Search Documents

By J. W. King

URANIUM ore was first discovered in the Edge-mont district of the southern Black Hills in the summer of 1951. The discovery was not made known for some time, but after the news leaked out prospecting became intense, and several hundred claims were staked in the spring of 1952. The Hot Springs Sub Office of the Atomic Energy Commission was established at that time and airborne radiometric surveys were commenced by the Government and by private companies. During the succeeding summer another important discovery was made by private airborne surveys in the northern Black Hills, and the area favorable for uranium ore was expanded many times. Between that summer of 1952 and the present, many individuals and groups have explored, developed, and exploited their claims until now uranium ore is produced in significant quantities and substantial reserves have been developed. The Black Hills portion of the geologic map of the U. S. issued by the U. S. Geological Survey is shown in Fig. 1. Sedimentary formations are exposed as a series of cuestas and hogbacks in a roughly annular pattern with the older sediments resting on the pre-Cambrian core, which is exposed in the eastern and southern portions of the dome. The South Dakota-Wyoming state line bisects the area from north to south. The Cheyenne River crosses the southern tip of the Black Hills and the Little Missouri bounds them roughly on the north. Headquarters of the AEC in the Black Hills is the Sub Office at Hot Springs, S. D. An ore buying station is located in Edgemont, 28 miles to the southwest, where a mill is presently under construction. The area of original uranium ore discovery and of principal activity in the southern Hills is a few miles north of Edgemont. Several areas of anomalous radioactivity have been noted between Dewey, S. D., and Newcastle, Wyo. A limited amount of ore has come from the Dewey area and private exploration is active there. The Carlile deposit, largest producing mine in the northern Black Hills to date, lies northwest of the Belle Fourche River near the western extremity of the Hills. Two of the larger known orebodies of the area are located near the Little Missouri River where a small window exposes the favorable strati-graphic horizon of the Fall River sandstone. Small production has recently come from Barlow Canyon, near Devils Tower, Wyo., Fig. 2, and numerous areas of anomalous radioactivity are known in the vicinity. Three producing deposits and scattered radioactivity are found along the state line east of Aladdin, Wyo. Several areas of weakly anomalous radio-

Jan 1, 1957

By John C. Shyne, Eric R. Morgan

BORON as a hardenability agent of commercial importance has been the subject of extensive study in recent years. It has been suggested in the past that boron increases hardenability by combining with nitrogen, thus rendering it innocuous.&apos; More recently it has been proposed that boron increases hardenability by reducing the free energy of sites of ferrite and pearlite nucleation.&apos; The segregation of boron to grain boundaries, the primary site of nucleation, would account for the large hardenability effect of minute additions of boron in steel. This grain boundary theory has found general acceptance while the concept of boron as a nitrogen scavenger has been disregarded. However, the interaction of boron and nitrogen in steel is considered to be important to hardenability because boron may be made ineffective by combination with nitrogen.". * The present work was undertaken to examine some of the effects of boron and nitrogen arid their interaction in steel. A base composition of moderate hardenability was chosen. This was a 0.35 pct C steel containing 2.50 pct Ni and 0.30 Mo. This composition was used because it contained no strong carbide, nitride, or Table I. Composition of Steels by Analysis, Wt Pct Steel C Ni Mo 0&apos; B N* Base 0.35 2.50 0.30 0.0012 nil <0.0001 Boron 0.35 2.50 0.32 0.0012 0.0022 <0.0001 Nitrogen 0.33 2.60 0.35 0.0015 nll 0.0052 Boron plus nitrogen 0.35 2.48 0.30 0.0006 0.0020 0.0040 * Obtained by vacuum fusion technique. boride-forming elements. The other alloys examined were modifications of the base composition and contained nitrogen, boron, or nitrogen plus boron. The compositions of the four alloys used are listed in Table I. The alloys were vacuum melted from electrolytic iron, electrolytic nickel, ferromolybdenum, and fer-roboron. When required, nitrogen was added by admitting a partial pressure of nitrogen over the melt after vacuum melting. The alloys were cast into 21h-in. diam ingots and hot rolled to %-in. sq bars. No ingot pattern was discernible on the polished and etched cross sections of the hot-rolled bars. The alloys were normalized at 1650°F, then machined into standard %-in. diam end-quench hardenability test bars. Four different austenitizing treatments were used: 60 rnin at 1550°F, 45 rnin at 1800°F, 30 rnin at 2000°F, and 20 rnin at 2000°F followed immediately by 30 rnin at 1550°F. The 1550" and 2000°F treatments were carried out in duplicate for each of the four steels. In order to prevent surface oxidation the bars were austenitized while buried under charcoal in an atmosphere of argon. After quenching the bars in a conventional end-quench fixture, the hardness surveys were made in the usual fashion on parallel flats ground along opposite sides of each bar. These were ground 0.050 in. deep rather than the conventional 0.015 in., to avoid decarburized or deboronized regions.5 The austenite grain sizes which resulted from each heat treatment were observed metallographically using Vilella&apos;s etch for martensite. The criterion used as a measure of hardenability was the distance from the quenched ends of the bars at which a hardness of RC 35 was observed. This hardness represented the inflection point on the hardness vs distance plot. Fig. 1 shows the hardenability of each steel after the several heat treatments. The duplicate tests demonstrated excellent reproducibility; the distance to Rc 35 was reproduced within 1/16 in. for duplicate test bars. All four alloys had the same grain-coarsening characteristics. Neither boron nor nitrogen had any observable effect on grain size. The grain sizes resulting from the various austenitizing treatments were ASTM 7 at 1550°F, ASTM 4 at 1800°F, and ASTM 2 at 2000°F. The small amount of boron in the boron steel greatly enhanced hardenability when the samples were austenitized at 1550°F. The low hardenability of the boron plus nitrogen steel showed that nitrogen eliminated the boron contribution to hardenability. Both steels containing nitrogen, with and without boron, exhibited lower hardenability than the base composition when quenched from 1550°F.

Jan 1, 1958

By H. Majima, E. Peters

The oxidation rates of pyrite, pyrrhotite, chalcopy-rite, chalcocite, covellite, bortzite, galem, sphalerite, and stibnite have beet2 carefully compared at 120 oC, using aqueous phosphate solutions buffered at pH 2.7, 7.1, and 11.2 as zvell as in 1.0 M NaOH and in am~onia-containing solutions. Under conditions of these studies, variations in rates of more than a factor of two per unit of mineral surface area were not observed for different minerals in phosphate buffered solutions, except that pyrrhotite showed unusually rapid oxidation rates In acid solutions, and stibnite showed very rapid oxidation rates in basic solutions. In caustic solutions, oxidation vates varied considerably, the most rapid being for pyrite and the slowest for sphalerite. In the presence of ammonia, only copper minerals showed more vapid oxidation rates in neutral solutions. Oxidation rates were measured on the basis of oxygen-consunzption rates per unit surface area of exposed mineral, using equivalent surface areas, mineral mesh sizes, pulp densities, agitation, and oxygen pressure. OXIDIZING pressure leaching of sulfide minerals has been a commercial method of treating concentrates of nickel, cobalt, and copper for over a decade, and recently the treatment of lead and zinc concentrates,&apos; and even the recovery of sulfur from pyrrhotite by such processes, have been shown to be technically feasible.&apos; Furthermore, the leaching of uranium ores by solutions acidified through the oxidation of pyrite and other sulfides present in the ore is commercially practicable.3 5 The mechanisms by which sulfide minerals oxidize in aqueous environments are not yet understood. However, certain generalities can be made for systems containing no unusual reagents, in which oxygen is the oxidizing agent. In acid solutions the oxidation of many sulfide minerals leads to the formation of elemental sulfur.8&apos;7 The attack of some sulfides, notably galena (PbS), sphalerite (ZnS), and pyrrhotite (FeS), at temperatures below about 110°C leads to an almost quantitative conversion of the sulfide mineral to elemental sulfur according to the equation: On the other hand pyrite (FeS2) and copper minerals do not yield elemental sulfur quantitatively. Not more than 50 pct of the sulfur in pyrite is converted to the elemental form in acid oxidation, and this percentage is lowered by higher temperatures and possibly higher oxygen pressures.8&apos;9 Copper minerals sometimes yield elemental sulfurlo&apos;" but, since sulfur can reduce cupric ions with the precipitation of CuS or Cu2S, it is not likely that elemental sulfur is obtained in good yield. In acid solutions sulfur that is not converted to the elemental form always appears as sulfate salts or sulfuric acid. Sulfide minerals that yield elemental sulfur nearly quantitatively on oxidation in acid solutions tend to generate H2S when the conditions are not oxidizing. However, although it has been suggested that H2S is an essential intermediate in the mechanism of oxidation," this is doubtful because it is oxidized very slowly by oxygen. In basic solutions elemental sulfur is never formed, as predicted by thermodynamical considerations, summarized in the form of a potential-pH diagram in Fig. 1. However in neutral and basic solutions, unstable forms of sulfur not shown in the diagram appear during oxidation, notably thiosulfate (SOT-) and polythi-onates (S,O;-, x = 2 to 6).l3,l4 On prolonged oxidation only hexavalent sulfur as sulfate (SOi-) or sulfamate (NHzSO;) is found to remain, the latter appearing only in the presence of ammonia. The oxidation kinetics for thiosulfate by oxygen are the subject of a separate paper,&apos;5 and were studied on the presumption that thiosulfate may, in fact, be a primary oxidation product for sulfide minerals, at least in neutral and basic solutions. A survey of the literature indicated that comparative oxidation rates for different sulfide minerals were needed to establish the role of the mineral structure and its thermodynamic properties on the oxidation rates and mechanisms.

Jan 1, 1967

By R. P. Rothwell

THE milling of silver ores has arrived at a great degree of perfection in the mining districts of our Western States and Territories, and I have thought the record of the practical results obtained at the present time, in a few of the principal districts, would prove of value and interest to many of our members, both at home and abroad. An American silver mill is composed, in descending order from where the ore is dumped, of: 1st. A rock-breaker, usually of the Blake or Alden pattern ; 2d. The battery of stamps, the number of which varies from 5 to 120, generally in batteries of 5 or 10 heads, so arranged that a single battery may stand while the others are running; 3d. The tanks where the crushed ore settles (if it is a wet stamping-mill), or of a drying-floor if the crushing is done dry; 4th. Amalgamating pans ; 5th. Settling pans ; 6th. Agitators or pans in which mercury escaping in the tailings is caught; 7th. Blanket sluices, over which the tailings run, and where mercury and unamalgamated sulphides are saved. A reference to the engravings (see plate), which show one of the latest forms of an 80-stamp silver-mill run by a turbine water-wheel, will show clearly the arrangement of the several parts. THE ONTARIO, UTAH, SILVER MILL. One of the best examples of a silver-mill, and at the same time one of the most successful concerns in the West, is the mill of the Ontario Silver Mining Company, near Salt Lake, in Utah. This mill treats the ore from the Ontario mine, ore which at present is very base, being composed of zinc, lead, and silver sulphides and silver chloride in a quartz gangue. This ore has become baser as the mine attained greater depth, though the vein holds its own, or rather increases, both in thickness and richness. The mill is man¬aged in a skilful and economical manner, though the necessity for * Read at the Montreal meeting, September, 1879.

Jan 1, 1880

By P. J. Potter

Practically all tin-base babbitt metals used in engine bearings are made to customers&apos; specifications, which are many and varied. The copper ranges from 3 to 8 per cent. and the antimony from 4 to 13 per cent.; generally, the babbitt with lower copper content will contain from 4 to 8 per cent. antimony and that with higher copper will have from 7 to 13 per cent. antimony. The allowable lead content varies from 0.20 to 2.00 per cent. If a solder is used as a bonding material instead of tin, the resulting material in the finished bearing will have a higher lead content, but it would not be enough to bring the lead above specifica-tional limits. Impurities such as iron, arsenic and bismuth should be determined in the tin before using to insure a uniform and high-grade product. These points must be considered when segregating and grading the waste that comes from the finishing operations on lined bearings. Classification of SCRAP Because of the extremely rigid nature of most of the specifications for bearing linings it is necessary to use the purest of materials as a base for all compositions. The problem of handling secondary metals is confined almost entirely to the recovery of drosses, spills and turnings incident to the manufacturing operations. As a matter of convenience the waste or scrap may be divided into 10 grades, as follows: 1. Tin from pots where tinning operation is carried out. 2. Tin and babbitt spatters from babbitting operation. - 3. Tin skimmings combined with burned zinc chloride. 4. Borings and reamings. 5. Gates from die-cast bushings and bearings. 6. Drosses from die-cast pots, babbitt foundry pots, and pots in babbittiug room. 7. Babbitt with small amount of bronze from machining operations. 8. Babbitt and bronze borings. 9. Scrap bronze-back babbitt-lined bearings. I 10. Scrap die-cast bearings and bushings. A few of these grades of salvaged material have compositions that make it possible to determine beforehand where they may be used to

Jan 1, 1930

By Howard Eavenson

EARLY in 1917, the United States Coal & Coke Co. secured options on several tracts in Harlan County, Ky., aggregating about 1.9,000 acres in area, and after careful prospecting by outcrop openings and diamond drilling, completed the purchase late in July of that year. This property is situated in the eastern end of Harlan County, south of the Poor Fork f Cumberland River, and extending across Big Black Mountain to the Clover Fork of Cumberland River, a distance of about 7 mi. (11.3 kg.). It extends from the Kentucky-Virginia line westward for about 6 mi. Looney Creek, which empties into Poor Fork, crosses the property for about 4 mi. (6.4 kg.), and as several of the seams within the property outcrop along this stream, it afforded an easy, and the logical, place for development. The property is on the northern side of the geological trough formed by the uplifting of Stone Mountain, on the southern, and Pine Mountain, on the northern side; the northern boundary along Poor Fork is practically at the base of Pine Mountain. This, area has been described in various geological reports.1 The main seam on this property is the one known variously as the "C," Benham, Keokee, Taggart, and Roda; it is, also called, by the Kentucky Geological Survey, the Kellioka seam of the western portion of Harlan County. This seam averages, in this property, about 5 ft. (1.5 m.) in thickness, although local rolls reduce this thickness considerably over small areas; and at the extreme western end of the property the seam splits. It is usually clean, although occasionally a small parting occurs within a few inches f the bottom f the seam; it is one f the best

Jan 9, 1921

By Hans W. Schreiber, David W. Neuhaus

INTRODUCTION The Sunshine Mining Company&apos;s 16-to-1 silver deposit and mine project are located 384 kilometers (240 miles) southeast of Reno and 360 kilometers (225 miles northwest of Las Vegas, near Silver Peak in Esmeralda County, Nevada, at an elevation of about 2,300 meters (7,000 feet). The deposit was being developed, in 1980, with an anticipated mining and milling rate of 150,000 tons per year (500 tons per day). Mining is by underground, blast-hole open stoping with rubber-tire haul-age out of the mine to a straight cyanide plant about 5.5 kilometers (3.5 miles) from the mine. The product is a gold-silver dore which may be further refined at Sunshine&apos;s new refinery in Kellogg, Idaho. The cash required for investment was obtained through the sale of $25 million worth of 6 l/2h silver-indexed bonds. Some $15.0 million were directed toward development of the 16-to-1 Mine. These bonds, which were underwritten by Drexel Burnham Lambert of Chicago in April of 1980, are redeemable on or after April 15, 1985 or payable at maturity on April 15, 1995 at the greater of either $1,000 or the market price of 50 ounces of silver. Behre Dolbear acknowledges the kindness of the Sunshine Mining Company (Sunshine) for allowing the presentation of the subject material for this Case Study. APPLICABILITY AS CASE STUDY Reasons for Choosing 16-to-1 The reasons for choosing the 16-to-1 Mine as a case study follow: 1. The project is simple and compact. 2. The mine is small -- thus relevant to other contemplated precious metal operaions in the western states. 3. The areas of risk are readily identifiable. 4. A change to project financing was under consideration. 5. A substantial decline in the price of silver was experienced during development. 6. Behre Dolbear undertook one of the first feasibility studies of The 16-to-1 and thus has some familiarity with the project. Historical Summary The following history serves as a setting: 1. Late 1920s -- minor "production"(?) via shallow pitting. 2. Mid-1930s -- neighboring Nivlok Mine successfully put into production. 3. Late 1950s (?) -- Callahan Mining Company acquired rights and drilled -- results inconclusive; Callahan turned property back to Arthur Baker, who had originally interested Callahan in 16-to-1 on the basis of its similarity with Nivlok Mine.

Jan 1, 1985

By P. A. Tucker, T. B. Rhinehammer, D. E. Etter, J. E. Selle

The Ce-Cu phase diagram was investigated by differential thermal analysis and rnetallography. Two congruent melting compounds, CeCu2 (817°C) and CeCua (938°C), and three incongruent cornpounds, CeCu (516°C), CeCu, (796°C), and CeCu, CERIUM and copper have been suggested as possible diluents in a liquid-plutonium fueled reactor. As part of the determination of the Ce-Cu-Pu ternary phase diagram, a review Of the Ce-Cu system (798°C), are present in this system. Eutectics exist at 28 at. pct Cu (424°C), 74 at. pct Cu (756°C), and 91 at. pct Cu (876°C). The purity of the cerium used has an important effect on the results obtained by differential thermal analysis. was considered necessary. Previous work by Hanaman was conducted with relatively impure metal: 96.7 pct Ce with 2.5 pct other rare earths and 0.5 pct Fe as major impurities. The metal had a melting point of 715°C as compared to the melting point for pure cerium of 804°C as reported by Spedding and Daane.2 Results presented in this work were obtained primarily by differential thermal analysis (DTA) and metallographic examination of slow-cooled or quenched samples.

Jan 1, 1964

By G. K. Burgess

§ 22. THe results published in Professor Howe&apos;s paper10 of our determinations on the Ac3 and Ar3 points for a series of commercial carbon steels " containing manganese in varying proportion, represent the average temperatures found by taking several (4 or 5) heating and cooling curves. The accompanying curves, Figs. 6 and 7, are, for each steel, the first heating and cooling curves as obtained by the inverse-rate method of Osmond, using a cylindrical chronograph sensitive to 0.1 sec. for recording time. Simultaneous observations were also taken by the differential method with a platinum neutral and plotted by Rosenhain&apos;s derived differential method and gave substantially the same results, the curves having sensibly the same contours in both cases.12 The observations were taken in vacuo on cylinders 5 by 1 in. in length bored to center with a 1/8-in. hole to receive porcelain insulated thermo-couple, and inclosed in an out- and in-glazed Berlin porcelain tube heated electrically by platinum foil wound on the tube. The vacuum was usually better than 0.1 mm. The heating and cooling of the furnace was automatically controlled by a salt-water rheostat with shaped electrodes, giving a uniform rate of heating and cooling.

Jan 1, 1914

By W. P. Frey

The briquet plant of the Lehigh Coal and Navigation Co., at Lansford, Pa., has previously been referred to.&apos; It has passed the stage of experiment and now rests on a foundation practically and financially sound. The purpose of this&apos; paper is to explain how success has been attained, and to set standards for the development of hard-coal briquetting which may eliminate future failures. All the conclusions are based on actual results, avoiding speculation and theory. Up to three years ago, the L. C. & N. Co. used coal-tar pitch as a binder in making hard-coal briquets. The plant operated with a monthly output of 300 to 600 tons and was unable to meet its own expenses. Naturally, no one was satisfied, especially as the ideals of a smokeless briquet were still unrealized. Then came the Dutch oil process, introduced in this country by the General Briquetting Co. of New York. This process uses as binder a small percentage of heavy residue of petroleum, which, being liquid, permits great economy of handling; it also did away with the most objectionable fumes of the former briquets. This oil2 is not absolutely smokeless; heating the fresh fuel to red heat liberates some low-volatile hydrocarbons, yielding a white smoke which is not objectionable. On the other hand, this oil adds to the briquet about 7 per cent. of volatile matter, giving the product a heating capacity equal to that of the best free-burning anthracite coal. The average silt used in the manufacture of these boulets averages 16.5 per cent. chemical ash, corresponding to 12,000 B.t.u. per pound of coal. The Hydrolene used as binder runs about 17,500 B.t.u. per pound, and approximately 7 per cent. of it enters into the mixture, hence 12,000 X 0.93..........................11,160 B.t.n. 17,500 X 0.07.......................... 1,125 B.t.u. Total.....................................12,385 B.t.u. per pound of briquets

Jan 1, 1918

By C. A. Stetefeldt

In my paper on "The Consumption of Fuel in the Taylor Gas-Producer Plants at the Aspen and Marsac Mills" (Trans., xxiii., 134), I mentioned that in the plant which I had designed for the Ontario mill, the gas-tubes were to be covered with thin, corrugated sheet-iron, over which a coating of asbestos-magnesia would be spread in order to effect a good insulation and keep the gas as hot as possible. At the Ontario mill, two Stetefeldt furnaces and two revolving driers are fired with gas. One furnace is connected with a Taylor producer of 5 feet diameter, and the other furnace and the two driers are heated by the gas from a Taylor producer of 7 feet diameter. In the latter case the gas-tubes are necessarily somewhat long, and the cleaning of them takes time. In order to prevent overheating of the tubes during that operation, it has been found advantageous not to provide them with an insulating covering. If a tube becomes red-hot at any place by the burning of soot, this is at once observed, and the tube is closed until it cools down. The tubes con-

Jan 1, 1895

A list of publications of the United States Bureau of Mines, complete from its establishment to the end of June, 1931, may be had upon request. In addition a monthly leaflet of new publications is issued and is sent to those on the mailing list of the Bureau. Publications are separated into three main divisions: 1. Sales Publications.-Those for which a charge is made. Any orders or remittances in payment for sales publications should be sent directly to the Superintendent of Documents, Government Printing Office, Washington, D. C., and not to the Bureau of Mines. Sales publications are classified into (1) Bulletins, (2) Technical Papers, (3) Economic Papers, (4) statistical reports of the mineral resources of the United States, (5) Monographs, (6) Handbooks, and (7) Schedules. Bulletins and Technical Papers present the results of scientific and technical investigations. Economic Papers are analytical studies of production statistics, sources, resources, .distribution, and industrial flow of mineral commodities. The Annual Report, entitled "Mineral Resources of the United States," includes chapters, published separately, on the production and consumption of metals and of nonmetallic minerals. Monographs give detailed results of extensive cooperative investigations of special

Jan 1, 1933

By J. A. Elias, A. J. Heckler

A simplified method is described for the prepauatior~ of comnposite samples for determination of one quadrant of an X-ray pole figure of a sheet material by the Schulz reflection method. Other special conzposite sampling methods were used to investigate specific areas of the pole figures. Plotting nets for these sampling plans were drawn by a computer. Step-scanning techniques were used to obtain detailed information about specific regions of a pole figure. Satisfactory pole figures were obtained for large-grained (0.5 to 1 in. diam) sheet materials. COMPOSITE sampling techniques for preparing one quadrant of an X-ray pole figure have been reported by a number of authors.&apos;-5 All of these methods are similar in that they use a composite sample prepared by stacking and holding together coupons cut from a sheet material. The schulze reflection technique is applicable to the composite sample so that only minor corrections are needed for defocusing and absorption effects. Also, a relatively large area of a sheet is sampled through the use of multiple cross sectional pieces. In general, sampling methods necessary to obtain a composite-type specimen have been formidable enough to discourage their use in routine pole figure determinations. This paper presents a versatile sampling technique which is simpler than those previously described along with an accurate method for obtaining stereographic plotting nets for any orientation of a composite specimen surface. A step-scanning technique is used to obtain more quantitative determinations of specific regions in pole figures, and the composite technique is satisfactorily applied to determine pole figures of very large grained sheet materials. REVIEW OF PREVIOUS TECHNIQUES Mueller and ~nott&apos; first proposed a technique for obtaining one complete quadrant of an X-ray pole figure by using a sheet sample and six different composite samples in which the individual coupons were aligned and held together by two types of jigs. Data from the seven different samples were overlapped to obtain a single quadrant. ~eieran~ and Lopata and ~ula~ obtained a complete quadrant of a pole figure from a single sample prepared by forming a cube from coupons cut from a sheet. These coupons were bonded together using an epoxy cement, and a cut was made at 54.7 deg to the normal, transverse, and rolling directions of the sheet, Fig. I. The normal direction of the cut face projects into one quadrant of a stereographic projection at equal angles to the three principal orthogonal reference directions mentioned above. X-ray reflection data obtained along a spiral path in physical space could then be plotted on a stereographic net offset 54.7 deg from the normal, as shown in Fig. 2. A rotation about an axis representing the surface normal is designated as a, and a rotation about an axis lying in the plane of the surface is 4. From Fig. 2 it is apparent that a tilting angle of no more than 55 deg @ is necessary to obtain the complete quadrant. ~eber~ devised an improved sampling technique by cutting coupons 45 deg to the rolling direction of a sheet, stacking and bonding these with an epoxy cement at an angle of 54.7 deg to a reference plane, and finally grinding and lapping a flat specimen surface parallel to this plane. An important consideration of this technique and that of Lopata and ~ula~ is variation in the diffracting power of the specimen surface due to the bonding medium. While any composite-type sample will have some such variation due to boundaries between coupons, the problem can be minimized by elimination of the bonding medium and by avoiding prolonged etching times which could lead to significant inter lame llar attack of the coupon faces. EXPERIMENTAL TECHNIQUE We were working concurrently though independently on a technique similar to ~eber&apos;s,&apos; but which does not

Jan 1, 1968

By Carl E. Johnson

INTRODUCTION A method for predicting water-flood oil recovery was reported by H. Dykstra and R. L. Parsons&apos; in 1950. It is now generally known as the Dykstra-Parsons method and is widely used by petroleum engineers. The method is semiempirical and consists of a correlation of four fundamental variables. These are: V, vertical permeability variation;&apos; a, mobility ratio; Sw initial water saturation; and R, fractional recovery of oil in place at a given producing water-oil ratio. The correlation extends over a wide range in each of these variables, and may be applied to all formations with initial oil saturations of 45 per cent or greater. The method of calculation originally outlined by Dyhtra and Parsons closely follows their derivation. And this is a convenient way of illustrating the development of some rather complicated ideas. However, in actual use it is more cumbersome than necessary. The purpose of this note, therefore, is to provide a simplified method for making Dykstra-Parsons predictions. A SIMPLIFIED GRAPHICAL SOLUTION The correlation between V, a, Sw and R, corresponding to a given producing water-oil ratio, can be shown on a single graph. This is best done by plotting V against a to show lines of constant R(1 - S, . WOR-0.2). Figs. 1, 2, 3, and 4 show these plots

Jan 1, 1957

By C. L. Burrill

The forecasts presented in this paper constitute an attempt by the writer to predict the pattern of the consumption of petroleum products in the United States during the period of transition from war to peace. Although, in preparing the estimates, secular trends were not overlooked, greater emphasis was placed upon considerations of a cyclical character, or upon influences which might be peculiar to parts of the period. The estimates do not extend beyond the year 1950 because by then conditions in the industry should have returned to normal. The consumption of petroleum products is affected, of course, by changes in the condition of business in general. Before estimates of petroleum consumption could be prepared, therefore, it was necessary to predict the pattern of general business during the period under review, particularly the economic series that in the past have shown the closest relationships with petroleum consumption. It is the writer&apos;s view that business activity in this country (as measured by industrial production) will be higher on the average during the period between the end of the war and the year 1950 than it ever was before during a peacetime period of the same duration. When the war is over, consumers will have saved amounts of money that will be very large as compared with any previous accumulations. There is little question, therefore, as to the financial ability of consumers to purchase goods. The production of many durable consumers&apos; goods, such as automobiles, refrigerators and radios, has been completely stopped since early in the war; also, many semidurable and nondurable consumers&apos; goods have not been available in the quantities or the qualities desired. There is considerable needi therefore, for consumers to purchase goods after the war. The important question is whether consumers will purchase goods in "1arge enough quantities to keep our economy running at a high level. The writer answers this question in the affirmative. The mere existence of very large consumer savings lends considerable support to this view because, with such backlogs of " security," consumers can afford to spend more of their current earnings than they otherwise could. Also, several polls have been taken, which indicate that consumers expect to buy large quantities of a variety of goods. Some of the savings, therefore, probably will go into current consumption. Even though this percentage is relatively small, so that the bulk of the funds accumulated by consumers during the war continues to remain as savings during the period under review, spending should be great enough to start the production cycle and keep it

Jan 1, 1945

By Paul A. Farrar, Felix Ermains, Harold Margolin

The systems Ti-Crand Ti-Vhave been reinvesti-gated in the region up to 40 wt pct alloying addition using both conventional and rapid quenching techniques. The Ti-Cr eutectoid temperature was determined to be at 667° & 10° C and 14.5 wt pct Cr. The solubility of the Cr in a Ti was found to be less than 1 pctat 700"C. The P transus of the Ti-V system was found to be depressed to 510°C at 40 wt pct V and the solubility of V in a Ti was found to be less than 2 wt pct at 700°C. Investigation by a. d. McQuillan1-3and m. k. McQuillan4 on the systems Ti-Co, Ti-Cr, Ti-Cu, Ti-Fe, Ti-Mn, Ti-Ni, and Ti-V has cast doubt as to the position of the ß/a + ß boundaries in many of these systems. Their investigations were carried out using hydrogen pressure and/or rapid quenching experiments, as opposed to the conventional quartz capsule techniques employed by most other investigator.&apos;" By these methods, the ß/a + ß boundary was found to be lower than that obtained by conventional techniques in all except the Ti-Fe system. In the latter, the ß/a + ß boundary was essentially the same as the boundary obtained by conventional technique.7&apos; On the basis of rapid quenching results in the Ti-Cr system, M. K. McQuillan4 placed the eutectoid temperature below 550°C whereas other investigations using conventional techniques had placed the eutectoid variously as between 650&apos; and 700°C,5 between 675&apos; and 700°C,6 between 650" and 675°C,7 at 670°C,8 and above 625"C.la9l3 In order to check these results, a reinvestigation of four of the systems was undertaken using both conventional and rapid-quenching techniques. The Ti-Fe and Ti-Mn systems will be dealt with in anoth er paper, with only the Ti-Cr and Ti-V systems being discussed here. EXPERIMENTAL TECHNIQUES Alloys employed for the delineation of the systems under investigation were prepared from iodide titanium sheet capsules containing the alloying materials,

Jan 1, 1962

By M. J. Hordon, M. A. Wright

ReCENT work has indicated that the substantial decrease in the rate of fatigue crack propagation for aluminum observed below a critical vacuum level can be attributed to the depletion of oxygen or water vapor from the vicinity of the fatigue crack opening.&apos; At reduced gas pressures, generally below 10-2 Torr with fatigue strain amplitudes in the range *1 to 2 x 10-3 and cyclic loading rates of 25 to 50 cps, estimated rates of oxide or hydroxide monolayer adsorption on newly formed crack surfaces can fall behind the actual rate of crack extension. Changes in the critical pressure required for the transition in fatigue behavior with changes in temperature, strain amplitude, and cyclic frequency can be interpreted from variations in the adsorption and crack growth rates.&apos;" Although the adsorption model generally appears to explain the enhanced fatigue resistance of reactive metals in vacuum, the specific adsorbing gas species and nature of the adsorption mechanism are uncertain. In addition to the direct dissociation and adsorption of O2 on the metal surfaces,3 the dissociation of H20 and subsequent adsorption of H ions have been advanced for aluminum alloys.4 The present note describes some measurements of the fatigue behavior of 1100 aluminum in reduced partial pressures of specific gases including O2, H2O, and H2 in order to provide additional experimental data. Cantilever-type specimens of 1100-H14 aluminum were fatigued in cyclic reverse bending at constant strain amplitude using a multispecimen vacuum apparatus and procedure described previously.&apos; After initial vacuum evacuation to 1 x 10-7 Torr, the appropriate gas species was bled into the system through a calibrated leak valve. The input rate was adjusted to maintain the desired pressure level under continuous evacuation, thus minimizing possible changes in gas composition during testing. High-purity input gases including 99.9 pct O2, 99.999 pct H 2, and water vapor from triply distilled H 2 O were used to provide residual pressures. Trace amounts of contaminant species were limited by passing the Oz and H 2 input gases through liquid-nitrogen-cooled copper coils prior to entry to the test chamber. Care was taken to repeatedly flush the gas lines and valves before testing to minimize the effect of adsorbed contaminants. Residual gas pressures in the range 10-6 to 5 x x3 Torr were monitored by an NRC ionization gage corrected for each gas species. In the higher-pressure range, 5 x 1CT3 to 5 x 10&apos; Torr, an NRC alphatron gage was used. In operation, eight simultaneous fatigue tests were conducted at a constant strain amplitude of *1.2 x 10 at cyclic bending rates of 25 and 50 cps to give an average fatigue life of 6.5x 105 cycles-to-fracture at standard atmosphere and 3.3 x 106 cycles in 1 x 10"7 Torr vacuum. Representative results for the effect of residual O2, H2O, and H2 contents on the fatigue life are shown in Fig. 1 for tests performed at 50 cps. It is apparent that the presence of either O2 or H2O gas in the system at partial pressures greater than 10"3 Torr was noticeably detrimental to the fatigue life. In contrast, the enhanced fatigue resistance typical of high-vacuum environments was retained with pure H 2 through the pressure range up to 1 Torr. For partial pressures of H2 gas above 1 Torr, the fracture life noticeably decreased. The critical Hz

Jan 1, 1969

By A. Ghosh, T. B. King

The kinetics of the discharge reaction: 20&apos;- (in silicate melt) = O,(g) + 4e- at a platinum anode in lithium silicate melts have been studied al 1350°C by galvanostatic methods. Plots of the sleady-state overpotential, q, as a function of the logarithm of the current density, i, showed injlections and were linear only at high current densities. The value of the overpotential was influenced by bubbling gas through the electrolyte. The ocer potential was also studied as a function of time. The rise and decay of overpotential were very slow processes. At low current densities transport is the likely rate-controlling process but at high current densities passivation of the electrode, Presumably by an oxide film on the surface, seems to be a contributory functor. IT is well-established that molten silicates behave as electrolytes&apos;5 and, except in a few cases,6 conduction is entirely ionic. Moreover, it is supposed that a possible, and perhaps predominant, mechanism for phase boundary reactions between metals and slags is similar to that in corrosion whereby anodic and cathodic processes occur at unrelated sites, the metal serving to conduct electrons.1&apos;8 Thus electrochemical studies of some slag-metal reactions would seem to be a useful way to diagnose the rate-controlling steps in the overall reaction. The electrochemical method is, in principle, a better diagnostic tool than the direct chemical method for the following reasons: 1) The partial electrochemical reactions, which are simpler than the overall reaction, may be studied individually. 2) The rate of reaction can be controlled at will and independently of the concentrations of reactants. 3) Fast reactions can be studied by relaxation methods.&apos; Esin and his coworkers5&apos;10"12 have pioneered such studies in silicates and have deviloped some ingenious techniques. Not all of their findings, however. can be accepted without a good deal of further work. In this investigation, the kinetics of the oxygen discharge reaction: 202- (in silicate melt) = Oz(g) + 4e- [I] at a platinum electrode were studied by both steady-state and transient galvanostatic techniques. Interest in this reaction was first developed as a result of the findings of Fulton and chipman13 that the reduction of silica, in a silicate slag, by carbon, dissolved in liquid iron, is a very slow reaction. Subsequent work, for example, by Rawling and ~lliott,&apos;~ has demonstrated that the reaction under these conditions must be slow, because the rate is limited by diffusion of oxygen in the iron to the metal-crucible phase boundary at which a CO bubble may be nucleated. Further work by Tarassof,&apos;~ in which the reduction of silica by aluminum dissolved in copper was studied, has shown that under these conditions, where carbon monoxide evolution is not involved, control of the reaction rate resides in diffusion of silica in the slag phase. However, there is no practical way of inducing sufficient convection in the system to make it clear that the phase boundary reaction is indeed fast. The overall reaction of silica reduction involves the discharge of silicon ions at cathodic sites and oxygen ions at anodic sites. In the examples cited, the discharged ions are dissolved in a liquid metal. In the present study of oxygen ion discharge, gaseous oxygen may be evolved at high current densities or oxygen may simply dissolve, possibly as oxygen molecules, in the silicate at very low current densities. The discharge of an oxygen ion at an anode must, in silicates less basic than the orthosilicate composition, be preceded by a reaction in the vicinity of the electrode, such as: which makes oxygen ions available. Platinum was chosen as the working electrode since it is comparatively inert to oxygen and is, therefore, expected to come rapidly into equilibrium with the electrolyte and with gaseous oxygen. Minenko, Petrov, and Ivanova16 have measured the electromotive force at a platinum electrode in molten silicates as a function of the partial pressure of oxygen in the atmosphere, the concentration of oxide ions in the melt, and the temperature. They found platinum to behave as a reversible oxygen electrode. At two different oxygen pressures, Po2 (I) and Pq (11). the electromotive force is given by: where F is the Faraday constant, equal to 23,060 cal per v equivalent, indicating that the electrode reaction is as written in Eq. [I.]. Platinum has been similarly used in molten silicates by other inve~ti~ators. "&apos;~~ In this investigation platinum was used only as an anode, since a current deposits other elements on its surface and changes its characteristics.

Jan 1, 1970

By E. C. Wright, P. W. Mumma

This paper describes some properties of steels in the composition range 0.10 to 0.30 per cent carbon and 1 to 7 per cent chromium. It is well known that some steels of this type develop high tensile strengths upon receiving comparatively simple heat treatments, such as ordinary air cooling from appropriate temperatures, with or without subsequent tempering treatments. These high strengths are frequently associated with unusual toughness as measured by the Izod or Charpy impact test. The chromium content, in addition to imparting the above properties, enhances the resistance to corrosion and improves the strength and oxidation resistance at elevated temperatures. Moreover, these steels have good forging and fabricating properties, as evidenced by the fact that several thousand tons of seamless tubing have been made during the past five years from steels containing 0.10 to 0.25 per cent carbon and 5 per cent chromium. Composition and Properties of Materials Tested Twelve 15-lb. induction furnace heats of the compositions shown in Table 1 were prepared, using low-carbon open-hearth steel base melts

Jan 1, 1933

By Frank C. Roe

Two cogent and ubiquitous facts have supported a constant search by the ore processing industry for better wear resistant materials in equipment. First, designs and types of equipment change or improve continually to meet the economic and physical demands of different and/or leaner ores. Second, practically all equipment is subject to impact and abrasion conditions that probably are more severe and extensive than in any other industry. Development and testing by operators and equipment manufacturers alike, has produced an extensive variety of longer lasting metal alloys, rubber, plastics, ceramics and other materials to improve equipment performance under different specific conditions. The need for diversified materials becomes obvious upon the simple realization that no two beneficiation operations are identical. Among the variables in the handling of ore are: 1. Size and weight of ore particles. 2. Hardness and sharpness of ore particles. 3. Concentration of ore particles in liquid or gas suspension. 4. Velocity and direction of particle impact toward equipment surface. 5. Coefficient of friction between ore particles and equipment surface. 6. Temperature of operation. 7. Chemical environment of operation.

Jan 12, 1967