Search Documents

By Jos. R. Guiteras

This paper is one of a series published by the Bureau of Mines on mining and milling methods and costs. It describes operations in the Alma district of Colorado in September 1937, supplemented by some additional data collected in July 1938. ACKNOWLEDGMENTS The author wishes to express his appreciation of the friendly cooperation extended him by the mine operators in the district. The greater part of the information was obtained from mine and mill superintendents to whom individual acknowledgment is made in the text.

Jan 1, 1940

By J. Ran

"Hangingwall sloughing is the major cause of unplanned stope dilution in open stope mining. Understanding the hangingwall sloughing mechanism can guide the stope design in minimizing the unplanned dilution and improving muck size and therefore mining efficiency. Though the modified stability graph method may be adopted to assess the hangingwall stability, for mines where the hangingwall is inaccessible, the required parameters are difficult to define and some of the simple influential factors cannot be easily identified in this method to provide guidelines for stope design.This paper identifies the main modes of hangingwall sloughing in open stope mining based on detailed data collected from mined-out stopes and site observations, applies the voussoir beam notation to analysis of the hangingwall sloughing mechanism, compares the model analysis results with the collected stope data, and provides guidelines for stope design and model application. Finally, examples are given to demonstrate the time and support effects on hangingwall sloughing and stope dilution."

Jan 1, 2002

[COUNCIL FOR 1991/92 President R.D. Beck President Elect JP. Hoffman Vice Presidents Senior Junior Dr H. Scott-Russell J.A. Cruise Immediate Past President Honorary Treasurer H.G. Mosenthal J.A. Cruise Members of Council Dr N.A. Barcza G.A. Brown B.R. Broekman Prof. RJ. Dippenaar B.R. Fleetwood* J.S. Freer P.R. Janisch P.J. Knottenbelt Dr J. Lurie R.P. Mohring *Co-opted K.C. Owen P.D.K. Robinson D.A.J. Ross-Watt P. Smith K.A. van Gessel DJ. van Niekerk P. van Schaardenburgh* CJ.C.J. van Vuuren* P.M.T. White]

Jan 1, 1992

Improved Process & Practices Result In: ? Reduction of undesirable downtime, & expensive secondary damage ? Improved equipment performance & health ? Extension of equipment life, & reduction of operating costs ? Safety and environmental performance improvement Equipment knowledge capture and consistently applied

May 1, 2010

By R. Chen

Most tunnels built in Sydney encounter similar ground situations; they penetrate either the Hawkesbury Sandstone or the shales that lie beneath the city. Tunnels in these materials are generally sup-ported by rock bolts in combination with a shotcrete lining. A method of analysis is presented to improve our understanding of the long term behaviour of fiber reinforced shotcrete (FRS) materials and the tunnel support systems. A finite element method SAFEA (Semi-analytical FE Analysis) is developed to model the combined creep behaviour of a shotcrete lining and the Hawkesbury Sandstone. To model the time-dependent creep behaviour, the bulk modulus and shear modulus of the materials are represented by logarithmic functions in time. A Laplace transform is then applied to these functions of time and the solution of the problem found from a finite element analysis. Tablot?s method is then used to invert the transformed values and find the solution in real time. The time dependent creep deflection of the numerical tunnel models reflects the interaction of the shotcrete lining and rock which have different creep parameters.

Jan 1, 2008

This paper briefly describes the shaft, including sinking, steel sets and their installation, shaft equipment and winders.INTRODUCTIONThe New Broken Hill Consolidated Ltd. Service Shaft is a vertical concrete-lined circular shaft, 20 ft. in diameter with -steel sets spaced at 12-ft. centres. The diameter of 20 ft. was established as the minimum that would enable the shaft both to house the proposed hoisting and service equipment and to satisfy ventilation requirements as a downcast airway. The 12-ft. set spacing was based on South African practice in similar types of shafts.The shaft extends from the surface to 28 ft. below No. 22 Level, a total depth of 3,194 ft. Sinking was commenced in September 1946, and equipping completed in January 1955. Initially the shaft was sunk and concrete-lined to a depth of 52 ft., using a stiff-legged crane and clam-shell grab for mucking. Operations were suspended at this depth to allow the installation of the steel sinking head-frame, winders and ancillary equipment.Sinking and concreting were recommenced after four months and continued to a depth of 1,035 ft. 6 in., where the shaft connected with a pilot opening. The concrete lining was poured as sinking progressed and was piped from the surface to this depth, after which all concrete was lowered in buckets and discharged through a distributor suspended in the shaft. A cycle of stripping to the pilot opening and concreting was continued until the shaft reached No. 22 Level. From this level the remaining 28 ft. was sunk full size. All plats were cut and concreted as sinking progressed.

Jan 1, 1957

By L. A. André Santos

Atmospheric processing of nickel lateritic ores with low costs has been encouraged. In this work the kinetic of atmospheric acid leaching of a northern- Brazilian ore with 1.63% Ni and large amount of fine particles (d50 ≈ 0.075 mm and 40% below 0.038 mm) is presented. Chemical analysis showed a trend of Ni and Fe concentration in finer fraction (−0.075 mm) and Si and Mg in the coarsest one (−0.500 + 0.150 mm) associated to distinct mineral phases. Nickel is widespread in the mineral matrix. Distinct behaviors were observed as a function of particle size associated to the distribution of silicates and iron oxides in the ore. The kinetic modeling indicated that leaching is controlled by porous layer diffusion at 65 °C, but at 95 °C exhibits a mixed control by porous layer diffusion in initial minutes (60 min) and by chemical reaction or diffusion through the pore layer in final minutes (60–240 min) depends on metal evaluated.

By P. J. Hancox

Heavy mineral deposits have been known from Liberia since the1950s from both river and beach placers. The heavy mineral content of beach sands ranges between 28?62% and the suite includes ilmenite, rutile, zircon and magnetite. These occur together with kyanite, sillimanite, staurolite and garnet. The average ilmenite content is 82% with minor zircon (11%), rutile (6%) and monazite (1%). The ilmenite is, however, of poor quality with haematite intergrowths and a titanium content ranging from10?42.4% (average ±25% TiO2). The amounts of rutile and zircon, while of suitable quality, have also previously been deemed too low for economic exploitation.

Jan 1, 2000

By K. Ward

The Environmental Protection Agency (EPA) is beginning to provide compliance assistance visits to various industries, including mining, for Emergency Planning and Community Right-to-Know Act (EPCRA) compliance. The EPA inspectors may consist of a multi-media team deployed to review systems and procedures for EPCRA Sections 302, 304, 311, and 312. The Team’s focus may include emergency response plans, training programs, qualifications of personnel, and release notification protocols. This presentation takes a look at the EPCRA compliance challenges faced by Arizona copper mining and processing facilities.

Jan 1, 2001

Application of the Anaconda Simplified Work Index for Multiple Test Sizes Vale uses Bond Work Index measurements extensively in a number of applications. The Bond Work Index is usually a good parameter for checking scale up procedures when sizing ball mills, as well as the basis for variability analysis whenever drill core data is available. It is typical to measure between 100 and 150 Bond Work Indexes, depending on the deposit characteristics. The Bond procedure is relatively complex and time costly. It also requires relatively large amounts of sample, which are very expensive to be obtained. The benefits of the Anaconda simplified procedure are: considerably smaller sample requirements and laboratory time. This makes it very much attractive at Vale's development centre, including geometallurgical mapping, operation efficiency control, mine to mill, etc. The Anaconda simplified procedure was implemented and evaluated at Vale's Development Centre using a number of ores and several samples of each ore totalling more than 190 measurements. The Anaconda simplified method was calibrated for several test sieves and a correlation for any test size was determined for Vale's test mill. The calibration was also extended for two sample top sizes. The relative error of the simplified procedure was found to be in the range of nine per cent which is within the expected error Bond standard procedure. The implementation of the Anaconda method at Vale's development center has been used with great success over the past years in several green field, brown field projects and operating plants.

Sep 13, 2010

By C. W. Davis

This report follows the same general scheme as did its predecessors; it begins with a dissertation on some phase of ore-testing, continues with results of investigations of ore-treatment methods and of metallurgically important analytical processes, and concludes with an exposition of tests made by established methods on typical ores selected as representative of certain mining districts. One of the first things that is done after an ore has been received is to look at it under the microscope. Microscopic examination serves as an important complement to chemical analysis in interpreting the percentage composition in terms of minerals. If it has been found difficult to treat an ore, the reasons for this action and indicated methods to overcome the difficulties may be ascertained by testing with a microscope. For example, failures in selective flotation have been traced to intimate mineral association and changes in mineral surfaces through incipient oxidation. The importance of surface stains or tarnishes and the presence of adhering slime particles have been found to be responsible for the difficulty experienced in the treatment of certain gold ores.

Jan 1, 1938

By C. W. Davis

This report follows the same general scheme as did its predecessors; it begins with a dissertation on some phase of ore-testing, continues with results of investigations of ore-treatment methods and of metallurgically important analytical processes, and concludes with an exposition of tests made by established methods on typical ores selected as representative of certain mining districts. One of the first things that is done after an ore has been received is to look at it under the microscope. Microscopic examination serves as an important complement to chemical analysis in interpreting the percentage composition in terms of minerals. If it has been found difficult to treat an ore, the reasons for this action and indicated methods to overcome the difficulties may be ascertainedd by testing with a microscope. For example, failures in selective flotation have been traced to intimate mineral association and changes in mineral surfaces through incipient oxidation. The importance of surface stains or tarnishes and the presence of adhering slime particles have been found to be responsible for the difficulty experienced in the treatment of certain gold ores.

Jan 1, 1938

"The mining industry uses many types of mineral and metallurgical plants to produce saleable product from ore mined. Plant design history has left current operations with a mixture of manual operation and various forms of automated process controls. Consequently, we typically see high variability in the continuous operations together with a shortfall in the attainment of full capacity, or higher utilisation of consumables.At a level of best practice, ‘Operational Performance Excellence’ focuses on process control, using automation and control systems to deliver process optimisation. This more sophisticated delivery is a great deal more difficult than the first stage of equipment selection / installation. It includes the appropriate selection of the right instrumentation, control system, key process knowledge, individuals with a solid control engineering background / experience, and the essential backing / support of the operations management team together leading to higher value delivery. Robust solutions can be realised, considerably minimising process variation, thus leading to process optimisation. This approach results in an easier, efficient and safer process while providing considerable returns for the plant owners.How variable are your processes, and do you maintain optimised process performance with dedicated resources, modern instrumentation, ‘best practice’ control systems and performance monitoring tools? In this paper, these questions and their possible answers are discussed."

Jan 1, 2014

By E. J. Matson

From February until July 1943 the Bureau of Mines conducted an exploration project at the Majuba Hill mine to determine tonnage aria grade of the copper and tin ore and to search for extension of the mineralization. The work comprised sampling, long-hole drilling, underground excavation, and ore-dressing test.

Jan 1, 1948

By R J. Johnson

The development of "SANFO" has provided the Mining Industry with a LOW COST HIGH GAS VOLUME, VARIABLE DENSITY, Blasting Agent which can be blended "On Site" in a simple Agitator mixing and charging system by mine site employees.

Jan 1, 1996

By K. J. Stanaway

Major world ilmenite and rutile accumulations reveal similar regional geology and Proterozoic age deeper crustal source rocks. During crustal collision titanium crystallizes as ilmenite and rutile at buried sites of high pressure and temperature rock metamorphism. Hydrothermal activity can convert titanium minerals to rutile, but titanium migration and enrichment seem only local. Many melts crystallize rocks with iron-titanium oxides in solid solution, but titanium enrichment at economic scale takes place in basic intrusive melts often associated with anorthosites and charnokite. Sedimentary placer enrichments have formed since the Proterozoic with water-resistant ilmenite, and rutile segregating by gravity from quartz sands deposited from flowing water. Placers have residual, alluvial, strand and shallow marine variants. Time, organic acids, and sand permeability play lead roles in the leaching of iron from ilmenite during weathering and diagenesis.

Jan 1, 2005

By S. A. Lorentz, Y. Xu, C. Theron

The failure of tailings storage facilities (TSFs) results in the discharge of significant quantities of hazardous waste material into the natural environment. Research studies relating to slope instability have identified physical mechanisms such as rainfall-induced erosion, liquefaction, and shear failure as the main triggers. The generation of transient pressure waves and the mobilization of pre-event water in the unsaturated zone have been found to trigger shallow landslides in natural hillslopes. In this paper we review these physical mechanisms, known as groundwater ridging (GWR) and the Lisse effect (LE), from other studies. Previous researchers have explained both these phenomena through field and laboratory observations, numerical modelling, as well as conceptual discussions. These case studies demonstrate the impact of rainfall characteristics on the generation of transient pressure waves that rapidly increase the phreatic surface and change pore water suction. Reference is also made to the influence and behaviour of physical porous medium characteristics on the establishment of a continuous water phase that facilitates the transmission of an induced pressure head. However, previous studies fail to recognize the possibility that the pressure increase in pre-event water through pore air propagation could cause slope instability in tailings dams. The authors suggest that the physical properties and hydraulic behaviour of unsaturated porous tailings media make it susceptible to GWR and the LE, resulting in the creation of a potential failure plane.

Feb 2, 2022

By S Das

Deposit-10/11A is situated in the iron rich Bailadila region of India comprising haematite ore of average grade 65 per cent Fe. The deposit production line was commissioned in the year 2002 having a capacity of 5 Mt/a. The plant has the state of the art mineral processing equipments.The ore is transported from mines to crushing plant by means of dumpers. The ore is comminuted in two stages to get 150 mm top size product and this product is transported through conveyor system and is stored in silos as feed stock for beneficiation plant. In the beneficiation plant this crushed product is wet screened in two stages to produce a product of lump (-150 + 10 mm) and fines (-10 + 3.15 mm). The product of -3.15 mm top size is fed to primary classifier for a size separation at 150 µm. The resultant product (-3.15 mm + 150 µm) is dewatered and transported to fi ne ore product stock yard through conveyor system. The minus 150 µm material from classifier overflow is fed to cyclones (508 mm cyclone battery with an apex of 65 mm) for desliming at 45 µm and to recover ultrafi nes (-150 + 45 µm). The cyclone overfl ow slimes (-45 µm) along with water is treated in lamella thickeners to recover process water. The thickener underflow material is transported to tailing pond (discharge rate is 300 m3/h at a specific gravity of 1.4) by pumping through HDPE (high density poly ethylene) pipeline and the over flow water is being recirculated. The water requirement for beneficiation is approx 1.5 m3 per ton of ore.This paper aims at identifying and quantifying the factors that affect the overall plant performance (grade and recovery) during the different seasonal variations especially in the rainy season (mid-June to end October). The effect of seasonal variations on unit operations such as milling, classification, thickening and filtration are discussed. Specific cases are presented as examples and recommendations are formulated.

Jul 11, 2011

Diesel Particulate Matter (DPM) is considered carcinogenic after prolonged exposure. With increasing use of diesel-powered mining equipment in underground mines, miner?s exposure to DPM has been increasing. Most studies on the issue has been DPM control measures with few studies on diesel exhaust propagation patterns after leaving the tailpipes. This study uses computational fluid dynamics (CFD) to investigate the airflow pattern in an underground metal/nonmetal mine for a single heading. Several high DPM concentration areas are identified in the study and common practices for compliance are suggested. Airflow and DPM distribution are compared between blowing and exhausting face ventilation systems. Suggestions are also provided for the protection of miners in the face area.

Jan 1, 2009

By K. Kohli

A case study involving a historic structure undermined by longwall mining is presented in this paper. The location of this study is in South Western-Pennsylvania; USA. The structure is 150-years old and subsided 4.5 feet. This paper discusses the mitigation measures taken to reduce the subsidence damage and its effectiveness.

Jan 1, 2002