Search Documents

By G. Bonin, A. Jamal, G. Preciado, S. Gillis

"Accurate, easy to obtain, and reliable methods of measurement are the cornerstone of shaft and tunnel developments - during their sinking, operation and maintenance, or in some cases, remediation. This paper presents a new methodology to capture existing shaft conditions in such a manner that they can be transferred from the field to a digital copy, where they can be stored and used for engineering design purposes in a space not directly affected by the costs associated with schedule and equipment performance. The methodology utilizes basic principles of excavation alignment (plumb lines and survey instruments) while adding modern LiDAR, geolocation and survey control tools that can more completely capture the surrounding environment. The complete cycle of collection, processing, and delivery of pertinent information underground can take under an hour. During sinking, capturing data as a live stream measurement and being able to assess the alignment of the shaft liner can be critical to meeting rigid design tolerances. As sinking progresses, small changes in alignment or liner deviations can be captured and immediately corrected. Likewise, post-construction as-built conditions can be recorded and digitized, which will allow the mine personnel to compare the proper working condition to the actual condition years later. Observed changes can be identified and planned as future shaft repair works. This methodology has been developed and successfully deployed during the on-going sinking works of the two shafts at the Jansen Potash Project in south-central Saskatchewan and is described in greater detail in this paper.INTRODUCTION Light Detection and Ranging (or LiDAR) scans of the BHP Jansen Production and Service shafts during construction identified sections of both shafts where the internal radius of the temporary primary liner was insufficient to accommodate the tolerances of the permanent liner that was to be installed inside the temporary liner. These locations are referred to as “tights”. The “Tights Removal Program” was designed to collect high resolution point clouds of the shaft, using stringent survey control, that could be compared to the design profile to generate a heat map of locations for removal of up to 75 mm of steel-fiber-reinforced, 70 MPa concrete liner. This work was all on critical path, which made it valuable to save time on the schedule. Because concrete removal was a time-intensive task, it was essential to locate and remove only the concrete that would encroach on the planned permanent liner, while attempting to maximize the amount of cutting time. Removal was carried by a road header attached to a Brokk(R) 160, a small multi-attachment demolition machine."

Jan 1, 2019

By A. J. Hyett

Due to the ongoing revolution in electronics and communications more cost-effective geotechnical instruments can be manufactured using digital technology. This new generation of digital instruments have embedded microcontrollers that provide highly accurate and reliable measurement of geotechnical behaviour in real world units that can be immediately interpreted. Digital measurements can be transmitted across existing mine-wide wireless communication networks, interfaced directly with infra-red enabled PDA?s or PC?s, and parsed to memory by low-cost data-loggers.

Oct 1, 2004

In referring to two subjects of interest to the Members of this Australasian Institute of Mining Engineers, I would at the outset desire to express our gratification that to-day we are able to welcome as now united with ourselves, those members who until recently constituted the New Zealand Institute. It is hoped that the amalgamation so amicably arranged may be productive of the best results to all concerned, incorporated as this combination has been at the moment of the fulfilment of that greater political union, the Australian Commonwealth.Since last Annual Meeting held in Brisbane, we have come under the same roof as the Chamber of Mines of Victoria, and we entertain the hope that as that Chamber and this Institute possess so many interests in common in the encouragement and advancement of mining and metallurgical progress in these colonies, that much mutual benefit will ensue. There are many directions in which each body can assist the other, and I trust that a friendly co-operation will be maintained.It is gratifying to feel that in all the colonies a distinct movement is being made to increase the facilities for education in Mining and Metallurgy but if I may refer to our colony of Victoria in particular, we have to express the profound regret that in the means of education in the higher branches, we occupy an inferior position, and it is quite certain that we will continue to do so unless the Government is prepared to subordinate provincial considerations to the weightier.

Jan 1, 1901

By M Quinteiro, Å Sundqvist

What is special about being a female mine manager? We do not believe that the challenge is greater for women in managing a mine compared to managerial positions in other male-dominated businesses. The challenge lies in the fact that it is a male-dominated business. Being a leader belonging to a minority creates a situation where competence not only lies in having technical knowledge or general leadership characteristics, but also in acquiring an understanding of the male norm and being able to behave and communicate effectively in the organisation.In order to move towards a better gender balance at senior levels it is important to set measurable objectives on desirable proportions between women and men at management levels within the company. Focus and action are required to achieve this goal. At LKAB, the current target is to reach 25 per cent women in the total workforce by 2020. To date, LKAB has reached 19.4 per cent women in the total workforce, and the number of women in management positions is 19.9 per cent.It is of vital importance to create a non-discriminating working environment to achieve equal opportunities at the workplace, to be able to use the whole workforce as a resource for recruitment of professionals and managers, thereby improving decision-making, productivity, efficiency and profitability.Women as mine managers is not a utopia, but rather an effect of long-term investments in actions that result in equal opportunities for all employees.CITATION:Quinteiro, M and Sundqvist, Å, 2016. Women as mine managers – a utopia?, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016) , pp 43–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By S. Klingmann

ABSTRACT In this paper, we used data collected from the Gibraltar mine to analyze the effect of the TyreSense tire monitoring system on tire performance by reducing tire wear and preventing premature tire failure or damage. We analyzed the relationship between tire temperature, tire pressure, and tire failure or damage to help better understand the importance of controlling high tire temperature and pressure. The results enhance and expand the knowledge of the management of tire operational pressure and temperature.

Jan 1, 2014

IN 1906, soon after his arrival in New Zealand, a brief article was prepared by the writer on "The Salient Features of the Economic Geology of New Zealand," for the Journal of Economic Geology. In November, 1907, a somewhat similar paper, entitled "The Mineral Wealth of New Zealand," was read at the Royal Colonial Institute in London. The present contribution to the Transactions...

Jan 1, 1909

By Wm. O. Vanderburg

This report on the mining and milling of tungsten ores is the second part of a general study of the domestic tungsten industry. The first part, comprising general information on tungsten, has been printed as Bureau of Mines Information Circular 6821. The purpose of these papers is to increase efficiency in the mining, preparation, and utilization of the tungsten resources of the United States. The tungsten industry forms so small a part of the vast mining and metallurgical operations of the illation that private metallurgists have not had enough inducement to give special attention to the recovery of tungsten minerals from the ores, and many of the small companies are financially unable to undertake research work. A study of the milling of tungsten ores reveals that further improvement is possible, especially in the treatment of slimes. Recent experimental work by the Bureau shows that the flotation process is applicable to certain tungsten ores. The future of the tungsten industry it the United States depends to a great extent on utilization of the low-grade deposits of the contact-metamorphic type.

Jan 1, 1935

By Robert B. Parsons

"Recent amendments to the so-called ""flow-through share"" rules in our income tax legislation have given a new lease on life to this once popular investment vehicle.The original ""Dome funds"" for exploration in the Beaufort sea recognized the usefulness of flow-through share arrangements, but, by and large, flow-through shares have until recently not been able to compete effectively with other tax shelter instruments-mainly , limited partnership interests.This month, Tax Notes examines the new tax rules for investing in flow-through shares.IntroductionRecent income tax amendments have helped to rekindle investor and industry interest in so-called ""flow-through shares"" as a mechanism for mobilizing funds toward mineral exploration and development activities. In competing for investment funds, flow-through shares have historically placed a distant second in terms of investor popularity, being unable to compete with the more attractive features of limited partnership arrangements. However, primarily as a result of favourable changes to the income tax law, flow-through shares may be well poised for a comeback.This article examines the income tax considerations pertaining to issuing and investing in flow-through shares, and compares the former and the new income tax rules relating thereto. Of course, inasmuch as a flow-through share issue can involve various contractual arrangements between the investor and the issuer, there is a wide range of legal and business factors that generally have to be taken into account. A discussion of these matter s is beyond the scope of this paper, which is restricted to a summary of the special income tax factors attributable to flow-through shares."

Jan 1, 1983

By F. Cihangir, A. Kesimal, K. Karaman, B. Ercikdi

Uniaxial compressive strength (UCS) and shear strength parameters(cohesion and angle of internal friction, Cand F) of rocks are important parameters needed for various engineering projects such as tunnelling and slope stability. However, direct determination of these parameters is difficult and requires high-quality core samples for tests. Therefore, this study aimed to explore the applicability of the Brazilian test (BT) - a simple, less sophisticated and inexpensive method for both specimen preparation and testing - to estimate the UCS and shear strength parameters of rocks. Thirty-seven rock types were sampled and tested, 24of which were volcanic, 8 were metamorphic, and 5 were sedimentary. Statistical equations were derived to estimate the UCS and shear strength parameters of rocks using the BT. The validity of the statistically derived equations was confirmed using predictive analytics software (PASW Statistics 18). A strong linear relation was found between BT and UCS values. BT and UCS values exhibited prominent linear correlations withthe cohesion values of rocks. The Mohr envelope was also used to determine the cohesion and friction angle of rocks using BT and UCS values. It is deduced from the current study that the BT values can be used to estimate the UCS and cohesion. However, no relation was observed between the angle of internal friction values and the UCS and BT for all rock types. Therefore, different approaches are suggested for the estimation of the internal angle of friction for application in the preliminary design of projects.

Jan 1, 2015

By William G. Pariseau, Mark K. Larson, Heather E. Lawson

Rational design based on engineering fundamentals is essential for the layout of safe, stable shafts and tunnels. Shafts and tunnels including winzes, raises, adits, and crosscuts are lifelines to the underground and must be secure. The contribution of this paper describes a significant extension in existing software previously developed for five important design problems in strata-bound mines such as coal, trona, salt, potash, and some large, lead-zinc mines. This extension in software allows analysis to proceed in three easy steps: (1) preparation of a strata properties file, (2) generation of the finite element model, a mesh, and (3) finite element program execution. Circular, elliptical, and rectangular shaft sections are available for a single shaft, twin shafts, and shafts in a row. Spacing of twin shafts and shafts in a row is a free parameter (pillar width). Tunnel shapes are the same as shafts but include the conventional arched back section. Dipping strata of variable thickness, depth and orientation relative to the excavation of choice are allowed. The analyses are three-dimensional. An elastic-plastic material model based on associated rules of flow and an N-type yield condition for isotropic, transversely isotropic, or orthotropic rock are used for all strata. Example analyses from several hardrock mines are provided to illustrate the three-step process including mesh plotting and plotting of selected results. The goal of this software is to advance mine design technology for improved miner health and safety.

By VIVEK KASHYAP, PATRICK TAYLOR

The presence of iron in sphalerite induces the formation of zinc ferrite (ZF) during roasting. Zinc refinery residues (ZRR) and electric arc furnace dust (EAFD) contain a significant amount of zinc ferrite and are difficult to treat. According to the literature, up to 71% ZF has been found to be present in ZRR. The dissolution of zinc ferrite is inefficient even in aqua regia. The Waelz process is an existing process to recover zinc from electric arc furnace dust by reduction using carbon monoxide followed by the volatilization of zinc. In this study, zinc was selectively extracted from zinc ferrite by partial reduction of zinc ferrite at relatively low temperature followed by leaching in dilute sulfuric acid (20 g/L). Pure zinc ferrite samples were partially reduced to zinc oxide and magnetite by using H2 gas as a reductant. The presence of magnetite and zinc oxide was confirmed by X-ray diffraction (XRD) technique. A maximum of 95%zinc extraction was achieved after leaching with sulfuric acid on the reacted samples. The paper also discusses the effect of time, temperature, and concentration of H2 in the reducing gas on the extraction of zinc and iron from ZF.

Sep 16, 2020

By K. E. Waters, M. Mirnezami, R. Gauvin, A. Jordens, K. W. Malas

"There is currently very little information on the physico-chemical properties of rare earth elementbearing minerals, or on their processing. With the increasing demand for rare earths, this is something that needs to be addressed. This paper introduces some surface chemistry analysis of fergusonite (YNbO4), and the bubble-particle attachment. Zeta potential measurements indicate adsorption of sodium oleate and, to a lesser degree, potassium amyl xanthate onto the surface, and an increase in attachment to an air bubble is observed at pH 4.5 and 6.5. At a pH of 10.5, no attachment is observed, whether in the presence of the reagents or not. This analysis, although initial, will be used to initiate flotation tests, in order to facilitate the selective recovery of fergusonite. INTRODUCTIONRare earth elements (REE) are increasingly in demand, due to their prevalence in both renewable energy devices and high-end electronics. An article in the New Scientist highlighted the importance of a number of REE, many of which most people are be unlikely to have heard mentioned (Crow, 2011). From batteries (lanthanum and cerium) to magnets (dysprosium and neodymium) and lighting (yttrium), the REE are crucial to the advancement of technology and energy saving devices. For example, neodymium is finding most use in the high end magnets that keep the motors turning that power wind turbines and electric cars. In the case of yttrium, the demand outstripped the supply in 2010, emphasising the need to develop deposits containing this and other REE (Crow, 2011). The impact of our dependency on REE has become even more apparent with the reduction in exports by China, which currently controls 97 % of the world’s rare earth production (Pitts, 2011).With the increasing demand for rare earth elements (REE), there is a drive to exploit the known resources around the world. However, the physical beneficiation of the rare earth element bearing minerals is a subject which will require a great deal of investigation to fill the knowledge gaps surrounding these developing rare earth projects. There are numerous articles on REE mineralogy as well as the hydrometallurgical processing of REE concentrates (Alex, Suri, & Gupta, 1998; Peter Gromet & Silver, 1983; Ring et al., 1993; Schnetzler & Philpotts, 1970; Uda, 2000), however a common feature amongst these resources is the lack of detailed descriptions of the physical beneficiation processes required to concentrate REE-bearing minerals. There is work being conducted into reagents and methods for use in recovering some rare earths from their associated ores (Bulatovic, 2010; Ni, Parrent, Cao, & Liu, 2011), but much more in-depth research is required."

Jan 1, 2012

By Robert B. Fulton

The use of industrial minerals by the chemical industry as raw materials for manufacturing and in processing spans a wide assortment of minerals. This chapter aims to supplement rather than duplicate the commodity chapters. Its objective, to describe the uses of industrial minerals in the manufacture of chemicals, is attained by considering minerals used by the chemical industry in terms of the chemical element required and by giving particular emphasis to market factors. The mineral aspect, which is covered in the commodity chapters, is subordinated and attention is focused on the chemical and market aspects. Condensing this broad subject into a few pages permits treating only the most important elements derived from industrial minerals. The elements derived from petroleum, hydrogen and carbon, which quantitatively dominate as raw materials for the chemical industry, are omitted, as are the metallic elements and the minerals covered in other "use" chapters such as phosphorous, potash, and nitrogen for fertilizers and titanium dioxide for pigments. After eliminating on this basis, our definition leaves six elements of major importance: boron, bromine, chlorine, fluorine, sodium, and sulfur. These elements are treated individually under separate headings. Salt brines have particular importance as raw material sources for the chemical industry as shown in Table 1 "Salt Brine Derivatives" (Anon., 1967), which charts the chemical compounds derived from four types of brines: (1) Owens Lake type brines which are sources of boron and sodium compounds; (2) Midland type brines from which bromine, iodine, and chlorides of calcium, magnesium, potassium, and sodium are derived; (3) Searles Lake type yielding boron, bromine, lithium, magnesium, potassium, and sodium compounds; and (4) Silver Peak type produced mainly for lithium. Table 2 (Jones, 1973) affords an overview of the chief industrial minerals, the chemical products derived from them, and end uses of the products.

Jan 1, 1975

By Baker G

The exposures resulting from development work, following on the discovery of a new shoot of hIgh grade ore at the north end of the Sardine tin mine, during 1952, have provided an unusual opportunity to study the oxidation of a stannite-rich ore. Through the kindness of C. C. Morton, Chief Government Geologist of Queensland, an exactly located suite of specimens representative of the exposures was supplied by J. and W. Reddie. This was later supplemented by a number of specimens culled from a parcel ofrepresentative ore submitted to the Melbourne Ore Dressing Laboratory for testing.The Sardine tin mine, near Ewan, Queensland, has been the outstanding producer of the Kangaroo Hills Mineral Field. Since its discovery in 1918, up to 1952 it has yielded about 1,500 tons of cassiterite concentrates, and about 85 tons of stannite concentrates. The outcrop ore averaged 35% tin oxide, but the grade declined with increasing depth, and by 1930 had fallen to 7% tin oxide. In the northern section of the mine the ore shoots show a downward passage to complex primary s.ulphide ore, containing cassiterite and abundant stannite.The orebodies occur in a series of fissures in a crushed zone about 50 ft. wide in slates and quartzites that have been intruded by granite (Connah, 1952). A quartz porphyry dyke forms the footwall of the original main lode in its southern part, being traced' from the surface to' the No. 4 level (173 ft. vertical depth), and two narrow dolerite dykes were encountered in the workings north of the main...

Jan 1, 1954

By H. J. Brown

Pluess-Staufer (California) Inc. Lucerne Valley California operation is one of the largest producers of high brightness high purity fme grind limestone products in western North America. The San Bernardino Mountains area of southern California contains the largest high brightness, high purity limestone mining operations and undeveloped reserves in western North America (Fig. 1, Brown 1987). Combined annual production of high brightness limestone products from several operations is approximately 1.5 million tons, with an estimated gross value of $75 million dollars per year (Fig. 2). An additional 5.0 million tons of cement grade limestone is mined by several large cement producers in the nearby Mojave area (Brown, in press). The purpose of this paper is to summarize the geologic setting, genesis and mining of white, high purity crystalline limestone by Pluess-Staufer (California) Inc.

Jan 1, 1994

By Oliver Bowles

The various Latin American countries are undergoing a slow process of industrialization. The harvesting of one or two agricultural commodities or the mining of a few marketable minerals is being supplemented by development of an Integrated industrial economy. In many countries, progress in this direction has not been rapid, but as it gains impetus an increasing market for cement is a natural consequence. This is evident from the fact that industrialization is linked with increasing transportation, and means of transportation are very poor in much of Latin America. Bridges, culverts, and concrete Highway's, now scattered sparingly throughout the vast land areas south of the United States, must multiply as the demands of industry increase and as a higher scale of living is attained. Eventually the South American countries will be linked by modern highways. Furthermore, the arid climate of many regions creates a demand for construction of dams and irrigation works, and a continent poor in coal reserves but with abundant water power inevitably must direct its energies toward the construction of hydroelectric power plants. Countries rich in raw materials but with few natural harbors have urgent need of massive concrete breakwaters and docks. The demand for concrete in houses will also grow. Standards of living are low, and perishable building materials are widely used. As living conditions improve cement will be used increasingly in home construction. Even in the field of simple and modest housing cement affords a means of creating low-priced verminproof and fireproof homes, for which the need it imperative under climatic conditions that prevail in this area of the world. Already many of the countries have undertaken extensive public works, and such programs are likely to increase. Assuming moderate industrial progress and stabilized governments the demand for cement in this great southern area promises substantial growth.

Jan 1, 1940

By Marco Barla, Mariacristina Bonini, Giovanni Barla

ABSTRACT: The paper describes the characterisation studies of Tectonised Clay Shales at laboratory and in situ scale. The interest relates to tunnelling under squeezing and swelling conditions, in Italy, along the Apennines. The results of monitoring during full face excavation are presented in conjunction with numerical modelling. RESUME: Cet article présente la caractérisation, à l'échelle du laboratoire et in situ, des Argiles Chaotiques. L'attention est portée sur le creusement, dans ces milieux gonflants, des tunnels, dans les zones montagneuses des Appennini, en Italie. Enfin, on présentera les résultats de la modélisation numérique et la comparaison de ces derniers avec les mesures effectuées in situ. KURZFASSUNG: Die Arbeit beschreibt die Charakterisierungsstudien von tektonisierten Schiefertonen, sowohl im Labor als auch vor Ort. Das Interesse gilt dem Tunnelbau unter Quetsch- und Schwellbedingungen in Italien entlang der Apenninen. Die Überwachungsergebnisse des ganzflächigen Ausbruchs werden mit numerischen Modellen präsentiert.

Jan 1, 2003

To form a true picture of the early history of Queensland, we must think of white settlement advancing like an incoming tide, wave by wave; each wave lapping ahead a little further than the last. The credit for opening up the country belongs to a large number of pioneers, each of whom pushed out just a little further than his predecessors.Contrary to what one might expect, Rockhampton district was settled by overlanders from the south and not from the ocean side. When the Archers, the pioneers of the Rockhampton district, reached Gracemere in 1853, settlement had already made its way down the valley of the Dawson River; for it was from Leith Hay's station at Rannes (a few miles below Mount Morgan) that the Archers advanced northward into the unknown, to find the river that the explorer, Ludwig Leichhardt, had told them must enter the sea somewhere near the Tropic of Capricorn.The Archers travelled northward from Rannes up the valley of the Dee, coming out on the edge of the Razorback Range not very far from the point at which the Dawson Valley Highway drops over into Poison Creek. (Their diary records the bearings from a lookout point to various peaks around Rockhampton, and to-day, by plotting back from these peaks, we can determine the exact spot at which they descended on to the Fitzroy Flats.) We can be certain, then, that they must have been the first white men to set eyes on Mount Morgan; though to them it would have seemed to be nothing more than an insignificant hill...

Jan 1, 1939

By Carlos G. C

Geological mapping in various parts of Australia is revealing a number of regional associations of mineralizations with particular persistent stratigraphic horizons. Such associations have been found in the Broken Hill district of New South Wales, in the Nairne district of South Australia, in the Mount Isa district of Queensland, and in the Cloncurry district of Queensland. The question has arisen as to whether such mineralizations are of sedimentary origin, syngenetic with the enclosing formation, or whether they are of epigenetic origin, and reflect the selective hydrothermal mineralization of favourable beds on a regional scale.The purpose of this investigation is to test the use of sulphur-selenium ratios as an objective method of distinguishing between suphide deposits or sedimentary or supergene origin, and sulphide deposits of hydrothermal origin, with particular application to the districts mentioned. At the same time much data has been accumulated as to the selenium content of Australian sulphide ores. The possible use of sulphur-selenium ratios for this purpose was first demonstrated by Goldschmidt and his coworkers (1933; 1935), and later by Carstens (1941). Goldschmidt and Strock (1935) found that pyrite of sedimentary origin had a sulphur : selenium ratio of the order of 200,000 or more, whereas pyrite of hydrothermal origin had a sulphur: selenium ratio of 10,000 to 20,000. Carstensfound that sedimentary pyrite deposits in Norway contained less than 1 g. Se per ton, whereas hydrothermal pyrite deposits contained 20 to 30 g. per ton.

Jan 1, 1954

By George Mixter

MINING, in contrast to manufacturing, deals with a wasting asset. That which is taken out of the ground is gone, the property is depleted to that extent, and will eventually become exhausted of profitable ore. So the life of a mining company is dependent upon the ability of its management to develop improved methods to permit extraction at a profit of the lower-grade ores which remain, to extend by intelligent exploration the limits of its known ore bodies, and to find and acquire new properties to take the place of those that, for one reason or another, are no longer operated. Its history is a story of constant change, of the working out of properties here and the acquisition and development of properties there, to maintain the vitality of the whole. It is a story of estimating with the tools and the knowledge available the location and extent of hidden ore bodies and of devising the means of extracting

Jan 1, 1948