Search Documents

By R. T. Walker

GROUND waters-hot or cold-containing small amounts of the more common earth acids, such as carbonic acid, silicic acid, hydrogen sulfide, sulfurous acid and sulfuric acid, have only a very limited "solvent effect on dominantly siliceous rocks, whether of igneous or sedimentary origin, but in limestone they often form extensive cavities; and such "limestone caves" are the only openings of considerable size and continuity in rock formations that do not owe their existence directly and almost wholly to dynamic action. Limestone caves such as are developing at the present time must have been formed in all past geological ages in which limestone beds existed and where suitable conditions for the development of such caves prevailed; hence it would seem a reasonable expectation that, in the course of geological history, a certain number of ancient limestone caves must have been utilized as channels for the passage of mineralizing solutions, during portions of their course, at least, and that, in consequence, orebodies must have been deposited in such caves. Such a conception is not novel; it was proposed many years ago, but its possibilities, as explaining certain types of ore deposits, have been rather lost sight of in the development of the theory of the metasomatic replacement of rocks by minerals. It is the purpose of this article to assemble evidence to show that many of the orebodies found in limestone beds have been deposited in pre-existing caves; to discuss the criteria whereby such orebodies can be distinguished from others which have been formed along fissures and fracture zones traversing limestone, by the more common method of metasomatic replacement, analogous to orebodies in other formations; and to describe certain orebodies-particularly the "ore channels" of the Tintic district, Utah-as illustrative of the principles discussed. Limestone caves may be divided into two classes: those formed by cold, descending surface waters, which emerge again at some lower elevation as cold springs; and those formed by hot, ascending waters of deep origin or circulation, which attain the surface as thermal springs. Although these two classes are similar in many respects, there are certain characteristic and inherent differences whereby they can usually be distinguished.

Jan 1, 1928

By J. Parke Channing

THESE days of great industrial and social problems in America produce many suggested solutions and great changes. The practical engineer and employer of labor views these problems differently from the labor leader or the social reformer, but as never before he is sincerely interested in solving them in a way that will be just to all. The inevitable tendency of the day is toward "industrial betterment," "safety," "industrial education," "efficiency," and the many other things' which have become so familiar to progressive employers. There is no longer any question that these things are worth while from both the hu¬man and economic standpoints. They "pay" in dollars and cents. The very center of final success in improving conditions and increasing the efficiency of workingmen must be the spirit of fairness and a knowledge on the part of the employer of how to deal sympathetically and intelligently with his employees. Every progressive employer knows how greatly he desires foremen, superintendents, managers and others who possess these qualities. On the other hand, we are all familiar with serious mistakes made by young graduates of engineering schools who have had no opportunity to develop these qualities, and who have no real appreciation of the worth of the workers. Indeed, one wonders whether much ill-feeling, labor difficulties, and many strikes could not be avoided if such men had the right attitude. Is there any way of remedying this condition? If this particular difficulty can be solved, if these young engineers, many of whom are our coming leaders of industry, can be given the right perspective and the right understanding of these other problems in addition to fair, sympathetic methods of handling men, many of our other problems will be solved-not at once, but gradually and permanently, as these men make good and become influential in paths of industrial righteousness and industrial peace. Many progressive employers of to-day have enlarged their own perspective and realize the great importance of enlarging the perspective of those who shall follow them.

Jan 3, 1915

By Donald H. McLaughlin

THE primary function of the mining engineer is to find mineral deposits and fuels in the accessible rocks of the earth and to recover them for the vast needs of our complicated civilization. On him has been placed the responsibility for the exploitation of the nation's and world's mineral resources. The degree to which the minerals of the earth have been utilized serves to an extent as a measure of man's material advancement, as well as an index of the relative strength of nations. The natural endowment of lands, varies greatly, but the intellectual energy of a people is revealed by the way in which they take advantage of their heritage of minerals or reach out to less developed regions by exporting their engineering skill as well as capital to secure the raw materials they need.

Jan 2, 1953

By A. H. Tousley

The cement industry is on the horns of an economic dilemma. Within the last ten years, its over- capacity in the United States has varied from 139- 127% of demand (Fig. 1). The most direct effect of this is seen in cement prices, which reached a peak in 1960, retreated steadily through 1966 and only recently climbed back to the 1960 level again. With prices in a slump and production costs estimated to be up almost 30%, there has been a steady drain on cement profits. Since 1960, labor costs have increased 86% while fuel costs have risen 18%. Meanwhile, customer service costs have also soared owing to the competition for cement customers and the wider variety of available cement products. This search for sales advantage has in turn led to a higher Blaine number, which means more grinding and hence bigger mills, more power, and, once again, higher costs. New plants as well as expansions and revisions to existing plants are also costing more owing to higher

Jan 1, 1971

By Frank J. Tolonen, Nicholas H. Manderfield, Paul Jasberg

EARLY in the study of the low grade iron formations of Michigan, wide variations in their structure and texture became evident. Because of these variations no simple method of concentration is possible, and those portions of the formations that can be exploited profitably under a given stage of metallurgical progress and existing economic conditions must be searched for carefully. Both structure and texture of the formations have an important bearing on their amenability to beneficiation. By structure is meant the banding planes of easy fracture, the porosity, and the degree of leaching. Texture, which includes grain sizes, shapes, and degree of interlocking, determines the amount of grinding necessary to liberate the mineral grains. Structure determines the liberation of portions richer in one mineral. Structure and texture may be termed the gross features of the formation

Jan 11, 1957

By J. E. Steiner, J. M. Hodge, M. A. Orehoski

Ingots of four steels (1045, 1080, Ni-Mo-V, and Ni-Cr-Mo-V) were cast at pressures varying from about 1 to 760 mm of mercury, so as to obtain a range of hydrogen contents in each steel. The susceptibility of these steels to flaking was evaluated by cooling hot-rolled blooms at a range of cooling rates, varying from water quenching to slag cooling, and studying the occurrence of flaking as a function of cooling rate. The steels exhibited differences in susceptibility to flaking, and a tlzreshold value for hydrogen content for each steel was found, below which the susceptibility was very low and above which the susceptibility increased markedly with increasing hydrogen content. Mechanical property evaluations, metallogvaplzic exantinations, and X-my diffraction determinations o,t retained austenite were made on samples from the blooms. A mechanism of flaking which is consistent with the observed behaviors, the effects of hvdrogen content, and the differences in susceptibility among the steels investigated is postulated, based on the results of mechanical property evaluations and metallographic and X-ray diffraction studies. ThE important role of hydrogen as a factor in the occurrence of "flakes" or "hair-line cracks" in steel has now been established by many investigations. These have included investigations by steel producers and forging manufacturers, to whom the prevention of flaking is a very real and serious problem, and many research studies aimed primarily at establishing the mechanism of this behavior Several investigators3 have reported that steels cast at reduced pressures (absolute pressures of about 1 mm) not only are low in hydrogen content but are essentially insensitive to the formation of flakes. These investigations have shown that a general relationship exists between hydrogen content and susceptibility to flaking. The difficulty of obtaining suitable samples of steels of a given composition with the desired range of hydrogen contents, particularly in the relatively large sections in which flaking most commonly occurs, has been the principal obstacle to quantitative evaluations of these relationships. Steels with intermediate hydrogen contents between 1 ppm, and the 4ppm or higher of air-cast steels are generally not available in commercially produced steels. Laboratory procedures, in which the hydrogen is introduced into solid steel samples by heating in a hydrogen atmosphere under pressure, generally involve a limitation in the size of the sample which can be treated, and thus are not representative of the behaviors in large sections. The availability of a facility at the South Chicago Works of U.S. Steel, in which several ingots could be cast from a single heat of steel at total air pressures ranging from 0.25 to 760 mm of Hg, has made it possible to overcome this obstacle and to obtain ingots of a given steel covering the intermediate range of hydrogen contents desired. These ingots, furthermore, are of a size suitable for the production of product with section sizes large enough to be representative of the products in which flaking most commonly occurs in commercial production. In these experiments, this facility was used to study the relationships between hydrogen content and the susceptibility to flaking of four steels, two plain carbon steels at 0.45 and 0.80 pct C and two low-carbon alloy steels representing a medium and a rather high hardenability level. These flaking studies were supplemented by evaluations of mechanical properties and by metallographic studies on samples from the blooms, in order to obtain pertinent information on the factors other than hydrogen content which influence the susceptibilities of these steels to flaking. Based on the results of these tests, a mechanism for the initiation and propagation of the flaking cracks, which is consistent with the observed behaviors, is postulated. MATERIALS AND EXPERIMENTAL WORK Steelmaking and Conversion. To provide material for the investigation, five 29- by 35-in., hot-topped, big-end-up ingots were cast from each of four 80-ton, basic electric-furnace heats of four different steels (a 1045 steel, a 1080 steel, a Ni-Mo-V steel, and a Ni-Cr-Mo-V steel). A double-slag practice was used on all steels and the two plain carbon steels were Si-A1 deoxidized with an addition of 2 lb of A1 per ton, while the Ni-Mo-V and Ni-Cr-Mo-V steels were deoxidized only with silicon and

Jan 1, 1964

By W. H. Class

The embrittling effects of oxygen, ozone, nitrogen, air, and surface residues, on NaCl has been investigated. The embrittlement by ozone and oxygen was found to be associated with the formation of a NaClO3 surface compound. In these cases the initial crack that was responsible for fracture (in a bend test) always nucleated at the corners between the tension and side faces. The behavior of air was very erratic and on certain days did not produce enzbrittlement. During these periods, crystals that had become embrittled by the ozone treatment completely recovered their ductility after a short exposure to the ambient atmosphere, It was established many years ago1 that considerable ductility could be obtained in NaCl single-crystal specimens if the crystal surfaces were dissolved in water either during or immediately prior to the test. The original interpretation of this effect by Joffe attributed the enhanced ductility to the removal of surface microcracks by dissolution. Later investigations2'3 have suggested that the exclusion of air from the specimen surface is the criterion for extensive plastic flow prior to fracture. The air em-brittlement in this later work was attributed to the diffusion of gaseous atoms into the surface layers of the crystal, thereby impeding the movement of dislocations. This model satisfactorily accounts for the reembrittlement observed after further air exposure subsequent to the water dissolution treatment. However, the situation has recently become more complex by the observations in several laboratories4-t that under certain conditions air exposure does not impair the ductility of NaC1. It has also been recognized5 that improper drying operations after water dissolution can leave surface precipitates that lead to embrittlement. Cleavage defects on as-cleaved crystals can often be another source of embrittlement. In the present work the effect of the gaseous atmospheres nitrogen, argon, air, oxygen, and ozone, on the ductility of rock salt was studied extensively. The embrittlement resulting from oxygen and ozone exposures was found to be associated with the formation of a NaC1O3 surface film. It is suggested that certain atmospheres, one of which often can be ambient air, which inhibit the formation or favor the decomposition of this compound, can promote ductility. Thus one aspect of the Joffe effect is certainly related to the removal of surface compounds or complexes by water dissolution. The effect of surface precipitates that remain after drying operations and of cleavage defects were also studied. In neither of the latter cases was the embrittlement as severe as that found with a NaClO3 surface layer. PROCEDURE AND SPECIMEN PREPARATION The nature of the embrittlement produced by the agents mentioned above was studied by means of microscopy, mechanical testing, and X-ray diffraction. Specimens were cleaved from large crystals of optical quality sodium chloride obtained from the Harshaw Chemical Co., and, except for those tested in the as-cleaved condition, were given a 15- to 20-sec immersion in distilled water followed by a rinse in absolute methyl alcohol. The specimens were then blotted on a soft, absorbent paper, and dried by a few seconds exposure to a stream of warm, dry air. Such a procedure was found to give a control surface which was microscopically free of residues. (A few crystals were intentionally painted with a concentrated NaCl solution in order to investigate the effect of surface residues). All specimens were of 0.140 sq in. cross-section. Crystals prepared in the above manner were immediately placed in a gas train where they could be exposed to the desired gases for preselected periods of time. For the oxygen and nitrogen exposures, pure reagent-grade gases were employed. The ozone was provided in the form of an ozone-oxygen mixture (approximately 10 pct ozone) prepared by passing commercial grade oxygen over a strong ultraviolet light source. All gases were dried prior to their introduction into the train. Since argon was found to be completely inert in its behavior (i.e., residue-free specimens that were exposed to argon were not embrittled), it was periodically utilized to check the control specimen surfaces as well as the condition of the gas train used for aging the specimens. After exposure to the gaseous media in question, the crystals to be used for the measurement of the strain to fracture were transferred from the gas train to a protective oil bath (without further exposure to the atmosphere) where the tests were conducted in three-point bending. The apparatus was so adjusted that the load could be applied at a constant, continuous rate. Other Snecimens from the gas train were deformed

Jan 1, 1962

By Chas. Y. Clayton, Francis B. Foley, W. E. Remmers

DuRing the summer of 1919, the late Dr. Henry M. Howe, then Chairman of the Division of Engineering of the National Research Council, organized a committee to obtain a better insight into the behavior of carbon steels under the influence of various treatments by a proper control of the time and temperature factors. During part of 1919 and 1920, work in connection with this investigation was carried on at Dr. Howe's laboratory at Bedford Hills, N. Y. During 1921 there was an enforced hiatus in the work, occasioned by the illness which resulted in Dr. Howe's death in 1922. At that time one of the present authors compiled the results of the work which had been done and this was published in 1923.' Following the publication of this work, it seemed desirable to carry on in the same manner an investigation of steel of C 0.75 per cent., which steel had not been as fully treated as had the other steels of C 0.34 and 0.52 per cent., used in the published work. Furthermore, certain unusual results have been obtained in the treatment of C 0.52 per cent. steel by quenching and drawing, and repetition of this part of the work seemed advisable. This has been done during the past year at the School of Mines and Metallurgy of the University of Missouri at Rolla, Mo., by a cooperative undertaking of the School and the Bureau of Mines, working in conjunction with the Committee on Heat Treatment of Carbon Steels of the National Research Council. The present paper is a report of the results obtained in this work.

Jan 1, 1926

THE John Fritz Medal Board of Award, at its regu¬lar annual meeting Oct. 19, awarded its gold medal to Herbert Clark Hoover. Thus ended a process of selection begun a few years ago. The award was tentatively made a year ago by the Board, which is composed of sixteen recent past-presidents of the four national societies of Civil, Mining and Metallurgical, Mechanical, and Electrical Engineers, having together a membership of nearly 60,000. The sixteen members of the Board are: American Society of Civil Engineers : C. E. Grunsky, Robert Ridgway, George S. Davison and John F. Stevens ; American Institute of Mining and Metallurgical Engineers: William Kelly, J. V. W. Reynders, Samuel A. Taylor and E. DeGolyer; American Society of Mechanical Engineers: Fred R. Low, D. S. Jacobus, Dexter S. Kimball and Charles M. Schwab; American Institute of Electrical Engineers: Farley Osgood, M. I. Pupin, C. C. Chesney and Bancroft Gherardi.

Jan 1, 1928

By C. D. Broadbent

INTRODUCTION The slope stability research plan at Kennecott was developed to serve the specific needs of large, open pit mines; primarily those developed in faulted and highly-fractured intrusive deposits. The program emphasis is on applied research; being defined in this case as research into the engineering mechanics of discontinuous rock and into the related rock property survey and slope design techniques. The program has been developed in phases, with each phase organized to explore more thoroughly the most significant findings of previous work and to improve on techniques found to be applicable. The current work is based on principles developed early in the program and that show promise of having engineering and economic value. A brief summary of the conceptual principles of the program is given to put our current work in context. This is followed by a review of the two cooperative programs done with the U. S. Bureau of Mines. Most recent work is described and interpreted in terms of practical slope design. Although failure-free slopes are a desirable goal, it is recognized that some failures will occur when overall slope designs approach a calculated safety factor of one. A discussion of failure control research is therefore offered. BACKGROUND In 1965 Kennecott management specified that a slope stability technology must be used to achieve optimum development of ore resources. The subject was carefully explored and by 1960 it had been established that there was no technology readily applicable to open pit slope design. Therefore, in 1962, Kennecott Copper Corporation and the U. S. Bureau of Mines agreed upon a cooperative research program having the objective of developing a mine slope stability science. One of the first decisions made by the cooperating groups was that the research must be conducted primarily in the field and not in the unrealistic environments of a laboratory. Accordingly, the Kimbley Pit, an abandoned mine once operated by Kennecott's Nevada Mines Division in Nevada, was selected for the full-scale research. Fortunately, there was near-universal agreement on the basic stability parameters and thus on the areas to be investigated. These parameters were acknowledged to be: (1) anisotropy (generally due to faults or joints), (2) stress, and (3) water; in that order of importance.

Jan 1, 1972

By R. J. Wygal

A method is presented by which homogeneous, isotropic, and reproducible aggregates of particles such as glass beads, sand, ground glass, etc., may be prepared simply and quickly by using a "particle distributor". Several applications of the packing method to the construction of model reservoirs are described. The flow characteristics of these packings me given. Some factors which limit the usefulness of unconsolidated packs for simulating reservoir rock are overcome through artificial cementation of the aggregates. INTRODUCTION Many laboratory studies of porous media are based on experiments using test packs of sand, glass beads and other granular materials. More confidence can be had in the results of such studies if the test packs are known to have uniform properties throughout, to be mechanically stable and to be accurately reproducible. This paper presents a method by which such packs of a variety of shapes and sizes may be constructed using a particle distributor. Some factors which limit the usefulness of unconsolidated packs as a means for simulating reservoir rock are described. A method of overcoming these limitations, which involves artificial cementation of the packs, is presented. DEVELOPMENT Particles packed by the tamping or vibrating techniques are usually either non-uniform or mechanically unstable. An invention by Currie and Gregoryl overcomes these difficulties to some extent. The invention is based on the use of a stream of falling particles impinging on and passing through a distributor matrix of several layers of closely spaced spheres. The particles are well dispersed by numerous collisions with the spheres. They become homogeneously distributed at some distance below the distributor matrix and at that position are collected in the sample container. This apparatus, however, was found to be ineffective when small particles were used since small particles accumulate on the top surfaces of the spheres. An improved distributor matrix was made, first in the form of a stack of five sieves, and then in the more adaptable form of spaced layers of wire screen. Fig. 1 shows a longitudinal view through a five-layered distributor of eight-mesh wire screen. This device gives excellent results.* Fine particles pass through the distributor with very little hold up. The fine structure of the wire matrix with its many deflecting surfaces ensures good particle distribution. There are no dead areas immediately below the screen as were sometimes observed to occur below a matrix of spheres. Using such a device, 20-30 mesh sands were packed to a porosity of 32.1 per cent at rates varying from 0.17 to 6 lb/rnin. The lowest porosity achieved by tamping small increments of similar sands into a container was 33 per cent. Motion pictures at 3,000 frarnes/sec of the surface of a growing pack of 2-3/4 mm glass beads have helped to show the mechanism by which packs of low porosity are obtained. The beads, although packed at the rate of 5 lb/min, were observed to hit the pack surface singly, for the most part, and at well spaced points of impact. Part of their energy is transferred to surface beads which are thereby

The Library of the above-named Societies is open from 9 A.M. to 9 P.M. on all week-clays, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 4, 1913

By J. M. W. Mackenzie, M. H. Buckenam

Flotation experiments using stearic, oleic, linoleic, linolenic, and ricinoleic acids and naturally occuring products rich in these acids as collectors for calcite are described. The results confirm the validity of the rule of Hukki and Vartiainen relating the collecting power and unsaturation of the C18 acids. Reasons for this relationship are discussed and a close relationship between mineral depression and critical micelle concentration is reported. It has long been recognized that the unsaturated fatty acids are in general superior flotation collectors to their saturated homologues. Whereas earlier workers concentrated on saturated and monoethe-noid acids, recent investigations have centered on oleic, linoleic, linolenic, and the substituted mono-ethenoid acid: ricinoleic. From studies of the collecting properties of palmitic, oleic, linoleic, and linolenic acids on ilmenite, rutile, hematite, and magnetite, Hukki and Vartiai-nenl concluded that the collecting power of fatty acids increased with unsaturation of the hydrocarbon chain. Sun, Snow, and Purcel12 investigated the collecting properties of unsaturated fatty acids as collectors for phosphate ores and concluded that the collecting power increased with increasing unsaturation of the hydrocarbon chain up to two double bonds and that further unsaturation decreased the collecting power. More recently Sun3 studied the collecting power of the C18 fatty acids stearic, oleic, linoleic, and linolenic on 37 minerals. The results of these experiments with a few exceptions showed that the collecting power of the acids increased in the order stearic, oleic, linoleic, and linolenic. The relative collecting powers of linoleic and linolenic acids were in many cases altered by the cleanliness of the mineral surface prior to flotation. Sun concluded that linolenic acid may become oxidized by atmospheric oxygen during flotation, a reaction which would reduce its effectiveness as a collector. This deduction is supported by Gaudin and Cole4 who concluded that oleic and linoleic acids do not undergo appreciable oxidation of the double bonds during flotation but that the linolenic acid double bonds are measurably affected. The most complete investigation on the influence of hydrocarbon chain unsaturation on the collecting properties of fatty acids is that of Kivalo and Lehm~svaara.~ These workers using linolenic acid of a higher purity than Hukki and Vartiainen showed that this acid was superior to oleic and linoleic acids as a collector for magnetite. They also found that ricinoleic acid was a more effective collector for this mineral than the other acids investigated, an observation particularly apparent at high collector concentrations. Seeking to explain the superiority of the unsaturated acids these authors considered the effects of critical micelle concentration, surface activity, hydrolysis, and cross sectional area of the hydrocarbon chain in relation to unsaturation. Using what, according to the results of Caviere are erroneous surface tensions of the soap solutions of these acids, they concluded that the surface activity decreases and the critical micelle concentration increases with increasing unsaturation. In view of the data of Cavier, whose results show that surface activity of these soaps increases with unsaturation, the deductions of Kivalo and Lehmusvaara are open to criticism. The degree of hydrolysis of the soap solutions as measured by Kivalo and Lehmusvaara decreases as the unsaturation of the fatty acid increases, a result which helps to explain the superiority of unsaturated acids as collectors. In view of the superiority of unsaturated acids as collectors for many minerals, attention has been directed towards the utilization of fatty acid raw materials such as tall oils and linseed oils which contain considerable quantities of these acids. This paper describes test work to determine the effect of unsaturation of the hydrocarbon chain on the collecting properties of fatty acids on calcite, and includes comparable test work using natural products rich in unsaturated acids. TEST WORK Reagents: The pure fatty acids used were oleic, linoleic, and linolenic. Of these, oleic was supplied by British Drug Houses Ltd. and the others were produced by the Hormel Inst. When not in use these

Jan 1, 1961

By Cyril Stanley Smith

THE art of metallography is mature and the forms in which various micro-constituents appear are well known. Investigations almost without end have disclosed the importance of the exact manner of distribution of phases on the physical properties and usefulness of an alloy. Surprisingly, however, relatively little attention has been paid to the forces that are responsible for the particular and varied spatial arrangements of grains and phases that are observed. Like the anatomist, the metallurgist has been more concerned with form and function than with origins. In this paper it is proposed to develop the simple concept that many microstructures result from an attempted approach to equilibrium between phase and grain interfaces whose surface tensions geometrically balance each other at the points and along the lines where they meet. From this follows a number of principles which may prove to be of interest to the metallographer and of practical use in explaining failures and in designing alloys for particular service. In general, the discussion will be limited to structures obtained after full annealing. The simple principles do not apply to structures resulting from Widmanstatten mechanisms in precipitation, or to other structures not in local equilibrium and in which lattice coherency is a determining factor. INTERFACIAL TENSION Much has been written by physical chemists about the free energy of surfaces, which manifests itself as a measurable surface tension. Two- and three-phase interfaces in fluids seek a condition of minimum energy and approach a geometrical configuration in which the various forces are in vectorial balance.* Measurement of the angles established between the interfaces when in equilibrium provides a quantitative value for the relative value of the surface forces involved. The case of two fluids meeting at the surface of a solid (of great importance in connection with the flotation of minerals) has often been studied, but there have been few investigations of the equally definite interface between two or more crystals of a single solid phase, or the more complex cases where crystal grains of more than one phase are involved. The principles are best illustrated by considering first the case of two and three immiscible liquids. If, as in Fig I, a liquid, 2, is dropped into a less dense liquid, I, it will form a sphere-if gravity and viscosity can be ignored-for in this shape the interface has the smallest possible area. If these two phases should together encounter a third phase in which they are both immiscible, the geometry will change to become that which gives the lowest total energy for all three interfaces. Thus, if the spherical drop of liquid, falling through r, eventually reaches the interface between liquids 3 and I (we are assuming that the density of 3 is greater than 2, and 2 than I), it will assume the shape of a lens, the angle

Jan 1, 1948

By H. S. Martin

Although it was known some years ago at the Utah Copper Co. mills that fine grinding improved flotation recoveries, no accurate data were available until recently as to just how far the grinding could be carried economically. In 1923 the ultimate degree of fineness for flotation feed was supposed to be about 10 per cent. on 65 mesh, with approximately 55 per cent. through 200 mesh, which meant that most of the mineral would pass 100 mesh. At this time Garfield and Wilfley tables were used ahead of flotation and a good deal of the coarse mineral removed prior to the ball mill regrind. Shortly afterwards, mill-scale tests developed the fact that on a feed containing not over 10 per cent. +65-mesh material flotation alone would give a copper recovery equal to that obtained by the combination of tables and flotation, but that on much coarser feed the recovery with flotation alone was lowered. This was at a time when all the sulfide minerals were floated if possible, so that the only requisite was to grind fine enough to free the mineral from gangue. Earliest Use of Microscopic Examination of Tailings As early as 1921, the writer had attempted to determine by chemical analysis the relative proportions of copper minerals in tailings from an ore that made extremely poor flotation results. Chemical analysis was not satisfactory or conclusive, and samples of these tailings were sent to the U. S. Bureau of Mines Station at the University of Utah for microscopic examination. The question at that time was to determine, if possible, which copper minerals had been lost and why, but R. E. Head, in his report, revealed other interesting data. He said in part: Briefly stated, the mineral partieles or grains may be classified into scparate groups as follows: 1. Free grains of pyrite, chalcopyrite, chalcocite and bornite, respectively, which contain 110 other included sulfides; 2. Grains in which all three of the copper sulfides are representel (the core may be of chalcopyrite, partially altered to boruite, these two minerals being cntirely surrounded by a shell of chalcocite); 3. Grains composed of equal amounts of bornite and chalcocite or chalcopyrite and chalcocite. The grains of free mineral particles are perhaps the most numerous, taking the ore as a whole, but it is noticeable that of the grains of combined or associated sulfides

Jan 1, 1930

By E. C. Harder, D. F. Hewitt

Since early in 1916, when it became apparent that the steel industry of the United States could not depend for the duration of the war on several important foreign sources of manganese and might have to depend entirely on domestic ores, the U. S. Geological Survey, with the assistance of several cooperating organizations, has made a comprehensive investigation of domestic manganese resources. The work has included field studies in a number of states well as annual, quarterly, and monthly canvasses among operators concerning current and future production. In order that the interested public might have access to the important results of the studies, preliminary reports concerning the field work as well as periodic summaries of production were issued as promptly as possible. Although numerous summaries of production l2, l3, l4 have been prepared from time to time for the use of the several boards and committees responsible for the conduct of the war, it has been thought for some months that those engaged in the industry, as well as others, might be interested in a preliminary summary of the accumulated geologic and production data. The cessation of hostilities, in November, 1918, probably detracts from the usefulness of much of the material that is here presented, but apart from the historic interest in the performance of an important industry in war time, there is a possibility that some of the conclusions may be helpful to those who continue to exploit domestic deposits, as well as to those who wish to measure the country's independence in mineral supplies. Appropriate final geologic reports are being prepared by the geologists who did the field work. The present authors, having done but a small part of the recent field work, acknowledge with great appreciation the use of preliminary and unpublished reports and the cordial informal cooperation of the following geologists in the preparation of this paper: F. L. Ransome, G. W. Stose, F. C. Schrader, J. T. Pardee, E. L. Jones, Jr., H. D. Miser, Laurence LaForge, J. B. Umpleby, Arthur Keith, F. J. Katz, and E. S. Larsen, of the U. S. Geological Survey. Field work in Virginia was carried out in cooperation with the Virginia Geological Survey, T. L. Watson, State Geologist; in Georgia, with the Georgia

Jan 1, 1920

Ore deposits of commercial grade are local concentrations of great rarity when considered in relation to the area of unmineralized land surfaces, and they must therefore be considered as the products of exceptional and complex conditions. The data collected from a great number of individual deposits are sufficient to permit certain broad generalizations in regard to the conditions favorable to ore deposition which even numerous exceptions do not invalidate. The broadest general relation of ore deposits is with intrusive rocks, and while there are notable exceptions, the great majority of ore deposits have a visible or closely inferred connection with intrusive rock masses. Conditions that permit the dissipation of the ore-bearing vehicles do not permit the concentration of metals in deposits; the prime factor to consider in this connection is that structural conditions must be such as tend to concentrate and not to dissipate the ore-bearing solutions. The disadvantage of extrusive rocks is at once apparent; any metals the magma may have contained are dissipated at the surface and are lost; with the exception of tiny vugs and cracks in quickly cooled flows, no concentrations of metals are known in extrusive rocks, and the lack of confinement and quick cooling apparently do not permit extrusives to exert mineralizing effect upon the rocks with which they come in contact. The close mineralogical similarity between extrusives and intrusives, and the great difference in mineralizing power is a proof of the ease with which magmas part with their metallic content, and of the mobility of the ore-bearing vehicles in comparison with the parent magma.

Jan 1, 1932

By Alexander Squire

One of the principal factors that have contributed to the hesitancy of design engineers to use metal-powder parts is the difficulty experienced in the determination of the mechanical properties of compacted components. Because standard test methods cannot usually be applied in the inspection of such parts, and because adequate special test methods have not been developed, it has been considered desirable to investigate the methods that are applicable. These may then be included in specifications for metal-powder materials and components in order that the design engineer may be assured that the subject parts possess the desired mechanical properties for satisfactory performance. It is known that direct relationships exist between usually nonmeasurable properties as tensile strength and elongation and shear strength and the angle through which compacts may be plastically deformed before fracturing. These correlations are valuable in the inspection of specific parts, but it is necessary to set up standards before they may be satisfactorily employed. Apart from the use of correlations, the number and character of the inspection methods that are applicable to almost all powder parts is limited to three—chemical analysis, density, and hardness. The last of these may or may not be a pertinent characteristic, since the indentation hardness of many powdeied-metal materials is so low as to have little significance. It is, however, occasionally desirable to use hardness measurements as an indication of the uniformity of the structure of pieces of a given type. Chemical analysis reveals very little about the physical properties of metal-powder compacts, since the unpressed powder is usually of a composition almost identical with that of the finished pieces. Density determinations are simple to perform and have the advantage of being nondestructive in character. If the dimensions of a machine part are known (and usually they are), the average density may be determined by weighing a given number of pieces and dividing by the calculated volume of the parts. More accurate measurements may be made by the water-displacement method. It is recognized that mechanical properties of metal-powder materials are related to their density, but usually these relations are determined for only one type of powder, processed under a given set of conditions. Comparisons of the pioperties of compacts formed from different types of powders are made on the basis of compacting pressures instead of density, and for this reason the results obtained by using powders of different types appear widely variant.

Jan 1, 1947

By Alexander Squire

One of the principal factors that have contributed to the hesitancy of design engineers to use metal-powder parts is the difficulty experienced in the determination of the mechanical properties of compacted components. Because standard test methods cannot usually be applied in the inspection of such parts, and because adequate special test methods have not been developed, it has been considered desirable to investigate the methods that are applicable. These may then be included in specifications for metal-powder materials and components in order that the design engineer may be assured that the subject parts possess the desired mechanical properties for satisfactory performance. It is known that direct relationships exist between usually nonmeasurable properties as tensile strength and elongation and shear strength and the angle through which compacts may be plastically deformed before fracturing. These correlations are valuable in the inspection of specific parts, but it is necessary to set up standards before they may be satisfactorily employed. Apart from the use of correlations, the number and character of the inspection methods that are applicable to almost all powder parts is limited to three—chemical analysis, density, and hardness. The last of these may or may not be a pertinent characteristic, since the indentation hardness of many powdeied-metal materials is so low as to have little significance. It is, however, occasionally desirable to use hardness measurements as an indication of the uniformity of the structure of pieces of a given type. Chemical analysis reveals very little about the physical properties of metal-powder compacts, since the unpressed powder is usually of a composition almost identical with that of the finished pieces. Density determinations are simple to perform and have the advantage of being nondestructive in character. If the dimensions of a machine part are known (and usually they are), the average density may be determined by weighing a given number of pieces and dividing by the calculated volume of the parts. More accurate measurements may be made by the water-displacement method. It is recognized that mechanical properties of metal-powder materials are related to their density, but usually these relations are determined for only one type of powder, processed under a given set of conditions. Comparisons of the pioperties of compacts formed from different types of powders are made on the basis of compacting pressures instead of density, and for this reason the results obtained by using powders of different types appear widely variant.

Jan 1, 1947

By Charles E. Weaver

During the past few years there has been considerable activity in prospecting for oil and gas in several parts of western washington. From time to time seepages of oil or emanations of gas have been reported from various places. Several companies have been organized for the purpose of drilling, but only a part of these have actually begun operations. In certain localities very small seepages of oil occur, but up to the present time no oil or gas in commercial quantities has been obtained. In order to determine the conditions which may be favorable or unfavorable to the occurrence of petroleum it becomes necessary to know the character and extent of the geological formations in which such deposits might occur. In other regions where producing wells have been developed it is possible to know what formations contain the oil and what structural conditions influence its concentration in reservoirs or zones. It is usually possible to determine those strata which contained the materials from which the petroleum may have been derived and also the position and distribution of the more porous sandstone belts into which it may have collected. Detailed stratigraphic surveys may even determine the depth at which a certain known oil-bearing zone may be tapped at any particular place. It is also possible to recognize those formations which are presumably barren of oil, as well as those which are absolutely so. In new regions far distant from any of those which are now producing or have produced in the past, it becomes absolutely impossible to foretell whether oil may exist in commercial quantities or not. Assuming that such deposits do exist, it is extremely difficult to predict at what depth the produciqg zone or zones occur. However, in prospecting in a new and unexplored region, use should be made of such laws as have been found to govern the occurrence of petroleum deposits in other well-developed fields. Such deposits in their world-wide distribution are found almost exclusively associated with sedimentary rocks. Areas composed predominatingly of igneous and metamorphosed rocks are to be rcgarded as extremely unfavorable localities for the occurrence of commercial deposits of oil or gas. Assuming that such oil deposits are

Jan 1, 1916