Search Documents

By S Harvey

An inrush of water or mud into an underground mine, or sudden subsidence above mining voids represent low probability but high impact risks in underground mining. About two such incidents involving multiple fatalities or loss of production are reported each year worldwide. On average, Australia experiences one such incident every three to four years. This paper reports the development of a Standard that is intended to eliminate fatalities due to inrushes and subsidence.

Jan 1, 1998

Precast prestressed concrete piles designed to be end-bearing in a sand stratum at Drax Power Station met with extremely variable resistance during driving. Some piles came to virtual refusal almost immediately on entering the sand whereas others were driven to considerable penetration with very low resistance. Redriving and load tests on piles experiencing low resistance on initial drive showed that take up in strength occurred over a relatively short period of time. Investigations involving the use of pneumatic piezometers revealed the development of significant excess pore pressures during driving. Samples from boreholes showed that piles met the least resistance when the sand had a high silt content. Comparison with the original site investigation data demonstrated the difficulties in predicting detailed pile behaviour. The varied behaviour could not be related to the original borehole logs or to SPT or static cone penetrometer results. The factors controlling pile driving behaviour were essentially geological and could only be explained with reference to local soil grading.

Jan 1, 1989

By Geoffrey G. Huggins

Discussions are presented of the three phases of the noise reduction program on flight-type coal conveyors. The three phases are identification of noise sources, evaluation of potential noise reduction concepts, and implementation of noise reduction which is intended to reduce conveyor noise to less than 90 dB(A) in the underground mining environment. The major noise sources are impacts of the chain on the tail roller and on the top and bottom decks. A total noise reduction of 11 dB(A) was achieved by using techniques which are applicable to retrofit. These are a vibration isolated tail roller and an isolated wear strip on the return deck. A theoretical model of isolation provided by the isolated tail roller is developed. Appendices are presented which contain information on other potential concepts and additional data generated.

Jan 1, 1976

By William H. King

The Mining Division of the Bureau of Mines has been making development and power-requirement studios for the Interior Department Missouri Basin Field. Committee. The studies by the Bureau of Mines have as their purpose, the summarizing of potential future power requirements in the mineral industry within the Missouri Basin, special emphasis being placed on possible expansion of these requirements through construction of new mining enterprises by private capital. In preparing a proposal for the production of phosphoric acid from phosphate rock near Lander, Wyo., it was found that the basic information on the physical and chemical characteristics of the phosphate beds to determine costs of mining and treatment was lacking.

Jan 1, 1949

By R. N. Chakravorty, K. K. Feng

"There is growing evidence that modern methods of mining coal increase the risk of spontaneous combustion. Seemingly unimportant at this time, this hazard could prove to be a barrier to growth and development of the coal industry in some areas of Canada. The paper presents bedrock knowledge on spontaneous combustion gathered by scanning and evaluating current technical and research literature. Special efforts have been made to identify significant coal and environmental factors and to establish criteria for susceptibility. In addition to the state-of-the-art knowledge, preliminary results from on-going studies are discussed."

Jan 1, 1973

By Jorge Acosta

Desde la segunda mitad del siglo XX, el Perú es uno de los principales productores de cobre a nivel mundial. Por ello, su producción aumentó -en tanto se explotaron los pórfidos de cobre de Cuajone y Cerro Verde en la década de 1970, los skarns de Tintaya en la década de 1980 y Antamina en 2001. En sentido, el presente texto señala la producción minera actual a través de estadísticas desde 1950 hasta 2012.

Dec 1, 2013

THE Taranaki oil-field is situated on the western side of the North Island of New Zealand, at about its widest part, and may be said to be the most compact and fertile part of the Dominion, for, with the exception of the upper half of Mount Egmont and of the ranges adjoining, which absorb 36,000 acres, the whole of the area, minus what is taken up by the rivers and streams is suitable for settlement, and certainly two-thirds is good land. The gross area of the district is 2,417,299 acres. The principle rivers are the Wanganui, Mokau, Waitara, Patea and Waiwakaiho. Mount Egmont, which is 8260 ft. high, used to be called Taranaki, and from it the district takes its name (the Maori meaning of which is "sloping peak ").THE OIL-FIELDThe discription of an oil-field now-a-days usually resolves itself into a mass of figures and statistics, of great interest and value to the engineer and commercial man, but practically indigestible to the general public. It is the realm of the financierand the captain of industry.

Jan 1, 1912

By I. Soto, E. Córdova, A. Anani

The new caving megaprojects that are planned to go into production in the next decade have scheduled horizontal developments at very high rates, which are difficult to achieve. Research has been conducted that seeks to model the construction times for underground developments to determine the feasibility of achieving the planned rates. However, these previous attempts do not consider all the operational aspects that make up the mine development cycle. Here, we present a discrete event simulation (DES) model that individualizes each unit operation of the development cycle to determine the construction rates that new projects will be able to attain. The developed model was applied to the New Mine Level (NML) of the El Teniente Division (DET). The results indicate that it would be impractical to achieve the advance rates scheduled in the original plans if the unit operations of the mine continue to be executed using the status quo. The metres developed after six years in the sections analysed can be significantly improved by changing the maintenance strategy for the equipment (457 metres increase), orepass availability (194 metres increase), and the initial planning sequence (1 598 metres increase). It is recommended that the mine implements a flexible maintenance strategy, defines a strategy to ensure and increase orepass availability to contractors, and makes use of current simulation tools for a more robust development sequence planning.

Oct 1, 2022

By S. Möllerherm, E. Drüppel

"The development of indicators to assess the sustainability of mineral raw materials operations is amajor task with respect to its actuality and difficulty. This holds true even more when dealing withenvironmental indicators.The use of existing environmental indicators in the mineral raw materials industry leads to false orat least distorted results. Therefore the Institute of Mining Engineering I from the RWTH AachenUniversity developed indicators and an assessment system for the mineral raw materials industryon operation, company and sector level on behalf of the Federal Ministry of Economics and Labour(Bundesministerium für Wirtschaft und Arbeit, BMWA) and the Federal Institute for Geosciencesand Natural Resources (Bundesanstalt für Geowissenschaften und Rohstoffe, BGR).In total 30 indicators were defined and designed to assess the performance of the mineral rawmaterials industry in terms of sustainable development, 10 indicators for each pillar (economical,ecological and social pillar).The following paper describes some of the results focussing on the development of environmentalindicators. These had to be adapted or completely new designed in order to match the specificcharacteristics of the mineral raw materials industry."

Jan 1, 2005

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jason Navoyski, Jennica L. Bellanca, William J. Helfrich

Recent advances in computing, rendering, and display technologies have generated increased accessibility for virtual reality (VR). VR allows the creation of dynamic, high-fidelity environments to simulate dangerous situations, test conditions, and visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, the National Institute for Occupational Safety and Health researchers developed a VR framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization, and training. This paper describes the features of VR Mine using self-escape and proximity detection as case studies. Features include mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models.

By I. A. Costa, Y. Fouquet, F. Barriga

"Lucky Strike and Menez Gwen are two hydrothermally active sites located along the border of the Azorean plateau, southwest of the Azores islands where the alteration processes affecting basaltic rocks are prominent (Costa et al., 2003). Here we report on a slabby brecciated rock, abundant at both Lucky Strike and Menez Gwen, composed mainly of basaltic fragments cemented by hydrothermal precipitates from warm fluid circulation system. Research reveals that hydrothermal alteration takes place mainly by replacement processes, in which silicification is dominant (Costa et al., 1997 and Costa, 2014).Petrographic observations, including scanning electron microscopy (SEM), microprobe analysis, and mass balance studies made on basaltic fragments within the breccia show that silicification is one of the main processes resulting from hydrothermal fluid circulation. This alteration process leads to complete replacement by silica, in extreme cases, forming an impermeable cap that may contribute to the formation of sub-seafloor sulphide deposits, including examples in the geological past."

Sep 1, 2014

By José Luis Vitteri

Dado que se generan largas colas de los camiones mineros en los puntos de carga, es necesario revisar las causas principales que la originan. Entre estas tenemos: el desconocimiento de la variabilidad y sus efectos nocivos y la aceptación de que el mínimo costo de operación se obtiene con la mayor utilización de la excavadora. En este sentido, el presente texto describe el manejo de la variabilidad en los procesos de carguío y transporte con equipos pesados a través del estudio de sus causas, de forma que la única manera correcta de reducir el perjuicio de la variabilidad en el transporte, es manipulando la frecuencia inicial de los camiones.

Oct 1, 2013

By Zhongning Shi, Ramana G. Reddy

"By cyclic voltammetry and potentiostat electrodeposition using Potentiostat/Galvanstat, electrochemical behavior on Ag electrode in electrolyte 0.2M NaOH+0.01MPb(NO3)2-0.01M TeO2 -0.01M TlNO3 solution were also carried out at 298K. The processes of electrodeposition of Tl2Te3 and PbTl4Te3, a thermoelectric material, are reported along with analysis of the composition of the obtained deposits. The results showed that two different underlying processes are occurring depending on deposition potential. One process involves the reduction of TeO3 2- and Tl+ to Tl2Te3 in a potential interval of -0.70V < E < - 0.89V (vs. Hg/HgO). A second process at more negative reduction potentials involves reduction of TeO3 2-, Pb2+ and Tl+ to PbTl4Te3 in a potential interval of -1.02V < E < - 1.19V. The crystalline Tl2Te3 and PbTl2Te3 were deposited electrochemically on Ag substrates at -0.84V and -1.10V respectively. Thermoelectric (TE) material can form a temperature gradient across the material to make electric voltage, which is popular in waste heat utilization and recovery industry. Lead telluride, PbTe, is a small band gap semiconductor of 0.32eV at 300K. PbTe can change its n-type semiconductors with Pb-rich to p-type semiconductors with Te-rich[1]. And it is one of the best TE materials used in thermoelectric generators working between 500K and 600K, or even at a higher temperature of 800K.Three facto,rs play a role in the performance of a thermoelectric material: electrical conductivity (s), thermal conductivity(?), and the Seebeck coefficient (S). These can be combined with absolute temperature (T) to give a figure of merit (ZT) for the material, ZT = s2sT/?. By increasing the electrical conductivity and decreasing the thermal conductivity, which can enhance the ZT value, many efforts, such as alloying with other elements and making the materials nano-sized, have been done to improve its properties recently. Hsu et al. reported that the ZT value of Cubic AgPbmSbTe2+m is increased to 2.2 by doping Ag-Sb to PbTe.[2]."

Jan 1, 2011

By M. Uszko

The climatic area in which Poland is located requires heating the ventilation air at intake shafts during the winter season. Air heating of the intake shaft should ensure safe operation of hoisting devices; while at the same time it also affects the conditions of the mine environment. The paper presents the issues of shaft heating in coal mines in terms of the mining law, the effect on the conditions of the mine environment and heating technology solutions used in the mines of Kompania Weglowa S.A. (KWSA).

Aug 1, 2013

The sixth international symposium on mining with fill nearly coincides with the 25th anniversary of the Jubilee Symposium on Mine Filling. That symposium, held in August 1973 in Mount Isa, in part to commemorate the 80th anniversary of The Australasian Institute of Mining and Metallurgy, was the first in what has turned out to be a very successful series of symposia. Subsequent symposia were held in Sudbury, Canada (1978), Lulea, Sweden (1983), Montreal, Canada (1989) and Johannesburg, South Africa (1993). The series of symposia has now become an established part of the mining industry calendar, and it will be interesting to see which country is given the honour, and accepts the challenge, to organise the next symposium. When the chairman of the conference organising committee invited (or was it instructed?) me to prepare and deliver one of the keynote addresses, his request was for me to be in parts historical, controversial, predictive and entertaining. The mix was left to me, with one proviso - that an early pioneer of mine filling in Australia be given due recognition. The chairman of the organising committee alone will be able to determine if I fulfilled the last objective. My success, or otherwise, with the other objectives will have to be judged by my fellow delegates. One way of predicting the future, or some small part of it, is to revisit where we have already been with a view to determining the existence of any trends that may impact on the future. An historical review of filling practice and research, with special emphasis on Australian experience in particular and worldwide in general over the previous 25 years, will enable me to address the historical and predictive objectives.

Jan 1, 1998

Heatings, fires and explosions in New South Wales (NSW) and Queensland coal mines since 1972, are reviewed. Geological and mine settings are outlined. Where available, gas analysis and critical decisions are discussed. This paper updates work by NSW Department of Mineral Resources (1995) and the Queensland Department of Mines and Energy in a report on fires and explosion in Queensland coal mines (Richardson and Ham, 1996). Incident data has important applications in terms of evidence-based risk assessment and identifying key issues to be integrated into competency based training programs. Predictive indicators are reviewed in terms of coal parameters in seams where the incidents occurred.

Jan 1, 2005

By A. E. Halim, J. F. Brune

Debate continues over whether barricading in refuge chambers is a good strategy to survive entrapment emergencies in underground coal mines, in particular fires and explosions. Unlike U.S. coal mines, Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes the merits and problems of using refuge chambers or self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. We found that using refuge chambers may not be the best strategy during extensive fires or when multiple explosions occur. In these situations, mine rescuers are unlikely to be able to extract miners who are sheltered in chambers and, conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as the level 1 emergency exercises required in Queensland, Australia. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By Danny Chan, Shahram Tafazoli, Nicholas Himmelman, Edmond Chow

"While wearable technology has been garnering attention in the consumer market, enterprise and industry have just begun exploring its potential applications. Since February 2014, Motion Metrics International has been working in collaboration with Vandrico Solutions Inc. to apply wearable technology to improve productivity and safety in the mining industry.This article discusses the value proposition of using wearable technology to deliver critical notifications in mining. The advantages and disadvantages of various form factors are explored. The challenges, both specific to mining and in general to wearable technology, are defined. Finally, the concept of MetricsGear, the first wearable technology platform developed for mining by Motion Metrics International in collaboration with Vandrico Solutions Inc., is described. MetricsGear is designed to notify the user with minimal distraction to keep the user focused on his or her primary task and aware of mission-critical events. This focus and awareness allows the user to work more efficiently and safely. The mining process consists of a series of intricate stages, where certain events or conditions in one stage can have a huge impact on other stages. The notification of these critical events or conditions is vital for ensuring the overall efficiency of the mining process. Critical notifications can be classified as two types: timecritical events and contextual information. Time-critical events are situations where a timely response from a responder can have a significant impact on seizing an opportunity or mitigating cost. Some human-computer interaction (HCI) experts classify notification types based on the interruption, reaction and comprehension (IRC) framework. Time-critical events are classified to have high interruption, high reaction and low comprehension due to their urgency. The responder should have just enough information to identify the crisis and react as soon as possible (Chow, 2014). For example, when a tooth is lost during shovel operation, it is necessary to recover the missing tooth before it jams the primary crusher. The consequence of missing this critical time period is a jammed crusher that can cause the mine to be out of production until the jammed tooth is extracted (Baumann, 2013). In this case, the responder only needs to see an image to confirm if the tooth is missing and information to identify which equipment and when the tooth went missing (Fig. 1)."

Jan 1, 2014

By Thomas J. Peters

The Snowbank study area, which had been proposed as Wilderness, lies about 5 air mi southwest of Cascade, Idaho, and about 60 air mi north of Boise. The eastern boundary of the north-south-elongate study area lies 1-to 2-mi east of Cascade Reservoir; the western boundary is contiguous, in part, with the western boundary of Valley county. The 8,200-acre study area is underlain by Cretaceous granitoid rocks of the Idaho batholith. Three prospects were found in or near the study area during a library and field search. Gold occurs at one 30-ft adit, but the gold-bearing structure appeared too narrow to contain resources. Two other prospects appeared essentially unmineralized. No evidence of geothermal activity was observed. Rock in the area is not potentially useful as dimension stone because it does not split into flat slabs. To be used as aggregate, the rock would require crushing and hauling to distant markets. One of 18 alluvium concentrate (placer) samples contained free gold, worth $1.07 per cubic yard of gravel (at a $350 per oz gold price). No alluvial bars were seen; deposits were too small to contain gold resources or be considered gravel resources.

Jan 1, 1993

?It is not the strongest of the species that survives, nor the most intelligent. It is the one that is most adaptable to change.? Charles Darwin. Canada?s mining and exploration companies have evolved over the past century from essentially a pick-and-shovel industry to a high-tech industrial sector. This evolution has occurred in fits and starts, and has been driven by the shifting environment of economic, technical and social opportunities and pressures in Canada. As labour costs have gone up, and labour availability has gone down, the industry has evolved more efficient processes. As mineral prices have increased or fallen, the industry has evolved either by expanding or shrinking production, or by changing processes to adapt to the newly prevailing conditions. As stringent environmental protection legislation has been implemented, the industry has adapted accordingly, and has substantially changed its mindset to incorporate sustainability into its way of doing business. These changes have occurred over a number of decades, and have usually occurred as the industry?s reluctant response to pressures it couldn?t evade. This model mirrors the classical paradigm of natural selection where evolution is driven by pressures external to the organism (or organization) ? change occurs to the degree necessary for survival and prosperity, but generally no further. In recent years a new paradigm has started to come into play in Canadian mining and exploration. Rather than only a reactive response to the external economic, social and technical factors, groups within the mining community are becoming proactive in developing strategies for future adaptive change. Instead of each against the other, they are developing more sophisticated paradigms where they can both compete against (such as in marketing) and cooperate with (such as for tech development) their fellow organizations. Most importantly, they are seeing individual and national advantage in a collaborative Canadian approach to address the advantages of overseas competitors who often have lower labour costs, lesser environmental standards, or more accessible markets and transportation. This has translated into large-scale mining community support for the Canada Mining Innovation Council, and its programs in exploration, mining, processing, HR development, energy and environmental stewardship. This new paradigm is adaptive to the current environment but is substantially different from the older way of doing business in two major ways ? it is based on a collaborative approach to competitive advantage, and it is highly proactive rather than reactive. All the programs have their priorities determined principally by the mining and exploration companies, whose first obligation is to determine the long-term research priorities of the industry as a whole, rather than for their individual companies. Only after industry consensus on priorities does the research community become engaged in the implementation of specific projects to address those identified priorities. A goal of the program is to effectively create a virtual mining research laboratory, by engaging all the major research centres in the country. This approach is being actively adopted by much of the Canadian mining community, and argues well for the adaptability and long-term survival of mining in Canada.

Aug 1, 2013