Search Documents

By Li Keqiang

This paper discusses the pile foundation of tall buildings in Shenzhen region. For 156 constructed tall buildings exceeding 18 storeys, about 86. 5 per cent of the sum. The two main types of foundation used are the semi?machine?bored/slurry drilled cast?in?situ pile and the excavation pile (hand ?dug caisson). The engineering geologiical condition in Shenzhen was analysed. In general, the bed rock level is not too deep. It belongs to hard rock, but the geologic structure is more complex and the tectonic fissures is plenty. According to experiences of the researches, tests, designs and constructions of pile foundation, we present the basic design principle of pile foundations for tall buildings as follows; (1) pile strength control to select the pile type and to choice the cross sectional dimen­sions, must be in compliance with the strength of the pile. (2) bearing stratum strongly weathered, moderartely weathered and slightly weathered rock may be used as the bearing stratum. (3) bearing pile bored /drilled cast-in-situ pile designed as an end bearing pile. (4) friction pile precast concrete pile, prestressed concrete tubular pile and driven cast-in-situ pile designe as a friction pile. In case, pile design is in compliance with these principles, it may be safe, economical and reasonable.

Jan 1, 1991

By M. Potesser

In the past, different furnace types have been developed for use within the copper industry, with two common anode furnace designs typically used in copper smelting plants worldwide: the tiltable reverberatory furnace (KPO) generally used for the secondary copper industry and the cylindrical or drum type anode furnace (TRO) for handling a liquid blister charge generated in primary copper production. The disadvantage of the KPO is its design related to the longer refining period, because of the low bath depth, however it provides good conditions in the melting period due to its large bath surface. On the other hand, small amounts of scrap charged into the TRO increase the melting and dissolution period, but it provides good conditions for the refining period. The newly-developed elliptical furnace concept (TRE) offers the advantages of each of these furnace types. The special design allows melting of the scrap more efficiently than in the KPO and refining the liquid copper more efficiently than the TRO. This paper shows a metallurgical comparison of the three furnace types in regard to the melting period by heat technological considerations (optimized arch design) and of the refining period done by CFD with concentration on current, recirculation and dwell time of the gas in the melt. The paper outlines the possibilities for a reduction of the tap-to-tap time and energy consumption as well as for an increase of the production capacity, which can be achieved by applying the TRE instead of the conventional furnace designs.

Jan 1, 2007

Since the early 1990s it has been evident that electricity demand has outstripped investment in generation and transmission. At the same time, concerns were being expressed about the risks associated with the run down of the Maui gas field. It is axiomatic that the necessary investments firstly require a stable and supportive regulatory and fiscal environment, and secondly that such investments have long lead times. A unwillingness by successive Governments to fund the necessary infrastructure, however, lead to the profound restructuring of the electricity with the ultimate objective of transferring the investment risk from Government to the private sector. Successive power crises since 1992 result from a failure to put in place a regulatory framework necessary to provide the environment to allow the private sector to make the needed investments within the necessary timeframe. The electricity sector has now stabilised to the extent that the regulatory risks associated with generation investment have been reduced. This does not mean that risk has been eliminated, however, and both economic and environmental issues will continue to constrain investment in some power proposals particularly those in the South Island and especially any South Island coal or gas thermal proposal. This is firstly because of several very simple economic issues:  1. while the South Island may have significant coal resources it lacks a significant electricity market; 2. except for a six to ten week period in a dry year, low cost hydro will price any large-scale South Island thermal out of the market which will restrict any large scale thermal station to a dry year and/or peaking load; 3. except for a six to ten week period in a dry year, export capacity on the HVDC link to the North Island is constrained to around 964 MWe (and 482 MWe from North to South in dry years); and 4. construction of any new thermal plant in the northern half of the North Island will price any South Island thermal station out of the market. There are also significant environmental issues associated with the establishment of a large scale thermally based power station in the South Island. Because the South Island lacks any large scale economically proven gas reserves, the environmental constraints considered are those associated with coal production. A coal mine dedicated to power generation will have significant on-site impacts associated, in particular those associated with disposal of opencast overburden and visual impacts. These will, however, be partially offset by the relative remoteness of such sites to population centres. What cannot be offset, however, is the off-site impacts, in particular, CO2, SOx and NOx emissions, water disposal and acid mine drainage.

Jan 1, 2003

SAG Mill Grinding Design Versus Geometallurgy - Getting it Right for Competent Ores Smarter processing for the future, in the area of SAG mill design involves accurate grinding test data, completing final mill design in less than three months, and at a cost of less than US$80 000. More detailed variability testing on the other hand takes longer, is more expensive, and is used for throughput optimisation for an existing or newly purchased mill. This paper shows that SAGDesignTM testing is excellent for new SAG plant design due to relatively low cost per test and the ability to do more testing for a limited budget on larger projects. It also briefly examines a way to develop proper geometallurgical ore hardness information on every block in the mine model, from the more detailed analysis data.

Sep 13, 2010

By William J. Neely

Augercast piles are formed by drilling a continuous-flight auger into the ground and, on reaching the required depth, sand-cement grout or concrete is pumped down the hollow stem as the auger is withdrawn. The sides of the hole are supported at all times by the soil-filled auger, eliminating the need for temporary casing or bentonite slurry. The augercast piling method is fast and economical; there is no vibration, very little noise and, if executed properly, no ground displacements during installation. The method is well suited to sands which are easy to drill and are readily transported up the auger. Relatively little attention has been given to augercast piles in the literature which might be part of the reason for the considerable variations in local practice, building code requirements and design methods. The purpose of this paper is to discuss some of the features of augercast pile installation that are known to influence both the structural and geotechnical capacity of the pile, to evaluate several empirical design methods and to look at some important aspects of quality control of augercast pile installation.

Jan 1, 1990

By W. A. Ahrens, J. H. McNamara, J. G. Franek

"An economical, pollution-free process has been developed for the hydrometallurgical extraction of copper from sulphide ores. The extracted copper, in the form of cuprous chloride (CuC/), is converted by reduction to copper metal. The metal is melted and fire -refined into wire bars which meet the standards of electrolytic tough pitch (ETP) copper wirebars. IntroductionThe successful development of the Cyprus Copper Process has been an evolutionary series of events covering a time span of some nine years. The original process, based on an electrolytic membrane cell principle , was abandoned in 1975 because of technical, economic and pollution problems. During the past four years, the pilot plant has been reconstructed based on a new flowsheet and operated successfully in several campaigns, some for as long as four months. The pilot-plant hydro section operates at a 225-lblhr copper rate. In October 1977, a feasibility study was completed by Jacobs Engineering, Pasadena, California. The study showed favourable economic and technical feasibility. Jacob's studies in 1978-79 revealed favourable comparative economics with other known pyrohydro processes and favourable economies of scale.The Cyprus Copper Process converts copper concentrates of varying composition into copper metal, which has been proven to be equivalent in every way to electrolytic tough pitch copper, suitable for electrical applications. This is accomplished at capital and operating costs which are estimated to be lower than those associated with any other known currently applicable technology. Also, the total energy requirement is equal to or less than any other known process and the process is essentially pollution free."

Jan 1, 1980

By J. F. Myers

A bit of old philosophy: The optimist, the pessimist, The difference is droll; The optimist, the doughnut sees, The pessimist, the hole. This is a neat summation of the viewpoint of those engaged in "treating the crude mineral crust of the earth." Many of those in high places have reminded us during the year of the diminishing supply of the resources so essen-

Jan 1, 1948

The Wongawilli system of mining has been in use for over 30 years and has enabled high production rates and acceptable extraction ratios to be achieved in seams less than 4 m in thickness. A modification of the Wongawilli system has been developed to permit the use of a continuous miner and mobile equipment to extract a coal seam 6 m thick. Following physical and mathematical model studies the new mining method is now undergoing field trials at Collinsville, Queensland. Progress of the field trials to date has achieved 99 per cent extraction of the upper slice by remote control operation of the continuous miner and established the feasibility of installing resin grouted wooden dowels in the coal floor to reinforce the coal septum. The method is explained in the text. Monitoring of the goaf gases as an early indication of spontaneous combustion has been incorporated in the mining cycle by placement of tubes in the goaf as the face retreats and continuous analysis of the goaf gases made at the surface by the National Coal Board tube bundle monitoring system.

Jan 1, 1980

By Janine Feitosa de Deus

Compósitos ambientalmente corretos, fabricados a partir de fibras naturais lignocelulósicas (FNL), estão entre os mais investigados e aplicados atualmente. Dentre as FNL, destacam-se as fibras de Rami (Boehmeria nivea), que surgem como alternativa em sistemas de blindagens multicamadas, para uso em coletes de proteção balística, por serem leves, de baixo custo, resistentes e ambientalmente corretos. No presente trabalho, investigou-se o comportamento mecânico de compósitos de matriz epóxi reforçados com tecido de rami, através de testes de flexão. Compósitos contendo separadamente 0, 10, 20 e 30% em volume de tecido de rami e resina epóxi, foram fabricados em um molde metálico, sob condições de vácuo. Os corpos de prova fraturados foram analisados em MEV e os resultados foram avaliados visando algumas propriedades de flexão com a incorporação do tecido de rami, visando sua posterior aplicação em blindagem balística.

Oct 30, 2017

An effective electrowinning process in hydrometallurgical industry requires fluoride levels in the base metal solution to be less than 10 mg/l. Selective removal of the fluoride ions from base solution is thus desired, if fluoride was added to control calcium and magnesium in the circuit. Consequently, adsorption of fluoride onto activated alumina was studied in a batch and a column set-up. The effects of base metal solution pH, temperature, initial concentration and flow rate on activated alumina performance were investigated in either a batch or column configuration. A two-level factorial experimental design was implemented in studying column dynamics. Results demonstrate that activated alumina is an effective adsorbent for selective removal of fluoride from base solution. In the batch operation, fluoride was removed to values below the maximum allowable concentration (10 mg/[l]) when pH was = 8. In the column adsorption step at 55°C and 600mg/[l] initial concentration, up to 16 bed volumes were processed before breakthrough level was reached. Desorption step using 1% sodium hydroxide solution achieved an elution of 8 bed volumes. The activated alumina (AA) had a capacity of 8.65 gF/[l]AA at the 10mgF/[l] fluoride breakthrough level during the column adsorption test. Keywords: Fluoride; activated alumina; adsorption; recovery; regeneration.

Jan 1, 2009

By Evan J. Owen, Virginia T. McLemore

Rare earth elements (REE) and critical minerals are increasingly becoming more important in our technological society and are used in many of our electronic devices (such as cell phones, computer monitors, wind turbines, etc.), batteries, and magnets. Measuring REE and critical minerals in ashed coal approximates the REE and critical minerals in the fly or bottom ash remaining after coal is burned at a power plant, where REE and other critical minerals could be leached. In New Mexico, there are 26 coal fields in Late Cretaceous rocks in the San Juan and Raton Basins. These rocks are being characterized as part of the DOE’s CORE-CM (Carbon Ore, Rare Earth, and Critical Minerals) program. Higher concentrations of REE (as much as 2103 ppm total REE) are found locally in ashed coals from the basins. More chemical and mineralogical analyses are required to fully understand the distribution and origin of REE in these deposits. As the demand for REE increases because of increased need and short supplies, the dollar value per ton of ore rises, enhancing deposit economics, perhaps even from coal.

Feb 1, 2025

By T. A. Rickard

Freeman, the English historian, said that he had learned from Macaulay "never to be afraid of using the same word or name over and over again if by that means anything could be added to clearness or force. Macaulay never goes on, like some writers, talking about `the former' and `the latter', `he', `she', `it', and `they', through !clause after clause, while his reader has to look back to see which of several persons it is that is so darkly referred to". He might have learned also from Macaulay that a preposition makes a' feeble ending for a serious statement. How often do you hear `the former' and `the latter' in conversation? Good conversation is a guide not to be dis¬dained. When you must use `the latter', do not confuse it with `the last'. Cheap labor, cheap fuel, and cheap transport are essential, the latter [last] being particularly important in base-metal mining. The apparatus may be used to determine such gases as hydrogen sulphide, chlorine, oxides of nitrogen and some others, as well as sulphur dioxide. In the case of the latter two, etc. The two last mentioned are "sulphur dioxide" and "some others". He should have stated which two, and he should have avoided that wretched phrase "in the case of ". Pinning may be partly prevented by use of chalk, oil, or turpentine. The latter [last] is best. I "Partly prevented" is a poor phrase. `Prevented! is a word that does not lend itself readily to modification. He means `checked' or `corrected'.

Jan 1, 1931

By Lewis Blanchard Brown

It is my purpose in the following paper to describe the south-central part of Siberia, with special reference to its geology and the mineral deposits. This region is known politically as the Achinsk and Marinsk districts of the Tomsk Government. It is situated among the Altai mountains, in. ]at. 50° to 55O n and long. 87O to 93O E., not far from the northern frontier of Mongolia, and is divided as follows: Mining Districts.—(1) The Tomsk mining district, including the political districts of Altai (belonging to the private crown lands of the Russian Emperor) and Marinsk; (2) the AchinskMinusinsk mining district, including the political districts of Achinsk and Minusinsk; and (3) the North Yenisei mining district, situated in the northern part of the Yenisei political district of the Yenisei Government. Fig. 1 is a map of the Tomsk mining provinces, showing the useful mineral-deposits, excepting those of gold, and giving the routes of the railroads and post-roads connecting the various districts. Political Divisions.—The Tomsk Government is sub-divided into seven " oojesdy " or districts, as follows: Barnaul; Biisk; Kuznetsk; Kainsk; Kolyvan; Marinsk; Narim; and the Altai district (private land, as above). The Yenisei Government is sub-divided into five "oojesdy" or districts, as follows : Erasnojarsk ; Kansk; Yenisei; Achinsk; Minusinsk. Concerning the geology of the region, in addition to the record of my own observations, references will be made to the works of earlier writers. These have been consulted for the purpose of comparison, as regards the districts which I have actually traversed, and for the purpose of completing my account of such portions as I have not been able to visit.

Jan 1, 1904

By J. Wright

Since the 1960’s toroidal conductivity has been used to determine the Alumina to Caustic ratio of the digester discharge liquor stream. In recent years the application of ceramic materials have allowed the sensors to moved upstream to provide tighter control of the process. In the Bayer process, dissolving the aluminum contained in bauxite ore in caustic soda and converting it to aluminum oxide produces alumina. An important parameter of the process is measuring the alumina to caustic ratio in the digester discharge stream. The A/C ratio at a given caustic concentration is a measure of the degree of saturation of the alumina in the plant liquor. The aim in the process is to achieve a high A/C ratio. There is however a limit where precipitation will occur if the A/C ratio is too high. For many years conductivity has been used to determine the A/C ratio. Conductivity of discharge liquor is related to the caustic concentration. The change in the caustic concentration is in the same direction of the change of solubility of the alumina. Controlling the conductivity through adding additional bauxite ore and varying the dilution flow can increase plant yield.

Jan 1, 2001

The Florida phosphate industry, which supplies about three-quarters of the domestic phosphate fertilizer, produces tremendous volumes of phosphatic clay wastes (slimes). These clays retain a high percentage of water for extended periods of time. The clays also pose an environmental hazard because the disposal technique involves aboveground storage behind earthen dams. Although much research has been undertaken by numerous organizations to dewater slime, no completely satisfactory solution has been developed. In June 1972, a cooperative effort by the Federal Bureau of Mines and the Florida phosphate mining industry was initiated to develop a solution for dewatering the Florida phosphatic slimes. This report discusses various aspects of the slimes problem, reviews past research, makes recommendations for future research, and includes a bibliography of references and patents dealing with the subject.

Jan 1, 1975

By Ish Grewal

The ACACIA Reactor - Introduction What is it? The Acacia Reactor is a fluidized bed high intensity cyanide leaching system. Purpose for its existence? The Acacia Reactor was developed to treat high grade gold concentrates generated from primary gravity concentration systems. Why intensively cyanide leach a gravity concentrate? Current secondary upgrading processes, such as tabling, create significant losses of fine gold that is initially recovered in the primary gravity concentration units. Additional benefits include improved security and a reduction in health hazards associated with calcining.

May 1, 2002

By F. Pagliacci

Retaining walls for the construction of underground urban infrastructures have to be executed considering the impact of a deep foundation job-site within an urban network. Traditional excavation systems, based on the use of grabs and bentonite mud, involve serious problems such as: the opening of trenches adjacent to existing buildings; the cleaning of the working area; the site installation for the production and storage of the bentonite mud; the transport and disposal of soil contaminated with bentonite mud. Alternative solutions have therefore been developed in order to overcome these problems. For temporary works soil consolidation methods, combined with the use of sheet piles, have been implemented, by a combination of traditional mixing methods and jet grouting systems to speed up the operations, consequently reducing the construction time. For permanent works two new techniques named respectively CSP (Cased Secant Piles) and CDW (Continuous Diaphragm Walls) have been studied, applied and tested.

Jan 1, 2000

By L. Bircumshaw

Paper written on project work carried out in partial fulfilment of BSc (Eng) (Chemical) degree This paper details the formulation of a mathematical model for the simulation of a primary bioleach reactor, with specific reference to the leaching of pyrite. The model is based on the direct reaction mechanism, where the leaching of pyrite is said to occur via a two-step process. The process involves the formation of ferrous?iron through the chemical leaching of pyrite and subsequent bacterial oxidation of ferrous-iron back into ferric-iron. At steady state the rate of chemical leaching and bacterial oxidation are linked by the ratio of ferrous-iron to ferric-iron in solution. The extent of conversion of pyrite in the reactor system is described using the segregated flow model, with the exit age distribution of the solid phase being described by the Tanks-in-Series model. The final phase in model formulation involves the inclusion of steady state material balances on the bacteria and fluid phase components. The model is compared to pilot plant data and laboratory data for two different types of pyrite concentrates, with simulation results showing that the model is in good agreement with the data. Author key words: Bioleaching; pyrite; primary reactor; modeling; segregated-flow model; tanks-in series model.

Jan 1, 2006

By Amy McBrayer, Vladislav Kecojevic, Juan David Valencia Quiceno, Dragan Bogunovic

The mining industry’s commitment to innovation reflects a history of adopting technological advancements to enhance workplace safety, environmental sustainability and vocational training. The objective of this research was to develop an augmented- reality (AR) system for heavy-equipment operators (HEOs) in surface mining. The developed system has the potential to enhance mine safety, training and data-driven decision- making, which presents a significant step toward a more sustainable, effective and technologically driven mining training, contributing to the industry’s evolution and growth. The AR training system leverages Microsoft’s Power Platform and HoloLens 2 capacities to provide operators with detailed and immersive training guides for three mining equipment, including bulldozers, motor graders and haul trucks. AR guides combine speech controls, 3D objects, informative images and explicative videos in the real working conditions to enhance the operator’s learning process. The system has the potential to modify the training structure based on user performance and provides an efficient approach to data collection during training. This project was developed and applied through a case study in a surface mine in the Southern United States.

Feb 1, 2025

Editor?s note: Each year, the June issue of Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue. Thank you to the industrial minerals annual review editor, to the technical committees chair and vice-chair, and to the authors of the individual commodity profiles. Jim Norman, member SME, of GeoTrans, Inc., is the industrial minerals annual review editor. SA Ravishankar, member SME, of Cytec Industries, is chair of the industrial minerals technical committees. Technical committee vice chairs include: ? Abani Samal, member SME, of Pincock Allen & Holt, agricultural minerals. ? Aaron McMahon member SME, of Pincock, Allen & Holt, ceramics and refractories. ? Bradley S. Van Gosen, member SME, of the U.S. Geological Survey, chemical raw materials. ? Mark Zdunczyk, member SME, of Continental Placer, Inc., construction materials. ? Jerry Gauntt, member SME, of JEG Minerals Consultants, fillers and pigments. ? Michael Cheshire, member SME, of Indiana University, sorbents, filters and process aids. Their help makes possible this June industrial minerals issue. On behalf of ME readers, the editors thank them.

Jan 1, 2008