Search Documents

By J. J. McDougall

Until quite recently, the coal in the Cape Breton field was won from comparatively thick seams with light cover, and from submarine areas, and the system of mining naturally followed was pillar-and-stall. This sytem permitted of cheap extraction, and enabled production from localities where other methods could not be employed to good advantage. Thus the pillar-and-stall system, applied to conditions as stated, justified its adoption. Our working seams today, however, are practically all under heavy cover, or are moving in that direction, and with this gradual increase in cover came the increased cost of roadway maintenance. At Princess colliery, the system of pillar-and-stall was followed until roof and bottom conditions became such that further operations were unprofitable, and the longwall method was then adopted as an economic necessity. This fact should be borne in mind when operating costs of both systems are being compared. The longwall method is not held as a cure for all difficulties of heavy cover, but through it these difficulties can be overcome with less expense than by pillar-and-stall. The longwall system of mining, strictly speaking, is one by which a seam of coal is totally extracted in one operation. There are, however, many modifications of longwall, and in some cases it is difficult to determine whether certain practices should be classed as longwall or pillar-and-stall, or a combination of both.

Jan 1, 1928

By H. B. Hill

The Lake Creek gas-condensate field, Montgomery County, Tex., Was discovered early in 1941 by the Superior Oil Co. The field, shown in figure 1, is approximately 37 miles northwest of Houston, Tex., about 11 miles north of the Tomball, and 10 miles west of the Conroe oil fields. The field is on the downthrown side of a pronounced fault zone, and the general structure is anticlinal, with the long axis trending northeast and southwest. Production is obtained from multiple sandstone reservoirs in the Wilcox group of Eocene age between the approximate depths of 8,820 and 11,840 feet below the surface of the ground.

Jan 1, 1948

By K. Papke

Nine western states contain significant barite deposits, but most deposits are in Nevada, which has been the principal western producer for more than three decades. Nevada produces about 85% of the total United States production, but about one-half of the barite consumed in the country is imported. Approximately 95% of the barite is used in drilling muds. Sharply decreased oil and gas drilling, starting in early 1982, severely depressed the domestic barite industry. Other problems for western barite include long distances to the areas of major drilling, high railroad-freight rates, and increased barite imports. Bedded deposits, formed by submarine exhalative processes, account for almost all western production, and reserves are large.

Jan 1, 1983

By Venda Oliveira P. J., Correia A. A. S., Danisi C. M.

"AbstractA laboratory study has been undertaken to establish common understanding of the creep phenomenon of a Portuguese soft soil chemically stabilised with binders. In order to study the effect of different stress levels on the strength and on the creep behavior of the stabilised soil, oedometer creep tests and unconfined compressive tests were performed at different curing times. Results show that the creep stress level does not influence the unconfined compressive strength. In addition, the creep phenomenon increases the unconfined compressive strength of the treated soil. Two different secondary compression indexes were recognized from the one-dimensional compression curve which increase with an exponential trend with the creep stress level.IntroductionConstruction on soft soils requires a mandatory soil stabilization work to improve mechanical characteristics of the natural soil. Deep mixing method is a worldwide employed ground improvement method, nevertheless the creep phenomenon hasn’t been yet thoroughly analyzed. Most of the published papers have focused on the analysis of the compressibility and the strength of the soil-binder mixtures without considering the creep phenomenon. However, numerical results (Venda Oliveira et al. 2009) have shown that although settlements that occur during the creep stage (namely creep strains) are less in case of treated columns, they are still important especially due to the high loads applied to the stabilised soil. The few published studies about creep behavior of soil-binder mixtures reveal that the stabilization of an organic soil with cement induces a reduction of creep deformations, which is related to the amount of cement used and that the increase of the organic matter of the soil has a negative impact on soil stabilization, further inducing a slight increase in the creep deformations (Venda Oliveira et al. 2012).As part of the current research the effect of different stress levels on the creep behavior of a soft clayey-silt soil was studied. The binder mixture used to enhance the properties of the soil had a specific composition and quantity. Unconfined compressive strength tests (UCS) and UCS creep tests were carried out at pre-set curing times in order to analyze the creep behavior of the soil-binder mixture. In particular five different creep stress levels were studied to understand its influence on the strength and on the compressibility of the stabilised soil. In addition, considerations about the secondary consolidation index are also presented."

Jan 1, 2014

By A. MacRae

Campaign life of the converting furnace has been limited by break-outs through the hearth and walls. Throughput of concentrate has increased by 60% since start-up of the copper operations in 1981. The Furnace Integrity program was initiated at Kidd in 1993 to improve the reliability and safety of the smelting-cleaning-converting furnace line. The converting furnace is undergoing a series of upgrades to overcome severe refractory wear to the roof, walls and hearth. A recent shut-down was held in March 1997 to implement improvements to the roof, walls and slag outlet. Wall modifications included a new upper shell, wall coolers which can be supported during a shut-down from outside of the vessel, and an increase in the number of cooling blocks. Improvements to the roof included increased cooling, a novel brick/cooler suspension system, and roof compression for gas tightness. Design is currently underway to deepen the refractory hearth, to decrease hearth erosion and increase resistance to flotation.

Jan 1, 1998

By R. W. Stahl

Gas accumulation and dust suspension are the major safety hazards in coal stockpiling and reclaiming operations. This report presents a schedule of safety precautions and plant design features devised by the Bureau of Mines to reduce danger from these and other sources.

Jan 1, 1965

By A. F. Henderson, C. F. Cornell, A. F. Dunyon, D. A. Dahlstrom

IN processing magnetic taconites several steps of crushing, grinding, classification, and magnetic separation are required to produce a 60' pct Fe concentrate. Usually the final concentrate is in a slurry form of 55 to 70 pct solids by weight and is further characterized by a particle size of 60+ pct —325 mesh. In taconite plants already completed or under construction the conventional method used to obtain pellets suitable for blast furnaces is to filter the concentrate slurry, ball the filter cake, and then harden the green pellets in a traveling grate or in a vertical shaft furnace. Large tonnages must be handled in minimum floor space, with reduced maintenance and lowest possible operating cost. Filtration must therefore achieve two objectives: I) high filtration rate—in terms of pounds of dry solids per hour per square foot of filtration area—at a low filtrate solids concentration, and 2) a filter cake moisture that will always permit efficient balling within the normal fluctuations of ' plant operating conditions. If moisture contents are too high, balling may be impossible or result in a mushy ball .without enough green strength for the firing operation. Development work has met these objectives. At low investment and operating costs, filtration rates of 250 to 600 dry lb per hr per ft2 have been attained for concentrates of 60' pct —325 mesh. By combining the disk-type continuous filter with proper agitation, the Agidisc filter produces a homogeneous filter cake, easily discharged from the disk sectors. This application provides the lowest initial cost per square foot of filtration area, minimizes floor space, reduces down time for changing filter media to a negligible factor, and simplifies process control and maintenance for the operator. It is now possible to predict very closely the taconite concentrate filtration rates for a wide variety of conditions—either by experience or with a few simple leaf tests. When balling and pelletizing operations began on a continuous basis, it became apparent that moisture content of the filter cake was a critical factor and must always be controlled by the filter operator below some maximum allowable value. Accordingly the Reserve Mining Co. and the Eimco Corp. joined in a study of the many variables affecting filter cake moisture content. The study was conducted at the Reserve Mining Co. taconite plant at Babbitt, Minn. To process plant tonnage the Babbitt plant utilizes a 6-ft diam Agidisc filter with six disks and an 8-ft diam drum filter with 10-ft face. However, most of the plant filter investigations were made on the Agidisc because of its superior performance. A considerable amount of small-scale test work was first carried out to study more closely the individual variables and ascertain their effect on filter cake moisture content. A general correlation method was then developed which allowed reasonable prediction of moisture content at any operating conditions. This step was made necessary by the fact that in full-scale filtering, operating variables usually interact to produce a combined rather than a singular effect. Studies were then made on the full-scale filters to prove the validity of the correlations developed, and past operating records were examined to ascertain whether or not significant variations could be traced to any single factor or to a combination of factors.

Jan 1, 1958

By Paul H. Mutschler

The Bureau of Mines sponsored a study of the impact of changing technology on the demand for metallurgical coal and coke to 1985. Individual technologies were analyzed to determine what effect each had on the demand for and the consequent consumption of metallurgical coal and coke in the steel industry. The domestic steel industry demand for metallurgical coal and coke for the production of hot metal will probably increase through 1985. Formcoke if implemented on a worldwide basis could begin to supplant the U.S. export market for metallurgical coal. The major technologies that have contributed to the decline in demand for metallurgical coke per ton of hot metal are (1) the increased usage coupled with higher iron content of agglomerates, (2) modification of blast furnace practices such as high top pressures and blast temperatures, and (3) increases in the injection of supplemental fuels. The projected demand for metallurgical coal and coke under current technology for 1985 are 109.4 and 76.0 million tons, respectively. With future technology implemented, the demand for metallurgical coal and coke will be 82.0 and 56.9 million tons, respectively. The projected domestic demand for metallurgical coke could further decrease by as much as 15 to 20 million tons by 1985 if formcoking proves technologically and economically feasible.

Jan 1, 1975

By George L. Gates

This report presents is an evaluation by the Federal Bureau of Mines of the effect of clay-water, brine, and oil-base drilling fluids on the productivity of test wells drilled on the Umiat anticline in U.S. Naval Petroleum Reserve No. 4 in northern Alaska. Eleven, wells were drilled on the Umiat structure as part of the U.S. Navy's extensive exploration of the Reserve during 1944-53 to determine the possibilities for oil production. The Federal Geological Survey cooperated in the exploration program and has published a comprehensive report3/ on the geology of the area and case histories of the wells. The re¬port also includes the results of special studies by the Bureau in connection with the drilling and coring of well 9 with oil-base mud in hole and was the source of much of the information used in preparing this publication. Of the eleven wells, four were drilled with rotary tools and water-base mud (one of the water-base muds was an oil-in-water emulsion mud), five were drilled with cable tools with brine in the hole, one was drilled with cable tools with brine in the hole and later reamed with rotary tools and crude oil, and one was drilled with rotary tools and oil-base mud. Although all of the wells penetrated sandstones that contained oil and gas, some were productive and others were not. The latter two wells, one completed with crude oil in the hole (with some added brine) and the other with oil-base mud, had the greatest productive capacities. The wells drilled with cable tools and brine in the hole had lower productive capacities. In contrast, two of three wells completed with rotary methods and fresh-water drilling mud and the well com¬pleted with rotary and emulsion mud were unproductive.

Jan 1, 1960

By Christopher Mark

Pillar recovery continues to be one of the more hazardous activities in underground coal mining. Safety requires that the roof above the intersection remain stable until after the pillar has been extracted. Artificial supports (timbers and Mobile Roof Supports) arc essential to roof stability, but so is the final remnant stump or pushout. Traditional mining practices usually called for the complete extraction of the final stump, but the recent trend (both in the U.S. and internationally) seems to be towards mining plans that leave a remnant stump. For this study, a sample of roof control plans from the Mine Health and Safety Administration (MSHA) Coal Districts were analyzed to determine current pillar recovery practices. Both full- and partial- extraction plans were included. Special attention was paid to whether plans require that a final stump be left, and whether requirements regarding the dimensions of the remnant stump are included. Foreign experience with final stumps is also summarized. It seems that the risk of major pillar falls can often be reduced by leaving final stumps that are large enough to protect the intersection, but small enough that they do not inhibit the caving of the gob. Because final stumps are often irregular in shape, a new approach for estimating their strength is described. Analyses were conducted to assess the effect of seam height and depth of cover on the potential variation in the size of remnant stumps.

Jan 1, 2001

The works of Metal Manufactures Ltd are situated at Port Kemblam NSW, within a few hundred yards of a deep-water harbour. At present they occupy about 26 acres, and ample provision has been made for future extensions. Rail connection exists between various parts of the Works and the main South Coast Railway, the harbour jetties and the adjacent copper refinery of The Electrolytic Refining and Smelting Co Ltd. A plan of the works is shown in Fig 1.The company was incorporated in March 1916, and commenced production of copper wire in June 1918. Early in 1920, tube manufacture was undertaken, followed by telephone cable mnufacture in 1923. Today the Works consist of five principal sections: Founrdy, Tube Factory, Wire Factory, Cable Factory and Case and Drum Factory. Whilst the last four are engaged in producing the finished materials for despatch from the Works, the first-mentioned is engaged in producing copper, brass, and other non-ferrous billets for use in the Tube and Wire factories. In addition, there are Engineering and Metallurgical Departments supporting the manufacturing sections, and in these, as well as in all other sections of the Works, extensions have been carried out from time to time to provide for increased output and new types of products.

Jan 1, 1938

By P. L. Weston

The Bureau of Mines used high-temperature reduction roasting, magnetic separation, acid-leaching, and autoclave precipitation processes to recover iron and manganese from brown Cuyana range ores of Minnesota. Wet magnetic separation concentrated over 90 percent of the iron in 3 of 4 ores as high grade products analyzing 74 to 85 percent iron, 2.5 to 6 percent manganese, and 3 to 10 percent SiO2. The nonmagnetic fractions were leached with dilute sulfuric acid extracting 83 to 93 percent of the contained manganese and small amounts of iron. The leach solutions contained Mn-to-Fe and Mn-to-SiO2 ratios favorable enough for possible consumption in metallurgical mane operations. Exceptionally pure Mn solutions were achieved by pressure precipitation of the remaining iron in an autoclave followed by lime precipitation of silica and alumina.

Jan 1, 1966

Adverse ground behavior events, such as convergence and falls of ground, are some of the most significant challenges and hazards in underground mines. Our goal is to work toward mine-wide, digital, and real-time three-dimensional geotechnical situational awareness and predictive capabilities in complex underground mining operations. This will benefit operators, engineers, and management by enabling them to develop a more proactive approach to ground control. To this end, and inspired by research in the field of remote sensing and autonomous robotics, this paper assesses the potential of mobile light detection and ranging (LiDAR) data acquisition for high-frequency, high-accuracy monitoring tasks in Global Navigation Satellite Systems (GNSS) deprived underground mines. Limitations of current monitoring practices are reviewed. Relevant academic and commercial developments in the fields of indoor mobile mapping systems (MMSs) and simultaneous localization and mapping (SLAM), robust autonomous robotic platforms, and automated remote sensing data processing are highlighted, and their current shortfalls are evaluated. To conclude, the ramifications of this work for the development of future autonomous underground mine monitoring solutions are discussed.

Jul 28, 2020

By PC Pistorius, DR Groot

The South African base metals industry has been one mainly focused on the production of metals or metal compounds from primary ores. This is true for metals such as titanium, vanadium, chrome, manganese, cobalt, nickel, copper, zinc and aluminium. The steel making industry has traditionally used a substantial portion of scrap steel, and could thus be considered to be somewhat of an exception. Secondary sources have played much less of a role, possibly due to at least some of the following factors. Scrap material is often of unknown composition, and thus it requires additional chemical analysis, and possibly special treatment. Tonnages are relatively small, and the incorporation of secondary materials is possibly seen to carry undue risk and inadequate benefit. South African consumers are still not very conservation and recycling conscious, which limits the amount of scrap made available. This attitude might also be expected to influence decision makers in these industries. Finally, pressure from environmentally motivated activists locally has not been unduly large. This landscape has been changing, and is continuing to do so. Various municipal authorities such as those of Pretoria, Johannesburg and Cape Town are reporting increasingly limited landspace for waste (Bondolfi, 2007). There are increasing concerns regarding the leaching of hazardous metals such as chromium, mercury and cadmium from landfill waste, especially electronic and electric wastes ? the so-called eWastes. In more developed countries such as the United States of America and Western Europe the problem of eWaste has grown to the extent where legislation has been enacted, such as the Waste Electrical and Electronic Equipment (WEEE) legislation of the EU (European Union Directive 2002/96/EC). The 19th and 20th centuries have seen major technological advances. Relevant to this paper is the availability of centrally generated electrical power, telecommunication, entertainment through recorded and transmitted music and images, the growth and pervasive influence of electronics, and the handling of digital data by computers and microprocessors. These developments have placed ever increasing demands on resources for the manufacture of electrical and electronic equipment, as well as on the generation of electrical power. Most of the resources required are non-renewable: copper, steel, aluminium and other metals, various thermoplastic polymers such as PVC (polyvinyl chloride), polyethylene and ABS ( acrylonitrile-butadiene-styrene), thermosetting polymers such as epoxies, elastomers such as butyl rubber, glasses and ceramics, and composites such as fibre reinforced plastic (fibreglass). The conservation of non-renewable resources inevitably includes recycling. To a certain extent, recycling of materials locally is well established. Thus glass, paper, used oil, car batteries, ferrous scrap such as beverage cans and non-ferrous scrap such as

Jan 1, 2007

By G. Haesebroek

In L969 Metallurgie Hoboken-Overpelt started an industrial plant for the separation of iron and zinc from a concentrated CoCL2 solution. Iron and zinc are extracted in column contactors by a solvent containing 12 vol % of tertiary amines in xylene. The extracted metals are stripped from the pregnant organic phase by precipitation with a NaOH solution at pH LL. In this paper an overview is given of the industrial process. In order to overcome some drawbacks of this process (low flash point of the diluent, reagent consumption, batchwise stripping) an alternative solvent extraction process has been examined. In this alternative process, iron and zinc are extracted with an or¬ganic phase containing 50 vol % of TBP in Escaid 110. The pregnant solvent is stripped with water in conventional mixer settlers. Despite the ability of this process to overcome most of the inconveniences due to the use of tertiary amines, it suffers from the poor stability of TBP in concentrated chloride solutions, resulting in unavoidable and inacceptable precipitation phenomena in the stripping section.

Jan 1, 1988

By E. H. Henderson

Introduction Stamp-Milling and amalgamation is, perhaps, one of the oldest processes of recovering gold from its ores. Many papers, theses, and textbooks have been written on the subject of stamp-milling practice in general, but, to my knowledge, there have been no publications describing the modern stamp-mill as designed, developed, and operated in Nova Scotia. Although it may be said that the gravity stamp-mill is the most primitive, and perhaps the crudest, crushing machine in existence, it is at the same time the most satisfactory all-round milling and amalgamating device yet contrived. Originating in Saxony, and used in North America first in Virginia and Georgia, the stamp-mill, in a primitive form, later found its way to California and Colorado. Here, it speedily developed from an affair of wood shod with iron, and operated with the crudest gearing, to substantially its present form. Briefly, it consists (see Figure 1) essentially of a series of hammers (the stamps), which fall upon a mixture of ore and water contained in a cast-iron box (the mortar). The resulting crushed ore (the pulp) is splashed out through a screen on the front of the box. For some years after the discovery of gold in Nova Scotia, in 1861, the ? arrastra and Chilean mill were used to recover the gold from the rich ores. The stamp-mill followed, and various types were used, principally the California and Gilpin County types. Then, in 1895, Mr. M. R. O'Shaughnessy, one of our foremost amalgamators, conceived the idea of a new type of stampmill, which has since become standard in Nova Scotia gold mines. This mill, unique in its design and operation, is specially adapted for the most efficient extraction and recovery of gold as it occurs in our Nova Scotian ores. It is commonly known as the Underwater Feed type, as opposed to the usual Overwater or Top Feed type, and it may be rightly termed The Nova Scotia Self-Classifying Stamp Amalgamation Mill. It is conceded by experienced mill-men that it is superior to any other type of mill for recovering the very coarse and granular gold typical of the ores of this Province. The particular installation and practice to be described in this paper is that of the Guysborough Mines, Limited, at Goldenville, Guysborough county. Emphasis will be laid on certain operating innovations of extreme simplicity and high efficiency.

Jan 1, 1935

By Ettore Contestabile, Cameron Thomas

Implosive connectors such as XECONEXTn have been used extensively for joining electrical conductors. This implosive action of explosives has also been used in other forms of high-energy metal working with excellent results. However, the inherent blast energy of these units can cause environmental side effects (especially airblast) which may restrict their use around inhabited areas.

Jan 1, 1994

By P. E. Cavanagh

FOR THE PAST seven years Mr. W. Simpson, Chief Mechanical Inspector for the Nova Scotia Department of Mines, has carried out exhaustive field trials of non-destructive inspection equipment in the coal mines of that Province. This work has demonstrated the usefulness of a number of types of non-destructive inspection when used for periodic inspection of hoisting and haulage equipment in the coal mines of Nova Scotia. As a result, the Dominion Coal Company has instituted a programme of regular preventive maintenance inspection ?by a special staff of qualified and trained men. The purpose of this present paper is to describe how non-destructive testing techniques are used on ropes, axles, couplings, and other hoisting and haulage equipment, how these methods are being used in other industries, and the expected benefits from intelligent and properly organized use of these techniques in the coal mining industry.

Jan 1, 1956

By Juver Vélez

Este método de exploración consiste en la introducción con un equipo mecánico - hidráulico que ejerce presión y rotación sobre un tubo de metal el cual tiene en su inicio una corona con diamantes impregnados (denominada broca), al interior de la corteza terrestre, con el objetivo de extraer el material roca de profundidades a la superficie para realizar su identificación geológica y análisis varios; La perforación diamantina ha venido desarrollándose a través del tiempo y con la experiencia de los operadores, llegando a crear máquinas de gran capacidad para alcanzar grandes longitudes.

Sep 1, 2017

By J. H. E. Jeffes, C. Diaz

The heat balance and chemical equilibria involved in the production of blister copper from a chalcopyrite concentrate in a single operation are examined. It appears that two stages—one oxidising and one reducing—will be required. The analysis indicates that on thermal grounds the process is possible with a dry, high-grade chalcopyrite concentrate, if oxygen enrichment to about 30 per cent is used, but that copper losses in the slag will be serious and will require a secondary recovery operation. More extensive data on the activities of copper oxide in slags are required to elucidate this point more effectively

Dec 1, 1971