Search Documents

By H. B. Hunter, F. G. Stone, F. J. Dunkerley

Introduction and Literature Survey This is the second in a series of papers coming from this laboratory on the correlation of the low temperature tensile properties of tin-binary alloys with microstructure. These engineering data and those of the previous paper1 were obtained as the initial part of a long-range program to determine the changes in the fundamental mechanical properties accompanying the beta to alpha phase change in tin and its binary alloys below 13.2°C. Since it appears now that the more fundamental studies will be delayed,* and since no summary of the low temperature properties of these tin-base white bearing alloys was found in the literature, it was decided to publish all the engineering data thus far obtained. Accordingly, the tensile properties of thirteen binary alloys containing from 0.1 to 60 pet cadmium and 0.1 to 10.43 pet antimony measured at six temperatures from —196 to +23°C are presented here and their variations rationalized in terms of microstructure. A literature search showed that these systems had not been investigated at low temperatures, although both the tin-cadmium and tin-antimony2,3,4,5 and the tin-rich corner of the ternary system67 have been studied at room temperature. Hanson and Pell-Wal-pole5 and Homer and Plummer4 determined the tensile properties of alloys containing from 0 to 10 pet cadmium. The same authors3 determined the tensile strength and elongation in the tin-antimony system from 2 to 18 pet antimony at room temperature while Pell-Walpole et al.6,7 studied the properties of high tin and tin-antimony-cadmium alloys. Since there were many variables besides composition in these tests, it was difficult to make a valid comparison with the room temperature data of the present study, but in general the tensile strength and ductility values are in reasonable agreement. Pell-Walpole2 also determined the effect of grain size on the tensile strength of pure tin and 1 pet alloys of both antimony and cadmium. The true maximum stress was found to decrease exponentially as the number of grains in the cross-section increased. This effect of grain size was strikingly revealed in the present work, as indicated in a later section. Hanson and Pell-Walpole8 placed the solid solubility limit of antimony in tin at 3.5 pet at 20°C, increasing to 4 pet at 190°C, and then sharply increasing to 10.3 pet at 246°C (the latter being a peritectic point). Their results are in disagreement with those of previous investigators,9 and the discrepancy seems to lie in the micro-graphic observation of the second phase

Jan 1, 1950

By D. W. Frommer, M. M. Fine

Mineral dressing research showed that iron concentrates of commercial quality could be produced from the Pea Ridge deposit near Sullivan, Mo. Magnetic separation and flotation, on a laboratory scale, yielded concentrates ranging from 60.0 to 71.4 pet Fe at recoveries of 89.9 to 97.6 pct. Early in 1957 St. Joseph Lead Co. announced discovery of three new centers of iron ore deposition in east central Missouri.' The discovery resulted from exploratory drilling in the vicinity of a magnetic anomaly or high. A deep hole, drilled into the Pre-Cambrian porphyry to determine the cause of anomaly, penetrated a magnetite-rich deposit.' The magnetic surveys that revealed the anomalies were begun by the Missouri Geological Survey in 1929 and were continued into the 1930's.3 At that time an area in Crawford County known as the Bourbon magnetic high was located. A second anomaly, similar in size and intensity, was discovered about six miles to the northeast in Franklin County in the vicinity of Sullivan. This area was not studied in detail until the early 1940's. To determine the cause of the anomalies, the USBM drilled four holes at the Bourbon site in 1943-1944.4 The most productive hole penetrated four mineralized zones having a total thickness of 127.5 ft. These zones contained magnetite in rhyo-lite porphyry at depths between 1600 and 2000 ft. Additional iron ore below 2000 ft was considered a possibility at the time. Some years later, the USGS, Missouri Geological Survey, St. Joseph Lead Co., and others cooperated in sponsoring an aeromagnetic survey of the Bourbon-Sullivan area which resulted in discovery of a third high, about eight miles distant at Pea Ridge. This deposit, with an estimated reserve of 50 to 100 million tons of iron ore, is considered the main find, although other orebodies in the same general area are of definite interest.' When this discovery was announced, St. Joseph Lead also revealed plans to exploit the deposit jointly with Bethlehem Steel Co. A new corporation, Meramec Mining Co., was established, and 1962 was set as the target date for completing physical plant.2 Annual production goals of 2 million tons of beneficiated and pelletized iron ore were proposed. Preparation of the site for shaft sinking was begun in June 1957. Orebody and Character of Samples: Drilling to date has established the Pea Ridge orebody as a crescent-shaped pipe about 300 ft wide. Some drillholes were bottomed at 2800 ft in very good iron ore.6 he orebody is predominantly magnetite, although hematite and a mixture of hematite and magnetite occur in the upper areas and peripheral walls. Drillhole cores representing ore from different areas and depths of mineralization were grouped into composites for testing. These composites consisted of: 1) medium grade mixed hematite and magnetite, 2) high grade mixed hematite and magnetite, and 3) high grade magnetite. The medium grade ore came from three holes with depths of i350 to 1900 ft. The high grade mixed hematite and magnetite cores came from the 1790 to 2812-ft interval of one hole. Partial chemical analyses of the three samples, given in Table 1, reveal that all are excessively high in phosphorus and sulfur, and sample 1 is

Jan 1, 1960

By WILLIAM WATERS

L HISTORY. THE Pierrefitte mines, situated in the South of France, in the district of the Hautes-Pyrenees, owe their name to the fact that the first mining operations of any extent, and of comparatively recent date, were carried out in the neighborhood of the vil¬lage of Pierrefitte, which is a branch terminus of the Midi railway. The Pierrefitte mines, however, embrace a wide extent of country and several different concessions, on most of which comparatively little exploration-work has been done. The portion of the property presently to be described is a zone running roughly E-W., over a distance of about 5 miles from the valley of Cauterets to the valley of Estaing, the ridge dividing these valleys being a spur of the main chain of the Pyrenees, and running more or less at right angles to it. According to local tradition, which various indications tend to confirm, these mines are of ancient date, the first workings being attributed to the Romans, who are supposed to have sought not only the lead but also the silver which is contained in the ore. Old slags have been found in the neighborhood which might well have been produced from the cupellation of lead-ores. These old workings, while of considerable extent at times, do not seem to have extended beyond a depth of 100 ft., even this depth being somewhat exceptional. The old notarial records of the district show that mines were known to exist, and that they were even worked, in the sixteenth century, but since the mines were abandoned (by the Romans or others) considerably prior to this period, very little

Nov 1, 1908

By R. W. Hertzberg, F. D. Lemkey, J. A. Ford

The effect oj unidirectional solidification upon the microstructural, crystallographic and mechanical characteristics of high -purity A1-A13Ni eutectic a1loy specimens has been investigated. varying the growth rate caused the morphology of the Al3Ni phase to gradually change from platelets to rods. In addition, the effect of increasing the rate of planar liquid-solid interlace movement is to decrease the Al3Ni rod diameter and inter-rod spacing. The platelets and rods grow approxinlately parallel to each other and are aligned in a faulted substructure. A single unique crystallographic relationship hetween the A1 and ASNi phases was found and may he descrihed as : interface {001} Al3Ni {331} Al and growth direction <010>Al3Ni || <110> Al The platelet interlace and the aligned rows of rods are both uniquely defined by the above statements. Alignment of the Al3Ni phase by unidirectional solidification has given rise to a threefold increase in strength over that exhibited by specimens with an as-cast microstructure. These results illustrate the possible use of this eutectic alloy as a zohisker -reinforced structure. It has been demonstrated by Winegard et al.,1 Kraft and Albrighht,2 Chilton and winegard,3 Chad-wick,4 Yue,5 Tiller,6 and others that a planar liquid-solid interface may be established in binary eutectic alloys by proper control of heat flow during the solidification process. The unidirectional movement of such an interface results in a eutectic mi-crostructure consisting of an essentially parallel array of the two phases over an entire ingot. Two dominant phase micromorphologies have been produced using this technique: that of substantially parallel alternating lamellae of each phase or long thin parallel rods of one phase imbedded in a continuous matrix of the other phase. While not all eutectics can be controlled in this manner, it has been shown that a "normal" eutectic may, under properly controlled conditions of purity, liquid and solid thermal gradients, and solidification rate, be forced to solidify with essentially parallel phase particles. Kraft and Albright2 have demonstrated that, when the growth rate is too rapid or when the thermal gradient in the liquid at the growing interface is too low, a layer of constitutionally supercooled liquid, formed by impurity build-up, will stabilize a cellular rather than a planar interface. The unidirectional movement of the cellular interface forms the macrostructure of eutectic colonies.7 Chilton,3 Chadwick,4 and Tiller,&apos; studying eutectics of zone-refined Pb-Sn, A1-CuAl2, Zn-Sn, and Cd-Zn systems, noted that in the absence of impurities a planar interface is stabilized even when rapidly solidified. Although it is generally agreed that impurities break down a planar interface to form the eutectic-colony macrostructure, at present the origin of the varying micromorphologies (i.c., plates or rods) in a given normal eutectic alloy is not completely understood. Tiller8 has predicted that the micromor-phology produced may be dependent on solidification rate (i.e., at fast rates a rodlike structure is preferred whereas at slow rates a lamellar structure should form), and also suggested that rod formation may be favored at large phase-volume ratios. yue5 has experimentally verified Tiller&apos;s prediction in the eutectic Mg-Mg17Al12 by observing a lamellae-to-rod transition with increasing growth rate where the phase-volume ratio was approximately 2.3:1. However, Hunt and chilton9 more recently unidirec-tionally solidified over a wide range of growth velocities six different eutectic systems with phase-volume ratios between 12:l and 2.7:1 and observed no lamellae-to-rod transition. chadwickl0 has proposed that the change in micromorphology in some eutectic alloys is due entirely to the presence of impurities and further states that the lamellar structure is the characteristic structure of pure eutectic alloys even when the phase-volume ratio is as great as 12:l. Kraft11,12 has shown that the parallel lamellae in certain eutectic alloys assume a unique crystallographic relationship during unidirectional growth. This preferred crystallography may be developed

Jan 1, 1965

Jan 1, 1951

Jan 1, 1951

By H. E. Cline

Mechanical properties of the eutectic between CoAl and cobalt were measured over a range of- temnperatures and strain rates for a variety of microstructures produced by directional solidification and by thermo-mechanical processing. Directional solidification led to rodlike, lamellar, and irregular microstructures. The unusually high volume fraction of the cobalt-rich rods and the lurge spacing of the rods were explained by the phase diagram. The hot-worked structure consisted of fibers of COAL in a cobalt-rich matrix. The roonl- tevlperature strength of the uvrought material increased with decreasing grain size but the 1000°C strength decreased with decreasing pain size. At high temperatures the directionally solidified tnaterial was stronger and less strain-rate-sensitice than the hot-rolled material. The fine-grained hot-worked ma-terial became superplastic at high temperatures, with tensile elongations greater than 850 pct, while at root temperature this material was ductile and impact-resistant because of the ductile matrix. Fracture occurred in the directionally solidified material at elevated temperatures by inter phase separation and at roorn temperature by cracks in the intermetallic phase. Growth of these cracks was impeded by the ductile cobalt-rich phase. It was found that the CoAl intermetallic remains ordered at elevated temperatures. DIRECTIONAL solidification of eutectic alloys has been used to produce structures consisting of parallel rods or lamellae. Although the spacing of the phases depends on the growth rate, it has been observed to be of the order of 1 µ in many eutectics. A strong intermetallic phase has been used to reinforce a ductile matrix in the rod eutectic A1-Al3Ni and the lamellar eutectic Al-Al2cu.1 The microstructure of the eutectics A1-A13Ni and A1-A12Cu remained aligned after samples of these alloys were exposed to temperatures just below their melting points for long times. Stability of the microstructure at elevated temperatures makes directionally solidified eutectics a candidate for high-temperature applications. Recently Thompson4 has developed the Ni-NiMo eutectic containing 40 pct NiMo lamellae, giving a tensile strength superior to nickel-base superalloys. Unfortunately, this eutectic oxidizes rapidly at elevated temperatures. By mechanically processing a two-phase structure, one may reach strengths as high as 700,000 psi, as demonstrated by drawn pearlite.5 In this case the strengthening mechanism was thought to be related to the fine substructure formed during deformation.5 However, a heavily worked structure may recrystallize and coarsen at elevated temperatures. Some worked eutectics such as Al-Al2Cu,6 Pb-Sn,7 and Sn-Bi7 have shown unusually large elongations in tension when tested at elevated temperatures. This phenomenon of large extension, called "superplasticity", was related to the fine grain size of wrought two-phase alloys at elevated temperatures. A mode of deformation of "superplastic" material has been shown to be grain boundary sliding,&apos; which has also been observed during creep of polycrystalline materials.9 The Co-A1 system was chosen for this investigation after examining the phase diagrams of binary eutectics." The high melting point of 1400°C, the aluminum content which was expected to give oxidation resistance, and the properties of the intermetallic CoAl were the chief factors influencing this choice. This eutectic consists of a mixture of the intermetallic CoAl and a cobalt-rich solid solution. The intermetallic CoAl has a large range of solubility and a CsCl structure." From the similarity between CoAl and NiAl one would expect CoAl to be ordered at elevated temperatures; however, specific heat measurements" show a transition at 800°C. West-brookL2 has measured the hot hardness of CoAl and found a rapid decrease in hardness above 600°C. The tensile properties and stress rupture properties of as-cast CoAl-Co eutectic were measured by Ashbrook and wallace13 who report a room-temperature tensile elongation of less than 1 pct. I) EXPERIMENTAL A) Sample Preparation. Experimental materials were prepared by directional solidification, by hot working, and by powder processing. The starting materials were electrolytic 99.9 pct pure cobalt and 99.99 pct pure aluminum. 1) Directional Solidification. A vertical Bridgman apparatus heated by induction was used to directionally solidify cylindrical ingots $ in. in diam and 5 in. long. The apparatus was first evacuated and then an argon atmosphere was introduced to retard evaporation. The ingots were contained in an alumina crucible inside a graphite susceptor that rested on a movable water-cooled base. The base was lowered out of the induction coil at a constant rate. Eight of the ingots were solidified using a drive rate of 2.5 cm per hr, two of the ingots at 1.2 cm per hr, and one ingot at 10 cm per hr. The eutectic composition Co 10 wt pct A1 was used in all but one ingot which had the composition of the stoichiometric CoAl intermetallic, Co 32 wt pct Al. 2) Mechanical Processing. At 1000°C the eutectic Co 10 wt pct A1 is a mixture of an intermetallic phase, Co 21 wt pct Al, and a cobalt-rich phase, Co 5 wt pct Al.10 These phases differ from the stoichiometric CO 32 wt pct A1 and pure cobalt because of the large solubility of this eutectic at elevated temperatures." Four rectangular slab ingots, 4 by 1 by 12 in. high, of Co 10 wt pct Al, Co 5 wt pct Al, Co 21 wt pct Al, and Co 32 wt pct A1 were cast for hot rolling. The cobalt was first vacuum-melted, H2-treated for 20 min,

Jan 1, 1968

By R. A. Stauffer

The chief ore of lithium is spodumene, a lithium-aluminum silicate containing up to 3 pct lithium. The preparation of lithium salts from spodumene is costly because of the low concentration of the metal and the difficulty of separating it from the other alkali metals present. Dr. Kroll&apos;s and Dr. Schlecten&apos;s recent paper1 has reviewed various methods proposed for preparation of lithium. It will be seen from this paper that the methods proposed to date have required one or another of the lithium salts as a raw material. The high cost of these salts has been the chief item of expense in the lithium metal produced. This situation has made it interesting to investigate the possibility of producing the metal directly from spodumene. When spodumene is calcined at 1000ºC in the presence of lime, lithium oxide is replaced in the ore as is evidenced by the fact that it may be leached from the reaction mixture with water.2 Free energy calculations suggested that lithium oxide might be reduced with aluminum or silicon and the lithium produced distilled from the reaction mixture by heating-to about 1000ºC in a vacuum. These facts taken together suggested that it might be possible to prepare lithium metal directly from spodumene by heating a mixture of the ore, lime, and a suitable reducing agent in vacuum and distilling off the lithium metal as formed. The Replacement of Li2O in Spodumene A series of experiments were undertaken to determine the ratio of lime to spodumene necessary to free substantially all the lithium oxide Present in the Ore. The spodumene used in these experiments was supplied by Foote Mineral Co. in the form of powder of about 200 mesh&apos; Analysis of the spodumene was as follows: PCT SiO2......................... 62.7 Al2O3........................ 29.9 Li2o......................... 4.9 Na2O........................ 0.89 CaO......................... 0.75 MgO........................ 0.49 K2O......................... 0.44 Lime (cp —200 mesh) was added in various ratios to spodumene and thoroughly mixed in a ball mill. Two hundred gram samples of spodumene-lime mixtures were charged loosely in fireclay crucibles and held at 1000ºC in a gas-fired furnace for 5 hrs. The product in each case was ground to pass 140 mesh and then placed in a thimble in a soxhlet extractor. Extraction with water was carried on for 6 hrs. After this period the extract was reduced in volume by evaporation in order to precipitate dissolved lime and was then filtered and titrated with 1/4 normal hydrochloric acid. After correcting for residual calcium oxide in solution, the alkali present was calculated as lithium oxide. The results of these experiments are shown in Table I and Fig I. At lime-spodumene ratios less than 1.5, the products were invariably fused. At the ratio of 1.5 and above, the product was loosely sintered with little evidence of fusion. When the ratio of lime to spodumene was three, replacement of alkali oxides in the

Jan 1, 1949

Lake Superior Meeting . PAGE Gathmann, Emil.-Casting and Molding Steel Ingots. Discussed by J. W. Richards.. 2 McCaffery, R. S.-The Acid Bessemer Process. Discussed by Bradley Stoughton, J. W. Richards 3 Elliott, S. R.-Athens System of Mining. Discussed by F. W. Sperr, Lucien Eaton 4 Mercer, H. T. and Paulson, A. C.-Handling and Treatment of Rock-drill Steel at Copper Range Mines. Discussed by Harrison Souder, H. T. Mercer, W. H. Schacht, C. M. Haight 5 Hayden, J. E. and Eaton, Lucien.-Building Reinforced-concrete Shaft Houses. Discussed by William Kelly, T. L. Condron, Lucien Eaton 7 Eaton, Lucien.-Mechanical Ventilation at Lake Mine. Discussed by C. A. Mitke 8 Schacht, W. H.-Steam Regenerators Reduce Coal Consumption. Discussed by 0. P. Hood, W. H. Schacht ? 9 Linton, Robert.-Standardizing at North Butte Mining Co. Discussed by Grant H. Tod, C. A. Mitke 10 Smith, H. DeWitt and Sirdevan, W. H.-Mining Methods and Costs at United Verde Mine. Discussed by C. A. Mitke 12 Davy, Myron A.-Reflecting Microscope for the Mining Engineer. Discussed by C. P. Berkey, W. A. Rukeyser 14 , Norden, J. A. and Willson, A. R.-Hoisting Equipment at Utah-Apex Mining Co. Discussed by E. M. Norris 17 Aldrich, H. R.-The Dip Needle in Stratigraphy. Discussed by H. R. Aldrich, W. 0. Hotchkiss, Carl Zapffe, E. A. Kronquist 18

Jan 1, 1921

[59H1-Water Law and Its Significance to the Mining Industry by Wells A Hutchins 59H2-Relation of Land Subsidence to Groundwater Withdrawals in the Upper Gulf Coast Region, Texas by Leonard A Wood and A G Winslow 59F3-Hydraulic Mining of Gilsonite and Its Application to Coal Mining by J H Baker 59H4-Recovery of Phosphates by In Situ Fluid Mining by Sylvain J Pirson 59F5-Coal Cleaning Plant Design for Minimum Operating Labor by Wm M Bertholf and John D Price 59F6-Coke Combustibility A Neglected Characteristic by J D Price 59B7-Union Carbide&apos;s Uranium Operation at Maybell, Colorado by K W Lentz and F T Temple 59H8-A Rapid Method for Estimating Alumina in Feldspathic Sands by Hugh H Bein 59H9-Water Laws as Related to Dredging in Idaho by Robert A Lothrop, Richard B Porter, and Robert P Porter 58B19-Separation and Washing of Alumina Process Residue by Morton Handelman 59B11-Feed Preparation and Froth Modification for Fatty Acid Flotation by Carl C Martin and Burt C Mariacher 59B12-Design Requirements for Tailing Disposal in the Southwest by E Vern Given 59B13-Semi-Dome Shaped Buildings for Bulk Storage by Edward E Ives and William L Payne]

Jan 1, 1961

Jan 1, 1900

THERE are three chief production zones of tungsten ore in China. In the Province of Kiangsi mines are located at Kanchow, East River, and West River. Their combined production is understood to amount to 300 to 350 tons of ore per month, and their original exportation is made through the port of Kiukiang, largely to Shanghai. The second zone is in Kwangtung Province, the mines there being at Tayulin. Produc-tion reaches about 200 tons per month and cargo is gen-erally exported through the port of Hong Kong. In the Province of Hunan approximately 25 tons of ore are produced monthly in the mines at Ton-on. Tungsten ore from Kiangsi and Kwangtung Prov-inces is generally about 70 per cent WO, (tungstic acid), while that from Hunan is of lower quality, run-ning about 65 per cent WO3. Kiangsi ore is received from the mines in 100-1b. and Hunan in 224-lb. gunny sacks. No repacking is done except as it is made neces-sary by the condition of the sacks. Kiangsi Province contains the Chinese districts pro-ducing the largest amount of salable wolframite or tungsten. Many districts west and south of Kiangsi have been found to have wolframite deposits.-Com-merce Reports.

Jan 1, 1928

By Otto Henry

THE purpose of this investigation was to determine the equilibrium diagram of the lithium-magnesium pair as a first step in studying the possible usefulness of these alloys as ultra-light structural materials. REVIEW OF THE LITERATURE The behavior of lithium towards magnesium was first investigated by Masing and Tammann.(I)? In order to prevent oxidation the alloys were made in iron tubes under an atmosphere of hydrogen; temperatures were measured with a glass-protected thermocouple. These investigators found that lithium and magnesium form two series of solid solutions separated by a miscibility gap between 85 and 95 per cent magnesium; that the alloys with 81 and 95 per cent magnesium showed a homogeneous structure under microscopic examination, while the alloy with 89 per cent magnesium contained two distinguishable crystallites; that the curve indicating the beginning of crystallization rises from the melting point of lithium to that of magnesium; and that no compounds of lithium and magnesium are formed. The equilibrium diagram was not plotted because no definite data were obtained for determining the solidus and the posi-tion of the miscibility gap in the solid state. The difficulties encountered in this investigation were: (1) that it was necessary to heat them as high as the melting point of magnesium in order to obtain homogeneous melts; at such temperatures the alloys attacked the glass protecting the thermo-couple; and (2) that at temperatures above 400° C. the lithium united

Jan 1, 1934

MEMBERS-QUALIFICATIONS AND ELECTION SEC. 1. The membership of the Institute shall comprise seven classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members; 7. Junior Foreign Affiliates. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall he entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years&apos; employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which be must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members. SEC. 3. Honorary Members: Each candidate for Honorary Membership must be recommended by at least ten Members and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of the Directors present; provided, however, that the number of Honorary Members shall at no time exceed twenty. Such election shall automatically act as a transfer of such member from any other class of membership to which be may belong.

Jan 1, 1938

By C. G. Goetzel

Until recently porous bronzes have found many applications for self-lubricating bearings in the automotive, electrical, household appliance and general machine industries. The bulk of an annual production of several million pounds of copper powder had gone into the manufacture of these articles, of which by now more than a billion are in service. However, the war has brought severe curtailment of these bearings because of the scarcity of the two main constituents, copper and tin. The development of substitute materials of equal or superior properties has led to a large-scale replacement by products made from iron powder. In spite of the diminished interest in powdered copper-tin alloys caused by this trend, it was believed worth while to investigate some mechanical properties of these materials as a reference base for substitutes. In addition, experiments using the hot-press method were incorporated to investigate possibilities of saving vital equipment or opening new fields of applications. It must be assumed that by this time the powder metallurgy process of making porous bronzes, a development that found its first industrial applications more than 10 years ago, is well known in engineering. The patent literature and bibliography is volu- minous, most publications referring to porous, self-lubricating bronzes, containing about 10 per cent tin and I to 5 per cent graphite, with porosities in the range of 25 to 35 per cent.l-7 The excellent antifriction properties of these bearings, caused by the uniform impregnation with oil, are dependent on the interconnection of the pores and the uniform distribution of the graphite inclusions. The sintering mechanism of porous bronze, with its structural changes during the transformation of the metal powder into the sintered bearing has been shown in colored photomicrographs by Hall.* Diffusion between copper and tin was found to begin within one minute, when tin-rich transitory phases were formed. After 25 min. a homogeneous matrix of alpha was reached for an alloy containing 9.5 per cent tin and 6 per cent graphite. Price, Williams and Garrand,9 studying certain metal powder combinations in which sintering is accompanied by the cementing action of a liquid phase, including a 90-10 bronze sintered at 925°C., have found that if the treatment is carried out within the liquidus and solidus temperature range of the system, a peculiar process of alternate solution and precipitation occurs. The particles of the major solid constituent are dissolved in the minor liquid phase, but thereafter are reprecipi-tated on certain nuclei, which develop into large grains, usually rounded.

Jan 1, 1945

By A. L. Mular

lnput energy-size modulus relation at small reduc-tion ratios is expressed by Et = (M, -Mt) k;. In some cases 13 is close to Schuhmann&apos;s distribution modulus a in value. Experimental results in conjunc-tion with the equation demonstrate the fact that energy input which produced fracture is not expended on unbroken starting material inside the mill at any time. Recently, schuhmann1 derived the Charles equation2 using the postulate that complex com-minution operations can be considered as a summa- tion of many comminution events. The fragments resulting from each event are assumed to follow the Gaudin-Schuhmamn distribution. In his derivation, Schuhmann implies that the size distribution of the total mass of a material is determined by the fraction of that mass actually subjected to comminution. Consider a feed to contain a volume, Vo, of uni- formly sized homogeneous material. After t seconds of grinding, let the volume of broken material be Vo - Vt where Vt is the volume of starting material not yet broken. The size distribution of the broken material is given by: where V is the cumulative volume less than size X, and k, is the size modulus of the broken material at time t. The distribution for the total volume at this

Jan 1, 1962

By Clarence Zener

THE internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites,4,5 localized weak regions introduced by cold-working,6,7 grain boundaries and possibly twinning planes.8,9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation. was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, ½ in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff.10 EXPERIMENTAL METHOD The experimental method used has previously been described in Institute papers.5,6,9 The measure of internal friction adopted here, 1/Q, is (1/p) X the logarithmic decrement, a measure used by some writers, and is also (1/2p) X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the funda¬mental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. EXPERIMENTAL RESULTS The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°C. As shown in Fig. 1, the internal friction increased by only a factor of 2 from room temperature to 300°C., then by a factor of l00 during the next 100° interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction e~H/RT [I]

Jan 1, 1942

By Ernest F. Burchard

PAGE. I. Introduction,........... 75 II. Outline of the Geology......... 76 1. Stratigraphy............ 76 A. Clinton Formation........ 77 2. Structure...........82 3. The Ore..........85 A. Character............ 85 B. Geographic Distribution....88 III. Local Descriptions........... 88 1. Birmingham District.......... 88 A. Topography and Its Relation to Industrial Development... 88 H. Distribution and Structure of Formations.... 89 C. Divisions of the Birmingham District. 95 Division A (Description of the Ore-Beds), . 95 Division B.........105 Division C.......... 106 Division D,..107 Division E,...........108 Division F........ 111 Division C.......... 112 D. Mining .Development.... 113 2. Northeast Alabama........114 IV. Possible Origin oF the Ore......... 119 V. Relation of Origin to Quality and Extent of Ore... 122 VI. Estimates of Ore-Reserves,......... 125 1. Method of Making Estimates......... 125 2. Data and Results....126 VII. Production and Consumption oF IRon-ORe,.... 132 I. Introduction. Brief and interrupted studies of the Alabama Clinton iron-ores have been made within the last four years by members of the IT. S. Geological Survey. Reports on the progress of this

Jan 1, 1910

By Edgar M. Dunn

Part I. Determination oF Gases in Smelter Flues. General considerations. Regular methods for carbon monoxide, oxygen, nitrogen, moisture. Sulphur oxides-—Methods of Lunge and Hempel tried, and either modified or discarded, with reasons therefor. Gravimetric method developed at Anaconda. Description of apparatus used. Brief notes on Richter and Hawley methods for the direct cietermination of sulphur trioxide. Carbon dioxide, with complete notes on same. Arsenic trioxide. Table of percentages of flue gas constituents found at a Western smelter. Some final notations as to the value of flue gas analysis, in connection with an intelligent log of furnace operations. Part II. Notes on the Determination oF Dust Losses at the Washoe Reduction Works, Anaconda, Mont. Discussion of problem, with description of flue system. Various places and methods for determinations of velocity. Instruments used. Procedure in making determinations for velocity. Soundings of cross-section for depths of dust. Calculation of velocities and areas. Daily volume of gas, and plant operations during tests. Place for dust determinations. Apparatus and methods of &apos;sampling. Results obtained, with table of daily amount of dust losses. Analysis of dusts for values, from various sampling stations. Complete analysis of composite sample of stack emanation. Last analysis totaled to show form in which present. Discussion of recovery as a commercial proposition. References on Pitot tube and calculations.

Jan 1, 1914

By W. A. Vine

When a hole is made in a stressed solid, such as rock pierced by mine openings, equilibrium of the solid is destroyed. To restablish that equilibrium the stress condition in the rock surrounding the opening becomes rearranged. This rearrangement may or may not develop local stresses in the vicinity of the opening which exceed the elastic strength of the rock. Since stability of the opening depends, therefore, on the strength of the naturally occurring rock surrounding the opening, this rock is an engineering material of construction, and all rock affected by the associated opening or system of openings may be considered a structure. The term invert is chosen to describe the formation of the structure built from the inside, as it were, and a consequence of mining rather than an entity built for a purpose. By definition, an invert structure is formed when openings are made underground and is com- posed of that material on the solid side of a rock-air interface wherein the stress condition is affected by the associated opening or system of openings. The shape of an invert structure is never clearly defined; the skin of the structure may be mapped, and even described, but the boundary of the structure within the solid rock mass must be arbitrarily set.

Nov 1, 1955