Search Documents

A modified liquation technique was developed for recovering tin from tinhouse scruff metal or hardhead containing about 10 per cent iron and 15 per cent occluded flux, palm oil, and moisture. This was effectedby heating the scruff metal to 950°C followed by rapid cooling to suppress the formation of FeSn2 and FeSn, and then subjecting it to the ordinary liquation and drossing processes of refining. By this method it was possible to recover about 83 per cent of the original tin content and, with subsequent smelting of the irony drosses, an overall recovery of 92 per cent was obtained.

Jan 1, 1969

By Wendy L. Mathieson

The Bonneville Power Administration (BPA) will build about 500 miles of new 500-kV transmission lines in the next 5 years. Many new lattice towers will be built in remote locations or in environmentally sensitive areas. Therefore, micropile foundations were designed that could be installed in remote areas, in variable subsurface conditions, and in a manner that would reduce excavation volumes and potential erosion concerns. Typical lattice tower foundation axial loads range between 75 and 1,500 kips (300 to 6,700 kilonewtons [kN]) per leg, with uplift loads being slightly less than compressive loads. Lateral loads range from 5 to 320 kips (20 to 1,400 kN) per leg. Full-scale axial and lateral load tests were conducted in geologically representative soil units during the micropile design for the 9-mile-long (14-kilometer [km]), Kangley-Echo Lake transmission line that extends through a protected watershed east of Seattle, Washington. Micropile foundations for single and double circuit suspension and dead end towers were designed using these load test data.

Jan 1, 2004

By C. J. Lewis

Considerable amounts of the world's known reserves of elemental sulfur are found near the surface in areas of volcanic activity both active and inactive. Because such deposits cannot in general-be mined by the well-known Frasch process, and because other methods of recovery have not proven to be economically competitive except in isolated instances, at present these reserves remain relatively undeveloped. However, projections of world sulfur demand indicate that new sources of marketable sulfur will be needed in future years 2/, 19/. For this reason, recovery of elemental sulfur from these near-surface deposits is of continuing interest. Solvent extraction as an approach to recovery of elemental sulfur from open pit-mined ores of these non-Frasch deposits has received considerable attention particularly at the research and development level 3 /, 7/, l l /, 16/, 21/,23/, 29/ This method has been and continues to be attractive because it presents the potential of high sulfur recovery and purity of product coupled with a relatively simple process flowsheet in which low energy requirements and reasonable operating costs are thought to be possible. However, the physical and chemical characteristics of the native-sulfur ores, of elemental sulfur, and of the known solvents, have presented difficulties in the development of solvent extraction processes. Up to the present time, viable processes have not been realized within the framework of sulfur marketing conditions.

Jan 1, 1970

By W. T. Millar

Field reconnaissance and laboratory tests an clay from South Windsor, Hartford County, Conn., indicate that the clay is suitable for lightweight aggregate raw material. Exploration of the deposit supports the conclusion that the reserves of clay are sufficient for economical mining operations to produce lightweight aggregate. Preliminary tests indicated that the clay has a short bloating range. Initial expansion occurred at 2,000° F, and at 2,100° F the clay was slightly overfired and sticky. Rotary kiln tests verified the preliminary data, and these tests showed that the clay would make a good lightweight aggregate if the processing temperature and the kiln feed sizes were closely controlled. Lightweight concrete made from the processed aggregate had properties comparable to those of concrete made from a commercial clay aggregate.

Jan 1, 1964

By A. Roy MacLean

"Cape Breton is an island on the eastern extremity of Nova Scotia, Canada. Here, coal mining under the Atlantic Ocean has been a way of life since the early French militia mined coal for heating purposes in 1720. Despite many ups and downs over the intervening years, the coal industry has survived and is now in a favourable position to benefit from the upswing in international coal usage.Mining in Cape Breton Early mining in Cape Breton was done by hand picks and shovels. The coal was loaded into mine cars which were hauled by horses to the main haulage system for transport to surface. Later, compressed-air cutting machines and drills led to the use of explosives to blast the coal so that it could be loaded by hand and transported as above. In 1923, longwall mining (by hand) was introduced. In 1950, the Dominion Coal Company developed the Dosco continuous miner in order to mechanize the longwall coal-getting operation. At this time, conveyor belts came into wide-spread use, along with diesel locomotives to haul mine cars from the longwall face to the main transport system. During this period, coal was also mined by conventional mechanized room-and-pillar equipment such as cutting machines, loaders, roof bolters, etc. This system evolved into the use of the continuous ·miners of today, which are employed in the Lingan Mine room-and-pillar section. However, this method is only satisfactory at shallow depths and gradients. For these reasons, almost all the coal in this coal field will be mined by longwall methods. In 1968, the Government of Canada expropriated the assets of the Dominion Coal Company on Cape Breton Island in order to prevent complete closure of an uneconomic industry by its owners. The government created, by an Act of Parliament, the Cape Breton Development Corporation which now operates the coal mines, coal preparation plants, railway, shipping pier and ancillary services (Fig. 2). Since its inception, the Corporation has closed three mines, opened two new mines, is in the process of developing a third new mine, and has invested heavily in the one mine which remains from its previous owners."

Jan 1, 1985

By M. Dworzanowski

The physical beneficiation of iron ore that has a wide particle-size distribution is problematic, regardless of the process applied, whether dense medium separation, gravity concentration, magnetic separation, or flotation. The problem of particle size is further compounded when there is a significant -10 µm fraction. Generally the approach to a wide particle-size distribution is to split into narrower size ranges and treat each separately. More often than not the -10 µm fraction is not treated but discarded. This approach results in a more complicated and expensive flow sheet and the loss of any potential value in the -10 µm fraction. Wet high-intensity magnetic separation (WHIMS) bench-scale test work was conducted on a haematite-rich material with a particle size of -200 µm. What made this material different was that it contained a 60% -10 µm fraction, hence discarding the -10 µm material was not an option. The objective of the test work was to determine how to maximize the recovery of the haematite across the full particle size range. Given the unusual particle size distribution, it was concluded that WHIMS would be the only practical beneficiation route. The -200 +10 µm and -10 µm fractions were treated separately and together under varying WHIMS conditions. For a given concentrate grade, the mass yield obtained was greater when the total particle-size distribution was treated. The inferred optimum conditions, using the same material, were tested on a pilot-scale WHIMS and similar results were obtained.

Jan 1, 2014

By Walter S. Bergholz, Michael L. Schreder

"Since Escondida began operations in fiscal 1991, a series of aggressive expansion projects have enabled market share to be increased and ever larger profits to be realized. This was possible due to the very large size of the ore body and its high grade - averaging 2.7% copper from startup through fiscal 1997. The situation has now changed: ore grade is falling rapidly and is projected to be only 1.55% by 2003. Since revenue is directly proportional to ore grade, while costs are proportional to quantity of ore processed, profits will begin to fall dramatically. The Phase IV Expansion Project is intended to forestall this drop in profits by increasing ore processing capacity by over 85%.The Phase IV concentrator is designed for a nominal capacity of 110,000 MTPD and the key to achieving this value is through the proper design of the grinding circuit. This paper presents the general design criteria for the grinding circuit, as well as a description of the facility.INTRODUCTIONThe Phase IV Expansion Project consists of a new copper concentrator located 8.5 km south of the existing operations, a new tailings disposal and water reclaim system, a new concentrate slurry pipeline to the coast, and added concentrate handling capacity at the port of Coloso. The new concentrator has a nominal capacity of 110,000 tonnes per day (MTPD), compared to the existing concentrator’s capacity of 127,500 MTPD. The Laguna Seca concentrator is based on using the largest and most efficient ore grinding mills now available.The concentrator has been designed for a 110,000 MTPD nominal capacity. The process design criteria for the Phase IV project were established from in-house operating information and from test work. Unlike a green field project, Escondida already had an operating plant and it processes ore from the same pit that feeds the Phase IV plant. It is expected that the current mineralization will be similar for the first 6 years of operation of the new project. Therefore, some of the current plant operating conditions were incorporated directly into the design criteria."

Jan 1, 2004

By Guangqing Zhang

The paper presents results of a systematic study of synthesis of titanium oxycarbide and its chlorination. Titanium oxycarbide was produced by carbothermal reduction of titania in hydrogen, argon and helium. Formation of titanium oxycarbide started at 1200°C in all gases. The reduction was the fastest in hydrogen. Formation of titanium oxycarbide in hydrogen was close to completion in 120 min at 1300°C, 60 min at 1400°C and less than 30 min at 1500°C. Reduction in argon and helium progressed at a similar rate and reached 90-95% after 300 min at 1400-1500°C. The chlorination of titanium oxycarbide was ignited at 150-200°C. Chlorine partial pressure and gas flow rate strongly affected the chlorination rate. Chlorination of titanium oxycarbide produced with carbon to titania molar ratio 2.5 at 235-400°C was close to 100% in 30 min.

Jan 1, 2009

By Ronald S. Conti

This U.S. Bureau of Mines (USBM) report describes various fire-fighting resources available to the mining industry and examines the fire preparedness of four western coal mines. Information regarding fire-fighting equipment indicates that an inadequate maintenance program may cause component failure of fire extinguishers, damage to waterhoses is usually a result of improper care, and foam may be a convenient means of conveying water to the fire. Performance data relative to water nozzles (throw distance) and specific practices to improve the state of preparedness in many of these areas are discussed. Studies also indicated that a high-expansion foam plug, will travel down an entry, with a 1% rise in elevation, 207 m (680 ft) before a plywood stopping separating the generator and plug failed. The advance rate of the foam plug decreased when the entry is dry, requiring more foam concentrate and as the foam spread further down the entry. An examination of the mines showed state-of-the-art monitoring systems were common at the minesites. Fire safety was also stressed, including early detection and rapid response of the miners to evacuate the mine. However, the mines placed little emphasis on performance of water nozzles, or personal protective clothing for the underground firefighters.

Jan 1, 1994

By M Akop, G Phillips, L Elliott

An estimation geologist has many tools in their kit and using the correct one for the job is vital for creating a useful model. Reconciliation is a key step to monitor the performance of a resource model and to ensure the correct tools have been selected and appropriate parameters are set. This paper presents an example of refining the estimation methodology for a Channel Iron Deposit (CID), resulting in an improved model. Rio Tinto Iron Ore (RTIO) CIDs are unique iron ore deposits located in the Pilbara region of Western Australia and contribute a significant volume to the world’s seaborne iron ore market. A problematic feature of these deposits is the irregular dispersion of clay pods that cannot be delineated with confidence within the resolution of the exploration drilling. Resource to grade control reconciliation showed an over-prediction of high-grade material in the resource model. A fresh approach was required to improve grade and tonnage predictions. Historically, clay pods were delineated using traditional wireframing techniques and estimated using ordinary kriging with hard boundaries. The new method utilised indicator kriging to estimate the probability of clay. Probabilities generated from the indicator kriging estimate were used as an additional weighting following the ordinary kriging of grades. Results showed indicator kriging improved global high-grade tonnes reconciliation, however, as expected, it did not improve the spatial prediction of clay. Based on improved reconciliation results indicator kriging has now been adopted as a suitable alternative for analogous CIDs at RTIO. These improvements benefit the mine planning process, but do not replace grade control models.

Mar 22, 2022

By A. K. Snelgrove

At a time when water resource planning is proceeding on a continental scale, such as the proposed $100 billion North American Water and Power Alliance, which would redistribute water among three nations, including seven provinces of Canada, 35 of the United States, and three States of Mexico, the selection of a single river basin for study may seem to require an apologia. None is offered because of ( 1) the magnitude of the Indus , itself a part of the great Indo-Gangetic Plain drainage system, with Himalayan sources, upon which the thickly populated northern sub-continent of Indo-Pakistan depends for agriculture and hydroelectic power; (2) the extraordinary problems created by dismemberment of the world?s largest irrigation system through legal beheading of the Eastern Waters under the Indus Waters Treaty of 1960; and (3) the herculean effort to contain the twin encroachments of waterlogging and salinization in a basin which faces a shortage of fresh water. The British irrigation system of barrages and canals on the Indus was a venture admirable in conception. Unfortunately, it is now a legacy burdened with unwanted consequences, due to interference with the hydrological regimen, particularly the rise of water table occasioned by leakage.

Jan 1, 1967

By Jean-Claude LeRoy, Herman Keller

"INTRODUCTIONEROCON's work is the reclamation of mine wastelands. It has had considerable experience in particular in the reclamation of gold mine tailings in the Canadian Shield since the latter part of the sixties when most gold mines were closing down.A typical example is the famous Hollinger Mine in Timmins which produced $566 million worth of metal from 1910 to 1968 and had left behind some 56 million tons of tailings covering about 1,000 acres which were reclaimed on very short order and are now lush meadows of agricultural quality.To date, practically all gold mine tailings have been reclaimed once and for all by establishing a permanent, self-sustaining and maintenance free vegetation cover.RECLAMATION & THE MINING TOWNSThe first appreciation of people in a mining community where the tailings have been revegetated will be noticing one day the elimination of dusty conditions that used to arise formerly on every dry and windy day. In that respect, EROCON encourages not only vegetating the tailings but also the immediate surroundings of the mills and plants themselves at active mines. The elimination of windborne dust will result in an appreciable decrease in maintenance costs of plant and machinery and more pleasant working conditions for all."

Jan 1, 1975

By K. E. Brown, J. P. Brill, A. R. Hagedorn, T. C. Doerr

A recent correlation for multiphase vertical flow by Hagedorn and Brown1,7 has been used to examine the effect of numerous variables such as pipe size, gas-liquid ratio, liquid flow rate, liquid viscosity, liquid surface tension, oil API gravity, water cut, etc., on flowing pressure gradients. Most previous correlations were derived by using a form of the general energy equation which assumed negligible changes in kinetic energy. Under certain flow conditions this can lead to serious errors in predicting pressure traverses. Examples of traverses calculated both with and without the kinetic energy term are included here. The Chew and Connully correlation for calculating changes in viscosity with changing pressure and temperature has been extended so that the effect of a changing viscosity with depth on pressure gradients can also be predicted. Examples illustrating the effect of tubing size show the importance of this correlation in determining pipe sizes for initial well completions. Limitations on production rates in small pipe sizes from excessive friction losses can be predicted with greater accuracy. The combined use of a vertical-flow correlation with a horizontal-flow correlation provides a method for determining the maximum flow rate possible from both flowing and gas-lift wells. Examples are included to illustrate application of the combined use of vertical and horizontal-flow correlations in optimizing production rates and minimizing excessive costs from over injection of gas in gas-lift wells. INTRODUCTION The problems of multiphase vertical and horizontal flow are immediately encountered in any producing well. Fig. 1' shows three stages of production: flow in porous medium, vertical flow and horizontal flow. All three stages affect the production rate from a well. If we are confronted with a particular well and consider only the variables involved in the vertical and horizontal stages of Fig. 1, we should be capable of calculating the flowing bottom-hole pressure necessary to produce a particular flow rate. A change in any of the variables results in a new solution to the problem. Recent approaches in developing horizontal and vertical-flow correlations have improved to the extent that the solution can now be obtained with more confidence than previously. VERTICAL AND HORIZONTAL FLOW CORRELATIONS Since Poettmann and Carpenter's' original work in multiphase vertical flow, there have been many additional vertical-flow correlations developed which have greatly improved the accuracy of pressure-loss calculations. These

Jan 1, 1967

By Carl Belser

This report is the first of a series dealing with the oil-shale reserves of the Green River formation in the Rocky Mountain Region. The known oil-shale reserves of northwestern Colorado at present considered to have economic value apparently are confined to the Piceanco Creek basin between the Colorado and White Rivers. The number of sampled sections is small, but there can be little doubt that the Piceance Creek basin is a potential source of enormous quantities of liquid fuels and the related byproducts obtained from oil-shale processing. The partly blocked and inferred oil-shale reserves of 25-gallon-a-ton shale are estimated to have an oil yield of 125 billion barrels and the reserves of 15-gallon-a-ton shale are estimated to have an oil yield of 494 billion barrels. The number of available sampled sections is inadequate for making firm estimates.

Jan 1, 1951

By Sara Swiokla Korsikas, Toren Olson, Amado Guzman, Yuri O. Zepeda P

Ore agglomeration has been used as part of the heap leaching process for the last 40 years. However, industrial experience shows that the lack of a universal agglomeration standard has limited the benefits of this, otherwise, valuable unit process. The more complex the ore, in terms of the nature and relative abundance of fines (<74 μm), the more important that the agglomeration product satisfies some minimal requirements. This paper presents an agglomeration scale that identifies the quality standards for agglomerates and documents the resulting mechanical, physical, and hydraulic (hydrodynamic) behavior associated with each level on the agglomeration scale. The hydrodynamic properties of an agglomeration product are critical for the proper design of a leaching operation and, as shown in this paper, can be used to select the optimal pretreatment method for a given ore sample. Agglomeration as a unit process not only allows better conditioning of the hydrodynamic behavior of the ore but also creates an opportunity for optimized delivery of reagents to kick-start the leaching process which may ultimately improve the economic performance of leaching. Industrial case data is used to demonstrate the shortfalls associated with low-quality agglomeration and the benefits of improved agglomeration which range from enhanced porous structure (better percolation and drainage characteristics) to better metallurgical response (faster kinetics and higher metal recovery). Proper agglomeration has been used to render otherwise untreatable ores into valuable leaching resources.

Feb 9, 2024

By Jan E. Nesset, Phillip J. Mackey, Joo Y. Kim, Giovanni Di Prisco, André R. Laplante

Understanding the appropriate gold recovery to associate with copper recovery when assessing laboratory testing on porphyry deposits is often complicated by several factors including variable and/or complex mineralogy, and the variability contributed by the low Au content of the various flotation products. As a result, gold recovery is often underestimated and the value contributed by the gold to project economics is less than it should be, a problem that could influence overall project viability. Typically, for these types of deposits, the gold recovery is found to be lower than the copper recovery. In this unique project, having the objective of seeking a better understanding of gold recovery relative to copper recovery, mill feed samples from a selection of six operating world-class Cu-Au low-grade deposits were collected along with the mill metallurgical results for the corresponding sample periods. The samples were subjected to laboratory flotation tests, as well as the Laplante gravity recoverable gold (GRG) test, mineralogical assessment and cyanidation leaching. The aim was to better understand the copper and gold recovery relationship, the links between laboratory and plant flotation performance, the influence of mineralogical differences, and the potential for enhancing gold recovery by gravity recovery techniques. A new correlation of copper and gold recoveries based on the results is presented in the paper. The results showed that the link between copper and gold recoveries established in the best laboratory tests were maintained in the plant results, and further, that the potential for improving Au recovery by gravity or flash flotation methods is directly proportional to the amount of gold greater than 75 microns.

Jan 1, 2005

By Sidney H. Haughton

WHEN the white pioneers of the eighteenth and nineteenth centuries advanced from the coastal settlements of southern Africa into the interior of the subcontinent, they found it inhabited, more or less sparsely, by brown or black peoples mainly of pastoral habits but equipped with a fighting spirit and certain fighting weapons. Some of the tribes were smiths, others were miners and metallurgists; all used fuel, either industrially or domestically. Some of that fuel was wood, some cattle dung, and in some places the natives mined outcrop coal. Coal was first discovered by Europeans in Natal about 1840. After proper deliberation and after allowing due time for a consideration of all the implications, the Natal Government decided in 1881 (40 years after) to import an English expert to investigate and report on the discovery. Things then moved rapidly, and in what to a geologist is the remarkably short space of eight years, Natal collieries were producing at the rate of nearly 30,000 long tons per annum or 100 long tons per working day!

Jan 1, 1945

By Valois R. Shea-Albin

Ground control problems are an important factor affecting safety, production, and efficiency in underground coal mines. A major portion of ground control problems encountered in underground coal mines can be attributed to geologic features in the strata surrounding the extracted coal seam. The U.S. Bureau of Mines has compiled information from numerous sources on the geological features that contribute to ground control problems in underground coal mines. The compilation includes (1) sedimentary features such as paleochannels, crevasse splays, clastic dikes, mold-and-cast structures, concretions, and lithologic factors, and (2) structural features such as folds, fractures, joints, cleat, and faults. The compiled information will aid in identifying the features, predicting their occurrence in advance of mining, and controlling or minimizing roof failure when these features are encountered in an underground coal mine.

Jan 1, 1993

By Michael G. Pojar, Peter G. Chamberlain

Solution mining, primarily by heap leaching, has emerged as an important method for mining gold and silver in the United States. Heap leaching offers many economic and environmental advantages over conventional production techniques, in particular for lean ores and old mine waste rock. In order to more effectively pursue research on heap, dump, and in situ solution mining of gold and silver, the Federal Bureau of Mines conducted an extensive survey of leaching practices and problems. This presentation summarizes trends and statistics. Leaching is projected to provide 20 pct of primary mine produced gold and 10 pct of primary silver by the end of 1982. Current leaching practices in the United States are reviewed; operational problems and research programs to alleviate those problems are discussed.

Jan 1, 1981

By Tony Robles

"A new process is disclosed for the recovery of gold and/or silver values from activated carbon wherein they are adsorbed as cyanide complexes. A unique chemistry allows the new process to use mill process water containing an inexpensive, non-hazardous compound as the eluant. The new process has an elution period of 5 hours at 98°C. The gold in the eluant can be recovered by electrowinning or zinc precipitation. The new elution process is simple, reliable, and provides an eluted carbon that may not require thermal regeneration before reuse. Retrofitting the new process to existing processes such as Zadra, Anglo, and others will not require significant capital expenditures.IntroductionThe efficient and reliable elution process for gold/silver from activated carbon is a very important process in the gold mining industry. The most common techniques for elution of gold cyanide from activated carbon are the Zadra and Anglo procedures.Specialized elution techniques like the Micron and Acetonitrile processes have not been commercialized to significant extent probably due to relatively complex unit operations and expensive reagents.Important functions of the gold recovery circuit are:Efficiently recover gold/silver from the loaded carbon.Carbon is in good condition for reuse for optimum recovery.The pregnant solution is amenable to electrowinning or zinc precipitation to recover gold/silver from the solution.The whole process to be simple and short to reduce gold inventories.Present Elution ProcessesTable 1 shows some carbon elution processes that are available today. The two main elution processes used in the industry are: (1) the Zadra process, in which hot cyanide solution is circulated through an elution column and electrowinning cells; and (2) the Anglo American Research Laboratory (Anglo) process, consisting of a pretreatment step with caustic cyanide solution, followed by elution with deionized water."

Jan 1, 2000