Search Documents

By M. A. Trevits, A. Ozment

"According to the Office of Surface Mining Reclamation and Enforcement, Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires in nine states. This is considered to be an underestimate for the actual number of fires nationwide. Many mine fires are started by people burning trash where the coal seam or an abandoned coal mine is close to the surface. Other fire ignition sources include lightning and forest fires. Once ignited, a coal mine fire can easily spread into the remaining coal pillars and mine entries. Once established, the fire creates its own ventilation system supporting further combustion by drawing air down into the workings through unsealed mine shafts, fractures and surface subsidence depressions. As the coal left in the workings from the past mining operations burns, the mine void can collapse, causing subsidence and creating dangerous voids, damaging overlying surface structures and roadways. The products of combustion include smoke and noxious fumes such as carbon monoxide gas. These products are released to the atmosphere through fractures that develop within the ground surface, killing vegetation and creating serious health hazards (Richmond, 2017).Abandoned mine fires, if left uncontrolled, can burn for years and, in fact, one of the most wellknown mine fires in the United States is the mine fire in the Borough of Centralia, PA, that began on May 27, 1962. Reportedly, officials decided to clean up the local landfill for the upcoming Memorial Day holiday by burning the garbage on the site. Unfortunately, the landfill was located on the site of an abandoned strip-pit mine on the edge of the Borough (Dekok, 2009). The strip pit had been left open after being excavated around 1935 and was approximately 23 m (75 ft) wide and 15 m (50 ft) deep. It is believed that the lack of a properly constructed noncombustible shale barrier in the strip pit enabled the fire to spread to adjacent carbonaceous refuse material and then to nearby coal mine workings (PA DEP, 2017). As time went on, the fire grew and spread under the Borough and directly affected the residents despite various efforts to extinguish the fire by the state and federal governments (Fig.1). In 1984, a voluntary program was begun to move residents from their homes. Many accepted buyout offers for their properties and moved elsewhere and after leaving, their homes were demolished. In 1992, the state used eminent domain to take control of all the property within the Borough. In 2013, after years of litigation, the eight remaining residents were allowed to stay for as long as they lived. Today, only a few buildings remain within the Borough (Centralia, PA, 2014). This fire has been burning for more than 55 years."

Jan 5, 2018

By Doug Harding

The Metropolitan St. Louis Water District’s Project Clear is a 28-year program targeting wastewater capacity throughout St. Louis, MO. The extensive program includes the Jefferson Barracks Tunnel, running parallel to the Mississippi River at 2 m ID and 5,400 m long. A rebuilt Robbins Main Beam TBM began boring but hit challenging conditions about 2,400 m in, including water inflows. A larger 4.1 m Robbins Main Beam machine will complete the remaining 3,050 m in limestone, dolomite, and shale. The TBM will utilize a high-powered, high breakout torque cutterhead along with enhanced 360-degree probing & grouting capabilities to detect any karst formations.

Dec 1, 2022

By T Baumgartl, D Mulligan, R Haymont

Mining at the Mt Leyshon Gold Mine in semi-arid north Queensland stopped in 2002. Newmont Australia has recently initiated a thorough post-closure water management study of the site by revisiting the existing information and conducting new water-related investigations. The focus of this paper, which is the first publication on post-closure environmental management of the site, is an overview of the site water quality in view of the sources and spatial distribution of polluted mine water, and also the performance of cover systems in controlling water flux though mine wastes. Since the mine closed the rehabilitation of waste rock dumps and tailings dams have significantly improved water quality in the surface receiving waters. However, the Scats Stockpile, the Heap Leach and Old Plant areas, which can potentially produce acidic waters, enriched with heavy metals and arsenic, are the top management priority. Modelling of the potential transport of contaminants in groundwater needs further investigations. A detailed examination of the waters in seepage sumps showed high concentrations of manganese, cobalt, nickel and selenium, which were previously overlooked. The study also showed distinctive chemical signatures for waters at different locations: the waters draining from scats, supergene materials and waste rocks have distinctly lower pH and higher concentrations of dissolved iron, sulfate, heavy metals, Mg, Mn, U, Se and As. While, the tailings sumps are more alkaline, and are enriched in Na and Cl. The southern tailing sump is characteristically As rich. The waters draining from the supergene materials have higher Cu concentrations. Assessment of the cover monitoring systems showed that although covers pass the design criteria, automated recording of data may ignore any failure of the monitoring system. Recalibration of the moisture sensors not only showed realistic moisture values compared to rainfall data but also showed that the permanently installed system records values that are higher than those of the mobile system. Event-driven recording of data overlooks infiltration events. Besides, with a higher time resolution (daily measurements) the breakthroughs could be clearly detected. Modelling of the water balance in covers is underway and an example is given here. Newmont is currently reviewing water management options and is willing to share the lessons learned.

Jan 1, 2006

By Greg Beckstrom

On Oct. 1-3, SME?s Twin Cities chapter (SME TC), in cooperation with the University of Minnesota ? Duluth?s Precambrian Research Center (UMD-PRC), cohosted a symposium on silica sand mining and processing. The conference was held at the Earle Brown Heritage Center near Minneapolis. The symposium was followed by a day-long field trip to operating mines, processing plants and loading facilities located in southwestern Wisconsin. Speakers and attendees at the symposium included university professors, industry experts, regulators, mining company representatives, equipment suppliers, consulting engineers and service companies. Approximately 320 people attended the conference. In addition, about 50 people who oppose mine development and the oil and gas industry showed up to voice their displeasure with the event and those companies that operate in this space.

Jan 1, 2012

By John D. Spencer

Research on the development of new and improved methods for the discovery and production of oil and gas and production of fluid fuels from coal continued to be the major thrust of the Bureau of Mines energy research program during 1973. Crude oil recovery from tar sands and oil shale also retained a high priority in this work. Complementing this program were numerous studies aimed at accomplishing the objective of increased energy output with greater safety and minimum harm to the natural environment. This report summarizes research objectives and results and itemizes formal publications of the Bureau of Mines on energy and related subjects.

Jan 1, 1974

By W. R. Hardwick

This paper describing the mining methods of the Inspiration Consolidated Copper Co. is one of a series being prepared by the Bureau of Mines on mining methods and costs in various mining districts of the United States. The story of mining at Inspiration is of particular interest because, after 127,812,000 tons of low-grade copper ore were successfully mined, the mining method was changed from block caving to open-pit. As the open pit became deeper, many features of the former block-caving operation that were exposed elucidated concepts of the mechanics of caving that previously had been assumed but not observed. The conversion to open-pit mining was accomplished by unique combinations of equipment and the introduction of ingenious engineering and operating practices that have extended the expected life of the mine for many years.

Jan 1, 1963

By W. R. Hardwick

This paper describing the mining methods of the Inspiration Consolidated Copper Co. is one of a series being prepared by the Bureau of Mines on mining methods and costs in various mining districts of the United States. The story of mining at Inspiration is of particular interest because, after 127,812,000 tons of low-grade copper ore were successfully mined, the mining method was changed from block caving to open-pit. As the open pit became deeper, many features of the former block-caving operation that were exposed elucidated concepts of the mechanics of caving that previously had been assumed but not observed. The conversion to open-pit mining was accomplished by unique combinations of equipment and the introduction of ingenious engineering and operating practices that have extended the expected life of the mine for many years.

Jan 1, 1963

By J. G. Bennett

Coal consumption has increased globally by 57% over the last ten years. Underground mining typically provides coal of the highest calorific value and accounts for the greatest proportion of production. Despite a negative environmental image and indeed impact, this industry appears likely to thrive on the global scale for many years to come. Such mining consumes large amounts of electricity with implications for carbon dioxide emission at power plants and emits substantial quantities of the powerful greenhouse gas methane. In response to this significant carbon footprint, the European Union has funded research to examine the potential for a range of improvement technologies in a project entitled Low Carbon Mine Site Energy Initiatives (LOWCARB). Coal properties related to seams and mines, together with longwall characteristics, provide the basis for research into modelling optimally efficient methane drainage with a view to assisting mining as well as maximising electricity generation at surface and hence oxidation of the methane. Possible systems for the oxidation of very low concentration methane in ventilation air, which contributes the greatest greenhouse gas impact due to the volumes emitted, have been studied and modelled. Simulation and investigation of intelligent optimisation of electricity demand patterns provide the basis for reducing the demand peaks at mines and hence the cost and ultimately the carbon footprint of a mine, while specific investigations have been undertaken into ventilation efficiency at an unusually challenging mine and simulation of mine water pumping in order to develop an innovative method to monitor pumping systems efficiency. For post-mining use, the potential of disused shafts for compressed air energy storage to improve the operation of future electricity grids with high renewable energy penetration by reducing peak generation capacity requirements has been studied. While underground coal mining will always by definition be related to a significant carbon footprint, this paper provides an overview of a set of initiatives that can make a positive environmental impact while controlling costs across a huge global industry.

Aug 1, 2013

By J. Chirasha

Keywords: Pyrometallurgy, ferrochrome, smelting, investment, Zimbabwe Four smelting plants currently make up the ferrochrome smelting capacity in Zimbabwe. Zimbabwe Alloys and Zimasco represent more then ninety per cent of Zimbabwe?s ferrochrome smelting capacity, while Maranatha and Oliken contribute the difference. Very limited investment in the sector (even for the expansion of existing smelters) has been experienced over many years, despite the fact that about 95% of the world?s chrome ore resources are in the Bushveld Igneous Complex of South Africa and the Great Dyke of Zimbabwe. The Bushveld has a greater quantity but a lower grade than the Great Dyke. A ten per cent increase in Zimbabwean ferrochromium production has been recorded in the past ten years, showing an almost stagnant capacity investment.

Jan 1, 2011

"10.1. IntroductionAs discussed by Westland (1981), the six platinum-group elements (PGE) belong to the Group VIII transition metals, to which iron, nickel and cobalt also belong. The chemical similarity between these nine metals accounts for the fact that they tend to be concentrated together as a result of geological processes. These processes started to effect the distribution of these metals at the very beginning of the earth's history.The first line in Table 1 gives the concentration of nickel and certain other Group VIII transition metals in carbonaceous chondrites, those meteorites with a composition that is believed to reflect best the composition of our planetary system apart from hydrogen and helium. The second line is the estimated concentration of the same elements in the earth as a whole. It is seen that these two estimates are quite similar, the earth being perhaps 2 to 3 times richer in these particular metals than the planetary system as a whole. The reason for this is not fully understood, but it may be due to the earth being formed by the accumulation and capture of a greater proportion of iron (and therefore siderophile-rich) than stoney (and therefore siderophile-poor) planetesimals than the planetary system itself.The third line in Table 1 is the average composition of the crust of the earth. With the exception of iron, all of the Group VIII transition elements are rare in the crust, present at concentrations of It tOO to Itt ,000 of that of the bulk earth. This is because the outstanding chemical characteristic of this group of elements is their siderophile nature; that is, their tendency to alloy with metallic iron. Because of this, once the earth became molten very early in its life history, these elements dissolved in the molten iron present at this stage and were removed from the outer accessible parts as this dense liquid sank to the centre of the earth to form the core. Although iron was the main instrument of concentration of the Group VIII metals, its much greater over-all abundance and its ability to combine with oxygen more easily than the others in the group means that significant amounts still remain in the oxidized portions of the earth.The fact that most of the Group VIII metals are available to use in workable concentrations at all is that they are 5 to 30 times more concentrated in the earth's mantle than the crust, as shown in line 4 of Table I. There has been a constant, if slow, interchange of matter between the mantle and the overlying crust throughout most of the earth's history and, under certain circumstances, this interchange has given rise to economic concentrations of metals."

Jan 1, 1979

By Hemant Agrawal, Arvind Kumar Mishra

Rock breakage using blasting is one of the important operations of the mining industry. The delay timing decides the initiation sequence of holes in the blasts and is a crucial factor to improve the overall blast performance. Blast-induced ground vibration is an undesired yet unavoidable outcome of blasting. Peak particle velocity (PPV) is commonly used to measure the magnitude of blast-induced ground vibration. Channelization and better utilization of explosive energy delay are provided between blast holes using initiating systems. The use of different initiation systems even on the same site results in a very significant difference in the values of PPV generated. Due to scattered delay timings of pyrotechnic detonators, the scaled distance predictor equations obtained become unreliable. The error/scatter in delay timing leads to overlapping of holes and hence increases in maximum charge per delay. In this paper, an analytical approach has been discussed to measure the overlapping of holes during blasting with initiation systems having inherent cap scatter. The analytical approach will be calculating the probable overlapping of holes due to scatter in delay timing and will help blasting engineers to understand the variation in maximum charge per delay due to pyrotechnic based initiating systems. In this study, a total number of 102 blasts were conducted using different initiation systems at two different opencast coal mine and 221 corresponding blast vibrations events were recorded.

Nov 10, 2020

By Terry J. Close

Between 1986 and 1989, at the request of the U. S. Bureau of Land Management, personnel from the U. S. Bureau of Mines Western Field Operations Center studied the highly-mineralized, 25,335-acre, Crack Canyon Wilderness Study Area (UT-060-028A), to evaluate its identified mineral resources. The 16-mi-long, 2-mi to 4-mi-wide stud/ area is on the southeast side of the San Rafael Swell, about 40 mi southwest of Green River, Emery County, southeast-central Utah. The study area is underlain by Mesozoic sedimentary beds. Uranium, the principle mineral resource, occurs in two formations. The principle uranium deposits are in mudstone, sandstone, and conglomerate lenses in the 22-mi-long outcrop of the Triassic Chinle Formation which parallels and straddles the northwest boundary of the study area, Some small low-grade uranium occurrences and an extensive gypsum deposit are hosted by the Jurassic-age rocks that underlie the southeast part of the study area.

Jan 1, 1989

By T Ireland

The Project Hobson tunnel excavation was the first use in New Zealand of an earth pressure balance (EPB) tunnel boring machine (TBM). The tunnelling on the project was very successful and break-through was achieved three weeks ahead of program, demonstrating that tunnelling can be undertaken in Auckland with a high degree of cost certainty.Project Hobson involved the replacement of an existing 90 year old above ground sewer that crosses Hobson Bay in Auckland, New Zealand, and which had reached the end of its economic life, with a 3 km long, 3.7 m internal diameter segmentally lined bored tunnel. The NZD$ 118 M project has provided several environmental benefi ts to the Owner, Watercare Services Ltd and the local community:· provide capacity to meet projected growth in the region,· virtually eliminate wastewater overflows into Hobson Bay and the Waitemata Harbour, and· remove an obtrusive visual feature and open up the bay for recreational purposes.Auckland’s bedrock is a weak sandstone/siltstone (East Coast Bays Formation), subject to infilled paleovalleys. The geology in the region has been significantly influenced by volcanic activity; 49 volcanoes are present within 20 km of the city centre.The paper describes the design and construction challenges for the projects, including TBM performance, ‘sticky spoil’ management, and risks associated with basalt lava flows and two paleovalleys. The paper also highlights the reasons for the success of the project, including a rigorous approach to risk management during design, and effective planning during construction. Other useful data such as the effect on the watertable caused by closed face tunnelling, and ‘faceloss’ estimates derived from settlement arrays are included in the paper.Project Hobson also saw the successful implementation of a Geotechnical Baseline Report – one of the first uses of this type of document in Australasia.

Mar 8, 2011

By Z. Xu, Z. Li

Colloidal interactions play a critical role in mineral processing, including grinding, physical separation (particularly flotation), dewatering, and tailings management. Despite great energy input in comminution to liberate valuables from gangues, heterocoagulation between valuables and gangues would prevent the separation of valuables from gangues. On the other hand, selective coagulation/flocculation to increase the size of desired fine particles could enhance physical separation and dewatering, while dispersion is needed for fine grinding. To control the state of colloidal dispersions by creating favorable conditions, it is of paramount importance to study colloidal interactions in a relevant system and understand underlying mechanisms. This review summarizes recent advances in developing the-state-of-the-art techniques and novel methods of measuring colloidal forces, including atomic force microscope, surface force apparatus, zeta potential distribution measurement, quartz crystal microbalance with dissipation, and our recently developed integrated dynamic force apparatus. The basic principle of each technique was introduced first, followed by a summary of critical information derived for the relevant mineral processing systems. Finally, the pros and cons of each technique were discussed to emphasize the use of complementary techniques that assist in solving fundamental problems in mineral processing.

By Ezequiel Pomachagua Quijada

En el Perú, el cierre de yacimientos es una etapa nueva de la vida productiva minera, pues a partir del año 2005 la norma rige y se les otorga un plazo de un año para elaborar y lograr la aprobación del plan de cierre de todas las unidades mineras. Sin embargo, en el año 2008-2009 se iniciaron las actividades de rehabilitación en unidades mineras que no habían logrado su aprobación. En ese sentido, el presente artículo señala la experiencia sostenida por la empresa C.M Centauro como ejemplo de cierre progresivo en botaderos de desmonte. La restauración se inició con el botadero suroeste a través de tres etapas: cierre progresivo, cierre final y postcierre. Así también planificó el cierre de los componentes desde el diseño mediante actividades como la estabilidad física, remoción, perfilado y conformación de banquetas, estabillidad química, extendido de caliza, batido de caliza, compactado de sustrato estabilidad hidrológica, biológica y revegetación.

Aug 1, 2015

By P. N. Calder, D. B. Apel, S. D. Butt

Mine-wide (MW) microseismic systems use widely spaced transducers to determine the source location and parameters of stronger microseismic events, while high frequency (HF) systems use fewer transducers to monitor local areas for the weaker events that can precede stronger events. Previous monitoring at the Creighton Mine indicated that an HF transducer located 120 m away from an active stope recorded two types of activity in response to production blasting: the first occurring at the same time as the production blasts and associated with the passage of the direct seismic waves from the blast through the local area, and the second occurring several hours later and associated with the arrival of a slower moving stress change through the rock mass (which was identified by the mine’s MW system). Interpretations of locally increased stress levels, based on analysis of the recorded HF events, correlated with the nearby occurrence of two strong seismic events. These results were applied to a similar monitoring trail at the Kidd Creek Mine where the transient stress changes induced by several development blasts were monitored. It was observed that increases in HF activity corresponded with the occurrence of MW events near the transducer location, and that fewer HF events were recorded the longer this occurred after the blast. Local geological features appeared to influence the number and occurrence of both HF and MW events.

Jan 1, 2000

By Gregory Beckstrom

"During a year of challenges in the mining industry, two groups collaborated Aug. 17- 20 for a joint conference on industrial minerals of the Upper Midwest. Hosted in Minneapolis, MN, the 4th Annual SME Twin Cities technical conference and the 51st Annual Forum on the Geology of Industrial Minerals (FGIM) drew attendees from throughout the United States and Canada.Highlights of the event included a one-day field trip on Aug. 17 to a crushed stone and gravel mining and processing operations near the Twin Cities, followed by a visit to a historic mine tunnel within the St. Peter sandstone formation. The latter was used as a speakeasy during America’s prohibition era. A two-day field trip on Aug. 19-20 made stops in central and northeastern Minnesota at a granite quarry and processing plant, a peat harvesting and packaging plant, an iron mine and taconite processing plant, and a silica sand storage and loading operation. In a nod to one of Minnesota’s celebrated luminaries, the group also stopped in Hibbing to visit the boyhood home of Robert Allen Zimmerman, better known to the rest of the world as Bob Dylan.A full-day technical program featuring talks on environmental impacts of silica sand mining, regulatory updates, mine land reclamation and methods for identifying construction material failures (alkali-silica reaction) was bookended by the two field trips.According to Minnesota state geologist Harvey Thorleifson, the keynote speaker of the technical program, “This joint SME and Forum on the Geology of Industrial Minerals conference is a reflection of the important role of the mining industry in society, of the important role that partnerships play, and of the prominence of industrial minerals on the Twin Cities region and iron ore on a national scale.” He added, “While this is a tough year for the mining industry in the region, we are confident in the strength of the profession and the industry in the medium term, as we anticipate a superb SME national conference in Minneapolis in 2018.”"

Jan 1, 2015

By Congcong Chen, Bo Ma

When assessing the safety of a tailings dam, the constant weight method (CWM) is one of the most commonly used methods. However, when the evaluation indicator value suggests serious defects, the evaluation value is often inconsistent with the actual situation. To address this issue, the variable weight method (VWM) is introduced to assess the safety of the tailings dam. Initially, a three-layer indicator system for dam failure safety assessment is built, and individual indicator values are divided into four grades. Then, an appropriate state variable weight function is constructed and relevant parameters are determined. Finally, a case study is illustrated to verify the effectiveness of the model. The assessment results of the VWM more closely represent the actual situation than that of the CWM, which is more helpful for decision makers and technicians to take scientific and reasonable precautionary measures, thereby improving the safety management of the tailings pond.

Oct 8, 2022

By T. F. Anstett

The Bureau of Mines evaluated the potential availability of chrysotile, amosite, and crocidolite asbestos from 42 properties in market economy countries. This resulted in the development of tonnage-cost relationships indicating the quantity of grades 3 through 7 asbestos at various average total costs of production at 0% and 15% rates of return on invested capital. The availability of grades 2 and 8 was also evaluated, but since each is produced at only one property, no analytical results were given. Total demonstrated recoverable chrysotile fiber potentially available of grades 3 through 7 from the 42 properties evaluated follow: 1.59 million t, 21.00 million t, 16.74 million t, 15.54 million t, and 19.27 million t, respectively. The total amount of crocidolite is 1.69 million t. Owing to the good potential for discovery and development of new deposits, long- term availability of fiber of all three types is not in jeopardy. However, many of the crocidolite properties evaluated in the northern Cape crocidolite field of South Africa have relatively small demonstrated resources, and new deposits will have to be exploited by the late 1990's to sustain projected levels of production.

Jan 1, 1985

By E. Kumar, L. A. Kumar

"A methodology is proposed to develop an optimization model to understand the impact of transporting minerals, from mines to the final destination, on air quality. Recently, there has been increasing concern about the combined effects of multiple activities over many years, and the regional environmental changes brought about by a single project. Environmental issues in the iron ore industry have highlighted the need to broaden the cumulative impact assessment. In this study, we simulated the optimal routes and quantity of materials needed to meet the destination plant demand based upon environment constraints (level of air pollution), as well as the cost of transportation and availability of materials. Multiple scenarios were developed to analyse the effects of changes in routes, alternative transport system (or multi-modal split), traffic congestion, and the cumulative impacts on air quality. The air quality impact zones of the study area were demarcated using a GIS technique. The expected outcome of the study is the selection of a suitable transport system for a particular site with the least impact on air quality, including the transportation route, relative to the minimum cost of transportation of the minerals from the mines to their final destination. The proposed methodology is evaluated with a case study. IntroductionIn India, the process of environmental impact assessment (EIA) has been focused primarily on the local impacts of projects, without considering regional environmental effects. Environmental clearances for proposed projects are based on reports of local impacts. However, any developmental project poses a potential risk to the environment as a whole, and not just in the immediate vicinity of the project. Recently, there has been increased concern about the combined effects of multiple activities over many years—the regional environmental changes due to development of a single project (Dutta, Mahatha, and De, 2004). Environmental issues throughout the country, particularly in the iron ore industry, have emphasized the need to broaden the analysis to include the combined impacts, or those forecast for a proposed region, on an existing environment. The most significant adverse environmental consequences of iron ore transportation are the deterioration of biodiversity and air quality (Kumar and Ajay, 2015)."

Jan 1, 2017