Search Documents

By R. L. Handy

The objective of this research was to devise and test an apparatus to rapidly evaluate the cohesive and frictional strength of coal in situ, in order to increase the safety and percentage of coal recovery from underground coal mines. During the first year device was designed utilizing the bore-hole shear test principle from soil shear strength testing: Two opposing corrugated plates are forced outward to exert a controlled contact pressure against the sides of a previously bared hole, and then the plates are very slowly pulled along the axis of the hole to cause shearing of coal in contact with the plates. Results with the device are expressed in terms of a friction angle[_] and a cohesion c. The [ ] angles obtained from an Iowa coal arc in close agreement with and fall between results from triaxial and direct shear laboratory tests on the same coal. The measured cohesion was found to be much less than from the comparable laboratory tests. It may be increased by pre-stressing and other techniques to embed the shear plate teeth for the first shear test point.

Jan 1, 1973

By Svatopluk Zeman, Zbynek Akstein, Jiri Pachman, Ahmed Elbeih, Marcela Jungova

BCHMX (cis-1,3,4,6-tetranitro-octahydroimidazo-[4,5-d]imidazole or Bicyclo-HMX) was studied as an energetic component of three different plastic explosives based on three matrices: C4 matrix, semtex10 matrix and silicone matrix. The original plastic explosives, Composition C4 - based on RDX (1,3,5-trinitro-1,3,5-triazinane), Semtex 10 explosive based on PETN (pentaerythritoltetranitrate) and plastic RDX-silicone, were included for comparison. Sensitivity and performance parameters were studied.

Jan 1, 2011

Prier to the date of this contract, Ocean Energy had developed and demonstrated a high efficiency fluorescent caplamp which operated from a standard 4 volt miner's caplamp battery. This unit produced about five times the light output of the standard incandescent miner's caplamp. The Company believed that the major market for this unique caplamp was in the industrial and municipal applications. Because of the additional safety requirements for coal mining use, and in conjunction with the much smaller market in the mining industry, the additional expense and difficulty of modifying this caplamp to comply with the Federal and State coal mine regulations were not considered at that time. Recognizing the potential of this lamp for improving illumination conditions for underground coal mining, the US Bureau of Mines contracted with Ocean Energy to make the required modifications to this lamp to bring it into compliance with the Federal and State of Pennsylvania regulations, and thereby, make this lamp available to the anthracite and bituminous coal mining industry. At the outset of the contract, the injection molds for the caplamp housing were being completed, and only prototype, hand fabricated, units were available for tests. The Bureau evaluated these prototype units and formulated a performance specification for the miner's version. Light level and distribution, weight, size, angle of tilt, and operating duration were all specified. In addition, it was required that the caplamp be com¬patible with existin charging equipment at the mines and that the final design be in full compliance with MESA Schedule 6D and he ultimately approved by MESA, Approval and Testing, as well as by the Pennsylvania Bureau of Deep Mine Safety. The scope of this contract covered the modifications required to achieve these objectives. It was agreed by the Bureau that all rights to the lamp, including design, material combinations, circuitry, etc. would remain with Ocean Energy. The charger/adapter system and components, which were developed under contract funds, are disclosed hero and become public knowledge and property. Patent applications have been filed by Ocean Energy to protect the mechanical and electrical design aspects of the lamp. It should be noted that this report contains details, designs and data which may be covered by one or more Ocean Energy patent applications, and disclosure herein is made only to provide better understanding of the contract results.

Jan 1, 1975

By A J. H Newell

The background and the basis for conducting a Technical Due Diligence are discussed as well as the source information, typical studies and potential limitations. Typical short comings including ‘show-stoppers’ are presented for the metallurgical area, with examples. Issues found in other areas such as geology, mining, infrastructure and financial evaluations are briefly reviewed, highlighting the input and interaction required by metallurgists with these disciplines. A checklist is provided as a guide to maximise the success of a Due Diligence as well as a check on the quality of a Feasibility Study.CITATION:Newell, A J H, 2015. Fatal flaws in technical due diligences, in Proceedings MetPlant 2015, pp 61–77 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Steven K. Ruggieri

This report describes the use of the sprayfan auxiliary ventilation system for methane and dust control on continuous miner sections to potential users. The sprayfan auxiliary ventilation system is a modified water spray system which directs intake air to and across the front of a continuous miner to prevent build up of methane gas and dust concentrations. This user's manual contains practical information concerning sprayfan: a. Description and capabilities b. Design c. Installation d. Operation e. Maintenance. Underground tests, independent laboratory tests, tests by MSHA, and independent installations by coal producers have confirmed the performance of the sprayfan system. There are currently 150 sprayfan systems in operation in underground coal mines.

Jan 1, 1981

By Douglas B. Silver

"Editor’s note: Douglas B. Silver, Portfolio Manager, Orion Resource Partners, was the keynote speaker at the 2017 SME Annual Conference & Expo in Denver, CO on Feb. 19, 2017. He also gave the keynote address to the SME Annual Conference in 2008. The following is his 2017 keynote address with a few of the slides that were presented. The full speech is available on YouTube https://www.youtube. com/watch?v=uF0qwGJIX3UIn 2008, I had the privilege of giving SME’s keynote address. At that time the financial markets were on the verge of collapse and my presentation described the issues. Unfortunately I was correct, and global markets went into a steep nosedive, creating the largest economic downturn since the Great Depression.In hindsight, there were plenty of signs that this was coming. The Supercycle had created massive new wealth. This wealth was largely invested in the United States due to the country’s political stability and credit worthiness. In 2004, the large investment banks convinced the U.S. Securities Exchange Commission (SEC) to allow them to triple their borrowing leverage ratios. This made the banks more vulnerable to market volatility. The banks then lent money to NINJAS - people with no income, no job and no assets. Even worse was the fact that these unqualified home owners used adjusted-rate mortgages (ARMs) which they, of course, intended to refinance prior to interest rates rising. These mortgages were then bundled up by the banks and sold to investors as “safe” investment products. The money flowed into these products because the rating agencies gave these instruments high marks. These same agencies earned their fees from the very same banks seeking high ratings. (No conflict there). Private debt exploded and peaked out in 2008.These mortgage products were sold in an unregulated shadow banking system and the ARMs came due. Toxic mortgage default rates skyrocketed and the mortgage-backed securities collapsed in value. This house of cards had a negative feedback loop that accelerated the market crash and resulted in more than $1.5 trillion being lost in the securitization sector, a 47 percent decline in the Dow Jones Industrial Average, foreclosure rates skyrocketing and housing prices collapsing. The financial markets were in a nosedive."

Jan 8, 2017

By Alexander Darío Huamán Ccorahua, Cayo Fernando Soto Buendía, Jhonatan Raphael Rojas Ventura

Lithium is a top-quality mineral in the energy market, with growing demand. It has many applications in medical, nuclear, and energy industries. The purpose of this article is to quantify and analyze the economic potential and projected global demand for lithium annually. It aims to determine Peru’s (specifically Puno) positioning in the global context in 2025 and 2030. The article also seeks to identify the main regulatory, environmental, and social challenges to sustainably exploit lithium in Peru. The study employs applied research (mixed approach), descriptive-correlational scope, and observational, crosssectional design. The methodology demonstrates the use of statistical techniques to model and make predictions about this energy-transition metal. Academic sources were reviewed to enable a comparative approach and projection into the future of lithium for development in the mining industry. In the last 10 years, lithium demand has grown, noting a 600% increase in the economy and projected annual growth of +26%. Exponential growth in resources is projected, where econometric, R-multivariable and R-linear models estimate that Peru could supply 1.5% in 2025 and 3% in 2030 of global lithium. Estimated growth of 5–15% in socio-environmental conflicts is projected with the start of lithium exploitation (Peru – Puno). The global potential of lithium demonstrates exponential growth. Lithium reserves in Puno - Peru would rank 13th between 2025 and 2030. It is necessary to establish a clear regulatory framework to avoid excessive increase in socio-environmental conflicts.

Feb 1, 2024

By M. B. C. Brandt

Richter magnitudes for seismic events were calibrated for use as a Local magnitude scale in the West Rand (WR), Far West Rand (FWR), and Klerksdorp–Orkney–Stilfontein–Hartebeesfontein (KOSH) gold mining areas. Richter magnitudes are currently calculated from seismograms recorded by local surface cluster networks using tabulated calibration values for Southern California, published in 1958. The Richter (1958) model is incorrect for distances of less than 30 km and should be applied only to crustal earthquakes in regions with similar attenuation properties to those of Southern California. When compared to the South African National Seismograph Network (SANSN), the cluster networks, on average, overestimate seismic event magnitudes by approximately 0.1 of a magnitude unit. A calibrated Local magnitude scale was derived by means of a multiple regression analysis between the Local magnitudes reported by the SANSN and the largest zero-to-peak trace amplitudes measured on the cluster network horizontal seismograms, after modelling the attenuation of the seismic waves as these progress from the epicentre to the station position. Magnitudes reported by individual stations for the same event show a significant scatter around the average magnitude owing to the near-surface amplifications of the seismic waves at the recordings sites. Average magnitude should be estimated using as many magnitudes of individual stations as possible to ensure an accurate estimate. Larger event magnitudes should be compared with those recorded by the SANSN.

Nov 1, 2021

By Phil Wilkinson, Sam Whitaker

"The installation of large (XL) diameter monopiles offshore typically requires expensive and specialist plant, equipment and vessels. Due to the increasing size (weight, diameter and length) of the foundations, in order to mitigate installation risk, the use of large diameter drills is becoming an increasing requirement.Project developers often try to avoid drilling operations due to the time associated with the drilling process. This restricts projects in terms of location and it also overlooks the additional engineering benefits drilling can bring to monopile foundation design e.g. reduced foundation material and better fatigue design life.By comparing the lessons learned of three milestone overwater drilling projects; methods of maximising drill speed and decreasing drilling process time is established. Particular emphasis is put on pile internal relief drilling in a process known as Drive-Drill-Drive (DDD).The milestone overwater drilling projects are North Hoyle Offshore Wind Farm (OWF) (2003); Flamanville EPR cooling water outlet shaft (2008); and Gwynt-y-Mor OWF (2014).By evaluating the effect of foundation pile diameter on drilling process times, example foundation installation costs are derived and used to show that incorporating drilling as part of a process may not be cost prohibitive to projectsContinued advances in drill technology, and drilling rates of penetration, combined with an integrated approach to foundation design, challenge whether hammering only is always the optimal solution for XL monopile installation."

Jan 1, 2017

By Leonardo Gonçalves Pedroti, Fernando de Paula Cardoso, Beatryz Cardoso Mendes, Afonso Ramos Garcez de Azevedo

This work aims to produce paints using granite waste, as a pigment, and compare their performance to soil pigments based paints, in terms of hiding power and abrasion resistance. Initially, the residue and soils were physically, mineralogically and morphologically characterized. For the production of the paint samples, an experimental model was defined, based on the variation of the proportions of pigment and resin. The proportion of water varied in each sample, in order to maintain the viscosity within a range considered ideal for application. Sequentially, tests were done to determine the hiding power and abrasion resistance of inks. It was found that, in comparison to soil paints, the granite residue paints presented greater hiding power. This result can be explained by the characteristics of the granite residue, which allowed a high nonvolatile content in the mixtures. With respect to abrasion resistance, granite residue paints showed less resistance than soil paints, possibly due to the granulometry of the residue that resulted in a greater roughness of film. In addition, none ink sample satisfied the minimum specifications prescribed in the Brazilian standards for hiding power and abrasion resistance, at the same time. This means that these inks, when used, will require more repair and repainting over time than conventional paints.

Mar 1, 2018

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining I research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and, the results are described in this report.

Jan 1, 1983

By J. W. Thompson

Be if enacted by the Senate and House of Representatives of the United States of America in Congress assembled, That deposits of coal, phosphate, sodium, oil, oil shale, or gas, and lands containing such deposits owned by the United States, including those in national forests, but excluding lands acquired under the Act known as the Appalachian Forest Act, approved March 1, 1911 (Thirty-sixth Statutes, page 9G1), and those in national parks, and in lands Withdrawn or reserved for military or naval uses or purposes, except as heroinafter provided, shall be subject to disposition in the form and manner provided by this Act to citizens of the United States, or to any association of such persons, or to any corporation organized under the laws of the United States, or of ;iny State or Territory thereof, and in the case of coal, oil, oil shale, or gas, to municipalities: Provided, That the United States reserves the right to extract helium from all gas produced from lands permitted, leased, or other- wise granted under the provisions of this Act, under such rules and regulations as shall be prescribed by the Secretary of the Interior: Provided further, That in the extraction of helium from gas produced from such lands, it shall be so extracted as to cause no substantial delay in the delivery of gas produced from the well to the purchaser thereof: And provided further, That citizens of another country, the laws, customs, or regulations of which, deny similar or like privileges to citizens or corporations of this country, shall not by stock ownership, stock holding, or stock control, own any interest in any lease acquired under the provisions of this Act.

Jan 1, 1921

By G. Lipsett, S. Dessureault

Information technology (IT) initiatives in the past have tended to be sold on their ability to maximize resource output and return on capital by allowing assets to be used more effectively and efficiently. Many IT projects fail, not delivering return on their investment. This is known in the IT industry as the “productivity paradox,” where increasing investments in IT do not result in comparable increases in productivity. Experiences and studies of most business sectors reveal that this paradox is rooted in the false assumption that more IT spending automatically results in financial benefit, whereas the benefits are in how effectively IT is used. Most business sectors have accepted that re-engineering of processes is required to gain the full benefits promised of IT. A mining operation has organizational processes similar to most business sectors, but unique operational processes. The lessons of changing business practice in more common business processes, such as inventory control and customer-supplier relationships, can be adequately transposed into a mine setting. The unique operational processes in mines, in turn, require unique redesign efforts. Several enabling information technology opportunities have recently become available, such as more integrated mine production management systems and tactical manager training simulators. This paper reviews some of the latest IT products and outlines the processes and kinds of change that will be required in order to benefit from these new investment options.

Jan 1, 2009

By S. C. Chelgani

The Thor lake deposit is a world class resource of rare earth (REE) metals and minerals in Canada. Development work to optimize a REE mineral recovery process flow sheet is underway, however, given the ore mineralogy; the developed reagent scheme is relatively complex. As part of a research project, micro flotation tests were conducted on a feed sample in order to examine factors affecting stream partitioning. SEM-EDX was performed to evaluate variability in grain composition between streams (concentrate and tails) and TOF-SIMS surface analysis was used to determine statistically significant differences in surface species particularly related to potential activation (or depression) of the examined mineral phases. SEM-EDX analysis reveal that the concentrate has a significantly higher proportion of REE bearing grains (carbonates and phosphates) relative to the tail (almost none were identified). Spectral fingerprinting by TOF-SIMS has allowed for the identification of all reagent species investigated. Reagent signal intensity discrimination on test stream mineral surfaces was observed by the TOF-SIMS analysis using reagents at plant concentration levels. TOF-SIMS analysis confirmed that REE bearing grains reporting to the concentrate are doing so in response to collector attachment whereas grains reporting to the tail are doing so in response to a lack of collector and/or in combination with the presence of the depressant. The surface analysis of gangue phases reveal a similar reagent discrimination; the signal intensity of collector species was significantly higher on the concentrate samples relative to the tails while depressant species were significantly enriched on the surface of the gangue phases in the tail samples. A detailed evaluation of the surface species representing the various reagents used in flotation scheme revealed a distinct competitive relationship between two of the reagents. The surface analysis identified that when used in concurrently, there appears to be a negative feedback resulting in a significant reduction in loading for several of the collectors on grains reporting to the concentrate. An evaluation of the effect of reagents on REE mineral in pilot plant is currently under way. Key words: Rare earth minerals, Flotation, Surface chemistry, TOF-SIMS, SEM-EDX

Feb 27, 2013

By Gerald H. Luttrell, Mohammad Rezaee, Roe-Hoan Yoon, Rick Q. Honaker, Aaron Noble, Abhijit Bhagavatula, Michael J. Kiser

A field study was undertaken to experimentally measure the concentrations of rare earth elements (REEs) contained in the process streams generated by a group of 20 coal preparation plants located in the eastern USA. For each site, representative samples of clean coal product, coarse refuse, and fine refuse were collected. Each sample was then partitioned into preselected size and density classes by wet screening/sieving and float-sink testing. The resultant products were dried and subjected to laboratory analyses to determine ash contents and rare earth element concentrations including Yttrium and Scandium. A detailed analysis of the database generated by this exercise showed that coal-based products from these preparation plants contained significant quantities of rare earth elements. In particular, the coarse refuse streams currently discarded by the 20 plants examined were found to contain a sufficient tonnage of REEs to satisfy the current domestic demand for these important elements. The data also showed a strong positive correlation between ash content and REE concentration, which suggested that the primary association of REEs in eastern USA bituminous coal sources is likely within fractions containing inorganic impurities. This association was well described using a simple power equation relating ash content and REE concentration. The ratio of heavy-to-light rare earth elements was discovered to be significantly higher in organically rich fractions of clean coal, suggesting that mineral impurities intimately associated with carbonaceous matter have elevated concentrations of heavy rare earth elements. A similar trend was observed for a grouping of rare earth elements (Y, Nd, Eu, Tb, and Dy) that are likely subject to near-term supply shortages. Finally, the database showed that a linear correlation existed between La for many REEs of interest, although there were several notable exceptions for some high-value REEs (Lu, Pr, and Tb).

By S. W. Jacobsz, F. O. Abimaje

Internal stability is a key consideration in the design and long-term performance of granular filters, as it precludes particle migration and internal erosion. This study evaluates the internal stability of coal discard material in coal co-disposal facilities. Reusing coal discards could reduce mine waste volumes and mitigate associated environmental impacts. However, coal discard material differs from most soils in terms of particle strength and density, with possible implications for hydraulic stability. Laboratory seepage tests were conducted on coal discard material under varying void ratios, subjected to a range of hydraulic gradients, and the results were used to confirm the applicability of the widely used empirical Kenney and Lau filter criterion to coal discard. Findings revealed that particle loss increased with higher void ratios. Nonetheless, particle migration remained minimal, with a maximum particle loss of only 0.2%, suggesting that coal discard exhibits sound internal stability under the tested conditions.

Jul 3, 2026

By M Henderson, M Hudyma

Mining-induced seismicity at Junction Gold Mine became a serious operational problem in the late-1990s. Assessing the local seismic hazard is an important step in assessing the risk associated with potential rockbursting. This paper discusses the qualitative and quantitative means of assessing seismic hazard used at Junction. In qualitative hazard assessment, the role of the primary factors contributing to mining-induced seismicity and rockbursting are identified. These factors include: rock mass properties, geological structures, mine development, and stoping. A qualitative seismic hazard map has been developed considering these factors. In quantitative hazard assessment, seismic source parameters from an Integrated Seismic System are used to assess seismic hazard. The seismic source parameters found to be relevant to seismic hazard assessment at Junction are discussed.

Jan 1, 2002

By Paikowsky, Samuel G.

"Due to the way drilled deep foundations are being constructed, their structural integrity and geotechnical capacity are highly variable. Drop weight systems are increasingly being used to dynamically test the capacity and integrity of drilled deep foundations. Conventional pile driving hammers are often either inadequate or not economical to test these foundations and drop weight systems have therefore been developed to allow for dynamic testing.The advantages of the tests include high mobility, short testing time, low cost relative to static load tests (allowing multiple tests at a single site), and integrity/construction quality evaluation concurrent with capacity determination. The dynamic testing method for drilled deep foundations encounter several difficulties including: the need for a pre-testing analysis for matching pile, soil and testing system, adequate mass and drop height to reflect the mobilized capacity without structural damage, test interpretations for irregularly shaped and/or non-uniform piles, need for reliable dynamic measurements depending on the impact and the distance between the impact and the measuring point, and limited knowledge about the accuracy of the predictions.The principles of the tests are presented using simplified models and demonstrated via a case history. Drop weight systems are reviewed. Dynamic measurement principles are explained and the construction and testing quality effects are outlined and demonstrated via numerical modeling and case histories. A comparison of dynamic and static tests is presented via a database, case histories and finally a short review of relevant codes is provided.1 IntroductionTraditional static axial load test is performed by a slow application of a force produced against independent reaction, imitating structural loading. It is the most reliable method to determine the pile’s performance as commonly required under typical service conditions. The major limitations of this testing are: (i) high cost associated with set-up, test duration, interpretation and construction delays, and (ii) inability to obtain information about the pile-soil interaction along the pile without additional testing means (e.g. tell tales, strain gauges, etc.). These limitations are acute when high capacity foundations are involved."

Jan 1, 2015

By H Bateman, I Cawrse, G Carnes, S Cawrse

In developing mineral resources, the focus typically centres on the management of identified social and environmental impacts and compliance with regulatory requirements. However, opportunities to protect and enhance the environment and communities are most effective in the planning and design phases. Achieving the objective of integrating sustainability considerations as an element of design decision making requires that the design criteria be technically sound, relevant to the project and applicable to desired design outcomes. This is particularly important for projects employing virtual teaming, where design engineers may be geographically dispersed and are unlikely to be familiar with site specific sustainability challenges and opportunities. This paper documents the approach taken by BHP Billiton to incorporate sustainability principles, objectives and guidelines in design criteria for the Olympic Dam Expansion (ODX) project. It describes the range of inputs used in defining sustainability objectives which interface in a framework that is dynamic and transferable to other mining projects and to engineering design in general. The Sustainability in Design Criteria document distils statutory requirements, corporate standards, lessons learned and leading industry practice into a single coherent framework that supports engineers to approach problem solving as a holistic and integrated exercise with a long term perspective. The framework also serves to improve linkages between internal stakeholders by fostering greater communication, collaboration and innovation to deliver more sustainable outcomes through the design process.

Jan 1, 2009

Contract No. H0110929 was awarded by the U.S. Bureau of Mines in February, 1971, to DeTer Company, Incorporated, of Mountain Lakes, N. J. The contract provided for the modification of the contractor's Model 5000 Pressure Foam Generator to fit it for the suppression of coal dust in mines, a detailed testing program in a working coal mine, and for additional modifications and testing for the suppression of fires in coal mines. The contractual program was completed in April, 1972. The results of the dust suppression tests showed conclusively that the modified DeTer equipment effectively reduced the level of respirable dust in a working coal mine well below the present and future acceptable levels set by the Mine Health and Safety Act of 1969. The fire tests, carried out in a simulated mine entryway erected on the surface, demonstrated the ability of the DeTer equipment in suppressing fires of varying degrees of severity within an acceptably short time.

Jan 1, 1972