Search Documents

By D. Harker, E. Epremian

The constitution of the nickel-tungsten system has been studied by a number of investigators, the most recent of which are Ellinger and Sykes.1 On the basis of metallography, electrical resistivity and hardness measurements and some X ray diffraction work, they constructed a consitution diagram (Fig 1). Ellinger and Sykes report a0 for the alpha face-centered cubic phase (nickel saturated with tungsten) as 3.66?.‡ The gamma phase (tungsten saturated with nickel) is given as body-centered cubic, but no value of a. is recorded. At 43 pct tungsten by weight (approximately 20 at. pct) a beta phase is reported, but structure and lattice parameter are not known. Primarily on the basis of metallographic evidence, they conclude that beta is a new phase and rule out the possibility of formation of a superlattice since they- observe a new phase in the microstructure. Grube and Schlecht2 report an ordering reaction in a system similar to the Ni-W (Ni-Mo) and Harker3 has shown that NirMo forms a superlattice upon the pre-existing face-centered cubic lattice of the alpha phase. Elliniger arid Sykes observed a change in the diffraction pattern of a 4.3 pct W alloy upon aging and attributed it to the formation of a new phase. Thus, there appears to be some question as to the character of the beta phase reported by Ellinger and Sykes. The purpose of the present work is to determine precisely the structure and nature of the beta phase in the Ni-w system of X ray diffraction methods. Experimental Procedure One inch diameter ingots of 43.66 pct, 40.15 pct and 34.06 pct .tungsten by weight (19.8, 17.6 and 14.1 at. pct respectively) were melted and cast under vacuum from electrolytic nickel and pure wire filament grade tungsten. The ingots were soaked for 16 hr at 1300°C in a hydrogen atmosphere furnace, then swaged at this temperature and finally drawn to 0.020 in. diam wire. Some of the bar stock was retained in 1/2 in. diam rod for hardness and metallographic studies. Wire samples for diffraction work were sealed in evacuated quartz tubes and subjected to the various solution and aging heat treatments in a hydrogen furnace. X ray photograms were taken in a Debeye-Slierrer camera using copper K radiation filtered by nickel foil. Results X RAY DIFFRACTION The lattice parameters of the alpha and gamma phases at saturation were determined by an X ray photogram of the 19.8 at. pct W alloy after solution heat treatment at a temperature well within the alpha-gamma range above the peritectoid temperature (17 hr at 1150°C—oil quenched). The alpha phase was found to be face-centeted cubic with a. of 3.594 ± 0.001?, while the gamma phase was determined as body-centered cubic with a. of 3.158 ± 0.001?. Exactly the same phases and parameters were ohtained with the 17.6 at. pct W alloy for the same solution heat treatment. Thorough analysis was made of an X ray photogram of a 19.8 at. pct alloy sample in the quenched and aged condition (solution treated 1T hr at

Jan 1, 1950

By Lucien Eaton

VENTILATION in the iron mines of the Lake Superior region in nearly all cases is natural; that is, it is induced by the difference in elevation between different outlets in the mine and by the difference in temperature of the air in the mine and that outside. This difference in temperature is frequently augmented by placing a steampipe in the upcast shaft; but aside from this, artificial aids to ventilation have been rare until - recent years. In some of the older mines, as at the Cliffs Shaft mine at Ishpeming, Mich., in the 80's, fans have been used when there was only one opening to surface, but their use was abandoned as soon as a natural circulation of air started. In recent years, the Newport mine at Ironwood, Mich., was the first to use positive mechanical ventilation. The installation was not large enough, however, to give definite results, reliance being placed largely on natural ventilation. With the coming of warm weather in the spring of 1914, the necessity of positive mechanical ventilation at the Lake mine of the Cleveland-Cliffs Iron Co. at Ishpeming, Mich., became evident. The workings of the Lake mine are under the bed of old Lake Angeline, which was pumped out in 1894, and the mine had been in operation for 6 years prior to that date making a total of 26 years of continuous operation. The total production, up to 1914, amounted to over 8,000,000 tons. The ore was first mined by square-set rooms and pillars, but this was later changed to top slicing and caving. Both methods required the use of large amounts of timber, probably 80,000,000 board feet in all, practically all of which remained in the timber mat. The slow oxidation of this timber was one of the principal causes leading to the installation of mechanical ventilation. The mine was served by only one working shaft, called No. 4, a second outlet being provided by a raise to the surface from the old workings on the south side of the mine. This raise was the "down cast;" but it was very small and the drifts and raises leading to it were too small and crooked to permit an adequate amount of air to enter the mine, especially during the warmer weather. Measure-

Jan 8, 1920

By W. H. Bassett, C. H. Davis

The late J. P. Sparrow, chief operating engineer of the New York Edison CO., carried out a series of practical tests on condenser tubes of several copper alloys and reported on the results to the Association of Edison Illuminating Companies at its meeting in September, 1913. In the preparation of these tubes the senior author had the pleasure of cooperating. Copper-zinc alloys in the proportions of 60-40,70-30,80-20, 90-10, and Admiralty metal, which is in effect 70-30 with 1 per cent. of tin, were tried. Monel metal and several copper-nickel alloys, and 8, 5, and 3 per cent. aluminum bronze were also tried. At the time of this report, the aluminum bronze had been in service for 4 1/2 years and seemed to be giving especially good results but later it began to fail and showed no substantial improvement over Admiralty metal. Monel metal was unsatisfactory and the nickel alloys apparently did not give better service than the Admiralty alloy. Previous to the publication of the report, and after considerable discussion, it was agreed that a test where tubes of different kinds could be under laboratory observation would be advisable, so the apparatus described here was set up in The American Brass Co.'s Waterbury Laboratory. This was fitted with tubes of copper, brass, bronze, nickel silver, cupro-nickel and other alloys, and the test started on Oct. 11, 1912. Salt water from East River, New York harbor, was barrelled and transported to the laboratory for the test. A fresh supply, completely replacing the water in service, was obtained at the end of each six months period. Plan of Procedure In general, the procedure was to inspect the tubes at short intervals and to remove those that had begun to leak. The tubes removed were carefully examined and a photographic and microscopic record of the

Jan 1, 1925

By H. W. McQuaid, E. W. Ehn

It is usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effeet of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide call result in total unfit-ness of low-carbon steel for case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 1, 1922

By H. W. McQuaid, E. W. Ehn

It is usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effeet of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide call result in total unfit-ness of low-carbon steel for case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 1, 1922

By H. J. R. Way

THE work to be described was undertaken at various periods from 1937 to 1939 on the Busia gold field, in the eastern province of Uganda. It was decided to examine the possibility of reef prospection by the resistivity method, for it was not known how far the usually disintegrated nature of most reefs in the ubiquitous laterite near the surface would obscure indications obtained by resistivity traverses. The work at the commencement was therefore largely experimental, but the results obtained thereby were satisfactory, and a survey was started at the Government closed area at Amonikakine. With the limited time and resources at the writer's disposal, it was not possible to complete the survey to his satisfaction or to follow up exhaustively all the geophysical indications, but some of the results of the experimental work and the survey were of sufficient interest to be worth recording; in particular the relation between the width of reef, electrode separation and shape of the curve, and the interference effect of constant separation curves over zones of float are significant and useful. Three new veins were located, but only one contained sufficient gold to warrant detailed prospection. This was called the Geophysical reef, and was uncovered over a strike distance of 1140 ft., and there are indications that it extends over a distance of 1990 ft. These results and the recommendations consequent therefrom were embodied in a special report to the Uganda Geological Survey. HISTORY OF THE FIELD The Busia field is in the southeastern corner of Uganda near the Kenya-Uganda border, and is about 17 miles north of the northeastern corner of Lake Victoria. Gold was first discovered in the area in the stream beds by Davies1,2 in 1932. Subsequently numerous small alluvial claims were worked by prospectors and the area was prospected for reef by a company for periods varying from three to nine months, but was finally abandoned, as the results were considered unfavorable. Further prospecting by the Geological Survey in 1935-1936 under Davies3 and later under the writer4 uncovered three reefs with sufficient gold values to be of economic interest. These were finally taken over by a company known as Borderland Syndicate, which still owns the area, and from September 1937 to the end of 1941 about 13,000 oz. of gold was extracted from reefs of the area proved by the Geological Survey. Opencast mining operations are still proceeding (February 1943). The Amonikakine area lies to the immediate north of that of Borderland Syndicate. A certain amount of prospecting had been done when the writer started work there. As a result of his report, this area was taken over by another syndicate, but little further work was accomplished before it ceased operating because of difficulties of wartime working.

Jan 1, 1944

By Linn M. Farish

SOVIET RUSSIA reserves must be stupendous. In 1937 I. M. Goubkin placed the reserves of all categories it approximately 48 billion barren which was about twenty billion horn Is in excel:, of all the oil produced in the world since 1857. It is not unlikely in fact it is probable, that these huge stores of petroleum may ultimately be proven to exist within the present boundaries of the U.S.S.R. The size of the country is almost beyond imagination it is 2.7 times as big as the United States. Great sedimentary basins exist in all its different geological provinces, much of which are entirely untested and barely prospected. Oil in commercial quantities is actually produced from formations in every period from the Devonian to the Pleistocene. In the Emba region alone, 300 salt domes are known with an estimate of 700 still to be found. Only 22 of the 300 have been drilled and all showed oil. Of the 22 domes drilled six are now producing. There are 400 mapped structures reported in Azerbaijan

Jan 1, 1940

By L. Weaver

THE Tennessee Copper Co.'s mines are in the southeast corner of the state of Tennessee, Polk Co., in the well-known Ducktown copper basin. Their new circular production shaft will eventually be the only ore hoisting shaft, and is located for handling ore from Boyd, Calloway, Mary, and Cherokee mines. A circular, rather than a rectangular, shaft was decided upon because: 1-The circular shaft section is stronger when lined with concrete. Reinforcing steel was not required, thus reducing lining cost by one- quarter. 2-Water sealing was desired; it was thought it could best be done with a concrete lining followed by pressure grouting to eliminate water seeps. 3-The shaft labor saving equipment could best be used in a large opening, so the round section was made for economy, sinking, mucking, concreting and water sealing. Less shaft steel is used than could have been possible with steel sets. There are no posts required; center beams and Tee plate assembly placed at 10 ft hold the 100 lb steel guide rails.

Jan 1, 1950

By D. S. Tomalin, D. F. Stein

The effect of reducing oxygen to low concentrations on the fracture of high-purity iron single crystals has been examined at 78° and 20°K. It is found that iron single crystals grown by the strain-anneal method usually contain a few occluded grain boundaries which may become embittled in the presence of oxygen, thereby nucleating cleavage fractures. High purity with respect to interstitial elements was found to inhibit twinning and evidence is presented for an orientation dependence of the resolved yield stress. Deformation occurred by slip rather than twinning at both temperatures of testing with elongations of as much as 9 pct at 20°K. THE fracture properties of iron single crystals have been observedl-3 to be a function of temperature, orientation, and purity. Allen, Hopkins, and McLennan1 demonstrated that at 78°K iron single crystals became increasingly brittle as the tensile axis approached the (001) pole of the stereographic unit triangle. Iron crystals with the tension axis near a (001) pole were completely brittle and orientations near the (011)-(111) boundary were very ductile, achieving a 100 pct reduction in area prior to fracture. Later work of Biggs and pratt2 and of Edmondson3 demonstrated that by reducing the carbon content of the single crystals the transition between brittle and ductile failure at 78°K could be shifted to orientations nearer the (001) pole. Ed-mondson went further and pointed out that any mechanism which tended to increase the yield strength of the iron (i.e., carbon addition, pre-strain) also increased the tendency for brittle behavior at 78°K. Thus by a reduction of carbon content Biggs and Pratt were able to obtain ductile behavior to within 20 deg of the (001) pole, and Ed-mondson was able to obtain ductile behavior to within 26 deg of the (001) pole. Edmondson's material had a total interstitial content (carbon, oxygen, and nitrogen) of approximately 60 ppm and, although Biggs and Pratt reported no analysis, indications were that their iron contained comparable impurities. Stein, Low, and seybolt4 purified iron single crystals to a total carbon, oxygen, and nitrogen content of approximately 20 ppm. They observed a lowering of the yield stress with this increased purity, and thus one might have expected an observation of increased ductility. Although they tested specimens of orientations which the previous workers had indicated should be ductile, the crystals failed at a 78°K in a brittle manner with little elongation. Stein noted,' however, that about 90 pet of the failures could be traced in origin to occluded grains. Allen et al.1 and Edmondson3 do not report examination of their cleavage surfaces, but Biggs and pratt2 reported that microscopic examination of the cleavage surfaces of many of their specimens revealed the presence of small occluded grains. Honda and cohen6 and Keh7 have also observed the initiation of fracture at occluded grains in iron single crystals. Therefore, the additional complication of occluded grains must be considered in studying the properties of iron single crystals and the origin of fractures determined if the ductility exhibited by the crystals is to be considered meaningful. Various investigators8-12 have studied the effects of impurities on grain boundaries in high-purity polycrystalline iron. Rees and Hopkins10 showed that the addition of oxygen to low-carbon (0.002 pet) iron weakened the grain boundaries, causing a shift from transcrystalline to intercrystalline fracture and a progressive decrease on the brittle-fracture stress with increasing oxygen content. In addition, it has been shown by Low and Feustel11 that the addition of carbon to polycrystalline iron containing oxygen eliminated grain boundary brittleness. Thus, oxygen can embrittle grain boundaries in high-purity polycrystalline iron, but the addition of an appropriate amount of carbon can eliminate the oxygen-induced brittleness. The oxygen content (19 ppm) of the iron "single crystals" employed by Stein el al. was large enough to suspect impurity effects at the occluded grain boundaries. Allen et al.1 Biggs and pratt,2 and Edmondson3 may have masked any occluded grain problem in their specimens considering the relatively high carbon levels they employed. stein13 demonstrated that the addition of as little as 0.9 ppm C to previously purified (less than 5 x 10-3 ppm C) "single crystals" would increase the elongation from a few percent to more than 20 pet at 78°K and the fracture was not associated with grade boundary initiation.

Jan 1, 1965

By Arthur Bell

(San Francisco Meeting, September, 1915) . PRIOR to 1908 the oil production in the State of California, had been almost entirely a heavy fuel, oil, with a high flash point, hut changed within a-short period to a large percentage of refining oil with a low flash, by reason of the coming in of the Santa Maria field, the Midway field, and the increased production of the Fullerton field. This is clearly shown in the following tabulation of California's production: Year Barrels . Below -20° Be, Above 20° Be,, Per Cent_ Per Cent. 1905 48,307,000 90 10 1910 77,698,000 SO 20 1912 90,075,000 6o 31 1914 10:3,600,000 47 53 The bringing in of these high percentage's of light oil with their dangerous low flash and the increasing demand for the refined products necessitated the devising of some cheap and efficient means of quickly separating the lighter elements either in the field or at the main distributing points; also it became necessary to remove the excessive percentage of water which many of the light oils carried in emulsion.

Jan 9, 1915

By L. C. Graton

I. INTRODUCTION. The Relations of Scale in Geologic Work. MANY features of human accomplishment rest upon the possibility of representing natural objects on a scale of different magnitude from the actual one. Most drawings, for example, are of very different scale from that of the object depicted, and indeed are useful mainly on this account. More important than the question of mere convenience, however, is that of meeting the physical limitations of vision.1 Thus, a mural

Jan 5, 1913

By George M. Fowler, Joseph P. Lyden

PaGE Scope of this Report.................................................... 206 Production of Tri-State District.......................................... 207 Historical Sketch....................................................... 207 Location and Topography............................................... 211 Geology............................................................... 212 The Tri-State District.............................................. 214 Stratigraphy........................................................... 217 General Geological Section in Tri-State Region....................... 217 Stratigraphic Section of Mineralized part of Boone Formation........... 218 Stratigraphic Section Bird Dog Well.................................. 219 Metamorphism........................................................ 220 Structure............................................................. 225 Regional.......................................................... 225 Due to Metamorphism.............................................. 229 Ore Deposits.......................................................... 231 Types............................................................ 232 Hard-ground Deposits.......................................... 232 Brecciated................................................. 232 Stratified............................................ 232 Sheet Ground............................................. 232 In Dolomite............................................... 233 In Shale.................................................. 233 Soft-ground Deposits.......................................... 233 In the District as a Whole....................................... 233 Ore Minerah and Analysis......................................... 233 Paragenesis....................................................... 234 Conclusions........................................................... 236 Structure.......................................................... 236 Genesis of the Ore.................................................. 237 Future of the District............................................... 239 Acknowledgments..................................................... 239 Discussion............................................................ 239 Scope of This Report The Tri-State district. as outlined in this paper. refers to the entire mineralized area in sout'hwestern Missouri. southeastern Kansas and

Jan 1, 1932

By R. L. Wiegel

The two questions considered in this study are: (1) what similarity is there in the liberation of magnetite from various iron formations, and (2) how is this liberation affected by the size reduction technique employed. Twelve sample suites were obtained from commercial concentrators processing magnetite iron formation in the United States, Canada, and Australia. These samples have grades in the range 15 to 45% magnetite iron and approximate mineral grain sizes o f 50 to 2000 microns. Efforts were directed at measuring the liberation characteristics of the samples obtained from the concentrators primary grinding mills. The Davis tube, a laboratory magnetic separator, was used to concentrate individual size fractions of the size reduction product to determine liberation data. These liberation data were compared with relationships calculated from a highly idealized mathematical model of liberation in a binary mineral system. The results of these comparisons have been encouraging for nine or ten of the twelve samples tested. This leads to the conclusion that for most commercial iron formations, at least with conventional rod mill size reduction, it is possible to quantitatively characterize liberation with two parameters: an effective mineral grain size and ore grade. Limited laboratory size reduction tests as well as one of two sets of liberation data from commercial primary autogenous grinding lend some support to the contention that autogenous grinding can affect mineral liberation.

Jan 1, 1976

By Stanley D. Michaelson, Norman Weiss

This was a year of realization. Some years are for planning and development, some for designing and building, others for fulfillment. With greater hopes and plans for the future than ever before, the year 1954, nevertheless, will be remembered principally because of project completion. Among copper mines, for example, there were Silver Bell, Copper Cities, Bisbee, Yerington, and White Pine. In iron, there were the Humboldt, Coleraine, Cerro Bolivar, and Eagle Mountain. In asbestos, Johns-Manville's new mill at Asbestos, Que. In uranium, completion of the ninth mill on the Colorado Plateau-Kerr-McGee's at Shiprock, N. M. In research, 1954 marked the completion of Kennecott's Research Center in Salt Lake City, one of the historic forward strides in the science of minerals beneficiation. The year was fruitful in other directions as well. Investigations of a fundamental nature were on the upswing, and pilot plant projects have also increased in size and number. Progress in new reagents and equipment was greater than normal. It can already be conservatively predicted-from the technological point of view-that 1955 and 1956 will be tremendous years.

Jan 3, 1955

By E. C. Wright

FOR many years the cost of making pig iron and steel in the Birmingham district has been about the lowest in the United States. The close proximity of the important raw materials such as coal, iron ore, limestone, and the large available scrap supply made it possible to assemble all of the important ingredients necessary for steel- making with only nominal costs for transportation. Both iron ore and coal were being mined in this district at one time for about $1 per ton from underground operations. At that time mining wages were low everywhere and the labor rate in the South was considerably below that of other mining districts. This situation persisted until the emergence of labor unions as an economic and political force, emigation of southern labor to northern plants, and continued growth of industry in the South in the years following the depression of 1932. Since that time union organizing of miners and steel workers throughout the nation has increased labor costs in mining and steelmaking. This influence has been felt particularly in underground mining operations since the proportion of labor cost to total cost is still high. The previous advantage in basic labor rate in the South has been almost entirely eliminated by the equalization of labor rates in basic industries by national unions. Since 1945 these influences have been especially noticeable in increasing the cost of mining coal and iron ore in the South. The northern steel districts are still being largely supplied with iron ore from the Minnesota open-pit mines and the cost of this ore has not increased nearly as much as the cost of ore obtained from underground mines in Birmingham. A similar situation exists in coal mining; the thinner seams in Alabama are not so amenable to mechanization as the northern mines and, as a result, the output per man-day in southern mines is only about three tons of coal as compared to five or six tons per man-day in the large captive mines of West Vir-

Jan 1, 1950

By A. Perry Thompson

I- GeneRal Distribution, AppeaRance, and Relations ........ 563 11. Data fRom MicRoscopic Examination............... 568 1. Criteria for Distinguishing Primary from Secondary Minerals...... 568 2. The Leonard Vein Filling..................... 574 Quartz............................ 575 Pyrite............................ 575 Enargite............................ 576 Covellite............................ 578 Bornite............................ 581 Chalcocite........................... 583 Chalcopyrite.......................... 586 3. The Fault-Vein Covellite..................... 587 The Speculator Ore........................ 587 The East Gray Rock Ore.....,.............. 589 4. Other Occurrences of Covellite.................. 591 111. Conclusions........................... 592 1. The Replacement of Minerals..................592 2. The Character of Mineralizing Solutions .............. 594 I. General Distribution, Appearance, and Relations Mining in Butte has seldom encountered covellite in commercial quantities. The notable occurrences, extending vertically and laterally perhaps several hundred feet, presented scattered, bladed lenses of this mineral in a matrix of quartz, pyrite, enargite, bornite, and chalcocite. But under the microscope covellite is seen to be widespread in the Butte ores, though in such small quantity that megascopic examination will not discover it. In early mining operations covellite was found in the Gray Rock vein, a member of the Blue vein system. As described by Sales,' it persisted as an occasional ore mineral, associated with quartz, pyrite, tetrahedrite, bornite, chalcocite, and minor amounts of sphalerite, from the 700-ft. to the 1,200-ft. level of the East Gray Rock and Diamond mines. Crushed quartz-monzonite and later quartz completed the vein filling between

Jan 1, 1916

By M. Bevis, A. F. Acton, P. C. Rowlands

Defor~nation twinning and transformation twinning modes most likely to be operative in Fe-Ni and Fe-Ni-C martensites have been determined using a new theory of the crystallography of deformation t~inning.~ This analysis shows that potentially important conventional and nonconventional twinning modes1 have been omitted in previous analyses. Discussion is given on the relevance of the predicted twinning modes to the lattice invariant shear associated with the martensite transformation in steels and to anomalous deformation twinning in Fe-Ni-C martensites. THE two most important criteria which appear to govern operative twinning modes in metallic structures1 are that the magnitude of the twinning shear should be small and that the twinning shear should restore the lattice or a multiple lattice in a twin orientation. The latter criterion ensures that the shuffle mechanism required to restore the structure in a twin orientation is simple. These criteria have been adhered to in the prediction of twinning modes2"6 in bcc and bct single-lattice structures with axial ratios in the range y = 1 to 1.09 as, for example, encountered in martensite occurring in steels. Refs. 2 and 3 in particular consider the martensite transformation in steels and the twinning modes in these cases relate to transformation twinning, and hence the lattice invariant shear associated with the martensite transformation. The list of twinning modes which can be compiled from these sources is incomplete and the ranges of magnitude of shear considered could be unrealistically small, particularly in the case of deformation twinning. The latter consideration is supported by the fact that twinning modes with magnitudes of shear large compared with the smallest shear consistent with a simple shuffle mechanism have been established in, for example, the single-lattice structure mercury7 and the multiple-lattice structure zirconium.&apos; In addition the anomalous deformation twins reported by Ftichrnan4 to occur in a range of Fe-Ni-C martensites still remain unexplained. It is clear that a comprehensive analysis of twinning modes likely to be operative in martensite In steels is required. The results of the application of a new theory of the crystallography of deformation twinningg to these structures are presented in this paper. The theory has been used to determine all shears which restore the lattice or a multiple lattice in a new orientation with magnitude of shear up to a required maximum. The orientation relationships between parent and twinned lattices are not restricted to the classical orientation relationships of reflection in the twin plane or a rotation of 180 deg about the shear direction. PREDICTED TWINNING MODES Twinning modes which restore all or one half of lattice points to their correct twin positions will be referred to as m = 1 and m = 2 modes, respectively. These modes are the most likely to describe operative modes in single lattice structures. The bcc m = 1 and m = 2 modes which have magnitudes of shear s in the range s < 2 and s < 1, respectively, have been given10 and are reproduced here in Tables I and 11. Detailed discussion of the crystallography of these modes and cubic modes in general will be discussed elsewhere (~evis and rocker, to be published). The four twinning elements Kl, &,ql,7)2 as well as the magnitude of shear s are given for each twinning mode, and the twinning modes are given in order of increasing shear. Two twinning modes are given in each row of the tables, the twinning mode Kl, Kz, ql, q2 and the reciprocal twinning mode with elements Kl = K,, Ki = Kl, q: = q2, and 17; = ql. The m = 1 and m = 2 twinning modes which describe twinning shears with small magnitudes of shear and simple shuffle mechanisms in bct crystals with -y = 1 to 1.09 are given in Tables I11 and IV, respectively. On increasing the symmetry of the tetragonal lattice to cubic, that is making y = 1, all modes listed in Tables 111 and IV must reduce to crystallographically equivalent variants of the modes given in Tables I and 11, respectively, or become twinning modes with both shear planes as symmetry planes in the cubic lattice and hence not considered in Tables I and 11. With the exception of this last type of mode only those tetragonal twinning modes which reduce to modes 1.1, 1.2, 2.1, and 2.2 of Tables I and I1 are considered in Tables 111 and IV. For values of y in the range -y = 1 to 1.09 the tetragonal modes and the corresponding cubic twinning modes have approximately the same magnitude of shear. The twinning modes listed in Tables 111 and IV are therefore by the criteria given above the most

Jan 1, 1969

IlAbad, Leopoldo F , Min Engr , Div of Mines, Bureau of Science, Manda, P I &apos;23 ||Abadilla, Quince, A , Cia Minera de Petrolco El Aguila, S A Box 86, Puerto Mexico, Ver , Mexico &apos;20 ||Abarquez, Ramon F , Met , Bureau of Science Manila, P I &apos;24 ||Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, Ohio &apos;21 Abbott, A N , Mines Supt, Mazapil Copper Co , Ltd Concepcion del Oro, Zac , Mexico &apos;23 Abbott, Clarence E , Gen&apos;l Supt , Iron Mines Div , Tenn Coal, Iron & R R Co , 1405 Minnesota Ave , Bessemer, Ala &apos;04 Abbott, Louis Benjamin, Chief Engr , Consolidation Coal Co , Elkhorn Div Jenkins, Ky &apos;15 Abbott, Robert R , Met Engr , Peerless Motor Car Co Cle veland, Ohio &apos;12 ||Abbott, Wells Osborn, Ray Consolidated Copper Co Hayden, Ariz &apos;23 Abeel, George H , Jr, Cons Min Engr 4612 W 17th St, Los Angeles, Cal &apos;18 Abel, Albert E, Asst to Pres, Valley Mould & Iron Corpn Sharpsville, Pa &apos;19 Abernathy, George Elmer, Prof Geol & Min , Kansas State Teachers College Pittsburg, Kans &apos;20 Abey, Hiroshi, Min & Met Engr, Takata & Co , 2 Yeirakucho, Nichome, ICojimachi-ku, - Tokyo, Japan &apos;17 ||Aborn, Robert H 24 Groveland St , Auburndale, Mass &apos;19 Abouchar, Sylvain Sley, Min Engr & Geol , Care of S H Sekaly, 13 Rue El Nimr, Cairo, Egypt &apos;17 ?Abraham, Arthur W 1626 N Alexandria Ave, Los Angeles, Cal &apos;21 Abrahams, Alexander I, Gen&apos;l Mgr, Ricon Electrical Co Slough, London, England &apos;13 ||Abrahamson, C Walter, Min Engr, Brule Min Co Stambaugh, Mich &apos;21 Abrams, Charles Jackson, Mill Supt, Utah Apex Min Co Bingham Canyon, Utah &apos;21 Abrams, David H, Cons Min Engr 182 Worth St, Johnstown, Pa &apos;20 ?Acker, E O&apos;C , Met 128 East Washington Lane, Germantown, Philadelphia, Pa &apos;86

Jan 1, 1923

By Lauren A. Wright, A. E. J. Engel

Under the designations "industrial talc" and "soapstone" are included earth materials of widely different chemical and mineral compositions. Talc, the mineral, is a hydrous magnesium silicate, with a suggested theoretical formula H2Mg3(SiO3)4 or H2O.3MgO.4SiO2, which postulates 63.5 pct SiO2, 31.7 pct MgO, and 4.8 pct H20.18 Single grains or leaves of talc, however, seem to have variations in water content that range from 3.5 pct to more than 7 pct, as well as slight differences in the proportions of MgO and Si02.20 Most of the industrial talcs produced in the United States do not approach the composition given above (see Table 1), but are essen- [ ]

Jan 1, 1960

By B. B. Gottsberger

IT SEEMS strange that so many years after the pas¬sage of the first acts requiring registration or licensing of engineers, so few members of the mining branch of the profession are aware of what has taken place. Laws regulating the practice of engineering have now been passed in 19 states of this country, and in many others, such legislation has been proposed. That such laws are necessary for the protection of life, health and property, as is stated in most of them, is doubted by many. That the standing of the engineering profession will be improved by them is certainlyy open to question. That such laws are a welcome addition to the regulation of business by governmental agency, is not likely to be a general opinion. That once more, and in spite of appeals to engineers to interest themselves in affairs of government, an active minority has succeeded in imposing its will on a passive majority, seems but too true. However, the laws are there and information regarding them should be of use and interest to those most directly concerned.

Jan 1, 1921