Search Documents

By Gerald Stolarczyk

The Radio Imaging Method (RIM) is based upon electromagnetic (EM) wave propagation in the coal seam waveguide. The radio geophysics theory underlying RIM was developed by Hill of the national Institute for Science and Technology (Hill, 1984). Recent advances in radio geophysics instrumentation have increased operating range in the coal seam waveguide to almost 3,000 feet. This paper describes RIM longwall panel reconnaissance scans and tomography results.

Jan 1, 2006

By W. K. A. Congreve

Introduction Less than a hundred years ago the engineer was able to do his job without concern for the science that underlay his practices or for the men who operated his machines. But toward the end of the last century science began to be applied to industry, and its success was such that the plant which clung to empiricism was unable to compete with the plant that followed science. Even more recently, the engineer has been forced to consider the men who operate his machines, for modern large-scale industry has given these men education, social security, and power. Hence the engineer can get good, steady labour to operate his machines only if he can offer inducements. Wages are in general outside the control of the engineer, but he is able to control working conditions. This essay is concerned with one factor of good working conditions: safety. The writer became interested in this problem during three months' summer employment as a student at the Sullivan concentrator of the Consolidated Mining and Smelting Company and was surprised at the distance his investigations led him from the field of pure engineering into the fields of psychology, education, and publicity. Nevertheless, because safety has to do with machines and with men who operate machines, and because it profoundly affects plant efficiency, it is the job of an engineer, not of a psychologist or teacher, nor of the salesman publicity expert who is often so unfortunately employed in personnel relations. The size and complexity of the subject has limited the scope of this essay to the consideration of only a few aspects of industrial safety. Considerable attention has been given to the underlying principles, but the mechanical side of accident prevention, the design of equipment, erection of guards, etc., and the very important problems of organization and administration, have not been given attention proportionate to their importance.

Jan 1, 1948

By A. Baldwin

Reports technical progress in designing four machines to be used in mining coal underground, applying innovative concepts at the design stage (instead of add-ons). A study phase was followed by design activity, including calculations supporting the designs. Scale models of three machines were built, and a full-scale mock-up of the conventional loader was used to measure human factors parameters.

Jan 1, 1976

By Guoqing Li, Hao Wang, Nailian Hu, Victor Tenorio, Jie Hou

This paper presents an algorithm for optimizing the scheduling of trackless equipment in underground mines. With the shortest working interval and maximum productivity as goals, a genetic algorithm (GA) is used to solve the problem, and obtain the optimal working sequence with the most suitable equipment configuration possible. The input for the proposed method is the number of units and capacity of trackless equipment, the production process, ore amount in stopes, and the distance between stopes. The algorithmis verified using four setups of 5 stopes with 5 cycles, 5 stopes with 15 cycles, 10 stopes with 10 cycles, and 10 stopes with 30 cycles. The solution time of the algorithmis no more than 20 min, which is acceptable for practical applications. The results show that the setup of 10 stopes with 30 cycles is closer to the actual production of the mines, and the optimization model can effectively improve the operation efficiency. In this scenario, the robustness of the optimization is tested by simulating equipment failure events. Under the condition of 8% failure rate, the operation time is extended over 3.21–14.56% than expected, which represents strong robustness. The algorithm can quickly provide a feasible and effective solution for the production scheduling decision of trackless equipment in underground mines.

Aug 12, 2020

By W. A. Wilkinson

In creating a surface mine design, a complicated series of events may be required to meet both mining and environmental objectives. Envisioning the mine at every step of the operation can greatly assist the engineer to identify design and operational problems that might otherwise go undetected until the field operations reach the problem. Providing operations a visual progression of the mine ensures that critical designs generated by the engineer are understood and effectively communicated to operations. Providing the plan as electronic data to the surveyors and/or on-board GPS systems can ensure successful implementation of the design. This paper discusses using computer technology to generate a virtual mine plan and strategies to consider when communicating a virtual mine plan through electronic and paper formats.

Jan 1, 2002

By Nuno Cruz

"The concrete overbreak estimation for bored piles provides the quantification of the shaft’s expansion beyond its theoretical volume. There are stability analysis methods that can be employed before and after concrete pour but as for the moment of decision, during pile cast, the most common method still consists in measuring the rising of the concrete level in order to compare its poured volume with the theoretical pile section volume. This is a determinant parameter to monitor, not only because it assesses the bored shaft stability but also because it represents a direct cost. When analyzing the estimation methods commonly applied on-site it becomes evident that these are often affected by human errors that lead to misleading results. The objective of this paper is to identify those errors and discuss a subject which is usually overlooked. As a general conclusion, it was ascertained that most errors derive from inaccurate volumetric data, working procedures and gauging equipment. By acknowledging these widespread practices deep foundations contractors will be in a better position to make informed decisions on how to correct and improve bored pile stability.GENERALBackgroundWhen executing bored piles, the estimation of its concrete overbreak allows a swift appraisal of the excavation stability during the drilling process. This is simply obtained from the proportion of the poured volume of concrete over the drilled shaft theoretical volume, as shown in equation [1].Where CO = concrete overbreak percentage, Vc = volume of poured concrete, Vr = pile’s theoretical volume. This calculation not only provides a general idea of the shaft’s expansion from its theoretical volume, but also the outline of the excavated column’s geometry. For the latter, the outline will be as accurate as the number of measurements taken for each partial known volume of poured concrete. This means that for each load placed inside the excavation there is a corresponding rising of the concrete level. The profile of the definite pile is then plotted (see Fig. 1) and allows inferring about how stable remained the shaft walls up to the moment of casting.The technological developments in this area have provided other methods for determining pile stability before and after pile cast, such as ultrasonic echo sensing, cross-hole sonic logging or thermal integrity profiling systems. Notwithstanding, concrete overbreak assessment remains as common practice and confers the advantage of providing stability information during the process of pile casting."

Jan 1, 2017

By R. Rumpold

The platinum group metals (PGMs) palladium, platinum, and rhodium represent the key materials for automotive exhaust gas treatment. Since there are currently no adequate alternatives, the importance of these metals for the automotive industry is steadily rising. The high value of PGMs in spent catalysts justifies their recycling. The state-of the-art technology is to melt the ceramic carrier and collect the precious fraction in a liquid metal bath. As the feed material has quite high melting points, huge amounts of energy are required for this process. Hydrometallurgical treatments of the spent catalysts offer the possibility to recycle the PGMs with less energy and time demands. Moreover, automotive catalysts contain further valuable materials to improve the exhaust gas treatment. These compounds, like cerium oxide, cannot be recovered in pyrometallurgical processes. This paper deals with a special process that uses hydrometallurgical principles to recycle the valuable metal fraction from spent automotive catalytic converters. Hydrochloric acid in combination with hydrogen peroxide is used as leaching agent. This combination selectively dissolves the PGMs and the cerium, which can be recovered in separate steps. As the leaching solution is regenerated and reused, wastewater generation is minimized. Furthermore, the process residues constitute potential byproducts.

Jan 1, 2012

As we look back through the Proceedings of our Institute, we find few papers dealing directly with education and recruitment. Apart from papers prepared in the earlier decades of this century, there was little written discussion on the subject until the 1950s, and mostly this was by the professionals, the professors and lecturers who staff the various mining schools of Australia and New Zealand.I use the term "mining school" in its fullest and widest meaning, to cover all aspects from ore to metal, and not in the narrow meaning that the word might imply. At the same time, in restricting the parameters of this address to "ore to metal" I recognize that I am excluding the very important fields of physical metallurgy and materials science; this I do because there is a limit to the quantum of any paper, and in fact these subjects are more closely allied to the use rather than the production of metals.However, the lack of education papers does not mean that education has been regarded lightly by The Institute. Sir Maurice Mawby in his presidential address in 1968, reminded us of the original objectives of The Institute, one 'of which was, "To promote the arts and sciences connected with the economical production of the useful minerals and metals ...". Our present Royal Charter is more specific when it says that one of the objects of The Institute is, ". . . to encourage the study of engineering with special reference to mining and metallurgy ...". If we recognize that in itself membership of our Institute is one means of continuing our education, it is true that education has been a concern of The Institute since it was first founded.Occasionally in recent years, an intrepid president has ventured to tell the academics what the industry needs, and he generally does this in a "no-question" situation! However it is encouraging that those entrusted with mineral education have always accepted this; they keep coming back for more and ask us to tell them what we want, and they will provide it.In 1948 a considerable dialogue on education was initiated when a standing committee was established by the Council of The Institute. In the period 1949 to 1951, three papers were prepared under the chair...

Jan 1, 1974

By André Brasil

Dado que las represas de relaves construidas por el método de aguas arriba presentan deficiencias relacionadas con los aspectos constructivos y de seguridad, es difícil evaluar la variabilidad real del depósito basándose apenas en los procesos de campo. En ese sentido, el presente texto desarrolla un modelo para describir y simular el mecanismo de formación de las represas de relaves considerando las variables externas (concentración y caudal de descarga) e internas, así como muestra soluciones analíticas y numéricas comparados a nivel laboratorio.

Sep 9, 2007

By Mike Broczkowski, Laura Dewhirst, Kieran Large, Angelo R. Fernando, Heather Daigneault, Jim Johnson, Randy Wiens

The radioactive isotope radium 226 is a contaminant of potential concern in effluent waters from metal mining operations in Canada. Acceptable release levels of radium 226 are governed by Metal and Diamond Mining Effluent Regulations. Since radium is invariably present as a companion element in uranium ore, monitoring and controlling of radium 226 is a must for uranium mining operations. Measurement of radium 226 is traditionally carried out through a radiochemical technique involving selective co-precipitation of radium with barium sulphate followed by alpha spectroscopy for quantification. As of 2010, Cameco has also been using an ICP-MS based radium analysis method developed in collaboration with a research team at Trent University, Peterborough, Ontario. This method, which is highly automated and requires significantly less sample handling, with improved turn-around-times, is being used by Cameco site laboratories at the McArthur River and Cigar Lake mines as well as the Port Hope Conversion Facility. This paper compares the benefits and drawbacks of this new method, compared to the traditional alpha counting procedure drawing from almost ten years of field experience.

Jan 1, 2020

By Gabriel Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

Jan 1, 2007

By Terry Owen

Not since 1917 has a foreign company developed a standalone, grass roots gold mine in Russia. With Russia's political changes of the late 1980s, development of mineral prospects once again beckons foreign investors. Cyprus Amax's interest in Russia began before the mid-1991 breakup of the former Soviet Union. In 1990, Cyprus Amax began searching for such an opportunity. Early this year, production will begin at the Kubaka gold project located in the Russian Far East, near the Arctic Circle. The Kubaka project is a 1.75-kt/d (1,930-stpd) open-pit operation that will produce more than 9.3 t/a (300,000 oz/year) of gold. Identifying Russian mining opportunities In late 1990, the first Cyprus Amax people travelled to Russia. The trip was to determine the potential for western firms to develop profitable mines. This encouraging visit suggested that Cyprus Amax focus on the Russian Far East with its mineral riches and its easier access to the United States. The company's initial efforts thus focused on working with the Soviet Union's Northeast Geologic Expedition, the then government agency for exploration and geology in Russia's Far East. After the breakup of the Soviet Union, Cyprus Amax continued working with the same people, but they now represented new independent, nongovernmental entities. For three years, Cyprus Amax investigated numerous deposits. This resulted in the identification of two properties of significant interest, one of which was Kubaka. Location Kubaka is located in the Northern Evensk District of the Magadan Oblast in the Russian Far East. This is an area east of Siberia. The project is situated in a mountainous area of the Kolyma Range, about 300 km (985 miles) south of the Arctic Circle. It is 285 km (180 miles) north of the fishing village of Evensk and 380 km (235 miles) northeast of the silver-mining town Omsukchan. The site is 950 km (590 miles) northeast of the regional capital city of Magadan. Magadan, the political and economic center of the Oblast, has a population of about 150,000 people. It is served by a year-round deep-water port (with icebreaker assist) and an international airport with service to Moscow and Anchorage, AK. Access to the Magadan region

Jan 1, 1997

By Chris Leach, Lucie Spencer

This case study describes the geotechnical aspects of the basement construction for a multi-storey, residential and hotel complex located in the newly developed Elizabeth Quay precinct in Perth, Western Australia. The development included a three-level basement for car parking covering the full site area which was constructed using the top-down construction sequence. Soil conditions generally comprised 2m of fill overlying medium to dense clayey sands that in turn were generally overlying a very stiff clay stratum at approximately 13m depth. Bedrock level was generally encountered at approximately 22m to 35m below ground level. The ground water table was at a depth of approximately 1m below the existing ground surface level. A site boundary basement wall was constructed using a diaphragm wall retention system. The majority of the vertical loads from the building were transferred to the Kings Park Formation (KPF) bedrock through the use of foundation piles constructed by the CFA method. The CFA piles were installed from existing ground level, resulting in approximately 9m sacrificial concrete length from pile platform level to basement 3 (B3) level. The permanent column loads are such that a single CFA pile was not structurally adequate. To allow a full CFA foundation system to be adopted, an innovative design and construction approach was developed for these heavily loaded columns. This paper discusses the site technical details and the design and construction aspects required to meet the challenges offered by this project.

Nov 1, 2022

By Rajni Patel, John McDonald, Steve Dubnewych, Michael McKenna

The Upper Reach segment of the Northeast Interceptor Sewer (NEIS) is a3.2-km-long tunnel excavated in interbedded marine sedimentary deposits with approximately 40 m of cover. The tunnel was initially classified by Cal/OSHA as “potentially gassy.” During excavation, high levels of hydrogen sulfide and methane were encountered, prompting Cal/OSHA to reclassify the tunnel as “gassy.” In addition, the tunnel excavation encountered an abandoned, 100-year-old water tunnel known as the “Narrows Gallery.” This existing tunnel was completely full of water and under 30 m of hydrostatic head. This paper will discuss the unanticipated difficulties and design solutions implemented to construct a gassy tunnel exposed to high volumes of water.

Jan 1, 2005

SME's Annual Membership Report - 1961 Membership Directory

Jan 7, 1961

By George Otis Smith

WHAT American can enter this Western empire without his imagination being stirred by the stories of its past-yes, and even more by visions of its future! Whether we travel by rail or by auto, our pathway has its traditions of exploration and its records of early settlement. The mountain passes and the routes used by today's commerce are lasting memorials of the pathfinders whose unconquerable purpose was to search out a way-Lewis and Clark, Bonneville, Pike, Long, FrBmont, their names still live in your rivers and lakes and peaks. It was the glory of these adventurers that they spied out the land so that others might follow that long pro- cession of pioneers who occupied the new country- fur traders, gold miners, cattlemen, and homesteaders. Each of these pioneers attacked the problem of transportation in his own way, and each sought by his own method to win the resources whose richness had been reported by the pen of the Government explorer or by the swift rumor of the unnamed and unfamed adventurer. Trails were worn deep by these home or fortune seekers as they passed through the mountain barriers in successive waves-and these were waves that did not ebb, for this was an army of occupation. Along these main pathways of the West, as one historian has pointed out, the figure of chief interest was the sad- faced woman sitting on the front of the covered wagon.

Jan 1, 1926

By C. Van Landingham, A. Bailey, R. A. Schoof

A residential metals abatement program has been underway in Butte for more than 20 years. More than 1,350 yard and attic cleanups were completed by the end of 2018; most triggered by lead. While the focus is on remediation of residential soil and house dust, the program also includes a blood lead monitoring program with identification and abatement of additional sources of exposure for children with elevated blood lead levels (BLLs). As specified in the remediation program, studies are being conducted every 5 years to assess BLL data collected from Butte children. The first two studies have evaluated over 6,000 BLLs from 2003 through 2017 and evaluated trends over this time period, by Butte neighborhood, and as compared to areas outside of Butte. These studies showed that rates of elevated BLLs (i.e., those above 5 µg/dL) in Butte children have declined dramatically since 2002 but have been declining much more slowly since 2011. Improved rates of confirmation testing are needed to verify the rates of elevated BLLs. While the RMAP likely has contributed to these declines in BLLs the magnitude of impact cannot be quantified.

Mar 2, 2022

By John J. Ginty

The objective of the work reported herein was to evaluate state-of-the-art repeaters used in wireless communications to determine their suitability for use in extending the range of portable and mobile communications in underground mine applications. The scope of the work included wireless repeaters in the frequency range from LF (500 kilohertz) up to the one giga-hertz range. These repeaters included not only single-channel repeaters, that is F1/F1 repeaters for short range simplex party line communications, but in addition, F1/F2 type repeaters currently commercially available in the HF, VHF and UHF bands.

Jan 1, 1975

By T. C. Alex, S Srikanth, Premchand

It has been suggested that reduction of the iron and manganese phases as far as FeO and MnO is preferred for the complete liberation and selective reduction of the copper, nickel and cobalt oxides in manganese nodules. The oxygen partial pressure/temperature regime suitable for this purpose has been delineated. Free-energy minimisation and thermogravimetric results indicate that the requisite conditions can be achieved if more than 10% of neutral oil is used at temperatures greater than 923 degrees C. Neutral oil content, temperature and roasting time have been optimised to maximise leaching recoveries of Cu, Ni and Co: up to 96% of Cu and Ni and up to 85% of Co can be recovered if 15% of neutral oil is used as a reductant at 973 K for 90 min

Jun 21, 1905

By Ronald E. Triplett, George K. Burke, Bernard H. Voor

To accommodate larger double-stack rail cars through a tunnel, the existing active tracks were to be lowered. The tunnel is an elliptical, horseshoe-shape with concrete base support, removal of which would jeopardize the tunnel integrity, particularly since the soils beneath part of the tunnel floor included soft, saturated silt overlying rock. Grouted bar anchors combined with a SuperJet soilcrete strut replaced the existing support in situ prior to floor lowering. Close cooperation and detailed timely engineering support provided a quality project. Project design and construction, ground improvement methods, and the performance of the work are described.

Jan 1, 2001