Search Documents

By Ross Glanville

INTRODUCTION The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR can also be expressed as the Optimum Mine Life (OML) in years since the expected mine life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mine life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mine life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low-tonnage mines (such as many underground gold/silver deposits) often lead to sub-optimal results. In fact, an apparently uneconomic deposit at an arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mine properties based on arbitrary production rates. This paper analyzes the interrelationships of variables such as production rates, capital and operating costs, cut-off grades, discount rates, metal prices, etc. The analysis shows that the OML for high-grade/low-tonnage deposits is often in the range of two to four years. Although such mine lives intuitively appear too short to many individuals, it should be noted that, in the past, much of the mining industry became familiar with the economics of large scale mining operations. The rules of thumb developed for such large scale operations should not be applied to high-grade/low-tonnage mines such as many of the underground gold deposits. DEFINITION OF OPTIMUM PRODUCTION RATE The OPR is selected on the basis of maximizing the net present value of the after-tax cash flows. However, as discussed later in this paper, the production rate selected for a particular mine may be somewhat higher or lower than the theoretical OPR as a result of other variables such as: 1) the probability or expectation of additional reserves being discovered 2) the likelihood of being able to custom mill nearby deposits owned by others 3) the configuration or attitude of the orebody, which may place upper limits on the production rate 4) the residual, or salvage values, of the mine/mill facilities COMPARISON BETWEEN DIFFERENT PRODUCTION RATES For an orebody with definite physical cutoffs*, or boundaries (such as faults or unconformities), the total ore reserves at different production rates may be identical. Consequently, for such an orebody, varying production rates result in differing mine lives. Although the metallurgical recoveries, the mine dilution, and other similar physical parameters may vary slightly at different production rates, the major differences are the capital costs and operating costs per ton. The ramifications of these differences are especially important at low production rates (up to approximately 1000 tons per day), but can also be significant at higher production rates.

Jan 1, 1985

By B. J. Shaw, R. Kossowsky, W. C. Johnston

High purity (99,95) Ni-51 wt pct cr eutectic alloy was unidirectionalty solidified at rates of 0.1 to 8 in. per hr. The resulting material was characterized by large grains, approximately 0.5 mm in cross section and extending through almost the entire length of the specimen, parallel to the growth axis. The eutectic structure of specimens the growth at -1/3 The per hr consisted of a continuous nickel-rich phase and chrome -rich lamellae approximately 2 thick, spaced about apart. Specimens were tested in compression at temperatures ranging from —196 to 850"C over which range the 0.2 pet yield strength dp -creased from 160,000 p si to 35,000psi, respectively. Swaging to 40 pet reduction in area, followed by a 30-min anneal at 1000c to remove residual cold work, increased the 0.2 pet yield to 260,000 psi at -196°C, dropping to 35,000 psi at 850°C. The increase in strength was attributed to a residual cell structure. The strength of the alloy could be rationalized by the simple rule of mixtures if one assumed that additional strength is derived front a size effect characterized by is petch equation IN recent years there has been increasing interest in dispersion and second phase strengthening in materials needed for high-temperature applications. inm role of structure on the mechanical The of such alloys has been well established of such some extent accounted for theoretically. and to of how the strengthening mechanisms due to fibers and lamellae operate has been reduced to its fibers form by the fabrication of composites of strong rods unidirectionally aligned in a From work on tungsten-fiber-reinforced copper, for example, it was established that the "Rule of Mixtures" could explain the strengthening.12 " some what more sophisticated technique for introducing strong fibers into copper matrix was used by Hertzberg strong Kraft3 who unidirectionally solidified the copper-chromium eutectic. The use of unidirectionally fied eutectics has advantages in that there are no matrix-fiber wetting problems and fine fibers are automatically aligned and uniformly fiber However, one Is restricted to a specific volume fraction of the second phase. Nevertheless, even though the volume fraction is fixed, the rod or lamella thickness, , can be varied by controlling the freezing interface velocity. Alternatively, the grown material may be worked down by swaging or rolling. Embury and Fisher, " using this approach, drew down pear lite in iron and studied the mechanical properties iron and that the yield strength, oy, was properties.proportional They that d was the wire diameter. It could be inferred that was also proportional to but the work hardening had to be taken into consideration at the same time. By varying the growth rate of the cadmium-zinc lamellar eutectic, Shaw'1 showed that was proportional to without the introduction of work hardening and suggested that the lamellar interface itself contributed to the strengthening of the composite. In this investigation we have evaluated the mechanical properties of the unidirectionally solidified fec-bec eutectic Ni-Cr. This eutectic was selected because it presented the possibility was selected beca temperature, and high corrosion resistant alloy, and also represented a hard-soft phase combination with two completely different slip systems. Specimens were tested in compression and tension up to 850°C and a detailed study of the micro structure as a function of plastic strain and temperature was carried out by light and electron microscopy. It was shown that the composite strength tested in compression can be accounted for by the simple rule of mixtures if one allows for an additional term representing the effect of Intereprese EXPERIMENTAL PROCEDURE 1) Unidirectional Solidification. Fig. 1 is a schematic drawing of the apparatus used to produce 0.2 in. diam by 12 in. long alloy ingots. The crucible tube is alumina, containing the charge which has been is swaged, or machined to 0.195 in. diam. The lower end of the tube is immersed to 0 .195in in.d iam. The upper end is supported by a 10 mil nichrome wire which lowers the crucible mil nic hr the] wire at a prescribed rate. Surrounding the furnace is a graphite susceptor into which a control thermocouple is inserted. The furnace is insulated with fiberfrax and enclosed in a quartz tube. There is a sliding seal at the bottom around the crucible and one on the top so that an atmosphere may be used for the sample and suscep tor. The power for the furnace is supplied from a 10-kw, 450 kc generator. The skin depth (the skin depth at which the field falls to l/e of its value at the outer surface) for graphite (p = 10 (j-ohm-cm) is 0.1 in. at this fre-

Jan 1, 1970

By Frank L. Gaddy

Falls of roof account for over 50% of the fatalities that occur in coal mines in the U.S. Thus, roof control is one of the more important phases of underground mining. In reality, the control of roof influences the system of mining and is a major determinant of the width and spacing of working places, operations at the mining face, ventilation control, and surface subsidence. Frequently, the control of roof is the largest single cost item. Roof control is a never-ending task, not only at the working face and throughout sections where men are working, but along haulways and airways that must be maintained for the life of the mine. This is because roof, even the best of roof, slowly deteriorates, so it must be frequently examined, with corrective support applied when needed. As coal is excavated, stresses are set up in the roof became the previous equilibrium is upset, resulting in pressures that cause fractures and slight, movements that are, frequently, hard to detect. Unless the immediate roof, in the excavated area, is given support by artificial means, it might fall or there might be a succession of falls, varying from a thin scale to several feet, depending on the nature of the top. Exceptions to this are those rare mines, or sections of mines, with hard, strong, nonweathering roof that requires no support. GENERAL CLASSIFICATION OF ROOF There are two broad types of roof as far as support is concerned, the immediate roof above the coal and the main roof. Artificial support for mining purposes is only concerned with the immediate roof as nothing except large blocks of solid coal, or massive concrete, will support the main roof. The immediate roof is generally a few feet thick but can vary from inches to 20 ft or more. There are examples of where there is no immediate roof as the massive main roof lies directly on the coal bed, but this is rare. Impossibility of supporting the main roof and all of the cover

Jan 1, 1973

By Frank Clemes Smith

The study of the so-called refractory gold-ores of the Potsdam sandstone, ores which are probably of wider occurrence and of much greater economic importance in the Black Hills than is generally supposed, has led the writer to formulate in the present paper some of the results obtained in the course of a special examination of these particular ores, conducted at the State School of Mines at Rapid City, So. Dak. Various circumstances have interrupted the work, and it will easily be seen that relatively little has yet been accomplished; but it is hoped that this little may be of sufficient interest to justify a later supplement. Tellurium, discovered by Muller von Reichenstein in 1781, is generally classed as a very rare metal; it is further mentioned by one of our late writers as " of comparatively little importance," and as obtained from its ores by a " complicated process.'' Concerning its rarity, we have some trustworthy evidence below. Its commercial importance, particularly in connection with electrical appliances, has been passed upon by Mr. Edison ; * and it is certain that, in some metallurgical processes for the treatment of gold- and silver-ores, it may be saved as a byproduct at a relatively reasonable expense. The importance of tellurium as a mineralizing agent is emphasized by the remarks of one of our leading metallurgists,jwho, in his own practice and by a wide series of experiments, has found its occurrence to be much more general than has been supposed. Recently the same writer has discussed the occurrence of tellurides and oxidized tellurium compounds in the gold-ores of Cripple Creek, Colo., and in those of the Black

Jan 1, 1897

By L. S. Darken

THE manufacture and treatment of metals comprises operations whose effectiveness depends in large measure upon diffusion phenomena. The significance of such phenomena has, for a few simple cases, long been understood, but in more complex cases it has not been adequately recognized. This paper presents a mathematical analysis of some of the cases in which diffusion leads to the formation of a new phase within the metal, and this analysis provides a basis for interpreting quantitatively many apparently diverse experimental observations recorded in the literature, some of which are outlined in the following pages. OBSERVATIONS RECORDED IN LITERATURE An outstanding instance is the general type of phenomenon in which diffusion of an element into an alloy is followed by a phase change, which most frequently is a reaction (precipitation) of the diffusing element with one or more components of the alloy to form a compound. Thus in certain alloys heated in contact with oxygen not only the usual oxide scale appears but, in addition, beneath the surface, a well-defined zone in which free oxide particles are dispersed with notable uniformity. This zone, commonly referred to as the subscale or zone of internal oxidation, is remarkable in that the visible boundary between it and the unaltered metal is usually sharp. Such a subscale, which appears to have been recognized first in oxidized copper alloys, has been described and studied by C. S. Smith,1 by Rhines,2 and by Rhines, Johnson and Anderson;3 but it appears also in other alloys when they are exposed to conditions that bring about the precipitation of some compound, not necessarily an oxide. Another clear case of this same kind is the diffusion of carbon into a steel containing an element such as molybdenum, chromium, vanadium or tungsten, whose carbide is less soluble in iron than iron carbide, the result being that some part of that element is precipitated as a dispersed carbide. A similar phenomenon may occur on the welding of two alloys each of which contains one of a pair of elements that react to form a compound or a new phase of any sort. But in addition to the precipitation of a compound formed from the diffusing element, other effects may result merely from the presence of the diffusing element. For instance, if homogeneous austenite, nearly saturated with respect to carbon, is heated in contact with silicon in the absence of oxygen, one would expect to find, behind the several iron-silicon phases analogous to a scale, a zone of austenite containing dispersed carbide, because of the fact that silicon decreases the solubility of carbon in iron. As still another example, oxidation of an alloy may result in diffusion toward the surface of one or more of the constituents; for instance, during oxidation of a steel containing an element such as copper, which is less prone to oxidation than iron, there is a notable enrichment of copper just beneath the scale-metal interface. As an example of a yet more

Jan 1, 1942

By Kenelm C. Appleyard

In introducing to an American audience a description of the work done in dry coal separation in England and in Europe generally, it is perhaps desirable to give a short history of the development outside the United States of the particular processes with which the author is connected, and perhaps to stress a little the differences in the nature of the conditions to be faced. England actually presents one set of problems and the Continent of Europe another, since the character of the coals to be treated is entirely dissimilar, and the attitude of the coal industries towards coal preparation is also dissimilar. England for generations has been working by hand good seams of clean coal of the highest possible quality and has not felt any pressing need to clean its coal. Most Continental countries, however, especially in Central and Western Europe, have been working friable and often very dirty coals for so long that a washery is accepted as a part of the normal equipment of a colliery, with the result that the art of wet washing has reached a high state of perfection, particularly in Belgium and Germany. The advent of machine mining has intensified the problems to be faced in all countries, and in England has been coupled with the working out of the best seams in the older coal fields, thus bringing about the necessity of working thinner and dirtier seams with resultant difficulties as regards marketing the products, while Poland, with clean and well prepared coal, has in recent years been attacking established British markets in Scandinavia. In recent years, therefore, interest in coal preparation has been steadily gaining ground in England, although it has not yet reached Continental dimensions. Broadly speaking, the differences in preparation problems between England and the Continent boil themselves down to one of size. In England, for example, with the exception of the Kent coal field, the proportion of coal of a size less than ? in. to the coal less than 2 in. is very much less than on the Continent, and since the principal difficulties in dry cleaning lie in the fines it is easier to produce good figures on

Jan 1, 1931

By Cyril Smith

ALTHOUGH not of the same importance as electrical conductivity, the capacity for conducting heat is nevertheless a very important property of metals and alloys. A knowledge of thermal conductivity is of value in selecting alloys for many purposes and in the calculation of the efficiency of apparatus which is being designed. Unfortunately, the determination of thermal conductivity is extremely slow and tedious, consequently few data have been obtained. A further reason for the lack of information is that there has long been an impression that the thermal conductivity of an alloy is directly proportional to the electrical conductivity and that it can therefore be calculated from the latter. The Wiedemann-Franz-Lorenz law of constant ratio of the two conductivities holds with a considerable degree of precision for all the pure metals, but appreciable deviations occur in certain alloys-particularly those containing nickel-and it seems difficult to predict exactly what the ratio will be. Therefore direct determinations of thermal conductivity should be made whenever the results are, needed with any accuracy. This research is intended eventually to cover all the alloys of copper that are of commercial importance, including the binary alloys of copper with zinc, tin, aluminum, nickel, silicon, manganese, cadmium and phosphorus, and the ternary alloys copper-nickel-zinc, copper-nickel-silicon, copper-manganese-silicon, copper-zinc-tin, etc. Most of these alloys are customarily used in the wrought condition and therefore were tested in the form of annealed rods. A limited number of sand castings were also obtained and examined. This paper contains a complete review of all the previous work that has been done on copper alloys, and includes a detailed description of the apparatus and method of procedure used in the present research, together with the new results obtained on the copper-zinc series, which is the only one completed at the present time. Subsequent papers describing the other alloys will contain the experimental results and discussion only.

Jan 1, 1930

By J. A. Norden

MUCH has been written concerning the hoisting equipment of various mines -throughout the country, but most of the literature on the subject, if not all, describes equipment of extraordinary capacity and the small and medium-sized outfits have been neglected. The hoisting equipment here described is capable 'of handling about 1200 tons per day. It has not been worked, to capacity, but 600 to 700 tons, together with men and materials, have been handled in two shifts without any great effort. Only one shaft extends from the surface to the lowest levels of the mine; see Fig. 1. It is composed of three compartments, two of which are used for hoisting and the third for water, air, and electrical lines, and for sinking purposes. In 1909, this shaft was raised from the 1000-ft. (304-m.) level to the 700-ft. There a station was cut and an air hoist installed. At this time all mining operations were confined to the upper levels of the mine; that is; above the 700-ft. The. ore was-dropped to this level through chutes from the 300-, 400-, 500-, and 600-ft. levels and then lowered in cars on cages to the 1000-ft., which is the main haulage adit, the mill and railroad bins being about 3000 ft. from the shaft. Orebodies were, in due time, developed on the 1000-ft. level and below. Therefore, in 1913, the shaft was sunk to the 1150-ft. level and thereafter sinking was continued at regular intervals until the 1500-ft. level was reached. But, hoisting from the 1300-ft. level was a difficult, and slow process with the antiquated air hoist, so, in 1916, it was derided to raise the shaft to the surface and install a modern, electrically operated hoist. This was completed early in 1917 and the hoist was in operation in March of that year.

Jan 8, 1920

By C. A. Heiland

The following summary is written for the benefit of the practical operator in the nonmetallic field who wishes to know what geophysics has done and may be expected to do in his line of work. His problem is quite different from that of the geophysicist who has operated with various or all methods and has followed the literature, and who is assumed to be familiar with the geologic possibilities and limitations of each method. This article is not written for the latter, although he may be interested in the four or five hitherto unpublished surveys described. To the operator, on the other hand, geophysics is only secondary. His problem is to determine which geophysical method is best suited to his special needs. If he wanted to know, however, which method could be used to locate a certain material of given physical properties, building stone, for instance, he would have to wade through a tremendous amount of geophysical literature, bibliographies and articles, before he could find what he wanted. Therefore, the purpose of this summary is to present the geological problems first and then to discuss the comparative merits of the geophysical methods that can be, or have been, applied. Choice of Geophysical Methods in Oil, Civil and Mining Engineering In the first two of these fields, the geological problems are not nearly so complex as in the metal and nonmetallic mining fields. The selection of the correct geophysical method in these fields is not nearly so difficult for the operator. For oil prospecting, his problems have been discussed exhaustively by E. DeGolyer.(1) † In civil engineering (foundation and ground-water work), the usefulness of electrical methods has been so well established that there is hardly any choice of other methods at present. The situation may be changed in the future with the perfection of the seismic reflection method for shallow depths. In the mining field the operator and often the geophysicist himself finds difficulty in determining which method is best suited for a given

Jan 1, 1934

By J. Van Steveninck, A. C. Pols, R. Feenstra

In the course of time, an increasing number of investigations on jet cutting all kinds of material, such as rock,1,2,3 metal,4,5 and wood6 have been reported to serve various applications. A number of papers have been published on these subject, 7,8,9 some of which refer to jets purposely containing abrasives, termed 'jetted particle drilling'.7 Since such abrasives complicate fluid handling considerably and do not appear to be absolutely necessary for making holes, only conventional drilling fluids have been considered. A large part of our investigation has been performed with the aid of three laboratory-type drilling machines, which permit tests on both micro-bits (1 ½ in. ) and full-scale bits (6 ½ -9 5/8 in. ) . In view of the application of jets in deep holes, care has been taken to simulate hydrostatic pressures as they exist in the field on the hole bottom. These have been found to have a major effect on the bit-penetration rate for various drilling fluids.

Jan 6, 1974

By J. R. Thoenen

IN five years mineral wool has grown to a thirty-million-dollar industry from one whose output was valued, in 1933, at $1,700,000. Ten years ago, in 1928, there were only seven producing companies, with an annual output of but 50,000 tons. By 1936 fifty or more companies were producing half a million tons. The industry is still growing vigorously and will profit from the expected activity in building in 1339, for two-thirds of this material is used for building insulation and to assist in fire-retarding, in both new and old homes. It is as useful in the South, to protect against heat, as in the North, to keep out the cold, if one may speak nontechnically. It is a concomitant of air conditioning, that new addition to the American standard of living that began in theatres, department stores, and railroad dining cars, and is rapidly progressing down to small homes. Here, then, is an industry that is only beginning to have a present, and one with an almost certain important future; one that depends upon mining and the by-products of mining for all of its raw materials; one that every progressive mining man should know something about.

Jan 1, 1939

By T. Egleston

The manufacture of charcoal in kilns was declared many years ago, after a series of experiments made in poorly constructed furnaces, to be unprofitable, and the subject is dismissed by most writers with the remark that in order to use the method economically the products of distillation, both liquid and gaseous, must be collected. It is asserted with truth that the number of kilns required for a large production of iron would be so great that it is doubtful whether any works would be justified in making the necessary outlay for their constructiou, but it can also be asserted with equal truth that for any such production in a given locality the use of charcoal as fuel would be eqnally unjustifiable. It appears to have been forgotten that there were other manufactures besides iron in which large amounts of charcoal were used, but these consumers seen] to have been guided entirely by the results of the experiments of the iron men, who necessarily made the largest qnantity of it. Some authors speak in a doubtful way of the quality of the charcoal produced, and a few concede that with great care good charcoal can he made in kilns, but that most of the workmen do not like kiln 'charcoal. This is the real secret of the opposition to this method of manufacture. Most of these objections were written when charcoal was the most important fuel used by the iron manufacturer, and when what was a largeproduction of iron for several furnaces was less than that produced by a single modern one, in localities where other fuels can be had. Almost all that has been written on the subject related to the use of the fuel for the manufacture of iron in the blast furnace, where very peculiar properties are required, and where the qnantity produced is limited by the height of the furnace, and this in turn by the crushing resistance of the charcoal. A large production was, therefore, only possible when the best and hardest woods were used. Of all these objections there is not a single one which is not eqnally applicable to any method of charcoal manufacture, whether it be meilers, pits, or furnaces. Until recently, therefore, the manufacturers of charcoal iron

Jan 1, 1880

By Vasily P. Muravjev, Gennady I. Razgildeev

The theory of reliability is a powerful mathematical tool for determining optimum selection of components and application of electrical power to coal mines. In order to make this tool useful, statistical material on equipment life must be gathered and all failures carefully recorded. Statistical data can be applied to new apparatus design and can be used to determine optimum configuration of network and maintenance to reduce costs. Reference is made to underground power systems in the USSR. Technical progress in the last few years has occurred in the design and application of highly productive coal mining and transporting machinery. One of the most important problems facing mining engineers is to increase the availability of the machine to obtain higher productivity. However, machine failures and breakdowns of electrical power supply components cause serious delays in the coal-winning processes. In spite of the fact that electrical equipment and the power supply contribute only a small percentage of direct mine costs, electrical failures as well as power supply delays can result in severe indirect losses. It is necessary, therefore, to consider reliability and safety in the application of electrical equipment underground. To obtain the best results, it is necessary to investigate and evaluate the reliability of the electrical mining components (starters, breakers, motors, cables, etc.) and optimal methods for minimizing maintenance, the desired result being equipment which is efficient and safe. Electrical equipment reliability directly influences economics: the lower the reliability the more frequently failures occur, causing serious working delays and possibly huge economic losses. By the same token, while increasing the number of preventive maintenance calls per unit time might result in fewer failures, thus reducing delays, the cost of making more frequent maintenance inspections will increase; this is one aspect to be discussed in detail. Obviously, failures of identical types of electrical equipment (starters with the same current and voltage, etc.) are influenced variably by different working conditions, environments, quality of the apparatus, maintenance procedures (personnel, frequency, quality), load, and other factors. Hence, the lifetime of identical types of equipment will vary depending upon usage in terms of the foregoing factors. Thus for a given type of electrical component, these factors must be considered quantitatively; the interaction of all these factors are evaluated quantitatively by a statistical method using probability theory. Equipment reliability must be quantitatively determined from a study of equipment life, since no one laboratory test can reproduce all working conditions and environmental effects. Nevertheless, reliability theory applied to electrical mining equipment is a very powerful mathematical tool for selecting as well as evaluating certain parameters. It is necessary to select several reliability parameters so that one can obtain an expression for the total overall economic situation in terms of cost, taking into consideration damage caused by electrical equipment failure and cost of maintenance. To accomplish this result, such characteristics as apparatus lifetime, breakdown idle time, and losses (damages) can be determined quantitatively on a statistical basis. For identical electrical equipment working under similar conditions, the previously mentioned reliability factors are random variables and therefore can be characterized readily by a probability density function. Investigations carried out by the authors in the Kuznetsk Basin (Kuzbas) in West Siberia, USSR, show that the reliability factors of electrical mining equipment are well described by the exponential, normal, or Erlang's distribution in most cases. Mining electrical equipment life is well-described by the exponential law. The distribution of lifetime density is

Jan 1, 1971

By William F. Butler, Mo-Hung Che

DEVELOPMENT OF MONEY AND MONEY STANDARDS This chapter is concerned with the rise, and then the decline and fall, of gold and silver as monetary metals. As a first step in tracing the history of this process, it is necessary to consider the nature of money, and the manner in which different forms of money have developed over the centuries. The origins of money go back into deepest antiquity. Once men ceased to be pure nomads and entered into even a rudimentary form of society such as clans or tribes, money had to be invented The first step was barter as farmers or hunters swapped their surplus products for things produced by artisans such as shoes, clothing, and simple tools. But such barter trading is inconvenient even in primative societies It is difficult to match up buyer and seller at any point in time There are problems in arriving at viable and acceptable terms of exchange. The accumulation of savings-wealth-is complicated. No one can be sure that a pile of furs, or wheat, or certainly fish or game can be used in the future to trade for other goods or services. So even prehistoric man saw the need for money. There was a need first for something to serve as a medium of exchange This was an essential first step in the process of specialization-or the division of labor. A farmer, a hunter, or a shoemaker could only devote his full efforts to his trade if he could be sure that he could exchange his surplus production for the other things he needed for existence. This required a medium of exchange-a form of money which would be broadly acceptable. Money was needed for two other reasons Some system of market prices was essential to facilitate the exchange of goods and services. This required some form of common denominator-some standard of value-to govern the exchange process. And there was also need for something to serve as a store of value, a place to put any excess production (savings) with the assurance that it can be used in the future to acquire a general range of goods and services. As a result, money, in one form or another, developed at a very early state in civilization. Yet the centuries have been marked by a search for a form of money which will possess in full measure all of the attributes in money-a reliable and universally acceptable medium of exchange, standard of value, and store of value. -A wide variety of things have been used as money at one time or another: shells, beads, stones, feather, metals, and even the teeth of sharks and dogs. Some of these things were obviously of little or no practical value. They were used because people had confidence in their continued acceptance as a medium of exchange. As the world evolved and as trading ex-

Jan 1, 1976

By Erhard Hornbogen

Twins were propagated into large, well-annealed crystals of a, iron-phosphorous and a, iron-molybdenum solid solutions. Strain fields caused by interaction of these twins were made visible by precipitation. These strain fields can be explained by assuming that transmitted and reflected plastic waves are created when a twin strikes an obstacle with high velocity. The twin front itself can be regarded as a shear wave that may be able to develop a one-dimensional shock front. The occurrence of {WO} fracture by the reflected stress is also discussed. The described effects were not found when twins propagated at lout velocity into disturbed crystals, for example, into crystals previously deformed by slip. DEFORMATION twinning leads to shearing of a crystal lattice under external load. The shear appears to be homogeneous over a large number of crystal layers. In a iron, shear occurs on the (112) planes and in the <1ll> directions. The formation of a twin proceeds by the movement of partial dislocations that change the stacking at the twinning plane.l, In the bcc lattice, this partial dislocation can be created by dissociation of a sessile a/2[111] dislocation that lies in the (112) plane: Cottrell and Bilby&apos;s spiral mechanism can explain the homogeneous shear, but has not been proven experimentally. Nevertheless, this mechanism can explain the possible high velocity of formation of a twin. In Cottrell and Bilby&apos;s model, as in other models of twinning or phase transformation, a much higher energy is required to spread the first stacking fault than to add new layers by further movement of the partial dislocations. The dislocations will therefore become accelerated proportional to the difference between the stress, tN, to nucleate and tp to propagate the twin. It has been assumed3,4 that tn is the stress required to make two partial dislocations of apposite sign pass for the first time. After the first layer of new stacking has been formed, the maximum stress is TN=Gb/4pd where G is the shear modulus, b is the Burgers vector of the partial dislocation, and d is their perpendicular spacing so that the amount of shear is S = b/d. From this formula, a value of 25 kg per mm2 has been estimated for twinning in Zn3. The measured values are smaller, but local internal stresses may help to provide the necessary stress. For a iron, a higher value can be expected, mainly due to the higher value of G. That agrees with the observation that "burst" twinning occurs if the yield strength is in-

Jan 1, 1962

By Oliver C. Ralston

A definite field of usefulness has developed for the brine-leaching processes of removing lead from ores and other products, so this paper reviews the developments, both in practice and in research, that have taken place since the publication of two earlier papers on this subject.&apos; Several commercial plants are now in operation and a number of semi-commercial test plants have been operated in an effort to determine the limitations of brine leaching and to compare the results with other forms of treatment. Briefly, the brine leaching of lead depends on the fact that lead chloride and lead sulfate are soluble in saturated sodium-chloride solutions. In dilute brines, the solubility of the lead salt is less than in pure water; but in the strong brines, the solubility is greater than in pure water due, supposedly, to the formation of a double sodium-lead chloride. This is seen in Fig. 1, which shows the results of M. Demassieux2 on the solubility of lead chloride in sodium-chloride solutions of different concentrations and at three temperatures. The curves are not those given by Demassieux but are calculated from his results in order to convert them to units common in metallurgical work. The right-hand branch of each curve shows that if the solution is kept in contact with solid sodium chloride the lead chloride can be almost entirely displaced from solution, but that brines which are saturated with sodium chloride, but are not in contact with the solid salt, have a very high solubility for lead chloride. The diagram gives the analysis of the solution in grams of lead per liter, although the substance actually in solution is lead chloride. At 100" C. as much as 100 gm. of lead per liter can be obtained; but at lower tem-

Jan 1, 1924

By R. Y. Williams

In the United States, fully 98 per cent. of the anthracite and bituminous coal tonnage obtained from underground operations is mined by the room-and-pillar system. Under this system, the total cost of the coal f. o. b. railroad cars contains as its greatest single item the money paid for "labor." Each labor dollar in an average bituminous mine may be subdivided into 85 c. paid for work done inby the gathering turnouts (including all work at the face), and 15 c. outby that point (including all work in and under the tipple). In an average anthracite mine, the corresponding figures are 70 c. and 30 c., the larger breaker force accounting mainly for the difference between these and the bituminous figures. The next largest single item after "labor" is usually "supplies and power;" and a division of this item inby and outby the gathering turnouts shows somewhat the same relative proportions as has been noted under the case of "labor". During the past 10 years, the chief advances made in the coal industry have been to obtain economies through complete mechanization covering that portion of the work which lies outby the gathering turnouts. These results have been accomplished by applying scientific principles to railroad yard layout, to cleaning and sizing machinery, to dumping facilities, to roller-bearing haulage equipment, and to heavy-rail, well-ballasted trackage. But these improvements, while gratifying in their resulting economies, apply only to 15 to 30 per cent. of the important cost items. Obviously, then, the big problem before the engineers of the coal industry today has to do with the methods of mining and the layout inby the gathering turnouts. Four years ago, Weston Dodson & Co., Inc., determined to have an exhaustive study made of the conditions which must be met in order to gain complete face mechanization, and in order that such a mining layout would be based on correct underlying principles. The result of that study, which was made by the writer, led to the adoption of a method of longwall mining wherein the roof is worked on the caving system and is supported as an overhang along the face by steel jacks.

Jan 1, 1928

By W. J. Reagan

THE problem of increasing output and decreasing percentage of rejections is a vital one in the manufacture of steel of any kind. The making of basic open-hearth steel for use in rolled steel wheels, tires for locomotive and car wheels, and forgings of various kinds, is a highly specialized industry. The increase in weight of railway rolling stock of all kinds, and the high speed that the public demands of transportation facilities, make it imperative that steel for use in this class of material shall be of the highest quality obtainable. During the past few years it has been the writer&apos;s good fortune to have opportunity-to study the defects in basic open-hearth steel, and also the results obtained by various changes in open-hearth practice, on such defects. The opportunity for study and the details available are rarely found in the manufacture of steel of any kind. It seems reasonable to assume that many of the results determined here can be applied to the production of steel of other types with a decided improvement in quality, a decrease in the percentage of rejections and an increase in output. All of the material described is basic open-hearth steel with the following range of analysis: carbon, 0.50 to 0.85 per cent.; phosphorus and sulfur, 0.04 coax.; silicon, 0.15 to 0.35; manganese, 0.50 to 0.75. All of this material is bottom-cast, therefore tapping and pouring temperatures are higher than in top-cast production. Ingots used in this type of work are of standard length with varying diameters. The ingot is known as duodecagonal, or twelve-sided. The standard body length is 88 in. and the hot top length, 14 in. Fig. 1 shows a typical ingot of this type. The diameter varies from 13 to 30 in. Ingots for special forgings, which cannot be made in molds of standard size, are made in molds of various sizes and designs. These ingots are sliced cold, into blocks of various lengths, depending upon the weight of the forging to be made. Fig. 2 shows the ingot-after coming from the slicing lathe. Just sufficient metal remains between blocks to hold the ingot in one piece while it is being removed from the lathe; then steel wedges are inserted between the blocks and the blocks are broken apart. This affords abundant opportunity for inspection, as the interior of the

Jan 1, 1930

By James Herbert Bartlett

The MANUFACTURE of Iron in the PROVINCE of Quebec. The St. Maurice Forges.—The deposits of iron-ore in the St. Maurice district, in the rear of Three Rivers, were probably known to the Indians and .Jesuits, but it is not till 1667 that any discovery is reported. The affairs of the colony were then in the control of the " West India Company," who amongst other monopolies had a right to all mines and minerals." Specimens of the iron-ore were examined in Quebec. in 1668 by the Sieur la Potardière, who reported unfavorably on them. In 1671, Louis de Buade, Comte de Frontenac, was appointed governor of La Nouvelle France ; and in the original manuscripts relating to his administration some allusion is occasionally found to the St. Maurice iron mines.? In a letter to the Imperial Government, dated 2d November, 1672, he says: "The iron mine of which I have already spoken is of great consequence. I have visited it myself, in order that I may be enabled to give a more accurate account of its nature. I am gratified to learn that another mine has been discovered in Champlain, which is much richer than the Cap de la Madelaine mine, and the ore is in greater

Jan 1, 1886

By Robert Henderson

SEVERAL very interesting articles have been written on the caving system of mining, but most of these papers have dealt separately with the slusher system or the chute and grizzly system. In this paper, a comparison will be made of the two methods, both of which are being used at the Climax mine. The mine is on the Continental Divide, in central Colorado, at an altitude of approximately 11,500 ft. above sea level. The long, cold winters, characteristic of the high Rockies, create a number of operating problems not usually found in other mining areas. THE ORE BODY The Climax ore body is just east of the Mosquito fault. This structural deformation has brought the granite on the east against the sedimentary rocks on the west. The ore occurs in an intensely altered granite and schist around a silicified granite core. The ore is in a highly fractured zone of moderate silicification. The principal mineral, molybdenite, is found in these fractures. Barren dikes of granite porphyry cut through the ore body and core with no apparent regularity. The grade of the ore is fairly uniform and gradually decreases toward the footwall core and also into the hanging-wall granite. The footwall and hanging wall are determined entirely by assays. The ore body is roughly dome-shaped, with the apex truncated at the surface. It is covered to varying depths with talus. A horizontal section of the ore body on the Phillipson level appears as an annular ellipse surrounding the footwall core. The ring of ore varies in width from 300 ft. to as much as 800 ft. The north-south axis of the core is about 1200 ft. and the east-west axis is about 1800 ft. In the ore zone, the rock is sufficiently strong to maintain reasonably large openings, and openings larger than haulage drifts usually have to be supported. The ore is cut by a great many fractures and shears and breaks into rather large blocks when caved, necessitating considerable secondary blasting. The waste that overlies the ore body breaks relatively fine in comparison with the size of the blocks of the caved ore and tends to run through the broken ore in the cave, causing dilution unless the draw is carefully controlled. MINING SYSTEMS For several years the ore was mined by the chute and grizzly system, a system that differs from that used in other caving mines only in the size of openings and equipment. In the chute and grizzly system, main haulage laterals were driven along the footwall core and also along the

Jan 1, 1944