Search Documents

The growth of "Unit Load-cargo handling technology in world cargo lin- er trades over the last decade has cre- ated a situation in which special pur- pose-vessels (cellular container ships, roll-on/roll-off vehicle deck ships and Lash type vessels) are rapidly replac- ing conventional cargo ships, the principal means previously available for transporting heavy lifts. Consequently heavy lift traffic has tended to accumulate awaiting ship- ment, especially where discharge is required in "off beat" locations. A partial solution to this problem will be provided by new and small but exceptionally versatile ocean going heavy lift carriers now finding their way into world trade routes. These new ships combine extremely high lifting capacity, high manoeuvreability and exceptionally shallow draft with bow and stern Ro/Ro capability. They can handle rolling loads of exceptional size and weighing up to 1,000 tons Each. But the problem is a far larger and more serious but essentially a domestic one. Major industrial pro- jects in Australia will require pro- gressively heavier and larger plant and construction sites are becoming much more inaccessible. Whereas these new ocean going heavy lift carriers have ample capacity to satisfy part of the total transport requirement, there is clear evidence to show that domestic transport resources have little if any potential for increase in capability at the same rate as demand or at the same rate as sea transport facilities. Resolution of the larger problem is within reach but only through a pro- perly co-ordinated approach to future planning for the overall needs of large scale projects on a national basis. This co-ordinated approach must involve Federal and State government transport administrators, railway and highway authorities, shipping and road haulage interests and finally the planners of the projects which require these improved heavy haulage services.

Jan 1, 1973

By Vincent Canaguier

Methane is increasingly considered as a promising reductant for metal oxides, including chromite. To assess the possibilities of such reduction route, the gas-solid reactions between Ar–CH4–H2 gas mixtures and synthetic chromites are studied between 950 and 1050 °C. The influence of Mg and Al additions on the reduction-caburization of (Fe,Mg)(Cr,Al)2O4 solid solution is investigated thermodynamically, structurally and kinetically. The product phases are examined by x-ray diffraction (XRD), scanning electron microscopy (SEM), and electron probe microanalysis (EPMA). The reaction rate is derived from real-time exhaust gas measurements and post-reaction product analyses such as oxygen analysis. Kinetic models are proposed based on the product phase morphologies and confronted with the empirical data.

By R Dwyer, S Rea, W J. Bruckard, N McSweeney, R Holmes

"The innate ability of microorganisms to adapt to changing or inhospitable environments has often been exploited for industrial purposes and forms the basis of many current biotechnological processes. The ability of bacteria to adapt and adhere to specific mineral surfaces ensures that the energetic or nutritional requirements of the cell are met and often serves as a survival mechanism under unfavourable?growth conditions or conditions of stress. In this process, cells may rearrange or modify the macromolecules expressed on the cell surface itself or produce extracellular molecules, modifying mineral surfaces to render them more suitable for growth. The modifications that these molecules produce on mineral surfaces may result in changes to the surface charge and hydrophobicity of a mineral. As a result, these biomolecules may have some potential application as flotation collectors or modifiers.In this work, the effect of long-term exposure of Paenibacillus taiwanensis to goethite and common gangue minerals associated with Australian iron ores on the differential expression of membrane and extracellular proteins was determined. Both groups of proteins play a role in cell adherence to mineral particles. Cells were adapted to grow in the presence of each mineral over time. The proteins expressed on the cell membrane and the extracellular proteins excreted by the cell were isolated and analysed by two-dimensional polyacrylamide gel electrophoresis (2D gel PAGE). The outcomes of these studies are presented here and potential application of these products for flotation discussed.CITATION:Dwyer, R, Rea, S, McSweeney, N, Bruckard, W J and Holmes, R, 2013. Microbes and their metabolites - potential iron ore flotation reagents, in Proceedings Iron Ore 2013, pp 369-372 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

? Founded In 1953 ? Mining growth of 83% since 2007 ? We produced over 1 million ounces of Au in 2012 ? We Forecast of 20% Au production in 2013-2015 ? We have paid a dividend 31 years consecutively. Terry Reid ? 1992-93 Electrical Technical, College ? 1994-95 On the job placement College ? 1998 ? Licensed Millwright, ? 2005-12 ? Maintenance Reliability Planner ? 2012- Present Business Process Owner

Aug 1, 2013

By W. B. Boggs

Part 1 Originally, the copper produced at the Noranda ?smelter was shipped in the form of blister bars to the Laurel Hill refinery of the Nichols Copper Co., New York. In 1930 a refinery was built at Montreal East for the purpose of refining Noranda copper and copper from the Hudson Bay Mining and Smelting Co., at Flin Flon. After investigation of the probable costs of making anodes at Noranda and at Montreal, it was decided to make them at Noranda rather than to continue to make blister bars there. Fuel is a major item of expense in making anodes: and since less fuel would be required in making anodes from molten copper than in making them from blister bars, a lower anode furnace cost could be expected at Noranda than at Montreal. Further, the expense connected with making blister bars at Noranda would be eliminated. The cost of treating anode and wire bar furnace slags is a serious item in a refinery, and it was found that the cheapest method would be to ship such slags back to Noranda. With the anode furnace at Noranda, much less anode furnace slag would be made at the refinery. Against these savings which would be effected by making anodes at Noranda must be set the high operating cost of an anode furnace at Montreal, using only tank-room scrap and the Flin Flon copper. This furnace would be handling a comparatively small tonnage and would have a high cost per ton. The usual equipment for making anodes from. liquid copper consists of either a stationary reverberatory furnace or a tilting Tacoma-type furnace together with an anode wheel of the Clark or Walker type. The reverberatory type of furnace has been developed from the furnace used in the old Welsh process of smelting and refining copper, while the tilting furnace is a development of the holding furnace, which is essentially a Peirce Smith converter without tuyeres and provided with burners.

Jan 1, 1932

By B. Roy

The Somita plant processes low sulphide gold ore in Burkina Faso with a CIL process. After experiencing recurrent low gold recoveries, Somita undertook an investigation on the source of the problem. COREM conducted a mineralogical study on different pit samples. A series of tests was also conducted on a composite sample from the plant which shows a content of 3.4 g/t in gold and 0.48 % in graphite. A reference test in laboratory resulted in a recovery of gold of 75%, similar to plant recoveries for the evaluated ore. In these tests, even if cyanide is not deficient, it was diverted mainly into iron cyanide complex, copper cyanide complexes and by graphite adsorption. Causes of low recovery were also identified and quantified. Solutions to increase gold recovery were suggested such as increasing gold dissolution kinetics by O2 or by lead nitrate addition, change in activated carbon addition point location to the 1st cyanidation tank and finer grinding to increase liberation. Increase in the pH could also contribute to reduce cyanidation consumption. Following these recommendations, Somita changed carbon addition from tank 2 to tank 1 in the CIL circuit. This change led to an increase of more than 5% in gold recovery. A system for the addition of lead nitrate is also under implementation at the plant and benefit will be evaluated in 2013. Finally, pit management for cyanidation will be done based on mineralogy instead of gold content in the future.

Jan 1, 2014

By Mark F. Vancas

Virtually every new process plant project goes through the ?Feasibility Study? phase before actually being built. The Feasibility Study is used by the owners and the bankers to evaluate the economics of the project and determine whether or not the proposed investment meets their respective investment guidelines. With a positive result, the project is approved and goes to construction and operation. Then, the actual costs are incurred and these actual costs may or may not agree with what the Feasibility Study predicted. Just how good have Feasibility Studies been? This paper looks at various projects and compares predicted to actual results and also gives information on how to spot a poor feasibility study.

Jan 1, 2003

General recognition of the potential benefits of utilizing advanced technology has focussed public attention on the organisation of tertiary education. This has produced a situation where opportunities exist for significant changes to be implemented. The challenges to Mining education in this environment of change are analysed with respect to the setting of education objectives, the role of centres of education, course structures and student access to courses. The scope of the analysis includes formal courses for professional education and technical training, and programmes for continuing education and postgraduate research. Previous significant advances in mining technology illustrate the importance of encouraging the establishment of an extensive involvement with mining education. Education cannot be the sole responsibility of professional academic organizations; significant industry participation is essential. Methods of achieving this interaction are discussed. Major changes in techniques available for disseminating information provide a significant incentive to assess the relevance of existing course structures and restrictions on student access to courses. Establishment of a less rigidly progressive system of education is discussed with respect to the development of the full potential of computer based learning. This will expand the availability of mining education to include remote locations. The practical feasibility of such changes and recognition of the value of education as a commercial resource could also increase overseas involvement in Australian mining education. Benefits of such changes and problems that may develop if accreditation systems are not also changed to take account of new technology are outlined.

Jan 1, 1989

By C. H. Hopper

DIAMOND drills have played an important part in the development of mines for many years. Recently. they have also entered the production field arid the use of diamond drills m the primary breaking of ores has become a big branch of the industry. The writer has estimated roughly that the total diamond drilling in Canada during 1942 was 5,625,000 feet, of which 2,250,000 feet, or 40 per cent, was for blast-holes. This accounts for 6,750,000 tons of ore broken, using the conservative factor of 3 tons per foot of hole. Many consider that the use of diamond drills for blast-holes is the most important advance in mine practice of the past decade, and the industry owes a great deal to the staff of Noranda Mines, Limited, for the pioneering they have done in the development of long-hole mining methods and for publishing their results. A great many mines have followed Noranda's lead. At the Waite-Amulet, Aldermac, Flin Flon, Canadian Malartic, Hoyle, and Matachewan Consolidated mines, most of the ore is broken by long-hole blasting. While the mines were developing new methods, the diamond-drill industry was developing mechanically-set bits and better machines. Through the effective use o smaller, cheaper diamonds, as well as more efficient setting, bit costs per foot are only one-half what they were ten years ago. Few people realize that a diamond bit is relatively inexpensive. The common EXT coring bit, for example, contains some 200 small diamonds, weighing altogether about 2.70 carats which, at $3.40 per carat, cost $9.20. After use, the equivalent of about 100 of these diamonds may be recovered. Therefore the true cost of the bit is only $7.00, made up of $4.60, the cost of the diamonds lost, $2.00 for setting, and $0.40 tax. The trend in machines has been toward specialization for the different classes of rock in blast-hole work. Light, high-speed machines have been developed for soft ores and higher powered machines for hard ores.

Jan 1, 1943

By Chris D. Thompson

In Southern Ontario, Canada, piles are frequently driven through competent clayey soils to obtain end bearing on extremely dense till or bedrock. One reason for this is the difficulty at assessing the adhesion of the clayey soils. This is illustrated by texts, such as the Canadian Foundation Engineering Manual, which is the standard of practice in Canada, that indicate that theoretical analysis of the adhesion values of such soils are unreliable. In this paper, the results of high strain dynamic testing have been used to estimate the shaft resistance of 11 closed end pipe piles driven in overconsolidated very stiff to hard clayey tills at four sites by means of the CAPWAP wave equation analysis. More than twenty-five years of experience with bearing capacity predictions by such means have developed considerable confidence in its accuracy. The results were found to correlate reasonably with the average Standard Penetration Resistances of the clays at the sites. There was a linear relationship between an adhesion of 64 kPa at 20 blows per 300 mm and 192 kPa at 60 blows per 300 mm. At one site, 6 piles were tested and found to have a wide range of Standard Penetration Resistance and estimated adhesion in the same stratum. While there was significant scatter of the results, piles would have been safe at design loads obtained from the relationships established by the analysis carried out for this paper after applying appropriate factors of safety.

Jan 1, 2002

By John R. Zelonka

Models made by encasing strain-gage networks in epoxy are described and evaluated. With this technique relatively complex models can be constructed in which any number of gages can be located and alined precisely. Although the gages are an integral part of the model matrix, they create no important mechanical or thermal stresses. Model construction techniques and experimental data proved reproducible and reliable. In addition, the sGlution obtained with these models to the problem of the state of stress around a circular hole in a plate subject to a plane stress condition was in agreement with theoretical, photoelastic, and finite-element solutions.

Jan 1, 1970

By J. J. Gusek

Several final pits in the Seneca No. 1 Surface Coal Mine were abandoned in the 1960's without being reclaimed. In addition, a progressive landslide aggravated by the abandoned mine land conditions was threatening a county road and private property. An AML-funded project to stabilize the landslide and reclaim the final pits was completed in 1986 for the Colorado Division of Mines and Geology (formerly Colorado Mine Land Reclamation Division). The site was visited after ten growing seasons. The land is stable and the vegetation re-establishment is strong. Volunteer native plant species are now invading the reclaimed sites.

Jan 1, 1997

By K. H. J. Clarke

SINCE the beginning of this century the non-ferrous mineral industry has contributed $17,809,-000,000 to the economic growth of Canada. To contemplate the vast amount of investment capital required and the resultant beneficial distribution of these billions of dollars for labour, transportation, supplies, taxes and dividends, challenges the imagination. It is the purpose of this paper, (a) to trace the development of the industry since its formative period to the present; (b) to discuss the current situation and problems; and ( c) to attempt to peer into the hazy future. Although there are 21 metals currently being produced in Canada which are classified as non-ferrous, or as alloying metals, copper, lead, zinc, nickel-the metals which will be discussed in this paper-constitute almost 60 per cent of their total value. ;The story

Jan 1, 1961

By R. Ribacchi, P. Tommasi, C. Consorti, P. Campedel

The runout of dry blocky rock avalanches produced by planar rockslides affecting a limestone formation with clayey interbeds is analysed by means of distinct element modelling. Numerical analyses are validated by means of the back analysis of a historical rockslide occurred in the investigated area and physical aspects of the phenomenon evidenced by modelling are discussed. On analyse par la méthode aux élements distincts la distance de parcours des avalanches rocheuses sèches produites par des glissements plan interessant une formation de calcaire à intercalaires argilleux. Les analyses numeriques sont validées à l’aide de la back-analysis d’un glissement historique survenue dans le site en examen. On décrit les aspects physiques su phénomène mis en évidence par la modélisation efféctuée. In diesem Beitrag wird die Reichweite von Steinlawinen besthend aus trockenem blockhaftem Fels mittels der Distinct Element Methode untersucht. Die Steinlawinen werden erzeugt von Rutschungen in einer Kalkstein-Formation mit tonhaltige Schichten betreffen. Die numerischen Berechnungen wurden anhand einer Simulation einer historischen Bergsturzen verifiziert, der sich auf den untersuchten Gebiet ereignete. Auf der Basis der erhaltenen Ergebnisse wurden die physikalischen Aspekte der untersuchten Steinlawinen analysiert.

Jan 1, 2003

By Seth L. Pearlman

A major excavation support case history for the Eastern approach to the Third Harbor Tunnel (THT) in Boston, MA is described, which uses an anchored Soil Mixed Wall (SMW). Both general and project specific information is provided regarding the design and construction of SMW walls. In addition, conclusions are presented that discuss the suitability of this particular application and other possible variations.

Jan 1, 1993

By W. Breytenbach

Traditionally, dithiocarbonates (xanthates) have been the preferred collectors for the flotation of platinum-bearing sulphides. However, collector development has led to trithiocarbonates (TTC), which have proven to be very effective bulk sulphide collectors. The interest in TTC flotation behaviour is currently focused on the interaction of these collectors with other collectors, specifically the dithicarbonates. Batch-flotation research has shown synergism to exist among dithiocarbonate, dithiophosphate and trithiocarbonate collectors. Increased sulphide recoveries, both for the first-minute and final concentrate, were realized using mixtures of these collectors relative to the standard.

Jan 1, 2003

By G. B. Shea

In 192b, there wore 47 fatal accidents in the California petroleum industry, 14.6 per cent more than occurred in 1927 when 41 men lost their lives in the drilling, producing, manufacturing, and marketing divisions of the industry. This increase in the number of fatal accidents for 1928 has caused the first upward trend in the fatality curve of the California petroleum industry since 1923. In no other year during the 6-year period have the fatalities in any one year been greater than those for the preceding year. This fact should be given serious consideration and study by the petroleum industry, and an endeavor should be made to cause the number of fatalities again to decrease and conform to the previous gradual declining trend of the fatality curve. The following chart shows the trend of fatal accidents during the past six years:

Jan 1, 1929

By S. G. Malghan, J. P. Van Dillen

Introduction Some uranium minerals are paramagnetic and hence are amenable to concentration by high gradient magnetic separation (HGMS). This paper describes effects of the HGMS parameters-pulp velocity, field strength, matrix loading, and magnetic field gradient-on the product recovery and grade. Unsatisfactory separation of uranium minerals by HGMS is related to ore-specific properties, such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix, and interference of fine-sized slimes. Experimental techniques to identify and resolve some of these problems are outlined. HGMS of Uranium Ores The mechanism by which uranium minerals are attracted to a magnetic field is either due to its magnetic susceptibility or its association with other minerals that are magnetic. Data on magnetic susceptibility of uranium minerals are scarce. The only reported data are for uraninite at 2360 X 10-6 cm3/mole. Povarennykh (Andres, 1976) concluded that the magnetic properties of minerals depend on: • Structure of the outer electron shell in a mineral with electropositive atoms; • Valence of the atoms; • State of the chemical bonds; • Type of coordination; and • Proportion of magnetic atoms (Fe, Mn, Cr, and Ni) in the composition of the mineral. However, information on the magnetic susceptibilities of the constituent atoms of a mineral alone does not suffice for evaluating the mineral compound as a whole. Most often, uranium minerals can be beneficiated by HGMS if they are associated with other minerals that are magnetic. This appears to be a more predominant mechanism by which the uranium minerals are beneficiated. Experimental A Sala-HGMS (Malghan and Subramanian, 1981), model 10-15-20, separator was used in the experiments. The matrix material-ferromagnetic stainless steel in the form of expanded metal or steel wool-was packed into a 38-mm (1.5-in.) diameter by 360-mm (14-in.) long canister. The matrix material occupied only a 150-mm (6-in.) length. The experimental set-up and slurry flow direction are described elsewhere (lannicelli, 1976). The response of uranium ores in the HGMS was studied by feeding well-dispersed slurry at 10% solids and examining the influence of process variables on selectivity and overall uranium recovery. The chemical and mineralogical characteristics of the ores under study are presented in Table 1.

Jan 12, 1983

By Ajit Kumar Jaiswal

"Electric Arc Furnace (EAF) being a power-intensive equipment, EAF based industries are highly dependent on scarce electric energy. This is the reason Government of India is highly concerned about this and laid emphasis on the conservation of electric energy.This paper highlights factors contributing to reduction in specific electric energy consumption in EAF and suggests measures not only for power saving, but also for productivity improvement. To name a few, these are proper sealing of furnace, introduction of oxy-fuel burners, foamy slag practice, increased usage of hot metal/DRI, post-combustion of CO gas for preheating of scrap, improved selection & design criteria of electrics, power demand management, and process automation. Few cases also have been cited, where the above measures have helped in reaping significant benefits.IntroductionFor a long time, Government of India had focused on increase in energy supply, in particular, through electricity generation. Now the emphasis of Government of India has shifted from electricity generation to its conservation for following two reasons:??Power plants have become very cost-intensive??By saving energy, more of it can be delivered at lower cost to the consumersPower generating units, transmission & distribution agencies as well as consumers all have roles to play in the area of energy conservation. By energy conservation, we mean curtailing energy requirement by reducing energy wastages and taking up measures to improve energy efficiency of electric equipment/appliances. In almost all cases, this would be economically beneficial.India’s cost-effective energy conservation potential has been estimated by the Planning Commission at 23 per cent of total commercial energy generated ?1?. A national movement for energy conservation can significantly reduce the need for fresh investment in energy supply systems in coming years. It is imperative that we make all-out effort to realize this potential. Whether a household or a factory, a small shop or a large commercial building, a farmer or an office worker, every user can and must make this effort for his own benefit and for the nation’s benefit as well."

Jan 1, 2009

By Marise Keller Santos

Este trabalho apresenta os resultados parciais de uma tese de doutorado desenvolvida no PPGE3M da Universidade Federal do Rio Grande do Sul (UFRGS), com as Empresas Produtoras de Resíduos perigosos (EPRs) do setor metal mecânico da região de São Leopoldo/RS e suas Empresas Prestadoras de Serviços Ambientais (PSAs). A maioria das empresas PSAs iniciaram suas atividades com o apoio de grandes EPRs, principalmente, em função das suas necessidades de atender às exigências legais do órgão ambiental estadual, a Fundação Estadual de Proteção Ambiental (FEPAM), para a adequada disposição de resíduos perigosos. É importante salientar que não existe um diagnóstico sobre o setor de prestação de serviços ambientais no RS para resíduos industriais perigosos. Desta maneira, o objetivo deste trabalho foi o de identificar e priorizar as características da qualidade dos serviços ambientais de nove PSAs selecionados pelas próprias EPRs, durante o ano de 2013, por meio da adoção do Quality Function Deployment (QFD). O resultado piloto aponta a proatividade do setor nas características de empreendedorismo e inovação e no atendimento à legislação ambiental.

Aug 7, 2018