Search Documents

By Donlad B. Lindsay

This report describes a field-test program to determine the effectiveness of a polymeric wall sealant to reduce the excape of naturally occurring radio-active gas radon from the walls of an underground uranium mine into the ventilation air. A 75-foot-long, dead-end drift with a surface area of about 6,000 ft2 was used as the test site in which the average natural radon flux from the normally dry rock was 16 fCi/cm2-s. The effect on radon emanation of wetting the walls with water to a depth of 3 inches was tested, after which the rock was completely covered with a coating of dry-mix concrete to provide a base for the sealant, an acrylic latex. Sealant was applied in two coats to about 0.25 mm thick. An overall reduction of average radon flux of about 75 pct was achieved. Radon production and other environmental values were measured continuously and automatically by a Bureau of Mines data acquisition system. A commercial microcomputer was programed to convert raw data to engineering units and to perform other useful operations while recording all data on magnetic diskettes. Direct measurements of radon flux from the rock surface were made by a charcoal adsorption technique.

Jan 1, 1981

By L. C. IlsLey

Cooperation between the United States Bureau of Mines and the Safety in Mines Research Board of Great Britain, continuous since 1924, has made possible this and other papers on safety subjects. Grateful acknowledgment is made to representatives of the Safety in Mines Research Board of the Mines Department for their assistance in arranging visits to several mine-safety stations, and to F. H. Wynne, Deputy Chief Inspector of Mines, Great Britain, for arranging visits to mines in Great Britain, Belgium, France, and Germany. During the summer of 1927 the writer had the privilege of visiting the mine-safety testing stations in Great Britain, Belgium, Germany, and France, in the order named. All of these countries have large coal mines, many of which are rated as gassy. Therefore, when the installation of electrical equipment is contemplated, each of these countries is confronted with the same safety problem as in the United States - the development of electrical equipment that will not ignite gassy mine atmospheres, should such atmospheres through neglect or accident surround the equipment. The means used by those countries in safeguarding gassy mines should therefore be of general interest to safety engineers in American coal mines, and it is proposed to give a brief survey for each of the four countries mentioned. The first of these surveys will cover conditions in Great Britain.

Jan 1, 1929

By Sebastião Ribeiro, Leonardo Carneiro Sardinha, Alline Sardinha Cordeiro Morais, Carlos Maurício Fontes Vieira, Sergio Neves Monteiro

The glass tube of spent fluorescent lamps is contaminated with mercury, which might be a serious hazard in the case of conventional recycling by melting with other glasses. A possible solution could be its incorporation into a clay body to fabricate common fired ceramics such as bricks and tiles. The objective of this work is to characterize a type of fluorescent lamp glass waste to be incorporated into a clayey ceramic. The characterization was performed in terms of wettability tests to evaluate the interaction between the surface of the clayey ceramic and glass waste as a function of the firing temperature. The results showed that the contact angle decreased with increasing temperature, reaching a value of 79°, at a temperature of 1100°C, but not sufficient to completely wet the ceramic. However, compatible chemical composition and reduction of porosity by the flow of soft glass waste between the clay particles favor the consolidation of the ceramics structure above 900°C.

Jan 1, 2015

By E. C. Westman

Anomalous geologic or stress-induced conditions can create a hazardous working environment for underground miners. Seismic attenuation tomography provides a valuable tool for understanding static and dynamic conditions induced by mining. As a longwall shearer cuts coal, it generates seismic energy. As this energy travels through the rock mass it is attenuated in a manner proportional to the degree of fracturing of the rock mass. By calculating this attenuation at specific locations underground, the degree of fracturing of the rock mass, and hence the relative stress state or material properties can be inferred. The goal of this work has been to create a tool which can be easily used by the mining industry to obtain information about the distribution of stress concentrations or material properties across a broad area in advance of mining.

Jan 1, 1996

By Nicole Peter

When introducing digital training technology a practical approach helps address cultural concerns.  Solutions to help create acceptance are discussed.  Resistance to change may be deeply rooted in traditional mine training personnel.  Traditional training staff members may consider themselves less digitally-savvy and resist technological methods available to them. A transitional approach intended to help mitigate or resolve resistance is presented as a continuous improvement pathway toward full adoption.  This presentation contends every mine should welcome the benefit of a digitally connected critical enabler.  The adoption of a digitally savvy learning centre is often viewed a disrupter to existing practice.  Given a commitment-driven learning centre model, technology offers the opportunity to transition from a compliance-based training model to one of competence.  Learning and Development practitioners should welcome the latest advances in neuroscience, Bloom’s taxonomy of learning model, and principles which guide mine safety training as outlined by the Lowell Institute for Mineral Resources at the University of Arizona. By employing digital applications to include animation, game-based simulations and immersive Virtual Reality (VR) these technologies create a viable digitally-savvy learning centre. We will outline the ingredients of a digitally enabled, or VR, Learning Centre to offer some observed benefits, successes, and potential short-comings. Much excitement in the industry surrounds implementation of simulation and/or VR headset training.  Given fair consideration of these as a ‘fit-for-purpose’ solution we examine the paradigm shift required to create real results for on-the-job learning.  Interim steps may be needed to meet the cultural transformation.   Simpler forms of VR, in the form of 3D models and VR environments as displayed on a large interactive touch screen, can serve to bridge this challenge and address a group learning environment. Features of the interactive 3D technology and ease of adoption are presented.  Usage of the touch screen is similar to that of a smart phone. It may be implemented as an obvious transitional tool.  To help describe merits of the interactive touch screen the presentation points out these sample underground and surface mine training applications. There are 3-D simulations such as ventilation, emergency response, support installation, and mine cycle and activity scheduling programs. These applications offer the ability to conduct entry examinations, complete digital pre-use checklists, and perform planned task observations in the virtual world of work. The tool may be used to teach the flow of hydraulics and do fault-finding on machinery such as loaders and dump trucks. Learners may navigate in a virtual mining environment to identify hazards, detect and assess abnormal ground conditions, address poor design features, and alleviate traffic constraints. It is possible to use connected physical controls to navigate machinery in the virtual environment. We conclude the presentation with a “compare and contrast” approach to cite potential cultural benefits by adopting a transitional method. 

May 4, 2025

By D. W. Rich

An environmental management system (EMS) is a key part of a company?s environmental stewardship. Procedures and practices to continually improve environmental performance can provide great benefits in operating the company. Managing site environmental quality data is a key component of this. An environmental data management system (EDMS) is an important element of the EMS for mining and other projects, providing project staff with the information that they need to make decisions that can have a significant impact on public health. Improvements in computers, data communications, and transfer formats have made it much easier to implement an integrated EDMS program for gathering, managing, selecting, and displaying data from the field and the lab. Software now lets users define sampling plans, create files for field data entry, and print Chains of Custody. Laptop and handheld computers facilitate field data entry and may provide automated communication back to the office. Most labs can now create usable electronic data deliverables. QC checks and limit comparisons can be largely automated. The result is organized data that can be efficiently used for reporting, graphing, and mapping, to better understand project issues.

Jan 1, 2009

By Bob Miller

"All industries have parts and equipment that are exposed to some type of destructive wear. Hardfacing is a cost-effective tool that will minimize wear and increase service life. At first glance, hardfacing can be confusing and troublesome. In reality, it is not.Postle Industries, a manufacturer of hardfacing products, has found that the 22 answers to frequently asked questions may help operators select hardfacing products that are most appropriate for their application. The first 10 questions are addressed in these pages, the full list can seen at Mining Engineering online under the Web-Only Content section.1. What is hardfacing?Metal parts often fail their intended use not because they fracture, but because they wear by abrasion, impact, metal-to-metal contact or some other form of wear, which causes the parts to lose dimension and functionality. Hardfacing, also known as hard surfacing, is the application of a buildup or wear-resistant weld metal onto a part’s surface by means of welding to extend the life of the part. The weld metal may be applied as a solid surface or in a pattern, such as a waffle pattern, herringbone or dot pattern, etc.Hardfacing is becoming increasingly important for many industries to protect equipment that is exposed to wear and abrasion including parts used in mining, earthmoving and construction, oil and gas drilling and steel making and forging. Extending the life of wear parts can save thousands of dollars and improve productivity. Hardfacing can be used to recondition parts that have already been exposed to wear and have lost their useful life, or used in the manufacture of new parts to improve their life before they are put into service.There are three main types of hardfacing applications:• Build-up or rebuilding.• Hardfacing or overlay.• A combination of build-up and overlay.2. What base metals can be hardfaced?Carbon and low-alloy steels with carbon contents of less than 1 percent can be hardfaced. Medium carbon and low-alloy steels are very common since they provide higher strength than mild steels and better abrasion resistance. High carbon alloys may require a special buffer layer.The following base metals can be hardfaced:• Stainless steels.• Manganese steels.• Carbon and alloy steels.• Cast irons.• Nickel-base alloys.• Copper-base alloys."

Aug 1, 2016

By C Hedemann, N Silveste, H Davis, C J. Moran

For nearly two decades water scientists have been debating the need to use appropriate models for the questions being asked and the data available. This paper puts forward a rationale for a hierarchical framework for water balance modelling as it applies to mine sites. The hierarchy is based on the complexity of models and their data requirements. Scientific models are the most complex and require the most data; next is engineering models, then systems models and the simplest representations are given by conceptual models. A position is put forward that systems models have a range of uses that the others do not provide. A systems model, called SiteMiser, is described and its calibration illustrated. The model is applied to seven coal mines from the Northern Bowen Basin in Central Queensland. Currently, there is little relationship between total water use and coal production. This relationship is not any stronger when fresh (raw) water is compared to reused water. Leading practice water use levels are simulated for all sites. The simulation results demonstrate that there is considerable opportunity to reduce water consumption and, in particular, to import less fresh (raw) water to the sites.

Jan 1, 2006

The 32nd annual American Hall of Fame Awards Banquet and Fundraiser, sponsored by the Mining Foundation of the Southwest (MFSW), will be held at the JW Marriott Tucson Starr Pass Resort & Spa on Saturday, Dec. 6, 2014. Each year, one living Hall of Fame inductee, up to three Medal of Merit recipients, honorees from mining?s past, and recipients of an Industry Partnership Award and a Special Citation are recognized for their respective contributions to the mining industry. Armine Frederick Ban?eld Jr., past chairman and founder of Mintec, Inc. located in Tucson, AZ, will be honored as the 2014 Hall of Fame Inductee at the awards banquet. Banfield founded Mintec from his Tucson apartment in 1970 and expanded it to a global operation. Under his guidance, Mintec won the 2013 President?s E-Award for Exports ? the highest recognition any United States company may receive for making a significant contribution to the expansion of U.S. exports. Medals of Merit will be awarded to Corale L. and James A. Brierley, founder and principal of Brierley Consultancy LLC; David Nicholas of Call and Nicholas Inc. and Scott M. Shields of Joy Global. The Brierleys are being recognized for their true scientific partnership with parallel achievements in academia and in business development. Nicholas is being recognized as the co-founder of Call & Nicholas and for his noted expertise in mining geotechnical engineering. Shields is being recognized for his innovative work with GPS integration and for playing a key role in laying the foundation for autonomous mines of the future. As representatives of mining heritage, the Hall of Fame will induct Patrick E. Connor, ?Father of Utah Mining,? for pioneering mineral exploration efforts in Utah; Earl Tappan Stannard, president of Kennecott Copper Co., for transforming Kennecott in to one of the largest U.S. copper producers; Arthur Barrette Parsons, mining editor and author, for his book ?The Porphyry Coppers in 1933,? a seminal work detailing the history and technical information regarding major porphyry copper deposits and Ernest R. Dickie, general manager of Bagdad Copper Co., for his foresight in converting the mine from block caving to open pit. The Industry Partnership Award will be presented to Empire Southwest, a third generation family owned dealership for Caterpillar which consistently ranks among the top Caterpillar dealers worldwide. A Special Citation will be presented to employees of Rio-Tinto-Kennecott Bingham Canyon Mine for their speedy recovery from the massive Manefay slope failure in 2013.Early sponsors include Ames Construction, Asarco LLC; Brierley Consultancy LLC; Caterpillar Inc.; Click Automotive Team; Deconcini McDonald Yetwin & Lacy, P.C.; Empire Southwest; Florence Copper Inc.; Freeport-McMoRan Copper & Gold Inc; Independent Mining Consultants Inc.; Joy Global Inc.; Komatsu America Corp.; Liebherr Mining Equipment; Lowell Copper Ltd.; M3 Engineering & Technology; Modular Mining Systems Inc.; MWH Global; Newmont Mining Corp.; Ram Enterprise; Rio Tinto/Kennecott, Sonoran Process Equipment Co.; Southwest Energy LLC and SRK Consulting. MFSW is a nonprofit organization and its mission to promote the value of the industry to our community and profession to ensure its future success. Funds raised from its annual banquet are principally designated to support the foundation?s education program, a partnership with the Lowell Institute for Mineral Research at the University of Arizona.

By C. Birch, J. Perold

"Due to the challenging geological environment of the Postmasburg Manganese Field (PMF), a study was conducted to determine if any benefits would derive from the inclusion of resistivity data during threedimensional (3D) modelling of the manganese resource. This was achieved by estimating manganese resources from 2011/2012 drilling data and comparing them with manganese resources estimated from the same drilling data and resistivity data collected during 2013 and 2017.Both models were adjusted to limit their extent to the same 3D modelling space. Significant volume and tonnage differences were observed for all lithological units. The greatest differences were noted in the manganiferous zones of alteration – 7.200 Mt for the geological model versus 3.700 Mt for the geoelectric model.This study showed that the inclusion of resistivity data can reduce exploration costs significantly, as a direct consequence of the resistivity data allowing more accurate siting of boreholes. This decreases the number of boreholes, samples, and analyses required due to the 3D electrical delineation of mineralized areas prior to drilling.An additional benefit is the ability to more correctly forecast the net present value of an operation due to more accurate estimation of manganese resources and stripping ratios. This is clearly demonstrated by the estimated gross profit estimation of R409 million for the geological resource model versus R264 million for the geoelectric resource model.The addition of resistivity data can, therefore, reduce exploration costs and can increase confidence in geological and financial modelling. It would be reasonable to conclude that this approach could also be used for karsthosted massive sulphide deposits. IntroductionAccording to Corathers (2014) and Gajigo, Mutambatsere. and Adjei (2011), South Africa holds between 75–80% of global manganese reserves, followed by Ukraine (10%), Australia (3%), India (3%), and Gabon (2%). The known, land-based, manganese resources located elsewhere are estimated at 2%.The majority of economically important sedimentary manganese ore deposits in South Africa are situated in the Northern Cape Province (Gutzmer, 1996). Manganese ores of the Postmasburg Manganese Field (PMF) were discovered in 1922, and the Kalahari Manganese Field (KMF) in 1940. According to Astrup and Tsikos (1998) and Gutzmer (1996), mining of manganese ore from the PMF ceased during 1989 in favour of the superior quality of manganese ore from the KMF."

Mar 1, 2019

By Fredrick L. Johnson

In 1987, the U.S. Bureau of Mines began a study of the 4.0 million acre Toiyabe National Forest located in eastern California and western Nevada. This report is a compilation of published, company, and field data for part of the Paradise Range, Nevada. The information is intended to aid the U.S. Forest Service in their long range management of minerals and augment the USBM data base. The Paradise Range study area, located 60 air mi northwest of Tonopah, NV, encompasses about 100,000 acres of which approximately 71,000 are administered by the USFS. The area is in the Basin and Range Province and consists of an east tilted block of sedimentary, metamorphic, and volcanic rocks which have been intruded by granitic rocks. Three major mining districts, the Ellsworth, Gabbs, and Fairplay are in, or extend into the study area. The earliest recorded mining activity occurred in the Ellsworth district in the early 1860's. Commodities produced from the study area include gold, silver, copper, lead, zinc, mercury, tungsten, iron ore, magnesite, and brucite. The Phelps Stokes Iron mine has produced about 1.1 million tons of iron ore, the Baxter-Hancock mine has produced over 10,000 stu WO3, and the Gabbs Brucite-Magnesite mine has produced millions of tons of brucite and magnesite. Numerous other mines have produced, but quantities are relatively small. According to company information the Gabbs mine, currently producing, has brucite-magnesite reserves that will last at least 50 years at current mining rates. One hundred thirty one million tons of identified copper-molybdenum resources exist at the B.C. Springs prospect according to company information, but molybdic oxide (Mo03) prices would need to double or triple from the current $3.00-3.10 per lb before mining of the deposit would be economical. Most company exploration activity in the study area is now focussed on precious metals. Active, or recently active mining claims appear to cover more than one-half of the 100,000 acres studied.

Jan 1, 1991

By T. Yamazaki, T. Goto, R. Arai, N. Nakatani

The importance of cobalt-rich manganese crusts on the Pacific seamounts for possible future rare metal sources has been recognized these 30 years. The thin layer-type coverage and the micro-topographic undulation of basement affect not only the excavation efficiency but also the economy of mining venture. Because of these distribution characteristics, no economic feasibility has been recognized through the past economic analyses. On the basis of a recent geological study about seamount rocks, a possibility of by-product substrate recovery for phosphorous supply with cobalt-rich manganese crust mining has been highlighted. In the mining model, the substrate rocks are utilized as phosphates for agricultural and chemical usages. Under some preliminary technical and economic assumptions, the possibility of cobalt-rich manganese crust mining venture is examined. The results show a better economy of the venture including the substrate rock usage for phosphorous supply. Introduction Cobalt-rich Manganese Crusts and the Economic Feasibility Cobalt-rich manganese crusts on the Pacific seamounts received attention as potential sources for strategic metals such as Co, Ni, Cu, and Mn, due to their vast distribution and higher cobalt concentration than manganese nodules (Cronan, 1980; Halbach, 1982; Manheim, 1986). In the earlier stage, the geological distribution characteristics were reported (Cronan, 1984; Clark et al., 1984; Misawa et al., 1987; Pichocki and Hoffert, 1987) and a systematic feasibility of the mining was studied (Hawaii DPED, 1987).

Jan 1, 2018

By F. A. Rutledge

[An a part of the United States Department of the interior program for the development and use of Alaska raw materials, the Bureau of Mines is conducting an investigation of deposits of nonmetallic minerals accessible to the Alaska Railroad for use in building; materials is In the Alaska Railroad-belt area. The results of the investigations, to date, indices that raw materials for the preduction of brick products are in plentiful supply as cloy in the Anchorage area, as fire clay at Sheep Mountain, and as shale in the Healy Creek coal formations near Healy, Alaska.]

Jan 1, 1953

By Chris Twigge-Molecey

Demand for metals will continue to grow as global population numbers and prosperity levels steadily increase. Consequently, there will continue to be a need to design and construct new metallurgical plants. Business success in general requires projects to be financially successful and return appropriate value to their owners. However, in the metals industry, private and public sector financing sources have become very sensitive to the perceived inability of projects to contain costs and meet other business objectives. Thus, the capital for projects has become more difficult and expensive to obtain. It is instructive to note that Ernst and Young (2011) identified that: “Delivery of predictable project results bestows competitive advantage and market confidence to those corporations who successfully instill this discipline”. The implication for future projects is that they must be systematically developed to minimize perceived risks—and more importantly—to demonstrate that the risks are managed to achieve the business case. Then, provided that the project has been developed in a well-structured way, project success can again be defined as a project with: a final cost within 10% of the budget approved at the end of FEL3, when the project is properly defined and the permit conditions are agreed upon; a start-up date within three months of the definitive, scheduled startup date; production levels at 85% of design capacity within a year of starting commercial operation; production meeting the target environmental restrictions; and with zero lost time accidents during construction and startup. The plant design is one of many integrated activities required to achieve these objectives. This book represents a valuable link between the existing engineering literature that encompasses a wide range of engineering fundamental textbooks and design manuals and the project management literature such as the Project Management Body of Knowledge, or PMBOK® (Project Management Institute, 2014). It is evident throughout this book, that the design team is a small but essential part of a much larger project team comprising the project management, construction management, and construction contractor staff. Design activities must be regarded and managed as part of the integrated whole, with two fundamental links throughout the design process:

Jan 1, 2015

By T. Krichler

"Current mine control stations are either single-position systems with high engineering effort or all-in-a-box solutions with low integration possibilities of third-party devices. Above all, both approaches are cost-intensive and not feasible for small companies. This paper shall be an inspiration of how to enhance the productivity and monitoring of an existing mining system in a modular way by introducing a proven technique of the ongoing digital revolution: A Wi-Fi network based on the communication protocol OPC UA. The starter kit consists of a single-board computer, a WLAN access point and any electronic sensor. INTRODUCTION The majority of the European mining industry is run by small and medium deposits (Europe Geology, 2017). This is due to the fact that most ore mines in Europe are widely distributed within the continent, are generally small and additionally they are often steeply inclined. Such ore bodies are normally mined with underground mining methods and must be excavated with high selectivity because of their small thickness. That is why the economy of scales, higher efficiency through bigger machines, cannot be used in most deposits in Europe except for lignite mines. It is important to find an alternative possibility to improve the efficiency of European mines for making them competitive internationally. For cost optimization and profit maximization it is necessary to use the trends of industry 4.0 and to broadcast these into the mining industry to reach a technological advantage. The goals of the EU within the Horizon 2020 funded project are to shorten the actualisation of the mine and block model to hours, improve the communication with Through the Earth (TTE) via very- or ultra-low frequency for long-time monitoring of the abandoned workings, and develop a cost-effective mine control station for optimization of mining processes in Small and Medium Enterprises (SMEs) as well. This paper deals specifically with the new approach for data acquisition, transmission and visualisation of a mine. SCADA AND ERP IN MINING There are already many Supervisory Control and Data Acquisition (SCADA) and Enterprise Resource Planning (ERP) programs on the market, but these are normally not developed for the mining industry. At the moment this leads to three options. • To hire a system integrator, who shall build a complete control station for one mine that requires a high amount of knowledge in programming and cannot be maintained by the mining company itself. • To buy different types of out-of-the-box systems, whereby every system can include some of the used technology. In this case a huge amount of project engineers and operators – at least one per system and shift- is required. • To buy every machine and program from one company including the service contracts."

Jan 1, 2018

By Michel Rodrigue, Sylvain Duchesne, Louis Racine

"LocationThe Louvicourt mine is located 20 km east of Val d'Or in Abitibi, in the northwest part of the province of Quebec. The mine is located on Highway 117 connecting Val d'Or to Montreal and very close to the main railway networkHistoryFive successive exploration attempts by Aur Resources resulted in the discovery of the large Louvicourt orebody in June 1989. Construction of the surface and underground infrastructures commenced in the spring of 1991. Milling operations commenced in July 1994. The entire project cost CDN$290 million, almost CDN$20 million less than initially estimated. The concentrator infrastructure cost CDN$64 million.Louvicourt mine is owned in partnership by Novicourt Inc. (45%), Teck Corporation (25%), and Aur Resources Inc., the administrator (30%).Brief DescriptionLouvicourt mine is the largest producer of base metals (Cu and Zn) in Abitibi-Temiscamingue. Its average daily production is nearly 4300 t of ore, for an annual production of 200 000 t of copper concentrate (28% Cu) and 33 000 t of zinc concentrate (57% Zn). After only a few weeks of operation, it had attained its objectives for the most part, and operations continue to be improved."

Jan 1, 2000

By Phillip M. Busch

VANADIUM was discovered in 1801 by Andres Manuel del Rio, a professor of mineralogy at the School of Mines in Mexico City. Del Rio called the new element erythronium. Later, he decided that this was not a new element but a form of chromium. Not until 1831 did Nils G. Sefström, a Swedish chemist, positively determine that the metal was a new element which he named vanadium, after Vanadis, the Scandanavian goddess of beauty. From 1831 to the 1860's and 1870's, the comparative scarcity and high cost of vanadium restricted its commercial use. Shortly after 1870, more information was obtained on the physical and chemical properties of the element. Thereafter, research on vanadium has dealt largely with its use as an alloying element in steel and nonferrous metals. Vanadium is a widely distributed element in the earth's crust. It is more abundant than many metals but is disseminated in small quantities throughout a great variety of rocks. Relatively few deposits have contained ore of a grade suitable to warrant development for vanadium alone. It is produced in conjunction with uranium, iron, titanium, aluminum, and lead-zinc ores.

Jan 1, 1961

By McHenry Mosier

Mechanical loading, adopted long ago in open-pit, coal, and non-metal mines, was not used extensively in underground metal mines until the World War. In less than a decade it became standard practice in underground work in many mining districts. In 1924 the Missouri School of Mines and Metallurgy, in cooperation with the Federal Bureau of Mines, published a bulletin entitled "Mechanical Underground Loading in Metal Mines," which was prepared by Charles E. van Barneveld, mining engineer, Bureau of Mines.

Jan 1, 1940

By J. A. HUFF, V. V. BAKER

This circular is intended to present in brief form the statutory provisions of Pennsylvania regarding mining operations, in force at the end of the 1931 session of the legislature. lo reference is made to general laws which affect mining only incidentally in common with other subjects, such as the workmens compensation law. The statements have been condensed as far as practicable, and provisions not deemed of general interest, such as matters dealing only with administrative details, have been omitted. This circular obviously is not written with such particularity as to be of great value to the legal profession, but it is hoped that it will be beneficial to the mining industry in giving this information in a relatively compact form. At the end of each paragraph the statute from which it is derived is cited to facilitate reference to the text of the law. It is planned to publish additional circulars from time to time dealing with the mining laws of other States. Any criticisms of the form of publica- tion followed herein, or suggestions aimed at the improvement of future circulars, will be welcomed.

Nov 1, 1932

By J Johansson, J Lööw

Attractive mining workplaces are good, safe and healthy environments. They are also workplaces that the workforce of the future wants to work in. As skilled miners and engineers are already scarce, this is important both for today and for the future. However, the future of mining will also be subject to increased international competition. In attempting to become more competitive, many mining companies turn to rationalisation, looking to both rationalise their production and organisation as well as optimise their processes. Work organisation is important in both rationalisation and providing attractive mining work. As a result, this paper investigates a ‘lean production’ (LP) philosophy for the organisation of future mines. The aim of the paper is to investigate to what extent LP can be used to organise for attractive mining. It first defines what attractive mining work is and to what degree it can be influenced by work organisation. A short insight into the LP concept will be given as well as a review of how it is discussed and utilised in mining today. In conclusion, a summary of LP’s potential to realise future attractive mining is given.CITATION:Lööw, J and Johansson, J, 2015. Work organisation for attractive mining – lean mining and the working environment, in Proceedings Third International Future Mining Conference, pp 197–204 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015