Search Documents

Briefly, an open stope is one in which the ore is taken out and no filling is put in; the only support for the walls may be posts or pillars of ore. Such a method is limited to orebodies with strong walls and ore strong enough to stand unsupported over the back of the stope. Details vary and depend on the dip of the vein, mode of breaking ground, method of handling broken ore, and so forth. The examples given are the Beat-son, Birmingham district, Mineville district, and Cornucopia.

Jan 1, 1925

By Bruce E. Grant, Thomas Jancic, Lawrence G. Dykers, Frank Buchella

Principal factors influencing equipment selection can be grouped into five basic categories: tonnage requirements, ore and waste; topography and property line considerations; ore control requirements; physical characteristics of ore and waste; and climatic considerations. Loading, transporting and ground preparation equipment are largely determined by tonnage requirements. Large size equipment is appropriate for a production of about six million tpm, medium size for three million tons and small size for one million tons or less.

Jan 12, 1973

By Frederick Burbridge

The Morning silver-lead-zinc mine of the Federal Mining & Smelting Co. is about 'two miles northwest of Mullan, Ida. The lode is a metasomatic fissure vein. The orebody is approximately 2000 ft. long within the bounds of the property and varies in width from knife edge stringers to 50 ft. It has been developed to a depth of 3600 ft. and stands nearly vertical in Revett quartzite, which .strikes north 65" west. The high-grade veins and lenses are generally mixed with waste (siderite, quartz, and quartzite). The average grade of ore to sorting plant in 1921 was 4 oz. silver per ton, 8.6 per cent. lead, and 4.1 per cent. zinc. Wall rock stands only a short time without timbering. The minimum angle of gravity flow is 45". The ratio of waste sorted out to ore is 6 per cent. No gases are generated underground and temperature has no influence on mining operations. Fresh air is forced down the air raise and up the main shaft. Drifting and Stoping Main drifts 12 ft. wide and 13 ft. high are driven every 200 ft. (vertically) and are connected by raises 125 ft. apart. These raises consist of three compartments (chute, tramway, and timber slide) and are for the purpose of ventilation, access, and hoisting supplies to stopes. Ground is stoped between raises. Chutes are placed every 25 ft. for drawing off ore broken in stopes. Waste for filling is obtained from waste raises off the stope in walls or waste is dumped from the level above down the chute compartment of raises, which is bulkheaded so that waste can be drawn off at any floor as required. Timbering Posts and caps for square sets (varying in diameter from 6 to 24 in.) are cut to length in a sawmill on the surface. No preseratives are used. Timber is taken on a flat car along drifts to a raise nearest the working place and hoisted as required. Practically no timber is salvaged for

Jan 1, 1925

By S. L. Hoyt

IN technological studies on steel considerable emphasis has been placed on the identification of the foreign inclusions, testimony of which is adequately given in the metallographic literature covering methods for their identification. The outstanding accomplishment in this field is the scheme devised by Campbell, Comstock and Wohrman for identi-fying various oxides, sulfides, silicates and other constituents by syste-matic etching tests and microscopic examination.1 The time involved in carrying out this procedure has led to attempts to secure quicker methods, or at least to shorten the time required to secure essential information. An example of this is the use of dark field illumination, but when this was tried out by the authors it was found that cavities and pits on the polished surface appeared bright on a dark field and could not be distinguished from small glassy inclusions. Still another means is the Leitz Ultropak, an instrument equipped with optical units for the illumination of the specimen by reflected light to secure an effect similar to dark field illumination. The structures are made visible in exceedingly sharp details by utilizing the inherent properties of the samples, such as refractive index, absorption coefficients and reflection powers. We have had no experience, with the Ultropak, but a recent paper by Benedicks and Löfquist3 describes methods for

Jan 1, 1934

By E. S. Greiner

Germanium and silicon have been plastically deformed in torsion at elevated temperatures. Slip took place on the four {Ill} planes. Dislocations, revealed by etch pits on a (111) face, occurred in rows that were traces of operative slip planes. THE plastic deformation of germanium and silicon by bending and tension at elevated temperatures has been reported by Gallagher.&apos; Transla-tional slip during plastic flow in these materials, according to Gallagher&apos; and Treuting,&apos; occurs on (111) planes. Recent work by Treuting&apos; indicates the direction of slip to be <1l0>. The present paper describes the plastic flow characteristics of germanium and silicon deformed by torsion. Torsional deformation was accomplished by twisting 1/4x1/4x2 in. specimens held in molybdenum grips and contained in an atmosphere of helium in a transparent quartz tube and heated by an external resistance furnace. The angular displacements were measured on a graduated circle with a pointer attached to the movable grip. Temperatures were measured with a chromel-alumel couple; the hot junction was within the quartz tube and in close proximity to the specimen. Photographs of samples of germanium and silicon twisted at 850" and 1180°C, respectively, are shown in Fig. 1. The germanium was twisted 230" per in. and the silicon 80" per in. These deformations are larger than those used in experiments to be described later and are presented only to emphasize the extensive plasticity of these materials. Germanium A single crystal specimen of germanium (n-type, 7 ohm-cm resistivity) with a (111) plane normal within 3" of the torsion axis, Fig. 2, was chemically polished with CP-4 solution" and then twisted 9" during the twisting of these specimens of germanium, the slip lines from the (lli) plane should have appeared in the four lateral faces instead of in only two. Perhaps the absence of rotational slip is brought about by the square cross-section. A cylindrical specimen would have a more uniform stress distribution in torsion than one with a square cross-section, and may deform by rotational slip. A specimen of germanium (n-type, 5 ohm-cm resistivity) twisted less than 8" per in. at 550°C, was cut to expose the (111) face 19" 28&apos; from the torsion axis, Fig. 4a. This face, after metallographic

Jan 1, 1956

Jan 1, 1888

By T. L. Loucks, E. T. Guerrero

Pressure drop characteristics in a system composed of two adjacent concentric regions of different permeability were studied. The differential equations for continuity of mass flow in the two regions were solved using the Laplace transformation and the necessary boundary conditions to give the pressure distribution in the composite reservoir, the resulting equation for pressure drop at the inner boundary was evaluated for a variety of composite reservoirs and compared with the results for a uniform reservoir. From this study it was found that under certain conditions the permeability in both zones, as well as the size of the inner zone, can be determined from the pressure drop curve. INTRODUCTION The theory for the pressure distribution and pressure build-up behavior of a well producing a single, slightly compressible fluid from infinite and finite homogeneous reservoirs was presented by Hornerl and Miller, Dyes and Hutchinson.2 Extensions on this original work to provide improved and extended interpretations and better agreement between theory and observed results have been made by Matthews, et a1,3 van Everdingen,4 Gladfelter, et al5 Stegemeierand Matthews,6 Hurst and Guerrero,7 and Perrine.8 More recently Lefkovits, et al,9 studied pressure build-up behavior in bounded reservoirs composed of stratified layers. Houpeurtl0 has suggested various approaches to the general problem of variable permeability and porosity but presented no analytic solutions for particular permeability variations. Albert, Jaisson and Marionll studied the finite composite reservoir and presented numerical solutions to the unsteady-state case and an analytical solution valid only for large times. They also studied the so-called pseudo-steady state for several examples of radial permeability variations. Very similar examples have been treated in the unsteady state with application to pressure build-up by Loucks in an unpublished manuscript. More recently Hurst12 has presented the complete point-sink solution (valid for all times) for the infinite composite reservoir. He applied these solutions to interference between oil fields along with an even more elegant application of his explicit solution to the material-balance equation including water influx. Mortada 13 approaches the same application by avoiding the point-source limitation but gives the solution for the aquifer region which is valid only for large times. Hopkinson, Natanson and Temple14 have treated both the finite and infinite composite reservoir obtaining the pressure distribution for the inner zone valid for large times. This paper presents a theoretical study of the pressure distribution in an infinite composite reservoir composed of two adjacent concentric regions of different permeability. The object was to determine the manner in which pressure drop at the inner boundary of a composite reservoir depends upon time, the permeability of each zone and the size of the inner zone. Expressions for the pressure distribution in both zones are developed which take into account the radius of the sink and are valid for small times as well as large times. It was felt that an understanding of the pressure drop behavior in various composite reservoirs would be of assistance in the interpretation of some pressure build-up curves which do not behave according to the theory derived for uniform systems. Often the region surrounding the wellbore is either more permeable or less permeable than the reservoir because of the various drilling and completion practices. The effects of reduced permeability due to drilling-fluid invasion and of increased permeability due to fracturing or acidizing need to be more carefully defined. Therefore, an equation for the pressure drop in a composite reservoir was developed, and the effects of both the permeability in each zone and the size of the inner zone were studied. STATEMENT AND SOLUTION OF PROBLEM BOUNDARY CONDITIONS AND ASSUMPTIONS The physical system studied was a composite

By Benjamin LeRoy Miller, Joseph T. Singewald

For a number of years Russia, India and Brazil have outranked all other countries as producers of manganese ores. During the 5 years immediately preceding the European war, the average annual production of Russia was 844,000, of India 694,000 and of Brazil 200,000 long tons. Since the outbreak of the war there has been a considerable falling off in the Russian and Indian production, particularly in the former, whereas the production of Brazilian ores has been greatly increased, amounting in 1914 to over 250,000 tons and in 1915 to nearly 350,000, with conditions favorable for a still larger production in 1916. Manganese is one of the few industrially important metals that are not produced in the United States in quantity commensurate with our needs, so that we have been compelled to import annually about 300,000 tons, having a value of over $2,000,000, and these ores have been obtained from the three countries mentioned above. Their rank as contributors to our imports of manganese ores was India, Russia, Brazil; and in 1913, Brazil contributed only one-fifth. During the past 2 years Brazil has furnished rapidly increasing quantities to this country, and, with the falling off of imports from India and Russia, has become our principal foreign source. In 1914, Brazil furnished two-fifths of the imports and more than India or Russia, and in 1915 over nine-tenths. The manganese ores of Brazil are consequently of more than usual interest to us at this time. The Manganese-Ore Distbicts of Brazil , The manganese mining industry of Brazil dates from the year 1894, and since that year the total production has been over 3,000,000 tons. With the exception of a small quantity produced in the State of Bahia from deposits west of the City of Bahia, this output has come from the

Jan 1, 1917

By D. L. King, B. A. Schepman

A number of unique thickener mechanism designs with the operating results achieved in various installations are discussed. These unusual designs include new types of raking arms, lifting devices, and feed-wells employed to obtain higher underflow densities and minimum operator control or improved overflow clarity. Several installations of large thickeners in which the underflow lines pass upward through the center to eliminate tunnels are reviewed. The location of the lines and pumps with the maintenance and operating records are included. Several types of automatic lifting device controls are used to provide storage in the thickener. Some of the installations employing underflow density controls are achieving excellent operating results. Thickeners or sedimentation basins are used in minerals beneficiation plants for three basic purposes. These are 1) Concentration, or to raise the density of a liquid-solids slurry. 2) Clarification, or removal of finely divided solids from a slurry. 3) Hydroseparation, or removal of a specific fraction of solids from a slurry. The concepts that control the size and configuration of basins used for these purposes are different. Likewise, different equipment is properly employed to accomplish these various objectives. The pattern of liquid and solids flow in the clarification zone of a sedimentation basin used for thickening or raising the density of a pulp normally is not critical. That is, the solids normally will drop or plunge to the bottom quite readily, and the liquid separates itself from these solids so as to overflow the basin in a relatively clear condition. When clarification or removal of finely divided particles is to be accomplished, the flow patterns in the basin are extremely important. The velocity of the incoming stream must be dissipated and the liquid flow distributed ]In the tank so that the feed is not divided into streams that flow directly to the overflow carrying the fine:ly divided solids that are to be removed. Similarly, the configuration of the arms that provide the raking and thickening of the pulp is not as important in basins primarily devoted to clarification. In thickening, the design of the arms and the manner in which the pulp is moved or worked, can contribute appreciably to the thickening process and achievement of a higher density underflow. THICKENING As the grade oi ore bodies throughout the world generally decreases, and chemical processes, hydro-metallurgy, and other more refined methods of minerals beneficiation are required, problems in thickening become more acute. Difficult operating conditions, previously encountered only occasionally in thickening metallurgical slurries, or clarifying process streams in the mill, are now the rule rather than the exception. Fig. 1 illustrates some of the different types of raking arms that are successfully achieving the desired goals in pulp thickening. The conventional raking arms consist of a relatively simple truss with the blades attached to the bottom chords. This design provides proper Concentration of many &apos;normal&apos; slurries. A modificaiion of this design as shown in the center is being used with excellent results on large thickener basins where it is desirable to have a

Jan 1, 1962

The Library of the above-named Societies is open frond 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated front sources of information. To these the Library, through Its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining neaps, and to furnish general information on the geology and mineral resources of all countries. All communications should he made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be, sent more promptly and in more usable shape.

Jan 1, 1917

By J. E. Kirby, L. B. Schnitz, H. E. Stamm III

The production history of a gas-cap-drive reservoir was reproduced by calculations, and predictions were made for operations under primary depletion, pressure maintenance by gas injection, and pressure maintenance by water injection. Although the general equations used in this analysis have been available to the industry for a number of years, the procedure has not had extensive use because of the unusually large time requirements for developing numerical results. The use of digital computing equipment for processing the calculation work generally reduced the time usually required for an extensive analysis of this type. Calculation techniques were developed that were equally applicable for solving the gar-cap-drive problem, whether digital computing equipment or desk calculators are used. These techniques are outlined and the procedures are illustrated by the field problem. INTRODUCTION The analysis of a gas-cap-drive res-ervoir requires the simultaneous solution of the volumetric balance1 and displacement2 equations. Equations for the analysis of combination drive reservoirs were presented by Wooddy and Moscrip in a previous paper." These equations permit the evaluation of possible operating processes in order that the optimum method of pro- ducing the reservoir may be determined. Although these equations represent the basic technique known for the detailed analysis of gas-capdrive reservoirs, the calculation processes are quite complex and time consuming; hence, the procedure has not had extensive use. Recently, these equations were satisfactorily applied with the aid of a digital computer to investigate the completion history of a gas-cap-drive reservoir under the following operating methods: primary depletion, depletion under full pressure maintenance by gas injection, and depletion under full pressure maintenance by water injection. The use of digital computing equipment substantially reduced the time necessary for making the computations and permitted a more concise investigation of the reservoir&apos;s depletion history than was possible when the desk calculator was used. This more rigorous investigation also permitted a detailed analysis of the calculation procedures necessary in the solution of the gas-cap-drive problem. This paper outlines the procedure of analyzing a gas-cap-drive reservoir and illustrates the process with an actual field problem. CHARACTERISTICS OF THE RESERVOIR ANALYZED Production in the field under consideration is obtained from a Frio formation of Oligocene age at a depth of approximately 5,740 ft sub-sea. The accumulation, which is bounded on the flanks by strand lines, is semirectangular in shape with gentle narrowing toward the base of the structure as shown by the sand limits and completion map in Fig. 1. The reservoir development indicates an oil column of 319 ft that is defined by gas-oil and oil-water contacts. Basic data relative to the characteristics of the formation and the formation fluids are shown in Table 1. The formation exhibits considerable shaliaess and thinning near the oil-water contact indicating that little or no benefit will be received from natural water influx. This is substantiated by the fact that wells completed near the original oil-water contact have not produced water. A sizeable gas cap is present; however, considerable faulting is in evidence, and it is believed that only a limited portion of the gas cap will aid in oil displacement and pressure maintenance. Although the reservoir was in an initial stage of depletion, it was believed that as soon as the equilibrium gas saturation in the oil zone was exceeded and a number of upstructure wells were invaded by the expanding gas cap, the resulting high gas-oil ratio production would rapidly dissipate the natural drive and lead to limited oil recoveries and inefficient reservoir operation. This analysis evaluated the effectiveness of the primary displacement mechanism and

Jan 1, 1958

By Charles Will Wright

Brief descriptions of the occurrence of the various deposits of strategic minerals then known in South America are published in "The Mineral Deposits of South America," by B. L. Miller and J. T. Singewald, 1919; in "Ores and Industry in South America," by H. F. Bain and T. T. Read, 1934; and in many publications on the individual countries. To give a gen.era1 idea of the situation today and possibilities for future output of strategic minerals in several of the countries, the following notes are offered. All tonnages are in metric units.

Jan 1, 1940

WITH the economic situation of the world what it is, we may expect important events in every month of 1922, and January showed us some-what of the nature of things that will happen. The Germans announced their inability to meet in full the reparation payments that were due Jan. 15. The Su-preme Council arranged a plan for them to pay some thing on account every 10 days, and called a conference at Cannes to talk things over. While this conference was in progress Premier Briand resigned and was suc-ceeded by Poincaré. This emphasized the growing differences between British and French policies and interests. The French want to exact the utmost from the Germans; so do the British. The latter think, however, that the French aims will so cripple the Germans that they can not work properly and hence can not trade. Great Britain, with a huge unemploy-ment problem, must have trade. The French thought that Briand was unduly deferring to the British and withdrew their support of him. The other important political developments of the month in Europe were the establishment of the Irish Free State, relieving the British of the vexatious Irish question; and the growing tendency to recognize the Soviet government of Russia and admit its representa-tives into international conferences. In the United States the great political event was the establishment of the dominance of the agricultural bloc in the Senate, which implies the passage of agrarian legislation that will probably be unwise. Economically, there was no progress in the United States. If anything there was probably some reces-sion in the physical volume of business. There were some further reductions of wages, but these were irregular, geographically, and moderate in amount. The great unionized trades maintained the jam. Events of great importance were the formal demand of the anthracite coal miners for increased wages on April 1 and the declaration of the bituminous coal miners that they would resist a reduction at that time. The attitude of these groups is believed to presage labor troubles in the spring. In the metal markets affairs were dull during Janu-ary, but prices were generally firm, save for a little further weakening in iron and steel. In the matter of production, however, there was some quickening of activity, especially in copper, zinc and iron.

Jan 2, 1922

By William J. Douglas, Jack T. Urie, Randall D. Metz

Production and financial planning for a new underground mine requires the coordination of equipment and coal reserves in a manner which assures that resources are utilized efficiently in achieving the target mine production. It is necessary to establish the productions which are attainable at the section level during different mining operations (advance, retreat, development) and under different mining conditions (roof, seam height, resource quality). It is also necessary to identify the interactions between production plans and ventilation equipment So that operations can be carried out without disruptions caused by inadequate ventilation. A set of computer models has been applied in planning a number of new coal, oil shale, and phosphate mines. A critical path production model, CPMINE, was used to determine face production levels for different cut sequences and seam heights, taking into account machine performance characteristics and operational availabilities under these varying conditions. The results formed a production data base for use in the mine sequencing model, MPLAN. This model processes each of the segments of a user-defined mine sequence network (strategy tree) taking into account the equipment available for mining operations and the previously determined production scheme devised by the mining engineer. Mine ventilation was analyzed with an expanded version of the Penn State MVS Ventilation model to determine fan and ventilation shaft requirements for supporting alternative production strategies. The MCOM mine cost analysis model has been applied to evaluate the economic performance of mining alternatives. The results of these studies were used to make decisions relating to equipment selection and acquisition schedules for both room-and-pillar and longwall mining systems. The approach and procedures which were used during these studies are described.

Jan 1, 1983

By Reinhardt Thiessen

During the last few years a type of coal called "splint coal" has been brought to the attention of the United States Bureau of Mines, through numerous inquiries concerning its nature. Until recent years it appears to have escaped general notice. The term "splint coal" is of long standing, but was thought to be merely another expression applied by the miner to coal having certain minor characteristics. When closely examined, however, these coals were found to form a marked and distinct type, with distinctive characteristics that cannot be mistaken. Because splint coals produce a hot cheerful flame, possess a clean blocklike nature, and have a high volatile content, they have lately become much valued for domestic, gas-producer and steaming purposes, and have attracted considerable attention. Mattkohle For many years we have heard from the Germans about Mattkohle and Streifenkohle, in contradistinction to Glanzkohle, but have not realized that they were of a different type from the coals with which we were most familiar. This type of coal was first brought to general notice by Muck, in 1881, who gave a good description of it.&apos; Because this coal is often intercalated with thin sheets of brightly shining cod, Schondorff, who was more familiar with the Saar coals, called it Streifernkohle. This term was later used by Muck also. Still later Potoné² used this term exclusively for the whole group in contradistinction to a class called Glanzkohle, and considered these coals to be composed alternately of Humuskohle and Faulkohle or Mattkohle (Pig. 20). Not knowing the nature of the German coals and not realizing that the term Streifenkohle was applied to a distinct class of coal, the terms of its components as used by Potonié and others were translated to "bright Coal" and "dull coal" and applied to the components of our

Jan 1, 1930

By Eli T. Conner

WITH Thomas G. Fear, chairman of the Coal Di- vision, presiding, the coal miners opened their program Monday morning with a general session at which three papers were presented. The first, "The Classification of Coal for Stationary Steam Generation," was presented by the author, Thomas W. Harris, Jr. In discussion, H. T. Coates inquired if it would not be possible to pick out a geographical coal section, certain seams or a group of mines, which would rank high in a desired feature or features, perhaps giving different -- - local sections or different mines something to designate a rating ("good," "fair," and "poor"). This might be done relative to anti-clinkering, free-burning, ,anti-slagging, smokelessness, friability and grindability. These might be listed or arranged on a map or diagram so that the prospective customer could find a coal that rated particularly high in desired characteristics. C. A. Reed pointed out, in part, that coal producers and sellers have found a bad but necessarily present condition in the country, especially with the smaller user of coal. This is entirely due to the fact that the employer expects his purchasing representative to be a genius and have expert knowledge of everything he buys, coal included, whereas in the larger plants he has and uses expert knowledge from the active organization when necessary. J. B. Morrow said that size rating was important in classifying coal and he emphasized that it was impossible to come to a definite basis on analysis alone.

Jan 1, 1933

By James Johnston

Synopsis.—A description of the working of the mills of this company and the metallurgical practice in vogue, by which a remarkably complex silver ore, averaging 54 oz. of silver per ton (run-of-mine ore), is treated to give a 95.66 per cent. extraction. The main features of the processes are: The cyanide amalgamation of the high-grade ore. The cyanide treatment of the low-grade ore, after extremely fine grinding and close classification, in a caustic soda solution. The use of a wet desulphurizing process to break up refractory silver minerals. The substitution of aluminum dust for zinc dust as a precipitant. The recovery and shipment of over 13,000,000 oz. of silver in bullion at 997 to 999 fine since this metallurgy was inaugurated, about 2.5 years ago. On the completion and successful operation of the mill to treat their high-grade ore,&apos; the Nipissing Mining Co., under the general management of R. B. Watson, started a series of investigations of the possible treatment of the low-grade ore by the cyanide process, so that they would be in a position to market only silver bullion. These tests were run in July, 1911, on a large scale, by G. H. Clevenger, on an average mixture of Nipissing ore. The results obtained by a partiai amalgamation followed by cyanide treatment gave an extraction varying from 90 to 93 per cent. and were sufficiently encouraging to warrant Charles Butters, the company&apos;s Consulting Metallurgist, in recommending that the new low-grade ore mill under contemplation should be a cyanide mill, instead of a concentrator. The cost of such a mill, capable of treating 200 tons per day, to obtain a 90 per cent. extraction at a working cost of $3 per ton of ore treated, was estimated at $250,000. In coming to a decision as to which type of mill should be erected, the concentrator, with the subsequent shipping of concentrates to a smeltery,

Jan 1, 1915

By E. M. MacKevett

The only source of uranium ore in Alaska that has been mined commercially is the Ross-Adams de- posit, a gently inclined, fusiform orebody in alkali granite in which uranothorite and uranoan thorianlte are the chief ore minerals. In mode of occurrence, apparent genetic association with the granite, and to a lesser extent in mineralogy, this type of deposit is uncommon. The mine is in the southern part of Prince of Wales Island (Fig. 1) at an altitude of about 950 ft on the southeast flank of Bokan Mountain. A steep unpaved road 1 ¾ miles long leads to the dock on the West Arm of Kendrick Bay, which can be reached by boat or seaplane from Ketchikan, some 35 miles to the northeast.

Jan 9, 1959

By H. N. Wolcott

AMONG the many cases of replacement of one mineral by another, that of quartz or silicates by pyrite, or even other sulphides, is not uncommon, but the reverse of this process does not appear to have been recorded, even if it has been observed. It, therefore, seemed to the writer that the case described below was worthy of record. FIG. I.-GROUND MASS OF CHALCOPYRITE (C) CONTAINING ROUNDED GRAINS OF PYRITE (P) SHOWING DIFFERENT DEGREES OF REPLACEMENT BY QUARTZ (Q), AND ALSO QUARTZ VEINLETS CUTTING THROUGH THE PYRITE. (PHOTOGRAPHED BY REFLECTED LIGHT.) The specimens described in this paper were obtained by R. B. Morton of Idaho Springs, Colo., from the Old Town Mine, in Russell Gulch, and are in the collection of Cornell University, where the writer studied them. In the rough, the specimens appeared to consist largely of chalcopy- rite, with some grains of tetrahedrite. The polished surface of some of

Jan 6, 1917

By John Wulff, J. H. Hollomon

Service failures in brass condenser tubes are often due to corrosion. One of the commonest types of corrosion reveals a surface structure of redeposited copper.&apos; The study of the effect of alloy addition agents in preventing this kind of corrosion has received impetus from the extensive publication of Bengough and May.2 The mechanism of such inhibition gauged from immersion corrosion,2 cell corrosion,3 and electrolytic potential4 measurements is controversial. This controversy may be attributed in part to a lack of definite knowledge5 of the actual nature of the initial films formed in corrosion experiments. In our own corrosion work on copper and 70-30 brass this lack became apparent and necessitated an examination of surface films by X-ray and electron diffraction methods. The present paper is but an introduction to the subject of inhibition and reports the structure of films formed in active corrodents. Experimental Procedure The arsenical coppers and brasses used in this investigation were made by one of the writers* in the plant of the Revere Copper and Brass Co. at Rome, N. Y. Standard commercial melting practice was followed. O.F.H.C. copper and electrolytic zinc were used and all arsenic additions were made by additions of a master copper alloy. The final analyses are given in Table I. Likewise, the extrusion, cold-rolling, and intermediate anneals employed followed standard usage. Final heat-treatments were given to all materials to produce a similar grain size (0.035 to 0.045 mm. for brass and 0.015 to 0.025 for copper) for the alloys containing various percentages of arsenic. Samples 1/2 by M by 1/4 in. were cut from sheet material resurfaced and finished with 0000 metal-lographic papers. The surfaces were all degreased in alcohol and benzine before immersion. After immersion in the corrodent, they were washed gently in tap water, dipped first in alcohol and then in pure benzine and allowed to dry in the diffraction apparatus. The reflection electron diffraction apparatus used has been described by Burwell and Wu1ff.6 Fig. I is typical of the photo-grams obtained. The X-ray apparatus was

Jan 1, 1941