Search Documents

By A. W. Deurbrouck

Five preparation plants employing concentrating tables for washing 3/8- inch to 0 raw coal were tested. Two of the plants were washing Pittsburgh-bed coal, two were washing Pocahontas-bed coal, and one was washing Elkhorn-bed coal. Samples of the feed to and products from the tables were collected over the normal operating shift. These samples were analyzed, and complete performance criteria were determined. The results of this study show that the concentrating table is an effective fine-coal cleaner even when operating at 40 percent over the recommended 10 tons per hour feed rate. Recovery efficiencies for the 3/8-inch to 200- mesh size fraction ranged from 97.3 to 99.3 percent; maximum yield errors and ash errors were 2.4 and 1.0 percent, respectively; probable errors ranged from 0.074 to 0.115 specific gravity units and error areas from 52 to 73 square centimeters. The amount of minus 200-mesh material in the water used for feed water and dressing water to the table had no significant effect on the sharpness of the separation achieved but did have an effect on the ash content of the clean- coal product. In the one plant studied, the substitution of fresh water for plant circulating water reduced the ash content of the clean coal by about 6 percentage points.

Jan 1, 1963

By T. M. Garland

A nomographical approach is proposed as a fast, easy-to-use, and reason- ably accurate method for estimating expected discounted cash flow (DCF) rate of return and payout time for onshore development drilling and oil production. All costs pertaining to drilling, completing, and equipping development wells, annual expenses of operation, maintenance, and taxes incurred in producing properties, and crude oil prices were considered in developing the nomographs. This report briefly outlines the origin, derivation, and use of the nomographs.

Jan 1, 1973

By Ademar Lopes, Victor Silva, Heitor Silva, Gustavo Usero, Roberto Rolo, Lucas Pereira, Gabriel Moreira, João Lague, Arthur Endlein, Matheus Feitosa

Grade control models are supposed to provide a higher resolution than long-term or interim models. However, available grids from diamond or reverse circulation drilling do not provide that required resolution. In this study, a geostatistical workflow is proposed to integrate available grade data from production blastholes with its operational parameters taken when drilling downhole. The step of geological logging can be replaced by machine learning models for classifying blastholes into lithologies and hardness classes. Next, indicator and ordinary kriging use the classified blastholes and previous data for estimating the model domains and the grades within each one. The workflow is applied in a world class iron ore mine in Brazil.

Jun 25, 2023

By C. L. Severy

The Reeder No. 1 well was drilled by the Bureau of Mines in cooperation with the Geological Survey as agents for the Defense Plant Corporation. The well is south of Crescent Junction near Thompson, Grand County, Utah. It was started May 5, 1942, and completed August 3, 1942, for the purpose of con-firming the presence of magnesium salts in a deeply buried bed. Drilling was done under contract by the Mack Drilling Co. This report contains an outline of the physical features of the well, a brief history of drilling, and a description of the deposits and occurrences of oil and gas encountered in the drill hole. The work performed by the Bureau of Mines is described in considerable detail, with particular emphasis on drilling procedure and sampling. The report is concluded with a brief description of core-sample preparation for analyses. Appendix A comprises a log of the drill hole, and appendix B is a tabulation of analyses of cores.

Jan 1, 1949

Seam gases are the most important atmos- phere contaminants in Australian collieries, their importance increasing with depth; C02 as well as CH4 may be important in intruded envir- onments. The generally high rank of the coal, with low moisture content, makes for abnormal dust production. The other contaminants are introduced and subject to better control, in- cluding products of spontaneous combustion. Due to market situations the generally lower rank and higher sulphur coals more prone to self heating are mined less. Future mining at greater depths should see greater problems with atmosphere contaminants.

Jan 1, 1983

By H. C. George

CAREFUL- sampling and good judgment as to probable recoveries are important factors in estimates of ore reserves, based on prospecting drilling results, but other factors are equally as important and may be more misleading and perhaps disastrous if not properly interpreted. Some of these are: 1. The case where no, ore is shown in the "sludgings," when, as a matter of fact, the drill has passed through a thick sheet of ore which has been broken up and washed away into open crevices. In numerous cases, later mining operations have shown that this has happened. This condition may be discovered by shooting the drill .hole at the point where the open crevices occur, but shooting should not be done until after the drill hole is completed, because the resulting shattered formation may salt the drill hole at lower levels. 2. The case where rich cuttings are shown for a thickness of 20 or 30 ft., when ore was encountered in only the first sludging. Owing to soft or loose formation, the ore from the first sludging has salted the lower sludgings. The presence of large pieces of ore and a similar ratio between zinc and iron assays in the lower sludgings frequently indicate this condition. In the lower sludgings, the presence of oxidized ore in unaltered limestone sometimes shows this condition. 3. The case where the drill hole shows a considerable thickness of ore; but owing to the presence of a vertical sheet of ore, perhaps not more than 1 in. thick, at the place where the drill hole is located, the good assays resulting might be misleading. If this condition is suspected, the drilling of several more holes within a distance of 10 or 15, ft. will usually show it.

Jan 1, 1921

By T. F. Witherbee

It is proposed to give, first, a description of the works; second, a report of the first six months of the present blast; and third, such improvements as have been suggested by the practical working. The site selected for this furnace was, at the time of commencing work, October, 1872, entirely covered by the navigable waters of Lake Champlain. A coffer-dam was first built of cribs of round timber filled with stone, forming three sides, while the shore answered for the fourth. Considerable excavating was done with a steam-dredge, a hole being left for it to pass out. The opening was then built up, and the cribbing banked up with blue clay from the bottom of the lake, to render it water-tight and the dam pumped out; the remainder of the excavating being done by hand. All of the foundations, with the exception of the elevator-tower, and fifteen feet of the east side of hot blast, rest on the Potsdam sandstone, which forms the shore line, dipping into the lake at an angle of fifteen degrees. Owing to jogs in the formation, a much greater depth was found necessary than was at first anticipated, the foundation under the stack

By T. F. Witherbee

IT is proposed to give, first, a description of the works ; second, a report of the first six months of the present blast; and third, such improvements as have been suggested by the practical working. The site selected for this furnace was, at the time of commencing work, October, 1872, entirely covered by the navigable waters of Lake Champlain. A coffer-dam was first built of cribs of round timber filled with stone, forming three sides, while the shore answered for the fourth. Considerable excavating was done with a steam-dredge, a hole being left for it to pass out. The opening was then built up, and the cribbing banked up with blue clay from the bottom of the lake, to render it water-tight and the dam pumped out; the remainder of the excavating being done by hand. All of the foundations, with the exception of the elevator-tower, and fifteen feet of the east side of hot blast, rest on the Potsdam sandstone, which forms the shore line, dipping into the lake at an angle of fifteen degrees. Owing to jogs in the formation, a much greater depth was found necessary than was at first anticipated, the foundation under the stack

Jan 1, 1876

By L. S. Rivett, U. M. Oko

The Strathcona mine, with a large new underground operation and concentrator, was recently brought into\ production by Falconbridge Nickel Mines Ltd. The tailings disposal and water utilization problems at Strathcona are described in this paper, with sections devoted to the Moose Lake watershed system, tailing impounds, the construction of dams and the operation of the Moose Lake neutralization plant for the elimination of acidity, including the equipment used.

Jan 1, 1971

By J-P Franzidis

A study was undertaken to determine the effect of five industrial frothers on the relationship between entrainment recovery and water recovery. The experiments were conducted using a Batequip rectangular 60 liter steel cell which was run in parallel with the first cell in a copper/silver prefloat rougher circuit. The concentration of the frothers ranged from 2.5 g/ton to 8.4 g/ton. The experiments were repeated at three different froth depths. A power function was found to fit this relationship with no discontinuity in the relationship caused by the changes in frother type and concentration and froth depth.

Jan 1, 2000

By Stephen E. Stewart

This document presents the explosion-proof enclosures used severity of certification tests solutions to linear transient thermal and stress analyses of in underground mines. The results were used to assess the for enclosure windows relative to possible loads occurring in the actual mine environment. Cast iron electric light enclosures with polycarbonate and glass windows were analyzed under steady state thermal conditions (light burning) and for thermal shocks corresponding to an internal explosion (ignition of volatile mine gas) or external quenching (mine water spray system). Thermal shocks to the enclosure, caused by ignited gases or water spray, were applied via a series of load steps in the transient analysis. The temperature dependence of material I properties and of the film heat transfer coefficients were included in the model. The work demonstrates that thermally induced stresses are strongly influenced by the way the window is mounted in the enclosure. It also shows that the MSHA Thermal Shock Test, if performed on an unsupported lens (or window), produces lower stresses than the lens (or window) may experience in the mine environment.

Jan 1, 1984

By Christopher Haycocks

Because of growing pressure from government and consumers to produce more coal, the mining industry must improve existing techniques and devise more efficient mining methods. Mining of the thicker, shallower and geologically superior coal seams in the western United States is being subjected to increasing pressure from environmentalists; and so in order to meet the demand, the coal industry is exhausting the more accessible surface seams and beginning to mine seam of over 1,000 feet in depth and less than. 30 inches in thickness. The longwall mining system is the natural choice for extracting deep and thin coal seams, as it operates almost independently of the overburden rock stress. Due to the added fact that longwall mining is an inherently more productive method than room and pillar mining, many coal producers are looking to it as a means of increasing productivity without a corresponding cost increase. The consistent rise in application of longwall mining in the United States in the last decade illustrates the excellent potential of this technique for the future. American mining conditions are geologically different from those in Europe where longwall mining has been highly developed and extremely successful. Although numerous successes have been recorded in the U.S. with this mining system, a substantial number of failures have also occurred. These failures are due primarily to roof control problems usually over the face, in the tail entry, or both. Another problem area for American operators contemplating the use of this method has been correct selection of equipment, which should be custom fitted to local mining conditions for optimum productivity. It is essential that correct estimates for chock resistances, support densities, supported and unsupported roof spans, as well as rates of advance and length of working faces be provided to optimize mining conditions. Unless extensive pilot projects are planned engineers must choose their equipment correctly at the outset. A typical investment in longwall equipment will amount to several millions of dollars.

Jan 1, 1979

By Luis Alberto Medina

La característica principal de la composición de un cuerpo mineralizado es la heterogeneidad, dado que sus elementos no son iguales. En ese sentido, la prueba de heterogeneidad en el mineral de Cerro Verde, es una guía para la geología, mina, metalurgia y laboratorio químico, que busca optimizar los protocolos de muestreo y minimizar errores en las muestras tales como: Error Fundamental; Error de Segregación, generado por una muestra o submuestra cuando es cuarteada; Error de Extracción, generado por una muestra pequeña o insignificante colectada o tomada, y Error de Preparación, producido por la pérdida excesiva de finos. De acuerdo al estudio, el presente trabajo señala que la heterogeneidad de cobre total, cobre soluble en ácido y cobre soluble en cianuro, desarrollada para el mineral de Cerro Verde, es baja, lo que permite un manejo operacional sencillo para el muestreo con protocolos más simples, mientras que el parámetro más heterogéneo es el cobre soluble en cianuro y el protocolo podría ser afectado en el error fundamental.

Sep 13, 2001

By R. P. D. Graham

It is almost exactly two hundred years since the foundations of the mining and metallurgical industries in Canada were laid. There '."'as nothing spectacular about this early start. It had to do with the most basic phases of these industries-the mining of coal and iron ore, and the manufacture of cast and wrought iron. At several points along the coast of Cape Breton island, coal seams may be seen outcropping quite conspicuously, and it is probable that they had been observed, and possibly worked in a small way, in very early times. However that may be, these coal seams have the distinction of being the first in North America of which there is any printed record, reference to them appearing in a volume by Nicolas Denys which was published in Paris in 1672. Regular coal mining in the district did not commence until about fifty years later, however. The metallurgists started their operations along the north shore of the St. Lawrence river. Here, at many points between Montreal and Quebec, are to be found deposits of bog iron ore, and in 1 730 a furnace for smelting such ore was established on the St. Maurice river. The St. Maurice forges continued in operation until 1880, and throughout that long period they were famed for the fine quality of castings produced, and also for a-superior wrought iron.

Jan 1, 1924

By J. L. Hoover

The goal of the drill bit consumption study was to develop an equation(s) based on various components that affect bit drill wear and use the equation(s) to estimate the consumption of bits during production drilling. Drill bit data from various geographic locations were compiled and used to develop linear regression equations using the Microsoft Excel Software. Multiple drill bit consumption equations were developed and statistical analysis was used to verify the accuracy of those equations. The equations will allow mining companies to more accurately forecast drill bit consumption when evaluating new mine properties. This capability becomes increasingly beneficial to forecasting as the cost of consumables increases.

Jan 1, 2012

The New Zealand Minerals Industry is small but growing. Over the next 10 years it will be facing stiff international competition for skills to support this growth, particularly from Australia who are forecasting that a further 70 000 people will be employed by 2015.   The value of commodities mined and quarried in NZ continues to increase; and the value of coal, metals and industrial minerals production reached $1.505 billion in 2006, an increase of 15 per cent on 2005. Production increases will continue à. Latest Crown Minerals statistics show that national prospecting and exploration expenditure rose to $29.9 million in the year ended March 31 2006 û an increase of 46 per cent from the $20.4 million spent in the March 2005 year. The equivalent 2001 year expenditure was only $2.48 million.   The industry already experiences difficulty in recruiting the people it needs with ongoing demand for skilled underground miners, trades people, and mining professionals. This discussion paper will outline the national context with regard to labour, skills and training. It will suggest options and provide an opportunity for conference participants to discuss the way forward.

Jan 1, 2007

By Morris P. H

A trial embankment was constructed using coarse coal mine reject on a deposit of crusted coal mine tailings at New Hope Colliery, located in the Bundamba District of the West Moreton Coalfields in South East Queensland, Australia. The purpose of the trial embankment was to assess the load carrying capacity and settlement behaviour of the crusted tailings, including an assessment of strength gain in the tailings under the influence of the fill. Prior to construction of the trial embankment, a site investigation of the tailings deposit was carried out. This comprised vane shear strength testing, together with disturbed sampling and undisturbed block sampling for the purposes of laboratory testing. Following the site investigation, settlement plates and standpipes were installed at various depths and locations within the tailings in the vicinity of the proposed embankment. The instrumentation enabled the magnitudes and distributions of settlement and pore pressure within the tailings to be determined during and following construction of the embankment. The embankment was constructed using coarse reject in three equal lifts to a height of 3.0 m. The tailings sustained a maximum settlement under the weight of the fill of 290 mm, representing about 4.2 ii of the average initial thickness of the tailings and a loss of embankment height of about 9.7 %. By the end of the monitoring period the strength of the softer tailings underlying therust had roughly doubled under the influence of tha cmbarikment

Jan 1, 1990

By R. S. Douglas

Introduction The operations of The Granby Consolidated Mining, Smelting and Power Company, L1mited, have always been concerned with the mining of low-grade copper ores. In the fifty years of this Company's existence, nearly 60,000,000 tons of such material has been successfully mined and treated. During these years, many changes in mining practice took place. However, at Copper Mountain, due to the large tonnages of very low grade material, it was realized that something more than changing mining methods would have to take place if these low-grade orebodies were to be mined at a profit and the Company and. its employees enjoy many years of successful operation and employment. Production costs were mounting commensurately with rising taxes and the increasing cost of supplies, labour, freight, and smelting, while the value of the product on the market was not increasing in price to compensate for the higher costs of production. A survey of the mineable ore in 1944 indicated that, of the 12,000,000 tons in the reserves, only 3,500,000 tons was now profitable ore. This reduction in the commercial ore reserves was a serious matter, as it meant that the mine had only two years of life at the profitable shipp1ng rate of 4,800 tons per day. Further, the location in the mine of the orebodies making up the 3,500,000 tons was not suitable for such high production.

Jan 1, 1950

By Claudio Asioli

"The project’s goal was to construct the Al Ghazala Intercontinental, a multi-use development in the bay area of Tripoli overlooking the Mediterranean Sea. The site of the project is located approximately 500 ft (150 m) from the Mediterranean coast, near the Al Ghazala roundabout in the town center of Tripoli, Libya. The investor of the project was Magna Properties Group, Ltd. – Libya, the main contractor was Man Enterprise S.A.L., and the design and construction management was performed by Dar Al-Handasah Engineering. Trevi S.p.A. was contracted to perform the design and construction of the anchored diaphragm walls and dewatering systems for the excavation of a two-level basement car park, which extends across the full footprint of the site.The site was approximately 640 ft by 230 ft (195 m by 70 m) in plan and nearly flat. The groundwater level typically varies from about 11 ft to 23 ft (3.4 m to 7.0 m) above mean sea level. To construct the required raft foundation, it was necessary to excavate the area down to El. -15.7 ft to -26.3 ft (-4.8 m to -8.0 m), which resulted in an excavation depth ranging from about 27 ft to 39 ft (8.3 m to 12.0 m) below the existing ground surface.Subsurface ConditionsThe subsurface site investigation was performed in three phases by Al-Tamier Engineering Consulting Bureau. During Phase 1, a preliminary investigation was undertaken during the early stages of the project to obtain information about the general stratigraphy and groundwater level at the site. Phase 2 was performed to obtain subsurface information and design parameters, and Phase 3 was performed as a supplementary ground investigation to investigate unexpected ground conditions identified during Phase 2. In total, 14 boreholes were drilled to depths ranging from about 80 ft to 180 ft (24 to 55 m). The generalized subsurface profile is quite heterogeneous, and is predominantly composed of sand with silt and gravel that is underlain by limestone, calcarenite and claystone"

Jan 1, 2017

By Claudio Asioli

"The project’s goal was to construct the Al Ghazala Intercontinental, a multi-use development in the bay area of Tripoli overlooking the Mediterranean Sea. The site of the project is located approximately 500 ft (150 m) from the Mediterranean coast, near the Al Ghazala roundabout in the town center of Tripoli, Libya. The investor of the project was Magna Properties Group, Ltd. – Libya, the main contractor was Man Enterprise S.A.L., and the design and construction management was performed by Dar Al-Handasah Engineering. Trevi S.p.A. was contracted to perform the design and construction of the anchored diaphragm walls and dewatering systems for the excavation of a two-level basement car park, which extends across the full footprint of the site.The site was approximately 640 ft by 230 ft (195 m by 70 m) in plan and nearly flat. The groundwater level typically varies from about 11 ft to 23 ft (3.4 m to 7.0 m) above mean sea level. To construct the required raft foundation, it was necessary to excavate the area down to El. -15.7 ft to -26.3 ft (-4.8 m to -8.0 m), which resulted in an excavation depth ranging from about 27 ft to 39 ft (8.3 m to 12.0 m) below the existing ground surface. Subsurface ConditionsThe subsurface site investigation was performed in three phases by Al-Tamier Engineering Consulting Bureau. During Phase 1, a preliminary investigation was undertaken during the early stages of the project to obtain information about the general stratigraphy and groundwater level at the site. Phase 2 was performed to obtain subsurface information and design parameters, and Phase 3 was performed as a supplementary ground investigation to investigate unexpected ground conditions identified during Phase 2. In total, 14 boreholes were drilled to depths ranging from about 80 ft to 180 ft (24 to 55 m). The generalized subsurface profile is quite heterogeneous, and is predominantly composed of sand with silt and gravel that is underlain by limestone, calcarenite and claystone."

Jan 1, 2017