Search Documents

By M. Krishna, Jayagopal Uchi1, Shanta Sastry, B. M. Satish

"A well-considered composite of ZA-27 reinforced with weight percentage 0, 2, 4, and 6% of alwninite particulate has been made by compocasting technique. The elastic properties of ZA- 27 /alwniniute particulate composite were determined by using U1M. The results showed that the modulus of elasticity and UTS of the composite gradually increases with increase in the wt.% of reinforcement. However, the overall ductility decreased monotonically with an increase in reinforcement. The results of these tests· as well as the predictions of several model~ for composite strengthening available in the literature were compared with experimental results. The data observed from Young's modulus by measurements studies were compared with theoretical results predicted by Eshelby model.IntroductionMetal matrix composites (MMCs) have received increasing attention in _the recent decades as engineering materials. The introduction of a ceramic reinforcement into a metal matrix produces a composite material resulting in an attractive combination of physical and mechanical properties that cannot be obtained with monolithic alloys. Particulate reinf9rced MMCs among the discontinuously reinforced MMCs have attracted quite a lot of attention both in the industrial sectors and the academic communities. There is an increasing need for knowledge about the processing techniques and mechanical behavior of particulate MMCs in view of their production getting enhanced and their commercial applications becoming wider [I]. Interest in particulate reinforced MMCs is mainly due to easy availability of particles and economical processing techniqu"

Jan 1, 2000

By J. L. Deutsch

Block model estimates are commonly calculated by the well-established technique of kriging. The mathematics are well established, but implementation details require site-specific considerations. Checking and measuring the performance of the estimates is important to ensure the block model is suitable for its intended purpose. There are different criteria for long-term planning and short-term planning. The implementation of kriging should be checked with cross-validation and assessed for conditional bias and departure from theoretical optimality with the calculation of kriging efficiency. A new expression of kriging efficiency, which compares the kriging variance with the theoretically optimal kriging variance, is developed to aid in this assessment. The assessment tools presented here can be applied in a number of situations; however, ordinary kriging with a reasonably large search performs well in most cases.

Jan 1, 2014

By Prashant Dixit, Akhil Singh, Asim Kumar Mukherjee, Sudipta Patra, Veerendra Singh

Phosphorous is an undesired element present in iron ore used in the steel making process. It leads to an increase in overall production cost as well as deteriorated steel quality. The desired phosphorus content in iron ores used in steel making is < 0.1%. Numerous beneficiation studies are mentioned in the literature; however, there is no commercial scale technology established to beneficiate high phosphorous iron. The major phosphorous bearing minerals are apatite (Ca5(PO4)(Cl/F/OH), wavellite (Al3(PO4)2(OH)3·5(H2O)), senegalite (Al2(PO4)(OH)3(H2O), barrandite ((Fe,Al)PO4·2H2O), etc. Ultrafine grinding is required to liberate phosphorous minerals from iron ore minerals and subsequently subject it to flotation, acid leaching, and bioprocessing. The selective flotation of iron ore could successfully reduce the phosphorous content from 0.82% to < 0.20% with the combination of grinding, magnetic separation, and carbothermic reduction. Acid leaching processes are also able to remove ~80% (0.85%→0.16%) of phosphorus; however, these are relatively costly and complex processes. The mechanism of bio-extraction for phosphorous removal is reported as one of the most successful processes. This process is capable of removing more than 80% of the total phosphorous and significantly reducing the phosphorous content from 1.06% to 0.16%. The main disadvantage of this process is that it occurs at a much slower pace. In today’s scenario, ultrafine grinding followed by froth flotation seems to be the most feasible solution for the beneficiation of high phosphorous iron ore in which the concentrate obtained can be utilized for pellet making and ultimately used for steel making processes. Development of additives for leaching, roasting, and bioprocessing can be explored further to make these processes more effective and economically viable.

May 28, 2024

By Kristineq Pankow

The August 2007 Crandall Canyon mine disaster raised national awareness of mining-induced seismicity (MIS) in Utah as well as general interest in how seismic monitoring might improve mine safety in the region. Unlike the situation in most other mining areas in the U.S., local seismographs in Utah?s Wasatch Plateau (WP) and Book Cliffs (BC) coal fields are an integral part of a modern real-time earthquake information system developed by the University of Utah Seismograph Stations (UUSS) as part of an Advanced National Seismic System. The UUSS earthquake catalog contains a continuous record of MIS at all active mine sites in the WP-BC region since 1978 (more than 18,000 seismic events = M 4.2). We describe characteristics of MIS and current seismic monitoring capabilities in the WP-BC region. We then demonstrate, using MIS from an example Utah coal mine, the ability to refine event locations with estimated absolute errors of ~200 m or less using a combination of (1) a double-difference relocation methodology and (2) ground truth information provided by mine operators. This approach enables sufficient spatial resolution to correlate MIS with mining activities, providing a useful tool to help improve mine safety.

Jan 1, 2008

By I. V. Baklashov

Geomechanical conditions of mining operation are determined by varying in time and space mechanical properties and initial state of the rock mass, by geological and technological factors. We define adaptive mining technology as a technology capable of adjusting to changing geomechanical conditions of mining operation. The ongoing research at Moscow State Mining University consisting of laboratory, theoretical, and field investigations aims at the development of theoretical basis and methodology of the system of geomechanical support of adaptive mining technology for the bedded salt deposit in the Urals, mined by room-and-pillar method. This system of geomechanical support is capable of - dynamically assessing mechanical properties and state of the rock mass varying within the panel; - mapping mechanical properties of the rock mass within the panel; - assessing and predicting mechanical condition of load-bearing elements of the rock mass and its changes due to the adjustment of the parameters of mining operation considering the in-situ geomechanical conditions.

Jan 1, 1996

By Scott W. Hazen

COMPREHENSIVE summary is presented of results of several years of research at the Bureau of Mines Mining Research Center at Denver on adapting and applying techniques of statistical analysis in mine and mineral-deposit sampling and in computing grade and tonnage of ore for a mineral deposit. In addition to elementary statistical theory the material presented in the bulletin includes: (1) Certain special statistical techniques that have been found useful in mining applications; (2) problems, implications, and limitations that may be encountered in applying these techniques in mine sampling and evaluation; and (3) numerous examples to demonstrate application of the theory and techniques.

Jan 1, 1967

By A. B. Cecala

Video technology coupled with datalogging exposure monitors have been used to evaluate worker exposure to different types of contaminants. However, previous application of this technology used a stationary video camera to record the worker?s activity while the worker wore some type of contaminant monitor. these techniques are not applicable to mobile workers in the mining industry because of their need to move around the operation while performing their duties. the Helmet-Cam is a recently developed exposure assessment tool that integrates a person-wearable video recorder with a datalogging dust monitor. these are worn by the miner in a backpack, safety belt or safety vest to identify areas or job tasks of elevated exposure. After a miner performs his or her job while wearing the unit, the video and dust exposure data filesare downloaded to a computer and then merged together through a NIOSH-developed computer software program called enhanced Video Analysis of Dust exposure (eVADe). by providing synchronized playback of the merged video footage and dust exposure data, the eVADe software allows for the assessment and identificationof key work areas and processes, as well as work tasks that significantlyimpact a worker?s personal respirable dust exposure. the Helmet-Cam technology has been tested at a number of metal/nonmetal mining operations and has proven to be a valuable assessment tool. mining companies wishing to use this technique can purchase a commercially available video camera and an instantaneous dust monitor to obtain the necessary data, and the NIOSH-developed eVADe software will be available for download at no cost on the NIOSH website.

Sep 1, 2013

By P. G. Vikre

Several factors have caused less emphasis to be placed on geologic mapping in mineral exploration in the last 15 years. These include opportunities for "easy" discoveries of near surface gold and silver deposits in developed countries, and of base metal deposits as well in less developed countries, a decline of emphasis on geologic mapping in many universities, and a decline of useful mapping by government agencies in many areas. Geologic mapping is simply a way of recording geologic observations on volumes of rock larger than can be seen from one place. Since most geologic processes involve systems larger than this, mapping is also essential to understand the significance of observations made on smaller volumes of rock, such as thin sections and sample taken for chemical or isotopic analysis. To be useful, the observations recorded through geologic mapping are then interpreted to arrive at an understanding of the 3D geometry and geologic history of a volume of rock, which is used to direct mineral exploration, or any number of other purposes.

Jan 1, 1995

By Antonio Tafra, Rene Dominguez, James Spenceley, Brady Hays

"Extracting one of the world’s most valuable natural resources — copper — hinges on the availability of the world’s most essential resource: fresh water. But try sourcing fresh water in one of the driest places on Earth, Chile’s Atacama Desert.BHP, majority owner of the Escondida copper mine in Chile’s Antofagasta region and Minera Escondida Limitada (MEL), operator of the mine, were looking for sustainable solutions to deliver desalinated water to the mine, while protecting the environment and complying with the local water authorityregulations.The mining giant chose Black & Veatch to solve this challenge.Solving a global miningchallengeMines use large quantities of water for mineral processing and metal recovery. Water supply, and not mineral ore, is often the major constraint to mining production and development of projects, especially in Chile. Mining operations must have a reliable water source that complies with local regulations, without adversely impacting the environment or affecting the water supply of nearby communities.Worldwide, mining companies and their owners, shareholders and regulators are placing new levels of focus on minimizing the impact of mines on the surrounding landscape and communities. Balancing the economic benefits and needs of mining operations with the potential freshwater impacts requires mines to pay serious heed to the environmental and social issues related to water. Today, mining companies are being proactive and are taking action to protect precious freshwater resources while seeking opportunities to reduce and mitigate their water impact.Delivering a desalination solutionBHP and MEL needed an efficient, technologically advanced seawater desalination plant, along with a conveyance system and infrastructure that would carry desalinated water more than 180 km (112 miles) from the ocean to the mine. Four pumping stations convey the water to a reservoir at the mine site, which is 3,200 m (10,500 ft) above sea level."

Jan 6, 2018

By PAITIP THIRAVETYAN, KANJANA KUDPENG

The aim of this study is to compare amino acids and organic acids in the extraction of gold from silicate ore. Amino acids were found to have higher efficiency of gold extraction than organic acids at the same acid concentration, which is likely due to amino acids having both carboxylic and amine groups in their structure, while organic acids only have carboxylic groups. Five amino acids (glycine, aspartic acid, glutamic acid, lysine and tryptophan) and seven organic acids (citric, malic, tataric, fumaric, oxalic, succinic and ascorbic acids) were selected to investigate gold extraction efficiency. Aspartic acid was found to have greater capacity to extract gold than succinic acid. The optimal gold to aspartic acid molar ratio was 1:6, and low concentrations of aspartic acid extracted 35 to 42 percent of gold from silicate ore within 15 days. Further studies are needed to increase gold leaching and reduce incubation time. The results imply that aspartic acid can be used as an alternative reagent to traditional methods for extracting gold from ore. This method is nontoxic to humans, is environmentally friendly and can have real applications.

By Donna Kliche, Charles Kliche

It has been previously documented that various weather conditions such as wind direction and speed, cloud cover and, especially, temperature inversions can significantly affect the overpressure generated by a blast event (Siskind et al, 1980; Oriard, 1999; Siskind, 2000). The overpressure can be magnified downwind and reduced upwind; a change in the regular profile of temperature with elevation can magnify or focus the sound intensity at some distance from the blast event.

Jan 1, 2011

By Paul G. Swanson

This manual of practice is to be used in combination with the final reports for the study of spoil stability in the Eastern Coal Province. The manual applies the predictive matrices developed in the parent study for use in evaluating the stability of typical mine spoil slopes. The values of internal friction and pore pressure coefficient are derived for many varied slope conditions. The results can be used in conventional stability analysis equations to assist the mine operator or regulatory personnel in evaluating spoil stability from very limited information.

Jan 1, 1983

By M Andrew, D McTiffen, M Adams

A major Ventilation Upgrade Project commenced at the Fosterville Gold Mine (FGM) in 2017 to service the ongoing ventilation requirements of the underground mining operation. The project consists of three large diameter ventilation raises totalling 1100 metres, and new axial primary ventilation fans to upgrade the mine ventilation system. With a mining depth of 1200 metres and a thermal gradient of approximately 2.7 °C per 100 metres of depth, the completion of the Ventilation Upgrade Project is key to the ongoing success at FGM. The Ventilation Upgrade Project will allow continued mining, including high-grade gold deposits, lower in the mine where heat is increasing. Figure 1 below illustrates the underground workings at FGM, and provides a general view of the ventilation upgrade works to establish the new exhaust system from the lower workings to surface. Whilst raisebore pilot drilling the H4760 Return Air Rise (RAR) from surface to 395 metres, the raisebore drill string became stuck in the raisebore pilot hole at approximately 300 metres down hole, presenting a significant technical problem and delays to the project. This Case Study provides an overview of the recovery process undertaken at FGM including the recovery of the stuck drill string. The value of the stuck in-hole equipment, the investment in the shaft site preparation, the collar stabilisation, the underground development to the base of the ventilation raise, the surface footprint prepared for the Primary Fans construction and the limited available space on the site were all motivations to recover the raisebore drill sting and ultimately recover the ventilation raise location. More importantly, the long lead-time required should a new shaft location be the final solution, and the delay this would incur to the ventilation upgrade was unacceptable. Recovery of the drill string was not possible using the capability of the Contractor’s Raise Drill. An alternative method for freeing the drill string was required. A significant amount of engagement with industry was undertaken to seek out potential solutions and draw from the experience of others. All methodologies available were considered and assessed. Ultimately, after several attempts at freeing the raisebore drill string using various methodologies, Adams Drillers and Clear Cut Interventions were engaged to provide a turnkey recovery solution.

Mar 15, 2021

By Wilbert J. Huff

For the past 9 years , the technical studies conducted by the Explosives Division of this Bureau have been summarized in a series of reports issued annually . The following account presents investigations undertaken from July 1 , 1943 , to June 30 , 1944. The work is detailed under a number of main headings corresponding to the organizational structure of the Division , the various activities being under the immediate direction of unit chiefs , who report directly to the author . Specific credit , however , is due to the individual unit leader and his assistants .

Jan 1, 1945

By André Piché

"Over the last ten years, several developments have been undertaken to conceive a machine capable of carrying out simultaneously all the mining tasks in hard rock deposits: cutting, mucking, hauling, ground support and dust control.The main advantages of continuous mining over conventional drill and blast is the elimination of the cyclical nature of the actual methods. Other advantages sought are improved stability of mine openings, higher productivity, lower costs, and a cleaner and safer mining environment. Noranda has con-tributed to these developments in a major way. As a member of HDRK, Noranda participated in the development of two mechanical continuous mining machines; the TM60 and the Wirth. Noranda also undertook a development of its own based on the utilization of electricity to break rock. This technology is called plasma blasting (PBT). The concept of plasma blasting is illustrated in Figure 1.When the operating voltage is reached (18kV), the energy is released through a high current switch (500k A) into a coaxial powercable. It is then delivered to the tip of an electrode inserted into a drill hole which is filled with an electrolyte (water). When the energy reaches the electrolyte, it is instantaneously transformed into a high temperature, high pres-sure plasma that produces a shock wave capable of breaking rock(1).After initial testing of the plasma blasting technology in the lab and in the feld, two experimental platforms were constructed. The first one, a test bench, was erected at the Noranda Technology Centre in Pointe Claire, Quebec.(2)The second one is a rock breaker prototype based on a standard diesel-powered carrier (Fig. 2). Each platform was equipped with a 300 kJ pulsed-power module.In 1993, the rock breaker prototype was used for an extensive series of tests in the field. During that campaign, over 700 oversized boulders were blasted. The results of the tests demonstrated that more durable components for PBT were needed. The test bench was then used to successfully develop and test long-lasting components (probe, switch, cable, connector) that can be adapted to industrial platforms leading to the commercialization of the technology."

Jan 1, 1996

By X. Gu

Mining operations, especially surface coal mines, have great impacts on the local ecosystem and the environment. However, it has been a common practice in mine design that the economic evaluation considers only the operating and capital costs, while the costs incurred due to ecological damage are left out. Such practice underestimates the total cost of mining and ignores the difference in ecological impacts between different mine design alternatives. With growing interest in sustainable development, the mining industry is under increasing pressure to operate not only based on economic and engineering principles but also on principles of sustainability. Therefore, estimating ecological costs of mining and considering such costs in the mine design process is an important step towards reducing ecological impacts at the design stage. The objective of this paper is to quantify the ecological costs of open pit coal mining and to demonstrate the influence of such costs on the ultimate pit design. The ecological costs of mining are estimated based on the areas and types of land damaged by mining activities and the carbon emission from energy consumption. Four major components of ecological cost are identified, namely, lost value of direct eco-services, lost value of indirect eco-services, prevention and restoration costs, and the cost of carbon emission from energy consumption. Necessary equations are given for estimating these costs. An algorithm is described for ultimate pit optimization in coal deposits with near-horizontal coal seams. A case study is presented in which the ultimate pits with and without ecological costs are optimized and compared to show the influence of ecological costs on the pit design outcome.

Aug 1, 2013

By M Salu

Ventilation control devices (VCD’s) and bulkheads are critical controls used for managing risk in underground coalmines. Following the Moura No. 2 mine explosion in 1994, the Queensland Mines Department required that the design of VCDs be based on live testing (such as in a mine testing explosion gallery) and more recently on numerical modelling using measured seal material properties. While the stipulated methods represent an idealistic solution, they are not practical to implement as solutions to daily challenges presented in underground coalmines.Not all VCD’s and bulkheads are placed in areas which have been mined to standard roadway dimensions. Operationally, VCD’s may be required to be placed close to intersections or require large dimensionally different areas (eg overcasts and pre-driven recovery road shutters) compared to the live testing or numerical modelling originally undertaken.This paper describes the various structural engineering methods utilised to account for the design of VCD’s where the operational requirements are non-standard. Siting and construction of VCD’s near the entry of cut throughs and geological structures requires additional design considerations. While VCDs constructed from a single material (eg sprayed mining plaster) are relatively straightforward to design, the addition of multiple openings (doors) or large pipes will complicate the structuralanalysis significantly.Temporary bulkheads used for the containment of grout such as for the construction of pre-driven recovery roads in coal mining have a significantly different risk profile to VCDs and should be designed accordingly. Recent failures and near-misses in such bulkheads have highlighted this issuefor the authors.The existence of an Australian Standard for Underground Mine VCDs and Bulkheads would go a long way to addressing many of the issues raised in this paper. Without a single, industry-accepted reference for VCD design, individual mines will have to continueto exercise their best judgements using whatever local expertise is available to them.

Oct 12, 2022

By Dieter Loh, Mathias Knoll, Florian Werres

When a new tunnelling project starts, it has been a vital tradition for decades to cast and erect master rings horizontally on a flat surface to demonstrate the compliance with dimensional tolerances. Some tenders ask for the erection of two or even three rings upon each other or repeated master ring erections at intervals throughout the project. Especially for large diameters, this is a challenging and risky task for the workforce in the segment factory. A truck-mounted crane is often necessary, and in some cases it can take up to a week to complete a master ring. The concept of virtual rings has the potential to replace this tradition by assembling master rings digitally instead of physically. This is based on a best-fit approach, considering the 3D coordinates from laser tracker measurements of segments or segment moulds. Building a virtual ring, a sub-millimeter accuracy can be achieved, the alignment of neighboring circumferential and ring joints observed, and the fit of bolt holes checked. The traditional method, on the other hand, is discussed controversially despite the significant amount of work and risks—particularly as the horizontal position of the ring and absence of gaskets do not simulate the reality in the excavated tunnel. This paper will highlight the technical aspects of virtual rings, as well as their pros and cons, illustrated by a case study from London Thames Tideway where a total of 30 physical master rings could be replaced by virtual rings.

Jun 13, 2023

By J J. L du Plessis

Escalating energy and electricity costs have become one of the biggest expenditure drivers in mining operations. During the last eight years, energy costs have trebled when expressed as a percentage of total running cost in South African mines. Power consumption on mines is controlled by three main strategies, namely load clipping where energy use is reduced for parts of the day, load shifting where energy use is shifted to other parts of the day, and energy efficiency where energy use is reduced permanently.To reduce the operating costs of ventilating and cooling underground mines continuously, system optimisation studies must be completed. A part of this paper describes methods that can be used to reduce energy usage by optimising cooling and ventilation systems during planning and in existing operations using network simulation models that accurately reflect the current and planned ventilation conditions. These models are used to examine various options for improving the overall ventilation and cooling efficiency. Furthermore, an overview of refrigeration and cooling practices, and ventilation strategies is presented.Ventilation-on-demand and cooling-on-demand strategies have the potential to reduce both the capital and operating costs associated with mine ventilation and cooling systems. In addition, it has been proven that modern strategies and energy-efficient tactics are technically feasible.It is also important that the correct equipment selection is made. This must be based on the best technology with the highest energy efficiency. Where equipment replacement is being considered, energy efficiency must be one of the key decision drivers.In this paper a number of studies were presented and from the experience and the data presented it is clear that a large financial benefit is possible through optimising ventilation and cooling during the planning of mines or within an existing operating mine.CITATION:du Plessis, J J L, 2015. Strategy and tactics implemented to achieve energy-efficient ventilation and cooling of mines, in Proceedings The Australian Mine Ventilation Conference, pp 9–18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Juan M. Pestana-Nascimento, Robert G. Bea, Hamed Hamedifar, Emery M. Roe

The current State-of-the-Practice is grounded heavily on deterministic characterization and assessment of the performance of civil engineering infrastructure. In particular, flood defense systems, such as levees, have been evaluated within the context of the Factor-of-Safety where the computed capacity of the system is compared with the code specified demand forces. Uncertainties associated with the capacity and demand forces render deterministic modeling incomplete. In particular, two structures with the same Factor of Safety can have vastly different probabilities of failure. While efforts have been made to assess levee vulnerability, results from traditional engineering approaches omit important factors because they do not account for uncertainties included in analytical modeling, and natural variabilities, or human and organization factors. This paper utilizes risk assessment methods to advance methods for quantifying the contribution of uncertainties to engineering analyses, and thereby provide additional information to help assess sustainability of geotechnically engineered systems. The probability of failure of a geotechnically engineered system is directly impacted by how well the system is understood, and how uncertainties are incorporated in development of understanding of the system. This paper presents methods to evaluate two types of uncertainties for three potential failure modes of flood protection levees: underseepage, slope (or levee) instability, and overtopping/erosion. These analyses account for two types of uncertainty: 1) Type I – inherent uncertainty, 2) Type II – analytical modeling uncertainty. Human and organizational task performance and information development and utilization uncertainties are not included in these analyses. This paper focuses on the behavior of the flood protection levee system for Sherman Island, a western island in California’s Delta. Sherman Island is of critical importance to California because of the very important infrastructure systems that pass under, on, over, and adjacent to Sherman Island, including: natural gas pipelines, regional and interregional electricity transmission lines and telecommunication facilities, two deepwater shipping channels; and State Highway 160, a link between major transportation expressways. The work evaluates current (year 2010) and future conditions (year 2100) and incorporates variations in capacity and demand arising from projected human response activities and global climate change.

Jan 1, 2017