they are produced. Vapor deposition, owing to its severe quenching effect. is believed to promote the formation of point defects which inhibit dislocation movement. IN recent years it has been reported that metals, when in the form of thin films, exhibit extraordinarily high strengths. The data published to date have been primarily concerned with silver and gold because of the ease with which these metals can be vapor-deposited and their high resistance to surface oxidation. Previous investigations into the mechanical strength of thin films has uncovered an apparent dichotomy of view on film behavior. Beams and his co-workers have reported a definite dependence of strength on film thickness. Other workers,"-'6 however, in separate studies on the strength of poly crystalline and single-crystal films have found no such thickness-strength relationship. The study of thin-film strength is extremely difficult because of the many variables associated with film preparation, handling, and testing. Moreover, the manner of test employed by different investigators has varied quite radically, ranging from simple uniaxial-tension to biaxial-bulge testing. The work reported herein was conducted in order to determine the mechanical behavior of a structural metal when in the form of a vacuum-deposited thin film and to gain some insight into the reasons for the high strengths exhibited by metals having such a con- figuration. In this study a method of test was chosen which would yield results which are easily interpreted and lend themselves to comparison with properties of the same material in bulk form. Moreover, specimen-preparation parameters and film-handling techniques are set forth so that other investigators can properly compare their findings with ours. EXPERIMENTAL PROCEDURES A) Film Preparation. Vacuum deposition was performed in an 18 by 30 in. bell jar using a standard New York Air Brake Co. vacuum station with a 6-in. oil-diffusion pump. Before evaporation the system was pumped to a pressure of less than 2 x 10"5 torr. A shield was employed to protect the substrates from the emission of contaminants during the critical melting and outgassing of the evaporant. The source consisted of from one to six filaments (0.020 in. diam). The length of each filament was about 5 in. and was placed 6 to 8 1/2 in. from the substrate in such a manner that the substrate face was at 90 deg incidence with respect to the evaporant beam. The temperature of the source was 2000"~ during evaporation. The films were deposited onto a substrate arrangement which was composed of four basic components, that is: 1) a 3 by 1 in. glass slide; 2) a 22-mm sq micro cover glass on 1); 3) a 22 by 50 mm micro cover glass coated with collodion on 1); and 4) a stainless-steel sheet mask containing twelve rectangular openings of 1-mm and 2-mm widths and lengths of 5 mm laid over 3). Thus, test specimens of 1-mm and 2-mm widths are deposited onto a collodion substrate which precludes epitaxial effects in the specirnens. 17-le The rectangular cover glass and square cover glass were positioned in such a manner that a strip of film would be evaporated along the length and across the width of the large glass slide. This boundary of evaporated film was used to determine the film thickness by multiple-beam interferometry. The square cover glass was used for X-ray and chemical analyses. Thickness of the deposits was varied by changing the number of filaments used (one to six). The duration of evaporation was 30 sec for each filamgnt which resulted in a deposition rate of 8 to 20A per sec. Evaporations were all performed at room temperature; however, radiant heat from the source raised the substrate temperature to 40" to 60°C. All substrates were cleaned by ultrasonic agitation in a solution of spectranalyzed isopropyl alcohol. Collodion was deposited on the micro cover glass by immersion in solution of collodion in amyl acetate. B) Thickness Control and Measurement. Film

Jan 1, 1963

By Thomas Watson

INTRODUCTION THE users of barite in the United States derive their supply partly from the domestic production and partly from the imports from foreign countries. According to the Mineral Resource division of the U. S. Geological Survey, the domestic production of barite in 1913 was 45,298 short tons, valued at $156,275, or $3.45 a ton, and the imports of crude barite were 35,840 short tons, valued at $61,409, or $1.71 a ton. These figures clearly show a decided advantage in cost of the foreign over the domestic barite to users in the United States. The difference in cost is the only advantage to the consumer of foreign barite, for there are large reserves of the mineral in the United States of good grade. The production of many of the operating mines is capable of decided increase, and it is believed that the operating mines together with the large reserves of undeveloped deposits of barite are entirely adequate to meet the demands of the users in the United States. Deposits of barite are known in California, Idaho, Nevada, and Alaska, but most of them are undeveloped because there is, apparently, no market for the .material in that region. The domestic production is derived from Missouri and the Appalachian States, the greater part being obtained from Missouri. Following the outbreak of war in Europe many users of foreign barite in the United States have been forced to seek their supplies at home. It seems opportune at this time, therefore, that a general review be given of the barite industry in the Appalachian States, one of the two areas from which the domestic supply of the mineral is derived, and that attention be directed to the undeveloped deposits in the region. Briefly, then, this paper reviews the barite industry in the Appalachian States, and describes the occurrence, preparation, and uses of the mineral.

Jan 2, 1915

By Samuel Taylor

IF I LIVE another fourteen months and am still con-nected with the coal industry, I shall then have com-pleted a half century with it. Since May, 1874, when .I first entered the bituminous workings as a miner, I think I have held almost every position connected with a mine except possibly that of mule driver, for which I was unfitted by reason of my religious upbringing. We are all agreed, at least I have not heard it contra-dicted, that there is serious over-production in the bituminous industry. This has come about in various ways and is easily explained. During the Fuel Admin-istration, I recall making an estimate of the possible output of the bituminous mines of the country provided they were given a full force of men and a full-car supply; my estimate was a little over a billion tons a year. A few months ago, the late Francis H. Peabody, of Chicago, made a practically identical estimate. If, however, both of these conditions should happen con-currently, there would very soon be no market for the coal, and many of the mines would close down. Even today, if 10 per cent. more cars were furnished, to the bituminous mines, market prices would drop very seriously.

Jan 4, 1923

By Charles T. Holland

In connection with the problems of bumps in coal mines, much has been written concerning the manner in which roof action and methods of mining enter into the pressure effects observed but little has been written upon the relationship between the physical properties of coal and associated rocks and the cause of bumps. The question of the strength of bituminous coal, of its elasticity, and the energy it can absorb and store has been neglected to a considerable extent in connection with this problem. It is generally agreed that one of the necessary conditions for bumps is a strong coal.' Therefore, since the strength of coal is an important factor, a study of this property should be made. several investigators have conducted laboratory experiments upon the strength of coal, using small cubical or rectangular test pieces. An attempt will not be made to go into all of these investigations, but they are briefly summarized in Table I. Experiments of the U. S. Bureau of Mines and of Lawall and Holland (pp. 27 and 34 of ref. 9), however, indicate that regardless of whether the coal is a soft and weak semihituminous (Pocahontas No 3) or a hard and strong bituminous (Stockton) coal, the maximum ultimate unit stress developed in laboratory tests is higher in small cubes than in larger cubes of the Same coal.

Jan 1, 1942

By Charles T. Holland

In connection with the problems of bumps in coal mines, much has been written concerning the manner in which roof action and methods of mining enter into the pressure effects observed but little has been written upon the relationship between the physical properties of coal and associated rocks and the cause of bumps. The question of the strength of bituminous coal, of its elasticity, and the energy it can absorb and store has been neglected to a considerable extent in connection with this problem. It is generally agreed that one of the necessary conditions for bumps is a strong coal.' Therefore, since the strength of coal is an important factor, a study of this property should be made. several investigators have conducted laboratory experiments upon the strength of coal, using small cubical or rectangular test pieces. An attempt will not be made to go into all of these investigations, but they are briefly summarized in Table I. Experiments of the U. S. Bureau of Mines and of Lawall and Holland (pp. 27 and 34 of ref. 9), however, indicate that regardless of whether the coal is a soft and weak semihituminous (Pocahontas No 3) or a hard and strong bituminous (Stockton) coal, the maximum ultimate unit stress developed in laboratory tests is higher in small cubes than in larger cubes of the Same coal.

Jan 1, 1942

By H. I-Lieh Huang, O. D. Sherby, J. E. Dorn

RECENT investigations1-4 have suggested that the total plastic strain, C, for high temperature creep under a given stress can be correlated by means of a temperature-compensated time, te- where t is the duration of test, e is the base of natural logarithms, aH is the activation energy for creep, R is the gas constant, and T is the absolute temperature. A typical set of data on which this deduction was based is given in Fig. la. Inasmuch as the e-in t curves for the various temperatures are identical except for their displacement along the In t axis where f and are appropriate functions. If the increase in creep rate with an increase in temperature is exclusively ascribable to a single process involv- ing thermal activation, (T) should equal RT and therefore it = constant [2] where ?= te Assuming the validity of this relationship, ? = ?2 at the same strain, or where the subscripts refer to two alternate test conditions.

Jan 1, 1957

By Theodore B. Comstock

The existing topographical features of the United States present many points of interest to the student of dynamical geology, but there is, perhaps, no subject which offers a more promising field for investigation than the relations between the geological structure and the mineralogical characteristics of the principal mining districts. There are seven prominent culminating points in the relief of North America, each one of which can be used as a type of the physical features of all the others. Again, if we divide these seven elevated districts into two sets, we shall discover a still more striking parallelism between the individual members of each group. But the most remarkable revelation is the fact that each one of these points is more or less closely the centre of an area of economically important mineral resources. It is interesting to note in this connection that six of these mineral tracts lie mainly within the borders of the United States, three of them being almost wholly in our territory. For

Jan 1, 1883