Search Documents

By S Grönstrand, C. Perez, A. B. Yañez, F. Coddou, P. Morales, H. Elgueta

"The TankCell® 300 forced air flotation cell designed and built by Outotec, with active volume of over 300 m3, was installed at Codelco’s Chuquicamata concentrator in September 2008. After that, a program was conducted, where the new cell was tested against the plant’s existing flotation cells of type TankCell® 160, with an active volume of over 160 cubic meters.Testing program was exhaustive and detailed. Grade-recovery curves for each setup were reported, along with recoveries by particle size. Secondly, operational characteristics like air feed and froth height setpoints, and power consumption are compared side-by-side. As the third topic, gas dispersion characterization included velocity mapping, holdup, bubble size and bubble surface area flux operating range. The fourth area of interest was the retention time distribution (RTD) of the 300 and 160 m3 cells in comparison. A detailed campaign using radioactive tracer tests was conducted to clarify this.All of the investigations mentioned above are reported in separate papers for more detail. The aim of this paper is to collect the key findings, and present them in real terms, always referring to operability and metallurgy of the cells. It is destined for people designing new plants and to those improving and expanding existing ones. The most frequently heard question is: will the new large cells operate at same efficiency as the smaller ones. In short, the answer is: NO. They operate at improved efficiency!INTRODUCTIONIn the last two decades of minerals processing, there have been three dominant trends of development in the flotation technology: equipment scale-up, cell characterization and circuit modeling. Equipment scale-up has been rapid in the past two decades. In the year 1990, the largest flotation cell in use was 50 cubic meters of size. This year, 300 cubic meters is the largest installed cell. Characterization of flotation equipment and circuits is a very popular subject nowadays and has helped many operations to improve their recoveries through better control strategies, for example by using optimized air feed and level control profiles (Gorain, 2005), (Doucet, Gomez, Finch, 2006), or through better maintenance (Coleman, Urtubia, Alexander, 2006). Characterization work is closely linked to circuit modeling. The aim is to produce sufficient amount of data to allow reliable model building. These models are then used to design new circuits and to improve existing ones. So in summary, these three lines of development have slightly different aims – from capital and operational cost to performance optimization. Ultimately, they converge in the same end result – maximizing the profitability of the operation. Following chapters will summarize the extensive test work and scientific studies at Codelco Chuquicamata. The aim was to compare a TankCell® 300 cell, with nominal volume of 300 m3, against two TankCell® 160 machines, with 160 m3 volume in each. The work should yield answers to questions: does the larger cell produce similar results – is the scale-up successful?"

Jan 1, 2010

By Rimas Pakalnis, Tom Brady, Lewis Martin

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate weak rock masses (such as are associated with operations in the Carlin Trend in Nevada) into existing design relationships. The original database that led to most of the empirical design relationships presently employed in hard-rock mining was derived from fair-to-good-quality rock. In this study, the relationship between weak rock quality and opening design (nonentry/entry methods) is being investigated. The common factor in all mines is a weak back or wall. This work attempts to provide tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

By J Johansson

The aim of this paper is to discuss how to form work and organisations in the mines of the future. The Kiruna underground iron ore mine in the far north of Sweden is used as an example on how technical development affects organisational issues like skills, work identity and gender. Over a period of 50 years one can see a transformation of work from manual underground work to automation and remote control from surface level. What characterised the old underground workface was the close relation between man and the hard rock and with arduous physical work under dangerous conditions. Today, the face miners are located on the seventh level of an office building close to the mine. There is also an emerging, and in many aspects already evident, knowledge transformation û from the old and obsolete physical and tacit knowledge and skills (for example the ability to æread the rockÆ) to something new, which can be described as abstract æhigh-techÆ knowledge and skills. The modern technology has created a new type of work û new in terms of competencies and knowledge as well as workload and organisation. At the same time the mining company are recruiting more women and promoting the former pure male work as attractive workplaces for both women and men. All this has effects on how individuals and company create and recreate skills, identity and gender. To some extent the technological development predestines these changes, but there are some choices to be done when forming good work and organisations for the mines of the future. The traditional mining workplace culture and behaviours and the old type of masculinity, the æmachoÆ style, will be challenged by the new æhigh-techÆ work and new competency demands. The changes risk meeting restoring responses, which can have negative impact on the performance of the organisation, for example making it inflexible and perhaps ælaggingÆ behind the technological development. These questions need to be handled when planning future mining.

Jan 1, 2008

By S Warden, T Neville, P Leckie

At its simplest, the classification and characterisation of an orebody is a matter of Where, What and When. Where and with what spatial resolution are measurements taken, What properties are measured, and When are the data acquired, processed, and delivered to create the most value. This paper delves into how existing and near-term advances in measurement technologies, field automation, and whole-system-digitisation are combining to open new routes for mine and exploration productivity improvement. Commencing when the initial exploration hole is dug, the advancement in deployment of survey technology—from expert-operated, to driller-operated, to driller-integrated—is used to demonstrate a template for adoption of higher technology measurements. We then introduce and discuss the multi-use measurement as offering outsized returns from a single measurement run, highlighting two new technologies that acquire rock strength while drilling and downhole assay data as examples. For rock strength, we highlight a novel approach to determining Uniaxial Compressive Strength (UCS) while drilling, its relationship to and advantages over Mechanical Specific Energy (MSE), and how it offers utility to multiple downstream processes. For downhole assay, we detail how a back-tophysics approach to Pulsed Fast and Thermal Neutron Activation (PFTNA) analysis offers significant advantages over other measurement methods and earlier implementations of PFTNA, generating a rich data set that can significantly extend and improve the information on which mining decisions are made. Finally, we discuss the possibilities enabled via optimising data delivery, collection, and curation— noting a fundamental limitation of historical systems and exploring the possibilities that will be unlocked by soon-to-market solutions that better enable Orebody Characterisation data to (virtually) move in space and time with rock material post-blasting. Ultimately, the value of optimising the Where, What, and When from point of measurement to the moment it generates maximum value will create greater life-of-asset production for a lower cost and energy input.

Sep 1, 2024

New Continuous Personal Dust Monitors (CPDM) submitted to NIOSH for approval to sample coal mine dust must accurately measure respirable coal mine dust in mine environments. There are two steps in the process which may be done in any order. The manufacturer is required to submit the results of a comparative underground coal mine dust sampling study, where the candidate CPDM is compared to an approved coal mine dust sampling device (currently the Coal Mine Dust Personal Sampling Unit (CMDPSU)). This testing shall follow the guidelines outlined below and shall demonstrate through weighted regression analysis that the mean coefficient of variation with bias correction is equal to or less than 12.8%. The other step involves laboratory testing to determine the electronic and environmental stability. This testing must be conducted by a private, commercial, academic or other laboratory approved by NIOSH.

Jan 1, 2009

By Gordon L. Draeseke

"Before getting into more specific aspects of my talk today I should put in one disclaimer - one week in Mainland China and one day with Premier Kosygin does not make me an expert on Sino-Soviet affairs nor on Canadian-Chinese relations. Perhaps though there is a message in the fact that one meeting took place in relative openness in China and the other was at least partly in a bullet-proof limousine in Canada. I thought it might be interesting and appropriate to explain something of the forest industry to you who are engaged in the mining industry. Our industry, like yours, is based on a natural resource and the basic activity that we engage in is the extraction and conversion of that resource into saleable materials. However, the fundamental difference between our industries is that our resource is on top of the ground - easily visible and easily measurable, whereas yours is under the ground - difficult to find and, having been found, expensive to measure. A second difference is that ours is renewable while yours is extractive, and you must keep finding more to keep up reserves."

Jan 1, 1971

By M. Olalde, I. Watson

"The consequences of ineffective mine closure in South Africa are evident from the number of abandoned mines and operations on extended care-and-maintenance, the on-selling of mines to less well-resourced companies to close, and increasing illegal mining activities. However, the data to substantiate these observations and provide insight into the underlying issues has not been available. Through the Promotion of Access to Information Act, a list of mine closure certificates applied for between 2011 and 2016 and a list of certificates granted over the same period for all nine regions of South Africa was obtained. From the analysis of this data, we show that the mine closure system as implemented in South Africa is largely ineffective. Although closure certificates are being granted, these are for prospecting sites and small-scale mines, which have a relatively small environmental impact. No large mines of any environmental significance were relinquished over the period under review, with very few applying for closure certificates. Furthermore, the issuing of closure certificates varies significantly between regional offices, with the success rate for applications being generally low and issuing of certificates taking an extended period. IntroductionThere are a number of concerns with the mine closure process as practiced in South Africa, and these have largely been laid at the door of government. Alberts et al. (2017) stress that the legislation generally conforms to international best practice. However, the system is ‘complex and unwieldy’, involving various pieces of legislation and different government departments with overlapping requirements and different interpretations of the law. A further area of concern is the capacity and competence of government to implement legislation. The ‘shortage of relevant mine closure skills and knowledge within the regulator’ was identified by van Druten and Bekker (2017) as a key contributor to unsuccessful closure. Lack of capacity and resources within the regulator has also been highlighted by Botham, Kelso, and Annegarn (2011) and Milaras, McKay, and Ahmed (2014). A recent study of the mineral application process by Corruption Watch (2017) indicates that positions in the regulator have been frozen for many years, leading to a shortage of staff, and that unqualified individuals have been appointed. There is also the perceived reluctance of government to grant closure in order to limit transfer of the liability to the state and delay the inevitable job losses."

Jul 1, 2019

By Karina Forster

Rock mass characterisation is a critical component of effective stope design. Unexpected excessive stope dilution or uneconomic stope sizes can be the result of rock mass characterisation that is not representative of actual stope conditions. Comprehensive characterisation of the rock forming the stope hanging wall, back, ends and footwall is best done by a rock mechanics or ground control expert, however, this is time consuming and is often limited by available access. There are two general approaches for characterising a stope hanging wall for dilution estimating. Detailed classification and mapping data can be collected in local areas where good exposure is available. Personnel, exposure and time are usually not available to do a thorough analysis for all stopes. The stope hanging walls are then broken into lenses or domains and similar conditions are assumed for each area. The second approach consists of using readily available data such as RQD. Other rock mass properties which influence hanging wall behaviour are estimated based on back analysing a few case histories. Stope design is then based on the variability of the one parameter, such as RQD, that is consistently measured for the rock mass surrounding the ore body. This paper presents a third approach which looks, in depth, at the interpretation of geological core logging data for rock mass characterisation. Several rock mass properties that influence stope design, such as joint alteration, rock mass strength, joint spacing and orientations, have been linked to data collected by the mine geologists. This drill hole logging data was calibrated against underground mapping and used to back analyse the dilution prediction for mined-out stopes.

May 1, 2006

By Edward P. Barrett

SPONGE IRON has been defined as the metallic product formed by the reduction (removal of combined oxygen) of iron ore or other iron oxides at temperatures below the fusion point of iron. This product probably derived the name "sponge iron" from its porous nature. When the reduction proceeds at slightly higher temperatures and the particles of metal weld together or finally even melt to yield pellets or balls that lack the porosity and low-density characteristic of sponge iron, the product might more correctly be called "direct iron."

Jan 1, 1954

By R Dimitrakopoulos, I Minniakhmetov

Geostatistical simulation techniques are used to quantify uncertainty of spatial attributes of interest describing mineral deposits, petroleum reservoirs, hydrogeological horizons, environmental contaminants and so on. The majority of existing methods consider second-order spatial statistics and Gaussian processes, while the more advanced multiple point-based simulation approaches are algorithmic and do not consistently account for the high-order spatial relations in data. Recently, simulation techniques for complex and non-Gaussian spatially distributed variables have been developed, based on high-order spatial cumulants, and make no assumptions on data distribution or require data transformations. In this paper, the previous developments are extended and a new approach for the joint simulation of multiple correlated variables using high-order spatial statistics is proposed. The technique is based on a new algorithm for the decorrelation of correlated variables into factors, using the so-termed diagonal domination condition of high-order cumulants. The decorrelated factors are then simulated using high-order simulation and back-transformed into the initial correlated variables. The decorrelation using diagonal domination of high-order statistics is tested with a data set from a multielement iron ore deposit, and then a fully known two-dimensional data set with two correlated variables is used to demonstrate the practical intricacies of the proposed method.CITATION:Minniakhmetov, I and Dimitrakopoulos, R, 2014. Joint simulation of correlated variables using high-order spatial statistics for orebody modelling, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 53–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By T. Rasmussen, T. G. Jørgensen, T. Fischer, R. K. McLimans, C. Knudsen, D. Frei

Ilmenite-bearing paleo-beach deposits were discovered in Jylland, Denmark using a combination of Ground Penetrating Radar (GPR), portable X-ray fluorescence (XMET), bulk XRF analyses, Computer Controlled Scanning Electron Microscopy (CCSEM), and wire line logging. The Miocene-age paleo-beach deposits are located below a thin Quaternary cover in a region of very moderate relief and essentially no outcrop demanding unique approaches in exploration. Initially, an isopach map of the Quaternary is prepared from existing water well data. A geological model for likely occurrence of Miocene paleo-beach deposits is generated and the coincidence of thin Quaternary cover and potential paleo-beach deposits define targets for detailed exploration. The defined targets are traversed with GPR to identify paleo-beach structures which are then used to define a drilling program. This methodology located a paleo-barrier island at the Vorslunde location with more than 10% ilmenite in the sand. During the drilling process, the TiO2 and heavy mineral contents of the sand were logged every meter with a portable XRF unit (XMET) and subsequently calibrated more accurately by comparison to bulk XRF and CCSEM analyses for selected samples. The bulk XRF data also provided more complete compositional information. Insitu determination of geology, heavy mineral abundance, and corroboration of the XRF logging was done using wire line logs, a combination of spectral gamma and induction conductivity logs. Detailed characteristics (abundance, grain size, shape) and chemical composition of minerals was determined by the GEUS CCSEM methodology (Frei et al, this vol.). The average weight percent TiO2 for all Ti-minerals is 62%, 60% excluding rutile. That elevated TiO2 content (>> ilmenite stoichiometric value, ca. 50 %) indicates that ilmenite experienced an iron-leaching environment. The source of the sand deposit was investigated by dating contained zircon. The results show that the likely sources of zircon are in southern Norway and southwestern Sweden with common zircon ages of ca 1100 Ma. and 1500 Ma.

Jan 1, 2005

By J. Mackintosh Bell

External trade strongly influences the well being of all nations. In the modern economic mechanism, no country is so well endowed that it has not to import commodities from others and to export its products in turn to make good its deficiencies, to rectify or improve its financial structure. From the standpoint of international commerce, Canada is strategically well placed. On the south she is bounded by the richest country in the world. On the east she faces the Atlantic, on the west the Pacific. On both coasts there are fine harbours to which lead great lines of railway that span the continent. Canada is now fifth among the exporting nations of the world. For disposal abroad, she has enormous quantities of primary commodities and substantial amounts of manufactured goods as well. But she is far from being self-sustaining. She is unusually dependent on foreign trade, not only because of the commodities she has to sell but because of the lack of many essential articles she does not or cannot produce. To Canada, external commerce is vastly more important than internal trade. The wealth of nations is decided by their ability to produce more than they need, to sell more than they buy, and to build up favourable balances resulting from trade or services. With few countries, however, are returns perennially satisfactory. Fruitful periods are followed by leaner years. In times of prosperity foreign credits are increased, monetary systems strengthened, reserves accumulated to withstand recurring days of strain. Today, the foundations of financial systems are being re-examined, "dogmas hitherto accepted as canonical are being questioned" . It is not only in Europe and America that men search for illumination in problems arising from monetary restrictions.

Jan 1, 1933

By Tassos Grammatikopoulos, Gary Pearse, Massoud Aghamirian, Charlotte Forstner, Stephen Mackie

"SGS Minerals Services (Lakefield, Ontario site) has conducted a number of developmental and pilot programs that examined methods for the beneficiation, extraction and recovery of lithium from a variety of spodumene containing hard rock sources. An overview of the beneficiation programs is presented separately by Aghamirian, Mohns, Grammatikopoulos, Imeson & Pearse (2011). The focus of this discussion will be the hydrometallurgical steps involved in producing a high grade lithium carbonate (Li2CO3) sample from the spodumene concentrate. SGS has applied the standard Li2CO3 hydrometallurgical flow sheet to a number of spodumene concentrates and has determined that all of these samples respond in a similar manner to the process and produce a final product having a Li2CO3 grade of >99.5%. The standard process is sufficiently robust to accommodate the observed variability in the concentrates that have been tested. Advantage of one spodumene deposit over another will thus be gained through process optimization and innovation. Optimization at the beneficiation stage and at the hydrometallurgical stage must be considered. Some aspects of the process optimization of the hydrometallurgical flow sheet will be presented.INTRODUCTION The current activity in the exploration, development, and mining of lithium based minerals is due in large part to the key role that this metal plays in the rechargeable battery industry (U.S. Geological Survey, 2011). Lithium battery technologies are widely applied in a range of portable electronic consumer products. The expanding development and production of hybrid and fully electric vehicles has contributed to the increased interest in finding and developing new lithium sources in order to meet the expected demand from the lithium battery industry. Lithium may be sourced from continental brines (sub-surface salars), hard rock minerals (pegmatite, spodumene), hectorite clay deposits, geothermal brines and oilfield brines. Currently the majority of the lithium products are produced from Li brines. The four major lithium producing countries are Chile, Australia, China, and Argentina (U.S. Geological Survey, 2009; Roskill, 2009). These countries accounted for 97.6% of the total lithium produced in 2010."

Jan 1, 2012

By John R. Goode

"The year 2011 witnessed a major surge in rare earth prices as China, supplier of +95% of the world’s rare earths, reduced export quotas and increased export taxes and duties. In response, companies around the world are scrambling for alternative sources. In Canada too, there is a race to be the “first” rare earth producer. Something that is not generally realized is that Canada has a long history of rare earth production and was a major supplier from the early 1960’s to 1990. At one stage, Canada was said to be supplying more than one third of the world’s yttrium and probably supplied even more than that. Five decades ago, thorium was a key element in many non-nuclear applications and Canada became a major supplier of thorium from the late 1950’s to 1968, first as a by-product of uranium and then as a co-product of rare earths. This paper reviews the development of Canada’s original rare earth and thorium production facilities, which were located in the Elliot Lake uranium camp in Northern Ontario. The uses of these elements, geology, mineralogy, markets of the time, and processing are all discussed. Some of the lessons learned from these pioneering operations might be useful in today’s race to develop the next generation of rare earth production plants.INTRODUCTION The rare earths and thorium were first identified in the early 19th century but were little more than curiosities for the next century. However, in the mid-1960’s the invention of rare earth-based phosphors for the cathode ray tube in colour television sets launched a major demand for certain rare earths. The use of thorium as an alloying agent in aircraft and missiles grew rapidly in the late 1950’s. In the same period, demand for uranium for both weapons and power production soared. Also in the late 1950’s, the Elliot Lake uranium-thorium-rare earth deposits (also known as the Blind River deposits) were discovered. This conjugation of events led to uranium production in the Elliot Lake camp, quickly followed by the co-production of thorium and, later, the rare earths. Uranium production in the Elliot Lake camp continued from 1955 to 1996. Thorium was produced continuously from 1959 to 1969. Rare earths were produced, intermittently, from 1965 to 1990. Complete production records are not readily available for thorium and the rare earths but unquestionably Elliot Lake production made a significant contribution to world production. This paper is intended to present as much of the information that is available."

Jan 1, 2012

By D Morrison, P Goodman

The cycle time between adjacent stopes is critical to achieving the required production rate from 3500 Orebody; one of the Enterprise Mine orebodies. Current Mt Isa cemented fills require a 90-day cure period which had to be cut to 30 days while maintaining the required strength criteria. The Enterprise Mine Feasibility Study recommended that this be achieved by Cemented Slurry Rock Fill (CSRF), but that on-going research into paste fill be continued. The continuation of the research, in conjunction with overseas visits has recommended that the 3500 Orebody be filled with paste fill, with the potential to fill other orebodies. The paste fill will comprise cyclone and thickener dewatered copper tailings to which Portland Cement (PC) is added before vertical borehole delivery and undergound pipeline reticulation to individual stopes. The benefit is not only re-use of copper tailings but also much reduced binder usage.

Jan 1, 1998

By M. R. Shahan, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3000 cfm (1.42 m3 /s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3 /s).

By P. M. Prasad

The last two decades have witnessed the emergence of numerous hydrometallurgical and direct processing techniques for the extraction of some metals from pocketed/lean/complex sulfide ore deposits. A new approach with some inherent technological merits, investigated in recent years, is the lime-enhanced reduction of metal sulfides. Thermodynamic aspects relevant to the lime-enhanced reduction of metal sulfides by H2,C0 and C are discussed. A survey of the researches on the basic features of and factors influencing the lime-scavenged reduction of selected sulfides and sulfide concentrates reveals that lime tremendously enhances the sulfide reduction rates (up to 100 times) and drastically reduces the sulfur emission into off-gas to negligible levels. Further successful practice of lime-enhanced reduction requires only a moderate temperature of reduction (characteristic of each sul¬fide) and, in the case of gaseous reduction, relatively low gas flow rates. Relevant kinetic aspects of the concerned reactions that have a bearing on process development and its understanding are also briefly discussed. A conceptual scheme of general applicability for the processing of sulfide concentrates by the lime-enhanced reduction technique consists of three main steps: (0 lime-enhanced reduction by a suitable reagent (e,g., H,2, CO, gasified coal, water gas), (ii) separation of the product metal from the dry slag (CaS + unused CO) by mechanical separation, magnetic/gravity concentration or flotation and (iii) melting and refining by standard procedures. This novel approach, which is patently less complex, is expected to employ basically simpler flow sheets at comparatively lower operational temperatures and aid in pollution abatement. Potential for developing such a route for the small scale extraction of metals like copper, molybdenum and antimony is indicated. Possibility of utilizing this technique for the production of fibers/ filaments of some metals is also outlined.

Jan 1, 1983

By Moe Momayez

Shotcrete is a practical and economical support system in many Canadian underground mines. Although shotcrete technology has gained acceptance in the mining industry, there are some problems that have emerged with respect to quality assessment and thickness measurement of the liner. This paper presents recent tests performed with a miniature seismic reflection device developed primarily for thickness measurement of this heterogeneous liner. Work was performed on site in an underground mine in Ontario, Canada. This paper also presents the results from laboratory tests performed on fibre reinforced and non-reinforced shotcrete panels that were used to assess the P-wave velocity in both materials. The results of these tests were used in a second on site investigation. The NDT thickness measurements showed good agreement with direct thickness measurement such as coring.

May 1, 2001

By L. Vollert

In-situ recovery of metals is presently experiencing a revival not seen since early applications in amenable copper oxide deposits, uranium and generally applications where neither, porosity and permeability, nor process chemistry have been prohibitively difficult. With ever decreasing grades in current mining operations or Greenfields projects and ever increasing capital and operating costs, in-situ recovery is looked to as the processing option that will both unlock these deposits as well as potentially derive revenue from mineralised waste remaining in the ground once traditional mining and processing methods become uneconomical. In-situ recovery is also being looked to as a mining method that minimises the environmental impact sustained in the application of traditional energy and water intensive mining and processing operations where millions of tonnes of ore are mined from the earth, processed on surface and then disposed of in both waste dumps and tailings facilities. The key challenge facing companies like Newcrest is that these low-grade deposits or remnant mines are generally hard rock applications that require costly methods to liberate the valuable minerals. A further challenge includes identifying suitable chemistries that both facilitate the economic recovery of gold and copper and that may be considered environmentally acceptable. This paper presents a desktop study whereby the issues of access creation and chemical extraction are discussed and evaluated with a view to driving future research in the area and unlocking this application as a real processing option. INTRODUCTION Mining companies are increasingly challenged by low grade, deep and complex ore deposits which are no longer economically exploitable by current methods. The large footprint of current open pit operations can present obstacles for permitting and social acceptance. For these reasons in-situ recovery (ISR) technologies are receiving renewed attention as a technology which could be used to exploit these more complex deposits economically and with less environmental impact. The environmental impact may be further reduced if emphasis is placed on use of renewable energy sources rather than traditional grid power, gas turbine or diesel generators are employed to drive the operation. A potential renewable energy driven ISR mine of the future is shown in Figure 1.

Jan 1, 2019

Classification within the Inferred Resource category is based on geological judgement and the balance of extrapolation versus interpolation that the Competent Person is prepared to accept. These resources are typically drilled at spacings well in excess of the geostatistical range and at a density that is non-uniform. In many cases, a substantial proportion of the available data will be historical, and should be considered with more recent data sources. The provision of a robust geological model will increase the confidence in any resource estimate, and should be viewed as a critical component. The definition of Inferred Resources is of great importance to vein gold projects, since Indicated and Measured Resources generally require costly underground development for delineation. Indeed, many gold vein operations possess substantial quantities of Inferred Resources (>75 per cent) in their resource inventory both at project start-up and during production. This contribution explores a number of the key issues when using the Inferred Resource category and presents four recent case studies.

Jan 1, 2006