Search Documents

By Joseph Daly

An investigation into inaccurate scatter of pyrotechnic detonators led to the innovation of utilising existing (every day) equipment in a manner to accurately determine the true scatter of detonators. This can then be utilised to determine the accuracy of a particular batch of detonators.

Jan 1, 2014

By Lanre M. Oshinowo, André Bakker

"An understanding of the parameters that govern the just-suspended impeller speed, Njs, and the distribution of solids, is critical to the efficient operation of hydrometallurgical and other processes involving solid-liquid suspensions. In this paper, the distribution of solids in stirred tanks under a range of solids loadings (0.5 to 50 vol%) was predicted using CFD and validated against experimental data obtained from the literature. The multiphase flow is modeled using the Eulerian Granular Multiphase model. This paper will also review the established design parameter Njs in the context of scale-up and compare it to the quality of solids dispersion as a means of assessing correct scale-up in suspension tank design. The results of this study will describe a straightforward procedure to obtaining comprehensive information about reactor behavior with complex CFD models.The performance of hydrofoil impellers and a 45° pitched-blade turbine at suspending solids under different agitation speeds was studied. Both single and dual impeller operation have been evaluated. The settled solids fraction for speeds below N js, and the cloud height for impeller speeds above Njs were predicted. The CFD predictions are in good agreement with experimental literature data on velocity distribution and cloud height."

Jan 1, 2001

By M. N. Brodie, John Chapman

INTRODUCTION - DEFINITION & HISTORICAL PERSPECTIVE While this symposium is concerned with comminution which, by definition, relates to all stages of size reduction of an ore body to a form suitable for mineral separation, the electrical drive aspect of the grinding section will receive most attention in contrast to the crushing, screening and materials handling elements of the process. The reason for this is that today's large mills, thirty feet diameter and upwards, present mechanical and electrical problems which require a degree of sophistication in their solution not previously required. The ability to satisfy these demands, so far as electrical technology is concerned, largely results from the development of semi-conductor devices. These can now handle typical electrical distribution power levels within remarkably s m all volumes and with high efficiency when compared with the motor-generator sets, mercury arc rectifiers, rotating amplifiers, magnetic amplifiers and vacuum tubes which were commonly used to provide speed and torque controls as recently as the early nineteen-sixties. The hardware available to the electrical engineer has changed dramatically whereby even the simplest control system formerly using hard-wired relays is now superseded by the program m able logic controller with its computer-like memory containing the sequence of operation, in other words, the software. Reverting now to the mineral process itself, it is assumed that the ore body has been mined using explosives and is delivered to the concentrating plant in its 'run of mine' form. The problem becomes one of reducing the material to a size which will permit an acceptable recovery of the mineral with the most economical use of energy. The size of 'run of mine' material will range from about minus five feet for high tonnage open pit operations to minus two feet for the smaller underground mine. The final reduction in size may range from minus ten mesh to minus two hundred mesh (exceptionally as fine as minus six hundred mesh) depending upon the concentration method and dissemination of the mineral values within the ore. There is no single circuit that satisfies all applications, but the pattern of metallurgical equipment use shown in Table 1 appears discernable from current practice, in general terms.

Jan 1, 1982

By Jeff LeBlanc, George Gutierrez, Carl Pitzer

The Bay Park Conveyance Project was one of the largest microtunneling and rehab projects in the United States at the time of completion. The completed project conveys treated water from the South Shore Water Reclamation Facility located in Nassau County, New York, which currently discharges an average of 50 million gallons per day (MGD) of treated water into Reynolds Channel, to the Cedar Creek Water Pollution Control Plant (WPCP) ocean outfall pipe. The pipe carrying treated wastewater was installed approximately 20–60 feet below the surface. The treated wastewater is conveyed via microtunnel construction of a 2-mile long force main from the South Shore Water Reclamation Facility to an existing aqueduct under the Sunrise Highway, the rehabilitation of an 7.3-mile stretch of the aqueduct via sliplining, and construction via microtunnel of a 1.6-mile-long force main to connect the rehabilitated aqueduct to the existing Cedar Creek Water Pollution Control Plant (WPCP) outfall, which discharges and diffuses treated water three miles offshore in the Atlantic Ocean. This paper will review the Design-Build requirements, the chosen innovative solutions during planning for the micro tunneling portion of the project and review the microtunnel construction on the project.

Jun 23, 2024

By Dennis R. Dolinar, Christopher Mark, Gregory M. Molinda

Despite more than half a century of experience with roof bolting, no design method has received wide acceptance. To begin to improve this situation, National Institute for Occupational Safety and Health (NIOSH) conducted a statistical study of roof bolt performance at a number of mines throughout the U.S. Case histories were collected from 37 mines with a variety of roof bolt types and patterns in a wide range of geologic environments. Performance was measured in terms of the number of roof falls that occurred per10,000 ft of drivage. The study found that roof falls are rare when the roof is strong and the stress is low, even with light roof bolting patterns. The focus of this paper is on the more difficult conditions, where the roof is weaker and/or the stress is higher. Analysis of the results led to guidelines that can be used to make preliminary estimates of the required bolt length, capacity, and pattern. The guidelines are based on the depth of cover (which correlates with stress) and the roof quality (measured by the Coal Mine Roof Rating (CMRR), and the intersection span. Another contribution is a formula for estimating the horizontal stress level in the eastern U.S. coalfields as a function of the depth of cover. The design guidelines are currently being implemented into a computer program called Analysis of Roof Bolt Systems (ARBS).

By Malcolm Ross

Fibrous minerals are common in nature but asbestiform minerals are rare. The unique mineralogical characteristic common to all the asbestos minerals is their morphologic form (or habit of crystallization) as polyfilamentous fiber bundles. The individual fibrils within the bundles have a tendency to be very long with a narrow range of diameters and grow with their long fiber axis in parallel orientation to the bundle length. The asbestiform habit imparts to the asbestos minerals sufficient flexibility and tensile strength so that most can be woven into cloth. In the past application has focused on their ability to insulate against the transfer of heat. However, these minerals possess other properties which make them useful in many industrial applications. © 2007 Elsevier Inc. All rights reserved. Keywords: Asbestos; Asbestiform; Fibrous

Jan 1, 2007

By Ray Brainard

The Jollyville Transmission Main will be a 10.5-km- (6.5-mile)-long, 213-cm (84-in.) diameter rock tunnel. The tunnel will pass beneath the Balcones Canyonlands Preserve, which was established to protect two endangered bird species, six endangered cave invertebrates and a threatened salamander. To address the sensitive habitat that the transmission main is to pass through, the city of Austin developed an environmental commissioning (EC) process that brought together environmental engineers and scientists, the city?s project management team and the designer team to work collaboratively to meet the city?s goals of producing a cost-effective design while also protecting the environment. This paper describes the environmental commissioning process and the benefits it brought to the project and environment through some unique environmental mitigation measures to protect this sensitive area.

Jan 1, 2012

Experimental Validation of a Flotation Cell Model

Sep 13, 2010

By Ronald M. Hays

The Duluth Gabbro Complex in Northeastern Minnesota possibly contains a significant domestic copper resource and the nation's largest nickel resource. Exploration has discovered large low-grade copper-nickel (Cu-Ni) deposits between Hoyt Lakes and the Boundary Waters Canoe Area (BWCA). The mining and processing of Cu-Ni will have environmental, economic, and social impacts. The purpose of this study is to relate major environmental, economic, and social considerations to various aspects of Cu-Ni extraction. An open pit and two underground (block caving and open stoping with backfilling) models were developed to generate information on the impact of Cu-Ni extraction. Important considerations having environmental, economic, and social impacts (luring various aspects of Cu-Ni extraction are identified and defined. These aspects are exploration, development, mining, beneficiating, smelting, transportation, and termination of operations. Considerations are grouped into the general categories of site, industrial, energy, climatic, resource, water, air emission, waste disposal, employee, tax and royalty, transportation, and community considerations. Cu-Ni extraction in Northeastern Minnesota presents major environmental, economic, and social risks. Decisions are required on trade-offs between adverse and beneficial impacts. The approach used in this study assists in assessing environmental, economic, and social impacts. It will aid in the examination of potential and projected short-term and long-term advantages and disadvantages and will aid in the development of Minnesota's Cu-Ni resource for the maximum benefit to society.

Jan 1, 1974

The nature of the specialty glass and ceramic business magnifies the dependency of the ultimate product on the unique properties of their raw materials used to make them. This dependency has implications in the management of risk in the supply process which requires a special procurement organization and program commitment to be successful. The Coming system of managing critical materials and factors in development of alternate new suppliers and products is discussed.

Jan 1, 1989

By B. Simser, T. Butler

Glencore’s Nickel Rim South Mine, located in Sudbury, Ontario, Canada, is a primary/secondary blasthole operation with ore zones lying between 1,100 and 1,700 m below surface. One of the main benefits of the primary/secondary mining method in high stress ground is that up to 50% of the mining will take place in secondary stopes that should be in a yielded rock mass state. Every future secondary mining stope begins as a primary stope abutment pillar. As with many mines, the stress loading history and rock mass conditions can vary considerably in space and time. Safe mining practices cannot allow for an assumption that the planned secondary stopes are indeed yielded. An incorrect assumption can result in mining development and stoping taking place in high stress ground rather than the expected yielded rock mass conditions. This can result in higher levels of seismicity than expected and incorrect ground support recommendations in areas where workers could be exposed. Seismic monitoring is the mines’ premier tool to track the actual rock mass response to mining. Yielded zones have a reasonably clear seismic signature/pattern over time that is visible in the collected data. The ability to accurately locate small magnitude seismic events can help define and delineate different stages of rock mass failure. The vast majority of the seismic data recorded by the microseismic monitoring system is below moment magnitude (Mw) 0.0. Examples are provided showing how small seismic events (Mw < -1.5) can help provide feedback from the rock mass deformation that allows the ground control engineer to gain a better understanding of how the rock mass is responding to mining processes.

Apr 26, 2022

By Maria Salazar-Villalpando, Todd H. Gardner

"Efficient utilization of CO2 can help to decrease global warming. Methane reforming using carbon dioxide has been of interest for many years, but recently that interest has experienced a rapid increase for both environmental and commercial reasons. The use of CO2 provides a source of clean oxygen, which eliminates the need for costly oxygen separation plants. The product of dry reforming is useful syn-gas, which can be used to generate electrical power in a SOFC or in the production of synthetic fuels (hydrocarbons and alcohols). Hexaaluminate catalysts prepared at NETL may represent a product that can be utilized for the conversion of CO2 to syn-gas. In this work, transition metals dispersed in barium hexaaluminate have shown to be promising new catalysts for dry methane reforming. In this investigation, a series of BaNixAl12-yO19-d catalysts with varying Ni content were prepared by co-precipitation followed by calcination at 1400°C. CO2 reduction by dry methane reforming was carried out to determine catalyst performance as a function of temperature and carbon formation was also quantified after the reforming tests. Results of catalysts characterization, dispersion and surface area, were correlated to catalytic performance.IntroductionEfficient utilization of CO2 can help to decrease global warming. Methane reforming using carbon dioxide has been of interest for many years, but recently that interest has experienced a rapid increase for both environmental and commercial reasons. The use of CO2 provides a source of clean oxygen, which eliminates the need for costly oxygen separation plants. The product of dry reforming is useful syn-gas, which can be used to generate electrical power in a SOFC or in the production of synthetic fuels (hydrocarbons and alcohols). The dry reforming reaction has been known for a long time. Recent publications have reported studies over several catalysts. For example, the CO2 reforming of CH4 over mesoporous nanocrystalline zirconium powders (ZrO2–3%M2Ox; M: Ce, La and K) at 700ºC have shown methane conversion up to 60% (1). Similarly, the effect of Ni content (1–12 wt%) on the surface and catalytic behavior of bimetallic PtNi catalysts supported on ZSM-5 for reforming of methane with CO2 has been studied and report shows a maximum conversion of 16% and catalyst deactivation was observed during the first hour of time on stream (2). In another report, (3) Ni/a-Al2O3 catalyst was tested for syn-gas generation at 750ºC. The maximum methane conversion was 25%."

Jan 1, 2008

By J. Weyer

"Threshold limit values (TLVs) for NO and NO2 have been reduced drastically in 2016. Emissions of diesel engines have been reduced in the last decades. In many cases this is not enough to stay under required TLVs. Remaining gas in the blasted rock is set free during loading and transport. At the end, only a combination of measures with a further reduction of diesel motor emission, replacement of diesel driven vehicles by electric equipment, new explosives with reduced NO and NO2 production, changes in the organization and effective ventilation measures can ensure that the TLVs are not exceeded. KEYWORDS Blasting fumes, Gas measurement, Gases, Threshold Limit Value (TLV) SHORT HISTORY OF EXTRACTION OF RAW MATERIALS The extraction of raw materials—besides haulage and transport—is one of the main processes in mining and tunneling. The principal objective is the creation of a material which can be transported from the place of extraction (face) to another place for further processing or direct use. Furthermore, recently a desired grain size distribution has become more important. A revolutionary development took place in the course of centuries. With the use of primitive tools like shovels, chisel and iron in the 12th/13th century in Freiberg, ore mines performances of 12 16 cm per man and week could be reached in cross section of 1 m2. Recalculated with an assumed average density, this is a performance of 0.006 t/h. With the introduction of black powder into the subsurface in 1627 by Caspar Weindl in the city of Schemnitz (nowadays Banska Stiavniza), performances increased. A part of the hard extraction work was now done by the explosives. But first in 1767, it was recognized in a mine in Freiberg that more than 1 hole could be drilled (hand-drilling) and blasted. This discovery was so important that a plate with an inscription describes this event. The performance was increased more than 10 times compared to the extraction with chisel and iron. Since this time, drilling and blasting has been the most important innovation force for the increase of the performance. Problems with noxious blasting fumes led to the construction of the first tunneling machine by Henry Joseph Mouse in 1846 (beside shield machines from 1825) (Stack, 1982)). The triumph of mining machines started only interrupted by the two world wars. The development of hard rock boring machines (including roadheaders) was enforced after 1945. An almost complete extraction by hard rock boring machines was predicted for the turn of the millennium. And, indeed, one could find powerful machines in Canadian potash mines which were able to mine 1000 t of potash in 1 hour. That was an increase in the performance by several powers of ten. But already in the 1980s, it was recognized that the ambiguous goal could not be reached. Problems with wear of the tools, radius of curves, minimal length of openings, size and costs of the machines led to a more or less parity between drilling and blasting on one side and machines on the other side, of course depending on the field of use. For this reason, drilling and blasting is still the dominant extraction technology for raw materials. In the development of drilling and blasting technologies, the focus was mainly on the improvement of the safety but also on the increase of the blasting power and performance. Examples are tests for the increase of the power of ANFO explosives which were carried out in the 1970s and 1980s, in the former teaching mine “Reiche Zeche”. In the 1980s vehicles for loading and mixing of ANFO explosives have been developed, the blasting cab sensitivity of ANFO has been increased, emulsion explosives have been developed and up to now further developments like PMMA LOX EX explosives are on the way. At the turn of the millennium, 6 million t/a explosives have been used worldwide. Annual rates of increase of 2% have been predicted (Weyer, 1999). Meanwhile the focus changed from an increase of the performance"

Jan 1, 2019

By A. B. Cecala

Video technology coupled with data logging exposure monitors have been used to evaluate worker exposure to different types of contaminants. However, previous application of this technology used a stationary video camera to record the worker?s activity while the worker wore some type of contaminant monitor. These techniques are not applicable to mobile workers in the mining industry because of their need to move around the operation while performing their duties and tasks. The Helmet-CAM is a recently developed exposure assessment tool that integrates a person-wearable video recorder with a data logging dust monitor that are worn by a miner in a backpack, safety belt, or safety vest to identify areas or job tasks of elevated exposure. After a miner performs his or her job while wearing the unit, the video and dust exposure data files are downloaded to a computer and then merged together through a NIOSH-developed computer software program called EVADE (Enhanced Video Analysis of Dust Exposure). By providing synchronized playback of the merged video footage and dust exposure data, the EVADE software allows for the assessment and identification of key work areas and processes, as well as work tasks that significantly impact a worker?s personal respirable dust exposure. The Helmet-CAM technology has been tested at a number of metal/nonmetal mining operations and has proven to be a very valuable assessment tool. Mining companies wishing to use this technique can purchase a commercially available video camera and an instantaneous dust monitor to obtain the necessary data, and the NIOSH-developed EVADE software will be available for download at no cost on the NIOSH website.

Feb 27, 2013

By N. T. Lowe

This Bureau of Mines publication presents salient deposit information in abstract form on 119 principal mineral deposits in the State of Nevada. Commodity coverage addresses 17 critical and strategic commodities that appear to have commercial production potential in the State. The core of the deposits described is taken from those properties evaluated d under the Bureau of Mines Minerals Availability Program (MAP); additional deposits are included to provide a more complete coverage. Institutional and infrastructural factors affecting mineral development are also discussed.

Jan 1, 1985

By E. P. Olberg, A. Yu. Chikin, S. V. Petrov, M. P. Belykh, N. L. Belkova

"Bacteria that grow in autochtonous communities of gold heap leaching (HL) wastes are adapted to high concentrations of contaminants and environmental conditions. An example of a mine in the Sakha (Yakutia) Republic showed that the bacterial factor had a significant influence on cyanide breakdown and copper and nickel removal in the conditions of HL ore pile zoning compared to chemical oxidation. The diversity of bacterial communities growing in natural and simulated conditions of a HL ore pile was determined for the purpose of the study. The identified bacterial communities included genus Achromobacter and Serratia, which were found to be adapted to a wide range of temperature and can be considered as potential microorganisms for detoxification of gold HL wastes. INTRODUCTION Technologies and systems of passive treatment are of a special interest in relation to solving environmental problems of gold HL wastes detoxification, when neutralization time is not considered as a limitation (Alvarez et al. 2005). Passive treatment methods are based on reagentless spontaneous breakdown of cyanide caused by natural factors, including activity of autochthonous bacterial communities. Implementation of a reagentless biodetoxification technology for mature HL operations provides reduction of environmental impact on industrial site locations and substantial economic benefits compared to conventional chemical processes of neutralization that prevail in the Russian Federation territory. Passive treatment of cyanide-containing wastes was investigated by M. Botz, T. Mudder, S.V. Petrov, L. Simovic, A. Smith, C.A. Young etc. However, the bacterial factor (autochtonous bacterial communities) role in this process is practically unexplored. Thus, the aims of the study included the investigation of a bacterial factor influence on passive treatment of gold HL wastes and the identification of functional groups of bacteria involved in passive treatment."

Jan 1, 2018

By J. R. Schafler, J. L. Brinkman

"Since the year 2000, 59 miners have lost their lives to explosions occurring in underground coal mines in the US. More accurately, those explosions were methane ignitions that propagated through the mines due to coal dust involvement; despite current explosion prevention standards. There are 4 basic strategies employed to manage the risk of coal dust explosions in many other coal mining countries around the world: removal of the coal dust, wetting of the coal dust to prevent it from becoming airborne, mixing of the coal dust with stone dust to increase the total incombustible content, and explosion activated barriers which make the entire roadway inert. However, American standards only mandate the first 3 of these 4 methods. It is possible that US coal mine safety measures could benefit from the implementation of the 4th method, the use of explosion barriers. This paper will discuss differences/similarities in barrier regulations used in other countries, as well as some potential difficulties with adapting a stone dust bag barrier system to US underground coal mines. Also, details and feedback gathered from two operating mine site trial barrier installations will be shared.INTRODUCTION Since the year 2000, 59 miners have lost their lives to explosions occurring in underground coal mines in the United States (US); 29 miners were killed at the Upper Big Branch mine in 2010, 5 at the Darby Mine No. 1 in 2006, 12 at the Sago Mine also in 2006, and 13 at the Jim Walter No. 5 Mine in 2001.[14] To be more accurate, the explosions that killed those miners were methane ignitions that propagated through the mines due to coal dust involvement.[18, 19, 20, 21] These deaths occurred despite current explosion prevention strategies, standards, and regulatory oversight. This poses the question, can more be done in the US to prevent coal dust explosions and their widespread damage. In review of current practices and regulations from several large coal mining countries, a disparity in prevention strategies arose. The main difference between the US and other countries was that the US does not encourage, mandate, or regulate the use of explosion barrier systems as an additional coal dust explosion mitigation measure. This raised many questions. First and foremost was whether or not the US coal mining industry and its miners could benefit, in terms of safety and fatality prevention, from the implementation of the explosion barrier systems that are used in other countries. Furthermore, are there significant differences between the coal mines in countries where explosion barriers are used and US coal mines, which would preclude the system from being adapted and implemented in the US? Also, what are the similarities and differences in explosion barrier systems, use, and regulations between other countries that use them?"

Jan 1, 2017

By Walter Ensinger

Special foundation works is one of the most innovative sectors in civil engineering and construction. Both engineering techniques and construction machinery are undergoing continu­ous further development. These developments are providing ways to meeting the world-wide requirement for special geotechnical works even faster, even better and more efficiently. Unfortunately, accident prevention organisations have had to realise that the figures on in­dustrial accidents in special foundation works are still above average in number. The Safety & Environmental Working Group of the EFFC thereupon started to carry out a survey on acci­dents occurring in this sector and used this information as a basis for the preparation of acci­dent statistics and an accident analysis. The objective of this undertaking is to determine key accident occurrences and their causes and to consequently determine measures for improved health and industrial safety.

Jan 1, 2002

By G. M. Molinda

Ground Penetrating Radar (GPR) is being investigated for the potential to determine roof hazards in underground mines. GPR surveys were conducted at four field sites with accompanying ground truth in order to determine the value of GPR for roof hazard detection. The resolution of the current system allows detection of gross roof fractures (>63 cm (s1/4 in) zone) or rider beds in coal measure roof. Data quality is not yet sufficient to detect small bed separations or subtle lithologic changes in the roof. Differences in data quality are discussed, as well as suggestions for collecting improved data.

Jan 1, 1996

By Andre Zingano

The variation in pillar behavior at underground coal mines working in the Bonito coal seam is observed in both research and mining company case studies. There is no consistency in pillar behavior, as it varies from mine to mine. In some cases, it is possible to find rib yields for both excavation modes and pillar sizes. This paper?s objective is to investigate pillar behavior for different load conditions and pillar sizes. Three-dimensional numerical simulation models considering these factors were built. A matrix was then assembled to compare pillar behavior between loading conditions, as well as between different pillar sizes with the same loading condition. The results showed some pillar rib plasticity due to vertical loading and stress relief independent of the pillar size and load. For the same load conditions, the yielding thickness is the same for different pillar sizes.

Jan 1, 2012