Search Documents

By Rudy Tenbergen, Dick Farmery, Jim Naylor

"Paste backfill has replaced cemented rock fill as one of the components to improve ground · control and mine safety at the Macassa Operation of Kinross Gold Corporation in Kirkland Lake, Ontario. It is the first operation to utilize "" flash thickening ""of very fine gold tailings to a paste consistency in the ""Paste Production and Storage Mechanism"", a joint technical development of Inco and GL&V. The tailings paste is mixed with alluvial sand to produce an engineered quality paste backfill. The development leading up to the decision to proceed with this novel technology is discussed, as well as commissioning of the backfill operation.IntroductionThe occurrence of a major rockburst on November 23, 1993 prompted a review of mining and backfill procedures at the Macassa No 3 shaft . This shaft is some 7238 ft deep and lies in a mining belt that is prone to seismic events. The recommendations were to change the mining from underhand cut and fill to mechanized long hole stopping and to look at alternatives to the rockfill backfill system in place. The Macassa cemented rock backfill operation, while producing the desired fill stiffness had drawbacks as compared to paste fill. With paste fill, placement rates are faster, more openings can be filled, it is less expensive and less prone to the occurrences of compensable incidents.Macassa mining personnel visited the Sudbury operations of Inco in 1993, where development on paste backfill was in progress. As some of the R&D was taking place with funding from the Premier's Council Technology Fund of the Ministry of Trade and Technology of the Province of Ontario , Inco personnel at that time did some feasibility and conceptual consulting on the use of paste fill for the industry. Inco had developed the use of alluvial sand paste fill, an engineered blend of alluvial sand and tailings fines and was doing development work to eliminate the ""conventional"" way of producing paste from mill tailing by thickening and filtration. This latter development work was taking place with GL&V Ontario. That work led to the filing of a joint Inca/ GL&V patent application for the PPSM, the Paste Production and Storage Mechanism with all marketing rights being held by GL&V."

Jan 1, 1997

By Gary R. Gavan

This report presents the results of a research project that gathered detailed information on the composition of the population of mobile equipment used in U.S. coal mines. A computerized data bank containing over 19,000 pieces of coal mine equipment in use in 1976 was prepared with a data retrieval program. Operator protective structure technology is reviewed; field problems experienced with ROPS are discussed.

Jan 1, 1978

By Robert B. Hopler

Reefs, exposed rocks, and fast currents made the Hell Gate section of New York's East River a treacherous passage ever since man attempted to sail through the area. As the harbor's importance grew, attempts to improve the channel were made, starting in 1851. This paper discusses the first major organized effort to clear the area, which began in 1869 and culminated in a single large blast in September 1876.

Jan 1, 1981

By David Newman

"Horizontal stress can have a profound effect on the stability of an underground limestone mine. The presence of horizontal stress is usually determined once the mine has been developed and the orientation of headers and crosscuts are well established. Multiple attempts are typically made to control roof falls without re-orienting the mine. Once the decision has been made to change the orientation, pillar centers, mine opening widths, and the question of how to determine the correct orientation must be answered.A case history is presented to illustrate how geologic structure, ground conditions and roof falls in adjacent mines, the World Stress Map (Heidbach et al., 2016), in-mine measurement of “cutter” roof orientation, the orientation of strata offset (cats eyes) within borescope holes, and the diametral deviation method of determining horizontal strain from drill core were used to establish the most likely range of horizontal stress.The main headers were re-orientated in a direction parallel to the median of the range of horizontal stress. The crosscuts were angled 60° to the headers to avoid being perpendicular to the horizontal stress direction. Pillar centers and opening widths were increased in the favorable stress direction of the mains and decreased in the less favorable crosscut orientation. The major principal horizontal stress magnitude was estimated using the strain measurements from the diametral deviation method and elastic modulus obtained through testing.INTRODUCTIONOver the past decade, there has been a significant increase in the number of underground stone mining operations in the United States. As stripping ratios at surface quarries become uneconomical and reach the extent of the mineral boundary, coupled with the encroachment of urban development on previously rural mining operations, the remaining mine reserves are best accessed through underground development.Although the majority of underground limestone mines in the Midwest are in relatively flat lying deposits with minimal geologic structure, many Appalachian mines are in folded and faulted environments. Tectonic horizontal stresses associated with multiple orogenic episodes are locked in the formation and are released as the underground mine is developed.A common misconception is that horizontal stress impacts are more prevalent at shallow depths where the ratio of horizontal to vertical stress may be high. However, field observations and academic research indicates that horizontal stress conditions may be encountered at any depth due to the tectonic compression of the limestone formation (Esterhuizen et al., 2007; Dolinar and Esterhuizen, 2007; Iannacchione et al., 2003; Slaker, Murphy, and Miller, 2017; Kuhnhein and Ramer, 2004). This paper outlines mine design and layout guidelines for the mitigation of horizontal stress impacts on underground stone mining operations through a case history example. This approach to mine planning and the ability to anticipate horizontal stress can significantly improve future production of multiple levels (Newman and Newman, 2019). As underground stone production continues at deeper depths and in more geologically and geometrically complex mining conditions, an emphasis on ground control and the anticipation of horizontal stress can provide safer and more productive single and multiple level mining operations."

Jan 1, 2019

By V. Panayotov, M. Panayotova, R. Villas-Bôas

The "United Nations Framework Classification (UNFC-2009) for Fossil Energy and Mineral Resources 2009” is the international system designed to meet (to the extent possible) the needs and to support the decision making and resources management of private industry investment, governments, policymakers, bank investment, scientists. There are different international and national systems classifying commodities (resources, reserves, possibility and feasibility to extract them, etc.) with their own definitions and reporting terminology which often do not overlap entirely or even differ significantly - thus creating difficulties and problems among stakeholders to understand each other. The UNFC-2009 is developed to allow “speaking in one language”. The paper presents briefly the UNFC-2009. The UNFC-2009 applies simultaneously three fundamental criteria to classify projects: economic and social viability, field project status and feasibility, and geological knowledge (so called E, F and G axes), thus creating a visualized, easily understandable three dimensional system. The E, F and G axis categories are divided to subcategories, using additional criteria. The UNFC-2009 is already applicable to solid minerals, nuclear fuel resources, petroleum. The amounts of solid waste generated by metals production from ores (mining, minerals beneficiation, extraction metallurgy) and its metals content are discussed from the viewpoint of using the waste as resource. An attempt is made to apply the UNFC-2009 to technogenic waste from metals production from ores - both to old engineering constructions (historic mining dumps and reclaimed beneficiation tailings ponds) and new (currently in use) dumps and ponds.

Jan 1, 2016

By M Ziemski

The provision and management of energy in both fuel and electricity forms is an increasingly important consideration for mines. Pressures from communities, governments and markets are increasing towards more transparent and improved energy management. Combined with the energy-water nexus, where water and energy are closely related in the operation of a mine, this emerging business climate means a more thorough and responsible approach is required for the acquisition and use of energy, as well as the release of emissions. Many of the complexities in potential new ore bodies are borne in remote locations, high altitudes, low grades, arid climates and deep deposits. Each of these challenges affects the successful provision of energy. In combination, such challenges can leave an operation seemingly unviable from an energy perspective, especially when approached from a traditional mining energy feasibility lens. This paper discusses some of the energy alternatives currently available and emerging in the mining industry. Both energy supply and demand options are considered, which can provide a very different energy footprint with the flexibility to address, and potentially overcome, major energy challenges for a mine. CITATION: Ziemski, M, 2018. Energy complexities in complex orebodies, in Proceedings Complex Orebodies Conference 2018, pp 106–111 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By M Grigorescu, J H. Hodgkinson, M Khanal

The mining industry often needs to operate in remote or climatically harsh locations. The industry has recently been forced to deal with extreme conditions including floods, heatwaves and droughts. As these are becoming progressively frequent occurrences, mines typically build ‘downtime’ into production schedules and expect to incur costs to manage the various risks arising from climate extremes. Importantly, many environmental conditions are becoming more extreme and consequently, risk management based on past data can become increasingly ineffective. Market and shareholder demand for fewer interruptions are another pressure on mines to avoid prolonged or frequent downtime. Hence, adaptation to climate is becoming an important strategic move for many companies, many of whom are using future climate scenarios and alternative risk evaluations.We present here a method that uses commonly available mine site data to assist decision-making for reducing vulnerability to sudden flood. The method, ‘climate-related adaptation from terrain evaluation results’ (CRATER), identifies a mine’s flood ‘hot-spots’ and presents them as a ‘traffic lights’ warning map. The process then requires a failure analysis process such as fault-tree analysis to identify both the cause of possible failures and a range of possible failure-avoidance adaptations. In the final stage, management can assess the most suitable option for the mine, based on the availability of capital such as time, facilities, labour and money in addition to social acceptability of the options. CRATER has been tested in an open cut mine environment and is now being further developed to identify how subsidence over underground mines may impact on flooding and ponding over the mining life cycle (CRATER II). Further work is continuing to test larger and more complex mine landscapes to deliver a method to extract more knowledge from existing data.CITATION:Hodgkinson, J H, Grigorescu, M and Khanal, M, 2016. Reducing mine site extreme rainfall vulnerability using climate-related adaptation from terrain evaluation results, in Proceedings International Mine Management Conference, pp 187-200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By Z. Henderson, J. Saylor, L. R. Mendoza

"Diesel particulate Matter (DPM) is a byproduct of fuel combustion in diesel engines. It is classified as a carcinogen, with associated respiratory and cardiovascular health effects. The composition, size, and concentration of DPM is dependent on factors such as engine type, loading and fuel composition. Though a number of DPM abatement and control strategies currently exist, particularly in underground mining environments, occupational exposures remain a serious health concern. As a novel abatement approach, DPM scavenging by fine water or “fog” droplets has been proposed and a laboratory set-up has been built to test the efficacy on engine exhaust. Here, we describe a series of tests that varied engine load, system flow rate and fog drop number density. While none of these factors had overwhelming effects on the results within the ranges tested, the improvement in DPM mass removal attributed to the fog treatment was about 45% on average in comparison to no treatment. INTRODUCTION Diesel engines have seen widespread use for well over a century due to their relatively high thermal efficiency and fuel economy1. More recently, however, adverse health risks of diesel exhaust have become increasingly clear. Many of these risks are associated with the physical and chemical properties of exhaust components1–3. The term diesel particulate matter (DPM) is used to refer to the solid components of diesel exhaust, which are a mixture of elemental and organic carbon (EC and OC) and minor constituents including sulfates and metal ash3. The OC fraction of DPM results from unburned fuel and lube oil, whereas EC or soot is formed during the combustion of locally rich regions within the fuel. DPM is classified as a carcinogen6,7 and epidemiological studies have demonstrated a positive correlation between long-term exposure to DPM and other combustion-related fine particulate and increased cardiovascular and pulmonary diseases8,9. Diesel engines operate in relative fuel rich/oxygen lean conditions and are characterized by relatively high emissions of particulate as compared to spark-ignition engines2,3,10. Typically, these emissions range from 107 – 109 particles/cc and cover two primary size ranges: the nuclei mode where particles have diameters less than about <50 nm, and the accumulation mode where diameters are from about 50-10,000 nm. Most OC resides in the nuclei mode as semi-volatile compounds, while most EC is in the accumulation mode3. The physical and chemical properties of DPM vary with the type of engine, fuel (e.g., petro- vs. bio-diesel) and operating conditions such as loading (i.e., a function of torque and rotational speed)2,3,9,11,12. Loading is a particularly important factor with respect to DPM toxicity9,13,14, and on the effectiveness of after-treatment technologies2,3,15. Engine load alone can affect the EC/OC ratio, and the size distribution and number density of DPM. For diesel engines, the load is roughly proportional to the equivalence ratio3, defined as the actual fuel/air ratio over the stoichiometric fuel/air ratio for complete combustion. Light loads generally favor the formation of OC and small particles. As load is increased the volatiles are oxidized leading to larger soot particles (i.e., EC), but lower total number density of DPM. With further loading, the formation of soot offsets the decrease in volatiles, resulting in increased DPM mean size and number density3."

Jan 1, 2017

By P Kumar, J Safarian

Understanding how ore interacts with flux particles at elevated temperatures to create molten slag is crucial since it governs the dynamics of a chemical reaction. This study explores the smelting behaviour of pre-reduced Nchwaning manganese ore when combined with lime, with the objective of examining the evolving interaction between pre-reduced ore particles and lime over time. The research sheds light on the interaction between solid and liquid and the phases that emerge during this process. To achieve this, a sessile drop furnace was employed to rapidly heat the materials positioned adjacent to each other on an alumina substrate and to observe the smelting process as it unfolded over time. This method allowed for the direct observation of the melting temperatures and the flux-ore reaction progression rate, and the potential disruptive events that might occur. By comparing the molten interfaces of the fluxed materials at various time intervals, this study provides insights into the relative rate of slag formation from the two materials. The results indicate that the main slag formation initiated at approximately 1400°C and continued to advance with time, with complete mixing occurring around 1500°C. The possible phases formed were identified using Scanning Electron Microscopy and modelled using Fact Sage thermodynamic software. In addition, the iron particles in the pre-reduced Mn ore were separated and settled from a rich MnO-containing slag. It was found that the separation of molten iron droplets from the slag depends on the rate of solid MnO particles dissolution into the adjacent slag phase.

Jun 19, 2024

By Yuting Xue, Danqing Gao, Brijes Mishra

Heterogeneity and discontinuity significantly affect rockmass strength. Past studies have largely used arbitrary scaling approaches to produce rockmass strength from laboratory rock tests. This paper proposes a stochastic approach to produce rockmass strength from laboratory rock tests. Based on the laboratory data, MATLAB with an extreme value stochastic model generated a database for each physico-mechanical property of the rock. Then finite-difference software FLAC2D simulated laboratory-sized rock specimens. Random material properties in MATLAB were generated using the grids developed in the numerical model. The random properties were then applied to the final FLAC2D model. Model runs simulated the approach performed in the laboratory. The results from the model indicate that a stochastic approach produced compressive strengths that were lower than those from the deterministic approach. Failure modes for each specimen were different from those observed in the laboratory. In addition, random density also influenced the failure mode, highlighting the importance of stochastic analysis in rocks.

By Xiaoping Xu

An albitization granite type tantalum-niobium ore from Jiangxi Province, China was taken as the research object in this paper. The main valuable minerals in this ore are tantalite-columbite and uranmicrolite, and the minerals that can be comprehensively recovered include cassiterite, sulfide minerals, topaz, zinnwaldite, and quartz-feldspar. Based on the research results of process mineralogy, the roughing process of gravity separation for coarse particles combined with flotation for fine particles is proposed. The combined cleaning process of flotation-gravity-magnetic-electric-hydrometallurgical separation is adopted for the rough concentrate of gravity separation while the combined cleaning process of gravity-flotation- hydrometallurgical separation is adopted for the rough concentrate of flotation. High intensity magnetic separation is used to separate and recover zinnwaldite and quartz-feldspar from gravity tailings. By mineral processing for the crude ore containing (TaNb)cassiterite concentrate is 0.0003% with a grade of Sn 63.22% and a recovery of Sn 47.42% while the yield of sulfide concentrate is 0.0783% with a grade of Pb 33.15% and Zn 27.09% which can be separated to get lead and zinc concentrate respectively. The yield of topaz concentrate is 0.1545% and the topaz mainly distributed in the size range of -0.4+0.074mm, which can be made into abrasive products of different particle sizes after classification. The yield of zinnwaldite concentrate is 16.91% with a grade of Liwhiteness of 75%, which is a glass-ceramic material of good quality. 2O5 0.0346%, Sn 0.04%, Pb 0.10% and Zn 0.33%, the tantalum-niobium concentrate with a yield of 0.00278%,a grade of (TaNb)2O5 53.61% and a recovery of (TaNb)2O5 44.49% is obtained. And the yield of 2O 1.34% and Rb2O 0.40%. The yield of quartz-feldspar concentrate is 30.42% with a grade of K2O+Na2O 8.98% and Fe2O3 0.11% and a natural All of tantalum, niobium, cassiterite, topaz, zinnwaldite, quartz, and feldspar are recovered effectively. Keywords: tantalum-niobium ore, gravity separation for coarse particles, flotation for fine particles, comprehensive recovery

Sep 1, 2012

By A. K. Ratte, C. M. Brown

"IntroductionIn autogenous mills, grinding of the ore feed is accomplished by the direct action of the variously sized rocks making up the feed on each other and the mill interior. Size reduction is achieved without the addition of grinding media foreign to the mill feed, differing in this respect from rod, ball, and pebble milling. The term ""semi-autogenous"" has entered common usage in the industry to describe autogenous mills to which supplementary grinding ball additions are made to increase the rate at which size reduction of the mill feed occurs, beyond that achieved solely by the action of rock on rock. In a semi-autogenous grinding (SAG) mill, 50Jo to 10% of the mill volume may be occupied by grinding balls, whereas a range of 25% to 45% is more usual in ball milling.The comminution of mineral ores using ""conventional"" techniques has been described in previous papers. In conventional operations, size reduction of mined ore, and liberation of the valuable mineral content, is typically accomplished using flowsheets employing two to four stages of crushing. Crushing is followed by one to three stages of grinding and classification using various combinations of rod, ball, and pebble mills. This paper describes operations employing autogenous or semiautogenous grinding as the principal stage in the comminution process. Primary crusher discharge, or in some instances run of mine ore, is fed directly to an autogenous or semi-autogenous grinding circuit. Final product sizing may be accomplished in a single grinding stage, the mills operating in closed circuit with classification equipment, or in several stages using autogenous and semi-autogenous mills for primary grinding, and ball or pebble mills for secondary grinding. In several operations a portion of the primary mill discharge is crushed in an intermediate comminution step, these circuits being called autogenousball- crusher circuits (ABC). Many different flowsheets exist, but common and important to most are crushed ore stockpiles, reclaim feeder and mill feed conveyor systems, pumps, screens, and classifiers. Autogenous grinding is employed in both wet and dry processes, although today wet predominate."

Jan 1, 1989

By Jacob Grasmick, Bill Newns

Despite ongoing digitization and “hardware” technological advances, geotechnical uncertainty remains the most significant risk in underground and tunnel construction. And, whilst they are commonly held up as an example of the sophistication of the industry, the practice of drafting and using geotechnical baseline reports is subject to a wide range of influences, not all of which support good risk management. Uncertainties in predicting ground behavior, the gap between the pre-construction assumptions, and the systemic response to construction remains a significant technical and communication challenge. Accordingly, this paper presents a framework to quantify geotechnical uncertainty using geostatistics and translate these into practical tools for ground risk management throughout planning, procurement and construction. Adopting even some of the principles of this framework should provide improvements to contract risk management and should assist to minimize the potential for commercial losses.

Dec 1, 2022

By G Jones

The Singapore Land Transport Authority (LTA) has been procuring the expansion of their underground mass rapid transit rail network at a prodigious rate since the first line opened in 1987. Four lines (149 km) are currently operating and several more lines are at various stages of planning/construction; one of these is the Downtown line stage 2 (DTL 2).DTL 2 contract C917 was awarded in September 2009 for S$320 M. On 18 June 2013 the original contractor became insolvent, leaving the works incomplete. Following a fast-tracked tender process, McConnell Dowell was awarded the S$254 M contract on 29 August 2013 to complete the works. This contract includes two underground stations constructed by cut-and-cover methods and twin bored tunnels between the stations. Each tunnel is 1400 m long, excavated by earth pressure balanced (EPB) tunnel boring machines (TBM) at an average depth of 20 m and segment lined to 5.8 m inner diameter. The tunnel alignment is located under a busy five-lane road lined with prime residential real estate and congested with utilities.To compound the difficulty the tunnels are located within the notorious Bukit Timah Granite formation. This has a very wide range of strength, from below 1 MPa to over 300 MPa. This strength range is a consequence of six weathering grades, from soil to fresh rock, with the fresh granite causing severe abrasion problems. The various grades can occur within a very short distance of each other. Consequently, the problem of supporting a mixed face exists, particularly in the intermediate weathering grades where intact rock is encountered in the invert and corestones within a loose soil matrix in the crown, which can increase the instability by allowing the ground to flow into the TBM.The focus of this paper will be the excavation of the bored tunnels by EPB TBM used by McConnell Dowell to complete these challenging works.CITATION:Jones, G and Shepherd, J, 2014. Earth pressure balanced tunnelling in a dense urban environment, C917A, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 41–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Rafael Valencia-Dongo

Se aborda una nueva metodología de resolución de conflictos en entornos minero-extractivos, que tiene como base la teoría de juegos aplicada a las interacciones de tres actores clave dentro de la dinámica del conflicto social: empresa, Estado y comunidad. El resultado final de este marco es generar un equilibrio estable donde ninguno de los actores del conflicto tiene incentivos para mantenerlo (equilibrio estratégico). En primer lugar, se evalúa la permanencia de conflictividad socioambiental por las acciones de líderes opositores a la inversión. Luego, se desarrolla el marco de resolución de conflictos mineros a través de pactos de contrapeso. Finalmente, se explican las principales herramientas que permiten los pactos de contrapeso en tres ámbitos: comunicación, gestión sociopolítica y fidelización del trabajador minero.

May 22, 2019

By G. J. Joy

Although rates of pneumoconiosis in coal miners have declined substantially in the United States since the passage of the Federal Coal Mine Health and Safety Act of 1969, new cases continue to occur, including cases of rapidly progressive disease. In contrast, Australia?s underground coal mining industry has reported few new cases of pneumoconiosis for over twenty years. Mortality from Coal Workers? Pneumoconiosis in official health statistics and the prevalence of pneumoconiosis among miners screened in x-ray surveillance programs are also lower in Australia. To understand this disparity, the National Institute for Occupational Safety and Health was requested by both industry and labor stakeholders to examine this issue, with the ultimate aim of reducing the rate of pneumoconiosis among United States coal miners. A number of factors, including coal dust exposure, silica exposure, and coal rank were examined as potential contributors to the above observed differences. Comparison of coal rank data from each country did not show any significant differences. Air sample data from the coal mining industries in both countries show that coal dust levels in Australian mines are somewhat higher than those reported in similar U.S. mines; however, quartz exposure for Australian miners is lower than for many U.S. miners. Assuming that quartz is contributing to the greater number of cases of advanced pneumoconiosis in the U.S., more effective dust control measures, as well an independent exposure standard for respirable quartz in coal mining, need to be implemented to prevent this potentially disabling condition.

Jan 1, 2011

By D. Krippner, C. Nexhip, D. George-Kennedy, P. Gebski, R. Kaur, W. L. Ying

ABSTRACT Water-Cooled Tapblocks Are Essential Components Of Modern Smelting Furnaces. Uninterrupted Operation Of A Tapblock Is Critical For The Optimal Operation Of A Furnace. This Critical Function, Together With Exposure To Extreme Conditions, Drives The Need For An Efficient And Reliable Means For Tapblock Monitoring. The Main Objective Of Tapblock Monitoring Is To Help Optimize The Life Of The Tapblocks By Better Scheduling Inner Refractory Relining And Protecting Operators By Preventing Sudden Deterioration Of The Tapblock. A Taphole Acoustic Monitoring (TAM) System Was Developed To Meet The Above Requirements. This Paper Describes The Principles Of The TAM System And Selected Case Studies.

Jan 1, 2013

By Greg J. Hasenfus, Allison M. Haines, Joshua M. Silvis

The floodable volume of longwall gob can be of great importance in developing accurate coal mine operation plans, particularly for mine water management and environmental control strategies. Given the inaccessibility and difficulty in direct measurement of gob characteristics following gob recompression, hydrologic, geomechanical, and spatial data and principles were used to solve for the porosity and height of the residual gob using a mathematical model framework and bulking-based techniques. Based on this approach, gob porosity of Appalachian longwalls appears to be tighter than previously reported, ranging between 4.99 and 14.31%. Residual gob height, as normalized with respect to mine extraction height, ranges between 1.90 and 2.45. A novel, bedding-based bulking approach is ampliative with respect to existing roof caving and bulking fundamentals, as it has greater explanatory value compared with the traditional, lithologic-based bulking application. The efficacy of using the residual gob characteristics determined by the mathematical model and bedding-based bulking is examined using a causal comparative method, whereby time series prediction of historical groundwater rebound is compared with observed mine pool elevation data. Prediction accuracy is significantly improved using a prototype model to calculate void volume of longwall gob, specifically, the dependence of porosity of the gob material upon the longwall width to overburden depth ratio for movement basins of subcritical and critical panel widths. The potential implication of these findings toward hydrologic, geomechanical, and ventilation studies of longwall gob could be significant.

Aug 13, 2021

VOLUME III The objective of Volume III of this report is to provide a concise review of six major types of legal constraints, controls, and regulations on surface coal mining in the United States, as of January, 1976. At the same time, an attempt is made to format the details of federal and state exploration, mining, and reclamation regulations such that point-by-point comparisons can be made and updated as revisions occur. Thus, Volume III should provide both an executive overview and a user&apos;s manual of legal controls of surface coal mining.

Jan 1, 1976

By G F. Brent, S Hawke, M Rothery, P Dare-Bryan

Mine-to-mill studies have previously demonstrated downstream productivity benefits from relatively modest increases in blast energy, or powder factor. These increases have up to now been limited by safety and environmental constraints, since excessive blast energy can result in flyrock, unacceptable vibration, airblast and wall damage.Here, a new blasting method that overcomes these constraints is presented. For the first time it is possible to employ powder factors that are several fold higher than conventional blasting. Independent modelling has shown that such powder factors can potentially increase mill throughput by 20 to 40 per cent. The economic implications are substantial, both in terms of increasing production in existing operations and in consideration of capital and plant requirements for greenfield sites. In addition, mill electricity and grinding media consumption and their associated costs and energy and emissions penalties can be reduced.This method represents a step-change in blasting practices. It involves a novel design utilising dual blast layers within a single blast event, all initiated with state-of-the art electronic blasting systems. The energies in the lower layer can be as high as five times the standard energies, providing for intense fragmentation of the ore. Results from blast models have been confirmed in field trials of the method.Open cut gold mining, in particular, stands to benefit from this method. As gold grades decline, milling costs and throughput increasingly become constraints on production that can be alleviated with this new method. Additionally, it opens possibilities for improved recovery. Blast modelling studies show that dilution of gold ore within the blast can be managed with the new method. Furthermore, it has been shown that vibration from the new method is actually lower than from conventional blasting, allowing the use of the technique in proximity to mine highwalls and other key infrastructure such as underground orepasses.It is concluded that this new method could substantially increase gold mine production and profitability while reducing overall energy consumption and associated emissions.CITATION:Brent, G F, Dare-Bryan, P, Hawke, S and Rothery, M, 2013. Ultra-high-intensity blasting - a new paradigm in mining, in Proceedings World Gold 2013 , pp 395-400 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013