Search Documents

K. T. Aust and J. W. Rutter (General Electric Research Laboratory)—We find it difficult to reconcile the activation energies determined by Gifkins with his general conclusion that "migration during both creep and grain growth can thus be treated on the basis of the same model" (that of Lucke and Detert). Gifkins finds the activation energy for grain boundary migration during creep to be 24.5 kcal per rnol and that for grain boundary migration during grain growth to be 7.5 kcal per mol. The calculation carried out by Gifkins of the activation energy for grain boundary migration during grain growth, using the Lucke and Detert model, gives a value of 20 to 24.5 kcal per mol, rather than his experimental value of 7.5 kcal per mol. The theory of Lucke and Detert was developed to account for the rates of migration of grain boundaries in the presence of impurities during grain growth. The theory does not take into account the effect on the boundary migration of another, simultaneous process such as creep deformation and would be expected, therefore, to be applicable only to migration during grain growth. The fact that Gifkins measured a different activation energy for boundary migration during grain growth (7.5 kcal per mol) from that during creep (24.5 kcal per mol), although the specimens were of the same composition, shows clearly that such an effect exists under his experimental conditions; the presence of a simultaneous creep deformation markedly affects the boundary migration process in comparison with what would be observed under the same conditions but without the creep deformation. The failure of McLean's equation (Eq. [4] of Gifkins' paper) to give a satisfactory dislocation density difference for boundary migration during creep is not surprising, since the activation energy which must be used in this equation refers only to the elementary atom transfer process of grain boundary migration. This activation energy value is approximately 6 kcal per mol for zone-refined lead, as determined in both the grain boundary migration experiments of Aust and Rutter31, 32 and the grain growth experiments of Bolling and Winegard.33 Using this activation energy value, McLean's equation gives reasonable agreement with observed migration rates for grain boundaries moving free of the influence of impurities.31, 32 The value of 24.5 kcal per mol is probably associated with the presence of impurity atoms, as Gifkins suggests. It should be noted, however, that this value was obtained using lead of only one composition and measurements at only two temperatures. The work of Aust and Rutter3"' on the effects of tin, silver, and gold on grain boundary migration in zone-refined lead in the temperature range from 320" to 200°C, as well as the work of Bolling and Winegard34 on the effect of silver and gold on grain growth in zone-refined lead, shows that the measured activation energy is markedly dependent upon the kind and amount of solute present. Gifkins' work does not permit evaluation of the effect of the 8 ppm of impurities other than oxygen present in his specimens. One incidental point: the symbols used to designate the experimental points of Fig. 6 appear to be in incorrect order in the figure caption. As the caption is printed, it would indicate that larger grain sizes were obtained after annealing at 47°C than at 100°C, which does not agree with the text (point M, p. 1019). Finally, it seems clear from Gifkins' results that any serious attempt to determine whether grain boundary migration and grain boundary sliding during creep occur with the same activation energy, as Gifkins suggests and McLean rejects, must take into account the effects of impurities on these two processes, Although the work of Weinberg35 indicated that adding small amounts of copper, iron and silicon to aluminum did not affect the grain boundary shear behavior, it should be noted that his starting material contained approximately 60 ppm of impurities. Gifkins' results indicate impurity effects at an impurity level of 8 ppm, suggesting strongly that the most significant impurity range to be investigated lies substantially below that value. R. C. Gifkins (author's reply) — As Drs. Aust and Rutter suggest, the results under discussion may have to be reinterpreted in the light of their own work on grain boundary migration, which was not available to me when the paper was written. Because of their work, Aust and Rutter attach more importance than I did to the activation energy for grain boundary migration during annealing (7.5 kcal per mol) obtained from a "direct" plot of log-rate against the reciprocal of absolute temperature. At the time it was obtained, this value seemed rather low, although it was similar to the value obtained by Bolling and Winegard.36 It was then, and still is, difficult to accept this value because of the low value of the index in the power law for grain growth, which seemed to indicate the influence of impurities. It was also concluded that the low value of the activation energy might have arisen from the manner of selecting rates of grain growth which were truly comparable at the two temperatures. There were many other indications in these experiments and those on recrystallization during creep3? that an impurity, probably oxygen, was of importance. The model for grain-boundary migration which Lucke and Detert had proposed was an obvious possibility and its use yielded an activation energy for boundary migration during annealing of 20 to 25 kcal per mol.

Jan 1, 1961

By A. Tanaka, K. G. Carroll

The existence of local room-temperature plastic flow in germanium, which has been a subject of controversy for nearly two decades, has recently received renewed attention, albeit no more agreement than hitherto. Phenomenologically one major facet of the problem has been reduced to the question whether or not indentation can be effected in germanium without the introduction of cracks. That plastic flow can be induced at room temperature by fracture appears to have been rather convincingly demonstrated recently by Suzuki and Kamada and by Noble and Henisch.1 The literature contains both direct and incidental references to Vickers and Knoop indentations showing no cracks, within resolution of optical microscopy. Recently, however, following a controversy on the subject,2,3 johnson4 made a study of indentations produced by spherical indenters and concluded that these are accompanied by cracking. This study in-

Jan 1, 1969

By R. W. Raymond

The death of Louis Janin, which took place Mar. 6, 1914, at Santa Barbara, terminated the earthly career of almost the last survivor, and one of the most illustrious members, of that group of American mining engineers and metallurgists who, in the last quarter of the nineteenth century, directed the development of the mineral resources of the Pacific slope. Louis Janin was born in 1836 at New Orleans. His grandfather, an officer in the French army, had emigrated to this country, with his family, at or before the outbreak of the French revolution. His father became an

Jan 1, 1915

Jan 1, 1946

1. Any society of undergraduates at a technical school, comprising students in any branch of engineering, metallurgy, chemistry, geology, etc, may be recognized by the Board of Directors in its discretion as an Affiliated Student Society, and its name, to¬gether with the names of its president and its secretary, may be published in MINING AND METALLURGY or the DIRECTORY of the Institute. The members of such a society will not be named individually on the membership list of the Institute, but may at any time be proposed for election as associates or junior associates of the Institute, in the usual way. 2. Membership in an Affiliated Student Society, certified by the official representative thereof, and accompanied by suitable testimony as to character and qualifications, will have special weight with the Membership Committee of the Institute, in its consideration of the proposal of a candidate for membership. The Affiliated Student Societies receive the following privileges: 1 A copy of MINING AND METALLURGY free; 2. The use of Employment Service; 3. The use of MINING AND METALLURGY for publicity purposes, such as printing notices of their activities, etc ; 4. Assistance in obtaining speakers for their meetings, lists of moving-picture films, etc. To retain the privileges of the Affiliated Student Society, its officers must keep in touch with the Secretary of the Institute and advise him of its activities. The foregoing plan is not confined to students in mining engi¬neering or metallurgy. Any undergraduate society of engineers may avail itself of the privileges offered. Societies desiring to be recognized as Affiliated Student Societies are requested to make application to the Secretary of the Institute, giving particulars as to their nature, membership and officers. The accompanying list gives the names of the Affiliated Student Societies as of April 15, 1927, and their presidents and secretaries, in so far as they have been reported to the Secretary of the Insti¬tute.

Jan 1, 1923

By R. F. Campbell, R. F. Miller

SIXTEEN steels containing different combinations of chromium and molybdenum, in amounts up to 5 per cent of each element, were examined for microstructure and hardness after air cooling and after furnace cooling from suitable austenitizing temper- [ ] atures. Diagrams summarizing the structures and hardness resulting from these two cooling rates are presented (Figs. 3, 4, 7).† Data were also obtained on the influence of these two elements, individually and in combination, on the depth 0f decarburization observed after furnace cooling (Fig. 8). COMPOSITION OF MATERIAL The chemical composition of the steels investigated is given in Table I. The plain carbon steel was made in a 25-ton Heroult electric-arc furnace, while the alloy steels were made in a 4.5-ton Ajax-Northrup elec- [ ] tric induction furnace. The cast ingots were hot-rolled to I.75-in. bars. AIR-COOLED SERIES The I.75-in. bars were forged to flat plates, 0.25 in. thick, from which specimens 0.5 in. wide by 2 in. long were cut. The specimens were pretreated to improve their homogeneity by heating to I830°F. (1000°C.) for 20 min. and oil quenching. They were then reheated to I740°F. (950°C.) for one hour and air-cooled, after

Jan 1, 1941

By Joseph C. Buchen

In principle, productiorl of salt from sea water is a simple operation. The sun and wind cause evaporation of sea water trapped in ponds, and what is left is principally salt. Commercial production, however, requires consideration of many factors. First is a high consistent annual rate of evaporation, as well as large areas of suitable low-lying ground close to economical shipping facilities. The south end of San Francisco Bay has these requisites. Large ponds are built, by using clamshell dredges to build up levees to a height of approximately 3 ft. on ground usually lower than sea level, so that the water may be taken in through tide gates without pumping. Ponds are divided into extremely large concentrating ponds and smeller crystallizing ponds. Approximately ten times more area is required for concentrating than for crystallizing. The concentrating ponds are irregular in shape and size but the crystallizing ponds are rectangular and fairly regular in size, to aid in harvesting. The ocean water is taken into the first of a series of concentrating ponds and gradually moved forward from pond to pond as it increase:: in density, reaehing the crystallizing area as a saturated brine. This brine is pumped into the crystallizer at the beginning of the net evaporating season, usually in May, and further evaporation causes its sodium chloride content to deposit on the bottoms of the ponds. The brine must be drawn off and a fresh supply added from time to time to prevent other undesirable salts from depositing with the sodium chloride. Harvesting usually begins near the end of August and now is accomplished almost entirely by mechanical means. After harvesting, the salt is stored in large sbockpiles until required for shipping or refining. The greatest amount is used for industrial purposes and is shipped without any processing other than screening, but all salt for domestic use produced by the Leslie Salt Co. is refined by the racuum process, giving a produet consistently testing over 09.9 per cent sodium chloride.

Jan 1, 1938

By Joseph C. Buchen

In principle, productiorl of salt from sea water is a simple operation. The sun and wind cause evaporation of sea water trapped in ponds, and what is left is principally salt. Commercial production, however, requires consideration of many factors. First is a high consistent annual rate of evaporation, as well as large areas of suitable low-lying ground close to economical shipping facilities. The south end of San Francisco Bay has these requisites. Large ponds are built, by using clamshell dredges to build up levees to a height of approximately 3 ft. on ground usually lower than sea level, so that the water may be taken in through tide gates without pumping. Ponds are divided into extremely large concentrating ponds and smeller crystallizing ponds. Approximately ten times more area is required for concentrating than for crystallizing. The concentrating ponds are irregular in shape and size but the crystallizing ponds are rectangular and fairly regular in size, to aid in harvesting. The ocean water is taken into the first of a series of concentrating ponds and gradually moved forward from pond to pond as it increase:: in density, reaehing the crystallizing area as a saturated brine. This brine is pumped into the crystallizer at the beginning of the net evaporating season, usually in May, and further evaporation causes its sodium chloride content to deposit on the bottoms of the ponds. The brine must be drawn off and a fresh supply added from time to time to prevent other undesirable salts from depositing with the sodium chloride. Harvesting usually begins near the end of August and now is accomplished almost entirely by mechanical means. After harvesting, the salt is stored in large sbockpiles until required for shipping or refining. The greatest amount is used for industrial purposes and is shipped without any processing other than screening, but all salt for domestic use produced by the Leslie Salt Co. is refined by the racuum process, giving a produet consistently testing over 09.9 per cent sodium chloride.

Jan 1, 1938

By Carl Henrich

I have read with particular interest that portion of the discussion by Anton Eilers referring to the high-lime (and also high-alumina) slags made by August Raht in 1881, while smelting the Horn Silver ores at Franklin, Utah. The two analyses of such slags, furnished by Mr. Raht to Mr. Eilers are: (a) Not determined in this analysis. (b) Not given in Mr. Eilers' paper. Oxygen ratio, A1 as base. I. 0 in acid: O in base:: 18.1:18.9:: 0.96:1 11. 0 in acid :O in base:: 18.7:17.5::1.06:1 Average: 18.4:18.15=1.01:l Oxygen ratio, AI as acid. I. O in acid: O in base: :23.2:13.8:: 1.68:1 11. O in acid: O in base::23.1:13.5:: 1.76:1 Average: 23.15:13.4 = 1.73:l By assigning to alumina the the of a base, Mr. Eilers deduces the formula 3Feo.-2SiOa + 4Cao.2SiO². The nearest approach to a simple formula expressing the average composition of these slags, which I can figure, is 9RO.Al2O3.6SiO2. Allowing a ratio of 4Feo : 5Cao, we have for this formula:

Jan 1, 1917

By Ali M. Heidarieh Zadeh, Raghu N. Singh

The paper presents a stability investigation of shaft intersections and pit bottom roadways in the vicinity of upcast and downcast shafts at a colliery in the U.K. Aschemeof instrumentation was aimed at monitoring the strata displacement surrounding the pit bottom roadways and shaft intersections with a view to ascertaining the origin of the strata movement and effectiveness of the control measures. The bore- hole instrumentation results together with a theoretical analysis suggested that the cause of instability could be attributed to the drivage of a roadway within the shaft pillar. A semi-empirical technique was used to calculate the amount of support resistance required to reinforce the pillar to take additional abutment load. A rock bolting system was designed to provide a required increase in thrust capacity of the roadway support. The results indicated that roadway closure was effectively controlled after installation of bolts indicating efficacy of the control measures adopted.

Jan 1, 1982

By Fred P. Peters

T. D. Yensen.*—As my information is of a negative nature, I think it belongs under this paper. We are particularly interested in magnetic materials and we would like very much on occasions to make use of powder metallurgy. We have tried repeatedly to use powder metallurgy in preparing our nickel alloys but always. with negative results; that is, we cannot get as good magnetic properties by powder metallurgy as we can by starting with a molten material. We have tried by all possible means to make materials' like 50 per cent iron-nickel alloys by powder metallurgy. The compacts can be regularly lorged and rolled but no matter what we do in the way of annealing, the magnetic properties come out very much poorer than if we start with molten material. F. V. Lenel. †—I want to mention one characteristic of articles made from metal powders which distinguishes them from die castings; that is, their wear resistance. Die castings usually are made from zinc or aluminum alloys and a few copper-zinc alloys; all of them are comparatively soft and not very wear resistant. I know of a number of cases where powder metallurgy rather than the die-casting method was used for producing a certain part because higher wear resistance was needed than could be attained in die castings. A, J. LanghammeR.*—The subject of powder metallurgy is somewhat difficult to discuss, and portray, in the time that his been allotted. Most of you would rightly be bored if we went into details. However, I will cite one incident that possibly will help illustrate some of the potentials. Last summer I was in Washington and met Navy officials for the purpose of studying the possibility of making a certain part by powder metallurgy. The part is highly intricate and I happened to remark that the material cost would be high; that is, the cost on one raw material. Promptly a high-ranking Navy officer said: "Mr. Langhammer, if you must pay x dollars a pound for the raw material, but achieve the desired results, the cost of the finished part would still be low."

Jan 1, 1945

By J. E. Hanlon, J. D. Wolf

The relaxation peaks observed in plastically deformed materials at low temperatures have been reviewed by sack1 and Niblett and wilks. 2 In particular, the dislocation-relaxation in columbium has received considerable study.3-6 The present work deals with the lower-temperature dislocation-relaxation peak (referred to by Chambers and Schultz as the a peak) in columbium and Cb-5 pct Zr. The columbium and Cb-5 pct Zr specimens were machined to 3/8-in.-diam by 7-in.-long rods from bars hot-extruded at 1200°C. The internal friction and resonant frequency of the samples were measured in torsion at kilocycle frequencies at a maximum strain amplitude of -10-6. The interstitial content of both materials was approximately 70 ppm N and 200 ppm 0. The dislocation-re laxation peaks were measured in the hot-extruded state and after successive anneals. Fig. 1 is a compilation of the data. The resonant frequencies for the columbium and Cb-5 pct Zr samples were, respectively, 5.5 and 6.5 kc. Other workers have noted that the dislocation-relaxation peaks in columbium are not characteristic of a single relaxation time. As can be seen in Fig. 1, the zirconium addition further broadens the spectrum of relaxation times. The magnitude of the modulus defect as computed from resonant-frequency data also reflects this extension. The occurrence of the low-temperature a peak at a position 20°K higher in Cb-5 pct Zr as compared to pure columbium, in the hot-swaged state, suggests a decrease in the average dislocation mobility for the alloy. The authors do not feel that these data are sufficient to permit an interpretation in terms of any detailed models.

Jan 1, 1967

By Ralph H. Sweetser

MUCH progress in -blast-furnace construction and in the manufacture of firebrick for furnace linings has been made since the publication of Bulletin 130 of the U. S. Bureau of Mines on "Blast-Furnace Breakouts, Explosions and Slips, and Methods of Prevention," by F. H. Willcox in 1917. At the time of publishing this report comparatively little information was available to blast-furnace men as to the fundamental facts relating to the character of blast-furnace refractories. Some of the accepted theories of only a few years ago have been completely reversed. The mortality of blast-furnace linings used to be so great that nearly every furnace plant had one or more complete linings in the brick shed ready for use in case of a lining suddenly "going out"; it was generally accepted that a furnace could not "keep her lines" more than two or three years at best, and often a hot spot in the shell would develop, or a breakout occur in the hearth or bosh within a year or two after blowing in on a new lining. In some respects these frequent relinings were not so detrimental as to he a complete loss because they afforded opportunities to take advantage of advances in blast-furnace practice. At present the cost of relining has greatly increased, but the life of a lining has also increased. Anything less than five years on a lining is now considered a short blast.

Jan 1, 1932

By Aloys H. Wohlrab

[THE conditions that govern the selection of a suitable type of detachable bit for the small isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may of be able to adopt the practice of larger mines because of necessary capital expendites for equipment for detachable-bit sharpening and shanking. The perfect detachable bit, suitable for all conditions, has n yet been developed. CONVENTIONAL DRILL BIT IN USE That drilling speed increases as the hit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests married out by Holman Brothers Limited1 with 7/8-in. show that when bit sizes are reduced from. 1 ½ in. 1 3/8 in., and 1 3/16 in., to 1 3/8 in., 1¼ in., and it' in., respectively, the volume of the hole is15 per cent less and the drilling speed 4q per cent higher. Recent tests by the United States Bureau of Mines2,3in hard, uniform basalt showed that a reduction in average gauge from 2.077 to 1.826 in., a difference of 0.251 in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and 14° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr characteristics) by some mines.4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and I4° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as can be forged economically. Shop practices and costs have been discussed in earlier papers.5,6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert.7 REQUIREMENTS FOR DETACHABLE BIT FOR HOLLINGER Under these circumstances, it was apparent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in]

Jan 1, 1942

By J. W. Dougherty, J. M. Douglas

THE Hollinger gold mine is in the Porcupine mining division, District of Cochrane, in the northern part of the Province of Ontario. The adjacent town of Timmins, with a population of 25,119, lies 490 miles by railway north of the city of Toronto. GEOLOGY The property is situated on the northwest limb of a major syncline, which pitches northeast at approximately 50°. The principal rocks of the Hollinger area are of pre-Cambrian age and consist of altered, schistose, Keewatin lava flows intruded by stocks of schistose, quartzfeldspar porphyry generally assigned to the Algoman period. The structure of the Keewatin series is extremely complex as a result of close folding and some faulting. The schistosity, trending north 70° east and dipping steeply to the southeast, is most highly developed along a subsidiary anticline in which the major porphyry bodies occur. The ore bodies, which exhibit three principal structures, consist of quartz veins and associated pyritized wall rock. Some lodes are composed of en echelon veins, others exhibit a main quartz body with branching stringers and a third consists of a single definite lead. Gold, in a coarse visible form, may be confined to quartz in some ore bodies but in others it is finely divided and is found not only in quartz but also associated with pyrite in the adjacent wall rock. In many veins the distribution of gold is such that there are several ore sections, separated by areas of low-grade material, in the same vein although its physical appearance remains unchanged. The veins form a very complex pattern in an ore zone which in places attains a length of 6000 ft. and a width of 4000 ft. They are most abundant in the Keewatin lavas in the neighborhood of the porphyry bodies. Few of the veins are persistent for long distances, though some

Jan 1, 1940

By G. B. Gould, F. M. Gibson

IN DECEMBER, 1934, the joint Committee on Fuel Values, of the American Institute of Minim and Metallurgical Engineers and the American Society of Mechanical Engineers, submitted a preliminary report, which briefly stated its conclusion that it was not possible to devise any formula for the valuation of coal, based upon the various physical and chemical properties, that would be generally applicable. That report also listed those chemical and physical properties of coal that are generally recognized to have some effect on its use in steam plants, and those physical characteristics of steam plants which affect, in one way or another the relative importance of the properties of coal used in them. Since then, the Committee has considered and discussed in greater detail the interrelationship of the properties of coal and plant characteristics. The conclusions of the Committee are summarized below, with certain recommendations regarding engineering procedure, which will promote the collection of more easily correlated observations with respect to this subject, and thus advance more rapidly the accumulation of data capable of general application.

Jan 1, 1936

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

By Charles E. Parsons

One of the greatest factors in our industrial development is cheap and convenient power. Long-distance electrical transmission has now reached such a stage that it is feasible, and practicable, to utilize the water-power of the country which was heretofore too remote for consideration. In all of the changes of energy from its various sources to its electrical applications, water-power stands pre-eminent in point of economy. Power-users the world over have endeavored to utilize this force in preference to any other, and until long-distance transmission was found practicable it seemed that every available water-power in this section of the country was doing its full share for the benefit of mankind. The success of each great industrial development has been clue in a greater part to some one man one who is just a step in advance of the rest in his particular field; one who is able to grasp a situation and foresee possibilities; and, above all, one who has that indomitable pluck and perseverance which sees in each obstacle one more step toward success. Such a mail is Eugene L. Ashley, for it was through his efforts that the development of the greatest power on the Hudson river was made possible. For several years prior to 1897 the various properties along the river between Glens Falls and Palmer Falls were in the hands of speculators. These men knew the value of waterrights, but they had not the ability to assemble the properties and finance such an undertaking. In 1897 Mr. Ashley began buying these water-rights, and, after two years of litigation, title mas secured to all of the properties along each side of the river, and the Hudson River Water-Power Company was organized to construct a dam and transmit power to the surrounding cities and villages. A contract was let for a dam

Jan 1, 1904

By J. E. Tobey, David R. Mitchell, J. H. Kerrick

DETAILED knowledge of purchase specifications established by coal consumers is essential to the successful design and operation of a coal preparation plant. ANTHRACITE Specifications should be considered by both the consumer and the producer as guide posts outlining a certain path for both to follow. Plants differ, therefore specifications must differ to meet the varied requirements. Specifications are not of themselves a "cureall" or an assurance of complete satisfaction in fuel utilization. Specifications should not be regarded as a license to engage in an orgy of buying any and all coals that may happen to fall within their limits. This would lead to the indiscriminate mixing of coals which may vary in their burning characteristics. Different coals of equal grade tend to be individualistic in their burning characteristics. Rather, specifications should be used to help simplify coal selection, to reduce the actual number of coals used over a given period; in other words, to have a stabilizing influence on coal or customer turnover. In the final analysis, the use of too many coals per year in a plant is costly to both the consumer and the producer. Too many sources usually result in higher operating and maintenance costs for the consumer and higher sales costs for the producer. Finally, the statement included in the report accompanying the comprehensive Coal Selection Charts prepared by the Coal Committee of the National Association of Purchasing Agents, and released in 1938, is significant. This Committee worked diligently for a period of 15 years seeking to find a scientific and reliable method for selecting coals. The two following paragraphs are quoted from its report: More important is the fact that no ready-made classification or set of specifications can possibly replace the judgment and resourcefulness of an experienced combustion engineer or fuel technologist, nor the usual need for full scale plant tests under the exact conditions of use before a final decision is made.

Jan 1, 1950