Search Documents

By Thien Sok, Yaojun Lu, Craig Gilbert, Jeremy Scott

Feedwells play a pivotal role in gravity thickeners, governing flow distribution, feed dilution, and flocculation condition during solid–liquid separation. This study presents an optimized design and digital prototyping framework for FLSmidth’s E-volute and E-Duc Feedwell systems, integrating advanced computational fluid dynamics (CFD) with quantitative criteria introduced at SME2024. Building on established FLS technologies, a series of novel configurations were developed and systematically assessed under full-scale and site-specific conditions. CFD provided quantitative insight into flow distribution, feed dilution, and flocculation efficiency, enabling iterative refinement of design parameters. The optimized feedwell demonstrated superior hydraulic performance, enhanced mixing, and improved flocculation outcomes. Beyond the specific design advances, the work highlights CFD as an effective and economical tool for digital prototyping, facilitating early identification of design limitations, reducing dependence on physical trials, and accelerating innovation. The methodology underscores the value of simulation-driven design in advancing feedwell performance and improving thickener technology.

Feb 22, 2026

By T. Holmes, D. C. Russell, G. Jolly

"The AMEC Oakville office is involved in the design and construction of an iron ore concentrator located in Liberia. Currently, the site ships Direct Shipped Ore (DSO) to overseas customers. The DSO mine-site and port can experience heavy annual rainfalls. The IMSBC Code requires that cargoes are only accepted for loading when the moisture content of the cargo is less than its Transportable Moisture Limit (TML). The moisture content of the DSO has, on occasions, risen to near or above its TML. AMEC was asked to advise whether the concentrate produced from the new concentrator would or would not have the same problems with moisture content and ship loading as the DSO.INTRODUCTION Liberia was, at one time, the world’s sixth largest exporter of iron ore and used some of the most modern mining operations of their time. However, the country has not produced iron ore over the past seventeen years because of civil unrest. The return of stability to the country has allowed the redevelopment of the iron ore industry. ArcelorMittal Liberia (AML) obtained a concession for mining in the Nimba County area of Liberia (Figure 1) in December, 2004 and has studied the known iron ore deposits and former mining operations in this area. It began phase 1 operations in June 2011 with the direct shipping of high grade ore at a rate of up to 4Mtpa. The processing of the lower grade ore in phase 2 of the project requires additional processing capability to produce at the design rate of 15Mtpa. DSO and Concentrate The DSO in the first phase is selectively mined at an average grade of 60% Fe, and then crushed and screened to -10 mm with no washing or concentration. Testing of samples has indicated a size distribution that is finer than typical sinter feed material, although critical material below 0.10 mm is low in most cases, and overall the ore is coarser than typical concentrates or ultrafine products (Feasibility study report, 2011). The phase 1 DSO facility will cease operation after the phase 2 concentrator comes into operation."

Jan 1, 2014

By Kul Bhushan

This paper presents the results of lateral load tests on 0.61-m to 1.27-m (24 to 50-inch) diameter drilled and cast-in-place piers in San Diego area residual/formational soils. The test piers were installed and tested in the following soils: Decomposed Granitic Rock (Ktd), Stadium Conglomerate (Tst), and Friars Formation (Tf). Lateral loads of up to 845 KN (190 kip) were applied to the piers in residual granitic soils, and loads up to 1780 KN (400 kip) were applied to the piers in Stadium Conglomerate and Friars Formation. The tests were conducted by jacking against adjacent piers and monitoring the lateral load and lateral deflection at the ground line. Test results indicate that ultimate lateral pile capacities of up to 1800 KN (400 kip) can be obtained for 0.61 m (24-inch) drilled piers with penetration of 3 to 6 m (10 to 20 ft) in the residual/formational soils tested. Lateral load analyses using p-y curves for very dense sand significantly overestimate the observed lateral deflections. For lateral load analyses using dense sand p-y curves, p-multipliers that increase the lateral soil stiffness (p-y curves) by 2 to 8 times are required to match the load-deflection behavior measured in the test piles. When applied to the dense sand p-y curves, the p-multipliers provide a more accurate prediction of load-deflection behavior in the residual/formational soils, and can result in shorter required pier penetration and significant savings in foundation cost.

Jan 1, 2002

By N LaBranche

The resurgence of Silicosis and Coal Worker’s Pneumoconiosis (CWP) in coalmines has placed the spotlight back on the management of worker exposure to particulate matter across all mining sectors (Coal Workers Pneumoconiosis Select Committee, 2017). There already exists a substantial body of knowledge on particulate matter and its impacts upon human health (National Academies of Sciences, Engineering and Medicine, 2018). The contribution of silica to respiratory disease is well known. However, it is also clear that there are major gaps in our understanding. In part, those gaps relate to the contribution to adverse health effects of mineralogical constituents in the dust (LaBranche et al, 2021a). It is also becoming evident that the size and shape of the particulate matter can affect its potential impact on human health. The University of Queensland has developed a methodology for characterising respirable and inhalable dust samples using scanning electron microscopy. Multiple samples from numerous mining operations have already been analysed using the UQ methodology. The process has been successful in showing the variety of mineralogical components and particle size distributions present in various areas of the mines.

May 5, 2022

By James V. Thompson

ENGINEERS from industrialized countries are frequently called upon to examine mining operations in primitive areas and make recommendations regarding mechanization and modernization. They often set forth with self-confidence, knowing full well that all that is needed is their experience and several shiploads of mining machinery, and at times they mentally provide the answers before the problems have been clearly stated. In primitive areas it is absolutely essential that the examining engineer spend enough time at the site to acquire a thorough understanding of what is being done now and why it is done the way it is. The objective here is to state in simple terms some of the problems that may be encountered, in- as much as solutions, if they can be found at all, will differ with each experience.

Jan 8, 1958

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

Dumper operators are frequently exposed to whole body vibration (WBV) in surface mines. Surface mining activities involve the amalgamation of comparatively high intensity of vibration and extended exposure durations. Efficient risk reduction mandates knowing of important phases of a task that poses a threat to health of dumper operators. So far in India very limited studies have been reported on WBV exposure with regard to surface mines. This paper evaluates WBV of dumper operators based on ISO 2631-1:1997 Standards and European Union (EU) Directive 2002 for different phases of job cycle. Six dumpers were considered for this study and the vibration measurements were made for all the four phases of the job cycle by placing the triaxial accelerometer on the operator’s seat-surface and at the seat-back, independently. The findings of the study revealed that the haulage task (loaded travel and empty travel) remains the chief contributor to vibration exposure according to seat-surface and seat-back measurements. Maximum frequency weighted root mean square (RMS) of 1.12 m/s2 and 1.09 m/s2 were reported for empty travel task for seat-surface and seat-back measurements, respectively. For seat-surface measurements based on RMS, Z axis remains as the dominant axis of vibration for all the dumpers during haulage task, whereas for seat-back measurements, the dominant axis varies between X and Y. Exposure action value (EAV) based on RMS has exceeded the threshold value of 0.5 m/s2 for all the dumpers during loaded travel and empty travel for seat-surface as well as for seat-back measurements.

By David La Rosa, Matthew Craft, Lee Julian

Rules of thumb are ubiquitous in blasting. Typically presented as ratios, they assist with the initial assumptions of blast design and provide guidance for best practice. Examples include the blast hole diameter as a function of bench height, and stemming length as a function of hole diameter. The most common rules of thumb were developed in mid-20th century and it is important for a blaster to know if the rules of thumb are still reliable.

Feb 6, 2023

Many mining companies aim to integrate sustainability principles into their new projects. There is an intention for improvement, but frequently this results in little more than 'business as usual' projects that retrospectively categorise controls for environmental and social risks as sustainability initiatives as part of a public relations exercise. The successful implementation of sustainability requires a change of mind-set and behaviours at an organisational and personal level. In addition, sustainability incorporates a very wide range of interests and technical disciplines. One of the key challenges is in understanding how and when to pull these diverse threads together within a project or organisational process. This paper will explore a number of themes: What does it mean to implement a project in accordance with sustainability principles? How far beyond 'business as usual' is it reasonable to go, and what is the business case for this? Why do the intentions for sustainability sometimes fail and how can we prevent this happening in future? People are instrumental in delivering sustainability; how do we embed sustainability thinking into their behaviours and decision-making? The approaches that have been taken to integrating sustainability in design; what has and has not worked and some of the barriers to integrating sustainability into design? The authors will discuss these themes drawing on case studies from URS' experience in integrating sustainability into large projects. The authors will discuss the need for: a strategic approach which provides a simple framework for tactical decision-making and the consequences of taking tactical decisions in the absence of this framework, alignment of the project team and promotion of a culture of innovation, a shift from a risk/compliance mentality to an opportunity identification mindset, and a systematic approach to integrating sustainability into project design processes.

Jun 1, 2010

By Alfred Petrick

This study gives an analysis of the copper system byproducts and discusses the identification and classification of byproduct metals and their supply systems. Arsenic, platinum-group metals, silver, gold, selenium, tellurium, molybdenum, rhenium, uranium, aluminum, magnesium, and byproduct copper, lead, and zinc from complex ores are covered. The report describes several metallurgical systems, the marginal and incremental products costs of byproduct subsystems, industry structure and organization, and the historical data on price, consumption, and supply. Supply curves are presented for about one-half of the byproduct metals studied. The study develops a conceptual framework for analysis by reviewing the present concepts of byproduct supply and the related price theory. It gives the sources of supply of the individual byproduct metals to indicate the importance of the byproduct supply to the total supply. Mills, smelters, and refineries processing byproduct materials for their metal content are identified by geographic location and company ownership, The study also includes information on the reserves-resource base supporting byproduct output, reserve estimates, and the demand aspects of each byproduct metal.

Jan 1, 1973

By Henri-Loui Jacob, Suzie Nantel

"Depuis la fin des annees 1800, la province de Grenville represente pour Ie Quebec une source importante et diversifiée de minéraux industriels. Le Ministère de l'Énergie et des Ressources du Québec, dans Ie cadre de I'entente auxiliaire Canada-Québec, et les compagnies minieres y ant multiplié, surtout depuis 1983, leurs travaux d 'exploration, de cartographie, et d'évaluation pour les minéraux industriels. Ces travaux ant conduit ala découverte et ala mise en valeur de gisements de granite architectural, de graphite, de dolomite et ant aussi permis de repertorier des gîtes et des indices prometteurs de wollastonite, de silice, de calcite. de dolomite, de silicates d'alumine et de terres rares. Les gisements récemment découverts sont actuellement exploités au sur Ie point de l'être et les gîtes et les indices les plus prometteurs ant été jalonnés.ABSTRACTSince the late 18oos, the Grenville Province in Québec has been an important and diversified source of industrial minerals. The Ministere de l'Énergie et des Ressources du Québec, under the Canada-Quebec Mineral Development Agreement, and the private sector have put an emphasis on exploration, mapping and evaluation programs in the Grenville Province for minerals, particularly since 1983. These programs have led to the discovery and the development of deposits such as architectural granite, graphite and dolomite, and have also led to inventories of occurrences and prospects of wollastonite, silica, calcite, dolomite, alumina silicates and rare earths. The deposits discovered lately are presently being quarried or will be in the near future. The most promising occurrences and prospects have been claimed."

Jan 1, 1990

About MAC ? The national organization of the Canadian mining industry ? Mining, smelting and refining of base and precious metals ? Mining of iron ore, diamonds, uranium, oil sands, coal and industrial minerals ? Many associate members ? www.mining.ca

Aug 1, 2013

By Atta Ur Rehman, Kwame Awuah-Offei

This work evaluates the effectiveness of similitude theory in predicting the draft of a rubber tire loader’s bucket during initial penetration. The work uses 1:16 and 1:8 scale models of an 18-t capacity load haul dump, scaled with the Buckingham Pi theorem, to evaluate the prediction of draft and penetration under different operating and different dynamic conditions. We hypothesized that the observed relationships between draft and longitudinal penetration and the operating and dynamic conditions will hold true for an upscaled model. Similarly, we hypothesized that the results of experiments conducted with the smaller scale model should predict the draft on an upscaled model.

By Marcel Vallee, Fernand Dubuc

"The St-Honoré carbonatite complex, located 8 miles north of Chicoutimi, Quebec, was discovered in September 1967 as abnormal radioactivity was detected in the course of SOQUEM's aerial surveys. The complex, covered by a shallow layer of Trenton limestone, has been explored by aeromagnetic, ground gravimetric and magnetic surveys, and 12,013 feet of diamond drilling. Its age, from potassium-argon dating, is 650 million years. The carbonatite is approximately kidney-shaped and has a surface area of 6 square miles, 20 per cent of which is explored. It shows a central core of coarse-grained massive dolomitic carbonatite and an outer ring of foliated dolomitic carbonatite.The exploration work to date has resulted in the discovery, in the foliated carbonatite, of an incompletely drilled niobium (columbium) zone of pyrochlore-bearing carbonatite, at least 1,000 by 800 feet in size. This zone contains 5,000 tons per vertical foot grading 0.86 per cent Nb205 or at least 15,000 tons per vertical foot grading 0.66 per cent Nb205 or 45,000 tons grading 0.48 per cent Nb20s. The pyrochlore contains an average of 64 per cent Nb,Os. The central core contains a zone of rare-earth-bearing carbonatite (as monazite), grading up to 4.5 per cent rare-earth oxide, 3,500 ppm zinc and 290 ppm molybdenum. Stocks of nepheline syenite and magnetite diorite accompany the carbonatite. The total analysis and trace-element contents of typical rocks are presented."

Jan 1, 1970

By B Flynn, P Knights

Low-loaders or 'floats' for relocating equipment in surface mines are limited to a capacity of approximately 350 t. In the iron ore industry it is desirable to be able to rapidly relocate excavators in order to maintain production rates within appropriate quality limits. In addition, the ability to rapidly relocate heavy equipment raises the possibility of improving the quality of repairs by performing maintenance in controlled shop conditions. However, many iron ore operations operate hydraulic excavators in the 600 to 800 t range, with newly released excavator models exceeding 800 t. These excavators are too large to float using conventional technology. This paper examines the potential for using multi-bogie transporters to relocate large hydraulic excavators in surface mines. Recent innovations have seen the development of modular transporters which can be coupled together to achieve larger platform areas. When separated, and with their drive bogies neutralised, these units are able to be towed behind prime movers and relocated between mines via public roads. The potential cost savings for relocating a Terex RH170 excavator in an open pit coal mine are examined. In the first six months of 2008, the analysis showed the potential for a 38 per cent reduction in total travel time with a corresponding revenue increase of approximately $350 k. The paper recommends that a feasibility study be conducted into offering a heavy equipment relocation service within the Pilbara region.

Jan 1, 2009

By M. G. Lipsett

One challenge in applying information technologies in Mining is building a business case. In Mine Maintenance, there is a complex flow of information that contributes to making informed business decisions. By understanding those information relationships and the cost of wrong decisions, analysts can estimate the value of information flow. Developers can then ensure that systems deliver key information in an accurate and timely way. In this paper, general maintenance decision-making is discussed, with examples of how model-based analysis can improve the information delivered to decision makers.

May 1, 2001

By Sara Anderson, Rachel Nicholls, Tim Chapman, Janice Windle

"In city center sites around the world, and in particular in London, foundation reuse is becoming increasingly widespread as the ground is filled with detritus from previous developments. This paper sets out a systematic framework to consider the need for and benefits of foundation reuse and key issues to be resolved for foundation reuse to be successfully adopted on redevelopment projects. Once foundation reuse has been identified as a potential foundation solution there are several key stages in the design and construction process where the decision to reuse foundations needs to be assessed. The paper concludes by emphasising the importance of ensuring that the foundations being installed now can more easily be reused in the future.INTRODUCTIONThe concept of re-using foundations is not new, and has been adopted on an isolated project-byproject basis for many years. However, over the past decade, interest in the potential of reusing existing piles and caissons within Europe has increased significantly, with a growing interest in the United States of America and Japan. The need has been driven by necessity: on many urban sites the space available for new foundations diminishes with each new set of piles, and these problems can only grow in the future.Initiatives such as the European Union's RuFUS (Re-use of Foundations for Urban Sites) research project have resulted in identification of the key issues for technical viability and risk that have previously hampered potential foundation reuse projects.There is a need to define a systematic approach to the reuse of foundations so that the risks associated with reuse can be identified, managed and mitigated. This requires improvements in knowledge to provide confidence in the long term behaviour of the foundation support and address the risks involved in reusing existing foundations to overcome perceived obstacles in making foundation reuse a realistic option for many sites."

Jan 1, 2005

By Xianzhong Hu, Qingbo Yu, Qin Qin

"Oxy-fuel combustion is one promising option among different CO2 capture technologies. The object of this work is to show the effect of CO2 dilution on the laminar flame speed, flame structure and reaction pathway for methane oxidation at O2/CO2 atmosphere. In this paper, kinetic simulations were made using CHEMKIN with GRI-Mech 3.0 mechanism, which was validated by experimental data of laminar flame speeds. The reaction pathway of CH4/O2/CO2 mixture was derived from reaction flow analysis. Results showed that CO2 decreased the flame speeds, lowed concentration of major intermediates and increased flame thickness. The major chemical pathways of CH4 to CO2 have not changed at O2/CO2 atmosphere comparing with O2/N2 atmosphere, but contributions to major intermediates formation from each related elementary reaction have changed a lot. In addition, the secondary chemical pathways of CH3 oxidation became different at O2/CO2 atmosphere.IntroductionNowadays, as the global economy is developing fast and the pollutant levels (especially global warming gases) are increasing, a lot of researches are focusing on new technologies which can cut greenhouse gas emissions [1]. New technologies have been developed, such as high Mild combustion, flameless combustion and Integrated Gasification Combined Cycle (IGCC) technology. Oxy-fuel combustion using carbon dioxide as dilution of oxygen is considered as a promising approach for reducing CO2 emission. The properties of CO2 in flue gas are different from N2 in air. On one side, the transport, thermal and radiative properties of CO2 are different from N2 in air. On the other side, CO2 is not inert but directly participates in chemical reactions and recent researches [2-5] also present the chemical effects of CO2 on oxy-combustion. For these differences above, the characteristics of oxy-combustion are not alike with traditional combustion. It is necessary to develop the investigation of oxy-combustion.In all combustion processes, laminar flame speed is an important parameter, which links to combustion behavior. Analysis of this parameter can provide a better understanding of the effect of CO2 dilution in the process of oxy-combustion. Several investigations of laminar flame speeds of oxy-fuel flame have been improved, including experimental measurements and numerical computations. A.A.Konnov et al. measured the flame speeds of oxy-methane and oxy-ethane mixture using the heat flux method with a flat burner [6-8]. V. Ratna Kishore et al. used heat flux method to measure the adiabatic laminar flame speeds of hydrogen [9] and H2/CO mixture [10]. Adiabatic laminar flame speeds of hydrogen in O2/CO2 atmosphere are much smaller than in O2/N2 or in O2/Ar. The burning velocity of H2/CO mixture decreased with increase in CO2 content in mixture. Jeongseog Oh et al. [11] used Bunsen flame to measure the laminar flame speeds of premixed oxy-methane mixture with angle methods in atmospheric condition (300k, 1atm). The results were SL=29.1cm/s and SL=29.5cm/s respectively derived from oxy-methane from CH* images and Schlieren photos."

Jan 1, 2014

By R. Scott

This article describes and evaluates the establishment of Kuyasa Mining including the search for a suitable deposit, the ongoing lack of finance, and market constraints. Despite the dramatic initial growth and success of their Ikhwezi Colliery near Delmas, Mpumalanga, Kuyasa?s experiences offer some sobering arguments for significant changes to mineral rights ownership, the attitude of financial institutions and government policy if South Africa is to have a dynamic and successful junior and small-scale mining sector.

Jan 1, 1998

By A Grace, C Sennersten, T Taylor, A Davie, R Lyu, D Pentecost, C A. Lindley, J Craig, L De Macedo Camargo

Many underground mine void spaces are not suitable for human entry due to unprotected roofs, instability or having an unknown safety state (eg if they are many decades old). Investigations of these voids may nevertheless be important for general mine safety, for example to detect propagating collapses or water accumulation, prevent accidental intrusion by new developments or drilling to reassess old spaces for re-mining. Robots are an ideal technology for investigating these spaces, especially flying, rotary-wing robots that can access and map vertical structures and spaces while avoiding rocks, water and mud that have accumulated on void floors. To operate in underground mines, we are developing customised unmanned aerial vehicles (UAVs) as well as interactive 3D virtual models of the vehicles and their underground environments for controlling vehicle operation and visualising incrementally gathered survey data. Using a game/simulation engine to provide an interactive interface for UAV operation makes it possible to orchestrate external spatial information and video feeds with in-game cameras for optimal visualisation that is not limited to the position, orientation or field of view of cameras mounted on the UAV. First and third-person points of view with respect to the UAV are provided, together with 2D and 3D gaze tracking to provide effective interfaces for geology and mine engineering experts without the need for specialist UAV piloting skills. Ongoing work is addressing the provision of greater levels of autonomy for these vehicles to support mapping well beyond the line of sight of operators and geological characterisation of rock surfaces using sensors mounted on them, including miniature X-ray fluorescence and Raman spectrometers. Gathered data is fed into more general 3D models of the mine, block models and orebody so that the UAVs function as elements of a mobile perceptual system for intelligent mining.CITATION:Sennersten, C, Lindley, C A, Davie, A, Lyu, R, Grace, A, Evans, B, Pentecost, D, Taylor, T, De Macedo Camargo, L, Craig, J, Salomao, G N, Hellicar, A, Biggins, D, Timms, G, Coombe, M, Shahriar, M S, Smith, G and Rahman, A, 2015. Unmanned aerial robots for remotely operated and autonomous surveying in inaccessible underground mine voids, in Proceedings Third International Future Mining Conference, pp 101–108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By David Forrester

Subsidence beneath the land surface has traditionally been monitored using the most accurate surveying methods of the day. Over the several hundred years of subsidence investigation, these techniques have improved, and thus the accuracy of subsidence measurements has improved. In circumstances where the subsiding surface is masked by water or rock, novel methods must be developed. This method describes the recent successes of subsidence monitoring using advanced bathymeric techniques in the Sydney Coalfield. In order to obtain subsidence profiles above submarine coal extractions, seafloor bathymetry surveys, run before and after mining, have shown that subsidence profiles can be detected, despite the primitive nature of some of the trials. Very recently, there have been considerable advances in this field, associated with the availablity of high-powered personal computers to control data collection and analyse the results. The recent surveys described in this paper have demonstrated the considerable potential for such methods. This paper describes bathymetric subsidence monitoring developed in the Sydney Coalfield, illustrated with some typical results, and summarizes the findings of the research leading to the development of subsidence design criteria specific to the Sydney Coalfield.

Jan 1, 1996