Search Documents

By S. E. Bronisz, Dana L. Douglass

a Uranium was deformed by cold rolling, and the effects of this plustic deformation on the microstruc-ture of the metal were observed by the technique of transmission elecbon microscopy. The recrystalli-zation of selected cold-wmked samples was also studied by this method. The samples were prepared for examination by electrolytic thinning in a standard metallographic electrolyte which has not been previously reported as being used in producing thin foils of uranium. The microstructural changes observed in the a uranium were generally similar to those seen by optical microscopy. The changes in the microstructure of a uranium following cold work and recrystallization treatments have been the subjects of several studies employing optical and X-ray techniques.12-19 These studies indicated that twinning was the redominant mode of deformation at room temperature20 and that the regions of high energy associated with the deformation twins were preferred sites for the initiation of recrystallization.15,18, Recently several workers have prepared thin foils of uranium suitable for examination by transmission electron microscopy.'-lo The foils thus prepared have been used to study fission fragment damage; a particular dislocation reaction,' and gas precipitation." At this laboratory the microstructural changes occurring during the cold working and recrystallizing of a uranium samples have been studied by using transmission electron-microscopy techniques. The foils used in this work were electrolytically thinned in a polishing bath not reported previously in the literature as being used for this purpose. EXPERIMENTAL PROCEDURE The uranium used in this investigation was depleted a uranium sheet 4 mils thick. The results of a spectrochemical analysis of this material are shown in Table I. The as-received uranium was cut into strips, 1 in. wide by 5 in. long, and annealed in vacuo at 600°C for 2-1/2 hr. The resulting microstructure consisted of relatively uniform, equiaxed grains having diameters of 10 to 50 p. Cold Working. The cold-worked samples were prepared by rolling several of the annealed uranium strips to various thicknesses. The strips were reduced 3.5 ± 0.5, 6.0 ± 0.6, 10.0 ± 0.5, 19.5 ± 1.0, and 28.5 ± 2.0 pct in thickness. It was not possible to achieve these reductions with a single pass through the rolling mill, so the strips were turned end for end during the rolling procedure. The cold-rolled strips were stored in dry ice until samples from them could be thinned and examined (within 24 hr after rolling). Annealing. The samples used in studying the re-crystallization behavior of a uranium were obtained by annealing sections of the strips which had been reduced 10.0 and 28.5 pct. These samples were sealed in evacuated Pyrex capsules and were annealed in a tube furnace at temperatures from 200" to 600°C and for times from 1/2 to 2 hr, see Table l. Thinning: The samples from the rolling and heat treatments were prepared for examination in the electron microscope by electropolishing in a bath composed of 25 g chromic acid, 133 ml glacial acetic acid, and 25 ml water. This electrolyte has been used and recommended for preparing specimens for optical metallography It was necessary to mask the edges of the sample with a stop-off paint in order to prevent preferential attack in these areas. The paint used was made by dissolving polystyrene in benzene. The electrolytic cell consisted of a cylindrical stainless-steel cathode placed in a beaker containing the electrolyte, with the sample as the anode positioned at the cell axis. The temperature of the electrolyte was held below 15°C by cooling with liquid

Jan 1, 1963

By O. W. Shimer, D. C. Helms, C. E. Brown

The early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. . The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 3½ million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20" to 90 and some are on the invert in many sharp folds and faults. Planning The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been . maintained. Locations of stripping areas are determined as follows: I. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness

Jan 1, 1944

By T. S. Mohibatsela, R. V. Ramani, C. V. Manula

The Mineral Engineering Department of The Pennsylvania State University has developed a suite of computer models for anthracite open pit mining (Fig. 1)1 Individual sub-systems have been developed to (a) interpolate geologic field data to obtain coal tonnages, waste volumes, and strip ratios; (b) simulate equipment performance on selected pit profiles to generate data required to choose coal and waste removal equipment; and (c) evaluate selected cost factors to determine either a rate of return for a specified selling price or vice-versa. This paper describes the application of two of these subsystems, namely, the Reserves Model (GEOL) and the Open Pit Materials Handling Simulator (OPMHS), and how these may be applied for the selection of equipment for a prime anthracite mining site.2

Jan 1, 1981

By O. W. Shimer, D. C. Helms, C. E. Brown

The early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 3½ million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20" to 90° and some are on the invert in many sharp folds and faults. Planning The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been maintained. Locations of stripping areas are determined as follows: I. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness and pitch of the beds.

Jan 1, 1946

By Donald L. Katz

THE Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July 1, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produces 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand' indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplification and generalizations are necessary to give the over-all picture in so short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, r, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City. Wilcox Secondary Recovery Association on Sept. 5;.1940. Some information is taken from a report to the Association by C. V. Sidwell on March 1, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." HISTORY OF WILCOX ZONE The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. 12.1 .4 and areal map of Fig. 2. The sand is of Ordivician age and is composed of well assorted, rounded' sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 was dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1937 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1941

By S. R. Dunbas, D. C. Jillson, E. A. Anderson

THE present work was undertaken to furnish information, lacking in the literature, on the deformation mechanisms active in pure titanium at room temperature. Since it was started, Rosi, Dube, and Alexander' have indicated that slip can occur in coarse-grained (2 to 6 mm diameter) titanium on the {1010} and {1011} planes and twinning can take place on the {1072}, (1122) and (1151) planes. Liu and Steinberg,' working with titanium flakes produced by fused salt electrolysis, found evidence of twinning on the {1032$, {1121), {1122}, (1123}, and (1154) planes. The crystals used in the present work were substantially longer (up to nearly 2 in. in length) and possibly purer. Production of Large Crystals It was the purpose of this part of the work to provide single crystal or large grain specimens for use in the deformation studies rather than to study the mechanism of crystal growth. Accordingly, all further exploratory studies on methods were abandoned when it was found that cold-rolled bars sealed in vacuo in individual Vycor tubes and given three or more cycles of 4 hr at 1200°C and three to five days at 850°C, gave large grains. Eighteen specimens about 0.2 in. square x 2 in. long yielded 33 useful grains, ranging from Va in. to nearly 2 in. in length, with an agreeably wide range of orientations, Fig. l. The 0.25 in. thick strip from which the starting specimens were cut had been reduced 67 pct on 18 in. diameter rolls from a scalped, hot-forged (959" to 1000°C), arc-melted, iodide titanium ingot. Thc bar was at room temperature, but the rolls were at 200°C. Reductions of about 0.03 in. per pass were used. The bar was cut into four segments, each of which was rolled in a somewhat different manner. No effect on the growth of large grains was noted. The composition of the titanium, determined on turnings from the ingot scalping operations, is given in Table I. The Rockwell A hardness of the ingot was 26. The standard starting specimens, about 1/4x1/4x2 in., were milled on all four sides, hand polished on 280 and 400 mesh emery papers, etched for 3 min in a 50 HF-50 glycerine solution, rinsed, and dried in alcohol and ether just before sealing them in Vycor tubes. The average specimen weight was 7.5 g, and the tube volume was 6.5 cc. A vacuum of less than 1 micron pressure was applied. The specimen tubes were placed in an evacuated Inconel muffle to minimize the danger of collapse of the glass tubes at temperature. In practice the specimens were first heated to 1200 °C for 4 hr and then transferred fairly quickly to an 850°C furnace where they were held for three to five days. This cycle was repeated at least three times before the specimens were cooled, removed from the tubes, lightly polished and etched on one surface for examinstion. Those in which large grains had not developed were resealed in Vycor and returned to the cycling. Satisfactory specimens (about one out of every four cycled) were polished with emery paper on all four side;, then metallographically polished using ctchinz between wheels to remove distorted metal and, finally, given a very light etch to reveal the grain boundaries. This was necessary because the surface was roughened by the sublimation of titanium under high temperature vacuum conditions. Specimens were identified by TiXl numbers using supplementary letters to designate specific grains.

Jan 1, 1954

By D. L. Katz

The Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July I, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produccs 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand1 indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplifications and generalizations are necessary to give the over-all picture in SO short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, 1, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City Wilcox Secondary Recovery Association on Sept. 5, 1940. Some information is taken from a report to the Association by C. V. Sidwell on March I, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." History of Wilcox Zone The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. I2,3,4 and areal map of Fig. 2. The sand is of Ordovician age and is composed of well assorted, rounded sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 as dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1037 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1942

By D. L. Katz

The Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July I, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produccs 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand1 indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplifications and generalizations are necessary to give the over-all picture in SO short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, 1, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City Wilcox Secondary Recovery Association on Sept. 5, 1940. Some information is taken from a report to the Association by C. V. Sidwell on March I, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." History of Wilcox Zone The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. I2,3,4 and areal map of Fig. 2. The sand is of Ordovician age and is composed of well assorted, rounded sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 as dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1037 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1942

By H. O. Hoffman, C. D. Demond

There are two methods of determining the fusibility or refractoriness of fire-clays, the theoretical and the experimental. In the former, conclusions are drawn from the chemical composition; in the latter, from the changes which the clay undergoes when subjeoted to intense heat. It is well to use both methods, beginning with the actual heat-test and explaining the results obtained from this by the help of the chemical analysis. In discussing the subject, however, it is better to reverse this order. I. The Theoretical Method.* Leaving out the hygroscopic and combined waters and any organic matter, as not directly affecting the fire-resisting property, the refractory constituents of fire-clay are alumina and silica, and the fluxing constituents magnesia, lime, soda, potash and ferric oxide. According to Bischof,† alumina is the least fusible component, and silica follows close upon it. If, however, a mixture of the two be heated, it will be found that its melting-point is much lower than that of alumina, as a silicate will then have been formed. The way in which silica affects the refractoriness of alumina has been strikingly presented by Seger 1 in a diagram reproduced in Fig. 1. The abscissæ represent the melting-points of Seger cones Nos. 26 to 36 (see p. 55); the ordinates, the relative amounts of alumina and

Jan 1, 1895

By George A. Miller

ALTHOUGH the Andean mountain belt, which contains almost all the metal deposits of the other South American nations, does not enter Brazil, this country is rich in mineral resources, for in area it accounts for half the continent and geologically it contains almost all of the Brazilian Shield. This great mass of ancient rocks has been relatively stable for a long time and forms a great area of plateaus and highlands interrupted only by the syncline which carries the Amazon River across it to the sea. Lowland Brazil - the great flood plains of the Amazon. Tocantins, Paraguay, and Parana Rivers-is of no interest to the miner, and in fact supports but a small proportion of the country's population. The highland area is divided into unequal parts by the Amazon River; the north half is underlain by the north lobe of the Brazilian Shield which extends into Venezuela as far as the Orinoco, and into the Guianas, and is known as the Guiana Highlands. Mineralization appears to have been weak in the Brazilian portion of these hills. In fact most of the ore deposits are to be found in the States of Minas Gerais and Bahia, although the neighboring states of Sao Paulo, Pernambuco, and Piauhy can also boast of some deposits. Goias and Matto Grosso are as yet incompletely prospected but are considered to contain reserves for the future.

Jan 1, 1945

By NEWTON B. KNOX

PERU, lying south of Ecuador and having common frontiers with Brazil, Chile, and Bolivia, includes over a thousand miles of the Andean mountains. The coastal plain is arid and narrow and the Amazonian jungle region is of interest only on account of its oil and gold placer possibilities. The mountain zone, however, here forms one of the world's most highly mineralized regions. The Peruvian Andes, like their Bolivian and Ecuadorian counterparts, form two distinct chains separated by the great Apurimac and Maralion valleys; but these rivers cut through the Eastern range to join the Amazon drainage, and the central valley is missing north of the passes thus formed by these rivers; the localities where the ranges are joined are aptly called knots. In addition, in central Peru, there exists a third range lying to the east of the first two and separated from them by the Urubamba and Huallaga Rivers. The Eastern range, however, is of little importance to the miner for few metal deposits are to be found therein except for the gold mineralization in the South. In general, deposition of metals in the Peruvian Andes accompanied igneous intrusions which invaded the folded Paleozoic and Mesozoic rocks during the Tertiary; thus the ore bodies are all typical of shallow or moderate depths.

Jan 1, 1945

By George A. Miller

AMERICANS like engines, but more than anything they like powerful engines, and next to that they want them quiet, silent, smooth; perhaps a slight purr might be permitted, but they must not knock. To provide a gasoline to fit all these requirements, American petroleum technologists have experimented for years, and mounting octane numbers of the gasolines the refiners have produced both before and during the war bear witness to their success. The question on everyone's mind now is what may we expect in the way of engine fuel in the postwar period? The gasoline drouth during the war rationing, the inconvenience of doing without a car were major annoyances to all motorists, but they put up with them pretty cheerfully for the most part. However, now that the war is over, and the jalopies are all out and the better cars have been taken off the jacks and brought out on the road, the call is for "Some of that good gas-fill her up, if you please."

Jan 1, 1945

The high-grade orebody at Miami was mined successively by top-slicing, shrinkage, stoping and under caving. The method described in this paper was developed to enable the low-grade orebody (36,000,000 tons assaying 1.06 per cent copper) to be mined at a low cost without further dilution of the grade. The method is clearly described and illustrated by drawings and photographs, and the original paper should be consulted as it is impracticable to abstract it, beyond noting that the mining cost is just under 40 cents per ton and the average grade of ore now being produced yields less copper than the mill tailing of 1915, the tons mined per day having increased from 4000 to 18,000 in the same period. Vertical and Incline Shaft Sinking at North Star Mine By Arthur B. Foote, Grass Valley, Calif. (Tech. Pub. No. 324: Class A. Metal Mining, No. 36) THE main shaft of the North Star mine is an inclined one following the main vein at an average dip of 26 deg., a vertical shaft intersects it at the 4000-ft. (incline) level, the incline continuing to the 6300-ft. level. At this point the vein was found to give out and a new vein, called the No. 1, was found to dip in exactly the opposite direction.

Jan 1, 1930

By GEORGE O. SUMAN

IN THE operation of oil properties there are various difficulties with pumping wells which can often be overcome or greatly lessened if sufficient attention is, directed towards pump and tubing problems. The difficulties referred to are the wearing out of pumps, sanding up of pumps, and the sanding up of the hole. As the perforations in the oil strings are large and the oil and sand loose and unconsolidated considerable trouble is often encountered in pumping wells due to the ease with which' the sand can come into the holes. DETERMINING FLUID LEVEL In determining the proper depth at which to tube a well it is essential to first find out something about the behavior of the fluid in 'the hole: Facts in regard to this natter can be obtained by finding the fluid level on pulling the tubing, by making a pumping test on the well tubed to various depths, and by bailing tests during cleaning out work. In ordinary oil field operations it is customary to take the fluid level at the time of pulling the tubing. This 'can only be done when the pump is not sanded up. There are two methods used in obtaining the fluid level. One method is to note where the outside of the tubing starts, to be covered with fluid when pulling the

Jan 1, 1925

By R. W. Diamond

THREE mills are now operated by the Consolidated Mining & Smelting Co. of Canada, Ltd:: (1) The Sullivan concentrator, Chapman, B. C. (near Kimberley, B. C.), (2) the St. Eugene concentrator, Moyie, B. C., and (3) the Tadanac (customs) concen-trator, Trail, B. C. Differential flotation is the only concentration method employed in all three plants. Tables are used for pilot work only. Flotation equip-ment and control are similar in the three mills, and the flow sheets at the St. Eugene and Tadanac mills, while much simpler, are modeled after that of the Sul-livan concentrator. Successful differential flotation of Sullivan ore com-menced in the spring of 1920, in the pilot concentrator at Trail. During 1920, 193,804 tons were treated by this process. This operation continued without interrup-tion and with steady growth. For the first 7 months of . 1923, which concluded the pilot plant operation, ap-proximately 1100 tons were treated daily. I believe the Sunnyside plant of the United States Smelting &. Refining Co. was the only successful and large scale operation practising differential flotation prior to 1920. in North America. The Sullivan ore, because of its high iron content, was quite a different problem from that at Sunnyside. The entire tonnage of Sullivan ore had to be separated into three sulfide concentrate products-lead concentrate, zinc concentrate and iron concentrate. The choice and arrangement of equipment, and the original flow sheet for the Sullivan concentrator were controlled by the results of the exhaustive pilot mill test. These covered a continuous period of 3 1/2 years and involved the treatment of 1,076,368 tons of Sullivan ore. Satisfactory recoveries are made from feed; 11.0 per cent lead and 7.5 per cent zinc in the form of lead concentrate containing 69 per cent lead, 4.5 per cent zinc, and zinc concentrate containing 3.0 per cent lead and 49 per cent zinc. (The pure zinc mineral in Sulli-van ore is marmatite, 'containing approximately 54.5 per cent zinc and 10 per cent iron. It is apparent, there-fore, that 49 percent concentrate is high grade for this particular ore.)

Jan 8, 1927

By E. R. Macgregor, J. Halpern

The kinetics of the reduction of cupric salts in aqueous solution by molecular hydrogen to metallic copper are described. The rate of reduction appears to be homogeneously determined and shows a marked inverse dependence on the hydrogen-ion concentration. Precipitation of copper is more rapid and complete in sulfate than in per-chlorate solution. A mechanism is proposed which accounts for this behavior. IN recent years a number of important hydro-metallurgical processes have been developed in which metallic salts in aqueous solution are reduced by gaseous hydrogen, usually at elevated temperatures and pressures, and thereby precipitated either in metallic form (e.g. Ni, Co, Cu) or as an oxide or salt of lower valence (e.g. VO, and VA).1 ; In connection with applications such as these, most of which involve heterogeneously catalyzed reactions, recent demonstrations"-" that salts of certain metals, e.g., Cu", Ag' , Hg" , and Hg,+ can activate molecular hydrogen homogeneously and thus catalyze hydrogenation reactions in aqueous solution, are of considerable interest. For example, cupric salts catalyze the otherwise slow homogeneous reduction of dichromate and ceric salts by hydrogen, i.e. Cr,O; + 3HL. + 8H1 ? 2Cr'- -- 7H,O [1] 2Ce ' ! H.. ? 2Ce" | 2H . [2] In perchloric-acid solution, where Cu" is not appreciably complexed, the kinetics have been found" " to be of the form -d [H,] _- k,[HJ [CU"]' dt -LCu+' l+ (k ,/k,) [H] [3] where, K = 1x10"' exp [—26,600/RT] 1, mole-' min-' ... [4] and (k ,/k,) - 0.25 at 110°C. This kinetic behavior suggests that the reaction proceeds by a mechanism involving the following sequence of steps kt Cu" +H1CuH' 4-HA [51 k., CUH + CU" ? + 2Cu f H' [GI 6Cu'+ Cr,07 + 14H'+ 2Cr- (¦ 7H,O + 6Cu" ['i] fast The catalytic activities of the undissociated cupric-sulphate and cupric-acetate complexes are somewhat greater (by factors of 6.5 and 120, respectively) than that of the simple hydrated Cu" ion.'" These considerations suggest that, in contrast to the other hydrometallurgical hydrogenation reactions, referred to previously, reduction of cupric salts in aqueous solutions by molecular hydrogen, should proceed homogeneously, and in the absence of an extraneous catalyst. This has already been demonstrated" for acetate-buffered solutions where the product of the reaction is a precipitate of cuprous oxide (Cu,O). In the present paper, an investigation of the reduction of cupric salts in perchloric-acid and sulphuric-acid solutions, leading to the precipitation of metallic copper, is described. Some results for the sulphate system, which is of considerable hydrometallurgical interest, have been reported previously by Ipatieff",' " and by Schaufel-berger' but these do not give a quantitative account, of the kinetics and mechanism of the reaction. Experimental The reduction experiments were conducted in the 1-gal, titanium-lined autoclave described in connection with earlier related investigations," " and using a similar procedure. The solutions were made up by dissolving known amounts of CP grade Cu(ClO,), and HC10, (or CuSO, and HISO,) in dis-tilled water. While in the autoclave, the solution was stirred and maintained at a constant temperature (±loc) and under a constant partial pressure of hydrogen gas. It was ascertained that the agitation (provided by two 3-in., four-bladed stirrers, rotating at 900 rpm) was adequate so that at no time was the rate of reaction limited by solution of hydrogen. During each experiment, samples of the solution were withdrawn periodically, allowed to cool, and the concentration of copper remaining in solution was then determined electrolytically. Some Cu' is formed during the reaction, but undergoes disproportionation when the solution is cooled to room temperature. For purposes of kinetic calcula-

Jan 1, 1959

By John V. Beall

When a mine has ore averaging 5% lead, 7% zinc, 0.60% copper, 1/4 oz gold, and 6 oz of silver, adequate reserves, power and water, easy access to market, and is situated in beautiful natural surroundings with the advantages of a big city within a few hours drive, there is little left to be desired. Such a mine is the Mayflower mine of the New Park Mining Co. situated 30 miles from Salt Lake City in the Wasatch Mountains near Keetley, Utah.

Jan 1, 1949

By S. A. Mahon

AN interesting feature among the mining structures, on the Mesabi. iron range is the iron ore stacker erected in 1934 at the Mesabi Chief washing plant at Keewatin, Minn. It is built of structural steel, and carries a system of belt conveyors which collects the washed product of the plant and places it on a stockpile for subsequent shipment. Although the only one of its kind in the Lake Superior iron district, installations of similar nature have been used elsewhere in the handling of coal and gravel and in earthwork construction. The reasons for stocking Lake Superior iron ores may be as various and diversified as the methods used in building the piles. At the under¬ground mines the existence of the huge piles in evidence at each active shaft is due, principally, to climatic conditions in this north country where the shipping period is much shorter than the operating season. Conversely, at the washing. plants it may be desirable to stockpile washed ores because the shipping season is commonly of longer duration than the period during which the plants may be operated. Washed ores, and mixtures of which washed ores are a component part, have found high favor with the oper

Jan 1, 1935

By HUGH E. McKinstry

OPENING the sessions of the Mining Geology Committee, the program on postwar mineral controls drew a larger attendance than any other session of the entire meeting. In view of its general interest, the papers of this session, or a substantial portion of them, are printed elsewhere in this issue. Whether control of mineral resources can help to promote peace, how controls could be applied and to whom, are questions so far-reaching that naturally no pat answer was agreed upon. In fact the discussion took on something of the flavor of a debate between those who favor strict control and those who felt that attempting to ration nations in peacetime would defeat its own ends. Discussion from the floor emphasized the difficulties in administering any international control and the $64 question, that no one cared to answer, asked by a courageous young lady who was induced to mount the rostrum for the purpose, was whether the United Nations should exchange mineral controllers to police each other.

Jan 1, 1944

By Clinton H. Crane

IN October, 1925, J. R. Finlay delivered an address entitled, "The Future Price of Lead." Lead was then selling at 8.85c. and Mr. Finlay and most of the rest of us were concerned about the shortage. Now, a little more than six years after, lead is selling for 3.55c., and nobody is worrying about the difficulty of getting plenty of it. For 1931 the U. S. G. S. reports United States produc¬tion as 390,000 tons of recoverable lead in ore. Our estimate is slightly higher than this; nearer 400,000 tons. This is the smallest production since 1911 and 1912, but in spite of this, stocks for the year-have increased nearly 50,000 tons. Our estimate for the production outside the United States is 1,120,000 tons, or more than double the production of either 1920 or 1921, and 30 per cent more than in 1913. Stocks abroad probably have not increased more than stocks in the United States. In other words, foreign consumption is double what it was in 1.920-21, whereas domestic consumption is substantially less. It looks as if Mr. Krueger, president of the Swedish match trust, was right when he said that "This country had better stop worrying about Europe and think a little bit more about its own affairs."

Jan 1, 1932