Search Documents

By Clarence Merritt

STAINLESS iron, as mild stainless steel is usually called, an alloy ranging from 11.50 to 15.00 per cent chromium with carbon under 0.12 per cent, has been considered to be not appreciably affected in respect to corrosion resistance by heat treatment. This metal, while one of the most widely used of the "straight" chromium stainless alloys, has failed in many applications because of insufficient information regarding heat treatment. These failures have been attributed to many possible causes from an inherent lack of resistance to corrosion and misapplication to mysterious electrolytic effects or comparatively minute non-metallic inclusions. Many uses for a steel with such excellent physical properties is are latent in this alloy have been lost on account of corrosion failures which could have been avoided by applying proper heat treatment. The alloy has not received the recognition or attention it should because of the fact that' the details of its metallurgical behavior were not thoroughly understood. Response to heat treatment of the steel is well known as regards tensile properties, 1,2 but its application has been for improvement in tensile characteristics or on account of machining considerations rather than for corrosion prevention. The potential user of this steel has not been clearly advised in papers, either technical or commercial, that have been written about it in the last 10 years or more, of particular features that are of prime importance in developing the excellent properties of this metal. The data to be presented in this paper are concerned mainly with the effect of heat treatment on the corrosion resistance, but a study has also been made of the concurrent microstructural changes and an explanation developed for the phenomena revealed, as well as a correlation to the other physical properties-hardness, tensile characteristics and impact strength. Stainless steel, largely used for cutlery purposes, an alloy of approximately 13.00 per cent Cr with 0.30 per cent C, must be hardened and the surface prepared by polishing or pickling for best resistance to staining and corrosion.3 Monypenny reports that a loss of hardness is

Jan 1, 1932

By J. J. Jakosky

ALL electrical geophysical methods depend for their operation upon the effects produced by the flow of an electric current. By studying these effects it is possible to predict the general axis of current flow. The greater flow of current is in the path of greatest, effective conductivity; and since the effective conductivity of a mineralized zone is different from that of its surrounding envelope (usually much greater), it is possible to locate such a mineralized zone by the distribution of current. Due consideration must be given, of course, to geological structure, to type of mineralization, and to other factors. A number of methods are used to cause this flow of current, and various methods are available for detecting the presence of such current flow and for studying its effects. In a rather detailed way, this paper will discuss the theoretical and practical phases of the inductive methods of geophysical prospecting. ELECTROMAGNETIC GENERATION OF AN ELECTROMOTIVE FORCE The inductive method is so named because the current flowing in the conductor is obtained by electromagnetic induction, instead of by the use of ground electrodes through which a current is passed as in the applied potential systems, or by direct contact with the orebody. An alternating current flowing in a coil will create an electromagnetic field around the coil. This field will have the same frequency as the current and will radiate or travel outward from the coil in closed magnetic or flux circuits: These flux circuits (in air or a homogeneous medium) will be perpendicular to the plane of the coil and will extend or travel outward with uniform velocity in every direction. Maximum field exists in the plane of the coil. Such a coil used for transmitting or as the "energizer" will exhibit similar figure-eight characteristics to those exhibited by the direction-finding coil which will be described in detail later.

Jan 1, 1928

By Ivor Jenkins

Processes employing 'controlled at-mospheres in the heat-treatment of metals and alloys are now well established on an industrial scale, and the general principles involved and the advantages to be gained in the use of the technique have received considerable publicity over a period of years. During this time the greatest emphasis has been on the establishment of the process in industry, the main effort being devoted to development work on various types of atmospheres, their useful fields of application and the design of suitable heat-treatment furnaces in which they are to be used. The various types of controlled atmospheres are fairly well standardized, but there still remains a considerable field for the investigation of related problems, in connection with both the gas-generating equipment and the surface chemistry of the heat-treatment of metals, especially in complex controlled atmospheres. This paper describes certain investigations of this nature that were carried out in England up to 1939. The development of processes employing controlled atmospheres has been asso-ciated to a very large extent with the heat-treatment of steels, both because of the major importance of steel in industry and the many diverse and dificult prob-lems of surface chemistry involved when steels of such a wide range of composition are heated in the presence of active gases. Controlled atmospheres such as disso-ciated and burnt ammonia or charcoal gas are used in the heat-treatment of low-carbon and high-carbon steels, but from certain points of view a suitable atmosphere generated by the partial combustion of city gas is to be preferred. Both the ammonia derivatives are comparatively expensive, and even if the burnt ammonia is regenerated, thereby reducing operating costs, the capital expenditure of the gas plant may make it prohibitive for the smaller type of furnace installation. Charcoal-gas generators are not without their operating difficulties especially those associated with the quality of the charcoal, clinker formation and the removal of carbon dust from the generated gas. City gas has the advantage of being comparatively cheap and "on tap" in most if not all industrial centers. The use of raw city gas as a protective atmosphere in the heat-treatment of steels has been described,' but it presents certain difficulties because of its complex composition and its explosive nature when mixed with air. These factors, together with the tendency toward sooting at elevated temperatures, arising mainly from the hydrocarbon gases present, all militate against its use as a protective atmosphere in industrial furnaces. The following analysis, based on the analyses of city gas in different localities in Great Britain, indicates the wide limits existing

Jan 1, 1948

By Ivor Jenkins

Processes employing 'controlled at-mospheres in the heat-treatment of metals and alloys are now well established on an industrial scale, and the general principles involved and the advantages to be gained in the use of the technique have received considerable publicity over a period of years. During this time the greatest emphasis has been on the establishment of the process in industry, the main effort being devoted to development work on various types of atmospheres, their useful fields of application and the design of suitable heat-treatment furnaces in which they are to be used. The various types of controlled atmospheres are fairly well standardized, but there still remains a considerable field for the investigation of related problems, in connection with both the gas-generating equipment and the surface chemistry of the heat-treatment of metals, especially in complex controlled atmospheres. This paper describes certain investigations of this nature that were carried out in England up to 1939. The development of processes employing controlled atmospheres has been asso-ciated to a very large extent with the heat-treatment of steels, both because of the major importance of steel in industry and the many diverse and dificult prob-lems of surface chemistry involved when steels of such a wide range of composition are heated in the presence of active gases. Controlled atmospheres such as disso-ciated and burnt ammonia or charcoal gas are used in the heat-treatment of low-carbon and high-carbon steels, but from certain points of view a suitable atmosphere generated by the partial combustion of city gas is to be preferred. Both the ammonia derivatives are comparatively expensive, and even if the burnt ammonia is regenerated, thereby reducing operating costs, the capital expenditure of the gas plant may make it prohibitive for the smaller type of furnace installation. Charcoal-gas generators are not without their operating difficulties especially those associated with the quality of the charcoal, clinker formation and the removal of carbon dust from the generated gas. City gas has the advantage of being comparatively cheap and "on tap" in most if not all industrial centers. The use of raw city gas as a protective atmosphere in the heat-treatment of steels has been described,' but it presents certain difficulties because of its complex composition and its explosive nature when mixed with air. These factors, together with the tendency toward sooting at elevated temperatures, arising mainly from the hydrocarbon gases present, all militate against its use as a protective atmosphere in industrial furnaces. The following analysis, based on the analyses of city gas in different localities in Great Britain, indicates the wide limits existing

Jan 1, 1948

By Prof John E. Church

ONE of the most striking phenomena connected with the mines on the Comstock lode is the extreme heat encountered in the lower levels. This heat is not due to the burning of candles, heat of the men, and decomposition of timbers, all intensified by bad ventilation, as was the case nearer the surface. It proceeds from the rock, which maintains constantly a temperature very much higher than the average of the atmosphere in Nevada. The heat of these mines is a matter of more than usual interest, for they are the only hot ones now worked in the United States, and both in the present temperature encountered and in the increase which is to be expected as greater depths are reached, they appear to surpass any foreign mines of which we have a record. Hot mines are known also in other countries, as in the tin and copper lodes of Wales, where one of the veins worked by the United Mines is known as the hot lode. It has springs which discharge water at a temperature of 116' Fahrenheit, the depth being 220 fathoms, or 1320 feet. The heat of the air in these workings is. given at 100' to 113' Fahrenheit. The air is bad, and the heat in the drifts seems to be traceable to defective ventilation rather than to the real necessities of the case. Air is supplied through a small pipe, and is drawn from a place where the temperature is 95' Fahrenheit. Under such circumstances it is not surprising to read that in this hot mine the air is hotter than the rock, a state of things which I hare never observed in the Comstock. Other mines have been reported to the British Coal Committee as having temperatures of 106" Fahrenheit and thereabouts, but the only positive comparisons that are available at this writing are the following, all from Cornish mines : Mine. Depth Temperature. in feet. Air. Rock. Tresaveau,.....1581 86° 83° to 85° Consolidated Mines,. .. 1500 87° 86° " " . 1722 94o 93° " L .. .. 1764 94o to 96° 921/2° to 931/2°

Jan 1, 1879

By Pol Duwez, H. E. Martens

The high temperatures encountered in the operation of jet engines have imposed most drastic requirements upon the materials used in their construction. There are two different approaches to the materials problem connected with the design of parts in contact with high temperature gases. The first approach is to use a material which will perform satisfactorily at a temperature comparable to that of the gas. The second approach is to use a cooling system so that the material is maintained at a temperature appreciably lower than that of the gas. Besides the conventional method of cooling by means of a liquid in contact with the material exposed to a high rate of heat transfer, a less orthodox method consists of making the part to bc cooled of a porous material', so that the cooling fluid can be forced through the pores, In this scheme, the temperature of the coolant moving in a direction opposite to that of the heat flow increases gradually while passing through the porous material, and the coolant forms a protective layer on the surface exposed to heat, This method, referred to as ((sweat cooling," was pro- posed at the Jet Propulsion Laboratory in September 1944, and the experimental work on the preparation of porous metals was started early in 1945. The sweat cooling method opens new lines of research in powder metallurgy by extending the field of application of porous metals. The porous metals available at the present time are used mostly as bearings or filters, and a rather limited number of alloys are made for these applications. In addition, the fabrication of bearings or filters does not require a very close control of the permeability, while in the case of sweat cooling such a control is of primary importance. In designing a sweat cooled part it is imperative to assure a given rate of flow of coolant under certain conditions of Pressure drop. Generally, the Proper pressure drop and the rate of flow of coolant are deduced from heat transfer and design considerations, and consequelltl~ the Permeability of the Porous metal to be used is also determined. It is therefore necessary for the designer to have available a continuous series of porous metals covering a range of permeability as wide as possible. Contrary to the requirements established in the fabrication of filters, the actual pore size of a porous metal intended for sweat cooling is of little consequence, except for its effect on permeability. The tensile strength is likely to be of great importance for some applications. Since the tensile strength of a porous alloy decreases with increasing porosity, an important problem is to develop porous alloys having the maximum permeability with minimum porosity.

Jan 1, 1949

By James Aston

A proper consideration of this subject is not confined to the technical channels of production and metallurgy. It concerns an industry, and should cover economic aspects which are of material importance in any program of development. The discussion may logically be treated under three subdivisions, as follows: (1) manufacture, (2) characteristics related to quality of material; (3) adaptability and exploitation of product. Manufacture of Wrought Iron The manufacture of wrought iron is the most ancient art of the ferrous metal industry. The eighty years or less of existence of processes identified with our modern "Age of Steel" is a relatively brief interval compared with the several thousand years associated with the production of wrought iron by man. From the primitive early methods of production, manufacture for many centuries followed the line of direct reduction. There were developments as experience was gained through the years; but man's needs for a strong, ductile, forgeable product were met by reducing the ore to metallic iron in a single-stage operation. Following the development several centuries ago of what has become our modern blast-furnace operation, manufacture of wrought iron was gradually transformed into a two-stage method of first producing cast iron and then refining this to the desired degree of forgeability; the forerunner in principle of today's scheme of manufacture of steel. The product retained the essential characteristics of highly refined base metal with iron-silicate slag incorporation, which were associated with the material resulting from direct reduction methods. Cort's invention of the puddling process in 1784 is a landmark in wrought-iron manufacture. It consisted essentially in adapting a coal-fired reverberatory furnace to the refining operation; thus lifting the industry out of the slough of

Jan 1, 1935

By E. W. Davis

IF the tonnage of merchantable iron ore remaining in the Lake Superior district is divided by the average of the annual shipments for the past 20 years, it will be found that this ore supply will be exhausted in approximately 35 years. This computed exhaustion period would be an indication of the future activities of the iron-mining industry if it were not for the fact that merchantable ore is being manufactured from low-grade ore, of which there is an almost inexhaustible supply in the Lake Superior district. It is true that at present only the simplest of these low-grade ores are being concentrated to any considerable extent, but progress is being made with the treatment of the more complex ores, and now, in addition to 20 washing plants on the Mesabi Range, three plants are equipped with jigs for the treatment of ore that cannot be concentrated simply by washing. The latest addition to the ore-treating plants of the Mesabi Range is a magnetic roasting and concentration plant at Cooley, Minn., in which ore that cannot be concentrated either by washing or by jigging is roasted to the magnetic state and concentrated on magnetic separators. This plant is beginning its third season of operation, and while it is too soon to make definite predictions, there are strong indica-tions that this new process may make commercially possible the manu-facture of high-grade, merchantable iron ore from large quantities of low-grade ore now considered worthless. After the iron oxide contained in an ore has been converted to mag-netite, almost any desired grade of concentrate can be produced, using magnetic-concentration equipment of the types now in general use for the concentration of the natural magnetites of New York, New Jersey and Pennsylvania. The conversion of hematite (Fe2O3) to magnetite (Fe3O4) is easily accomplished by heating the ore to a dull red tempera-ture in a reducing atmosphere. The reaction is slightly endothermic, and while it requires 200 B.t.u. to heat to 900° F. one pound of hematite ore containing 45 per cent Fe, it requires only 100 B.t.u. to convert the oxide into magnetite. In the laboratory, using small quantities of ore, this conversion is very simple, but large furnaces suitable for commercial

Jan 1, 1936

By Matsubara, A.

THE problem of the equilibrium between iron, carbon, and oxygen was first carefully investigated by E. Baur and A. Glaessner,1 who determined the equilibrium conditions of the two reactions Fe304 + CO ? 3FeO + C02 (1) FeO + CO ? Fe + C02 (2) within the range of temperature of 350 to 900° C. The next series of investigations was made by R. Schenck and his co-workers,2 who sought to check the results of Baur and Glaessner's work within the range of 550° to 700° C. and to elucidate the conditions of formation of iron carbide. The equilibrium conditions at the higher temperatures, however, are generally understood to be much more complicated, owing chiefly to the formation of solid solutions between iron, its oxides, and carbide; nevertheless their determination is of much more practical importance than those at the lower temperatures. It is well known that each of the reactions is reversible; equilibrium is established when the partial pressure of oxygen in the gaseous phase has become equal to the dissociation pressure of magnetic oxide in equation 1 and that of ferrous oxide in equation 2. These equilibria are subsequently designated by "the Fe304-FeO equilibrium" and "the FeO-Fe equilibrium," respectively. As the Fe304-FeO equilibrium has three phases with three components, it must be bivariant. But the reaction involves no pressure change in the gaseous phase, hence the final composition of the latter is practically unaffected by pressure. To know, the equilibrium conditions, the compositions of the gaseous phase at different temperatures must be determined. At the higher temperature, however, iron and its oxides dissolve one another in various proportions forming solid solutions; in many cases the content of oxygen in the solid phase becomes a new independent variable.

Jan 2, 1921

By Oliver Bowles

DIMENSION stone is a convenient term applied to stone sold in blocks or slabs of specified shapes and usually of specified sizes, as contrasted with crushed, broken and pulverized stone, discussed in another chapter. Dimension stone includes cut stone, rough building stone, ashlar, rubble, paving blocks, curbing and flagging. Riprap-large, irregular blocks used for shore protection-is classed more properly with crushed and broken stone. COMPOSITION, VARIETIES AND PROPERTIES Stones used as blocks or slabs are of many kinds. The principal varieties are granite, sandstone, limestone and marble. Slate is covered in another chapter. Granite is a visibly granular crystalline rock consisting essentially of feldspar, quartz, and mica or hornblende. Limestone consists essentially of calcium carbonate, with which may be associated certain impurities such as clay, sand, or iron oxide. Dolomites and magnesium limestones used as dimension stone are classed with the high- calcium limestones, as they are used in the same way. Marble is a crystalline form of limestone. Sandstone consists essentially of silica in the form of sand grains cemented together into a coherent mass. Although rock occurrences are numerous and widespread, the ex- acting requirements of use condemn all but a small fraction of them for commercial use as dimension stone. No deposit that has closely spaced cracks, lines of weakness, or joints can be so used because sound blocks of moderate to large size are demanded. Uniform texture and grain size, constant and attractive color, and freedom from impurities that may cause stains or deterioration usually are required also. Hardness is a variable property. Granites are as hard as or harder than steel while limestones and marbles may be scratched easily with a knife. The hardness of a sandstone depends upon the degree of cementation of the grains. Workability depends to a considerable extent on hardness, but the degree of hardness has little influence on use except when stones are subjected to severe abrasion, as on steps or floors. "Texture" as applied to stone relates to the arrangement, uniformity, and size of the constituent grains.

Jan 1, 1949

By A. Faison Dixon

In India the production of mica, which in other countries is of very minor importance, is one of the staple, long established industries, and ranks high in the statistics of mineral products. Nearly two-thirds of the mica of commerce comes from India. The Indians have used mica for glazing and decorative purposes through many centuries. About 14,000 men are employed in and about the mines, and the indigenous and primitive mode of mining is still followed; but, by reason of the exhaustion of the surface supply hitherto won without intelligence or capital, it will not be many years before the present interesting and casual methods will be replaced by a less archaic and more profitable system. India on the whole has little mineral wealth, but the unique resources of its mica-fields, cheap labor, and favorable natural conditions render it unlikely that any other country can ever more than temporarily contest her leadership in the production of this one minor but essential mineral. Mica plays a small but indispensable rôle in a variety of fields of dissimilar application. Its use and value depend upon characteristics which different kinds of mica have in varying degrees, each kind being adapted to its own special purpose. Its well-known characteristics of transparency, flexibility, elasticity, toughness, high dialectric strength, perfect flatness, ease of splitting into thin films, ability to stand high heat and sudden changes in temperature, give it value in many industries. No other substance, natural or artificial, has the same combination of qualities. The oldest use of mica is in glazing. By reason of the improvements in annealing glass, this is not now of great importance, but mica is still employed for the covers of ikon images in Russian churches, the windows of anthracite stoves, compass

Jan 1, 1914

By F. V. Lenel, G. S. Ansell

The creep behavior of an aluminum -aluminum oxide alloy, A T 400, fabricated by compacting an atomized aluminum powder, extruding the compact, cold working, and recrystallizing the extrusion, was investigated. This alloy has a dispersion spacing of 1 . Previously Ansell and Weertman determined the steady-state creep rate of a recrystallized aluminum-aluminum oxide SAP-type alloy, MD 2100, with a 0.48-p dispersion. This alloy was found to have a steady-state creep rate of less than 10-6 min-1, too small to be measured accurately. By employing a more sensitive method of measuring creep rate, it was possible to determine the steady-state creep rate of AT 400 alloy, which is somewhat faster than that of MD 2100, at a series of temperature and applied stresses. Above a stress of Burger's vector, A = dispersion spacing, u = is a shear modulus) the rate follms an equation of the type: Steady-state creep rate K = A exp. where A is a constant, Q is the activation energy for sey-diffusion, and is the applied stress. At stresses lower than the steady-state creep rate drops off sharply and is no longer in agreement with this equation. This behavior is in good agreement with that predicted by the model for dispersion strengthened alloys in the stress and temperature range investigated. The absolute value of the creep rate is, however, four orders of magnitude lower than that predicted if the normal number of active dislocation sources are assumed to be present. It is concluded that in this SAP-type alloy the usual three-dimensional dislocation network is not present. Instead, short dislocation segments extending from one dispersed particle and terminating at a neighboring particle may act as dislocation sources. With this provision the creep model proposed by Ansell and Weertman reasonably accounts for the creep behavior which was observed. RECENTLY, Ansell and Weertman1 proposed a dislocation model from which they derived creep equations to describe the steady-state creep behavior of dispersion - strengthened alloys. Following Schoeck,2 they assumed that the rate controlling process for steady-state creep is the climb of dislocations over the dispersed particles. In order to verify their creep model, Ansell and Weertman determined the steady-state creep behavior of an aluminum-aluminum oxide SAP-type alloy, MD-2100, in both the fine-grained as-extruded, and coarse-grained recrystallized conditions. Since the grain size was the order of the dispersion-spacing, their model was not applicable for the as-ex- truded alloy. It should, however, be applicable to the coarse-grained recrystallized alloy. The results they obtained were rather unexpected. No meas-ureable steady-state creep was observed for the recrystallized MD-2100 alloy. If their model is correct, and if the second-phase particles act solely to hinder dislocation motion, then some measureable steady-state creep would have been expected. On this basis, they postulated that, in this SAP-type alloy, the main effect of the fine dispersion was to inactivate dislocation sources rather than to hinder the movement of dislocations. In order to understand more fully this unusual creep behavior, and to determine the validity of the model proposed,' the steady-state creep behavior of an aluminum-aluminum oxide recrystallized SAP-type alloy, with a somewhat coarser dispersion spacing, was investigated. The results of this study are presented in this paper.

Jan 1, 1962

By C. B. Post, G. V. Luerssen

It is generally recognized that non-metallic inclusions in steel come from two principal sources. First are the chemical reactions in the furnace, or in subsequent deoxidation, resulting in slag which does not free itself from the metal. Much information has been published concerning these chemical reactions and their control through proper attention to slag viscosity, composition of deoxidizers, and other qualities. The studies of this subject by C. H. Herty, Jr. and others through the medium of physical chemistry have yielded much information for the steelmaker. The second source is erosion of ladle refractories, such as lining brick, stoppers, nozzles and runners, causing entrapped particles of globules of fluxed silicate material. In contrast with the large amount of information available on the first source, relatively little has been published on the subject of erosion which, in the case of basic electric melted steel, is the principal source of nonmetallics. This is probably due to the fact that the problem was assumed to be one of simple mechanical erosion, which could be solved primarily by modification of ladle practices. Good improvements have been made by elimination of slurries in the ladle, better ladle and runner refractories, and more attention to pouring temperatures. It is doubtful, however, that this problem has been recognized in its true light since it is not one of simple mechanical erosion but rather one of chemical reaction between the metal and the refractories; and in this sense is as much a problem of physical chemistry as the reactions involved in the actual steelmaking process. The influence of ladle refractories on the resulting cleanness of steels was early recognized by A. McCancel who examined large inclusions in steels made by both acid and basic practices. His chemical analyses showed the large influence exerted by the manganese content of the steel on erosion of the ladle and nozzles used in those days. The presence of MnO in such inclusions led McCance to the hypothesis that both basic and acid steels react chemically with the ladle refractories so that small globules of fluxed refractories are carried in the stream into the molds. This early work of McCance was checked by one of the present authors on basic electric bearing-steel, and it was found that on steels containing as low as 0.40 pct manganese the fluxed surface of the ladle lining after delivering such a heat showed as high as 25 pct MnO by actual analysis. Furthermore, by lowering the manganese content of the steel to 0.20 pct, ladle erosion was decreased with a corresponding decrease in silicate inclusions in the steel. Limitations placed on the manganese content for the required inherent properties made it impossible to pursue this line further, and subsequent attention was concentrated on improved ladle refractories, care in keeping the ladle clean and free from loose refractories up to the time of tapping, and pouring the steel at optimum temperature. Our study of the chemical reactions at the metal-brick interface between steel and ladle refractories was revived in 1939 as a result of an experimental observation made on the cleanness of alloy steels of the SAE types. This observation showed that the relative cleanness of such steels made in basic electric arc furnaces of 12 ton capacity and poured in ingots ranging from 1100 to 2200 lb weight was determined to a large extent by the ratio of the manganese and silicon contents, provided other steelmaking variables such as tapping temperature, pouring temperature, pouring time, amount of aluminum added for grain size control, and degree of deoxidation in the furnace were kept reasonably constant. Detailed studies made on the deoxidation and slag practice during the refining period of basic electric furnace practice showed that these two variables exerted some influence on the resulting cleanness of steel in the form of bars and forgings. The important variable, the manganese-silicon balance, was not apparent until heats were made in succession by the best furnace practice kept under fairly rigid metallurgical control. Another observation pertinent to this work concerned the similarity in the microscope of slag particles causing magnaflux or step-down indications in subsequent rolled bars, and the patches of slag frequently seen on the surface of ingots. These patches are generally believed to come from the glassy metal-brick interface in the ladle and represent an entrapment of such glass (both from the ladle brick and nozzle) in the metal as it flows over the refractories in the neighborhood of the nozzle. These glassy particles are carried down into the mold with the liquid steel, and gradually coalesce into a slag "button" which floats on the surface of the steel as it rises in the molds. Periodically the button is washed to the side of the ingot where it is trapped between the surface of the ingot and the mold, later appearing as a slag patch on the surface of the ingot after stripping. Even though most of the small glassy particles coalesce into a slag button while the ingot is being poured, it is logical to suspect this step in the steelmaking process as being a source of slag lines large enough to cause trouble

Jan 1, 1950

By C. P. Fiske

THE pottery of the New Jersey Zinc Co. (of Pa.) is equipped to make three classes of refractories; namely, spelter vessels, spelter condensers; and high-grade fire-brick. The most important of these are the spelter vessels, on account of the extreme severity of the service which they must perform, necessitating great care in the selection of materials and in the whole process of manufacture. Next to the spelter vessels in importance? come the condensers, as large numbers are used in the manufacture of spelter, and improvements m quality result in material decreases in working cost. , While the fire-brick which form the laboratory, or high-temperature portion of the spelter furnaces, are placed at the foot of the list, they-are nevertheless of much importance, since high quality will decrease the frequency of the always expensive shutdowns for repairs. To promote simplicity, the manufacture of these three products will be described separately in this paper, except in so far as materials and the crushing and handling system common to all are concerned. Materials Bond Clay.-The bond clay used entirely at the Palmerton pottery is a St. Louis clay furnished by the Grand View Fire Clay Co. It is stored in a system of covered bins, and no attempt is made to weather -it in the, accepted sense of the term " weathering." Some years ago our clay was weathered before pugging, but we did not find the benefit sufficient to offset the additional handling and the loss. of clay incurred. Furthermore, we believe that the rotting of the pugged mix (described later), accomplishes the same results to better advantage. That there is some action taking place in the clay while stored in the covered bins, however, is, evidenced by an increase in volume which at times has caused damage to the retaining walls of the bins. We have at present a stock of bond clay weathering in the open, and when this is put into service an opportunity will be afforded for making comparisons-with the clay as usually handled.

Jan 10, 1917

By J. P. Timmons, J. H. Moran, G. K. Miller, M. A. Coufleau

A prototype equipment has been designed and built for the digital recording of well logs on magnetic tape at the same time that the regular film recording is made. The format of the digital tape produced is such that it can be used directly at the input of the ZBM 704, 7090 or other models of ZBM computers which accept digital magnetic tape. This apparatus has been used for the experimental field recording of dipmeter tape logs which were subsequently computed by means of an ZBM 704 or 7090. In this paper the equipment and the digital tape are described briefly, and their application to the computer-interpretation of dipmeter data is discussed. A principal element in the interpretation of the dipmeter log is the correlation of the three microresirtivity dipmeter curves to determine the depth displacements between them. Several correlation methods for computer use are considered, with particular attention to their sensitivity to error and their consumption of computer time. The tape data were used to compute information content of the dipmeter microresistivity curves in terms of their frequency spectra. The results show that the sampling rate used in recording the digital information is quite adequate and illustrate a use of the digital tape in evaluating the characteristics of new tools. Some examples of field results are shown. It can be foreseen that, when digital tape recording becomes available for general field use, a whole new realm of possibilities will be opened up for the processing of other well logs through computations, which hitherto were not feasible because they were too laborious and time-con.sunzing. INTRODUCTION The last few years have seen a revolution in the design and production of data-processing equipment. Stored-pro-gram digital computers have progressed from a research curiosity to the basis of a major industry. There are now hundreds of such machines in daily use in the United States. With the acceptance of a technique that was, in fact, already clearly described by John von Neumann in 1945, the last decade has seen great strides in the development'of components, reliability, programming systems and, most spectacularly, in the sheer number of machines built and in use. In 1957 there were enough digital computers available to the oil industry to justify the suggestion that it would be worthwhile to investigate the possibility of using these machines in processing well log data.' The first result of this investigation was the appearance of what may be referred to as the input-output bottleneck. Well logs are customarily recorded on film. To get these data into a machine required then (and still does): a time-consuming semi-automatic reading of the film; conversion of the log data to digital form; and recording these digital data in some medium acceptable for computer input, such as cards, magnetic tape, or punched paper tape. However, the recording, reading, and re-recording could only result in deterioration of the data. Therefore, it was concluded that the fist step should be the development of a new, more direct recording technique supplemental to the film recording, which would provide easy access to the digital computer. There are many solutions to the problem of recording log data in an easily recoverable form. After careful consideration it was decided to adopt the boldest solution which, it was felt, was also the most elegant. It was decided to record well logs directly, in the field, on magnetic tape in such a way that this tape could be used without further modification as an input to the IBM 704 or 7090 computer. To realize practical field recording of magnetic tape logs, it became necessary to develop in a rather small package, an analog-to-digital converter, a tape recorder, and the necessary multiplexing and control circuits to allow the simultaneous recording of a multiplicity of logging signals. The magnetic tape recording was to be made simultaneously with the conventional logging operation in such a way as not to interfere with it. Along with the development of hardware, it was necessary to begin development of interpretation techniques and machine programs that would exploit the power of the digital computer. Here, again, there is a long list of possible applications. After much consideration it was decided to concentrate on the interpretation of the dipmeter log as a first application. It is the object of this paper to describe in some detail the developments sketched in the last three paragraphs.

By D. D. Dunkin

Sandstone has been prepared for glassmaking purposes, and marketed from the White River Valley in Arkansas at Guion, Izard County, since about 1910—soon after the completion of the White River Branch of the Missouri Pacific R. R. Co. Until 1921, operations were somewhat spasmodic and ended in many failures. In that year a plant was built by the Silica Products Co., Inc., and since that time the operation has been continuous and steady. The land is held under leases, covering about 30 square miles of the best sandstone adjacent to the railroad. Most of the product is shipped to glassmakers. Geology The St. Peter sandstone is rather widely distributed in north central Arkansas and is exposed most prominently in outcrops along the slopes of the White River Valley and its tributarirs that form the division between the Boston Mountains to the south and the Salem Plateau of the Ozarks to the north. It is of Ordovician age and is generally underlaid by Cotter dolomite and capped by Plattin limestone, except in the vicinity of Bellefonte and Everton. At those places, it is a massive cross-bedded, laminated, saccharoidal sandstone; underlying it is the Everton limestone and overlying it, the Joachim magnesium limestone The sandstone at Everton contains numerous phosphatic pebbles and inclusions of sandy limestone. The irregularity of cross-section, the evidence of sorting action and the phosphatic pebbles appear to be indications of secondary deposition The St. Peter sandstone occurs as a massive formation in the picturesque bluffs along the White River Valley from near the eastern escarprnent of the uplift northwestmard into the Ozarks. The exposure shows a series of gentle anticlinal and synclinal folds. The greatest thickness is at the southeastern end, where it is over 100 ft. in many places. It thins out to the north and west and then to isolated and scattered deposits which cap the ridges and mountains of the Ozarks.

Jan 1, 1928

By A. T. Goldbeck

THE use of stone as a building material in relatively large blocks is recorded in ancient historical records but only within the past 200 years has broken stone in small sizes begun to have extensive use, principally in highway construction. Tresaguet, in 1764, describing his method for highway construction in France, required the top surface to be built of stone about the size of a walnut, broken by the use of a hammer. It is said that the Romans, in the top layer of their rather massive roads, used large stones bonded together with lime mortar and bedded in small stones mixed with mortar. Much of the early macadam as built by McAdam around 1815 in England was made with hand-sledged broken stone. In 1858, the use of crushed or broken stone received a great impetus from the invention in that year by Eli Whitney Blake of what is said to be the world's first stone crusher. As a consequence of that invention, stone could be crushed to small sizes with considerable ease and, as a natural result, the use of crushed stone in macadam roads and as railroad ballast increased at a great rate. Also, as portland cement came into use, machine-produced crushed stone furnished readily available aggregate. Rapidly, other uses developed, such as for fluxstone in the production of pig iron and for other metallurgical operations and chemical utilizations. These utilizations made for the rapid growth of the crushed-stone industry and this growth is still proceeding with the growth of population and the development of new uses, notably the employment of limestone for the improvement of soils for agricultural purposes. The industries of which the production of crushed stone is a part have a tonnage second only to that of mineral fuel in the mineral industries of this country.

Jan 1, 1949

By Joseph W. Roe

MANY questions arising in the work of the mining engineer may be solved quickly and with sufficient accuracy by the methods of descriptive geometry; but, unfortunately, this subject is more often considered from a mathematical view-point than as an effective tool. for solving practical problems. Some of the principles involved are merged into the ordinary operations of mechanical drawing, and are used unconsciously by the engineer in his every-day work. The rest are stowed away on the book-shelf with his forgotten or rarely-used college text-books. One reason for this condition of "innocuous desuetude " may lie in the unfortunate and often cumbersome notation which it has been found necessary to introduce. If some of these principles can be recalled to the engineer's attention in terms of every-day use they may prove of practical bearing. Recently, in talking with several mining engineers, I used some of the drawing-room methods of a machine-designer, to the evident surprise of those around me. These men were perfectly familiar with the methods, but their application to mining-work had not occurred to them. At their suggestion the present paper is offered, not in any way as a treatise, but merely to suggest a certain point of view, in hope that it may lead others far more familiar with mining-problems to pursue the subject further. I. To FIND THE STRIKE. As the simplest and most fundamental problem, let it be required to find the strike of a vein when the location and elevation of three points on the outcrop are known. It will be assumed for the present that the vein is a plane.

Mar 1, 1910

By B., Hoyaux

A first requirement for assessing the safety of a rock slope, either artificial or natural, particularly if the rock behaves in an elastic-brittle manner, is a proper knowledge of the distribution of stresses within the slope and their development with time and advancement of workings.

Jan 1, 1972

By H. G. Doll

A new electrical logging method. called MicroLaterology is described. whereby the resistivity R of the invaded zone close to the wall of the bore hole is measured. This method essentially utilizes a system of concentric circular electrodes iml,edded in an insulating support which is applied to the wall of the hole. A beam of current of very small diameter is focused horizontally into the formations by means of an automatic control device. and then opens widely at short distance from the wall. with this method, R most often can be recorded directly. except when the mud cake is very thick. in which case a correction is easily provided. The basic role of factor R in the quantitative analysis of electrical logs in terms of fluid saturation and of porosity is explained. The paper is illustrated with field examples. INTRODUCTION In electrical logging. the resistivity of that part of the penneable and porous formations which is invaded by mud filtrate is an important factor in the interpretation. Measurements made with the conventional devices — normal. lateral — and also with improved systems as the Laterolog and induction logging' — are very often more or less affected by the presence of the invaded zone. and the knowledge of the resistivity of this zone is useful in the evaluation of the true resistivity of the beds. which itself is a basic element for the determination of fluid saturation. Moreover. the comparison of the resistivity of the invaded zone with the resistivity of the mud filtrate gives valuable indications on the magnitude of the formation resistivity factor — which in turn is necessary for the quantitative interpretation of the logs. both in terms of fluid saturation and of porosity. On the other hand. it is generally admitted that the invaded zone is not a homogeneous medium separated from the uncon-tamirlated part of the bed hy a well defined cylindrical boundary. but that the fluid distribution—filtrate. connate water. hydrocarbon — and hence. the resistivity. in the invaded zone varies progressively with the distance from the wall of the hole. The term "resistivity of the invaded zone" therefore corre-sponds to an average value which is a function of the distribution of the fluids Inasmuch as the law of this distribution is not exactly known, the resistivity of the invaded zone is not a well defined factor. A much better definition is obtained if the medium under consideration is limited to that part of the formation which is within a short distance from the wall of the hole. It seems likely a within a distance of at least two or three in., most of the fluids in in the pores of tile formation have been displaced by the mud filtrate. The connate water has almost certainly been flushed out. and the oil. if any has generally been reduced to a comparatively small amount. The resistivity witliir~ the radial limit of two to three in. is. therefore. prac.tically constant at an). given level: its value. at least when the proportion of conductive solids in the formation is negligible. is chiefly dependent on the resistivity of the filtrate and on the porosity of the formation, and is affected only to a relatively small degree by the presence of the small amount of residual oil. This part of the formation close to the wall of the hole will he designated in the following as the "flushed zone." a-distinguished from the more general term of "invaded zone'. which relates to the part of the formation extending from the wall out to the distance where the formation is completely uncontaminated. The symbol R,, will he used for the resistivity of the flushed zone. (The notation R is related to the radial distance from the hole. If x designates this distance. xo is the initial value of x, i.e., the value corresponding to the region very close to the wall.) The determination of R is difficult, if not impossible. from logs made with the conventional devices. The long normal and the long lateral are. of course. not suited for this purpose because their radii of investigation are by far too large. The short normal. and the limestone sonde—-after correction for the effect of the hole hole — give resistivity values which corre. spond to materials situated within a comparatively short distance from the hole, but this distance is still several time. as great as the thickness of tire flushed zone. The only value which can be obtained with these devices corresponds to an average resistivity of the invaded zone- — and this only provided the invasion is deep enough, since otherwise the meas "red values would also be affected by the uncontaminated region beyond the invaded zone. It should nevertheless be recalled that despite these limitations. the measurements given by the short normal and or the limestone sonde are always very useful for qualitative interpretation. and also in favorable cases for the qantitative analysis of the logs in terms of saturation and porosity. The MicroLog. which was primarily developed for the detection of permeable beds and for an accurate determination of their boundaries. provides a good approach towards the evaluation of R. In the case of hard formation.. however. The

Jan 1, 1953