Search Documents

By Umberto Cassará de Castellammare Scott Siciliano

A proposta desta pesquisa foi desenvolver uma metodologia que empregasse radiação gamae a técnica de “Cross-Correlation” para medir a velocidade das pelotas de minério no duto. Uma unidade experimental foi projetada e construída para realizar simulações de fluxos de duas fases, usando um medidor de fluxo, instalado externamente ao tubo, consistindo em dois sistemas independentes, cada um composto por uma fonte 241Am de radiação gama (59,62 keV de energia) e um detector cintilador NaI (1 x 1 "). Estes sistemas estavam localizados no mesmo plano vertical e separados por uma distância de cerca de 18,0 cm. Como Pelotas, foram produzidos corpos de prova de composição distinta a fim de obter um espectro de densidades para verificar a validade da metodologia. Os resultados mostraram que o uso da densitometria gama associado com a medição do coeficiente de "Cross- Correlation” permitiu calcular o tempo transiente entre dois sinais e assim, calcular a velocidade da pelota.

Aug 16, 2017

By Eustáquio Vieira Júnior, Welder Gomes Gonçalves

Os altos-fornos podem apresentar ocorrências de arrombamento e/ou avermelhamentos dos algaravizes, e esses têm como conseqüências: alto risco na integridade dos conjuntos joelhos/algaravizes, resultando em baixa segurança operacional; elevação brusca da temperatura interna dos algaravizes, causando avermelhamentos e/ou arrombamentos recorrentes por desgaste acentuado do revestimento refratário; necessidade de paradas emergenciais; necessidade de troca dos conjuntos de algaravizes por desgaste acentuado do perfil refratário. Uma possível causa relacionada com essas ocorrências pode ser a combustão no interior do algaraviz do carvão que foi injetado pelas lanças, causando desgaste do revestimento refratário e conseqüentemente avermelhamento e/ou arrombamento do conjunto. Para evitar esse tipo de ocorrência foi instalado sistema de monitoramento de fenomenos na zona de combustão. Esse sistema trabalha como complemento do diferencial de pressão dos algaravizes e o anel de vento. Nesse trabalho, são mostradas as características do sistema de monitoramento e suas particularidades e os resultados alcançados após a implantação dos sistemas no que se refere aos danos em conjuntos de sopro.

Oct 1, 2019

By Francisco Alberto Marreiros da Rocha Filho

O uso de vanádio na produção de vergalhões microligados data do início do século XX, sendo amplamente utilizado na construção civil voltada para regiões susceptíveis a abalos sísmicos. Desse modo, este trabalho visa revisar os efeitos promovidos pelo uso do vanádio na fabricação de vergalhões antissísmicos, levando em conta a utilização de dois processos distintos de laminação – Forno de reaquecimento a Gás Natural (FGN) e Laminação Direta (LD) – como forma de conferir ganhos em resistência, mantendo-se níveis satisfatórios de tenacidade. Foram realizados ensaios microestruturais e de propriedades mecânicas entre lotes provenientes dos dois processos, avaliando-se propriedades como tamanho de grão médio, limite de escoamento e limite de resistência, correlacionando-as com o efeito provocado pelo uso do vanádio, concluindo-se que seu impacto no refino de grão austenítico/ferrítico e endurecimento via precipitação de carbonitretos de vanádio é de fundamental importância para a obtenção de propriedades mecânicas satisfatórias em vergalhões antissísmicos.

Oct 30, 2017

By José Fagundes Jr., Juliano Braz Possatti, Bruno Câmara Vieira, Gabriel Godinho Alves, Bruno Bastos da Silva Murad, Cristina Maria de Oliveira Roque

Driven by market trends, increasing environmental accountability, government regulations and fostered by the Company’s strategic plan, ArcelorMittal Tubarão has developed new steel products to deliver better solutions to fit each customer’s needs. This often translates in higher strength, more complex and dimensionally challenging (thinner and wider) steels to attend a broad array of goals, such as reduction of vehicles fuel consumption and carbon emissions, increase in fatigue performance of heat treated parts, higher load capacity per net weight in vessels or wagons and lower supplying lead time as ArcelorMittal Tubarão establishes itself as a domestic option for so far imported grades. Based on the annual Product Development Plan, a structured workflow involves technical discussions from an operational point of view about safety issues, metallurgical project, steel grade family definitions, offline simulations prior to field trials, deformation resistance and process parameters adjustments and scheduling strategy. As a result of the increasing synergy between the areas, the share of new materials developed in recent years has been sustainably increased up to 15% in 2018, adding value to the final product without impact on hot rolled coil output and with a low cobble index.

Oct 1, 2019

By Leandro de Arruda Santos, Lorena Isabela de Oliveira Ribeiro, Jéssica Dornelas Silva, Pedro Damas Resende, João Victor Lucas Amim, Suzanny Cristina Soares Martins, Vicente Tadeu Lopes Buono

O objetivo do presente estudo foi avaliar a resistência à fadiga de duas ligas de NiTi diferentes sob condições de teste controladas por deformação a 25°C por meio de testes de fadiga por flexão rotativa. Além disso, as propriedades mecânicas, térmicas e estruturais dos fios foram caracterizadas por ensaios de DSC, DRX, MEV/EDS e tração. Os resultados revelaram que ambos os materiais são superelásticos à temperatura ambiente e, portanto apresentaram composição basicamente austenítica de sua matriz. Os resultados de ensaio de tração são condizentes com a caracterização térmica e estrutural, pois os materiais apresentam recuperação total de forma após ciclos de carga e descarga em tração. Ambos os materiais são ricos em titânio, um deles apresenta camada de óxido superficial enquanto o outro apresenta acabamento superficial. Apesar das propriedades similares a amostra 1 apresentou média de 77 ciclos até a falha, enquanto a amostra 2 resistiu a 1827 ciclos..

Oct 25, 2019

By Rubson Mação Camporez

Estudos recentes indicam que o gasto devido à corrosão nos USA giram em torno de 276 bilhões de dólares por ano, isto significa 3,1% do PIB deste país, tendo a corrosão atmosférica uma importante parcela deste montante. Muitos estudos foram realizados a fim de determinar a agressividade da atmosfera e avaliar os efeitos da corrosão atmosférica nos metais usados para aplicações estruturais. Este artigo tem como objetivo comparar dois ambientes em termos de severidade da atmosfera, assim como sua influência na degradação do aço estrutural ASTM A-572 Grau 50. Toma-se como cenário a planta industrial da Medabil Sistemas Construtivos, localizada em Serra, região metropolitana de Vitória/ES. O estudo foi realizado por meio de monitoramento de perda de massa de amostras expostas deste material e comparação dos resultados com os obtidos através do teste padrão proposto pela American Society for Testing and Materials (ASTM G116, 1999), Wire-on-Bolt Test for Atmospheric Galvanic.

Aug 16, 2017

By Moisés Paulo Teixeira

The use of tailings for the synthesis of new materials is a worldwide concern today. This paper approaches the utilization of tailings of soapstone (steatite) in order to produce ceramics. The results show that the addition of soapstone in a ratio over 20% in the ceramic mass has enhanced the bending resistance of the ceramic samples when they were fired at temperatures of 900°C or 1000°C.

Oct 30, 2017

By Hugo M. Checo

Friction-reducing textures for lubricated mechanisms have received much attention since the advent of microtexturing techniques. In this work we consider the piston ring/liner contact, numerically simulating the rings as they slide against a textured liner. This situation has not been sufficiently analyzed because its numerical complexity is much greater than that of texturing the rings. Further, we consider the actual typical geometries of oil-control, wiper and compression rings, under realistic loads and velocities. The results show the possibility of friction reduction when the texture on the liner is properly designed, identifying starvation alleviation as a crucial intervening mechanism.

Jul 31, 2018

By Nigel Marx

In order to understand (and ultimately to predict) the friction reduction resulting from the use of polymer solutions, the rheological properties of model polymer solutions have been measured over a wide range of shear rates. Both temporary and permanent shear thinning have been observed. By using base fluids of different viscosities it has been shown that permanent shear thinning depends more closely on the shear stress experienced by the fluid than on the strain rate. Hydrodynamic measurements have been made on the polymer solutions using a compliant ball on flat lubricated contact that operates in isoviscous-elastic conditions. The measured friction values can only be predicted with reasonable accuracy if the measured shear thinning properties of the lubricant are taken into account in the hydrodynamic model.

Jul 31, 2018

By Patrícia Mundim Campos Faria

The process of particle size reduction by grinding is inherently inefficient and involves high capital and operating costs. In particular, ball milling is one of the important unit operations in the iron ore pelletizing process. The mill product, due to its physical properties, determines the efficiency of subsequent stages of classification, filtration and pelletizing, thus impacting the quality of iron ore pellets. The work demonstrates the application of the population balance model in the optimization of a full-scale ball mil circuit grinding pellet fines with the aim to evaluate the optimal solids concentration to improve iron ore pellet quality. Initially, detailed experimentation was carried out in a 25.4 cm diameter batch mill and a relationship for mill scale-up using a linear population balance model in wet grinding systems was established. The selection and breakage parameters and the specific selection functions were determined for pellet feed iron ore. It was possible to identify the non-normalizable nature of the breakage functions of the ore studied, which were modeled properly. Afterwards, as a result of incorporating the specific selection functions and breakage functions into the linear population balance model, it was possible to predict product size distributions in the pilot and plant scale mills (0.416 and 5.18 m diameter, respectively) from data obtained in the 25.4 cm diameter mill. Finally, with this scale-up procedure it was possible to appraise the plant scale optimization via laboratory scale grinding mill tests. The effects of changing percent solids were assessed in order to improve the industrial mill performance and the optimal value should be in the range from 76 to 80%.

Aug 1, 2018

By Leonardo Camilo dos Reis, Edmilson Fernandes Dadomi, Claudio Silva de Paulo

In the hot strip mill production, one of the factors that may affect the productivity is the occurrence of failure due to the geometry of the strip at the exit of the rolling mill, because the tip of the strip can turn-down or turn-up. This study had the objective of evaluating the behavior of the strip when leaving the working rolls, through numerical simulation, aiming to know the influences of the main variables that govern the formation of the turn-down. The methodology consisted in performing the computational simulation of the strip mill and to vary the operational and geometric parameters that could influence the process. The results showed that the rolling of hot strips of HSLA material with final thickness varying between of 3 to 6 mm and a reduction of 6.6% to 11.0% in the last stand of a hot strip mill, tends to bend towards the roll with larger diameter, higher friction coefficient , higher temperature and lower limit of material flow. It was observed that the variation in diameter is the main factor that contributes to the formation of the curvature of the front-end of strip. Based on these results, several measures were implemented in the industrial line, with a significant reduction in the occurrence of turn-down.

Oct 2, 2019

By Masakazu Iida

In this article, technologies of unburned Al2O3-MgO (UAM) refractories are demonstrated in terms of microstructure evolution. During operation, Mg2+ diffuses from MgO to Al2O3 through the liquid phase to form spinel (MgAl2O4) network. Molten slag tends to penetrate along the voids in the spinel network structure and spinel dissolves in the penetrated slag. Therefore, maintaining a high degree of spinel saturation in the penetrated molten slag is important. In order to achieve the condition described above, suppression of overall mass transfer through penetrated slag is effective. This is achievable by evolution of complicated spinel network structure with small pore diameter, which increases the flow resistance of molten slag. Thus, optimization of refractory composition and fabricating conditions, with the aim of creating on improved spinel network, is essential. The effectiveness of spinel network improvement was validated by commercial applications. According to the investigation of UAM brick after use, further densification due to heating under restrained conditions was recognized. Hence, it was concluded that the evolution of the spinel network structure in UAM refractories is essential technology needed to improve durability.

Oct 30, 2017

By Steven George Jansto

The hot ductility behavior of different microalloyed steel chemical compositions was examined simulating the thermal and strain conditions through the straightening or unbending section of the continuous casting machine. All samples were obtained from industrial slab casters ranging from 200 to 300 mm in slab thickness from steel mills throughout the world including China, Brazil, North America and Europe. The slabs were crack-free and hot rolled into prime quality products. No laboratory heats were tested. Although these microalloyed steels exhibit inherently lower hot ductility behavior, as measured by percent reduction in area at elevated temperature, these steels still exhibit sufficient ductility to satisfactorily meet the unbending stress and strain gradients existing in the straightening section of most casters. The majority of the published hot ductility data, as measured by % reduction in area (%RA), were based on laboratory heats and hence, are inaccurate in accessing the propensity for slab cracking on an industrial caster. This situation then results in invalid conclusions for different chemistries. This research has determined the minimum required %RA for crack-free casting is significantly lower than results based upon previously published laboratory generated data. For example, the literature quotes 40% RA minimum for Nb-bearing steels when in fact as low as 10% minimum RA is more than sufficient to assure crack-free casting based upon the extensive testing and analysis performed in this study. Instead of %RA, the measurement of strain energy has been introduced to evaluate hot ductility behavior. It is concluded that strain energy is a better measure of hot ductility behaviour than %RA. There is considerable value in the evaluation of the hot stress and strain curves, process metallurgy parameters and their relationship to slab quality instead of just basing hot ductility decisions on simple %RA measurements.

Aug 16, 2017

By Pierre Montmitonnet, Yukio Shigaki, Jonatas Mezêncio Silva

A precise roll stack deformation model of a flat rolling mill is crucial for strip profile assessment as it depends strongly on the roll’s deformation. The need for more and more advanced products with stringent both geometrical and mechanical tolerances (e.g., Advanced High Strength Steels – AHSS), with thinner and harder steel strips, demands more advanced simulation models. The present paper addresses assumptions made in Finite Element Method (FEM)-based roll stack models on some important, yet barely discussed features: What is the impact on precision of the simplifications such as symmetry and anti-symmetry? Should roll neck boundary conditions in bearings be considered as fixed or simply supported? In this paper a hybrid model developed by the authors for a general flat rolling mill is used to assess those questions. This model runs much faster (100x in some cases) than a whole-FEM-modeled 6-high rolling mill with the elastoplastic strip deformation, thanks to its simplifications adopted. This model assumes a steady state rolling condition, and the roll stack is modeled with tridimensional finite elements, and the loads are calculated via a slab method adopting a plane strain state for the strip deformation (especially true for thin strips). An industrial 6-high cold rolling mill is modeled and results on the application of symmetries and different boundary conditions on the roll’s necks are presented. It is concluded that the application of symmetries and anti-symmetries for the 6-high rolling mill is possible for thin strips. And the way the necks are modeled does not impact on the final strip shape, though it influences the magnitude of the roll’s displacement. The coupling of the strip with the work roll applied assuming a symmetry plane of the arc of contact has little influence on the strip shape.

Oct 1, 2019

By Zou Zhongpping

Under the new normal state, blast furnace outputneeds to be adapted to the market demand, however the limitation in blast furnace output has significant impact on blast furnace operation and is prone to cause inactive furnace hearth and higher fuel ratio. To address such problems, some practices to maintain stable and smooth operation of blast furnace in case of output limitation are proposed based on data analysis philosophy, which allows the blast flow and hence the top pressure to be determined based on the hot metal output, and adequate kinetic energy of blast supply can be assured by adjusting the tuyeres. Matching between the oxygen enrichment and the pulverized coal injection is also proposed based on theoretical flametemperature, and burden distribution cycle calculation method is proposed, whichoffersnew approach for analyzing the change in burden distribution pattern.

Oct 30, 2017

By Nestor Cezar Heck

Aim of the present work is to continue the theoretical evaluation of the slags of the fundamental system CaO-SiO2-CrOx-MgO (Ca-O-Cr-Si-Mg quinary system) at the temperature of 1,873 [K], with the help of a computational thermodynamic tool. Driving force for this and the previous research works is the understanding of chromium losses from the molten bath into the slag. Especially motivating is the presence of solid phases in the slag, since they may prevent refractory degradation and help in the production of foaming slags. Nevertheless, Cr-bearing solid phases can lead to Cr losses, being therefore detrimental. Determination of the states of thermodynamic equilibrium for this system using a slag with fixed composition as a start material were made using MgO amount as variable. Results show the impact of the MgO content on the equilibrium phases (molten metal, liquid slag, solids) and their composition for this system.

Jul 30, 2018

By Božidar Šarler, Umut Hanoglu

A rolling simulation system has been developed to calculate the macroscopic rate of deformation, stress, strain, and temperature fields by using a novel meshless method. The model is based on two-dimensional traveling slice assumption. The slices are aligned towards the rolling direction. The initial size of the billet, bloom or slab and the geometry of the grooves at each rolling stand, the distances between the rolling stands, and continuous or reverse rolling can be arbitrarily considered. The purpose of this paper is to complement these development by predicting and visualizing also the grain size of steel over the strand cross-section for each position in the rolling mill. The grain size models have been in one-way coupled to the macroscopic calculations. First the critical strain for dynamic recrystallization is being checked. If the calculated strain is higher than that, considering also the time for meta-dynamic recrystallization, dynamic or meta-dynamic grain size calculations are carried out. If the strain is too low then only the static recrystallization is considered together with its required time. Finally, austenite grain size and ferrite grain size are calculated respectively as the steel cools down. The listed physical models are based on collection of empirical relations found in literature. The user of the system is free to choose or create the model he wants with his own parameters. The simulation system has been coded as a user friendly computer application for an industrial use based on C# and .NET framework and runs on regular PCs. The computational time for a rolling simulation is usually less than one hour and can thus be straightforwardly used for optimization of the rolling mill design in a reasonable time.

Oct 1, 2019

By Simon Chiartano

A global reflection on the design of blast furnace main runner was investigated in this paper. TRB Company used its skills and expertise to understand what the best option for this sensitive component is, including some innovative tools: intelligent block design for safety lining, thermal & thermomechanical numerical simulation, immersive measurement by thermocouples, IR thermal camera, 3D laser scanner.

Oct 1, 2019

By Piotr Kula

Vacuum carburising with pre-nitriding (PreNitLPC® technology) involves feeding ammonia during the charge heating stage before carburising. The purpose is to restrict the growth of grain in the surface layer of the carburised steel. The article presents the influence of nitrogen on restricting austenite grain growth during vacuum carburising and on mechanical properties (fatigue strength, impact resistance) of layers that underwent such treatment in comparison with traditional carburising methods.

Aug 16, 2017

By Marjorie Benegra

This study aims to compare the wear resistance assessed in rubber wheel abrasion test of nickel aluminide coatings deposited by for Plasma Transferred Arc (PTA) and High Velocity Oxigen Fuel (HVOF) manufacturing, using the same raw material. A nickel aluminide powder was atomized and deposited on 316L steel plate substrate. After deposition, some specimens were submitted to a heat treating (1200 °C for 24 h followed by 760°C for 24 h). The coatings deposited using PTA developed different microstructures due to the incorporation of substrate elements, its performance was better than the HVOF coatings, although their Vickers hardness was similar. After heat treating, a significant variation in hardness and wear resistance was observed. For PTA specimens, there were decrease in hardness of 35%, while for HVOF ones this drop was approximately 20%. Nonetheless, the effect of thermal exposure in wear resistance was quite different: an increase of 21% was observed for HVOF coatings, while a reduction of 20% occurred in PTA ones. Microstructures modifications in PTA coatings were significant for their wear resistance. On the other hand, the reduction of porosity and sintering were responsible for a better performance of heat-treated HVOF coatings.

Jul 31, 2018